HUAWEI BTS312 Dynamic Configuration (BTS)

8/11/2019 HUAWEI BTS312 Dynamic Configuration (BTS)

1/95

M900/M1800 Base Station ControllerData Configuration Manual - Dynamic Configuration Contents

Issue 05 (2008-11-15)Huawei Proprietary and Confidential

Copyright Huawei Technologies Co., Ltd.i

Contents

3 BTS Data Configuration ...........................................................................................................3-1 3.1 Adding a Site.................................................................................................................................................3-3

3.2 Deleting a Site.............................................................................................................................................3-22

3.3 Adding TRX................................................................................................................................................3-27

3.4 Deleting TRX........................................................ ........................................................................... ...........3-32

3.5 Adding or Deleting Board ............................................................. .............................................................. 3-38

3.6 Modifying Board Type ............................................................ .................................................................... 3-42

3.7 Configuring Site Tower-top Amplifier ................................................................... ..................................... 3-48

3.8 Modifying Site Data....................................................................................................................................3-52

3.9 Modifying Site's Output Property ............................................................................ ................................... 3-57

3.10 Starting up Traffic Stat. Task Re-register ..................................................................... .............................3-59

3.11 Renaming Site or Cell ................................................................... ............................................................ 3-60

3.12 Modifying Ring Topology Mark ....................................................................... ........................................ 3-65

3.13 Adding Slave Chain to Site ............................................................................ ........................................... 3-68

3.14 Deleting Slave Chain of Site ........................................................................ ............................................. 3-71

3.15 Configuring Site Idle Timeslot..................................................................................................................3-74

3.16 Batch Process Site Property ................................................................... ................................................... 3-78

3.17 Modifying Site Board Parameters .............................................................. ............................................... 3-82

3.18 Adding or Deleting a Break Point ........................................................................... .................................. 3-84


2/95


3/95

FiguresM900/M1800 Base Station Controller

Data Configuration Manual - Dynamic Configuration

ivHuawei Proprietary and Confidential

Copyright Huawei Technologies Co., Ltd.Issue 05 (2008-11-15)

Figure 3-27 Delete site (site BIE trunk mode)..................................................................................................3-25

Figure 3-28 Delete site (site TRX property).....................................................................................................3-26

Figure 3-29 Command list for dynamic setting................................................................................................3-26

Figure 3-30 Select site......................................................................................................................................3-28

Figure 3-31 Add TRX.......................................................................................................................................3-28

Figure 3-32 Configure cell ............................................................ ................................................................... 3-29

Figure 3-33 Assign TRX to cell........................................................................................................................3-30

Figure 3-34 Timeslot manual adjustment .................................................................. ....................................... 3-31

Figure 3-35 Select cell......................................................................................................................................3-34

Figure 3-36 Select TRX....................................................................................................................................3-34

Figure 3-37 Prompt when delete the TRX containing main BCCH ................................................................. 3-35

Figure 3-38 Indicating the user to modify the reserved channel number ......................................................... 3-35

Figure 3-39 Modify the reserved channel number ................................................................. ..........................3-36

Figure 3-40 Command list for dynamic configuration ....................................................................... ..............3-36


Figure 3-42 Add/delete board...........................................................................................................................3-39

Figure 3-43 Deleting boards for the site not supporting detach........................................................................3-39

Figure 3-44 Deleting boards for the site supporting detach..............................................................................3-40

Figure 3-45 Prompt box ....................................................... ........................................................... .................3-40


Figure 3-47 Select Site (Modify Site Board Type) ................................................................... ........................3-42

Figure 3-48 Modify Board Type (Modify Site Board Type).............................................................................3-43

Figure 3-49 Site Devices Property .................................................................. ................................................ 3-43

Figure 3-50 Set PBU Board Property...............................................................................................................3-44

Figure 3-51 Set CDU Board property...............................................................................................................3-44

Figure 3-52 Set REDU Board Property............................................................................................................3-45 Figure 3-53 Set TRX Board Type.....................................................................................................................3-46



Figure 3-56 Modify clock parameter................................................................................................................3-49

Figure 3-57 Modify equipment property of a site ..................................................................... .......................3-49

Figure 3-58 Configure Site Tower-top Amplifier ............................................................ .................................3-50

Figure 3-59 TMA configuration for the site supporting detach........................................................................3-50


4/95

M900/M1800 Base Station ControllerData Configuration Manual - Dynamic Configuration Figures


Copyright Huawei Technologies Co., Ltd.v



Figure 3-62 Modify Site Data...........................................................................................................................3-53

Figure 3-63 Site Device Property dialog box for BTS312 ........................................................... ....................3-54

Figure 3-64 Site Device Property dialog box for BTS3012 .................................................................... .........3-55



Figure 3-67 Modify site output parameter........................................................................................................3-58

Figure 3-68 Startup traffic statistics task re-register.........................................................................................3-59

Figure 3-69 Command list during dynamic setting ............................................................................ ..............3-60

Figure 3-70 Rename Site or Cell ............................................................ .......................................................... 3-61

Figure 3-71 Rename Site..................................................................................................................................3-61

Figure 3-72 Rename Cell .................................................................... ............................................................. 3-62

Figure 3-73 Rename External cell....................................................................................................................3-62

Figure 3-74 Modify 3G external cell name ......................................................................... .............................3-62

Figure 3-75 Select BIE Board (Modify Ring Topology Mark) ........................................................................ 3-65

Figure 3-76 Modify Topology Mark (Modify Ring Topology Mark)...............................................................3-66

Figure 3-77 Configure Closed Loop BIE Port..................................................................................................3-66

Figure 3-78 Dynamic Configuration (Modify Ring Topology Mark) .............................................................. 3-67

Figure 3-79 Select BIE Board (Add Slave Chain to Site) .................................................................... ............3-68

Figure 3-80 Add Slave Chain (Add Slave Chain to Site) ..................................................................... ............3-69

Figure 3-81 Select Site to Add Slave Chain (Add Slave Chain to Site) ........................................................... 3-69

Figure 3-82 Configure Site Port ........................................................... ............................................................ 3-70

Figure 3-83 Configure Inter-site Port Cascade Relationship............................................................................3-70

