Upload
others
View
8
Download
0
Embed Size (px)
Citation preview
EM00136061 rev. 2.1
EN
DE
ES
FR
IT
PT
TK
TEKNAEVO TPG
INSTRUCTIONS MANUAL
HANDBUCH
MANUAL DE INSTALACION
MANUEL D’INSTALLATION
MANUALE D’INSTALLAZIONE
MANUAL DE INSTALAÇÃO
KULLANIM KLAVUZU
EM00136061 rev. 2.1 1
Control panel – TEKNA TPG
Access to the programming menu
When pressed during the pump operation phase, it cyclically displays the programmed values on the
display; When pressed at the same time or keys, it increases or decreases a valuedependent on the selected operating mode. During programming it carries out an “enter” function,meaning that it confirms entry to the various menu levels and modifications within the same.
Starts and stops the pump. In the event of a level alarm (alarm function only), flow alarm and activememory alarm, it deactivates the signal on the display.
Used to “exit” the various menu levels. Before definitively exiting the programming phase, you will beasked if you wish to save any changes
Used to run upwards through the menu or increase the numerical values to be changed. Can be usedto start dosage in Batch mode
Used to run downwards through the menu, or decrease the numerical values to be changed.
Flashing green LED during dosage
Red LED that lights up in various alarm situations
Electrical connections
1
2Alarm relay
3 Pole +
4 Pole -
4-20 mA input signalInput Impedante: 200ohm
5
6
-Remote control input (start-stop)-Pause signal input
7
8
-Frequency signal input (water-meter pulse-sender)-Trigger signal input
9
10Flow sensor input
B Input level control
B
EM00136061 rev. 2.1 2
Programmiermenü Tekna TPG
You can access the programming menu by pressing the key for over three seconds. The keys can
be used to run through the menu items, with the key being used to access changes.The pump is programmed in constant mode in the factory. The pump automatically returns to the operating modeafter 1 minute of no activity. Any data entered in these circumstances will not be saved.
The key can be used to exit the various programming levels. Upon exiting programming, the display willshow:
Exit ExitDon’t Save
Save to confirm the selection
+-
+-Pump FuntionsConfiguration
+-Pump Functions
Pump Functions
Paragrafo 1
Paragraph 10
Paragraph 11
Paragraph 12
Paragrafo 13Paragraph 14
Paragraph 15
Paragraph 16
Paragraph 9
Paragraph 2
Paragraph 3
Paragraph 4
Paragraph 5
Paragraph 6
Paragraph 7
Paragraph 8
Pump Functions
Pump Functions
Pump Functions
Pump Functions
Pump Functions
Pump Functions
PROG
MainMenu
SettingMenu
FunctionsMenu
Paragraph 17PausN.Open
EM00136061 rev. 2.1 3
Setting the LanguageProgramming Operation
-
-
-
- -
Pump Functions
Max flow rate
Alarm Relay
Language
P100%
N.Open
English
PROG
+-
Makes it possible to select the language. The pump is set inEnglish in the factory.
Changes can be made by pressing the key, then
using the keys to set the new value. Press toconfirm and return to the main menu
Paragraph 1 – Manual DosageProgramming Operation
+-
Pump FuntionsConfiguration
Pump Functions
PROG
The pump operates in constant mode. The flow can only be manually
regulated by pressing the keys at the same time to increase
the flow, or the keys to decrease it.
Display during Operation Display during Setting (MODE key)
MAN FFFLev Stop P100%
Operating mode
Man = Manual
Alarms and statuses
Lev = Level alarm
Flw = Flow alarms
FLOW sensorstatus
Pump status
Empty = pump in start
Stop = pump stationary
Paus = pump in pause
Current dosage speed(depends on selected unit of
measurement)
Percentage, Frequency,l/h, Gph, ml/m MAN
P100%
Operating mode
Man (during manual modification of theflow it displays the correspondingfrequency value)
Current dosage value
Modify the maximum flow by pressing the+ or – keys at the same time
Paragraph 2 - Dosage Proportional to Signal 0/4-20Programming Operation
+-
-
-
+-
+-
Pump FuntionsConfiguration
Pump Functions0/4 - 20 mA
0/4 - 20 mA
0/4 - 20 mA
Low 4.0mA
High 20.0mA
PROG
The pump proportionally doses at a signal of (0)4-20 mA. On the basis ofthe factory settings, the pump interrupts dosage at 4mA and doses at the
maximum set frequency when it receives 20 mA. These two values can bemodified during programming. The maximum frequency can be modified
during operation, by pressing the keys at the same time to
increase the flow, or the keys to decrease it.
EM00136061 rev. 2.1 4
Display during Operation Display during Setting (MODE key)
mA FFF 4-20Lev Stop P100%
Operating mode
mA
Alarms and statuses
Lev = Level alarm
Flw = Flow alarm
FLOW sensorstatus
Programmed value Programmed interval value
(default: 4-20)
Pump status Empty = pump in start
Stop = pump stationary
Paus = pump in pause
Current dosage value(depends on the selected unit
of measurement)
Percentage, Frequency,l/h, Gph, ml/m
Low 00.0 mA P100%
Operating mode Displays the Low and High
value in sequence
Input mAvalue
Current dosage value Makes it possible to modify the
maximum dosage value by pressingthe + or – buttons at the same time
Paragraph 3 - Dosage Proportional to Signal 20-4/0 mAProgramming Operation
+-
-
-
+-
+-
Pump FuntionsConfiguration
Pump Functions20-4/0 mA
Low 20.0mA
High 4.0mA
PROG
20-4/0 mA
20-4/0 mA
The pump proportionally doses at a signal of 20-4(0) mA. On the basis ofthe factory settings, the pump interrupts dosage at 20mA and doses at themaximum set frequency when it receives 4 mA. These two values can bemodified during programming. The maximum frequency can be modified
during operation, by pressing the keys at the same time to
increase the flow, or the keys to decrease it.
Display during Operation Display during Setting (MODE key)
mA FFF 20-4Lev Stop P100%
Operating mode
mA
Alarms and statuses
Lev = Level alarm
Flw = Flow alarm
FLOW sensorstatus
Programmed value Programmed interval value
(default: 20-4)
Pump status Empty = pump in start
Stop = pump stationary
Paus = pump in pause
Current dosage value(depends on the selected unit
of measurement)
Percentage, Frequency,l/h, Gph, ml/m
High 00.0 mA P100%
Operating mode Displays the Low and High
value in sequence
Input mAvalue
Current dosage value Makes it possible to modify the
maximum dosage value by pressingthe + or – buttons at the same time
Paragraph 4 – Proportional to External Impulses (multiplication)Programming Operation
+-
-
-
-
+-
+-
+-
Pump FuntionsConfiguration
Pump FunctionsMultiply (1:n)
n 4
Timeout 0s
Memory Off
PROG
Multiply (1:n)
Multiply (1:n)
Multiply (1:n)
The pump doses in proportion to an external signal (i.e.: impulse launchcounter). With every signal received, the pump makes the programmed“n” number of strikes. The pump automatically sets the dosage frequency,adapting it to the time that passes between two successive signals. It ispossible to set the time (timeout) in seconds, beyond which the pumpresets the interval count in order to avoid dosages over excessively longtimes. The pump has a memory function, which signals the reception of asignal during dosage. If set to Off, it merely sends a signal, if set to On itsends a signal and memorises the impulses, then executes them when ithas finished receiving signals.
The value of “n” can be modified during operation, by pressing the
keys at the same time to increase the flow, or the keys todecrease it.
EM00136061 rev. 2.1 5
Display during Operation Display during Setting (MODE key)
1:n FFF MMM 1Lev Stop 0
Operating mode 1:n = impulse
multiplication
Alarms and statuses Lev = Level alarm Flw = Flow alarm Mem = Memory alarm
FLOWsensorstatus Programmed
value of n
Pump status Empty = pump in start Stop = pump stationary Paus = pump in pause
Current dosage value Displays stroke
countdown
Memoryfunction
status
Timeout n0s 1
Displays programmedtimeout
Current dosage value
Displays the value of n. Thiscan be modified by pressingthe + or – keys at the sametime
Paragraph 5 – Proportional to External Impulses (division)Programming Operation
+-
-+-
Pump FuntionsConfiguration
Pump FunctionsDivide (n:1)
n 4
PROG
Divide (n:1)
The pump doses in proportion to an external signal (i.e.: impulse launchcounter). At every “n” signals, the pump makes a strike. You can set thevalue of “n” during programming. By programming the value of “n” you setthe maximum dosage %. This value can be modified during operation, by
pressing the keys at the same time to increase the flow, or the
keys to decrease it.
Display during Operation Display during Setting (MODE key)
N:1 FFF 4Lev Stop P100%
Operating mode 1:n = impulse
multiplication
Alarms and statuses Lev = Level alarm Flw = Flow alarm
FLOWsensorstatus
Programmedvalue of n
Pump status Empty = pump in start Stop = pump stationary Paus = pump in pause
Current dosage value Maximum dosage
percentage
n:1 66 P100%
Operating mode
Programmed value
Value of n
Current dosage value
The dosage % can be modifiedby pressing the + or – keys atthe same time
Effectivevalue of “n”
Paragraph 6 – Proportional to External Impulses (batch dosage)Programming Operation
+-
-
-
-
+-
+-
+-
Pump FuntionsConfiguration
Pump FunctionsBatch mode (1:c)
Q.ty 10.0ml
Time 10s
Memory Off
PROG
Batch mode (1:c)
Batch mode (1:c)
Batch mode (1:c)
The pump doses in proportion to an external signal (i.e.: impulselaunch counter). In this case, it is possible to set the quantity to bedosed in ml and the time within which to complete dosage.
Dosage can be started manually by pressing the key, or by
using a remote control. The key interrupts dosage, which can
be reset by pressing the key, or started again by pressing the
key again.The quantity to be dosed can be modified during operation, by
pressing the keys at the same time to increase the flow,
or the keys to decrease i.
EM00136061 rev. 2.1 6
Display during Operation Display during Setting (MODE key)
Batch FFF MMM 7.0mlLev Stop 0
Operating mode
Batch
Alarms and statuses Lev = Level alarm
Flw = Flow alarm
Mem = Memory alarm
FLOWsensorstatus Programmed value
Quantity in ml
Pump status Empty = pump in start
Stop = pump stationary
Paus = pump in pause
Current dosage value
Gradually displaysthe dosed quantity
Memoryfunction
status
Q.ty 7.0ml7.0ml
Operating mode Displays in sequence: quantity to
be dosed, dosage time and pumpfrequency
Dosage value
The quantity can be modified by pressing the+ or – keys at the same time
Paragraph 7 – Proportional to External Impulses (ppm dosage)Programming Operation
+-
-
-
-
+-
+-+-
+-
+-
+-
Pump FuntionsConfiguration
Pump Functionsppm Mode
ppm 50
Pulse/l 4 Pulse/L 4
L/pulse 4
Conc(%) 100
Memory Off
PROG
ppm Mode
ppm Mode
ppm Mode ppm Mode
ppm Mode
ppm Mode
-
The pump doses in proportion to an external signal (i.e.:impulse launch counter), automatically calculating therelationship between incoming signals and pump strokes onthe basis of the programmed ppm value.The data to be entered is the ppm value, the impulse/litreratio (or litre/impulse) of the counter and the concentration ofthe product to be dosed.The dosage frequency can be modified during operation, by
pressing the keys at the same time to increase
the flow, or the keys to decrease it.
