Grinding wood waste prior to Pellet Milling. Primary and Secondary size reduction

Grinding of Whole Grains or Grasses for Ethanol and other Biofuel production.

Feed and Industrial processing, Pet or Fish Food regrind, Corn Cob Grinding and more.

Hammer Mills

Andritz Feed & Biofuel336 West Penn Street, Muncy PA 17756-1202, USAPhone: 800/446-8629 FAX: 570/546-1615 www.andritz.com

ANDRITZ Hammer Mills Dependable, Effi cient and Flexible

Double-WideHammer Mill

The Double-Wide models with DUAL GRINDING CHAMBER feature two 24” wide or two 30” wide segmented screens.

The Dual MotorAdvantage

The smaller and standard mo-tors are readily available and Economical. Dual Motors also reduce in-rush current during start-up.

Cradle Screen Retainers hold screens tightly in position against the Hammermill casing to eliminate leakage. Opens smoothly for fast and easy screen changes.

LOW PROFILE DOORS reduce space requirements.

Doors are mounted on cam rollers for easy access and maintenance

Single-WideHammer Mill

The 22” and 38” Single-Wide models have a Solid Rotor Design and chain-type screen retaining system.

► Double-wide units with Dual Grinding Chambers.

► Versatile Design is adapt-able for all applications.

► Optional Double base for Dual Motor configurations.

Andritz Feed & Biofuel336 West Penn Street, Muncy PA 17756-1202, USAPhone: 800/446-8629 FAX: 570/546-1615

Full Cylinder Support

► All grinding chambers have large bearings on each end.

► Full Support Design results in longer machine life and bet-ter reliability.

► Cylinders are reversible

Wear Plates for Extra Life

Abrasion resistant 3/8” Wear Plates protect the inside of the grinding chambers in all prod-uct contact areas and provide extra strength.

Replaceable Wear Plates ex-tend machine life.

A Reversible Inlet Baffl e directs material down one side or the other to maintain even wear.

The inlet accepts a spout or a rotary type feeder - BOTH WITH MAGNETIC PROTEC-TION.

OPTIONS

● Andritz Pocket Feeders spread mate-rial evenly across the full width of the Ham-mer mill.

Pocket Feeders elimin- ate the need for separate rotary or knife valves.

Polyurethane, Cast Iron or Aluminum vane pockets are available.

● Hammer Mill Vibration Switch senses an out-of-balance condition and trig-gers an alarm.

● Computerized Process Control for monitoring all parameters to maximize efficiency.

● Manual Braking System

● Discharge Manifold for air swept connection

● Side Panel Air Discharge

● Vane Feeder for light density materials

● Support Stands

● Vibration Isolation Pads

► Slotted housing allows the Cylinder and Bearings to be removed as a unit.

► Heavy-Duty Main Bearings Rugged, large and long-lasting Pillow-Block Bearings for de-pendable performance.

► Screens may be reversed from side to side or rerolled to expose new sharp edges. Extends Screen Life.

►Quick-Release Door Latch and Limit Switches

www.andritz.com

Hammer Mill Technical Data

22”, 38” and 43” Single Base Models

Model 4348 and 4360

Andritz’s registered Trademark, service marks, word marks, and logos, including Andritz may not be used or reproduced without permission. Any individual, organization or company wishing to use Andritz and trademarks must obtain the right to do so in writing from Andritz.

To discuss your applications, request a quote or need more information contact our Technical Representatives at 1-800-446-8629. Visit andritz.com

MODEL A* B C D E F G H J K L

Weight (lb) Less Motor (Approx.)

HP RangeCFM

Required (in2)

22 INCH DIAMETER WITH 3,600 RPM MOTOR22125 33 1/3 31 67 17 5/16 16 12 7/8 8 13 5/8 24 13 5/8 54 1/8 1,125 25-75 740

22185 33 1/3 31 75 17 5/16 16 15 7/8 8 19 5/8 24 19 5/8 59 1/8 1,265 75-100 1,07022245 33 1/3 31 88 17 5/16 16 18 7/8 8 25 5/8 24 25 5/8 69 1/8 1,400 125-150 1,454

38 INCH DIAMETER WITH 1,200 RPM OR 1,800 RPM MOTOR38125 48 50 71 24 5/16 23 11/16 13 1/8 8 13 5/8 33 1/8 13 5/8 57 7/8 2,300 75-125 1,35038185 48 50 79 24 5/16 23 11/16 16 1/8 8 19 5/8 33 1/8 19 5/8 62 7/8 2,550 125-150 1,95038245 48 50 88 24 5/16 23 11/16 19 1/8 8 25 5/8 33 1/8 25 5/8 68 7/8 2,800 150-200 2,55038305 48 50 103 24 5/16 23 11/16 22 1/8 8 31 5/8 33 1/8 31 5/8 80 7/8 3,188 150-300 3,15038365 48 50 109 24 5/16 23 11/16 26 5/8 8 37 5/8 33 1/8 37 5/8 82 7/8 3,900 200-400 3,750

43 INCH DIAMETER WITH 1,800 RPM MOTOR43125 53 50 79 27 5/16 25 11/16 13 1/8 8 13 5/8 32 1/2 13 5/8 67 7/8 3,046 125-150 1,55043185 53 50 88 27 5/16 25 11/16 16 1/8 8 19 5/8 32 1/2 19 5/8 71 7/8 3,540 150-200 2,24043245 53 50 97 27 5/16 25 11/16 19 1/8 8 25 5/8 32 1/2 25 5/8 77 7/8 4,028 200-300 2,95043305 53 50 109 27 5/16 25 11/16 22 1/8 8 31 5/8 32 1/2 31 5/8 82 7/8 4,600 250-400 3,64043365 53 50 130 27 5/16 25 11/16 26 5/8 8 37 5/8 32 1/2 37 5/8 103 3/8 5,250 300-500 4,425

43 INCH DIAMETER WITH 1,800 RPM MOTOR (DOUBLE CHAMBER / DOUBLE MOTOR)4348

SINGLE 53 50 13’ - 3” 27 5/16 25 11/16 36 3/8 8 36 3/4 32 1/2 63 3/4 10’ 2 1/2” 9,050 300-600 5,900DOUBLE 53 50 18’ - 6” 27 5/16 25 11/16 36 3/8 8 36 3/4 32 1/2 63 3/4 15’ 5 5/8” 9,600 300-700 7,280

4360SINGLE 53 50 13’ - 3” 27 5/16 25 11/16 36 3/8 8 36 3/4 32 1/2 63 3/4 10’ 2 1/2” 11,300 300-600 5,900

DOUBLE 53 50 18’ - 6” 27 5/16 25 11/16 36 3/8 8 36 3/4 32 1/2 63 3/4 15’ 5 5/8” 12,010 300-700 7,280

* Contact Andritz for information regarding Inlet Spouts and Pocket Feeders. Subject to change without notice. Dimensions are approximate; for installation request certifi ed drawings.