Figure 3-84 Select BIE Board (Delete Slave Chain of Site)...................................................... .......................3-72

Figure 3-85 Delete Slave Chain (Delete Slave Chain of Site)..........................................................................3-72 Figure 3-86 Deleted Slave Chain (Delete Slave Chain of Site)........................................................................3-73

Figure 3-87 Configure Inter-site Port Cascade Relationship............................................................................3-73

Figure 3-88 Select BIE Board (Configure Site Idle TimeSlot).........................................................................3-75

Figure 3-89 Select Site (Configure Site Idle TimeSlot)....................................................................................3-75

Figure 3-90 Configure Idle TimeSlot (Configure Site Idle TimeSlot).............................................................. 3-76

Figure 3-91 System prompt Information......................................................... ................................................. 3-76

Figure 3-92 Dynamic Configuration .......................................................... ...................................................... 3-77


5/95


6/95

M900/M1800 Base Station ControllerData Configuration Manual - Dynamic Configuration Tables


Copyright Huawei Technologies Co., Ltd.vii

Tables

Table 3-1 Relationship between port No. and TRX..........................................................................................3-10

Table 3-2 Modified data table in BSC Data Management System ................................................................... 3-20


Table 3-4 Modified data table in BSC Data Management System ................................................................... 3-37 Table 3-5 Modified data table in BSC Data Management System ................................................................... 3-41





Table 3-10 Modified data table in BSC Data Management System ................................................................. 3-63

Table 3-11 Modified data table in BSC Data Management System..................................................................3-67








7/95

M900/M1800 Base Station ControllerData Configuration Manual - Dynamic Configuration 3 BTS Data Configuration


Copyright Huawei Technologies Co., Ltd.3-1

3 BTS Data ConfigurationAbout This Chapter

The following table lists the contents of this chapter.

Section Describes

3.1 Adding a Site Describes how to add a site.

3.2 Deleting a Site Describes how to delete a site.

3.3 Adding TRX Describes how to add a TRX.

3.4 Deleting TRX Describes how to delete a TRX.

3.5 Adding or Deleting Board Describes how to add or delete a board.

3.6 Modifying Board Type Describes how to modify the board type.

3.7 Configuring Site Tower-topAmplifier

Describes how to configure the site tower top amplifier.

3.8 Modifying Site Data Describes how to modify site data.

3.9 Modifying Site's OutputProperty

Describes how to modify the site output property.

3.10 Starting up Traffic Stat.Task Re-register

Describes how to startup traffic stat. task re-register.

3.11 Renaming Site or Cell Describes how to rename a site or cell.

3.12 Modifying Ring TopologyMark

Describes how to modify a ring topology mark.

3.13 Adding Slave Chain to Site Describes how to add a slave chain to a site.

3.14 Deleting Slave Chain ofSite

Describes how to delete a slave chain of a site.

3.15 Configuring Site Idle

Timeslot

Describes how to configure site idle timeslots.


8/95

3 BTS Data ConfigurationM900/M1800 Base Station Controller


3-2Huawei Proprietary and Confidential


Section Describes

3.16 Batch Process Site Property Describes how to modify site properties in batches.

3.17 Modifying Site BoardParameters

Describes how to modify site board parameters.

3.18 Adding or Deleting a BreakPoint

Describes how to Adding or Deleting a Break Point.


9/95




This chapter introduces operations to BTS data. Including adding/deleting site,adding/deleting TRX, adding/deleting BTS board, modifying board type, modifying sitetower-top amplifier, modify site data, modifying sites output property, starting-up trafficstatistic task re-register, renaming site or cell, modifying ring topology mark, adding slavechain to site, deleting slave chain of site, configuring site idle timeslot.

3.1 Adding a Site

FunctionThis function is used to add a site online. There is no need to reset BSC.

Under chain and tree networking, if the new site fails to normally operate, it is recommendedthat sites on the chain where this site can be located be reset successively from the one at theuppermost level. In addition, BIE can also be reset. Check the correctness of the dataconfiguration.

After successfully adding a site, re-register the traffic statistics tasks of this site by selectingthe [BTS/Startup Traffic Stat. Task Re-register].

If the new site is the first added site of BIE port, and the newly added site can not work, needsto reset the BIE.

PreparationStep 1 Make sure that there are idle E1 ports on BIE.

Step 2 Adding site involves most of the BSC data. Before dynamic configuration, do check the dataconfiguration carefully to avoid data inconsistency or data error.

Step 3 Only one site can be added to one BIE port by one dynamic configuration operation. If theTRX of the new site is distributed over multiple chains, the operation of adding TRX oradding cell should be performed after the site is successfully added.

Step 4 The adding a cell operation has been performed during the process of the Adding a Siteoperation. Select the [Cell/ Modify Cell Handover Parameter] to implement "Modify Cell

Handover Parameter" operation to configure cell adjacency relationship after the successfullyadding a site.

----End

Procedure without the TS Manual AdjustmentFor example, add a site Site2, TRX0, TRX3, TRX5, TRX8, TRX18, TRX21 and TRX24 inBM1 for two cells. Cell1 includes TRX0, TRX5, TRX18 and TRX24 and Cell2 includesTRX3, TRX8 and TRX21. Cell1 and Cell2 are bi-directionally adjacent. No TS manualadjustment is required for the new site. And the new site is connected to port0 of BIE0, withtrunk mode as 2E1 port*15:1multiplexing/port.


10/95





Step 1 Select the [BTS/Add a Site], the interface will pop up as shown in Figure 3-1 .

Figure 3-1 Selecting the board and the module containing the board in [Add a Site]

Select the module and the BIE.

The button will become usable.

Step 2 Click , the interface will pop up as shown in Figure 3-2 .

Figure 3-2 Add a site

The trunk mode can not be modified unless no sites have been connected to the any port ofBIE board.


11/95




Select Port [0] the BIE port connected to the BTS, and Site0 the site of upper level to add site.Then click to enter the interface shown in Figure 3-3 .

Figure 3-3 Add site

The BTS3012, BTS3012AE, BTS3012II, and BTS DBS3900 GSM all support physical TRX boards andthe logical configuration detach function. For the BTS3012, BTS3012AE, BTS3012II, you can select thesupporting detach option on the interface to determine whether a BTS supports the detach function.

