Clearwater 11577 U.S. Highway 19N

Clearwater, FL 33764 Tel: (727) 572-8255 Fax: (727) 573-1604

Tampa 4720 E. Adamo Drive

Tampa, FL 33605 Tel: (813) 877-8253 Fax: (813) 876-4778

Sarasota 2224 72nd Terrace East

Sarasota, FL 34243 Tel: (941) 360-0010 Fax: (941) 358-0032

Hudson 16520 Scheer Blvd. Hudson, FL 34667 Tel: (727) 245-1320 Fax: (727) 245-1321

Naples 544 Commercial Blvd.

Naples, FL 34104 Tel: (239) 384-5400 Fax: (239) 384-5401

Fort Myers 6461 Topaz Court

Fort Myers, FL 33966 Tel: (239) 275-9577 Fax: (239) 278-5502

Installation Solutions 2016 Edition

2

Table of Contents Ductboard……………………..………..……………………………………………..…3

Duct Liner……………………….…….……...…………………………..…….....3

Duct Wrap……………………….…….……………………..……………..……..3

Flex Duct……………………………....………….…………………….………………..4

Mobile Home Duct……………..………….…………....……...……………….....5

Duct Washers…….………….………….……..……….……...……………….....5

Prefab Boxes and Plenums….……….………..…….………...……………….....5

Strut Systems…………………………..…………………..…………………………..6

Unistrut…………………………….….………………...……...……………….....6

Slotted Angle…….…………………...……...………………………………….....7

Threaded Rod….……………….…….…...….……………………..………….....7

Cush & Beam Clamps….……………..………………………..……………….....7

Metal Products…………………...…...………………………………………………..8

Boots, Collars & Dampers……..…...……...………………………..………….....8

Canstock, Bootrail & Heat Shield..……...…...………………………………….....8

Metal Pipe & Connectors…………..…….…...………………………………….....8

Roof Vents, Exhaust Vents & Line Jacks………………….…...……………….....9

Grilles & Diffusers……………………………………...……………….…………..10

Commercial Lay-In Products………...……...…………………...…………........10

Ceiling Supply Grilles…….…...…………………………………..………..….....11

Register Screws…………….………………………..……...……………..….....11

Sidewall Grilles….……………………………………….…...……………….....12

Return Grilles…………………………………………….…...……………….....12

Air Handler Mounting.………………………….……...…………..………………..13

Drain Pans………..……...…………………………..……………….……….....13

Hanging Kits……………………………………………..…...……………….....13

Air Handler Stands & Coffin Boxes……….…………………..……………….....13

Condenser Mounting………...………………….……...…………………………..14

Condenser Pads………..……...……………………………………..……….....14

Roof Stands & Wall Brackets…………………………..…...……..………….....14

Tie Down Kits…………….…………………………………..………….…….....15

Vibration Pads & Isolators….………………..……………...…………..…….....15

Duct Hanging Products…………………...………………………………………..16

Tapes & Adhesives…………..………………….…...…………………………..16

Mastics…………….…………..………………….…...…………………………..17

Electrical Whips & Disconnects……….……..……...…………………………..17

Thermostat Wire & Premade Linesets……..…......…………………………..18

ACR & Soft Copper Tubing…..…......……………………..……………………..18

Copper Fittings & Flares………….…………...…………………………………..19

Tubing Insulation…………………...……………………………….…...…………..20

Metal Linecovers……...………………...………………….…...………….………..21

Fortress Linecovers………………….…………………….…...………….………..21

Condensate Products…………………...………………………………...………..22

PVC Pipe Fittings & Glue………....……...……………………..…………….....22

Pipe Prop Stands…….…...…………..……………………………………….....22

Condensate Switches…………….…………...……………...……………….....23

Condensate Pumps….………..………...…………………………………….....23

Ductless Condensate Pumps….………...…………………………………….....23

3

Ductboard Mat-Faced Micro-Aire®

Type 475 & Type 800

Durable Airstream Surface. Mat-Faced Micro-Aire exhibits superior toughness compared to standard fiber glass duct board. It provides increased resistance to damage that can occur from in-shop handling, fabrication, jobsite shipping, and installation.

“Friendlier Feel”. The smooth mat facing creates a friendlier surface for fabrication and installation, and reduces exposure to normal construction dust.

Quiet Operation. Fabricated Mat-Faced Micro-Aire duct systems noticeably decrease the audibility of crosstalk, equipment noise, and eliminates the sounds associated with the expansion and contraction of sheet metal duct systems.

Will Not Support Microbial Growth. Treated with an EPA-registered antimicrobial agent for HVAC applications to resist potential growth of fungus or bacteria on the airstream surface.

By the Case Boards Per Carton Item # Board Type Size

DUCTBOARD-R4.2-CASE 475 MF (R4.2) 1" x 4' x 10' 6 DUCTBOARD-R6-CASE 800 MF (R6) 1.5" x 4' x 10' 4 DUCTBOARD-R8-CASE 800 MF (R8) 2" x 4' x 10' 3

By the Pallet Boards Per Pallet Item # Board Type Size

DUCTBOARD-R4.2-SHEET 475 MF (R4.2) 1" x 4' x 10' 44 DUCTBOARD-R6-SHEET 800 MF (R6) 1.5" x 4' x 10' 30 DUCTBOARD-R8-SHEET 800 MF (R8) 2" x 4' x 10' 22

Duct Liner

Spiracoustic Plus™ duct liner is specifically engineered to provide very high acoustical & thermal performance in round air ducts of virtually any size. Spiracoustic Plus duct liner has factory-made, evenly spaced kerfs to allow the material to conform to the inside diameter of round air ducts.

Please call for a detailed quote!

Standard Size - Many Others Available! Item Number Size

DUCTLINER-1X48X100 1" x 48" x 100"

Duct Wrap Microlite EQ Formaldehyde-free™ duct wrap insulation is a brown, lightweight, highly resilient, blanket-type thermal insulation. The insulation blanket is manufactured from rotary-process fiberglass bonded with a resin made primarily from rapidly renewable plant-based materials.

Available Forms. Microlite EQ Formaldehyde-free™ insulation is available in a variety of densities, thicknesses and roll lengths. It is supplied with an FSK (foil-scrim-kraft) vapor barrier facing to meet installed performance requirements, with a 2" (51 mm) stapling tab.

Uses. Microlite EQ insulation is recommended as thermal insulation for the exterior of HVAC systems or other spaces or surfaces where temperature control is required.

Item Number Size Sq. Ft. per Roll Installed R-Value DUCTWRAP-2.33X48X75 2.33" x 48" x 75' 300 sq. ft. R6.5

Linacoustic RC insulation is a flexible duct liner made from strong, glass fibers bonded with a thermosetting resin. The airstream surface is protected with exclusive Reinforced Coating system, combining state-of-the-art Permacote® acrylic coating with a flexible glass mat reinforcement to provide a smooth airstream surface.

Will Not Support Microbial Growth. Formulated with an immobilized EPA-registered protective agent to protect the coating from potential growth of fungi and bacteria.

Linacoustic RC Duct Liner Notes: Linacoustic RC duct liner is available in widths between

34"–36", 46"–48" and 56"–61" in ¼" increments. Non-stock widths require a minimum special order quantity (includes widths to fit 6' coil line ducts) and may require up to four weeks lead time.

Special roll lengths to 200' are available in some thicknesses and widths. Non-stock sizes require a minimum special order quantity and may require up to four weeks lead time.

Many more sizes and styles available – please consult your Trane Supply representative with your needs.

4

Silver Flex 25' Bags Item Number Size R6 R8

4" FLEX-R6-04-SILVER FLEX-R8-04-SILVER

5" FLEX-R6-05-SILVER FLEX-R8-05-SILVER

6" FLEX-R6-06-SILVER FLEX-R8-06-SILVER

7" FLEX-R6-07-SILVER FLEX-R8-07-SILVER

8" FLEX-R6-08-SILVER FLEX-R8-08-SILVER

9" FLEX-R6-09-SILVER FLEX-R8-09-SILVER

10" FLEX-R6-10-SILVER FLEX-R8-10-SILVER

12" FLEX-R6-12-SILVER FLEX-R8-12-SILVER

14" FLEX-R6-14-SILVER FLEX-R8-14-SILVER

16" FLEX-R6-16-SILVER FLEX-R8-16-SILVER

18" FLEX-R6-18-SILVER FLEX-R8-18-SILVER

20" FLEX-R6-20-SILVER FLEX-R8-20-SILVER

Bag Direct Ship Quantities R4.2 R6 R8

Size Skid Layer

Full Skid

Skid Layer

Full Skid

Skid Layer

Full Skid

4" 30 150 25 125 25 125 5" 25 125 25 125 25 125 6" 25 125 20 100 16 80 7" 20 100 16 80 16 80 8" 16 80 16 80 16 80 9" 16 80 12 60 9 45

10" 12 60 9 45 9 45 12" 9 45 9 45 6 30 14" 6 30 6 30 6 30 16" 6 30 6 30 6 30 18" 4 20 4 20 4 20 20" 4 20 4 20 4 20

Flexible Duct Silver Jacket

Gray Flex's models 4GF(R-4.2),4GF-6(R-6.0),and 4GF-8(R-8.0) are tested in accordance with U.L.181 and approved for use as a Class 1 air duct material. Jacketing is printed with certification label, foot markers, size and performance data every 24"-(Foot markers every 12"). It is jacketed with a scrim reinforced metalized polyester vapor barrier. The airtight Core is our exclusive patented, reinforced inner liner. Fiberglass insulation is a minimum of 1 1/4" thick for 4GF, min. of 2" for 4GF-6, and min. of 2 5/8" for 4GF-8.

