Foreword - Just Give Me The Damn Manual...02MY CELICA U (L/O 0108) iv 2002 MY CELICA_U (OM20792U) Spark ignition system of your Toyota The spark ignition system in your Toyota meets

’02MY CELICA U (L/O 0108)

i2002 MY CELICA_U (OM20792U)

Foreword

Welcome to the growing group of value−conscious people who drive Toyotas. We are proud of the advanced engineering andquality construction of each vehicle we build.

This Owner’s Manual explains the operation of your new Toyota. Please read it thoroughly and have all the occupantsfollow the instructions carefully. Doing so will help you enjoy many years of safe and trouble−free motoring. Forimportant information about this manual and your Toyota, read the following pages carefully.

When it comes to service, remember that your Toyota dealer knows your vehicle best and is interested in your completesatisfaction. He will provide quality maintenance and any other assistance you may require.

If there is not a Toyota dealer near you, or you need emergency assistance for any reason, please call the following number:

� U.S. OWNERS: Toyota Customer Assistance Center Toll−free:1−800−331−4331

� CANADIAN OWNERS: Toyota Canada Customer Interaction Centre Toll−free:1−888−TOYOTA−8 (1−888−869−6828)

Please leave this Owner’s Manual in this vehicle at the time of resale. The next owner will need this information also.

All information and specifications in this manual are current at the time of printing. However, because of Toyota’s policy ofcontinual product improvement, we reserve the right to make changes at any time without notice.

Please note that this manual applies to all models and explains all equipment, including options. Therefore, you mayfind some explanations for equipment not installed on your vehicle.

© 2001 TOYOTA MOTOR CORPORATION

All rights reserved. This material may not be reproduced or copied, in whole or in part, without the written permission of ToyotaMotor Corporation.


ii 2002 MY CELICA_U (OM20792U)

Important information about this manual

Safety and vehicle damage warnings

Throughout this manual, you will see safety and vehicle dam-age warnings. You must follow these warnings carefully toavoid possible injury or damage.

The types of warnings, what they look like, and how they areused in this manual are explained as follows:

CAUTION

This is a warning against something which may causeinjury to people if the warning is ignored. You areinformed about what you must or must not do inorder to avoid or reduce the risk to yourself and otherpeople.

NOTICE

This is a warning against something which may causedamage to the vehicle or its equipment if the warningis ignored. You are informed about what you must ormust not do in order to avoid or reduce the risk ofdamage to your vehicle and its equipment.

Safety symbol

When you see the safety symbolshown above, it means: “Do not...”;“Do not do this”; or “Do not let thishappen”.


iii 2002 MY CELICA_U (OM20792U)

Important information about your Toyota

New vehicle warranty

Your new vehicle is covered by the following Toyota limitedwarranties:

� New vehicle warranty

� Emission control systems warranty

� Others

For further information, please refer to the “Owner’sWarranty Information Booklet” or “Owner’s ManualSupplement”.

Your responsibility formaintenance

It is owner’s responsibility to make sure that the specifiedmaintenance is performed. Section 6 gives details of thesemaintenance requirements. Also included in Section 6 isgeneral maintenance. For scheduled maintenance informa-tion, please refer to the “Scheduled Maintenance Guide” or“Owner’s Manual Supplement”.

Accessories, spare parts andmodification of your Toyota

A wide variety of non−genuine spare parts and accessoriesfor Toyota vehicles are currently available in the market.You should know that Toyota does not warrant these prod-ucts and is not responsible either for their performance,repair or replacement, or for any damage they may causeto, or adverse effect they may have on, your Toyota ve-hicle.

This vehicle should not be modified with non−genuineToyota products. Modification with non−genuine Toyotaproducts could affect its performance, safety or durability,and may even violate governmental regulations. In addi-tion, damage or performance problems resulting from themodification may not be covered under warranty.


iv 2002 MY CELICA_U (OM20792U)

Spark ignition system of yourToyota

The spark ignition system in your Toyota meets all require-ments of the Canadian Interference−Causing EquipmentStandard.

Installation of a mobiletwo−way radio system

As the installation of a mobile two−way radio system inyour vehicle could affect electronic systems such as multi-port fuel injection system/sequential multiport fuel injectionsystem, cruise control system, anti−lock brake system,SRS airbag system and seat belt pretensioner system, besure to check with your Toyota dealer for precautionarymeasures or special instructions regarding installation.

Scrapping of your Toyota

The SRS airbag and seat belt pretensioner devices in yourToyota contain explosive chemicals. If the vehicle isscrapped with the airbags and pretensioners left as theyare, this may cause an accident such as fire. Be sure tohave the systems of the SRS airbag and seat belt preten-sioner removed and disposed of by a qualified serviceshop or by your Toyota dealer before you dispose of yourvehicle.


12002 MY CELICA_U (OM20792U)

OPERATION OF INSTRUMENTS ANDCONTROLSOverview of instruments and controls

Instrument panel overview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument cluster overview 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Indicator symbols on the instrument panel 5. . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 1


2 2002 MY CELICA_U (OM20792U)

1. Side vents

2. Instrument cluster

3. Center vents

4. Electric moon roof switch and/orinterior light

5. Glove box

6. Manual transmission gear shift lever orautomatic transmission selector lever

7. Power window switches

8. Power door lock switch

9. Auxiliary box

10. Parking brake lever

11. Hood lock release lever

12. Power rear view mirror control switches

Instrument panel overview



1. Instrument panel light control knob

2. Headlight and turn signal switch, andfront fog light switch

3. Wiper and washer switches

4. Transmission shift switches

5. Emergency flasher switch

6. Clock

7. Auxiliary box

8. Car audio

9. Air conditioning controls

10. Rear window defogger switch

11. Cigarette lighter

12. Ashtray

13. Ignition switch

14. Cruise control switch

15. Tilt steering lock release lever

16. Window lock switch



1. Tachometer

2. Service reminder indicators andindicator lights

3. Speedometer

4. Fuel gauge

5. Engine coolant temperature gauge

6. Odometer and two trip meters

7. Trip meter reset knob

8. Gear position indicators

Instrument cluster overview



SRS warning light∗1

Open door warning light∗1

Brake system warning light∗1

Discharge warning light∗1

Low engine oil pressure warning light∗1

Malfunction indicator lamp∗1

Anti−lock brake system warning light∗1

Driver’s seat belt reminder light∗1

Low fuel level warning light∗1

or or

Automatic transmission fluid temperature warninglight∗1

Headlight low beam indicator light

Tail light indicator light

Headlight high beam indicator light

Front passenger’s seat belt reminder light∗1

Indicator symbols on the instrument panel



∗1: For details, see “Service reminder indicators and warningbuzzers” in Section 1−5.

∗2: If this light flashes, see “Automatic transmission” in Section1−6.

∗3: If this light flashes, see “Cruise control” in Section 1−6.

Cruise control indicator light∗3

Overdrive−off indicator light

Automatic transmission indicator lights

M mode indicator light∗2

Turn signal indicator lights



OPERATION OF INSTRUMENTS ANDCONTROLSKeys and Doors

Keys 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Side doors 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Power windows 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Back door 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hood 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel tank cap 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electric moon roof 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 2



Your vehicle is supplied with two kindsof keys.