For details on the configuration modes, refer to section 6.3 Introduction of the BTS3012 and ItsConfiguration in the M900/M1800 BSC Data Configuration Manual-Initial Configuration .

Having chosen the site type BTS 312, BIE port of upper level, click to pop up theinterface as shown in Figure 3-4 .

Figure 3-4 Select mode

Click to complete the Adding Site.


12/95


13/95




Figure 3-6 Add TRX

Select 0 TRX, 3 TRX, 5 TRX, 8 TRX, 18 TRX, 21 TRX and 24 TRX in theAvailable TRX list box, and then click to add them into the Installed TRXlist box.

Step 4 Click , the interface will appear as shown in Figure 3-7 .

Figure 3-7 Adding cell in [Add a Site]


14/95





Step 5 Click to pop up the interface as shown in Figure 3-8 .

Figure 3-8 BTS equipment property configuration

Select a rack from the Current Rack drop-down list box and remove the redundant boardsfor the rack. Double-click the antenna property configured for the CDU board. Then, clickBTS Property to configure the property for the BTS. Finally, click Site Rack Config toconfigure the racks and cabinet groups.

The cross-TRX cabinet group is added, and therefore you must set the intra-site relation. Theconfiguration interface is shown in Figure 3-10 . For the site supporting the detach function,you must configure the cabinet groups and racks before setting the intra-site relation.

Step 6 For the site supporting detach, the primary rack (No.0 Rack) in the primary cabinet group isautomatically created by default. Click Site Rack Config on the Site Device's Propertyinterface to manually configure other cabinet groups, as shown in Figure 3-9 .


15/95




Figure 3-9 Configuring cabinet groups and racks

Click OK and the interface returns to Figure 3-8

Click Complete and the interface returns to Figure 3-7 .

Click Intra-site Link . The Modify Site Internal Connections dialog box is displayed, asshown in Figure 3-10 .

Figure 3-10 Site internal connections configuration


16/95





Configure the site internal connections according to the actual demand. The relations between port No. and TRX are shown in Table 3-1 .

Table 3-1 Relationship between port No. and TRX

Cabinetgroup No. Port No.

No. of TRXcorresponding to BTS30

No. of TRX correspondingto BTS312

0 07 017 023

1 811 1835 2447

2 1619 3653 4871

Click , the interface will return to Figure 3-8 .

Click , the interface will return to Figure 3-7 .Step 7 Click to add two cells. See Figure 3-11 .

Figure 3-11 Add cell

Input the related information on newly added cells.

To name a cell, you must comply with the following principles: If the number of cells to be added is greater than 1 or the Name Cell by Site's Name check box is

selected, the cell name cannot be edited. If the Name Cell by Site's Name check box is selected, the format of the cell name is "site

name-suffix number." For example, the previously added cells, Site 2-1 and Site 2-2. If the number of cells to be added is greater than 1 or the Name Cell by Site's Name check box is

not selected, the format of the cell name is "cell-cell number." The default cell template is used for added cells, but the system also supports a custom cell template.

For details, see chapter 4 "Cell Data Configuration."


17/95




Click , the two cells added will be listed in the Cell List box as shown in Figure 3-12 .

Figure 3-12 Add a site (add cells)

Step 8 Select the cell Site2-1 and Click and the interface will pop up asshown in Figure 3-13 .

Figure 3-13 Set cell property

As shown in Figure 3-13 , assign No.3, 5 TRX as well as properties such as usable frequencyand network parameters to Site2-1.


18/95





For the site supporting detach, you must bind the logical TRX to the relevant physical TRX board after configuring the cell properties. If the logical TRX is not bound to the relevant physical TRX board, you must manually add a physical TRX board or add a rack.

In Figure 3-7 , click BTS Property . Then, in the displayed interface, right-click an empty slot

of the TRX subrack. The types of the physical TRX boards that can be configured aredisplayed, as shown in Figure 3-14 .

Figure 3-14 Adding boards

Then, bind the TRX to the added physical TRX board of the corresponding rack. Double-clickDTRU board or QTRU board , the Configure Physical Board Attributes dialog box isdisplayed, as shown in Figure 3-15 .


19/95




Figure 3-15 Binding TRXs

Select a cell name and a TRX No. and then click TRX Prop . The TRX Property dialog box isdisplayed, as shown in Figure 3-16 .


20/95





Figure 3-16 Configuring TRX property

After completing the configuration, click OK to return to the current interface. Thus, the property of the physical TRX board is configured.

For more details about advance property configuration of the cell, please refer to 4.1 Addinga cell in Chapter 4.

In Figure 3-12 , select the cell and click to delete it.


Step 9 The procedure of adding TRXs to Site2-2 is the similar as that to Site2-1 described above.

Step 10 Configure all cell data and make sure that all TRX are assigned to cell.

Step 11 Click in Figure 3-12 to modify the reserved parameters ofnewly added site, cell and TRX, the interface as shown in Figure 3-17 will pop up.


21/95


22/95





Now the configuration of adding a site without the TS manual adjustment is finished.

----End

Procedure with the TS Manual AdjustmentStep 1 In Figure 3-4 , click , the interface will pop up as shown in Figure 3-19 .

To manually adjust timeslot, please refer to 7.4 TS manual adjustment in M900/M1800 Base StationController Data Configuration Manual - Initial Configuration.

Figure 3-19 Check [Manual Mode]

A Manual Mode check box will appear in the interface. Select the Manual Mode.

Step 2 Click , the operation of Add TRX and Add cell is same as that in Procedurewithout the TS Manual Adjustment .

Step 3 After successful adding cells, the TS manual adjustment interface will pop up, as shown inFigure 3-20 .

Figure 3-20 Timeslot manual adjustment interface


23/95




In Figure 3-20 , all sites on the main chain of the newly-added sites are listed. All TRX pro perties (e.g ., Abis TS No., Abis sub-TS No. and trunk circuit No., etc.), RSL and OML properties of the new sites must be input manually for the manual adjustment of timeslots. Ifsites cascading is involved, site trunk mode and BIE port property must also be configured.