Display during Operation Display during Setting (MODE key)
Ppm FFF MMM 10Lev Stop F300s/m
Operating mode ppm
Alarms and statuses Lev = Level alarm
Flw = Flow alarm
Mem = Memory alarm
FLOWsensorstatus Programmed ppm
value
Pump status
Empty = pump in start
Stop = pump stationary
Paus = pump in pause
Current dosage value
Frequency
Memoryfunction
status
cc/stroke 1.00.23 F300s/m
Operating mode
Displays in sequence: cc/stroke,impulses/minute on the counter and %concentration of the chemical product
Dosage value
Programmedppm value
The dosage frequency value can bemodified by pressing the + or – keysat the same time.
EM00136061 rev. 2.1 7
Paragraph 8 – Timed Dosage (Frequency signal input “TRIGGER” activated)Programming Operation
+-
-
-
-
+-
+-
+-
Time
Quantity 100ml
Delay 0.01.50
interv. 0.01.50
PROG
Time
Time g.hh.mm
Time g.hh.mm
Configuration
Pump functions
Configuration
Pump functions
-
-
Trigger Mode
Pause Input Mode
-Trigger Mode
-Trigger Mode
Trigger Mode
N. Open N. Open
N. Closed
Disable
Trigger Mode
After receipt of the TRIGGER signal set, the pump doses a quantitythat can be programmed in ml. It is possible to set a delay time beforethe dosing (Delay) and the interval between subsequent dosings(Interv.) as illustrated in the diagram:
By setting for example an Interval. time = 0, a system is obtained inwhich the programmed quantity is dosed after each TRIGGER signal(with any delay that has been set):
It is possible to start the dosing by pressing the + key, which, inpractice, simulates the Trigger signal.The Trigger signal can be set to N. Open (it is activated when theinput passes from the open to the closed mode) or to N. Closed (it isactivated when the input passes from the closed to the open mode).The Trigger signal is locked during dosing (its receipt is neither storednor managed).The Pause (Remote input) input cannot be programmed and itsactivation stops the dosing, while its further deactivation makes thesystem wait again for the Trigger signal for a new dosing.
The dosage frequency can be modified while the pump is operating,
by pressing the keys at the same time to increase the
frequency, or the keys to decrease it.
Display during Operation Display during Setting (MODE key)
Timer FFF 7,0 mlStop P 0%
Operating mode
Timer
Alarms and statuses Liv = level alarm
Flow = flow alarm or….Release wait
FLOWsensor status Programmed value
Quantity in ml
Pump status Dry = pump starting up Stop = pump stop
Restart = pump restart
Value of the dosing inprogress
Percentage ofstrokes/minmax
Q.tà 20,0ml20,0ml P 100%
Operating mode The following are shown in sequence:
quantity to dose, delay in d.hh.mm.and interval in d.hh.mm
Dosing value
Programmedquantity in ml
Value of the dosing percentage,which can be modified bypressing the + or – keys
Delay Interv.
QuantityTrigger
Delay
Trigger
Ritardo
Release
EM00136061 rev. 2.1 8
Paragraph 8 – Timed Dosage (Frequency signal input “TRIGGER” not activated)Programming Operation
+-
-
-
-
+-
+-
+-
Tempo
Quantity 100ml
Delay 0.01.50
Interval 0.01.50
PROG
Time
Time g.hh.mm
Time g.hh.mm
Configuration
Pum functions
Configuration
Pum functions
-
-
Trigger Mode
Pause Input Mode
Disable
Restart Timer
+-
-Pause Input ModeRestart Timer
-Pause Input ModeFreeze Time
Pause Input ModePause Dosing
The pump doses a programmed quantity in ml. It is possible to set apump delay time (Delay) when the pump is started and an intervalbetween two successive dosings (Interval), as illustrated in thediagram:
The Delay and Interval times are in dd.hh.mm (days, hours,minutes)
The Pause input can be programmed in three different modes:1. FreezeTime: when the pause is activated, the system cuts
out the current time count and restarts it when the pause isdeactivated.
2. Pause Dosing: with the pause activated, the systemcontinues to count time the and stops the dosing.
3. Restart Timer: when the pause is activated, the systemstops the dosing and when the pause is deactivated thecount starts again from the beginning.
The dosage frequency can be modified while the pump is operating,
by pressing the keys at the same time to increase the
frequency, or the keys to decrease it.
Display during Operation Display at start-up (MODE key)
Timer FFF 7.0 mlLiv Stop P 0%
Operating mode
Timer
Alarms and Levelstatuses = level alarm
Flow= flow alarm
FLOWsensorstatus
Programmed value Quantity in ml
Pump status Dry = pump starting up Stop = pump stopping Restart = pump restarting
Value of dosing inprogress: Percentage of
strokes/min max
Q.tà 20,0ml20,0ml P 100%
Operating mode The following are shown in sequence:
quantity to dose, delay in d.hh.mm.and interval in d.hh.mm
Dosing value
Programmedquantity in ml
Value of the dosing percentage,which can be modified bypressing the + or – keys
Paragraph 9 – Setting the Maximum FlowProgramming Operation
-
--
Pump Functions
Max flow rate Max flow rate
Max flow rate
P100% P100%
F320s/m
PROG
-+-
+-
This makes it possible to set the maximum flow offered bythe pump, and the programmed mode (% or frequency) isused as the standard unit of measurement when displaying
the flow. Changes can be made by pressing the key,
then using the keys to set the new value. Press
to confirm and return to the main menu
Paragraph 10 – Setting the Alarm Relay
Delay Interv.
Quantity
EM00136061 rev. 2.1 9
Programming Operation
-
-
- -
Pump Functions
Max flow rate
Alarm Relay
P100%
N.Open
PROG
+-
In the absence of an alarm situation, it can be set as open(default) or closed.
Changes can be made by pressing the key, then using
the keys to set the new value. Press toconfirm and return to the main menu
Paragraph 11 – Flow CalibrationProgramming Operation
-
-
-
Pump Calibration
Pump Calibration
Automatic Cal.
Automatic Cal.
Automatic Cal.
Pump Calibration
0,23 cc/stroke
cc/stroke 0,23
Start 100 strok.
Strokes 100
ml 20
Manual
PROG
+-
+-
Pump Calibration
Automatic
-
The memorized cc value per strike appears in the mainmenu. It can be calibrated in two different ways:MANUAL – manually enter the cc value per strike using the
keys and confirm by pressing the keyAUTOMATIC – the pump makes 100 strikes, which are
started by pressing the key. At the end of this process,
enter the quantity sucked up by the pump using the
keys and confirm by pressing the key.The entered figure will be used in flow calculations.
Paragraph 12 - StatisticsProgramming Operation
The main menu displays the pump operation times. By
pressing the key you can access other statistics:- Strokes = number of strokes made by the pump- Q.ty (L) = quantity dosed by the pump in litres; this figure iscalculated on the basis of the memorised cc/stroke value- Power = number of pump starts
- Reset = use the to reset the counters (YES) or
otherwise (NO), then confirm by pressing the key.
Pressing the key will take you back to the main menu.
EM00136061 rev. 2.1 10
Paragraph 13 – PasswordProgramming Operation
-
-
-
Password
Password
****
0000
PROG
+ -
By entering the password, you can enter the programmingmenu and see all the set values. The password will berequested whenever you seek to modify them.The flashing line indicates the number than can be modified.
Use the key to select the number (from 1 to 9), and the
key to select the number to be modified. Confirm by
pressing the key. By setting “0000” (default), thepassword is eliminated.
Paragraph 14 – Flow AlarmProgramming Operation
-
-Alarms
Alarms
Alarm Flow
Alarm Flow
Alarm Flow - On
Flow Off
Flow Off
Off
On
Signals 6
PROG
+
+
-
--
-
ESC
-
This makes it possible to activate (deactivate) the flowsensor.
When activated (On), press the key to access therequest for the number of signals that the pump waits forbefore an alarm is triggered. The number flashes when you
press the key, and you can then use the keys
to set the value. Confirm by pressing the key. Press
to return to the main menu
Paragraph 15 – Level AlarmProgramming Operation
-
-Alarm Level
Alarm Flow
Alarms
Level Stop
Alarms
Level Alarm
Stop
Alarm
PROG
-
-
ESC-
This makes it possible to set the pump when the levelsensor alarm is activated. In other words you can decidewhether to stop dosage (Stop) or simply activate the alarmsignal without stopping dosage.
Changes can be made by pressing the key, then using
the keys to set the alarm type. Confirm by pressing
the key. Press to return to the main menu
Paragraph 16 – Flow Display UnitProgramming Operation
This makes it possible to set the dosage unit ofmeasurement on the display.
Changes can be made by pressing the key, then using
the keys to set the unit of measurement, choosingbetween L/h (liters/hour), Gph (Gallons/hour), ml/m(milliliters/minute) or standard (% or frequency, depending
on settings). Press to confirm and return to the mainmenu
EM00136061 rev. 2.1 11
Paragraph 17 - Setting the PauseProgramming Operation
- -PausN.Open
PROG
+-
Configuration
+
The pump can be paused by remote input.The factory setting is Normally Open.
Changes can be made by pressing the key, then
using the keys to set the new value ( N. OPEN orN. CLOSED).
Press to confirm and return to the main menu.
Display contrast adjustment.
For adjusting the display contrast keep the key pressed and within 5 seconds press the keys or toincrease or decrease the contrast.
AlarmsDisplay Cause Interruption
Fixed alarm LEDFlashing word “Lev”I.e. Man
Lev P100%
End of level alarm, withoutinterrupting pump operation
Restore the liquid level.
Fixed alarm LEDFlashing words “Lev” and “stop”I.e. Man
Lev Stop P100%
End of level alarm, with interruptionto pump operation
Restore the liquid level.
Flashing word “Mem”I.e. 1:n 6
Mem
The pump receives one or morepulses during dosage with memoryfunction on Off
Press the key
Flashing word “Mem”I.e. 1:n M 6
Mem
The pump receives one or morepulses during dosage with memoryfunction on On
When the pump finishes receivingexternal impulses, it returns thememorized strokes
Fixed alarm LEDFlashing word “Flw”I.e. Man F
Flw P100%
Active flow alarm. The pump hasnot received the programmednumber of signals from the flowsensor.
