Upload
others
View
11
Download
0
Embed Size (px)
Citation preview
FPC Connector1.25mm Pitch B Product Specification Issued Date
2013-11-19
Document No:TWVM-RD010 Product Name: WTB CONN.1 of 5
Prepared By: G.X
Rechecked By:G.X
Approved By:LIUPENG
Update List:Item Update Description Rev. Issued Date Revisor1 New Edit A 2011/06/06 G.X2 Update the product code B 2013/11/19 G.X
FPC Connector1.25mm Pitch B Product Specification Issued Date
2013-11-19
Document No:TWVM-RD010 Product Name: WTB CONN.2 of 5
1. SCOPE1.1 Contents
This specification covers the performance, tests and quality requirements for the 1.25P WTB R/A SMTType Connector.
1.2 QualificationWhen tests are performed on the subject product line, the procedures specified in VM inspection plan andproduct drawings.
2. ORDERING INFORMATIONPART NO.:WTB 12 34 xx RX TA x x x
1 2 3 4 5 6 7 8 9
1 Series name WTB Connector
2 Pitch between contacts 12=1.25mmPitch
3 Height of product 34=3.4mm
4 Number of terminals 02~30
5 Assembly style Right angle contact type
6 Packaging TA=Tape reel
7 Plating type 0=Tin G=Gold flash 1=Au:1u’” 5=Au:5u’’
8 Environment number H=HF;G=GP;R=ROHS
9 Other
3. CONNECTOR DIMENSIONSSee attached drawings.
4. MATERIAL
Housing : LCPColor : White
Flammability Rating (UL94V-0)
Terminal: Brass
Peg: Brass
Terminal Plating: See Ordering Information
Peg Plating: Tin over Nickel
5. ACCOMMODATED P.C.B. LAYOUTSee attached drawings.
FPC Connector1.25mm Pitch B Product Specification Issued Date
2013-11-19
Document No:TWVM-RD010 Product Name: WTB CONN.3 of 5
6.RATING.
ITEM STANDARD
Operating Voltage (Max.) 125V AC/DC
Current Rating (Max.) 1.0A AC/DC
Operating Temperature -25°C ~ +85°C (Including terminal temperature rise)
7. PERFORMANCE
ITEM TEST CONDITION REQUIRMENT
Examination of Product Visual inspection.NO physical damage.Meets requirements of productdrawing .
ELECTRICAL PERFORMANCE
Contact Resistance
Mate applicable W.T.B and measure by dry
circuit, 20mV Max, 10mA.
(JIS C5402 5.4)30 mΩ Max.
Insulation Resistance
Measure by applying test potential between theadjacent contacts ,and between the contacts andground in the method 302,(500 V DC±10%).
100 MΩ Min.
Dielectric Strength
Measure by applying test potential between theadjacent contacts ,Current Voltage:250V/AC rms.for 1 minute. MIL-STD-202, Method301.
No evidence of break-down andflashover
MECHANICAL PERFORMANCE
Terminal/Housing retention forceApply axial pull out force at the speed rate of 2±3mm/Min.on the terminal assembled in the housing
0.5kgf(5.0N)Min
Insertion Force & RetentionForce
Pull out force at a speed of 25±3mm perminute Refer to paragrah
FPC Connector1.25mm Pitch B Product Specification Issued Date
2013-11-19
Document No:TWVM-RD010 Product Name: WTB CONN.4 of 5
ITEM TEST CONDITION REQUIRMENT
ENVIRONMENTAL PERFORMANCE AND OTHERS
Temperature Rise
Measure the temperature rise of contact when the
maximum AC
rated current is passed. (UL498)
Temperature
rise30°C Max.
Life testWhen mated up to 30cycles repeatedly (the rate is 10cycles per minute).
Contact
Resistance40 mΩ Max.
Vibration
Mate connectors and subject to the following
vibration conditions, for period of 2 hours in each of
3 mutually perpendicular axes, passing DC 1mA
during the test. Amplitude : 1.5mm P-P
Frequency : 10~55~10 Hz in 1 minute.
Duration : 2 hours in each of X,Y,Z axes.
(MIL-STD-202 Method 201)
Appearance No Damage
Contact
Resistance40 mΩ Max.
Discontinuity 1 μ sec Max.
Shock
Subject to the following shock conditions. 3 times of
shocks shall be applied for each 6 directions along
3 mutually perpendicular axes, passing DC 1 mA
current during the test. (Total of 18 shocks)
Peak value : 490m/s2 50G
(JIS C0041 / MIL-STD-202 Method 213)
Appearance No Damage
Contact
Resistance 40 mΩ Max.