Step 4 Select the new site and click in Figure 3-20 , the interface will pop up asshown in Figure 3-21 .

Figure 3-21 TRX Property

The properties listed in Figure 3-21 have default values before they are modified, e.g., theAbis TS No. and Abis Sub-TS No. are 0, the Trunk circuit No. is 65535 and the BSC BIE E1TimeSlot No. is 255.

Rev. OML Trunk Circuit No., Rev. OML ABIS TS No., Rev. OML BSC BIE E1 TS No. andRev. OML Physical Link No.are usable if relay mode of BIE board is full rate ring topologyor half rate ring topology.

Under TS manual adjustment mode, the physical links of RSL and OML should not bemodified and they are automatically calculated by system.

One dynamic configuration can only modify the TRX properties of the new site, and view but notmodify the TRX properties of other sites.

RSLs are multiplexed according to Abis TS No. input by the user, so data must be correct under TSmanual adjustment mode.

When the value in Idle Timeslot Number in Figure 3-21 exceeds 0, in Figure 3-20 will be usable. Click the button to view the idle timeslot distribution of the selected site.

Step 5 Modify the RSL properties of all the new TRXs.


24/95


25/95




Figure 3-23 Site trunk mode configuration

For the detail information on the parameters, please refer to M900/M1800 Base StationController Data Configuration Reference - Engineering Parameters.

Trunk Mode No. in Figure 3-23 should be the upper site number multiplies two. If relay mode of BIE board is full rate ring topology or half rate ring topology, the Rev. Trunk Mode

No. should be the upper site number multiplies two plus one. The BIE trunk modes of all the sites connected to all the BIE ports are listed in Figure 3-23 .


Step 7 Click in Figure 3-20 and the interface will pop up as shown in Figure3-24 .


26/95





Figure 3-24 BSC BIE description data configuration

For the detail information on the parameters, please refer to M900/M1800 Base Station

Controller Data Configuration Reference - Engineering Parameters.Modify the Abis interface and BS interface properties of BSC BIE ports according to theactual demand. After modifying the trunk data of BIE, plug out and plug in the BIE to enablethe data.


Step 8 Click in Figure 3-20 to enter the dynamic configuration interface.

Step 9 Click to implement the dynamic setting of adding a site toGMPU.

----End

Verification

Step 1 After the node icons of the newly added site are displayed on the OMC SHELL, start the SiteMaintenance System of the newly added site. If all carriers are powered on and in normalcondition, all channels in a cell will be in idle status.

Step 2 Calls made in newly added sites can be established.

----End

Data TableThe modified data tables in the BSC Data Management System are listed in Table 3-2 .

Table 3-2 Modified data table in BSC Data Management System

list Table name

1 [HWII power control table]

2 [BSC Cell table]

3 [TRX Configuration Table]

4 [Radio Channel Configuration Table]


27/95




list Table name

5 [LAPD Semi-perm. Connection Table]

6 [LAPD Signaling Connection Table]

7 [BSC BIE Active/Standby Group Table]

8 [BSC BIE Description Table]

9 [Site BIE Trunk Mode Description Table]

10 [Site BIE Configuration Table]

11 [Signaling Channel Link Table]

12 [System Information Table]

13 [Cell Configuration Table]

14 [Normal handover table]

15 [Cell Allocation table]

16 [BA1(BCCH) table]

17 [BA2(SACCH) table]

18 [Cell Attribute Table]

19 [Cell Alarm Threshold Table]

20 [Cell Call Control Table]

21 [Cell Call Control Parameter Table]

22 [Cell Module Information Table]

23 [Handover Control Table]

24 [Load Handover Table]

25 [Intra-cell cont. HO ctrl. table]

26 [Penalty Table]

27 [Filter Table]

28 [Emergency Handover Table]29 [Adjacent Cell Relation table]

30 [Power Control Selection Table]

31 [BTS Power Control Table]

32 [MS Power Control Table]

33 [Radio CH Management Ctrl. Table]

34 [Site Description Table]

35 [Site Slot Description Table]


28/95





list Table name

36 [Carrier Configuration Table]

37 [External Cell Description Table]

38 [Fast-moving Handover Table]

39 [Cell Module Information Table]

40 [Frequency Hopping Table]

41 [Site Frame Description Table]

42 [HW II Channel Allocation Table]

43 [Antenna and Feeder Configuration Table]

44 [Concentric Cell Handover Table]

45 [Site Software Configuration table]

46 [Site Reserved Parameter Table]

47 [Cell Reserved Parameter Table]

48 [TRX Reserved Parameter Table]

49 [3G BA1Table]

50 [3G System Information Data Table]

51 [3G Inter System HO Data Table (UTRAN FDD)]

52 [UTRAN FDD Cell Adjacent Relationship Table]

53 [3G Filter Data Table]

54 [3G BA2 Table]

55 [LAPD Cell Reserved Parameter Table]

3.2 Deleting a Site

FunctionThis function is used to delete sites no longer needed. When sites are deleted, all the cellsconnected to them will also be deleted.

After deleting a site, the corresponding icon on the OMC Shell operation interface should be

deleted.


29/95




Preparation

Step 1 Before site deletion, block all cells through Site Maintenance System. This can avoidconversations remaining in the site during deletion.

Step 2 Only one site can be deleted each time. If the site to be deleted contains sub-sites cascaded,the sub-sites cascaded must first be deleted.

Step 3 If the site to be deleted is not the first level site connected to BIE port and BIE port is in thetimeslot manual adjustment mode, the BIE trunk mode of the site must be modified manually

by implementing TS manual adjustment operation.

----End

ProcedureFor example, to dynamically delete Site2 in BM1 (the BIE port of Site2 is in the TS manual

adjustment mode and Site2 is the sub-site of Site0.Step 1 Select the [BTS/Delete a Site], the interface will pop up as shown in Figure 3-25 .

Figure 3-25 Delete a site - select site

Select Site2 to be deleted.

If no site is selected or the site selected is not the last level site, in Figure 3-25 will be unusable.

Step 2 Click to enter the interface as shown in Figure 3-26 .