Press the key
I.e. Parameter ErrorPROG to default
Internal CPU communication error.
Press the key to restore thedefault parameters.
EM00136061 rev. 2.1 1
Steuertafel – TEKNA TPG
Zugriff auf das Programmiermenü
Während des Pumpenbetriebs: Durch Drücken werden die programmierten Werte zyklisch auf dem
Display angezeigt; bei gleichzeitigem Drücken der Tasten wird ein Wert, je nachausgewähltem Betriebsmodus, erhöht bzw. verringert. Während der Programmierung übernimmtdiese Taste die Funktion “Enter”, d.h. dass der Zugriff auf die verschiedenen Menüstufen und die dortvorgenommenen Veränderungen bestätigt werden.
Startet und stoppt die Pumpe. Wenn ein Füllstandsalarm (nur Alarmfunktion), ein Durchflussalarmund ein Memoryalarm aktiv ist, deaktiviert diese Taste die Anzeige auf dem Display.
Zum “Verlassen” der verschiedenen Menüstufen. Vor dem endgültigen Verlassen der Programmierung,öffnet sich ein Speicherungsdialog für Veränderungen.
Blättert nach oben im Menü, oder erhöht die numerischen Werte, die verändert werden sollen. ImBatch-Modus kann diese Taste die Dosierung starten.
Blättert nach unten im Menü, oder verringert die numerischen Werte, die verändert werden sollen.
Grüne Led, die während dem Dosiervorgang blinkt.
Rote Led, die sich bei den verschiedenen Alarmsituationen einschaltet.
Anschlusse Elektrik
1
2
Relaisausgang (Alarm)Wahlweise Öffner (NC)oder Schliesser (NO)
3 Pole +
4 Pole -
4-20 mA Eingangs-SignalEingang Widerstand:200 ohm
5
6
-Eingang Fernbedienung(Start-Stop)-Eingang Pause-signal
7
8
-Impuls –Eingang (Impuls – Wasserzähler)-Eingang externes Trigger-signal
9
10
Eingang Fluss - Sensor
B Eingang Füllstandkontrolle
B
EM00136061 rev. 2.1 2
Programmiermenü Tekna TPG
Durch über drei Sekunden langes Drücken der Taste erhalten Sie Zugriff auf die Programmierung. Über die
Tasten können Sie die Menüpunkte durchblättern. Über die Taste erhalten Sie Zugriff auf dieVeränderungen.Werkseitig ist die Pumpe auf den Konstant-Modus programmiert. Die Pumpe kehrt nach 1 Minute Inaktivitätautomatisch zum Betriebs-Modus zurück. In diesem Fall werden etwaig eingegebene Daten nicht gespeichert.
Über die Taste verlassen Sie die Programmierstufen. Bei Verlassen der Programmierung wird auf demDisplay folgendes angezeigt:
Exit Exit
No Save
SaveZur Bestätigung der
Auswahl
+-
+-Pump FuntionsConfiguration
+-Pump Functions
Pump Functions
Absatz 1
Absatz 10
Absatz 11
Absatz 12
Absatz 13Absatz 14
Absatz 15
Absatz 16
Absatz 9
Absatz 2
Absatz 3
Absatz 4
Absatz 5
Absatz 6
Absatz 7
Absatz 8
Pump Functions
Pump Functions
Pump Functions
Pump Functions
Pump Functions
Pump Functions
PROG
Hauptmenü
MenüEinstellungen
MenüFunktionen
Absatz 17PausN.Offen
EM00136061 rev. 2.1 3
SprachauswahlProgrammierung Funktionsweise
-
-
-
- -
P100%
PROG
+-
Konfiguration
KonfigurationPump Funktion
Max Durchfluss
Al. Relais
N.Offen
SpracheDeutsch
Ermöglicht die Sprachauswahl. Werkseitig ist die SpracheEnglisch eingestellt.
Durch Drücken von erhalten Sie Zugriff auf die
Veränderung. Stellen Sie dann über die Tasten
den Wert ein. Über bestätigen Sie und werden zumHauptmenü zurückgeleitet.
Absatz 1 – Manuelle DosierungProgrammierung Funktionsweise
+-
PROG
Konfiguration
KonfigurationPump Funktion
Pump Funktion
Die Pumpe arbeitet im Konstant-Modus. Die Förderleistung wird manuell
geregelt. Durch gleichzeitiges Drücken der Tasten wird die
Förderleistung erhöht bzw. über die Tasten verringert.
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
MAN FFFLev Stop P100%
Betriebs-Modus Man = Manuell
Alarme und Zustände Liv = Füllstandsalarm Fls = Durchflussalarm
Zustand desDurchflusssensors
Zustand der Pumpe Leer = Pumpenstart Stop = Pumpe steht Pause = Pumpe in Pause
Wert der laufenden Dosierung(hängt von der ausgewählten
Messeinheit ab) %, Frequenz, l/h, Gph,
ml/m F320s/mP100%
Betriebs-Modus Man (während der manuellen Veränderung
der Förderleistung wird der der Frequenzentsprechende Wert angezeigt)
Wert der laufenden Dosierung Verändert die maximale Förderleistung
durch gleichzeitiges Drücken der Tasten +und -
Absatz 2 – Proportionale Dosierung 0/4-20 mAProgrammierung Funktionsweise
+-
-
-
+-
+-
0/4 - 20 mA
0/4 - 20 mA
0/4 - 20 mA
PROG
Konfiguration
KonfigurationPump Funktion
Pump Funktion
Niedrig 4.0mA
Hoch 20.0mA
Die Pumpe dosiert proportional zu einem Signal zwischen (0)4 und 20mA. Werkseitig ist die Pumpe so eingestellt, dass sie die Dosierung bei 4mA unterbricht und mit der eingestellten Höchstfrequenz dosiert, wenn sie20 mA empfängt. Während der Programmierung können diese beidenWerte verändert werden. Die Höchstfrequenz kann während des Betriebs
verändert werden. Durch gleichzeitiges Drücken der Tasten
wird die Förderleistung erhöht bzw. über die Tasten verringert.
EM00136061 rev. 2.1 4
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
mA FFF 4-20Lev Stop P100%
Betriebs-Modus mA
Alarme und Zustände Lev = Füllstandsalarm Flw = Durchflussalarm
Zustand desDurchflusssensors
Programmierter Wert Wert des programmierten
Intervalls (Default: 4-20)
Zustand der Pumpe Leer = Pumpenstart Stop = Pumpe steht Pause = Pumpe in
Pause
Wert der laufendenDosierung
(hängt von der ausgewähltenMesseinheit an)
%, Frequenz, l/h, Gph,ml/m
Niedrig 00.0 mA P100%
Betriebs-Modus Zeigt der Reihe nach die
Werte Low und High an
EingehendermA-Wert
Wert der laufenden Dosierung Ermöglicht die Veränderung des
maximalen Werts der Dosierung durchgleichzeitiges Drücken der Tasten + und -
Absatz 3 – Proportionale Dosierung 20-4/0 mAProgrammierung Funktionsweise
+-
-
-
+-
+-
20-4/0 mA
PROG
20-4/0 mA
20-4/0 mA
Konfiguration
KonfigurationPump Funktion
Pump Funktion
Niedrig 20.0mA
Hoch 4.0mA
Die Pumpe dosiert proportional zu einem Signal zwischen 20 und 4(0)mA. Werkseitig ist die Pumpe so eingestellt, dass sie die Dosierung bei 20mA unterbricht und mit der eingestellten Höchstfrequenz dosiert, wenn sie4 mA empfängt. Während der Programmierung können diese beidenWerte verändert werden. Die Höchstfrequenz kann während des Betriebs
verändert werden. Durch gleichzeitiges Drücken der Tasten
wird die Förderleistung erhöht bzw. über die Tasten verringert.
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
mA FFF 20-4Lev Stop P100%
Betriebs-Modus mA
Alarme und Zustände
Liv = Füllstandsalarm Fls = Durchflussalarm
Zustand desDurchflusssensors
Programmierter Wert Wert des programmierten
Intervalls (Default: 20-4)
Zustand der Pumpe Leer = Pumpenstart
Stop = Pumpe steht
Pause = Pumpe in Pause
Wert der laufendenDosierung
(hängt von der ausgewähltenMesseinheit ab)
%, Frequenz, l/h, Gph,ml/m
Hoch 00.0 mA P100%
Betriebs-Modus Zeigt der Reihe nach die
Werte Low und High an
EingehendermA-Wert
Wert der laufenden Dosierung Ermöglicht die Veränderung des
maximalen Werts der Dosierung durchgleichzeitiges Drücken der Tasten + und -
Absatz 4 – Proportionale Dosierung mit externen Impulsen (Multiplikation)Programmierung Funktionsweise
+-
-
-
-
+-
+-
+-
n 4
PROG
Konfiguration
KonfigurationPump Funktion
Pump FunktionMultipl (1:n)
Multipl (1:n)
Multipl (1:n)Zeitabschalt 0s
Multipl (1:n)Speicher off
Die Pumpe dosiert proportional zu einem externen Signal (z.B.:Wasseruhr mit Impulsgeber). Bei jedem empfangenen Signal führt diePumpe die programmierten “n“ Hübe aus. Die Pumpe stellt automatischdie Dosierfrequenz ein und passt diese an den Zeitraum an, der zwischenzwei aufeinander folgenden Signalen liegt. Es ist möglich, diesenZeitraum (Timeout), über den hinaus die Pumpe die Zeitzählung wiedervon Null beginnt, in Sekunden zu programmieren, um zu langeDosierungen zu vermeiden. Die Pumpe verfügt über eine Memory-Funktion, die den Empfang eines Signals während der Dosierungsignalisiert. Wenn sie auf OFF gestellt ist, beschränkt sie sich darauf, zusignalisieren. Wenn sie auf ON gestellt ist, signalisiert und speichert siedie Impulse und führt diese aus, wenn sie keine Signale mehr empfängt.Der Wert “n“ kann während des Betriebs verändert werden. Durch
gleichzeitiges Drücken der Tasten wird die Förderleistung
erhöht bzw. über die Tasten verringert.