Mobile home ducts are used primarily as a supply or return duct of a HVAC system of a mobile or modular home. It is jacketed with a heavy duty black polyethylene vapor barrier which meets the HUD requirements for outdoor mobile home or modular home applications.

Mobile Home Flex—25' Boxes Size R4.2 Item # R6 Item #

6" FLEX-MOBILE-R4.2-06 FLEX-MOBILE-R6-06

8" FLEX-MOBILE-R4.2-08 FLEX-MOBILE-R6-08

10" FLEX-MOBILE-R4.2-10 FLEX-MOBILE-R6-10

12" FLEX-MOBILE-R4.2-12 FLEX-MOBILE-R6-12

14" FLEX-MOBILE-R4.2-14 FLEX-MOBILE-R6-14

16" N/A FLEX-MOBILE-R6-16

Mobile Home Flex

Square-to-Round Adapters Item Number Height Width Depth Collar Size Fits PCH181412RCF-2 18.85" 14.42" 6" 12" Round 2.0 - 3.0 Ton 4TCC/4TWC

Package Units PCH181414OCF-2 18.85" 14.42" 6" 14" Oval PCH181914RCF-2 18.85" 19.42" 6" 14" Round 2.0 - 5.0 Ton 4TCC/4TWC

Package Units PCH181916RCF-2 18.85" 19.42" 6" 16" Round

5

Duct Washers

Mixing Boxes Prefab Triangles

Item Number Size TRIANGLE-14X14X12 14" x 14" x 12" TRIANGLE-18X18X18 18" x 18" x 18" TRIANGLE-18X18X24 18" x 18" x 24"

Item Number Pack Qty. ZIP-EZ 250 (bag)

Perfect mixing boxes for multiple duct runs

Duct Accessories Fasteners

Zip-EZ™ all-purpose insulation fasteners are a Plenum-Rated solution. Zip-Ez™ mechanically secures duct wrap and fiber-free reflective insulation using a sheet metal screw. Zip-Ez™ all-purpose fasteners won’t lose bonding properties in extreme hot or cold temperatures.

Prefab Trapezoids Item # Base Top Height

#500-840 18" x 16" 16" x 14" 14" #500-842 20" x 20" 16" x 20" 17" #500-844 24" x 24" 18" x 24" 16"

Item Number Size Pack Qty.

5-SCR82-100 #8 x 2" Taper-Point Sheet Metal Screw 100 (bag) 5-SCR82 #8 x 2" Taper-Point Sheet Metal Screw 350 (jar)

Prefabricated Plenums Interior Exterior Fits

Item # Height Width Depth Width Depth TAM4 GAM5 TAM7/8 GAF2 TEM4 TEM6

#500-850 14.5X18X4 4' 14.5" 18" 17.5" 21" 18-36 18-24 24 18-36 - -

#500-850 18.5X18X4 4' 18.5" 18" 21.5" 21" 42 30-36 30 - - -

#500-850 20.5X18X4 4' 20.5" 18" 23.5" 21" 48-60 42-60 36-60 - - -

#500-850 15.5X17.5X4 4' 15.5" 17.5" 18.5" 20.5" - - - - 18-30 24-30

#500-850 20.5X17.5X4 4' 20.5" 17.5" 23.5" 20.5" - - - - 36-60 36-42 **

#500-850 23.5X17.5X4 4' 23.5" 17.5" 26.5" 20.5" - - - - - 48-60 **

** "D" Model 48 & 60 TEM6 units use the 26.5" wide plenum. "C" Model 48 & 60 TEM6 units use the 23.5" wide plenum.

Perfectly Sized for Your Trane Air Handler! These 4’ long plenum boxes are specifically sized to match the exterior cabinet of your Trane air handler. They ship “knocked down” for easy transportation and storage, but are pre-grooved for rapid assembly. The kit ships complete with endcap, tape and squeegee—everything you need. Perfect for replacing a vertical plenum, or cut it in half for supply and return transitions in a horizontal application.

6

Strut Systems Deep & Shallow Unistrut

Item Number Gauge Style Length UNISTRUT-B22SHGRN10 12ga. Deep (1-5/8") 10' UNISTRUT-B24SHGRN10 14ga. Deep (1-5/8") 10' UNISTRUT-B54SHGRN10 14ga. Shallow (13/16") 10'

Combo Nut Washer

Item # Thread Size NW-528 3/8" x 16

Buzznut Features Easily removed and adjusted Design combines washer & lock nut Reduce installation time by up to 42% Installs anywhere along threaded rod

Eliminates threading hex up the length of the rod Retro-fit without disassembling existing supports

Many more strut system components are available– contact your Trane Supply representative with your needs.

Provides quick attachment for threaded rod Able to install using just one hand Helps reduce overall installation time

Features Combination design reduces the number of parts Serrated flange negates the need for a flat washer Allows for easy adjustment when installed in channel

Spring Nuts/Square Washers Item # Description Box Qty.

BUZZNUT-3/8 Combination Washer/Locknut 100

N228 ZN 3/8" Spring Nut for Deep Strut 100

N528 ZN 3/8" Spring Nut for Shallow Strut 100

N228WO ZN 3/8" Nut for Unistrut - No Spring 100

B201 ZN Square Washer for 3/8” Rod 100

Strut Fittings

B129 ZN B133 ZN

B140 ZN

Item # Description Box Qty. B129 ZN Two-Hole Splice Plate 50 B133 ZN Four-Hole Tee Plate 25 B140 ZN Three-Hole Corner Plate 25

7

Strut Systems Cush-Clamps

Threaded Rod Item Number Size Threads per Inch Length

THREADED-ROD-3/8X6 3/8" 16 6'

Slotted Angle Item Number Gauge Size Length

SLOTTED-ANGLE-10 14ga. 1-5/8" x 1-5/8" 10'

VibraClamp™ Pipe Clamps BVT Series VibraClamp - Copper and O.D.

Safety Factor of 3 Accesses tubing sizes 1/8” (3) to 6” (150) Allows easy one tool installation Endures high (+300°F) and low (-40°F) temps Dampens vibration and noise Eliminates galvanic metal to metal contact Resists most industrial oils and solvents Reduces thermal loss and gain Secures tubing firmly to channel (strut) Dielectric strength of 400 volts/mil Includes cushion, clamp, screw and nut

Item Number Tubing O.D. CUSH-CLAMP-025 1/4" CUSH-CLAMP-037 3/8"

CUSH-CLAMP-050 1/2" CUSH-CLAMP-062 5/8" CUSH-CLAMP-075 3/4" CUSH-CLAMP-087 7/8" CUSH-CLAMP-112 1-1/8" CUSH-CLAMP-137 1-3/8" CUSH-CLAMP-162 1-5/8" CUSH-CLAMP-212 2-1/8"

Beam Clamps & Connectors Item

Number Description Rod Size B C D

Throat Opening

B3033-3/8 Wide Jaw Wedge C-Clamp 3/8" x 16 2-1/4" 2" 1-1/8" 1-1/4"

B3034-3/8 Wedge C-Clamp 3/8" x 16 1-5/8" 2" 7/8" 3/4"

B3058-3/8 Side Beam Connector 3/8" x 16 2-3/8" 9/16" N/A N/A

Beam Clamps Beam Connectors

Item Number Description Pack Qty. B655-3/8 ZN Rod Coupling for 3/8” Rod 100

6503 3/8" Hex Nut 25

6503CX 3/8" Hex Nut 100 6704 3/8" Flat Washers 37

6704-2X 3/8" Flat Washers 134 6733 3/8" Lock Washers 38

AHU Hanging Kit Couplers, Nuts & Washers Item # Contents Qty.