1. Master key—This key works in everylock.

2. Sub key—This key will not work in theback door and glove box.

To protect things locked in the glove boxor luggage compartment when you haveyour vehicle parked, leave the sub keywith the attendant.

Since the side doors and back door canbe locked without a key, you should al-ways carry a spare master key in caseyou accidentally lock your keys inside thevehicle.

KEY NUMBER PLATE

Your key number is shown on the plate.Keep the plate in a safe place such asyour wallet, not in the vehicle.

If you should lose your keys or if youneed additional keys, duplicates can bemade by a Toyota dealer using the keynumber.

We recommend to write down the keynumber and keep it in safe place.

LOCKING AND UNLOCKING WITH KEY

Insert the key into the keyhole and turnit.

To lock: Turn the key forward. To unlock: Turn the key backward.

Vehicles with a power door lock system—Both side doors and back door lock andunlock simultaneously with either sidedoor. In the driver’s door lock, turning thekey once will unlock the driver’s door andtwice in succession will unlock both sidedoors and back door simultaneously.

Keys Side doors—



Vehicles with a power door lock system—When both side doors and back door areunlocked simultaneously with a key, theinterior light comes on for about 15 sec-onds and then fades out, even if the dooris not opened. (For further information,see “Interior light” in Section 1−4.)

LOCKING AND UNLOCKING WITHINSIDE LOCK KNOB

Move the lock knob.

To lock: Push the knob forward.To unlock: Pull the knob backward.

Closing the side door with the lock knobin the lock position will also lock the sidedoor. Be careful not to lock your keys inthe vehicle.

Vehicles with a power door lock sys-tem—The side doors cannot be locked ifyou leave the key in the ignition switch.

LOCKING AND UNLOCKING WITHPOWER DOOR LOCK SWITCH

Push the switch.

To lock: Push the switch on the front side.To unlock: Push the switch on the rearside.

Both side doors and back door lock orunlock simultaneously.



CAUTION

Before driving, be sure that the sidedoors are closed and locked, espe-cially when small children are in thevehicle. Along with the proper use ofseat belts, locking the side doorshelps prevent the driver and passen-gers from being thrown out from thevehicle during an accident. It alsohelps prevent the side doors from be-ing opened unintentionally.

Locking operation

Unlocking operation

The wireless remote control system isdesigned to lock or unlock both sidedoors and back door, or activate the“PANIC” mode from a distance withinapproximately 1 m (3 ft.) of the vehicle.

LOCKING AND UNLOCKING THE SIDEDOORS AND BACK DOOR

To lock and unlock both side doors andback door, push the switches of thetransmitter slowly and securely.

To lock: Push the “LOCK” switch. Bothside doors and back door are locked si-multaneously. At this time, parking lights,side marker lights and tail lights flash.

Check to see that both side doors andback door are securely locked.

If either side doors or back door is notsecurely closed, or if the key is in theignition switch, locking cannot be per-formed by the “LOCK” switch.

To unlock: Push the “UNLOCK” switchonce to unlock the driver’s door alone.Pushing the switch twice within 3 secondsunlocks both side doors and back doorsimultaneously. At this time, parking lights,side marker lights and tail lights flashtwice.

—Wireless remote control



When both side doors and back door areunlocked simultaneously with a wirelessremote control transmitter, the interior lightcomes on for about 15 seconds and thenfades out, even if the door is not opened.(For further information, see “Interior light”in Section 1−4.)

You have 30 seconds to open a door afterusing the wireless remote unlock feature.If a door is not opened by then, both sidedoors and back door will be automaticallylocked again.

If the “LOCK” or “UNLOCK” switch is keptpressed in, the locking or unlocking opera-tion is not repeated. Release the buttonand then push again.

“PANIC” SWITCH

Pushing the “PANIC” switch blows thehorn intermittently and flashes theheadlights and tail lights.

The “PANIC” switch is used to deter ve-hicle theft when you witness anyone at-tempting to break into or damage yourvehicle.

The alarm will last for one minute. To stopalarm midway, do the following:

� Push the “PANIC” switch once again.

� Unlock either side door or back doorwith the key or wireless remote controltransmitter.

� Turn the ignition key from the “LOCK”to “ACC” or “ON” position.

The “PANIC” mode does not work whenthe ignition key is in the “ACC” or “ON”position.

WIRELESS REMOTE CONTROLTRANSMITTER

The wireless remote control transmitter isan electronic component. Observe the fol-lowing instructions in order not to causedamage to the transmitter.

� Do not leave the transmitter on placeswhere the temperature becomes highsuch as on the dashboard.

� Do not disassemble it.

� Avoid knocking it hard against otherobjects or dropping it.

� Avoid putting it in water.

You can use up to 4 wireless remote con-trol transmitters for the same vehicle.Contact your Toyota dealer for detailedinformation.

If the wireless remote control transmitterdoes not actuate the doors or alarm, oroperate from a normal distance:

� Check for closeness to a radio trans-mitter such as a radio station or anairport which can interfere with normaloperation of the transmitter.



� The battery may have been consumed.Check the battery in the transmitter. Toreplace the battery, see “REPLACINGTRANSMITTER BATTERY”.

If you lose your transmitter, contact yourToyota dealer as soon as possible toavoid the possibility of theft, or an acci-dent.

If you lose your transmitter, contact yourToyota dealer as soon as possible toavoid the possibility of theft, or an acci-dent. (See “If you lose your wireless re-mote control transmitter” in Section 4.)

For vehicles sold in U.S.A.

This device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions:

(1) This device may not cause harmfulinterference, and (2) this device mustaccept any interference received, includ-ing interference that may cause unde-sired operation.

NOTICE:This equipment has been tested andfound to comply with the limits for aClass B digital device, pursuant to Part15 of the FCC Rules. These limits aredesigned to provide reasonable protec-tion against harmful interference in aresidential installation. This equipmentgenerates, uses and can radiate radiofrequency energy and, if not installedand used in accordance with the instruc-tions, may cause harmful interference toradio communications. However, thereis no guarantee that interference will notoccur in a particular installation. If thisequipment does cause harmful interfer-ence to radio or television reception,which can be determined by turning theequipment off and on, the user is en-couraged to try to correct the interfer-ence by one or more of the followingmeasures:

� Reorient or relocate the receiving an-tenna.

� Increase the separation between theequipment and receiver.

� Connect the equipment into an outleton a circuit different from that towhich the receiver is connected.

� Consult the dealer or an experiencedradio/TV technician for help.

FCC WARNING:Changes or modifications not ex-pressly approved by the party respon-sible for compliance could void theuser’s authority to operate the equip-ment.

For vehicles sold in Canada

Operation is subject to the following twoconditions:

(1) this device may not cause interfer-ence, and (2) this device must acceptany interference, including interferencethat may cause undesired operation ofthe device.



REPLACING TRANSMITTER BATTERY

For replacement, use a CR2016 lithiumbattery or equivalent.

CAUTION

Special care should be taken thatsmall children do not swallow the re-moved transmitter battery or compo-nents.

NOTICE

� During replacing the transmitterbattery, do not push the “LOCK”and “UNLOCK” switches manytimes.

� When replacing the transmitter bat-tery, be careful not to lose the com-ponents.