EM00136061 rev. 2.1 5
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
1:n FFF MMM 1Lev Stop 0
Betriebs-Modus 1:n =
Impulsmultiplikation
Alarme und Zustände Liv = Füllstandsalarm Fls = Durchflussalarm Mem = Memory-Alarm
Zustand desDurchfluss-
sensors Programmiertern-Wert
Zustand der Pumpe Leer = Pumpenstart Stop = Pumpe steht Pause = Pumpe in Pause
Wert der laufendenDosierung
ZeigtRückwärtszählungder Hübe an
Zustand derMemory-Funktion
Zeitabschalt n0s 1
Zeigt den programmiertenTimeout an
Wert der laufenden Dosierung
Zeigt den n-Wert an, derdurch gleichzeitiges Drückender Tasten + und – verändertwerden kann
Absatz 5 – Proportionale Dosierung mit externen Impulsen (Division)Programmierung Funktionsweise
+-
-+-n 4
PROG
Konfiguration
KonfigurationPump Funktion
Pump FunktionDivid (n:1)
Divid (n:1)
Die Pumpe dosiert proportional zu einem externen Signal (z.B.:Wasseruhr mit Impulsgeber). Alle “n“ empfangenen Signale führt diePumpe einen Hub aus. Geben Sie während der Programmierung denWert “n“ ein. Durch Programmieren des Werts “n“ wird der maximaleprozentuale Anteil (%) der Dosierung eingestellt. Dieser Wert kannwährend des Betriebs verändert werden. Durch gleichzeitiges Drücken
der Tasten wird er erhöht bzw. über die Tastenverringert.
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
N:1 FFF 4Lev Stop P100%
Betriebs-Modus 1:n =
Impulsmultiplikation
Alarme und Zustände Liv = Füllstandsalarm Fls = Durchflussalarm
Zustand desDurchfluss-
sensorsProgrammierter
n-Wert
Zustand der Pumpe Leer = Pumpenstart Stop = Pumpe steht Pause = Pumpe in Pause
Wert der laufendenDosierung
% maximaleDosierung
n:1 66 P100%
Betriebs-Modus
Programmierter Wert n-Wert
Wert der laufenden Dosierung Prozentuale Veränderung (%)
der Dosierung durchgleichzeitiges Drücken derTasten + und -
Tatsächlicher“n”-Wert
Absatz 6 – Proportionale Dosierung mit externen Impulsen (Batch-Dosierung)Programmierung Funktionsweise
+-
-
-
-
+-
+-
+-
Batch mode (1:c)
PROG
Batch mode (1:c)
Batch mode (1:c)
Batch mode (1:c)
Konfiguration
KonfigurationPump Funktion
Pump Funktion
Menge 10.0ml
Zeit 10s
Speicher off
Die Pumpe dosiert proportional zu einem externen Signal (z.B.:Wasseruhr mit Impulsgeber). In diesem Fall kann die Menge, diedosiert werden soll, in ml und die Zeit, in der die Dosierungdurchgeführt werden soll, programmiert werden.
Die Dosierung kann durch Drücken der Taste oder über eine
Fernsteuerung manuell gestartet werden. Die Taste unterbricht
die Dosierung. Diese kann daraufhin durch Drücken der Taste
auf Null gestellt oder durch erneutes Drücken von wiedergestartet werden.Die Dosiermenge kann während des Betriebs verändert werden.
Durch gleichzeitiges Drücken der Tasten wird die
Förderleistung erhöht bzw. über die Tasten verringert.
EM00136061 rev. 2.1 6
Anzeige während des Betriebs Anzeige während der Einstellung (Taste MODE)
Batch FFF MMM 7.0mlLev Stop 0
Betriebs-Modus Batch
Alarme und Zustände Liv = Füllstandsalarm Fls = Durchflussalarm Mem = Memory-Alarm
Zustand desDurchfluss-
sensors ProgrammierterWert
Menge in ml
Zustand der Pumpe Leer = Pumpenstart Stop = Pumpe steht Pause = Pumpe in Pause
Wert der laufendenDosierung Zeigt schrittweise
die dosierte Mengean
Zustand derMemory-Funktion
Q.ty 7.0ml7.0ml
Betriebs-Modus Zeigt der Reihe nach an:
Dosiermenge, Dosierzeit undPumpenfrequenz
Wert der Dosierung Veränderung der Menge durch
gleichzeitiges Drücken der Tasten +und -
Absatz 7 – Proportionale Dosierung mit externen Impulsen (PPM-Dosierung)Programmierung Funktionsweise
+-
-
-
-
+-
+-+-
+-
+-
+-
ppm Mode
ppm 50
Pulse/l 4 Pulse/L 4
L/pulse 4
PROG
-
Konfiguration
KonfigurationPump Funktion
Pump Funktion
PPM Modus
PPM Modus PPM Modus
PPM Modus
PPM Modus
PPM Modus
Konz.(%) 100
Speicher off
Die Pumpe dosiert proportional zu einem externen Signal(z.B.: Wasseruhr mit Impulsgeber), wobei automatisch dasVerhältnis zwischen den Eingangssignalen und denPumpenhüben entsprechend des programmierten ppm-Wertsberechnet wird.Die einzugebenden Daten sind der ppm-Wert, das VerhältnisImpulse/Liter (bzw. Liter/Impulse) der Wasseruhr und dieKonzentration des Produkts, das dosiert werden soll.Während des Betriebs kann die Dosierfrequenz verändert
werden. Durch gleichzeitiges Drücken der Tasten
wird sie erhöht bzw. über die Tasten verringert.
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
Ppm FFF MMM 10Lev Stop F300s/m
Betriebs-Modus ppm
Alarme und Zustände Liv = Füllstandsalarm Fls = Durchflussalarm Mem = Memory-Alarm
Zustand desDurchfluss-
sensors Programmierterppm-Wert
Zustand der Pumpe Leer = Pumpenstart Stop = Pumpe steht Pause = Pumpe in Pause
Wert der laufendenDosierung
Frequenz
Zustand derMemory-Funktion
cc/stroke 1.00.23 F300s/m
Betriebs-Modus Zeigt der Reihe nach an:
Hubvolumen, Impulse/Minute derUhr und Konzentration in % deschemischen Produkts
Wert der Dosierung Programmierter
ppm-Wert
Wert der Dosierfrequenzkann durch gleichzeitigesDrücken der Tasten + und– verändert werden
EM00136061 rev. 2.1 7
Absatz 8 – Getaktete Dosierung (Eingang Frequenzsignal “TRIGGER” aktiviert)Programmazione Funzionamento
+-
-
-
-
+-
+-
+-
Zeit
Menge 100ml
Verzog. 0.01.50
Interval 0.01.50
PROG
Zeit
Zeit g.hh.mm
Zeit g.hh.mm
Konfiguration
Pumpen funktionenKonfiguration
Pumpen funkionen
-
-
Trigger Modus
Pause Eingabem.
-Trigger Modus
-Trigger Modus
Trigger Modus
N. Offen N. Offen
N. Geschlossen
gesperrt
Trigger Modus
Nach Empfang des eingestellten TRIGGER-Signals dosiert die Pumpeeine in ml programmierbare Menge. Es kann eine Verzögerungszeitvor der Dosierung (Verzögerung) und der Zeitabstand zwischenaufeinander folgenden Dosierungen (Pause) eingestellt werden, wieim Schema gezeigt:
Wird zum Beispiel eine Zeit Pause = 0 eingegeben, erhält man einSystem, bei dem die programmierte Menge nach jedem TRIGGER -Signal dosiert wird (mit der etwaig eingestellten Verzögerung):
Es ist auch möglich, die Dosierung durch Drücken der Taste + zustarten, die praktisch das Trigger-Signal nachahmt.Das Trigger-Signal kann auf N.Offen eingestellt werden (es aktiviertsich, wenn der Eingang von der Betriebsart geöffnet zur Betriebsartgeschlossen übergeht), oder auf N. Geschlossen (es aktiviert sich,wenn der Eingang von der Betriebsart geschlossen zur Betriebsartgeöffnet übergeht).Das Trigger-Signal ist während der Dosierung blockiert (seinEmpfang wird weder gespeichert, noch verwaltet).Der Eingang Pause (Eingang Fernbedienung) kann nichtprogrammiert werden und seine Aktivierung blockiert die Dosierung,während die nachfolgende Deaktivierung das System wieder in denZustand Warten auf das Trigger-Signal für eine neue Dosierungversetzt.
Während des Pumpenbetriebs kann die Dosierfrequenz verändert
werden, indem gleichzeitig die Tasten gedrückt werden,
um die Frequenz zu erhöhen bzw. die Tasten , um sie zuverringern.
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
Timer FFF 7,0 mlStop P 0%
Betriebsart
Timer
Alarme und Zustände Füllst. = Füllstandsalarm Durchfluss =
Durchflussalarm oderWartezeit Abgabe
StatusDurchflusssensor
ProgrammierterWert
Menge in ml
Pumpenstatus Leer = Pumpe gestartet Stop = Pumpe gestoppt Reinitialisierung =
Pumpe wird neugestartet
Wert der laufendenDosierung
ProzentualerAnteil derHübe/min.max.
Menge 20,0 ml20,0 ml P 100
Betriebsart Es werden der Reihenfolge nach
angezeigt: Zu dosierende Menge,Verzögerung in T/S/M und Pause inT/S/M
Wert der Dosierung Programmierte
Menge in ml
Wert des prozentualen Anteils derDosierung, durch Drücken derTasten + oder - veränderbar
Verzögerung Interv.
MengeTrigger
Verzögerung
Trigger
Verzögerung
Trigger
EM00136061 rev. 2.1 8
Absatz 8 – Getaktete Dosierung (Eingang Frequenzsignal “TRIGGER” nicht aktiviert)Programmazione Funzionamento
+-
-
-
-
+-
+-
+-
Zeit
Menge 100ml
Verzog. 0.01.50
Interval 0.01.50
PROG
Zeit
Zeit g.hh.mm
Zeit g.hh.mm
Konfiguration
Pumpen funktionenKonfiguration
Pumpen funktionen
-
-
Trigger Modus
Pause Eingabem.
gesperrt
Time neu start.
+-
-Pause Eingabem.Time neu start.
-Pause Eingabem.Block Zeit
Pause Eingabem.Dosierpause
Die Pumpe dosiert eine in ml programmierbare Menge. Es kann eineStartverzögerung der Pumpe (Verzögerung) und der Zeitabstandzwischen zwei aufeinander folgenden Dosierungen (Pause)eingestellt werden, wie im Schema gezeigt:
Die Verzögerungs- und Pausenzeiten sind in T/S/M (Tage,Stunden, Minuten) angegeben.
Der Pausen-Eingang kann auf drei unterschiedliche Artenprogrammiert werden:
1. Blocki Zeit: Bei aktivierter Pause blockiert das System dieZählung der aktuellen Zeit und nimmt sie wieder auf, wenndie Pause deaktiviert wird.
2. Dosierpause: Bei aktivierter Pause zählt das System dieZeit weiter und blockiert die Dosierung.
3. Time neu start.: Bei aktivierter Pause blockiert das Systemdie Dosierung und startet die Zählung neu, wenn die Pausedeaktiviert wird.
Während des Pumpenbetriebs kann die Dosierfrequenz verändert
werden, indem gleichzeitig die Tasten gedrückt werden,
um die Frequenz zu erhöhen bzw. die Tasten , um sie zuverringern.