HANGER KIT 3/8" 32” x 14 Gauge Slotted Angles 2 3/8” x 6ft Threaded Rods 4 1/4” x 3” Eye Bolts 4 1/4” x 2” Eye Lag Bolts 4 1/4” Hex Nuts 4 3/8” Hex Nuts 8 5/16” Flat Washers 12 3/8” Fender Washers 4

8

Integrated Box w/ Collar

Insulated Register Boxes Flat-Top Boxes

R6.0 Insulation Foil Top Flanged

Boot w/ Flange Size BOOT-08X04 8" x 4" BOOT-08X06 8" x 6" BOOT-08X08 8" x 8" BOOT-10X06 10" x 6" BOOT-10X08 10" x 8" BOOT-10X10 10" x 10" BOOT-12X06 12" x 6" BOOT-12X08 12" x 8" BOOT-12X12 12" x 12" BOOT-14X06 14" x 6" BOOT-14X08 14" x 8" BOOT-14X14 14" x 14" BOOT-16X16 16" x 16"

Collar Description COLLAR-04 4" Snapped Collar COLLAR-05 5" Snapped Collar COLLAR-06 6" Snapped Collar COLLAR-07 7" Snapped Collar COLLAR-08 8" Snapped Collar COLLAR-09 9" Snapped Collar COLLAR-10 10" Snapped Collar COLLAR-12 12" Snapped Collar COLLAR-14 14" Snapped Collar COLLAR-16 16" Snapped Collar COLLAR-18 18" Snapped Collar COLLAR-20 20" Snapped Collar

Item Number Box Size Collar BOOT-08X04X04 8" x 4" 4" BOOT-08X04X05 8" x 4" 5" BOOT-10X06X06 10" x 6" 6" BOOT-10X06X07 10" x 6" 7" BOOT-12X06X06 12" x 6" 6" BOOT-12X06X07 12" x 6" 7" BOOT-12X08X08 12" x 8" 8" BOOT-14X08X08 14” x 8” 8”

R6.0 Insulation Integrated Collar Metal Top Sealed

Return Air Boxes Item Number Box Size BOOT-RA-10X10 10" x 10" BOOT-RA-12X12 12" x 12" BOOT-RA-14X14 14" x 14" BOOT-RA-16X16 16" x 16" BOOT-RA-18X18 18" x 18" BOOT-RA-18X24 18” x 24” BOOT-RA-20X20 20" x 20" BOOT-RA-20X25 20” x 25” BOOT-RA-24X24 24" x 24"

R6.0 Insulation Return boxes are

oversized by 1/2” to accommodate filter grilles

Item Number Size DAMPER-BLADE-04 4" DAMPER-BLADE-05 5" DAMPER-BLADE-06 6" DAMPER-BLADE-07 7" DAMPER-BLADE-08 8" DAMPER-BLADE-09 9" DAMPER-BLADE-10 10" DAMPER-BLADE-12 12" DAMPER-BLADE-14 14" DAMPER-BLADE-16 16" DAMPER-BLADE-18 18" DAMPER-BLADE-20 20"

Item Number Size CONNECTOR-06 6" CONNECTOR-07 7" CONNECTOR-08 8" CONNECTOR-09 9" CONNECTOR-10 10" CONNECTOR-12 12" CONNECTOR-14 14" CONNECTOR-16 16" CONNECTOR-18 18" CONNECTOR-20 20"

Item Number Description BOOTRAIL 26" Bootrail - 26ga.

BOOTRAIL-L 26" “L” Style Bootrail - 26ga CANSTOCK-1.5 2" x 1.5" x 10' Canstock CANSTOCK-2 2" x 2" x 10' Canstock HEATSHIELD 5-1/2” x 1/2" x 8' - 30ga.

HEATSHIELD-6 6” x 3/4" x 8' - 26ga. U-CHANNEL-2-22 1" x 2" x 1" x 10' - 22ga.

Endcaps Collars Connectors Dampers Item Number Size

ENDCAP-04 4" ENDCAP-06 6" ENDCAP-08 8" ENDCAP-10 10" ENDCAP-12 12” ENDCAP-14 14"

Reducers Item Number Size REDUCER-04X03 4" x 3" Plain Tapered Reducer REDUCER-06X04 6" x 4" Plain Tapered Reducer REDUCER-06X05 6" x 5" Plain Tapered Reducer REDUCER-07X06 7" x 6" Plain Tapered Reducer REDUCER-08X06 8" x 6" Plain Tapered Reducer REDUCER-08X07 8" x 7" Plain Tapered Reducer

Item Number Size REDUCER-09X08 9" x 8" Plain Tapered Reducer REDUCER-10X08 10" x 8" Plain Tapered Reducer REDUCER-10X09 10" x 9" Plain Tapered Reducer REDUCER-12X10 12" x 10” Plain Tapered Reducer REDUCER-14X12 14" x 12” Plain Tapered Reducer REDUCER-16X14 16" x 14” Plain Tapered Reducer REDUCER-18X16 18" x 16” Plain Tapered Reducer REDUCER-20X18 20" x 18” Plain Tapered Reducer

9

Item Number Diameter Length Gauge SNAPLOCK-04X60-26 4" 60" 26ga. SNAPLOCK-05X60-26 5" 60" 26ga. SNAPLOCK-06X60-26 6" 60" 26ga. SNAPLOCK-07X60-26 7" 60" 26ga. SNAPLOCK-08X60-26 8" 60" 26ga. SNAPLOCK-09X60-26 9" 60" 26ga. SNAPLOCK-10X60-26 10" 60" 26ga. SNAPLOCK-12X60-26 12" 60" 26ga. SNAPLOCK-14X60-26 14" 60" 26ga. SNAPLOCK-16X36-26 16" 36" 26ga. SNAPLOCK-18X36-26 18" 36" 26ga. SNAPLOCK-20X36-26 20" 36" 26ga.

Metal Products Snap-Lock Pipe

Elbows (shipped straight)

Item Number Diameter ELBOW-04-ST 4" ELBOW-05-ST 5" ELBOW-06-ST 6" ELBOW-07-ST 7" ELBOW-08-ST 8" ELBOW-09-ST 9" ELBOW-10-ST 10" ELBOW-12-ST 12" ELBOW-14-ST 14" ELBOW-16-ST 16" ELBOW-18-ST 18" ELBOW-20-ST 20"

Tees Item Number Description

TEE-06X06X06 6" x 6" x 6" Straight Tee TEE-08X08X08 8" x 8" x 8" Straight Tee TEE-10X10X10 10" x 10" x 10" Straight Tee TEE-12X12X12 12" x 12" x 12" Straight Tee TEE-14X14X14 14" x 14" x 14" Straight Tee

Straight Wyes

“T-Fin” Flexible Compressed Aluminum Duct

Item Number Size TAKEOFF-04 4" TAKEOFF-05 5" TAKEOFF-06 6" TAKEOFF-07 7" TAKEOFF-08 8" TAKEOFF-09 9" TAKEOFF-10 10" TAKEOFF-12 12"

Adhesive Takeoffs

Item Number Description WYE-12X10X10 12" x 12" x 12" Reducing Wye WYE-14X12X12 14" x 12" x 12" Reducing Wye

Item # Description TFIN-04 4" x 8' Compressed Flexible Aluminum Duct TFIN-06 6" x 8' Compressed Flexible Aluminum Duct TFIN-08 8" x 8' Compressed Flexible Aluminum Duct

Item Number Description WYE-04X04X04 4" x 4" x 4" Straight Wye WYE-06X06X06 6" x 6" x 6" Straight Wye WYE-08X08X08 8" x 8" x 8" Straight Wye WYE-10X10X10 10" x 10" x 10" Straight Wye WYE-12X12X12 12" x 12" x 12" Straight Wye WYE-14X14X14 14" x 14" x 14" Straight Wye WYE-16X16X16 16" x 16" x 16" Straight Wye WYE-18X18X18 18" x 18" x 18" Straight Wye WYE-20X20X20 20" x 20" x 20" Straight Wye

Reducing Wyes

Item Number Size VENT-EXHAUST-04 Dryer / Exhaust Vent - 4" VENT-EXHAUST-06 Dryer / Exhaust Vent - 6"

Exhaust Vents (with screen and flapper)

Item Number Size VENT-INTAKE-04 Fresh Air Intake - 4" VENT-INTAKE-06 Fresh Air Intake - 6" VENT-INTAKE-08 Fresh Air Intake - 8"

Intake Vents (with screen)

Item Number Size VENT-GRVD-04 Standard Height Roof Vent - 4" VENT-GRVD-10 Standard Height Roof Vent - 10"

VENT-GRVTD-04 Tall Height Roof Vent - 4" VENT-GRVTD-10 Tall Height Roof Vent - 10"

Roof Vents (with screen and flapper)

Line Jacks Item Number Size

LINEJACK-10 10” Roof Linejack - 26ga.