� Replace only with the same orequivalent type recommended bythe manufacturer.

� Dispose of used batteries accordingto the local laws.

Replace the transmitter battery by the fol-lowing procedures:

1. Using a coin or equivalent, open thetransmitter case.

2. Remove the discharged transmitter bat-tery.

NOTICE

Do not bend the terminals.



3. Put a new transmitter battery with posi-tive (+) side up.

Close the transmitter case securely.

NOTICE

� Make sure the positive side andnegative side of the transmitter bat-tery should be faced correctly.

� Do not replace the battery with wethands. Water may cause unexpectedrust.

� Do not touch or move any compo-nents inside of the transmitter, orit may interfere with proper opera-tion.

� Be careful not to bend the electrodeof the transmitter battery insertionand that dust or oils do not adhereto the transmitter case.

� Close the transmitter case securely.

After replacing battery, check that thetransmitter operates properly. If the trans-mitter still does not operate properly, con-tact your Toyota dealer.

The windows can be operated with theswitch on the center console.

The power windows work when the ignitionswitch is in the “ON” position.

Key off operation: If both side doors areclosed, they work for 43 seconds evenafter the ignition switch is turned off. Theystop working when either side door isopened.

OPERATING THE DRIVER’S WINDOW

Use the switch on the driver’s side ofthe center console.

Normal operation: The window moves aslong as you hold the switch.

To open: Lightly push down the switch.To close: Pull up the switch.

Power windows



Automatic operation (to open only):Push the switch completely down and thenrelease it. The window will fully open. Tostop the window partway, lightly pull theswitch up and then release it.

OPERATING THE PASSENGER’SWINDOW

Use the switch on the passenger’s sideof the center console.

The window moves as long as you holdthe switch.

To open: Push down the switch.To close: Pull up the switch.

If you push in the window lock switch onthe instrument panel, the passenger’s win-dow cannot be operated.



CAUTION

To avoid serious personal injury, youmust do the following.

� Always make sure the heads, handsand other parts of the bodies of alloccupants are kept completely in-side the vehicle before you closethe power windows. If someone’sneck, head or hands gets caught ina closing window, it could result ina serious injury. When anyonecloses the power windows, makesure that he/she operates the win-dows safely.

� When small children are in the ve-hicle, never let them use the powerwindow switches without supervi-sion. Use the window lock switch toprevent them from making unex-pected use of the switches.

� Never leave small children alone inthe vehicle, especially with the igni-tion key still inserted. They coulduse the power window switches andget trapped in a window. Unat-tended children can be involved inserious accidents.

Insert the master key into the keyholeand turn it.

To lock: Turn the key clockwise.To unlock: Turn the key counterclockwise.

To open the back door, pull the lock re-lease lever.

Operating the power door lock switch orwireless remote control transmitter simul-taneously locks or unlocks the back door.(See “Side doors” in this section.)

When closing the back door, make sureit is securely closed.

See “Luggage stowage precautions” inSection 2 for precautions in loading lug-gage.

When closing the back door, use theinside handle for easier reach to theback door.

To close the back door, lower it and pressdown on it. After closing the back door,try pulling it up to make sure it is secure-ly closed.

CAUTION

Keep the back door closed while driv-ing. This not only keeps the luggagefrom being thrown out but also pre-vents exhaust gases from enteringthe vehicle.

Back door



To open the hood:

1. Pull the hood lock release lever. Thehood will spring up slightly.

CAUTION

Before driving, be sure that the hoodis closed and securely locked. Other-wise, the hood may open unexpected-ly while driving and an accident mayoccur.

2. In front of the vehicle, pull up theauxiliary catch lever and lift thehood.

3. Hold the hood open by inserting thesupport rod into the slot.

Before closing the hood, check to see thatyou have not forgotten any tools, rags,etc. and return the support rod to itsclip—this prevents rattles. Then lower thehood and make sure it locks into place.If necessary, press down gently on thefront edge to lock it.

CAUTION

After inserting the support rod intothe slot, make sure the rod supportsthe hood securely from falling downon to your head or body.

Hood



NOTICE

Be sure to return the support rod toits clip before closing the hood. Clos-ing the hood with the support rod upcould cause the hood to bend.

This indicates that the fuel filler dooris on the left side of your vehicle.

1. To open the fuel filler door, pull thelever up.

When refueling, turn off the engine.

CAUTION

� Do not smoke, cause sparks or al-low open flames when refueling.The fumes are flammable.

� When opening the cap, do not re-move the cap quickly. In hot weath-er, fuel under pressure could causeinjury by spraying out of the fillerneck if the cap is suddenly re-moved.

Fuel tank cap



2. To remove the fuel tank cap, turnthe cap slowly counterclockwise,then pause slightly before removingit. After removing the cap, hang thetether as shown in the illustration.

It is not unusual to hear a slight swooshwhen the cap is opened. When installing,turn the cap clockwise till you hear aclick.

If the cap is not tightened securely, themalfunction indicator lamp comes on.Make sure the cap is tightened securely.

The indicator lamp goes off after drivingseveral times. If the indicator lamp doesnot go off, contact your Toyota dealer assoon as possible.

CAUTION

� Make sure the cap is tightened se-curely to prevent fuel spillage incase of an accident.

� Use only a genuine Toyota fuel tankcap for replacement. It has a built−in check valve to reduce fuel tankpressure.

Tilting operation

Sliding operation

Electric moon roof



To operate the moon roof, use theswitch beside the interior light.

The moon roof works when the ignitionswitch is in the “ON” position.

Key off operation: If both side doors areclosed, it works for 43 seconds even afterthe ignition switch is turned off. It stopsworking when either side door is opened.

Tilting operation—

To tilt up: Push the switch briefly on the“OPEN” side. The roof will tilt up com-pletely.

To stop the roof partway, push the switcheither the “OPEN” or “CLOSE” side briefly.

The sun shade will open lightly with themoon roof. To open the sun shade com-pletely, pull it back by hand.

To lower: Push the switch briefly on the“CLOSE” side. The roof will lower com-pletely.

Sliding operation—

To open (with the roof tilting up): Push theswitch on the “OPEN” side briefly. Theroof will open completely.

To open (with the roof tilting down): Pushthe switch on the “OPEN” side for morethan 2 seconds. The roof will open com-pletely after tilting up.

To stop the roof partway, push the switcheither the “OPEN” or “CLOSE” side briefly.

The sun shade will be opened togetherwith the roof.

To close: Push the switch briefly on the“CLOSE” side. The roof will close com-pletely.

Sun shade operation—

The sun shade can be closed by hand.

Jam protection function: During closingoperation, the moon roof stops and openshalf way if something gets caught betweenthe moon roof and frame.

If the moon roof receives a strong impact,this function may work even if nothing iscaught.

When the battery is disconnected, themoon roof cannot operate automaticallyand the jam protection function will notfunction correctly. Therefore, you need tonormalize the moon roof as follows.

To normalize: Close the moon roof, andcontinue to hold the switch up briefly afterthe moon roof reaches the completelyclosed position and the motor is blocked.

If the moon roof cannot be operated prop-erly, have it checked by your Toyota deal-er.

There are cases where malfunctions mayactivate the jam protection function, whichwill prevent the roof from closing com-pletely. In this case, pushing and holdingthe switch on the “CLOSE” side will closethe roof completely.