Anzeige während des BetriebsAnzeige während der Einstellung (Taste
MODE)
Timer FFF 7,0 mlFüllst. Stop P 0%
Betriebsart
Timer
Alarme und ZuständeFüllst. = Füllstandsalarm
Durchfluss =Durchflussalarm
StatusDurchflusssensor
Programmierter Wert Menge in ml
Pumpenstatus Leer = Pumpe gestartet Stop = Pumpe gestoppt Reinitialisierung = Pumpe
wird neugestartet
Wert der laufendenDosierung Prozentualer
Anteil derHübe/min. max.
Menge 20,0ml20,0ml P 100%
Betriebsart Es werden der Reihenfolge
nach angezeigt: Zudosierende Menge,Verzögerung in T/S/M undPause in T/S/M
Wert der Dosierung Programmierte
Menge in ml
Wert des prozentualen Anteils derDosierung, durch Drücken derTasten + oder - veränderbar
Absatz 9 – Einstellung der maximalen FörderleistungProgrammierung Funktionsweise
-
--
Pump Functions
Max flow rate Max flow rate
Max flow rate
P100% P100%
F320s/m
PROG
-+-
+-
Ermöglicht die Einstellung der maximalen Förderleistung,die die Pumpe erreichen kann, und der programmierteBetriebs-Modus (% oder Frequenz) wird zur Anzeige derFörderleistung in der Standardmesseinheit. Durch
Drücken von erhalten Sie Zugriff auf die
Veränderung. Stellen Sie dann über die Tasten
den Wert ein. Über bestätigen Sie und werden zumHauptmenü zurückgeleitet.
Verzögerung Interv.
Menge
EM00136061 rev. 2.1 9
Absatz 10 – Einstellung AlarmrelaisProgrammierung Funktionsweise
-
-
- -
Pump Functions
Max flow rate
Alarm Relay
P100%
N.Open
PROG
+-
Wenn keine Alarmsituation vorliegt, kann es auf geöffnet(werkseitige Einstellung) oder geschlossen gestellt werden.
Durch Drücken von erhalten Sie Zugriff auf die
Veränderung. Stellen Sie dann über die Tasten
den Wert ein. Über bestätigen Sie und werden zumHauptmenü zurückgeleitet.
Absatz 11 – Kalibrierung der FörderleistungProgrammierung Funktionsweise
-
-
-
Strokes 100
ml 20
PROG
+-
+-
-
Konfiguration
0,23 ml/HubPumpe Kalibr
Pumpe KalibrMl/Hub 0,23Manuell
Pumpe Kalibr
Pumpe KalibrAutomatik
Automatik KalStart 100 Hube
Automatik Kal
Automatik Kal
Im Hauptmenü erscheint das gespeicherte Hubvolumen. Eskann auf zwei Arten kalibriert werden:
MANUELL – Geben Sie über die Tasten manuell
das Hubvolumen ein und bestätigen Sie überAUTOMATISCH – Die Pumpe führt 100 Hübe aus, die über
die Taste gestartet und über bestätigt werden. Wenndiese Hübe ausgeführt worden sind, geben Sie über die
Tasten die von der Pumpe angesaugte Menge ein
und bestätigen Sie über .Der eingegebene Wert wird bei der Berechnung derFörderleistungen verwendet.
Absatz 12 – StatistikenProgrammierung Funktionsweise
-
-
-
-
-
-
NO
PROG
+-ESC
Konfiguration
StatistikStunden 10
StatistikHuebe 1000
StatistikMenge(L) 100
StatistikNetzstrom 10
StatistikRucksetzen
Stat. Rucksetzen
StatistikStunden 10
Im Hauptmenü werden die Betriebsstunden der Pumpe
angezeigt. Durch Drücken der Taste erhalten SieZugriff auf die anderen Statistiken:- Strokes = Anzahl der von der Pumpe ausgeführten Hübe- Q.ty(L) = in Litern ausgedrückte von der Pumpe dosierteMenge; dieser Wert wird entsprechend des gespeichertenHubvolumens berechnet.- Power = Anzahl der Pumpenstarts
- Reset = über die Tasten können Sie wählen, obSie die Uhr auf Null stellen möchten (YES) oder nicht (NO),
über bestätigen Sie.
Durch Drücken von gelangen Sie zum Hauptmenüzurück.
EM00136061 rev. 2.1 10
Absatz 13 – PasswortProgrammierung Funktionsweise
-
-
-
****
0000
PROG
+ -
Konfiguration
Passwort
Passwort
Durch Eingabe des Passworts erhalten Sie Zugriff auf dieProgrammierung und können sich alle eingegebenen Werteansehen. Jedes Mal wenn Sie versuchen, diese Werte zuverändern, erscheint ein eigener Passwortdialog.Die blinkende Linie zeigt die veränderbare Nummer an.
Wählen Sie über die Taste die Nummer aus (zwischen
1 und 9), wählen Sie über die Taste die Nummer aus,die verändert werden soll, und bestätigen Sie anschließend
über . Durch Eingabe von “0000” (werkseitigeEinstellung) wird die Passwortabfrage übersprungen.
Absatz 14 – DurchflussalarmProgrammierung Funktionsweise
-
-Off
On
PROG
+
+
-
--
-
ESC
-
Konfiguration
Alarme Alarm FlussFluss off
Alarm Fluss
Alarm Fluss-onSignale 6
AlarmeFluss off
Ermöglicht die Aktivierung (Deaktivierung) desDurchflusssensors.Wenn er einmal aktiviert ist (ON), erhalten Sie durch
Drücken der Taste Zugriff auf den Abfragedialog, wieviele Signale die Pumpe abwartet, bevor Sie einen Alarm
auslöst. Durch Drücken von beginnt die Nummer zu
blinken. Stellen Sie dann über die Tasten den
Wert ein. Über bestätigen Sie. Durch Drücken von
werden Sie zum Hauptmenü zurückgeleitet.
Absatz 15 – FüllstandsalarmProgrammierung Funktionsweise
-
-Stop
PROG
-
-
ESC-
Konfiguration
AlarmeFuellstand stop
Alarm Fuellstand
Alarm FlussAlarme
AlarmeFuellstand alarme
Ermöglicht die Einstellung des Zeitpunkts, an dem derFüllstandsalarm aktiviert wird, also auch ob die Dosierungblockiert (Stop), oder einfach nur das Alarmsignal aktiviertwerden soll, ohne dabei die Dosierung zu blockieren.
Durch Drücken von erhalten Sie Zugriff auf die
Veränderung. Stellen Sie dann über die Tasten
die Alarmart ein. Über bestätigen Sie. Durch Drücken
von werden Sie zum Hauptmenü zurückgeleitet.
Absatz 16 – Anzeigeeinheit der FörderleistungProgrammierung Funktionsweise
-
-UnitStandard Standard
EM00136061 rev. 2.1 11
Absatz 16 - Einstellung PauseProgrammierung Funktionsweise
- -PausN.Offen
PROG
+-
Konfiguration
+
Steuereingang: Pumpe Stop / Start.Werkseinstellung: Bei Schließerkontakt (elektrisch leitendeVerbindung zwischen beiden Anschlussklemmen)Pumpenstop.
Durch Drücken von erhalten Sie Zugriff auf dieVeränderung.
Stellen Sie dann über die Tasten den Wert ein (N.OFFEN oder N. GESCHLOSSEN).
Über bestätigen Sie und werden zum Hauptmenüzurückgeleitet.
Absatz 17 - Einstellung PauseProgrammierung Funktionsweise
- -PausN.Offen
PROG
+-
Konfiguration
+
Steuereingang: Pumpe Stop / Start.Werkseinstellung: Bei Schließerkontakt (elektrisch leitendeVerbindung zwischen beiden Anschlussklemmen)Pumpenstop.
Durch Drücken von erhalten Sie Zugriff auf dieVeränderung.
Stellen Sie dann über die Tasten den Wert ein (N.OFFEN oder N. GESCHLOSSEN).
Über bestätigen Sie und werden zum Hauptmenüzurückgeleitet.
Display - Einstellung Kontrast
Für die Einstellung des Display-Kontrasts wird die Taste festgedrückt und innerhalb von 5 Sekunden mit den
Tasten oder der gewünschte Kontrast festgelegt
AlarmeAnzeige Ursache Unterbrechung
Alarm-Led leuchtet kontinuierlichDer Schriftzug Lev blinktBsp.: Man
Lev P100%
Alarm Füllstand nicht ausreichend,ohne Unterbrechung desPumpenbetriebs
Flüssigkeit nachfüllen
Alarm-Led leuchtet kontinuierlichDer Schriftzug Lev und Stop blinktBsp.: Man
Lev Stop P100%
Alarm Füllstand nicht ausreichend,mit Unterbrechung desPumpenbetriebs
Flüssigkeit nachfüllen
Der Schriftzug Mem blinktBsp.: 1:n 6
Mem
Die Pumpe empfängt einen odermehrere Impulse während derDosierung mit Memory-Funktion inOff-Stellung
Die Taste drücken
Der Schriftzug Mem blinktBsp.: 1:n M 6
Mem
Die Pumpe empfängt einen odermehrere Impulse während derDosierung mit Memory-Funktion inOn-Stellung
Wenn die Pumpe keine externenImpulse mehr empfängt, führt siedie gespeicherten Hübe aus
Alarm-Led leuchtet kontinuierlichDer Schriftzug Flw blinktBsp.: Man F
Flw P100%
Durchflussalarm aktiv, die Pumpehat nicht die programmiertenSignale vom Durchflusssensorempfangen.
Die Taste drücken
Bsp.: Parameter ErrorPROG to default
Interner Kommunikationsfehler derCPU. Die Taste drücken, um auf
die Default-Parameterrückzustellen.
EM00136061 rev. 2.1 1
Panel de control – TEKNA TPG
Acceso al menú de programación.
Durante el funcionamiento de la bomba: Si se pulsa visualiza cíclicamente en el display los valores
programados; si se pulsa simultáneamente a las teclas aumenta o disminuye un valordependiente del modo de funcionamiento escogido. En programación ejerce la función “enter”, esdecir, confirma la entrada de los diferentes niveles del menú y las modificaciones en el interior de losmismos.
Pone en marcha y detiene la bomba. En condiciones de alarma de nivel (sólo función de alarma), dealarma de flujo y alarma memory activas, desactiva la señalización en el display.
Para “salir” de los diferentes niveles del menú. Antes de salir definitivamente de laprogramación se accede a la solicitud de memorización de las modificaciones.
Desplaza los menús hacia arriba o aumenta los valores numéricos a modificar. En modo Batchpuede poner en marcha la dosificación.
Desplaza los menús hacia abajo o disminuye los valores numéricos a modificar.
Led verde parpadeante durante la dosificación.
Led rojo que se enciende durante las diferentes situaciones de alarma.