10

Commercial “Lay In” Grilles Supply Diffusers - R6 Insulated Back

Item Number Type GRILLE-SCFIU2424-3 Hi-Velocity 3-Cone - All Steel GRILLE-EPRIU2424 Flat Panel - All Steel

GRILLE-UHU6A40606-W Aluminum Louvered Face - 6” x 6” Core GRILLE-UHU6A40909-W Aluminum Louvered Face - 9” x 9” Core GRILLE-UHU6A41212-W Aluminum Louvered Face - 12” x 12” Core GRILLE-UHU6A41515-W Aluminum Louvered Face - 15” x 15” Core GRILLE-UHU6A41818-W Aluminum Louvered Face - 18” x 18” Core

Many more commercial sizes and styles available – please consult your Trane Supply representative with your needs.

Cube Core Concentric Diffusers

SCFIU-24243 EPRIU2424 UHU6A41212

Return Grilles - R6 Insulated Back

Item Number Type GRILLE-PDB Perforated Supply/Return Grille GRILLE-PRF2 Perforated Return Grille w/ 1” Filter

GRILLE-RATU2424 Aluminum Louvered Return GRILLE-RAFTU2424 Aluminum Louvered Return w/ 1” Filter

PDB PRF-2 RATU/RAFTU2424

Modular Core

Linear Slots Linear Bars

11

Grilles & Diffusers Ceiling Supply Grilles

Integral Multi-Shutter Damper Supply Grilles Roll-formed aluminum construction Frame gasketing to prevent streaking

Many more sizes and styles available –

please consult your Trane Supply

representative with your needs.

Item Number Size Application Style Item Number Size Application Style GRILLE-CL1M0804 8" x 4" Ceiling 1-Way GRILLE-CL2M0808 8" x 8" Ceiling 2-Way GRILLE-CL1M0808 8" x 8" Ceiling 1-Way GRILLE-CL2M1006 10" x 6" Ceiling 2-Way GRILLE-CL1M1006 10" x 6" Ceiling 1-Way GRILLE-CL2M1008 10" x 8" Ceiling 2-Way GRILLE-CL1M1008 10" x 8" Ceiling 1-Way GRILLE-CL2M1010 10" x 10" Ceiling 2-Way GRILLE-CL1M1010 10" x 10" Ceiling 1-Way GRILLE-CL2M1206 12" x 6" Ceiling 2-Way GRILLE-CL1M1206 12" x 6" Ceiling 1-Way GRILLE-CL2M1208 12" x 8" Ceiling 2-Way GRILLE-CL1M1208 12" x 8" Ceiling 1-Way GRILLE-CL2M1212 12" x 12" Ceiling 2-Way GRILLE-CL1M1212 12" x 12" Ceiling 1-Way GRILLE-CL2M1406 14" x 6" Ceiling 2-Way GRILLE-CL1M1406 14" x 6" Ceiling 1-Way GRILLE-CL2M1408 14" x 8" Ceiling 2-Way GRILLE-CL1M1408 14" x 8" Ceiling 1-Way GRILLE-CL2M1414 14" x 14" Ceiling 2-Way GRILLE-CL1M1414 14" x 14" Ceiling 1-Way GRILLE-CL2M1616 16" x 16" Ceiling 2-Way GRILLE-CL1M1616 16" x 16" Ceiling 1-Way

Item Number Size Application Style Item Number Size Application Style GRILLE-CL3M1208 12" x 8" Ceiling 3-Way GRILLE-CL4M0808 8" x 8" Ceiling 4-Way GRILLE-CL3M1212 12" x 12" Ceiling 3-Way GRILLE-CL4M1010 10" x 10" Ceiling 4-Way GRILLE-CL3M1408 14" x 8" Ceiling 3-Way GRILLE-CL4M1212 12" x 12" Ceiling 4-Way GRILLE-CL3M1414 14" x 14" Ceiling 3-Way GRILLE-CL4M1414 14" x 14" Ceiling 4-Way GRILLE-CL3M1616 16" x 16" Ceiling 3-Way GRILLE-CL4M1616 16" x 16" Ceiling 4-Way

Frame integral damper with face operator Curved blade design for ceiling applications White powder-coated paint to prevent paint peel

White Register Screws Item Number Size Pack Qty.

5-SCR81-12W #8 x 1.5" Taper-Point White Register Screw 250 (jar) 5-SCR82W #8 x 2" Taper-Point White Register Screw 250 (tub)

12

Grilles & Diffusers Sidewall Supply Grilles

Multi-shutter damper w/ face operator Roll-formed aluminum construction Frame gasketing to prevent streaking

Frame integral damper w/ face operator Teardrop blade design for sidewall applications

Item Number Size Application Style Orientation GRILLE-VM0804 8" x 4" Side Wall 1-Way Vertical GRILLE-VM1006 10" x 6" Side Wall 1-Way Vertical GRILLE-VM1206 12" x 6" Side Wall 1-Way Vertical GRILLE-VM1208 12" x 8" Side Wall 1-Way Vertical GRILLE-VM1406 14" x 6" Side Wall 1-Way Vertical GRILLE-VM1408 14" x 8" Side Wall 1-Way Vertical

Non-Filtered & Filter-Back Return Grilles No tool needed for filter removal Durable white powder coat finish 45° fixed blade core for sightproof appearance

Item Number Size Style Notes GRILLE-RA1010 10" x 10" No Filter Back GRILLE-RA1212 12" x 12" No Filter Back GRILLE-RA1414 14" x 14" No Filter Back GRILLE-RA1616 16" x 16" No Filter Back GRILLE-RA1620 16" x 20" No Filter Back 16" H x 20" W GRILLE-RA1624 16" x 24" No Filter Back 16" H x 24" W GRILLE-RA1818 18" x 18" No Filter Back GRILLE-RA1820 18" x 20" No Filter Back 18" H x 20" W GRILLE-RA1824 18" x 24" No Filter Back 18" H x 24" W GRILLE-RA2418 24" x 18" No Filter Back 24" H x 18" W GRILLE-RA1830 18" x 30" No Filter Back 18" H x 30" W GRILLE-RA3018 30" x 18" No Filter Back 30" H x 18" W GRILLE-RA2020 20" x 20" No Filter Back GRILLE-RA2024 20" x 24" No Filter Back 20” H x 24” W GRILLE-RA2025 20" x 25" No Filter Back 20" H x 25" W GRILLE-RA2520 25" x 20" No Filter Back 25" H x 20" W GRILLE-RA2030 20" x 30" No Filter Back 20" H x 30" W GRILLE-RA3020 30" x 20" No Filter Back 30" H x 20" W GRILLE-RA2424 24" x 24" No Filter Back

Item Number Size Style Notes GRILLE-RAFFS1010 10" x 10" 1" Disposable Filter Frame GRILLE-RAFFS1212 12" x 12" 1" Disposable Filter Frame GRILLE-RAFFS1224 12" x 24" 1" Disposable Filter Frame 12” blades GRILLE-RAFFS1414 14" x 14" 1" Disposable Filter Frame GRILLE-RAFFS1616 16" x 16" 1" Disposable Filter Frame GRILLE-RAFFS1620 16" x 20" 1" Disposable Filter Frame 16” blades GRILLE-RAFFS1624 16" x 24" 1" Disposable Filter Frame 16” blades GRILLE-RAFFS1818 18" x 18" 1" Disposable Filter Frame GRILLE-RAFFS1820 18" x 20" 1" Disposable Filter Frame 18" blades GRILLE-RAFFS1824 18" x 24" 1" Disposable Filter Frame 18" blades GRILLE-RAFFS2418 24" x 18" 1" Disposable Filter Frame 24” blades GRILLE-RAFFS1830 18" x 30" 1" Disposable Filter Frame 18" blades GRILLE-RAFFS3018 30" x 18" 1" Disposable Filter Frame 30” blades GRILLE-RAFFS2020 20" x 20" 1" Disposable Filter Frame GRILLE-RAFFS2024 20" x 24" 1" Disposable Filter Frame 20” blades GRILLE-RAFFS2025 20" x 25" 1" Disposable Filter Frame 20” blades GRILLE-RAFFS2520 25" x 20" 1" Disposable Filter Frame 25” blades GRILLE-RAFFS2030 20" x 30" 1" Disposable Filter Frame 20” blades GRILLE-RAFFS3020 30" x 20" 1" Disposable Filter Frame 30” blades GRILLE-RAFFS2424 24" x 24" 1" Disposable Filter Frame

13

Air Handler Mounting Air Handler Blocks

Dimensions Item # Height Depth Width

#040 17" 22" 16" - 27" #004-999 17” 22" 20” - 32”

#031 28" 22" 14" - 25"

Trane Air Handler Stand (sized, insulated)

#040 #004-999

#031

#500 Series

#001-360 #004-375

Secondary Drain Pans

Item Number Size PAN-28X48-26G 28" x 48" PAN-28X54-26G 28" x 54" PAN-28X58-26G 28" x 58" PAN-28X60-26G 28" x 60" PAN-30X60-26G 30" x 60" PAN-30X66-26G 30" x 66"

Item Number Size Application PAN-16X34-26G 16" x 34" Honeywell DR65 Dehumidifier PAN-20X38-26G 20" x 38" Honeywell DR90/120 Dehumidifier

Item Number Size PAN-24X24-26G 24" x 24" PAN-26X26-26G 26" x 26" PAN-30X30-26G 30” x 30"

For Vertical Applications

Item Number Size PAN-26X40-26G 26" x 40" PAN-26X48-26G 26" x 48" PAN-26X52-26G 26" x 52" PAN-26X56-26G 26" x 56" PAN-26X62-26G 26" x 62" PAN-26X68-26G 26" x 68"

For Horizontal Applications

Lightweight Styrofoam block (concrete gray) provides air handler support in attic installations. 8” x 8” x 4” block. Item # Case Qty.