30/95





Figure 3-26 Delete site (timeslot manual adjustment)

All the sites connected to the BIE port of the site, (Site2 in BM1) to be deleted will be listedin the list box. If the connection is in multi-chain mode, all the sites of the main chain BIE

port will be listed. However, the site to be deleted will not be listed.

If the BIE port connected to the selected site is not in TS manual adjustment mode, the dynamicconfiguration interface instead of timeslot manual adjustment interface will pop up.

The button is usable, if the idle timeslot of the selected site is not 0.

Select the last site in the list box, click in Figure 3-26 tomanually modify the site BIE trunk mode as shown in Figure 3-27 .


31/95




Figure 3-27 Delete site (site BIE trunk mode)


Site BIE Trunk Mode Description of Site2 can be deleted manually, i.e., all the records of thesite with Trunk Mode No. as 0 can be deleted by pressing .


32/95





In Figure 3-26 , click to view the site TRX property. See Figure 3-28 .

Figure 3-28 Delete site (site TRX property)

The TRX properties of Site0 are listed in Figure 3-28 .

Any parameter, such as Abis TS No. and Abis Sub-TS No., is not advised to be modified.

Step 3 Click to enter the dynamic configuration interface as shown in Figure 3-29 .

Figure 3-29 Command list for dynamic setting

Step 4 Click to implement the dynamic setting of deleting a site toGMPU.


33/95




Because there are many adjacent cells for any cell under a site, and the adjacent relationship between thecells will be deleted after a BTS has been deleted. Therefore, the "configure handover data" commandmust be executed to automatically update the adjacent relationship for the cells adjacent to the deletedcell.

----End

VerificationMaintenance for sites deleted is not available on OMC SHELL. The system prompts error sitenumber. OMLs and RSLs corresponding to the sites have already been released in switchingnetwork boards.


3.3 Adding TRX

FunctionThis function is used to add carrier to the designated site. Usually used for cell capacityexpansion.

In the case of star and tree networking, if the new TRX or other equipment fails to operate, itis recommended that BTSs on the link where this site can be located be reset successivelyfrom the one at the uppermost level. In addition, BIE can also be reset. Check the correctnessof the data configuration.

After successfully adding a TRX, the traffic statistics tasks of this site should be re-registered.

Preparation

Step 1

Before adding the TRX, block the TRX from Site Maintenance System.Step 2 TRX can only be added to one site connected to one BIE port by one dynamic configuration.

To add multiple TRXs to multiple sites or to multiple BIE ports of one site, please first perform "Add TRX" operation to one site connected to one BIE port, and then repeat theoperation.

Step 3 If the BIE port of the site to be added with TRX is in the TS manual adjustment mode, perform timeslot manual adjustment operation to adjust the frequency information of the site.

----End


34/95





ProcedureFor example, to add No.1 and No. 7 TRX to Site0-1 and Site0-2 under Site0 in BM1. The BIE

port corresponding to Site0 is in the timeslot manual adjustment mode.

Step 1 Select the [BTS/Add TRX], and the [Add TRX] interface will pop up as shown in Figure3-30 .

Figure 3-30 Select site

Select Site0 in BM1.

The button in Figure 3-30 is unusable, if no site is selected.


Figure 3-31 Add TRX


35/95




Select 12TRX and 17TRX, and click , the 1TRX and 7TRX will be added to theinstalled TRX box.

All the BIEs and BIE ports connected to the site are respectively listed in the [BIE the Site Belongs

to] drop-down box, and [Select]. Select the BIE and BIE port bearing the new TRX. However [BIEthe Site Belongs to], and [Select] are not available if there is TRX in the Installed TRX list, so thatTRX can only be added to one port of one BIE for each operation.

If the number of added TRXs exceeds 4, a dialogue box is displayed showing the message Numberof new added TRX is more than 4. It will reset site! Continue(Yes/No)?.


Figure 3-32 Configure cell

It is not allowed to add or delete the existed cells at this step. If the internal transparent transmission relationship gets changed because of the new TRXs, e.g., for

BTS30, there have been only TRX1 and TRX4, but now TRX18 is added to it, click to configure the site internal connections. For more details of site internal connectionconfiguration, refer to 3.1 Adding a Site .

Select a cell in [Cell List] then click to configure the cell property forthe cells in list as shown in Figure 3-33 .


36/95





Figure 3-33 Assign TRX to cell

Use Modify CA, user can add frequency to the Cell.

For the site not supporting detach, double-click 12 TRX . In the displayed interface related toconfiguration of the TRX property, assign valid frequency points for 12 TRX .

For the site supporting detach, switch to the interface related to configuration of the BTS

property and add racks or physical TRX boards as required. Also, on the interface related tothe available rack, you can right-click a physical TRX board to be added or select theavailable physical TRX. Then, bind the added TRX to the idle channels of the physical TRXand assign valid frequency points for the TRX. For the detailed configuration procedure, seesection 3.1 "Adding a Site ."


Assign No.7 TRX and assign available frequencies to Site0-2 according to the steps describedabove.

Click to modify newly added TRXs reserved parameters,otherwise these parameters have default value: 65535.

Click Modify Reserved Parameters to modify the reserved parameters of the added TRX. If theyare not modified, all the parameter values are 65535 by default.

If a TRX is not assigned to the cell, the Next button in Figure 3-32 is dim. When adding TRXs for a detach site, you cannot modify the original binding relation. If the original physical TRX boards include the DTRU boards and idle channels are available, the

added TRX is automatically bound to the corresponding DTRU board.


37/95




Step 4 Click in Figure 3-32 , the timeslot manual adjustment interface will pop up as shownin Figure 3-34 .

Figure 3-34 Timeslot manual adjustment

Select the newly-added site in the list box, and then respectively click , , to configure related properties.

For detailed configuration procedures, refer to section 6.1.5 Adding TRX in theM900/M1800 BSC Data Configuration Manual-Initial Configuration.

In the TRX property interface after clicking as shown in Figure 3-34 , onlythe TRX properties of the BIE port and the site can be modified and the properties of otherBIE ports or sites cannot be modified. This principle is applicable to all dynamicconfiguration operations.

If the BIE port of the BIE bearing the TRX added is not in the TS manual adjustment mode, enterthe dynamic configuration interface as described in 3.1 Adding a Site .