CAUTION

To avoid serious personal injury, youmust do the following.

� While the vehicle is moving, alwayskeep the heads, hands and otherparts of the bodies of all occupantsaway from the roof opening. Other-wise, they could be seriously in-jured if the vehicle stops suddenlyor if the vehicle is involved in anaccident.

� Always make sure nobody placeshis/her head, hands and other partsof the body in the roof opening be-fore you close the roof. If some-one’s neck, head or hands getscaught in the closing roof, it couldresult in a serious injury. Whenanyone closes the roof, first makesure it is safe to do so.



� Never leave small children alone inthe vehicle, especially with the igni-tion key still inserted. They coulduse the moon roof switches and gettrapped in the roof opening. Unat-tended children can be involved inserious accidents.

� Never sit on top of the vehiclearound the roof opening.

� Never try jamming any part of yourbody to make the jam protectionfunction work intentionally.

� The jam protection function maynot work if something gets caughtjust before the moon roof is fullyclosed.

NOTICE

� There is the possibility that wateror rain will get into the vehicle ifyou operate the moon roof after arainfall, snowfall or car wash. Wipethe moon roof dry with a cloth be-fore operating it.

� Do not touch the plastic resin moonroof with anything hard or sharp.The roof is damaged more easilythan ordinary glass.

� When washing the plastic resinmoon roof, use a mild soap or neu-tral detergent. Do not use wax, win-dow cleaner or abrasive clean-er—these may damage the plasticresin moon roof. (See “Washing andwaxing your Toyota” in Section 5.)

� Do not use organic substances(gasoline, kerosene, benzine orstrong solvents), which may toxicor cause damage.

� Do not use window scraper or deic-er when the plastic resin moon roofis heavily coated with frost or ice.The plastic resin moon roof is easi-ly damaged.





OPERATION OF INSTRUMENTS ANDCONTROLSSeats, Seat belts, Steering wheel and MirrorsSeats 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front seats 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fold−down rear seat 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat belts 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SRS driver airbag and front passenger airbagrbag 34. . . . . . . . . . . . . . . SRS side airbags 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Child restraint 47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tilt steering wheel 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Outside rear view mirrors 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anti−glare inside rear view mirroror 62. . . . . . . . . . . . . . . . . . . . . . . . . . . . Vanity mirrors 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 3



While the vehicle is being driven, all ve-hicle occupants should have the seatbackupright, sit well back in the seat and prop-erly wear the seat belts provided.

CAUTION

� Do not drive the vehicle unless theoccupants are properly seated. Donot allow sitting on top of afolded−down seatback, or in theluggage compartment or cargo area.Persons not properly seated and/orproperly restrained by seat beltscan be severely injured in the eventof emergency braking or a collision.

� During driving, do not allow pas-sengers to stand up or movearound between seats. Severe inju-ries can occur in the event of emer-gency braking or a collision.

CAUTION

The SRS side airbags are installed inthe driver and front passenger seats.Observe the following precautions.

� Do not lean against the front doorwhen the vehicle is in use. The sideairbag inflates with considerablespeed and force; you may be killedor seriously injured.

� Do not use accessories for theseats which cover the parts wherethe side airbags inflate. Such acces-sories may prevent the side airbagsfrom activating correctly, causingdeath or serious injury.

� Do not modify or replace the seatsor upholstery of the front seatswith the side airbags. Such changesmay disable the system or causethe side airbags to inflate acciden-tally, resulting in death or seriousinjury. Consult your Toyota dealer ifyou insist on modifications of thiskind.

Adjust the driver’s seat so that the footpedals, steering wheel and instrumentpanel controls are within easy reach ofthe driver.

CAUTION

� Adjustments should not be madewhile the vehicle is moving, as theseat may unexpectedly move andcause the driver to lose control ofthe vehicle.

� When adjusting the seat, be carefulthat the seat does not hit a passen-ger or luggage.

� After adjusting the seat position,try sliding it forward and backwardto make sure it is locked in posi-tion.

� After adjusting the seatback, pushback your body to make sure it islocked in position.

� Do not put objects under the seats.The objects may interfere with theseat−lock mechanism or unexpect-edly push up the seat position ad-justing lever; the seat may suddenlymove, causing the driver to losecontrol of the vehicle.

Seats

Front seats——Front seat precautions(on vehicles with SRS side airbags) —Seat adjustment precautions



� While adjusting the seat, do not putyour hands under the seat or nearthe moving parts. You may jamyour hands or fingers.

1. SEAT POSITION ADJUSTING LEVER

Hold the center of the lever and pull itup. Then slide the seat to the desiredposition with slight body pressure andrelease the lever.

2. SEATBACK ANGLE ADJUSTINGLEVER

Lean forward and pull the lever up.Then lean back to the desired angleand release the lever.

CAUTION

To reduce the risk of sliding underthe lap belt during a collision, avoidreclining the seatback any more thanneeded. The seat belts provide maxi-mum protection in a frontal or rearcollision when the driver and the pas-senger are sitting up straight andwell back in the seats. If you arereclined, the lap belt may slide pastyour hips and apply restraint forcesdirectly to the abdomen. Therefore, inthe event of a frontal collision, therisk of personal injury may increasewith increasing recline of the seat-back.

—Adjusting front seats



3. SEAT CUSHION ANGLE ADJUSTINGKNOB

Turn the knob either way.

For easy access to the rear seat, dothis.

1. Lift the seatback angle adjusting leveror press the pedal behind the seat-back.

The seat will slide forward.

2. Move the seat to the front−most posi-tion.

After passengers are in, lift up the seat-back and return the seat until it locks.

CAUTION

� After putting back the seat, trypushing the seat forward and rear-ward to make sure it is secured inplace.

� Never allow anyone to rest theirfoot on the release pedal while thevehicle is moving.

—Moving passenger’s seat forrear seat entry



1. Make sure the shoulder belt passesthrough the hanger when folding therear seat.

This prevents the shoulder belt from beingdamaged.

CAUTION

The seat belt must be removed fromthe hanger when the seat belt is inuse.

2. Pull the lock release button and folddown the seatback.

Each seatback may be folded separately.

This will enlarge the luggage compartmentas far as the front seatbacks. See “Lug-gage stowage precautions” in Section 2for precautions in loading luggage.

CAUTION

When returning the seatback to theupright position, observe the follow-ing precautions in order to preventpersonal injury in a collision or sud-den stop:

� Make sure the seatback is securelylocked by pushing forward and rear-ward on the top of the seatbackand that the red mark at the buttonon the top of the seatback cannotbe seen. Failure to do so will pre-vent the seat belt from operatingproperly.

� Make sure the seat belts are nottwisted or caught in the seatbackand are arranged in their properposition and are ready to use.

Fold−down rear seat



Toyota strongly urges that the driver andpassengers in the vehicle be properly re-strained at all times with the seat beltsprovided. Failure to do so could increasethe chance of injury and/or the severity ofinjury in accidents.

Child. Use a child restraint system ap-propriate for the child until the child be-comes large enough to properly wear thevehicle’s seat belts. See “Child restraint”for details.