7-60 144

Item # Contents Qty. HANGER KIT 3/8" 32” x 14 Gauge Slotted Angles 2

3/8” x 6ft Threaded Rods 4 1/4” x 3” Eye Bolts 4 1/4” x 2” Eye Lag Bolts 4 1/4” Hex Nuts 4 3/8” Hex Nuts 8 5/16” Flat Washers 12 3/8” Fender Washers 4

Specialty Applications

Air Handler Hanging Kit

Air Handler Stand (adjustable, non-insulated)

Fits Item # H D W TEM4 TEM6 TAM4 GAM5 TAM7/8 GAF2

#500-315 20" 22" 18" - - 18-36 18-24 24 18-36 #500-317 20" 22" 18.5" 18-30 24-30 - - - - #500-324 20" 22" 21.5" - - 42 30-36 30 - #500-327 20" 22" 23.5" 36-60 36-42* 48-60 42-60 36-60 - #500-332 20" 22" 26.5" - 48-60* - - - -

* "D" Model 48 & 60 TEM6 units use the 26.5" wide stand. "C" Model 48 & 60 TEM6 units use the 23.5" wide stand.

Accessory Description #001-360 4" corner legs for insulated AHU stands - 4pk. #004-375 4" Tall mini-stand for insulated AHU stands

“Coffin Box” Premium Stand

Contractor cuts proper size openings for the return and supply. Lined with R-6 Anti-Microbial Fiberglass.

Item # Height Depth Width #003-505 19" 21" 46" #003-508 19" 24" 46" #003-512 19" 28” 46"

Accessory Description #004-009 4" Tall mini coffin box stand

14

Item # Size Item # Size H1840-4 18" x 40" x 4" H3652-4 36" x 52" x 4" H3030-4 30" x 30" x 4" H3672-4 36" x 72" x 4" Placing 2 of these units side-by-side can create a large

base for a commercial unit (either 72" x 72" or 76" x 65") H3636-4 36" x 36" x 4" H3865-4 38" x 65" x 4" H3642-4 36" x 42" x 4" H4040-4 40" x 40" x 4"

H3648-4 36" x 48" x 4" H4558-4 45" x 58" x 4"

Condenser Mounting Hurricane Pads

Roof Stands

Roof Stand Leg # Description ROOFSTAND-LEG18 18" Tall Adjustable Roof Stand Leg ROOFSTAND-LEG21 21" Tall Adjustable Roof Stand Leg ROOFSTAND-LEG24 24" Tall Adjustable Roof Stand Leg

Roof Stand Rail # Description ROOFSTAND-RAIL3 3' Roof Stand Beam ROOFSTAND-RAIL6 6' Roof Stand Beam ROOFSTAND-RAIL9 9' Roof Stand Beam

ROOFSTAND-RAIL12 12' Roof Stand Beam ROOFSTAND-RAIL15 15' Roof Stand Beam ROOFSTAND-RAIL18 18' Roof Stand Beam

Custom-Sized Roof Stands are Available!

Wall-Mount Brackets

Unit / Size Table AC Stand Length 3 Ft. 6 Ft. 9 Ft. 12 Ft. 15 Ft. 18 Ft.

Roof Type All All All All All All Max # Units 1 2 3 4 5 6

Max Surface Area Per Unit 9 Sq. Ft. 9 Sq. Ft. 9 Sq. Ft. 9 Sq. Ft. 9 Sq. Ft. 9 Sq. Ft. Total Surface Area 9 Sq. Ft. 18 Sq. Ft. 27 Sq. Ft. 36 Sq. Ft. 45 Sq. Ft. 54 Sq. Ft.

Kit comes neatly packaged in a box and includes condenser tie downs with screws and engineering documents

Braces are T5 Aluminum with MIG welded joints & seams

Withstands wind speeds up to 186 mph per 2014 FBC & ASCE 7-10

Item # Description

#007-840 18" H x 24" D Aluminum Mini-Split Wall Bracket - 400lb. Load

#007-850 36" H x 48" D Aluminum Wall Bracket - 400lb. Load

15

Trane “Extreme Condition” Condenser Mounting Kit

Trane Extreme Conditions Mounting Kits meet the requirements of the Florida Building Code (2007) for wind resistance and anchoring requirements at a maximum wind speed of 150mph at a 3-second gust. Each kit will mount 5-10 units depending on condenser height.

Item # Trane OE Item # Qty.

KIT15190 BAYECMT023 5-10 Units

Tie Down Kits

Roof Curb Screws (with bonded washer)

Item # Description Qty. BMTD04 4" x 1” Condenser Tie Down 4pk. BMTD06 6" x 1” Condenser Tie Down 4pk.

BMTD06S 6" x 1” Tie Down w/ Screws 4pk. BMTD062L 6" x 2” Condenser Tie Down 4pk.

FBTD “Fatboy” 4” x 1.5” Tie Down 4pk.

Item # Size Case Qty. Type

MP-2E 2" x 2" x 7/8" 48 EVA Composite MP-2C 2" x 2" x 7/8" Cork/Rubber 48 MP-4E 4" x 4" x 7/8" 48 EVA Composite

Isolators

Type Model No. TWE

061D/E TWE

090D/E TWE

120D/E TWE

150E-180E TWE 240E

TTA/TWA 073D-090D

TTA/TWA 120D

TTA 120E/F

TTA/TWA 150-180E/F

TTA/TWA 240E/F

Suspended Isolator

(Rubber)

BAYISLT012A X BAYISLT013A X BAYISLT014A X BAYISLT015A X BAYISLT016A X

Suspended Isolator (Spring)

BAYISLT028A X BAYISLT029A X X BAYISLT030A X BAYISLT031A X

Floor Isolator

(Rubber)

BAYISLT004A X X X BAYISLT005A X X X BAYISLT009A X X BAYISLT010A X X

Floor Isolator (Spring)

BAYISLT019A X X X BAYISLT021A X BAYISLT023A X X BAYISLT024A X X BAYISLT025A X BAYISLT032A X

Floor Isolator (Steel) Floor Isolator (Rubber) Suspended Isolator (Rubber) Suspended Isolator (Steel)

Vibration isolators are used to reduce the transmission of

noise, shock, and vibration produced by mechanical,

equipment within a building structure.

Anti-Vibration Pads

Concrete Anchors Item # Diameter Box Qty. Head Size Length

ANCHOR-1.25 1/4” 100 5/16” Hex Head 1-1/4” ANCHOR-1.75 1/4” 5/16” Hex Head 100 1-3/4” ANCHOR-2.25 1/4” 100 5/16” Hex Head 2-1/4”

For weathertight sealing of roof and wall applications. Hex head with bonded washer.

Item # Diameter Box Qty. Head Size Length

ANCHOR-3 1/4” 25 5/16” Hex Head 3” ANCHOR-6 1/4” 3/8” Hex Head 25 6” ANCHOR-8 1/4” 25 3/8” Hex Head 8”

16

Webbed & Panduit Strap Duct Hanging Products Metal Strap

Item # Type Gauge Length 710-A1710 Strapping Hanger Iron 28 10'

710-001 1" Duct Strap 26 100' 710-004 1-1/2" Duct Strap 26 100'

DUCTSTRAP-2 2” Duct Strap 26 100' U-CHANNEL-2-22 1" x 2" x 1” 22 10’

Item # Type Length Qty. 7-P36 Cable Tie for up to 10" Duct 36" 50/bag 7-P48 Cable Tie for up to 14" Duct 48" 50/bag

710-100 1-3/4" Webbed Strap 100 Yard Roll

Item # Description UL Listing IS-2000 Ideal® 2.5" Foil Tape UL 181A-P / UL 181B-FX 1581A Venture® 2.5" Foil Tape UL 181A-P

810 Fasson® 2.5" Foil Tape UL 181A-P 802 Fasson® 2.5" Foil Tape UL 723 821 Fasson® 3.0" Foil Scrim Tape UL 723

Tapes & Adhesives Metal Tapes

Insulation Tapes Duct Tapes Item # Description Dimensions 6-330 Cork Insulation Tape 1/8" x 2" x 30' Roll

6-9718 Foam Insulation Tape 1/8" x 2" x 30' Roll GASKET-1/2 Register Box Gasketing 1/2” x100’ Roll

Item # Description UL Listing 950 Black Duct Tape Economy Duct Tape

957B 14mil Black Duct Tape UL 181B-FX

Caulking Products Item # Description Qty. 1000S Fasson Spray Adhesive 17 fl. oz. Can 01714 Foam Sealant 12 oz. Can

Spray Adhesives Item # Description Qty.