For more details of TS manual adjustment, please refer to 3.1 Adding a Site .

Step 5 Click to enter the dynamic configuration interface.

Step 6 Click to implement the dynamic setting of adding TRX toGMPU.

----End

Verification

Step 1 Check through the Site Maintenance System to see if the TRX added is in normal status.

Step 2 Test the conversation via the new TRX with test MS.

Step 3 Check the data tables and the host to see whether the related data has been correctly modified.

----End


38/95







list Table name









9 [LAPD Semi-perm. Connection Table]





14 [BA1(BCCH) Table]

15 [BA2(SACCH) Table]




3.4 Deleting TRX

FunctionThis function is used to delete a faulty carrier of a BTS, or to adjust the capacity of the cellswithin the same site.


39/95




In the case of star and tree networking, if system fails to operate normally, it is recommended

that BTSs on the link where this site can be located be reset successively from the one at theuppermost level. In addition, BIE can also be reset. Check the correctness of the dataconfiguration at the same time.

After successfully deleting a TRX, the traffic statistics tasks of this site should bere-registered.

Preparation

Step 1 Block the TRX at the Site Maintenance System before deleting it in case there is still ongoingsession on the TRX.

Step 2 To delete the TRX configured with main BCCH of the cell, first select the [Cell/ModifyTRXs Channel Type] to modify the channel type as non-main BCCH and assign a newBCCH to the cell. If the main BCCH is the last one in the cell, select the [Cell/Delete Cell] todelete the cell.

Step 3 If the cell is configured with the function resources reservation for priority , and the numberof full rate channel it can provide is smaller than that reserved after deleting the TRXs,modify the reserved channel number first.

Step 4 Only TRXs (except the TRX configured with main BCCH) of one cell in one site can bedeleted for one deletion. To delete TRXs in different sites or to delete TRXs of different cellsin the same site, select [BTS/Delete TRX] to delete the TRX repeatedly.

Step 5 For BTS20, the corresponding FPU will also be deleted when TRX is deleted. For

BTS3002C-204, the corresponding MFU will also be deleted when TRX is deleted.Step 6 After the TRX is deleted, the rack will be deleted except for rack0 if there is no TRX on it.

Step 7 If the BIE port of the site in which TRX is to be deleted is in timeslot manual adjustmentmode, timeslot should be adjusted manually when deleting TRX. For more details of timeslotmanual adjustment, refer to 3.1 Adding a Site or 3.3 Adding TRX .

----End

ProcedureTo delete No.18 and No.21 TRXs of Site2 in BM1. The two TRXs are assigned to Site2-1which contains 3 TRXs, No.0, No.18 and No.21 TRXs.

Step 1 Select the [BTS/Delete TRX], and the [Delete TRX] interface will pop up as shown in Figure3-35 .


40/95





Figure 3-35 Select cell

Select Site2-1 of the TRX to be deleted.

The button in Figure 3-35 is unusable, if no cell is selected.


Figure 3-36 Select TRX

Select 8 TRX and 10 TRX and click > to add them to the Deleted TRX list box.



41/95


42/95





Figure 3-39 Modify the reserved channel number

Modify the parameter Correct the Reserved Channel Number.


Figure 3-40 Command list for dynamic configuration

Step 5 Click to implement the dynamic setting of deleting TRX toGMPU.

If the BIE port of the site in which TRX is to be deleted is in TS manual adjustment mode, timeslotshould be adjusted manually when TRX is deleted. For more details of timeslot manual adjustment, referto 3.1 Adding a Site or 3.3 Adding TRX .


43/95




----End

Verification

Check to see if the designated TRXs have been deleted.



list Table name









9 [LAPD Semi-perm. Connection table]





14 [BA1(BCCH) Table]

15 [BA2(SACCH) Table]




19 [Radio Channel Management and Control Table]

20 [Channel Assignment Algorithm II Data Table]


44/95





3.5 Adding or Deleting Board

Function

This operation is used to delete the:

Standby TMU and standby OMU PSU, PMU, APMU, DPMU, EAC, DEMU, EMUA, EMU, PBU, CDU, EDU, TES, TEU,

MCK, HPA, DATU, DHEU and IASU. Physical TRX boards not bound

It is not allowed to delete the active TMU/ active OMU /TRX/FPU/MFU/MMU.FPU in BTS20 and MFU in BTS3001C cannot be separately deleted. Only when the TRX isdeleted, these boards will also be deleted.

Site output property and extended parameter will be adjusted as the default value whenEAC/DEMU/EMUA/EMU is deleted. For more details, please refer to 3.8 Modifying Site and 3.9Modifying Site's Output Property .

Preparation None.

Procedure

Step 1 Select the [BTS/Add or Delete Board], and the [Add or Delete Board] interface will pop up asshown in Figure 3-41 .



45/95




Select the site for which the board will be added/deleted.


Figure 3-42 Add/delete board

Step 3 Click Add/Delete BTS Board to add or delete boards on the interface related to BTShardware configuration. Right-click a board to be deleted and choose Delete Board from theshortcut menu. The board is directly deleted, as shown in Figure 3-43 and Figure 3-44 . To add

boards, you can right-click in the black area of the interface.

Figure 3-43 Deleting boards for the site not supporting detach


46/95





Figure 3-44 Deleting boards for the site supporting detach

For the BTS supporting detach, only the physical TRX boards not bound to TRXs can beadded or deleted. If the board to be deleted has a binding relation, a prompt box is displayed,as shown in Figure 3-45 .

Figure 3-45 Prompt box

TRX cannot be deleted in this operation.



47/95






Step 5 Click to finish the adding/deleting boards to/from the site.

----End

VerificationBoard status is normal when viewed from the Site Maintenance System.

Check the data tables and the host to see whether the related data has been correctly modified.



list Table name






48/95





3.6 Modifying Board Type

Function

This operation is used to online modify the type of CDU, EDU, DDPU, DDPM, FCU, DFCU,DCOM, TRX, PBU, DTRU, or APMU.

Preparation None.

Procedure

Step 1 Select the [BTS/Modify Board Type], and the [Modify Board Type] interface will pop up asshown in Figure 3-47 .