Conexiones eléctricas
1
2Relé de Alarma
3 Pole +
4 Pole -
Entrada señal 4-20 mAImpedancia De Entrada:200 ohm
5
6
-Entrada control externo (start-stop)-Entrada señal de pausa
7
8
-Entrada señal en frecuencia(contador emisor de impulsos)-Entrada trigger externo
9
10Entrada sensor de Flujo
B Entrada sonda de nivel
B
EM00136061 rev. 2.1 2
Menú de programación Tekna TPG
Pulsando la tecla durante más de tres segundos se accede a la programación. Con las teclas se
pueden desplazar las voces del menú, con la tecla se accede a las modificaciones. En la fábrica la bombase programa en modo constante. La bomba vuelve automáticamente al modo de funcionamiento después de 1
minuto de inactividad. En este caso los datos que se han introducido no serán memorizados. Con la tecla sesale de los niveles de la programación. Al salir de la programación el display visualiza:
Exit Exit
No Save
Save para confirmar la elección
+-
+-
+-Párrafo 1
Párrafo 10
Párrafo 11
Párrafo 12
Párrafo 13Párrafo 14
Párrafo 15
Párrafo 16
Párrafo 9
Párrafo 2
Párrafo 3
Párrafo 4
Párrafo 5
Párrafo 6
Párrafo 7
Párrafo 8
PROG
Configuracion
Funciones Bomba
Funciones Bomba
Caudal maximo
Rele Alarma
Funciones Bomba
Funciones Bomba
Funciones Bomba
Funciones Bomba
Temporizacion
Modo ppm
Modo Batch
Divisor (n:1)
Multiplic.(1:n)
Funciones Bomba
Funciones Bomba
Funciones Bomba
Configuracion
Calib. Bomba
Unidades
StatisticasHoras= ###,##
Caudal Off
Nivel Off
Alarmas
Alarmas
0,23 cc/imp
Idioma
Espagnol
Abierto
Menúprincipal
Menúde ajustes
Menúde funciones
Párrafo 17PausN.Abierto
EM00136061 rev. 2.1 3
Programación del idiomaProgramación Funcionamiento
-
-
-
- -
Pump Functions
Max flow rate
Alarm Relay
Language
P100%
N.Open
English
PROG
+-
Permite seleccionar el idioma, en la fábrica la bomba se
programa en inglés. Pulsando la tecla se accede a la
modificación, con las teclas se programa el valor.
Con la tecla se confirma y se vuelve al menú principal.
Párrafo 1 – Dosificación manualProgramación Funcionamiento
+-
PROG
Manual
Configuracion
ConfiguracionFunciones Bomba
Funciones Bomba
La bomba trabaja en modo constante. El caudal se regula manualmente
pulsando simultáneamente las teclas para aumentarlo o las
teclas para disminuirlo.
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
MAN FFFLev Stop P100%
Modo de funcionamiento Man = Manual
Alarmas y estados Liv = Alarma de nivel Fls = Alarma de flujo
Estado delsensor deFLUJO
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de la dosificación encurso
(depende de la unidad demedida seleccionada)
Porcentaje, Frecuencia,l/h, Gph, ml/m
F320s/mP100%
Modo de funcionamiento Visualiza el valor correspondiente de la
frecuencia
Valor de la dosificación en curso Modifica el caudal máximo pulsando
simultáneamente las teclas + o -
Párrafo 2 – Dosificación Proporcional con señal 0/4-20 mAProgramación Funcionamiento
+-
-
-
+-
+-
0/4 - 20 mA
0/4 - 20 mA
0/4 - 20 mA
Bajo 4.0mA
Alto 20.0mA
PROG
Configuracion
ConfiguracionFunciones Bomba
Funciones Bomba
La bomba dosifica proporcionalmente al recibir una señal (0) 4-20 mA.Según su programación de fábrica, la bomba interrumpe la dosificación a4 mA y dosifica a la máxima frecuencia programada cuando recibe 20mA. En programación se pueden modificar estos dos valores. Lafrecuencia máxima se puede modificar durante el funcionamiento
pulsando simultáneamente las teclas para aumentar el caudal o
las teclas para disminuirlo.
EM00136061 rev. 2.1 4
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
mA FFF 4-20Lev Stop P100%
Modo de funcionamiento mA
Alarmas y estados Lev = Alarma de nivel Flw = Alarma de flujo
Estado delsensor deFLUJO
Valor programado Valor de intervalo
programado (default: 4-20)
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de la dosificación encurso
(depende de la unidad demedida seleccionada)
Porcentaje, Frecuencia,l/h, Gph, ml/m
Low 00.0 mA P100%
Modo de funcionamiento Visualiza en secuencia el
valor de Low y High
Valor mA enentrada
Valor de dosificación en curso Permite modificar el valor máximo
de dosificación pulsandosimultáneamente las teclas + o -
Párrafo 3 – Dosificación Proporcional con señal 20-4/0 mAProgramación Funcionamiento
+-
-
-
+-
+-
20-4/0 mA
Bajo 20.0mA
Alto 4.0mA
PROG
20-4/0 mA
20-4/0 mA
Configuracion
ConfiguracionFunciones Bomba
Funciones Bomba
La bomba dosifica proporcionalmente al recibir una señal 20-4 (0) mA.Según su programación de fábrica, la bomba interrumpe la dosificación a20 mA y dosifica a la máxima frecuencia programada cuando recibe 4mA. En programación es posible modificar estos valores. La frecuenciamáxima se puede modificar durante el funcionamiento pulsando
simultáneamente las teclas para aumentar el caudal o las teclas
para disminuirlo.
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
mA FFF 20-4Lev Stop P100%
Modo de funcionamiento mA
Alarmas y estados Lev = Alarma de nivel Flw = Alarma de flujo
Estado del sensorde FLUJO
Valor programado Valor intervalo programado
(default: 20-4)
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de la dosificación en curso(depende de la unidad de medidaseleccionada)
Porcentaje, Frecuencia, l/h,Gph, ml/m
High 00.0 mA P100%
Modo de funcionamiento Visualiza en secuencia el
valor de Low y High
Valor mA enentrada
Valor de la dosificación en curso
Permite modificar el máximo valor de dosificaciónpulsando simultáneamente las teclas + o -
Párrafo 4 – Proporcional con impulsos externos (multiplicación)Programación Funcionamiento
+-
-
-
-
+-
+-
+-
Multiplic.(1:n)
n 4
Tiempo max 0s
Memoria Off
PROG
Multiplic.(1:n)
Multiplic.(1:n)
Multiplic.(1:n)
Configuracion
ConfiguracionFunciones Bomba
Funciones Bomba
La bomba dosifica proporcionalmente al recibir una señal externa(ejemplo: contador lanza impulsos). A cada señal recibida la bombarealiza los “n” golpes programados. La bomba programa automáticamentela frecuencia de la dosificación, adaptándola al tiempo que transcurreentre dos señales sucesivas. Es posible programar en segundos eltiempo (time out) más allá del cual la bomba pone en cero el conteo delintervalo, para evitar dosificaciones en tiempos demasiado largos. Labomba dispone de la función memory que señala el recibimiento de unaseñal durante la dosificación. Si está programada en OFF se limita aseñalar, si está programada en ON señala y memoriza los impulsos y losejecuta cuando termina de recibir señales.El valor de “n” se puede modificar durante el funcionamiento pulsando
simultáneamente las teclas para aumentar el valor del caudal o
las teclas para disminuirlo.
EM00136061 rev. 2.1 5
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
1:n FFF MMM 1Lev Stop 0
Modo de funcionamiento 1:n = multiplicación
de los impulsos
Alarmas e estados Liv = Alarma de nivel Fls = Alarma de flujo Mem = Alarma Memory
Estado delsensor deFLUJO Valor de n
programado
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de ladosificación en curso Visualiza count-
down de losgolpes
EstadofunciónMemory
Timeout n0s 1
Visualiza el timeoutprogramado
Valor de la dosificación en curso visualiza el valor de n,
pulsando simultáneamente lasteclas + o – se puedemodificar
Párrafo 5 – Proporcional con impulsos externos (división)Programación Funcionamiento
+-
-+-
Divisor (n:1)
n 4
PROG
Divisor (n:1)
Configuracion
Configuracion
Funciones Bomba
Funciones Bomba
La bomba dosifica proporcionalmente al recibir una señal externa(ejemplo: contador lanza impulsos). A cada “n” señales recibidas labomba realiza un golpe. En programación se programa el valor de “n”.Programando el valor de “n” se programa el % de máxima dosificación,durante el funcionamiento se puede modificar este valor pulsando
simultáneamente las teclas para aumentarlo o las teclas
para disminuirlo.
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
N:1 FFF 4Lev Stop P100%
Modo de funcionamiento 1:n = multiplicación
de los impulsos
Alarmas y estados Liv = Alarma de nivel Fls = Alarma de flujo
Estado delsensor deFLUJO
Valor de nprogramado
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de ladosificación en curso Porcentaje máxima
dosificación
n:1 66 P100%
Modo de funcionamiento
Valor programado Valor de n
Valor de la dosificación en curso Modifica del % de la dosificación
pulsando simultáneamente las teclas+ o -
Valor de “n”efectivo
Párrafo 6 – Proporcional con impulsos externos (dosificación Batch)Programación Funcionamiento
+-
-
-
-
+-
+-
+-
Modo Batch(1:c)
Cantidad 10.0ml
Tiempo 10s
Memoria Off
PROG
Modo Batch (1:c)
Modo Batch (1:c)
Modo Batch (1:c)
Configuracion
ConfiguracionFunciones Bomba
Funciones Bomba
La bomba dosifica proporcionalmente al recibir una señal externa(ejemplo: contador lanza impulsos). En este caso se puedeprogramar la cantidad a dosificar en ml y el tiempo para terminar ladosificación. Es posible poner en marca la dosificación manualmente
pulsando la tecla o con un mando remoto. La teclainterrumpe la dosificación que se puede poner en cero pulsando la
tecla o se puede volver a poner en marcha pulsando otra vez la
tecla .La cantidad a dosificar se puede modificar durante el funcionamiento
pulsando simultáneamente las teclas para aumentar el
caudal o las teclas para disminuirlo.