7-4000 Clear Silicone Caulk 10.3 fl. oz. Tube 7-4100 White Silicone Caulk 10.3 fl. oz. Tube

FIRESEAL-814 Firestop Caulk—Red 10.3 fl. oz. Tube 6-202-1 DiversiGum Sealing Compound 1 lb. Slug AG-25 DiversiGum Caulking Cord 3/8" x 25' Cord 7-200 Standard Duty Caulk Gun

Item Number AFG1403

Foil Grip Mastic Tape Foil Tape & Rolled Mastic in One! Foil-Grip 1403-181BFX is a UL 181B-FX pressure sensitive, 40-year cycle, duct joint and general purpose rolled sealant. Foil-Grip 1403-181BFX provides an instant water resistant grip to most surfaces including sheet metal, duct board, flex duct, PVC coated duct, and duct wrap vapor barriers.

17

RCD Corporation® Mastics Mastics

Disconnects Pre-Made Whips

#6 Mastic® Low to High Velocity Air Duct Sealant is fiber reinforced and preferred by professionals for sealing air ducts, thermal insulation, house wrap and crawl space vapor retarders in home weatherization projects, remodels, retrofits and new construction. #6 Mastic® is easily applied by brush, trowel, palm, spray or extrusion. UL Listed. Cream White in color.

#8 Mastic® Low to High Velocity Sheet Metal Air Duct Sealant is the best choice for permanently sealing high velocity sheet metal air ducts in schools, apartments, hospitals, offices, large retail spaces, dormitories, government and military installations. UL Listed. Gray in color.

#9 Mastic® Low to High Velocity Air Duct Sealant is preferred by HVAC contractors installing fiberglass duct board and flexible duct systems. When applied around the top perimeter of a crawl space #9 Mastic® creates an easily monitored zone for detecting termites crossing the barrier to the wooden structure. UL Listed. White in color.

#10 Mastic® Low to High Velocity Air Duct Sealant is fiber reinforced and seals the fabricated joints and seams of thermal insulation and air ducts. Easily applied by brush, trowel, palm, spray or extrusion (ask for tech bulletin on recommended spray/extrusion equipment). UL listed. Tan in color.

#15 Weather Barrier Coating® is a bright white, elastomeric coating for protecting air ducts and thermal insulation exposed to the weather. It prevents degradation of closed cell foam insulation on line sets, provides years of service as a lagging adhesive and reflects solar radiation as a roof coating. Applied by brush, roller or spray equipment (ask for tech bulletin on recommended spray equipment). UV resistant. Bright White in color.

Item # Description Size RCD-6-1 #6 Mastic® 1 Gallon RCD-6-2 #6 Mastic® 2 Gallon RCD-8-1 #8 Mastic® 1 Gallon RCD-8-2 #8 Mastic® 2 Gallon RCD-9-1 #9 Mastic® 1 Gallon RCD-9-2 #9 Mastic® 2 Gallon

RCD-15-1 #15 Weather Barrier® 1 Gallon RCD-10-1 #10 Economy Mastic® 1 Gallon RCD-10-2 #10 Economy Mastic® 2 Gallon

An all purpose duct sealant for use on all types of metal duct, fiberglass duct board, duct fabric and flex duct. CCWI-181 incorporates a built-in polyester reinforcement for exceptional strength, with UV inhibitors for outdoor use. UL 181A-M / UL 181B-M listed.

Item # Description Size 303180 Glasscoat® Joint Scrim 3" X 180' Roll

MASTIC BRUSH 3" Chip Brush 3" 307214 Fin & Plenum Brush 2" x 18"

Accessories Mastics

Item # Description WHIP-1/2 1/2” x 6’ #10 THHN Wire – Non-Metallic Connectors WHIP-3/4 3/4” x 6’ #8 THHN Wire – Non-Metallic Connectors

WHIP-3/4HD 3/4” x 6’ #6 THHN Wire – Non-Metallic Connectors

Electrical

Liquid-Tite Fittings Item # Description

750-12100 1/2” x 100’ Liquid Tite Conduit – Non-Metallic, 100’ roll 750-34100 3/4” x 100’ Liquid Tite Conduit – Non-Metallic, 100’ roll

Liquid-Tite Conduit

Liquid-tight flexible conduit system. A labor saving convenience kit for unit hookup.

Item # Description Box Qty.

750-NMLT50 1/2” Non-Metallic Straight Connector 25 750-NMLT9050 1/2” Non-Metallic 90 Degree Elbow 10

750-NMLT75 3/4” Non-Metallic Straight Connector 10 750-NMLT9075 3/4” Non-Metallic 90 Degree Elbow 10

Item # Description DDS-60U 60A Non-Fusible Disconnect Switch

QO-200TR Square D 60A Circuit-Breaker Disconnect

Item Number Size CCWI-181 1 Gallon

CCWI-181-2 2 Gallon

18

For systems requiring 14AWG interconnect wire

Item # Description COP-1/4 1/4" x 50' Copper Roll

COP-5/16 5/16" x 50' Copper Roll COP-3/8 3/8" x 50' Copper Roll COP-1/2 1/2" x 50' Copper Roll COP-5/8 5/8" x 50' Copper Roll COP-3/4 3/4" x 50' Copper Roll COP-7/8 7/8" x 50' Copper Roll

COP-1-1/8 1-1/8" x 50' Copper Roll

Item # Description COP-3/8-100FT 3/8" x 100' Copper Roll COP-1/2-100FT 1/2" x 100' Copper Roll COP-5/8-100FT 5/8" x 100' Copper Roll COP-3/4-100FT 3/4" x 100' Copper Roll COP-7/8-100FT 7/8" x 100' Copper Roll

COP-1-1/8-100FT 1-1/8" x 100' Copper Roll

Item # Description Feet per

Spool THM-18/2-S 18/2 Spooled Wire 500 ft. THM-18/3-S 18/3 Spooled Wire 500 ft. THM-18/4-S 18/4 Spooled Wire 250 ft. THM-18/5-S 18/5 Spooled Wire 250 ft. THM-18/6-S 18/6 Spooled Wire 250 ft. THM-18/7-S 18/7 Spooled Wire 250 ft. THM-18/8-S 18/8 Spooled Wire 250 ft. THM-18/9-S 18/9 Spooled Wire 250 ft.

THM-18/10-S 18/10 Spooled Wire 250 ft. THM-18/12-S 18/12 Spooled Wire 250 ft.

18AWG Thermostat Wire

Soft Copper Rolls - 50ft. Soft Copper Rolls -100ft.

ACR Copper - 20ft. Sticks Item # Description Item # Description ACR-3/8 3/8" ACR Copper Stick - 20ft. ACR-7/8 7/8" ACR Copper Stick - 20ft. ACR-1/2 1/2" ACR Copper Stick - 20ft. ACR-1-1/8 1-1/8" ACR Copper Stick - 20ft. ACR-5/8 5/8" ACR Copper Stick - 20ft. ACR-1-3/8 1-3/8" ACR Copper Stick - 20ft. ACR-3/4 3/4" ACR Copper Stick - 20ft. ACR-1-5/8 1-5/8" ACR Copper Stick - 20ft.

ACR-2-1/8 2-1/8" ACR Copper Stick - 20ft.

25' Item # 50' Item # Description ILS-2506 ILS-5006 1/4" x 3/8" - 14-3 Power / 16-2 Shielded Com ILS-2507 ILS-5007 1/4" x 1/2" - 14-3 Power / 16-2 Shielded Com

ILS-2509 ILS-5009 1/4" x 5/8" - 14-3 Power / 16-2 Shielded Com ILS-2510 ILS-5010 3/8" x 5/8" - 14-3 Power / 16-2 Shielded Com

Wire & Linesets Ductless Linesets For systems requiring 16/2 shielded com wire

25' Item # 50' Item # Description SLS2506 SLS5006 1/4" x 3/8" - 14/7 Interconnect Wire SLS2507 SLS5007 1/4" x 1/2" - 14/7 Interconnect Wire SLS2508 SLS5008 3/8" x 5/8" - 14/7 Interconnect Wire SLS2509 SLS5036 1/4" x 5/8" - 14/7 Interconnect Wire

Item # Description Feet per I33-100 16/2 Shielded Plenum Control Wire 100 ft.