Figure 3-47 Select Site (Modify Site Board Type)

Select the site for which the board type will be modified.



49/95




Figure 3-48 Modify Board Type (Modify Site Board Type)

Click , the interface will be shown in Figure 3-49 .

Figure 3-49 Site Devices Property


50/95





Step 3 Double click PBU board to enter the interface as shown in Figure 3-50 .

Figure 3-50 Set PBU Board Property

Modify the parameter PBU Card Type.


Step 4 Double click CDU board to enter the interface as shown in Figure 3-51 .

Figure 3-51 Set CDU Board property

Modify the parameter CDU Type.



51/95




Step 5 Double click EDU board to enter the interface as shown in Figure 3-52 .

Figure 3-52 Set REDU Board Property

Modify the parameter CDU Type.



52/95





Step 6 Double click TRX board to enter the interface as shown in Figure 3-53 .

Figure 3-53 Set TRX Board Type

Modify the parameter TRX Type.


TRX types and TRX frequencies are restricted. The PTRX frequencies must be in the range of 1 to124. The ETRX frequencies must be in the range of 0 to 124 or 975 to 1023. The RTRX frequenciesmust be in the range of 0 to 124 or 955 to 1023. The DTRX frequencies must be in the range of 512to 885. The DDPU, DDPM, DFCU, FCU, and DCOM boards support modification of frequency

band types. Other boards support modification of only board types. Only TRXs with even numbers can be modified. For example, when TRX0 exists, but TRX1 doesnot exist, TRX0 can be changed to DTRU. When TRX1 exists, however, TRX1 cannot be modified.

If the original physical TRX boards include the DTRU boards and idle channels are available, theadded TRX is automatically bound to the idle channel of the corresponding DTRU board. Forexample, when TRX0 exists and the board type is DTRU, TRX1 is automatically bound to the sameDTRU if the board type of TRX1 is changed.



53/95




Step 7 Click to enter the interface as show Figure 3-54 .


Step 8 Click to finish the modification.

----End

VerificationCheck the data tables to see whether the related data has been correctly modified.



list Table name



54/95


55/95




Figure 3-56 Modify clock parameter

Click to enter the interface shown in Figure 3-57 .

Figure 3-57 Modify equipment property of a site


56/95





Double click CDU (or EDU) to enter the interface shown in Figure 3-58

Figure 3-58 Configure Site Tower-top Amplifier

For detach sites, you need to configure the physical TRX board number and logical channelnumber bound to the logical TRX for the antenna connection relation displayed on theinterface related to tower mounted amplifier (TMA) configuration, as shown in Figure 3-59 .

Figure 3-59 TMA configuration for the site supporting detach


57/95




When configuring the antenna connection for the QTRU board, you need to select only the physicalTRX board number corresponding to the logical TRX rather than the channel number.

When configuring the antenna connection for the DTRU board, you must select both the physicalTRX board number and the channel number corresponding to the logical TRX


Configure Site Tower-top Amplifier.

Click to complete the modification and the interface will return to Figure 3-57 .


Step 3 Click to enter the interface as show Figure 3-60 .


Step 4 Click to finish the configuration.

----End

Verification

The Tower-top Amplifier is correctly modified when viewed from the Site MaintenanceSystem.



list Table name



58/95





3.8 Modifying Site Data

Function

This operation is used to online modify the clock mode, clock parameter, alarm shielding property, and transmission mode of the site. If[[the old board parameter of BTS 20] ismodified, 4th level reset command will be sent from BSC Data Auto Configuration System.

Preparation None.

Procedure

Step 1 Select the [BTS/Modify Site Data], the [Modify Site Data] interface will pop up as shown inFigure 3-61 .


Select the site for which the clock parameters will be modified.



59/95




Figure 3-62 Modify Site Data

Step 3 Click Modify Site Data .

The configuration interfaces vary with the site types. For the BTS312, the Site DeviceProperty dialog box is displayed, as shown in Figure 3-63 . For the BTS3012, BTS3012II,and BTS3012AE, you can set the sites to support detach by selecting the support detachoption. Accordingly, the Site Device Property dialog box is displayed, as shown in Figure3-64 .


60/95





Figure 3-63 Site Device Property dialog box for BTS312


61/95




Figure 3-64 Site Device Property dialog box for BTS3012

You can only change the site type from not supporting detach to supporting detach, and you cannotchange the site type from supporting detach to not supporting detach.



Step 4

Click to enter the dynamic configuration interface as shown in Figure 3-65 .


62/95






Step 5 Click to implement dynamic setting of modifying site data toGMPU.

----End

VerificationThe clock parameter is correctly modified when viewed from the Site Maintenance System.



list Table name



3 [BSC BIE Active/Standby Group Description Table]



63/95




3.9 Modifying Site's Output Property

Function

This operation is used to online modify the EAC relay status of the site. This operation canonly be implemented to the site configured with EAC/DEMU/DEMUA/EMU.

PreparationMake sure that the site whose output properties are to be modified has been configured withEAC/DEMU/DEMUA/EMU. If no EAC/DEMU/DEMUA/EMU is configured to the site,select the [BTS/Add or Delete Board] described in 3.5 Adding or Deleting Board to add anEAC/DEMU/DEMUA/EMU.

Procedure

Step 1 Select the [BTS/Modify Site's Output Property], the interface will pop up as shown in Figure3-66 .


Select the site for which the output property is to be modified.



64/95





Figure 3-67 Modify site output parameter

Step 3 Click to modify EAC relay status.

Step 4 Click in Figure 3-67 to proceed after modifying EAC relay status to enter thedynamic configuration interface.

Step 5 Click to implement the dynamic setting of modifying siteoutput property to GMPU.

----End

VerificationSelect the [Start/Task/Data Management] to run BSC Data Management System to check the[Site/Site Description Table].



list Table name



65/95




3.10 Starting up Traffic Stat. Task Re-register

FunctionThis operation is used to start up traffic statistics task re-registration online. This function isusually used to renew the permanent traffic statistics task. It is usually used for some criticaloperations that impacts cell handover relationship, e.g., to dynamically add/delete a site,add/delete TRX, add/delete a cell, modify cell adjacency relationship and modify CGI etc.

Preparation None.