If a child is too large for a child restraintsystem, the child should sit in the rearseat and must be restrained using thevehicle’s seat belt. According to accidentstatistics, the child is safer when properlyrestrained in the rear seat than in thefront seat.

If a child must sit in the front seat, theseat belts should be worn properly. If anaccident occurs and the seat belts are notworn properly, the force of the rapid infla-tion of the airbag may cause death orserious injury to the child.

Do not allow the child to stand up orkneel on either rear or front seats. Anunrestrained child could suffer serious in-jury or death during emergency braking ora collision. Also, do not let the child siton your lap. It does not provide sufficientrestraint.

Pregnant woman. Toyota recommends theuse of a seat belt. Ask your doctor forspecific recommendations. The lap beltshould be worn securely and as low aspossible over the hips and not on thewaist.

Injured person. Toyota recommends theuse of a seat belt. Depending on the inju-ry, first check with your doctor for specificrecommendations.

CAUTION

Persons should ride in their seatsproperly wearing their seat beltswhenever the vehicle is moving.Otherwise, they are much more likelyto suffer serious bodily injury ordeath in the event of sudden brakingor a collision.

When using the seat belts, observethe following:

� Use the belt for only one person ata time. Do not use a single belt fortwo or more people—even children.

� Avoid reclining the seatbacks toomuch. The seat belts provide maxi-mum protection when the seatbacksare in the upright position. (Referto the seat adjustment instructions.)

� Be careful not to damage the beltwebbing or hardware. Take care thatthey do not get caught or pinchedin the seat or side doors.

� Inspect the belt system periodically.Check for cuts, fraying, and looseparts. Damaged parts should be re-placed. Do not disassemble ormodify the system.

� Keep the belts clean and dry. Ifthey need cleaning, use a mild soapsolution or lukewarm water. Neveruse bleach, dye, or abrasive clean-ers—they may severely weaken thebelts. (See “Cleaning the interior”in Section 5.)

� Replace the belt assembly (includ-ing bolts) if it has been used in asevere impact. The entire assemblyshould be replaced even if damageis not obvious.

Seat belts——Seat belt precautions



Adjust the seat as needed (front seatsonly) and sit up straight and well backin the seat. To fasten your belt, pull itout of the retractor and insert the tabinto the buckle.

You will hear a click when the tab locksinto the buckle.

The seat belt length automatically adjuststo your size and the seat position.

The retractor will lock the belt during asudden stop or on impact. It also maylock if you lean forward too quickly. Aslow, easy motion will allow the belt toextend, and you can move around freely.

If the seat belt cannot be pulled out of theretractor, firmly pull the belt and releaseit. You will then be able to smoothly pullthe belt out of the retractor.

When a passenger’s shoulder belt is com-pletely extended and is then retractedeven slightly, the belt is locked in thatposition and cannot be extended. This fea-ture is used to hold the child restraintsystem securely. (For details, see “Childrestraint” in this section.) To free the beltagain, fully retract the belt and then pullthe belt out once more.

CAUTION

� After inserting the tab, make surethe tab and buckle are locked andthat the belt is not twisted.

� Do not insert coins, clips, etc. inthe buckle as this may prevent youfrom properly latching the tab andbuckle.

� If the seat belt does not functionnormally, immediately contact yourToyota dealer. Do not use the seatuntil the seat belt is fixed. It cannotprotect an adult occupant or yourchild from injury.

Take upslack

Too high

Keep as low onhips as possible

Adjust the position of the lap andshoulder belts.

Position the lap belt as low as possibleon your hips—not on your waist, then ad-just it to a snug fit by pulling the shoulderportion upward through the latch plate.

—Seat belts



CAUTION

� Both high−positioned lap belts andloose−fitting belts could cause seri-ous injuries due to sliding underthe lap belt during a collision orother unintended result. Keep thelap belt positioned as low on hipsas possible.

� For your safety, do not place theshoulder belt under your arm.

To release the belt, press the buckle−re-lease button and allow the belt to re-tract.

If the belt does not retract smoothly, pullit out and check for kinks or twists. Thenmake sure it remains untwisted as it re-tracts.

The seat belt can be stowed in thetongue holder when it is not in use.

CAUTION

The seat belt must be removed fromthe tongue holder when the seat beltis in use.

—Stowing the frontpassenger’s seat belt



If your seat belt cannot be fastened se-curely because it is not long enough, apersonalized seat belt extender is avail-able from your Toyota dealer free ofcharge.

Please contact your local Toyota dealer sothat the dealer can order the proper re-quired length for the extender. Bring theheaviest coat you expect to wear for prop-er measurement and selection of length.Additional ordering information is availableat your Toyota dealer.

CAUTION

When using the seat belt extender,observe the following precautions.Failure to follow these instructionscould result in less effectiveness ofthe seat belt restraint system in caseof vehicle accident, increasing thechance of personal injury.

� Never use the seat belt extender ifyou can fasten the seat belt withoutit.

� Remember that the extender pro-vided for you may not be safe whenused on a different vehicle, or foranother person or at a differentseating position than the one origi-nally intended for.

To connect the extender to the seatbelt, insert the tab into the seat beltbuckle so that the “PRESS” signs onthe buckle−release buttons of the ex-tender and the seat belt are both facingoutward as shown.

You will hear a click when the tab locksinto the buckle.

When releasing the seat belt, press onthe buckle−release button on the extender,not on the seat belt. This helps preventdamage to the vehicle interior and extend-er itself.

When not in use, remove the extenderand store in the vehicle for future use.

—Seat belt extender



CAUTION

� After inserting the tab, make surethe tab and buckle are locked andthat the seat belt extender is nottwisted.


� If the seat belt does not functionnormally, immediately contact yourToyota dealer. Do not use the seatuntil the seat belt is fixed. It cannotprotect an adult occupant or yourchild from injury.

The driver and front passenger’s seatbelt pretensioners are designed to beactivated in response to a severe fron-tal impact.

When the airbag sensor detects the shockof a severe frontal impact, the front seatbelts are quickly drawn back in by theretractors so that the belts snugly restrainthe front seat occupants.

The front seat belt pretensioners are acti-vated even with no passenger in the frontseat.

Collisions occurring at certain speeds andangles may cause the front seat belt pre-tensioners and SRS airbags not to operateall together.

This indicator comes on when the igni-tion key is turned to the “ON” position.It goes off after about 6 seconds. Thismeans the front seat belt pretensionersare operating properly.

This warning light system monitors theairbag sensor assembly, front airbag sen-sors, side airbag sensors, door side air-bag sensors, front seat belt pretensionerassemblies, inflators, warning light, inter-connecting wiring and power sources. (Fordetails, see “Service reminder indicatorsand warning buzzers” in Section 1−5.)

—Front seat beltpretensioners



The front seat belt pretensioner systemmainly consists of the following compo-nents and their locations are shown in theillustration.

1. Front airbag sensors

2. SRS warning light

3. Front seat belt pretensioner assemblies

4. Airbag sensor assembly

The front seat belt pretensioners are con-trolled by the airbag sensor assembly. Theairbag sensor assembly consists of a saf-ing sensor and airbag sensor.

When the front seat belt pretensioners areactivated, an operating noise may beheard and a small amount of smoke−likegas may be released. This gas is harm-less and does not indicate that a fire isoccurring.