I33-250 16/2 Shielded Plenum Control Wire 250 ft. THM-14/4-PL 14/4 Shielded Plenum Power & Control Wire 100 ft.

M33-100 14/7 Power & Control Wire 100 ft.

Ductless Control Wire

RectorSeal NoKink™ Flexible Refrigerant Lines RectorSeal® NoKink™ is a flexible connection between the refrigerant line and a wall mounted minisplit evaporator. It allows easier kink free installation of the minisplit evaporator to the wall bracket. Install by silver solder or flaring.

Item # Description 66731 1/4" Flexible Refrigerant Line Connector - 36" long 66733 3/8" Flexible Refrigerant Line Connector - 36" long 66737 1/2" Flexible Refrigerant Line Connector - 36" long 66735 5/8" Flexible Refrigerant Line Connector - 36" long

19

Rolled Stop Couplings - C x C Reducing Couplings - C x C

Fitting # Size Pack Qty. W01003 1/4" 25 W10142 5/16" 25 W01009 3/8" 25 W01017 1/2" 25 W01022 5/8" 25 W01028 3/4" 25 W01034 7/8" 25 W01047 1-1/8" 10 W01055 1-3/8" 5 W01063 1-5/8" 5 W01072 2-1/8" 1

Fitting # Description Pack Qty.

W01010 3/8" x 5/16" 25 W01019 1/2" x 3/8" 25 W01023 5/8" x 1/2" 25 W01029 3/4" x 5/8" 25 W01035 7/8" x 3/4" 25 W01049 1-1/8" x 7/8" 10 W01056 1-3/8” x 1-1/8" 1 W01064 1-5/8” x 1-3/8" 1 W01073 2-1/8” x 1-5/8" 1

45⁰ Elbow - C x C Tees - C x C x C

Fitting # Fitting

Size Coupling

Size Pack Qty.

W01306 3/8" 1/4" 25 W01312 1/2" 3/8" 25 W01315 5/8" 1/2" 25 W01320 3/4" 5/8" 25 W01325 7/8" 3/4" 25 W01337 1-1/8" 7/8" 10 W01343 1-3/8" 1-1/8" 1 W01350 1-5/8" 1-3/8" 1 W01358 2-1/8" 1-5/8" 1

Fitting # Size Pack Qty.

W04000 3/8" 25 W04001 1/2” 25 W04006 5/8" 25 W04017 3/4" 10 W04031 7/8" 10 W04048 1-1/8" 5 W04068 1-3/8" 5 W04084 1-5/8" 5 W40102 2-1/8" 1

Reducing Fittings - FTG x C No-Stop Couplings - C x C

Fittings

90⁰ L. R. Elbow - C x C 90⁰ L.R. Street Elbow - FTG x C

Fitting # Size Pack Qty. W02715 1/4" 25 W02710 5/16" 25 W02716 3/8" 25 W02717 1/2" 25 W02722 5/8" 25 W02728 3/4" 25 W02734 7/8" 10 W02747 1-1/8" 5 W02055 1-3/8" 5 W02063 1-5/8" 5 W02072 2-1/8" 1

Fitting # Size Pack Qty.

W02809 3/8" 25 W02817 1/2" 25 W02822 5/8" 25 W02828 3/4" 25 W02834 7/8" 10 W02847 1-1/8" 5 W02350 1-3/8" 5 W02355 1-5/8" 5 W02359 2-1/8" 1

Fitting # Size Pack Qty.

W03012 3/8" 25 W03021 1/2" 25 W03026 5/8" 25 W03030 3/4" 25 W03034 7/8" 25 W03044 1-1/8" 10 W03050 1-3/8" 10 W03055 1-5/8" 5 W03059 2-1/8" 5

Self-Flare Fittings Triple metallic seal No torque wrench required Working temperature: -49°F to 302°F Maximum operating pressure: 652 psi Suitable for all refrigerants HCFC, HFC, HC Compatible with traditional 45° flare fittings

Item # Description ES14 1/4" Self Flare Fitting - 2 Pack ES38 3/8" Self Flare Fitting - 2 Pack ES12 1/2" Self Flare Fitting - 2 Pack ES58 5/8" Self Flare Fitting - 2 Pack

Item # Description DNS4-4 1/4” Short Forged Flare Nut - 10 Pack DNS4-6 3/8” Short Forged Flare Nut - 10 Pack DNS4-8 1/2” Short Forged Flare Nut - 10 Pack

DNS4-10 5/8” Short Forged Flare Nut - 10 Pack

Flare Nuts

Insert the tube, previously cut and

deburred, into the nut and then insert the sleeve

Hand tighten the nut to the joint

Mark the starting point and make a complete

turn and a half with the aid of a common wrench

Fitting # Size Pack Qty. W01900 1/4" 25 W01901 3/8" 25 W01902 1/2" 25 W01903 5/8" 25 W01904 3/4" 25 W01905 7/8" 25 W01906 1-1/8" 10 W01907 1-3/8" 5 W01908 1-5/8" 5 W01909 2-1/8" 1

20

Item Number Dimensions Length Cap LINECOVER-4X5X08 4" x 5" x 4" 8' None LINECOVER-4X5X10 4" x 5" x 4" 10' None

Tubing Insulation

PROTECTED UNTREATED

1/2” Wall Thickness - 6’ Sticks 3/4” Wall Thickness - 6’ Sticks Item # Mfg. #

Tube OD

Wall Size

Case Qty.

ARM-1/4X1/2 ACT01412 1/4" 1/2" 95 ARM-3/8X1/2 ACT03812 3/8" 1/2" 75 ARM-1/2X1/2 ACT01212 1/2" 1/2" 66 ARM-5/8X1/2 ACT05812 5/8" 1/2" 50 ARM-3/4X1/2 ACT03412 3/4" 1/2" 40 ARM-7/8X1/2 ACT07812 7/8" 1/2" 35

ARM-1-1/8X1/2 ACT11812 1-1/8" 1/2" 25 ARM-1-3/8X1/2 ACT13812 1-3/8" 1/2" 20

Item # Mfg. # Tube OD

Wall Size

Case Qty.

ARM-3/8X3/4 ACT03834 3/8” 3/4” 40 ARM-1/2X3/4 ACT01234 1/2" 3/4" 35 ARM-5/8X3/4 ACT05834 5/8" 3/4" 24 ARM-3/4X3/4 ACT03434 3/4" 3/4" 23 ARM-7/8X3/4 ACT07834 7/8" 3/4" 20

ARM-1-1/8X3/4 ACT11834 1-1/8" 3/4" 15 ARM-1-3/8X3/4 ACT13834 1-3/8" 3/4" 12 ARM-1-5/8X3/4 ACT15834 1-5/8" 3/4" 10 ARM-2-1/8X3/4 ACT21834 2-1/8" 3/4" 9

3/16” Wall Size - 6’ Sticks For Condensate Line Applications

Item # Mfg. # Tube OD

Wall Size

Case Qty.

ARM-1-1/8X3/16 OET11836N2 1-1/8" 3/16" 44

Sheet Insulation

Item # Mfg. # Sheet Size Thickness

Case Qty.

ARM SHEET-3X4X3/4 APS34043 3' x 4' 3/4" 8 ARM SHEET-3X4X1 APS10043 3' x 4' 1" 6

Insulation Glue

#15 Weather Barrier Coating® is a bright white, elastomeric coating for protecting air ducts and thermal insulation exposed to the weather. It prevents degradation of closed cell foam insulation on line sets, provides years of service as a lagging adhesive and reflects solar radiation as a roof coating. Applied by brush, roller or spray equipment. UV resistant. Bright White.

Item # Mfg. # Size

ARM GLUE-1/2 PINT Armaflex® 520 1/2 Pint

Insulation Paint - Item # RCD-15-1

Capped

Metal Linecovers Uncapped

Item Number Dimensions Length Cap LINECOVER-4X5X08C 4" x 5" x 4" 8' Angled LINECOVER-4X5X10C 4" x 5" x 4" 10' Angled

21

Image Item # Description Image Item # Description Image Item # Description

LD122I 8' Ducting LFJ122I Flexible Adaptor

LCO122I 90° Outside Vertical Elbow

LJ122I Coupler LWF122I Flex. Wall Flange LCFI122I 45° Inside

Vertical Elbow

LW122I Wall Inlet LK122I 90° Flat Elbow LCFO122I 45° Outside Vertical Elbow

LEN122I End Fitting LKF122I 45° Flat Elbow LKS122I 90° Sweep Elbow

LP122I Soffit Inlet LCI122I 90° Inside Vertical Elbow LF122I Flexible Elbow

LT122I Tee

Fortress Lineset Ducting

Item # Description LDK122I Complete 12’ Fortress Lineset Kit

Application. Fortress is perfect for minisplits, high velocity and conventional split air conditioning systems. Strong. Fortress ducting is extruded with our special formula rigid polyvinyl chloride, which is UV and weather resistant The result is a long lasting quality product that will remain attractive and provide protection for many years. Protective. Fortress protects lineset, wiring and drain hose from weather, vandalism and pest damage. Easy to install. Fortress installs quickly, and can be easily accessed for repairs or replacement of the lineset. Stylish. Fortress eliminates unsightly lineset used in a typical installation. Ducting is available in two lineset sizes and four neutral colors - white, ivory, brown and gray to compliment any residential or commercial building. Paintable. Brush, spray or roller to match or compliment custom colors. Follow paint manufacturers recommendations for vinyl products.