Procedure

Step 1 Select the [BTS/Startup Traffic Stat. Task Re-register], and the interface will pop up as shownin Figure 3-68 .

Figure 3-68 Startup traffic statistics task re-register

Select startup mode.



66/95





Figure 3-69 Command list during dynamic setting

Step 3 Click to implement the dynamic setting of starting up trafficstatistics task re-registration to GMPU.

No modification of any data table is related to this operation.

----End

3.11 Renaming Site or Cell

FunctionThis function is used to rename site or cell. All sites and cells can be renamed in one dynamicoperation.

Preparation None.

Procedure

Step 1 Select the [BTS/Rename Site or Cell]. The interface will pop up in Figure 3-70 .


67/95




Figure 3-70 Rename Site or Cell

Step 2 Rename site.

Select the site that need be renamed, and then click in Figure 3-70 .Rename dialog box will be shown in Figure 3-71 .

Figure 3-71 Rename Site

Modify the parameter of Site Name.


Step 3 Rename cell, external cell or 3G external cell.

Select the cell that need be renamed, and then click in Figure 3-70 .Rename dialog box will be shown Figure 3-72 or Figure 3-73 or Figure 3-74 according to thetype of the selected cell.


68/95





Figure 3-72 Rename Cell

Figure 3-73 Rename External cell

Figure 3-74 Modify 3G external cell name


69/95




Modify the parameter of Cell Name.


Site, cell or external cell all can be renamed in Figure 3-70 .Step 4 Click to enter the dynamic configuration interface.

Step 5 Click to implement the dynamic configuration of renamingsite or cell.

----End




list Table name

1 [BSC Cell Table]





6 [System Information Table]

7 [Cell Configuration Table]

8 [Normal Handover Table]

9 [Cell Allocation Table]

10 [BA1 (BCCH) Table]

11 [BA2 (SACCH) Table]


13 [Cell Alarm Threshold Table]


15 [Cell Call Control Parameter Table]

16 [Cell Description Table]

17 [Handover Control Table]

18 [Load Handover Table]


70/95





list Table name

19 [Intra-cell Continuous HO Control Table]

20 [Penalty Table]

21 [Filter Table]

22 [Emergency Handover Table]

23 [Adjacent Cell Relation Table]

24 [Power Control Selection Table]

25 [BTS Power Control Table]

26 [MS Power Control Table]

27 [Radio Channel Management Control Table]




31 [Fast-moving Handover Table]


33 [HW II Channel Allocation Table]

34 [Site Reserved Parameter Table]

35 [Cell Reserved Parameter Table]


37 [External Cell Description Table]

38 [Cell Adjacent Relationship Table]

39 [3G BA1 Table]

40 [3G BA2 Table]

41 [3G System Information Data Table]

42 [3G Inter System HO Data Table(UTRAN FDD)]43 [UTRAN FDD Cell Adjacent Relationship Table]

44 [3G Filter Data Table]

45 [UTRAN FDD Cell Description Data Table]

46 [Half Permanent Connection Table]


71/95




3.12 Modifying Ring Topology Mark

Function

This function is used to modify ring topology mark. For example, add or delete reverse ring port in ring topology.

Preparation None.

Procedure

Step 1 Select the [BTS/Modify Ring Topology Mark], and the interface will pop up in Figure 3-75 .

Figure 3-75 Select BIE Board (Modify Ring Topology Mark)

Select BIE board to activate button .

Only the BIE board whose relay mode is full rate ring topology or half rate ring topology can be selectedin Figure 3-75 .



72/95





Figure 3-76 Modify Topology Mark (Modify Ring Topology Mark)

First select BIE port that need modify ring topology mark. If the selected BIE port has alreadyreverse ring port, the button will be usable and the button will be unusable, otherwise the button will be usableand the button will be unusable.

Only one BIE ports ring topology mark can be modified in one dynamic operation.

Step 3 Adding topology mark

In Figure 3-76 , selecting BIE port, and then select the site that will connect to reverse ring port, click to enter the interface shown in Figure 3-77 .

Figure 3-77 Configure Closed Loop BIE Port

Select closed loop BIE port.


Step 4 Deleting topology mark

In Figure 3-76 , selecting BIE port, and then click to delete reverseBIE port.



73/95


74/95





3.13 Adding Slave Chain to Site

Function

This function is used to add slave chain to site.

Preparation None.

Procedure

Step 1 Select the [BTS/ Add Slave Chain to Site], and the interface will pop up as shown in Figure3-79 .

Figure 3-79 Select BIE Board (Add Slave Chain to Site)


Only the BIE board which has one port has not been configured at least can be selected in Figure 3-79 .

Step 2 Click in Figure 3-79 , the interface will be shown in Figure 3-80


75/95




Figure 3-80 Add Slave Chain (Add Slave Chain to Site)

Select BIE port that will be used to add a chain.

Click , the interface will be shown in Figure 3-81 .

Figure 3-81 Select Site to Add Slave Chain (Add Slave Chain to Site)


76/95





Select the site which the slave chain will add to, Click to enter the interface shown inFigure 3-82 .

Figure 3-82 Configure Site Port

Select the Access Port No. in Target Site.


Step 3 Click to enter the interface shown in Figure 3-83 .

Figure 3-83 Configure Inter-site Port Cascade Relationship

Modify the Inter-site Port Cascade Relationship.


Step 4 Click to enter the dynamic configuration interface.

Step 5 Click to implement the dynamic configuration of add slavechain to Site.

----End


77/95







list Table name

1 [Radio Channel Configuration table]

2 [BSC BIE Description table]

3 [Site BIE Trunk Mode Description table]



6 [BSC BIE Active-standby Group Table]

7 [Trunk Circuit Table]

8 [BIE Port Connection Table]

3.14 Deleting Slave Chain of Site

FunctionThis function is used to delete slave chain of site.

Preparation None.

Procedure

Step 1 Select the [BTS/ Delete Slave Chain of Site], and the interface will pop up as shown in Figure3-84 .


78/95





Figure 3-84 Select BIE Board (Delete Slave Chain of Site)


Only the BIE board which has been configur

Documents

HUAWEI BTS312 Dynamic Configuration (BTS)