Once the front seat belt pretensionershave been activated, the seat belt retrac-tors remain locked.

CAUTION

Do not modify, remove, strike or openthe front seat belt pretensioner as-semblies, airbag sensor or surround-ing area or wiring. Doing any ofthese may cause sudden operation ofthe front seat belt pretensioners ordisable the system, which could re-sult in death or serious injury.

Failure to follow these instructionscan result in death or serious inju-ries.

NOTICE

Do not perform any of the followingchanges without consulting yourToyota dealer. Such changes caninterfere with proper operation of thefront seat belt pretensioners in somecases.

� Installation of electronic devicessuch as a mobile two−way radio,cassette tape player or compactdisc player

� Repairs on or near the front seatbelt retractor assemblies

� Modification of the suspension sys-tem

� Modification of the front end struc-ture

� Attachment of a grille guard (bullbar, kangaroo bar, etc.), snowplow,winches or any other equipment tothe front end

� Repairs made on or near the frontfenders, front end structure or con-sole



This front seat belt pretensioner systemhas a service reminder indicator to informthe driver of operating problems. If any ofthe following conditions occurs, thisindicates a malfunction of the airbags orpretensioners. Contact your Toyota dealeras soon as possible to service thevehicle.

� The light does not come on when theignition key is turned to the “ON” posi-tion, or the light remains on.

� The light comes on or flashes whiledriving.

� If either front seat belt does not retractor cannot be pulled out due to a mal-function or activation of the relevantfront seat belt pretensioner.

In the following cases, contact your Toyotadealer as soon as possible:

� The front of the vehicle (shaded in theillustration) was involved in an accidentthat was not severe enough to causethe front seat belt pretensioners to op-erate.

� Either front seat belt pretensioner as-sembly or surrounding area isscratched, cracked, or otherwise dam-aged.

The SRS (Supplemental Restraint Sys-tem) front airbags are designed to pro-vide further protection for the driverand front passenger in addition to theprimary safety protection provided bythe seat belts.

In response to a severe frontal impact,the SRS front airbags work together withthe seat belts to help reduce injury byinflating. The SRS front airbags help toreduce injuries mainly to the driver’s orfront passenger’s head or chest caused bydirectly hitting the steering wheel or dash-board. The front passenger airbag is acti-vated even with no passenger in the frontseat.

Be sure to wear your seat belt properly.

SRS driver airbag and frontpassenger airbag



Your vehicle is equipped with a crashsensing and diagnostic module, which willrecord the use of the seat belt restraintsystem by the driver when the SRS air-bags are inflated.

CAUTION

The driver or front passenger who istoo close to the steering wheel ordashboard during airbag deploymentcan be killed or seriously injured.Toyota strongly recommends that:

� The driver sit as far back as pos-sible from the steering wheel whilestill maintaining control of the ve-hicle.

� The front passenger sit as far backas possible from the dashboard.

� All vehicle occupants be properlyrestrained using the available seatbelts.

This indicator comes on when the igni-tion key is turned to the “ON” position.It goes off after about 6 seconds. Thismeans the SRS front airbags are oper-ating properly.

This warning light system monitors theairbag sensor assembly, front airbag sen-sors, side airbag sensors, door side air-bag sensors, front seat belt pretensionerassemblies, inflators, warning light, inter-connecting wiring and power sources. (Fordetails, see “Service remainder indicatorsand warning buzzers” in Section 1−5.)

The SRS front airbag system is de-signed to activate in response to a se-vere frontal impact within the shadedarea between the arrows in the illustra-tion.

The SRS front airbags will deploy if theseverity of the impact is above the de-signed threshold level, comparable to anapproximate 25 km/h (15 mph) collisionwhen impacting straight into a fixed barrierthat does not move or deform.

If the severity of the impact is below theabove threshold level, the SRS front air-bags may not deploy.



However, this threshold velocity will beconsiderably higher if the vehicle strikesan object, such as a parked vehicle orsign pole, which can move or deform onimpact, or if it is involved in an underridecollision (e.g. a collision in which the noseof the vehicle “underrides”, or goes under,the bed of a truck, etc.).

It is possible that in some collisions at thelower zone of airbag sensor detection andactivation the SRS airbags and seat beltpretensioners will not operate all together.

For the safety of all occupants, alwayswear your seat belts properly.

Collision from the rear

Collision from the side

Vehicle rollover

The SRS front airbags are not designedto inflate if the vehicle is involved in aside or rear collision, if it rolls over, orif it is involved in a low−speed frontalcollision.

Hitting a curb, edgeof pavement or hard material

Falling into or jumping over adeep hole

Landing hard or vehicle falling

The SRS front airbags may deploy if aserious impact occurs to the undersideof your vehicle. Some examples areshown in the illustration.



The SRS airbag system consists mainly ofthe following components, and their loca-tions are shown in the illustration.

1. Front airbag sensors


3. Airbag module for front passenger (airbag and inflator)


5. Airbag module for driver (airbag and inflator)

The airbag sensor assembly consists of asafing sensor and airbag sensor.

In a severe frontal impact, the sensorsdetect deceleration and the system trig-gers the airbag inflators. Then a chemicalreaction in the inflators quickly fills theairbags with non−toxic gas to help restrainthe forward motion of the occupants.

When the airbags inflate, they produce afairly loud noise and release some smokeand residue along with non−toxic gas. Thisdoes not indicate a fire. This gas is nor-mally harmless; however, for those whohave delicate skin, it may cause a minorskin irritation. Be sure to wash off anyresidue as soon as possible to preventany potential skin irritation.

Deployment of the airbags happens in afraction of a second, so the airbags mustinflate with considerable force. While thesystem is designed to reduce serious inju-ries, it may also cause minor burns orabrasions and swelling.

Parts of the airbag module (steering wheelhub, dashboard) may be hot for severalminutes, but the airbags themselves willnot be hot. The airbags are designed toinflate only once.

A crash severe enough to inflate the air-bags may break the windshield as thevehicle buckles. In vehicles with a pas-senger airbag the windshield may also bedamaged by absorbing some of the forceof the inflating airbag.



CAUTION

� The SRS airbag system is designedonly as a supplement to the prima-ry protection of the driver side andfront passenger side seat belt sys-tems. The front seat occupants canbe killed or seriously injured by theinflating airbags if they do not wearthe available seat belts properly.During sudden braking just beforea collision, an unrestrained driveror front passenger can move for-ward into direct contact with orclose proximity to the airbag whichmay then deploy during the colli-sion. To ensure maximum protectionin an accident, the driver and allpassengers in the vehicle mustwear their seat belts properly. Wear-ing a seat belt properly during anaccident reduces the chances ofdeath or serious injury or beingthrown out of the vehicle. Forinstructions and precautions con-cerning the seat belt system, see“Seat belts” in this section.

� Improperly seated and/or restrainedinfants and children can be killedor seriously injured by the deploy-ing front airbags. An infant or childwho is too small to use a seat beltshould be properly secured using achild restraint system. Toyotastrongly recommends that all in-fants and children be placed in therear seat of the vehicle and proper-ly restrained. The rear seat is thesafest for infants and children. Forinstructions concerning the installa-tion of a child restraint system, see“Child restraint” in this section. � Never install a rear−facing child re-

straint system on the front passen-ger seat because the force of therapid inflation of the front passen-ger airbag can cause death or seri-ous injury to the child.