EM00136061 rev. 2.1 6
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
Batch FFF MMM 7.0mlLev Stop 0
Modo de funcionamiento Batch
Alarmas y estados Lev = Alarma de nivel Flw = Alarma de flujo Mem = Alarma Memory
Estado delsensor deFLUJO Valor programado
Cantidad en ml
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de la dosificaciónen curso Visualiza paso a
paso la cantidaddosificada
EstadofunciónMemory
Q.ty 7.0ml7.0ml
Modo de funcionamiento Visualiza en secuencia: La cantidad
a dosificar, el tiempo de ladosificación y la frecuencia de labomba
Valor de la dosificación Modifica la cantidad, pulsando
simultáneamente las teclas + o -
Párrafo 7 – Proporcional con impulsos externos (dosificación en ppm)Programación Funcionamiento
+-
-
-
-
-
+-
+-+-
+-
+-
+-
Modo ppm
ppm 50
puklsos/l 4 pulsos/l 4
l/pulsos 4
Conc(%) 100
Memoria Off
PROG
Modo ppm
Modo ppm Modo ppm
Modo ppm
Modo ppm
Modo ppm
Configuracion
ConfiguracionFunciones Bomba
Funciones Bomba
La bomba dosifica proporcionalmente al recibir una señalexterna (ejemplo: contador lanza impulsos) calculandoautomáticamente la relación entre las señales en entrada ylos golpes de la bomba en función del valor de ppmprogramado. Los datos que se deben introducir son el valorde ppm, la relación impulsos/litro (o litros/impulso) delcontador y la concentración del producto a dosificar. Duranteel funcionamiento se puede modificar la frecuencia de la
dosificación pulsando simultáneamente las teclas
para aumentarla o las teclas para disminuirla.
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
Ppm FFF MMM 10Lev Stop F300s/m
Modo de funcionamiento ppm
Alarnas y estados Liv = Alarma de nivel Fls = Alarma de flujo Mem = Alarma Memory
Estado delsensor deFLUJO Valor de ppm
programado
Estado de la bomba Vacío = bomba en start Stop = bomba parada Pausa = bomba en pausa
Valor de ladosificación en curso Frecuencia
EstadofunciónMemory
cc/stroke 1.00.23 F300s/m
Modo de funcionamiento Visualiza en secuencia:
cc/golpe, impulsos/minuto delcontador y la concentración% del producto químico
Valor de la dosificación Valor de ppm
programado
Valor de la frecuencia dedosificación, pulsandosimultáneamente las teclas+ o – se puede modificar.
EM00136061 rev. 2.1 7
Párrafo 8 – Dosificación temporizada (Entrada señal de frecuencia “TRIGGER” activada)Programación Funcionamiento
+-
-
-
-
+-
+-
+-
Tiempo
Quantidade 100ml
Retardo 0.01.50
Interval 0.01.50
PROG
Tempo
Tiempo g.hh.mm
Tiempo g.hh.mm
Configuracion
Funciones Bomba
Configuracion
Funciones Bomba
-
-
Modo Trigger
Entr. modo pausa
-Modo Trigger
-Modo Trigger
Modo Trigger
N. Aberto N. Aberto
N. Fechado
Disabilitado
Modo Trigger
Después de recibir la señal de TRIGGER programada, la bombadosifica una cantidad programable en ml. Es posible programar untiempo de retardo antes de la dosificación (Retardo) y la distanciaentre dosificaciones sucesivas (Interv.) como se ilustra en elesquema:
Por ejemplo, programando un tiempo Interv.= 0 se obtiene unsistema en el que la cantidad programada es dosificada después decada señal de TRIGGER (con el posible retardo programado):
También puede ponerse en marcha la dosificación pulsando la tecla+, que prácticamente simula la señal de Trigger.La señal Trigger puede programarse en N. Aberto (se activa cuandola entrada pasa del modo abierto al cerrado) o en N. Fechado (seactiva cuando la entrada pasa del modo cerrado al abierto).La señal Trigger permanece bloqueada durante la dosificación (surecepción no es memorizada ni gestionada).La entrada Pausa (Entrada mando a distancia) no puede serprogramada y su activación bloquea la dosificación, mientras que lasiguiente desactivación vuelve a poner el sistema en estado deespera de la señal Trigger para efectuar una nueva dosificación.
Durante el funcionamiento de la bomba se puede modificar la
frecuencia de dosificación pulsando simultáneamente las teclas
para aumentar la frecuencia o las teclas paradisminuirla.
Visualización durante el funcionamiento Visualización en programación (tecla MODE)
Timer FFF 7,0 mlStop P 0%
Modalità di funzionamento
Temporizador
Alarmas y estados Liv = Alarma nivel
Flujo = Alarma control deflujo Espera Emisión
Estado sensor deFLUJO
Valor programado
Cantidad en ml
Estado de la bomba
Vacío = bomba enarranque
Stop = bomba en parada
Reiniciar = bomba enrearranquie
Valor de ladosificación en curso
Porcentaje delosgolpes/mín.máx.
Cdad.20,0ml
20,0ml
Modo de funcionamiento Se visualizan en secuencia: cantidad a
dosificar, retardo en d. h. m., eintervalo en d. h. m.
Valor de ladosificación
Cantidadprogramada en ml
Valor del porcentaje dedosificación modificable pulsandolas teclas + o -
Retardo Interv.
CantidadTrigger
Retardo
Trigger
Retardo
Trigger
EM00136061 rev. 2.1 8
Párrafo 8 – Dosificación temporizada (Entrada señal de frecuencia “TRIGGER”no activada)Programación Funcionamiento
+-
-
-
-
+-
+-
+-
Tiempo
Quantita 100ml
Retardo 0.01.50
Interval 0.01.50
PROG
Tiempo
Tiempo g.hh.mm
Tiempo g.hh.mm
Configuracion
Funciones Bomba
Configuracion
Funciones Bomba
-
-
Modo Trigger
Entr. modo pausa
Disabilitado
Restart Temp
+-
-Entr. modo pausaRestart Temp
-Entr. modo pausaBloquea tiempo
Entr. modo pausaPausa dosif.
La bomba dosifica una cantidad que se puedeprogramar en ml; se puede programar un tiempo deretardo para la puesta en marcha de la bomba(Retardo) y la distancia entre dos dosificacionessucesivas (Interv.), como se muestra en el esquema:
Los tiempos de Retardo y de Interv son en d.h.m.(días, horas, minutos).
La entrada de la Pausa puede programarse de tresmodos distintos:
1. Bloquea tiempo: con la pausa activada, elsistema bloquea el conteo del tiempo actual ylo reanuda cuando se desactiva la pausa.
2. Pausa dosificación: con la pausa activada,el sistema sigue contando el tiempo ybloquea la dosificación
3. Restart temp: con la pausa activada, elsistema bloquea la dosificación y aldesactivarse la pausa el conteo empieza denuevo desde el principio.
Durante el funcionamiento de la bomba se puedemodificar la frecuencia de dosificación pulsando
simultáneamente las teclas para aumentar
la frecuencia o las teclas para disminuirla.
Visualización durante el funcionamientoVisualización en programación (tecla
MODE)
Timer FFF 7,0 mlLiv Stop P 0%
Modo de funcionamiento
Temporizador
Alarmas y estados Niv =Alarmas nivel
Flujo = Alarma controlde flujo
Estadosensor deFLUJO
Valor programado Cantidad en ml
Estado de la bomba Vacío = bomba en start Stop = bomba en parada Reiniciar = bomba en
rearranque
Valor de ladosificación en curso
Porcentaje delos golpes/min.máx
Q.tà 20,0ml20,0ml P 100%
Modo de funcionamiento
Se visualizan en secuencia:cantidad a dosificar, retardo end. h. m., e intervalo en d. h. m.
Valor de ladosificación
Cantidadprogramada enml
Valor del porcentaje dedosificación modificable pulsandolas teclas + o -
Retardo Interv.
Cantidad
EM00136061 rev. 2.1 9
Párrafo 9 – Programación del caudal máximoProgramación Funcionamiento
-
--
P100% P100%
F320s/m
PROG
-+-
+-
Configuracion
ConfiguracionFunciones Bomba
Caudal maximo Caudal maximo
Caudal maximo
Permite programar el caudal máximo que la bomba puedealcanzar; el modo programado (% o frecuencia) se vuelve lavisualización del caudal en la unidad de medida estándar.
Pulsando la tecla se accede a la modificación,
después con las teclas se programa el valor. Con
la tecla se confirma y se vuelve al menú principal.
Párrafo 10 – Programación del relé de alarmaProgramación Funcionamiento
-
-
- -
Funzioni Pompa
Caudal maximo
Rele alarma
P100%
Abierto
PROG
+-
Configuracion
Configuracion
En ausencia de una situación de alarma se puedeprogramar abierto (fábrica) o cerrado. Pulsando la tecla
se accede a la modificación, después con las teclas
se programa el valor. Con la tecla seconfirma y se vuelve al menú principal.
Párrafo 11 – Calibración del caudalProgramación Funcionamiento
-
-
-
-
Calib. Bomba
Cal. Manual
Cal. Automatica
Cal. Automatica
Cal. Automatica
0,23 cc/colpo
cc/impulso 0,23
inicio 100 imp.
Inyecciones 100
ml 20
Manual
PROG
+-
+-
Automatica
Configuracion
Calib. Bomba
Calib. Bomba
En el menú principal aparece el valor de cc por golpe enmemoria. Se puede calibrar en dos modos:MANUAL – Introduciendo manualmente el valor de cc cada
golpe con las teclas y confirmando con la tecla
.AUTOMÁTICA – La bomba realiza 100 golpes, poner en
marcha y confirmar con la tecla al final introducir la
cantidad aspirada por la bomba con las teclas y
confirmar con la tecla . El dato introducido seráutilizado en los cálculos de los caudales.
Párrafo 12 – StadísticasProgramación Funcionamiento
-
-
-
-
-
-
Statisticas
Statisticas
Reset Estat.
Horas 10
Horas 10
Inyecciones 1000
NO
PROG
+-
Cant.(l) 100
Arranques 10
Reset
ESC
Configuracion
Statisticas
Statisticas
Statisticas
Statisticas
En el menú principal visualiza las horas de funcionamiento
de la bomba, pulsando la tecla se accede a las demásestadísticas:- Strokes = Número de golpes realizados por la bomba.- Q.ty (L) = Cantidad dosificada por la bomba expresada enlitros; este valor se calcula en base al valor cc/stroke enmemoria.- Power = Número de puestas en marcha de la bomba.
- Reset = Con las teclas se pueden poner en cero
(YES) o no (NO) los contadores, con la tecla se
confirma. Pulsando la tecla se vuelve al menúprincipal.
EM00136061 rev. 2.1 10
Párrafo 13 - PasswordProgramación Funcionamiento
-
-
-
Password
Password
****
0000
PROG
+ -
ConfiguracionIntroduciendo la password se puede entrar en programacióny ver todos los valores programados, pero cada vez que sequieran modificar será solicitada la password. La líneaparpadeante indica el número que se puede modificar, con
la tecla se selecciona el número (de 1 a 9), con la tecla
se selecciona el número a modificar y con la tecla
se confirma. Programando “0000” (fábrica) lapassword queda excluida.