Prepackaged 12’ Duct Kit

Complete kit! Includes 12' of duct and essential fittings. Everything to hide and protect the lineset for a typical A/C installation in one box. Ivory Color - 4-1/2” fittings.

Individual Components Design any custom lineset with these individual components

LD-122 w/Single 1-1/8” Lineset BTU - 60,000 Suction Line - 1-1/8” OD (Insulation) - 1” Liquid Line - 1/2”OD Drain Line- 3/4”PVC

LD-122 w/Dual 3/4” Lineset BTU - 42,000 Suction Lines - 3/4”OD (Insulation ) - 1/2” Liquid Lines - 3/8”OD (Insulation ) - 1/2” Drain Hose - 7/8” OD

LDK Kit includes: (3) LD - 4' Duct lengths (2) LJ - Couplers (1) LW - Wall Inlet (1) LEN - End Fitting (1) LK - 90º Flat Ell

Ivory (Local Stock)

White (Special Order)

Gray (Special Order)

Brown (Special Order)

22

PVC Pipe & Fittings

PVC409 PVC429 PVC407 PVC406 PVC417 PVC410 PVC436

PVC437

PVC435

PVC447 PVC450 PVC448 PVC449 RUNTRAP PTRAP

PVC401

PVC457

3/4" Item # 1" Item # Description 3/4” Item # 1” Item # Description PVC401-007 PVC401-010 Tee - SLIP x SLIP x SLIP PVC437-101 - 3/4"x 1/2" Bushing PVC406-007 PVC406-010 Elbow - SLIP x SLIP - PVC437-131 1" x 3/4" Bushing PVC407-007 PVC407-010 Elbow - SLIP x FIPT PVC447-007 PVC447-010 SLIP Cap PVC409-007 PVC409-007 Street Elbow - SPG x SLP PVC448-007 - Female (FIPT) Cap PVC410-007 - Street Elbow - MPT x SLP PVC449-007 - SLIP Plug PVC417-007 PVC417-010 45⁰ Elbow - SLIP x SLIP PVC450-007 - Male (MIPT) Plug PVC429-007 PVC429-010 Coupling - SLIP x SLIP PVC457-007 - 3/4” Threaded Union - SLIP x SLIP PVC435-007 PVC435-010 Female Adapter - SLIP x FPT RUNTRAP RUNTRAP-1 Running Trap PVC436-007 PVC436-010 Male Adapter - MPT x SLP PTRAP PTRAP-1 "P" Trap

PVC Pipe PVC Pipe # Description

PVC 3/4" Schedule 40 PVC - 10ft. Length

PVC-1 1" Schedule 40 PVC - 20ft. Length—Bell End

PVC Glues & Cleaners Item # Description

PURPLE PRIMER 8oz. Purple PVC Primer PVCCLEANER-4 4oz. Clear PVC Cleaner PVCCLEANER-8 8oz. Clear PVC Cleaner

PVCGLUE-4 4oz. Regular Clear PVC Cement PVCGLUE-8 8oz. Regular Clear PVC Cement

PVCGLUE-8HD 8oz. Heavy-Duty Clear PVC Cement RAIN-R-SHINE 8oz. Blue PVC Cement

The Pipe Prop is an adjustable pipe support system that elevates and secures industrial piping on commercial roofs. Height adjustable and easily sited.

Pipe Prop® Stands

Miami-Dade Kits: Include adhesive and PVC

USPP APS-2 APS-1 PVC pipe not included in

above kits

Item # Description APS-1 Pipe Prop - 1.5" Saddle

APS-2 Pipe Prop - 2.5" Saddle

USPP Pipe Prop - 2.5" Unistrut Saddle

APS-MDA-1 APS-1 Kit with Miami Dade PVC and Adhesive

APS-MDA-2 APS-2 Kit with Miami Dade PVC and Adhesive

USPP-MDA USPP Kit with Miami Dade PVC and Adhesive

23

Condensate Management Overflow Switches

Item # Description SS-1 Primary/Secondary In-Line Switch SS-2 Primary Pan Auxiliary Outlet Switch SS-3 Primary/Secondary Clip-Mount Switch

SS-500EP Commercial Rooftop Switch - Plenum Rated WS-1 Wet Switch - Solid State Secondary Switch

AG-1100+ Secondary Pan Clip-Mount Switch AG-1250E Multipurpose Sensor for Secondary Pans AG-2550E In-Line Switch w/ Secondary Sensor AG-3125E Primary Pan Sensor AG-3150E 2-n-1 Primary & Secondary Pan Sensors AG-3180E Plenum-Rated 2-n-1 for Commercial Rooftops

ACS-2 Little Giant Secondary Pan Switch ACS-4 Little Giant In-Line Safety Switch

SS-1 SS-2 SS-3 SS-500EP

SS-610E

AG-3150E

AG-1100+

AG-3180E

AG-2550E

Condensate Pumps Item # Description 554435 115v Condensate Pump w/ Tubing 554461 230v Condensate Pump w/ Tubing

7-38 3/8" Clear Tubing - 100ft. 701-043 3/4" MIPT x 3/8" Barb Adapter

Item # Description 553505 EC-1 Pump - 115v/208-230v 553515 EC-1 Pump with Line Cover Kit

Little Giant® Pumps

NXTGen Series 554435 / 554461

Ductless Accessories

AG-1250E AG-3125E

WS-1

ACS-2 ACS-4

Item # Description 554550 NXTGen 115v Pump with Tubing 554551 NXTGen 230v Pump with Tubing 599138 NXTGen Anti-Sweat Sleeve

599138

7-38 701-043

Ductless Condensate Blue Diamond® Pumps

Item # Description X85-003 MicroBlue - 115v/208-230v X87-721 MaxiBlue—208-230v

7-14 1/4” Clear Tubing—100’

Blue Diamond® pumps can be mounted in any orientation. The MaxiBlue’s patented rotary diaphragm technology allows the condensate to be drawn into the pump by vacuum and mechanically driven within a reinforced elastomer diaphragm to the outlet under pressure. This system even tolerates suspended solids and light slurries whilst happily running dry.

Item # Description SS-610E Minisplit Safety Switch DH-16S 5/8” Drain Line - 20’ DSH-14 5/8” Insulated Drain Line - 65’ EZT-180 Waterless In-Line Trap HC6202 1/4” to 5/8” Hose Clamps - 6pk. HC5410 9/16” to 1-1/8” Hose Clamps - 6pk. HC5420 13/16” to 1-3/4” Hose Clamps - 6pk.

DH-16S/DSH-14

EZT-180

Drain Line Fitting

Flexible End Color

Flexible End Size (mm)

Stepped End Size (mm)

230-DLF16 Yellow 16 14-16-18-20

230-DLF18 Red 18 14-16-18-20

230-DLF20 Blue 20 14-16-18-20

230-DLF25 Green 25 14-16-18-20

230-DLF32 Gray 32 14-16-18-20

Mini Split AHUs (either ceiling or wall cassettes) typically have a unique (metric) drain line fitting. These adapters convert this metric fitting to standard drain line tubing sizes.

HC Series 230-DFL18

YOUR COMPLETE SOURCEResidental & Light Commerical Equipment

Temporary Cooling & Power RentalsOEM Replacement Components

Installation & Service Supplies

16520 Scheer Blvd, Hudson, FL 34667(727) 245-1320 Fax (727) 245-1321

Hudson Sarasota

Clearwater Naples

Ft. Myers

4720 E. Adamo Drive, Tampa, FL 33605(813) 877-8253 Fax (813) 876-4778

1157 U.S. Highway 19 N, Clearwater, FL 33764(727) 572-8255 Fax (727) 573-1604

2224 72nd Terrace East, Sarasota, FL 34243(941) 360-0010 Fax (941)358-0032

6461 Topaz Court, Ft. Myers, FL 33966(239) 275-9577 Fax (239) 278-5502

544 Commercial Blvd, Naples, FL 34104(239) 384-5400 Fax (239) 384-5401

Tampa