Move seatfully back

� A forward−facing child restraint sys-tem should be allowed to beinstalled on the front passengerseat only when it is unavoidable.Always move the seat as far backas possible, because the force ofthe deploying front passenger air-bag could cause death or seriousinjury to the child.

� On vehicles with side airbags, donot allow the child to lean againstthe front door or around the frontdoor even if the child is seated inthe child restraint system. It is dan-gerous if the side airbags inflate,because the impact could causedeath or serious injury to the child.

� For instructions concerning theinstallation of a child restraint sys-tem, see “Child restraint” in thissection.

� Do not sit on the edge of the seator lean over the dashboard whenthe vehicle is in use. The front air-bags inflate with considerablespeed and force; you may be killedor seriously injured. Sit up straightand well back in the seat, and al-ways use your seat belt properly.



� Do not allow a child to stand up,or to kneel on the front passengerseat. The front airbag inflates withconsiderable speed and force; thechild may be killed or seriously in-jured.

� Do not hold a child on your lap orin your arms. Use a child restraintsystem in the rear seat. For instruc-tions concerning the installation ofa child restraint system, see “Childrestraint” in this section.

� Do not put objects or your pets onor in front of the dashboard orsteering wheel pad that houses thefront airbag system. They might re-strict inflation or cause death orserious injury as they are projectedrearward by the force of deployingairbags. Likewise, the driver andfront passenger should not holdthings in their arms or on theirknees.

� Do not modify or remove any wir-ing. Do not modify, remove, strikeor open any components such asthe steering wheel pad, steeringwheel, column cover, front passen-ger airbag cover, front passengerairbag or airbag sensor assembly.Doing so may cause sudden SRSfront airbag inflation or disable thesystem, which could result in deathor serious injury.

Failure to follow these instructionscan result in death or serious injury.Consult your Toyota dealer about anyrepairs and modifications.



NOTICE

Do not perform any of the followingchanges without consulting yourToyota dealer. Such changes can in-terfere with proper operation of theSRS front airbag system in somecases.



� Modification of the front end struc-ture

� Attachment of a grille guard (bullbar, kangaroo bar, etc.), snowplow,winches or any other equipment tothe front end

� Repairs made on or near the frontfenders, front end structure, con-sole, steering column, steeringwheel or dashboard near the frontpassenger airbag

This SRS front airbag system has aservice reminder indicator to inform thedriver of operating problems. If either ofthe following conditions occurs, this indi-cates a malfunction of the airbags. Con-tact your Toyota dealer as soon as pos-sible to service the vehicle.




� The SRS front airbags have been in-flated.

� The front of the vehicle (shaded in theillustration) was involved in an accidentthat was not severe enough to causethe SRS front airbags to inflate.

� The pad section of the steering wheelor front passenger airbag cover(shaded in the illustration) is scratched,cracked, or otherwise damaged.

NOTICE

Do not disconnect the battery cablesbefore contacting your Toyota dealer.



The SRS (Supplemental Restraint Sys-tem) side airbags are designed to pro-vide further protection for the driverand front passenger in addition to theprimary safety protection provided bythe seat belts.

In response to a severe side impact, theSRS side airbags work together with theseat belts to help reduce injury by inflat-ing. The SRS side airbags help to reduceinjuries mainly to the driver’s or front pas-senger’s chest. The SRS side airbag onthe passenger seat is activated even withno passenger in the front seat.

Be sure to wear your seat belt properly.

Your vehicle is equipped with a crashsensing and diagnostic module, which willrecord the use of the seat belt restraintsystem by the driver when the SRS sideairbags are inflated.

CAUTION

SRS side airbags inflate with consid-erable force. To avoid potential deathor serious injury when they inflate,the driver and front passenger must:

� Wear their seat belts properly.

� Remain properly seated with theirback upright and against the seat atall times.

This indicator comes on when the igni-tion key is turned to the “ON” position.It goes off after about 6 seconds. Thismeans the SRS side airbags are operat-ing properly.

This warning light system monitors theairbag sensor assembly, front airbag sen-sors, side airbag sensors, door side air-bag sensors, front seat belt pretensionerassemblies, inflators, warning light, inter-connecting wiring and power sources. (Fordetails, see “Service reminder indicatorsand warning buzzers” in Section 1−5.)

SRS side airbags



The SRS side airbag system may notactivate if the vehicle is subjected to acollision from the side at certainangles, or a collision to the side of thevehicle body other than the passengercompartment as shown in the illustra-tion.

The SRS side airbags are designed toinflate when the passenger compartmentarea suffers a severe impact from theside.

For the safety of all occupants, alwayswear your seat belts properly.

Collision from the rear

Collision from the front

Vehicle rollover

The SRS side airbags are not designedto inflate if the vehicle is involved in afront or rear collision, if it rolls over,or if it is involved in a low−speed sidecollision.

The SRS side airbag system consistsmainly of the following components, andtheir locations are shown in the illustra-tion.


2. Door side airbag sensors

3. Side airbag modules (airbag and inflator)

4. Side airbag sensors


The SRS side airbag system is controlledby the airbag sensor assembly. The airbagsensor assembly consists of a safing sen-sor and airbag sensor.



In a severe side impact, the side airbagsensor triggers the side airbag inflators.Then a chemical reaction in the inflatorsquickly fills the airbags with non−toxic gasto help restrain the lateral motion of theoccupants.

When the airbags inflate, they produce afairly loud noise and release some smokeand residue along with non−toxic gas. Thisdoes not indicate a fire. This gas is nor-mally harmless; however, for those whohave delicate skin, it may cause a minorskin irritation. Be sure to wash off anyresidue as soon as possible to preventany potential skin irritation.

Deployment of the airbags happens in afraction of a second, so the airbags mustinflate with considerable force. While thesystem is designed to reduce serious inju-ries, it may also cause minor burns orabrasions and swelling.

Front seats may be hot for several min-utes, but the airbags themselves will notbe hot. The airbags are designed to inflateonly once.

CAUTION

� The SRS side airbag system is de-signed only as a supplement to theprimary protection of the driverside and front passenger side seatbelt systems. To ensure maximumprotection in an accident, the driverand all passengers in the vehiclemust wear their seat belts properly.Wearing a seat belt properly duringan accident reduces the chances ofdeath or serious injury or beingthrown out of the vehicle. Forinstructions and precautions con-cerning the seat belt system, see“Seat belts” in this section.

� Improperly seated and/or restrainedinfants and children can be killedor seriously injured by the deploy-ing airbags. An infant or child whois too small to use a seat beltshould be properly secured using achild restraint system. Toyotastrongly recommends that all in-fants and children be placed in therear seat of the vehicle and proper-ly restrained. The rear seat is thesafest for infants and children. Forinstructions concerning the installa-tion of a child restraint system, see“Child restraint” in this section.

� Do not allow a child to lean his/herhead or any part of his/her bodyagainst the front door or the areaof the seat from which the side air-bag deploys even if he/she isseated in the child restraint system.It is dangerous if the side airbaginflates, and the impact could causedeath or serious injury to the child.For instructions concerning theinstallation of a child restraint sys-tem, see “Child restraint” in thissection.