Párrafo 14 – Alarma de flujoProgramación Funcionamiento
-
-Alarma
Alarma
Alarma Caudal
Alarma Caudal
Alarma Caudal-On
Caudal Off
Caudal Off
Off
On
Segnales 6
PROG
+
+
-
--
-
-
ESC
Configuracion
Permite activar (desactivar) el sensor de flujo. Una vez
activado (ON) pulsando la tecla se accede a la solicitudde cuántas señales espera la bomba antes de entrar en
alarma. Pulsando la tecla el número parpadea, con las
teclas se puede programar el valor. Con la tecla
se confirma. Pulsando la tecla se vuelve al menúprincipal.
Párrafo 15 – Alarma de nivelProgramación Funcionamiento
-
-Alarma Nivel
Alarma Nivel
AlarmaNivel Stop
Nivel Alarma
Stop
Alarma
Alarma
PROG
-
-
-ESC
Configuracion
Permite programar la bomba cuando se activa la alarma delsensor de nivel, es decir se bloquea la dosificación (Stop) osimplemente activa la señal de alarma sin bloquear la
dosificación. Pulsando la tecla se accede a la
modificación, con las teclas se puede programar el
tipo de alarma. Con la tecla se confirma. Pulsando la
tecla se vuelve al menú principal.
Párrafo 16 – Unidad de visualización del caudalProgramación Funcionamiento
-
-Unidades Unidades
Unidades
Standard Standard
EM00136061 rev. 2.1 11
Párrafo 17 - Programación PausaProgramación Funcionamiento
- -PausN.Abierto
PROG
+-
Configuracion
+
Entrada esterna de paro de bomba.De fábrica el sistema llega configurado como NormalmenteAbierto.
Pulsando la tecla se accede a la modificación,
después con las teclas se programa el valor ( N.ABIERTO o N. CERRADO.)
Con la tecla se confirma y se vuelve al menúprincipal.
Ajuste contraste display
Para ajustar el contraste del display mantener presionada la tecla y dentro de 5 segundos presionar las
teclas o para aumentar o disminuir el contraste
AlarmasVisualización Causa Interrupción
Led Alarma fijoMensaje Lev parpadeanteEj: Man
Lev P100%
Alarma de final del nivel sininterrupción del funcionamiento dela bomba.
Reestablecer el nivel del líquido.
Led Alarma fijoMensajes Lev y stop parpadeantesEj: Man
Lev Stop P100%
Alarma final del nivel coninterrupción del funcionamiento dela bomba.
Reestablecer el nivel del líquido.
Mensaje Mem parpadeanteEj: 1:n 6
Mem
La bomba recibe uno o másimpulsos durante la dosificación conla función memory en OFF.
Pulsar la tecla
Mensaje Mem parpadeanteEj: 1:n M 6
Mem
La bomba recibe uno o másimpulsos durante la dosificación conla función memory en ON.
Cuando la bomba termina derecibir los impulsos externosdevuelve los golpes memorizados.
Led Alarma fijoMensaje Flw parpadeanteEj: Man F
Flw P100%
Alarma de flujo activa, la bomba noha recibido el número de señalesprogramadas por el sensor de flujo.
Pulsar la tecla
Ej: Parameter ErrorPROG to default
Error de comunicación interna de laCPU. Pulsar la tecla para
reestablecer los parámetros dedefault.
EM00136061 rev. 2.1 1
Panneau de contrôle – TEKNA TPG
Accès au menu de programmation
Pendant la phase de fonctionnement de la pompe: si cette touche est enfoncée elle affiche à desintervalles réguliers les valeurs programmées; si elle est enfoncée en même temps que les touches
elle augmente ou réduit une valeur dépendant du mode de fonctionnement choisi. Au coursde la programmation, elle fait fonction de “enter”, c’est-à-dire qu’elle confirme l’entrée dans lesdifférents niveaux de menu et les modifications à l’intérieur de ces derniers.
Fait démarrer et met à l’arrêt la pompe. Dans les conditions d’alarme de niveau (unique fonctiond’alarme), de flux et de mémoires actives, elle désactive la signalisation sur l’afficheur.
Pour “quitter” ces différents niveaux de menu. Avant de quitter définitivement la programmation, onaccède à la demande d’enregistrement des modifications
Fait défiler les menus vers le haut ou augmente les valeurs numériques à modifier. En mode defonctionnement Batch, elle peut faire démarrer le dosage.
Fait défiler les menus vers le bas, ou réduit les valeurs numériques à modifier.
Led verte clignotante pendant le dosage.
Led rouge qui s’allume dans les différentes situations d’alarme.
Connexions électriques
1
2
Relais Alarme
3 Pole +
4 Pole -
Entrée signal 4-20 mAImpédance D'Entrée: 200ohm
5
6
-Entrée commande à distance(start-stop)-Entrée Pausa signal
7
8
-Entrée signal fréquence (compteurémetteur d’impulsions)-Entrée Detente externo
9
10Entrée capteur de débit
B Entrée sonde de niveau
B
EM00136061 rev. 2.1 2
Menu de programmation Tekna TPG
Appuyer sur la touche pendant plus de trois secondes pour allumer la programmation. Avec les touches
il est possible de faire défiler les options du menu, la touche permet d’accéder aux modifications.La pompe est programmée en usine en mode constant. La pompe reprend automatiquement le mode defonctionnement après 1 minute de non-activité. Dans ce cas, les données éventuellement introduites ne sont pas
enregistrées. La touche permet de quitter les niveaux de la programmation. À la sortie de la programmation,l’afficheur visualise :
Exit ExitNo Save
Save Pour confirmer le choix
+-
+-Pompe fonctionsConfiguration
+-Paragraphe 1
Paragraphe 10
Paragraphe 11
Paragraphe 12
Paragraphe 13
Paragraphe 14
Paragraphe 15
Paragraphe 16
Paragraphe 9
Paragraphe 2
Paragraphe 3
Paragraphe 4
Paragraphe 5
Paragraphe 6
Paragraphe 7
Paragraphe 8
PROG
Temp
Manuel
Multiple (1:n)
Divise (n:1)
Mode ppm
Batch (1:c)
Debit max
Contact alarmeNO
Pompe fonctions
Pompe fonctions
Pompe fonctions
Pompe fonctions
Pompe fonctions
Pompe fonctions
Pompe fonctions
Pompe fonctions
Pompe calib.0.23 cc/coup
Unite
Alarme
Alarme
Niveau Stop
Debit Off
Menufonction
Menuréglage
MenuprincipalStatistiques
Code d'acces
Heures
Francais
Langage
Paragraphe 17PausN.Ouvert
EM00136061 rev. 2.1 3
Programmation de la langueProgrammation Fonctionnement
-
-
-
- -
Pump Functions
Max flow rate
Alarm Relay
Language
P100%
N.Open
English
PROG
+-
Permet de sélectionner la langue, la pompe est programméeen usine en anglais.
Appuyer sur pour accéder à la modification, puis sur
les touches pour programmer la valeur. La touche
confirme et permet de retourner au menu principal.
Paragraphe 1 –Dosage manuelProgrammation Fonctionnement
+-
Configuration
PROG
Fonctions pompe
Fonctions pompe
Manuel
La pompe travaille en mode constant et le débit peut être réglé uniquement
en mode manuel en appuyant simultanément sur les touches
pour augmenter le débit ou sur les touches pour le réduire.
Affichage pendant le fonctionnementAffichage lors de la programmation (touche
MODE)
MAN FFFNiv Stop P100%
Mode de fonctionnement
Man = Manuelle
Alarmes et états
Niv = Alarme niveau
Deb = Alarme flux
État capteur deFLUX
État de la pompe Vide= pompe au
démarrage
Stop = pompe arrêtée
Paus = pompe en pause
Valeur du dosage en cours(dépend de l’unité de mesure
sélectionnée)
Pourcentage, Fréquence,l/h, Gph, ml/m F320s/m
P100%
Mode de fonctionnement Affiche la valeur correspondante de la
fréquence
Valeur du dosage en cours Modification du débit maximal en
appuyant en même temps sur + ou -
Paragraphe 2 – Dosage Proportionnel sur signal 0/4-20 mAProgrammation Fonctionnement
+-
-
-
+-
+-
0/4 - 20 mA
0/4 - 20 mA
0/4 - 20 mA
Bas 4.0mA
Haut 20.0mA
PROG
Fonctions pompe
Fonctions pompe
Configuration La pompe dose proportionnellement sur un signal (0)4-20 mA. Laprogrammation d’usine de la pompe prévoit l’interruption du dosage à 4mA et le dosage à la fréquence maximale programmée lorsqu’elle reçoit20 mA. En cours de programmation, il est possible de modifier ces deuxvaleurs. La fréquence maximale est modifiable pendant le fonctionnement
en appuyant simultanément sur les touches pour augmenter le
débit ou sur les touches pour le réduire.
EM00136061 rev. 2.1 4
Affichage pendant le fonctionnementAffichage lors de la programmation (touche
MODE)
mA FFF 4-20Lev Stop P100%
Mode de fonctionnement
mA
Alarmes et états
Niv = Alarme niveau
Deb = Alarme flux
État capteur deFLUX
Valeur programmée Valeur intervalle
programmée (défaut : 4-20)
État de la pompe Vide= pompe au démarrage
Stop = pompe arrêtée
Paus = pompe en pause
Valeur du dosage en cours(dépend de l’unité de mesure
sélectionnée)
Pourcentage, Fréquencel/h, Gph, ml/m
Bas 00.0 mA P100%
Mode de fonctionnement Affiche dans l’ordre la
valeur de Bas et Haut
Valeur mAen entrée
Valeur du dosage en cours Permet de modifier la valeur
maximale de dosage en appuyanten même temps sur e + ou -
Paragraphe 3 – Dosage proportionnel sur signal 20-4/0 mAProgrammation Fonctionnement
+-
-
-
+-
+-
20-4/0 mA
Bas 20.0mA
Haut 4.0mA
PROG
20-4/0 mA
20-4/0 mA
Fonctions pompe
Fonctions pompe
Configuration La pompe dose proportionnellement sur un signal 20-4 (0) mA. Laprogrammation d’usine de la pompe prévoit l’interruption du dosage à 20mA et le dosage à la fréquence maximale programmée lorsqu’elle reçoit 4mA. En cours de programmation, il est possible de modifier ces deuxvaleurs. La fréquence maximale est modifiable pendant le fonctionnement
en appuyant simultanément sur les touches pour augmenter le
débit ou sur les touches pour le réduire.
Affichage pendant le FonctionnementAffichage lors de la programmation (touche
MODE)
mA FFF 20-4Lev Stop P100%
Mode de fonctionnement mA
Alarmes et états
Niv = Alarme niveau
Deb = Alarme flux
État capteur deFLUX
Valeur programmée Valeur intervalle
programmée (défaut: 20-4)
État de la pompe
Vide=pompe au démarrage
Stop = pompe arrêtée
Paus = pomp