Discontinuity 1 μ sec Max.
Heat Resistance
Expose to 85±2°C for 96 hours. Upon completion of
the exposure period, the test specimens shall be
conditioned at ambient room conditions for 1 to 2
hours, after which the specified measurements
shall be performed. (JIS C0021 / MIL-STD-202
Method108)
Appearance No Damage
Contact
Resistance40 mΩ Max.
Cold Resistance
Expose to -40±2°C for 96 hours.Upon completion ofthe exposure period, the test specimens shall beconditioned at ambient room conditions for 1 to 2hours, after which the specified measurements shallbe performed.(JIS C0020)
Appearance No Damage
ContactResistance
40 mΩ Max.
FPC Connector1.25mm Pitch B Product Specification Issued Date
2013-11-19
Document No:TWVM-RD010 Product Name: WTB CONN.5 of 5
ITEM TEST CONDITION REQUIRMENT
Humidity
Expose to 40 ± 2°C, relative humidity 90 to 95% for96 hours.Upon completion of the exposure period, the testspecimens shall be conditioned at ambient roomconditions for 1 to 2 hours, after which the specifiedmeasurements shall be performed.(JIS C0022 / MIL-STD-202 Method 103)
Appearance No Damage
ContactResistance
40 mΩ Max.
DielectricStrength
No Breakdown
InsulationResistance
50 MΩ Min.
Temperature Cycling
Subject to the following conditions for 5 cycles.Upon completionof the exposure period, the test specimens shall beconditioned at ambient room conditions for 1 to 2hours, after which the specified measurements shalbe performed.1 cycle a) -55±3°C 30minutes
b)+85±3°C 30minutes(Transit time shall be with in 3 minutes)(JIS C0025)
Appearance No Damage
ContactResistance 40 mΩ Max.
Salt Spray
Expose to the following salt mist conditions. Uponcompletion ofthe exposure period, salt deposits shall be removedby a gentle wash or dip in running water, afterwhich the specified measurements shall beperformed.NaCl solutionConcentration : 5 ± 1%Spray time : 48 ± 4 hoursAmbient temperature : 35 ± 2°C(JIS C0023 / MIL-STD-202 Method 101)
Appearance No Damage
ContactResistance
40 mΩ Max.
Solder abilitySolder Temperature: 245 ±5°CImmersion Period: 5±0.5sec
The test area shall be coveredmore than 95% of immersedarea with fresh solder.
Resistance toSoldering Heat
When reflowing…Refer to paragraph 8.Soldering iron method
Soldering time : 3 ±0.5seconds Max.Solder temperature : 380±5°C
Appearance No Damage
FPC Connector1.25mm Pitch B Product Specification Issued Date
2013-11-19
Document No:TWVM-RD010 Product Name: WTB CONN.6 of 5
8. INFRARED REFLOW CONDITION
NOTE: Please check the re-flow soldering condition by your own devices beforehand .Because the condition changes by the soldering devices, p.c. boards, and so on.
9. TAPE AND REEL PACKAGE SPECIFICATION9-1.Tape and Reel Dimensions:See attached drawings.9-2.SpecificationNo. ofContacts
At Initial At 30th No.ofContacts
At Initial At 30th
I.F.(MAX.) R.F.(MIN.) R.F.(MIN.) I.F.(MAX.) R.F.(MIN.) R.F.(MIN.)
02 2.00 0.28 0.18 11 6.50 0.62 0.52
03 2.50 0.30 0.20 12 7.00 0.65 0.55
04 3.00 0.33 0.23 13 7.50 0.68 0.58
05 3.50 0.38 0.28 14 8.00 0.71 0.61
06 4.00 0.43 0.33 15 8.50 0.74 0.64
08 5.00 0.53 0.43 20 11.00 0.89 0.79
09 5.50 0.56 0.46 25 13.50 1.04 0.94
10 6.00 0.59 0.49 30 16.00 1.19 1.09
10. TAPE AND REEL PACKAGE SPECIFICATION10-1. Tape and Reel Dimensiongs : See attached drawings.10.-2 Specification
No.of Terminals Width ?Pcs/Reel ?Reels/Carton
02~09 16 2000/1 12/1
10~14 24 2000/1 10/1
15 32 2000/1 8/1
Export Carton Layer : 3 Layers Carton Size : 350×350×34mm
0
50
100
150
200
230
250°C MAX.(Peak Temp.)3Sec. or less
230°C MIN. / 20~40Sec.°C
Start
60 Sec. 60~90 Sec. 30 Sec.
Time(sec.)