� Do not lean against the front doorwhen the vehicle is in use. Other-wise, the side airbag inflates withconsiderable speed and force; youmay be killed or seriously injured.Special care should be taken espe-cially when you have a small childin the vehicle.

� Sit up straight and well back in theseat, distributing your weight evenlyin the seat. Do not apply excessiveweight to the outer side of the frontseats on vehicles with side airbags.

� Do not attach a cup holder or anyother device or object on or aroundthe door. When the side airbag in-flates, the cup holder or any otherdevice or object will be thrown withgreat force or the side airbag maynot activate correctly, resulting indeath or serious injury. Likewise,the driver and front passengershould not hold things in theirarms or on their knees.

� Do not use accessories for theseats which cover the parts wherethe side airbags inflate. Such acces-sories may prevent the side airbagsfrom activating correctly, causingdeath or serious injury.

� Do not modify or replace the seatsor upholstery of front seats withside airbags. Such changes maydisable the system or cause theside airbags to inflate accidentally,resulting in death or serious injury.

Failure to follow these instructionscan result in death or serious injury.Consult your Toyota dealer about anyrepairs and modifications.



NOTICE

Do not perform any of the followingchanges without consulting yourToyota dealer. Such changes caninterfere with proper operation of theSRS side airbag system in somecases.



� Modification of the side structure ofthe passenger compartment

� Repairs made on or near the con-sole or front seat

This SRS side airbag system has aservice reminder indicator to inform thedriver of operating problems. If either ofthe following conditions occurs, thisindicates a malfunction of the airbags.Contact your Toyota dealer as soon aspossible to service the vehicle.




� The SRS side airbags have been in-flated.

� The portion of the doors (shaded in theillustration) was involved in an accidentthat was not severe enough to causethe SRS side airbags to inflate.

� The surface of the seats with the sideairbag (shaded in the illustration) isscratched, cracked, or otherwise dam-aged.



NOTICE

Do not disconnect the battery cablesbefore contacting your Toyota dealer.

Toyota strongly urges the use of childrestraint systems for children smallenough to use them.

The laws of all fifty states in the U.S.A.and Canada now require the use of achild restraint system.

Your vehicle conforms to SAEJ1819.

If a child is too large for a child restraintsystem, the child should sit in the rearseat and must be restrained using thevehicle’s seat belt. See “Seat belts” fordetails.

CAUTION

� For effective protection in automo-bile accidents and sudden stops, achild must be properly restrained,using a seat belt or child restraintsystem depending on the age andsize of the child. Holding a child inyour arms is not a substitute for achild restraint system. In an acci-dent, the child can be crushedagainst the windshield, or betweenyou and the vehicle’s interior.

� Toyota strongly urges use of aproper child restraint system whichconforms to the size of the child,installed on the rear seat. Accord-ing to accident statistics, the childis safer when properly restrained inthe rear seat than in the front seat.

� Never install a rear−facing child re-straint system on the front seat. Inthe event of an accident, the forceof the rapid inflation of the airbagcan cause death or serious injury ifa rear−facing child restraint systemis installed on the front seat.

� Unless it is unavoidable, do notinstall a forward−facing child re-straint system on the front seat.

Child restraint——Child restraint precautions





� Make sure that you have compliedwith all installation instructions pro-vided by the child restraintmanufacturer and that the system isproperly secured.

A child restraint system for a smallchild or baby must itself be properlyrestrained on the seat with the lap por-tion of the lap/shoulder belt. You mustcarefully consult the manufacturer’s in-structions which accompany the childrestraint system.

To provide proper restraint, use a childrestraint system following the manufactur-er’s instructions about the appropriate ageand size of the child for the child restraintsystem.

Install the child restraint system correctlyfollowing the instructions provided by itsmanufacturer. General directions are alsoprovided under the following illustrations.

The child restraint system should beinstalled on the rear seat. According toaccident statistics, the child is safer whenproperly restrained in the rear seat thanin the front seat.

CAUTION

� Never install a rear−facing child re-straint system on the front seat. Inthe event of an accident, the forceof the rapid inflation of the airbagcan cause death or serious injury ifa rear−facing child restraint systemis installed on the front seat.

� Unless it is unavoidable, do notinstall a forward−facing child re-straint system on the front seat.



—Child restraint system



� After installing the child restraintsystem, make sure it is secured inplace following the manufacturer’sinstructions. If it is not restrainedsecurely, it may cause death or se-rious injury to the child in theevent of a sudden stop or accident.

When not using the child restraint system,keep it secured with the seat belt or placeit somewhere other than the passengercompartment. This will prevent it from in-juring passengers in the event of a sud-den stop or accident.

Your vehicle has anchors for securing thetop strap of a child restraint system.

For instructions on how to use the anchorbracket, see “—Using a top strap” in thissection.

Child restraint systems are divided intothe following 3 types according to thechild’s age and size.

(A) Infant seat

(B) Convertible seat

(C) Booster seat

Install the child restraint system followingthe instructions provided by its manufac-turer.

(A) Infant seat

(B) Convertible seat

—Types of child restraintsystem



(C) Booster seat(A) INFANT SEAT INSTALLATION

An infant seat is used in rear−facingposition only.

CAUTION

� Never install a rear−facing child re-straint system on the front passen-ger seat because the force of therapid inflation of the front passen-ger airbag can cause death or seri-ous injury to the child.

—Installation with 3−pointtype seat belt



� Do not install a rear−facing childrestraint system on the rear seat ifit interferes with the lock mecha-nism of the front seats. This cancause death or serious injury to thechild and front passenger in caseof sudden braking or a collision.

� If the driver’s seat position doesnot allow sufficient space for safeinstallation, install the child re-straint system at another position.

1. Run the lap and shoulder belt throughor around the infant seat following theinstructions provided by its manufactur-er and insert the tab into the buckletaking care not to twist the belt. Keepthe lap portion of the belt tight.

CAUTION

� After inserting the tab, make surethe tab and buckle are locked andthat the lap and shoulder portionsof the belt is not twisted.

� Do not insert coins, clips, etc. inthe buckle as this can prevent youfrom properly latching the tab andbuckle.

� If the seat belt does not functionnormally, it cannot protect yourchild from injury. Contact yourToyota dealer immediately. Do notuse the child restraint seat until theseat belt is fixed.



2. Fully extend the shoulder belt to put itin the lock mode. When the belt isthen retracted even slightly, it cannotbe extended.

To hold the infant seat securely, makesure the belt is in the lock mode beforeletting the belt retract.

3. While pressing the infant seat firmlyagainst the seat cushion and seatback,let the shoulder belt retract as far asit will go to hold the infant seat secure-ly.

CAUTION

Push and pull the child restraint sys-tem in different directions to be sureit is secure. Follow all the installationinstructions provided by its manufac-turer.



4. To remove the infant seat, press thebuckle−release button and allow thebelt to retract completely. The belt willmove freely again and be ready towork for an adult or older child passen-ger.

(B) CONVERTIBLE SEAT INSTALLATION

A convertible seat is used in forward−facing or rear−facing position depend-ing on the child’s age and size. Wheninstalling, follow the manufacturer’s in-struction about the applicable child’sage and size as well as directions forinstalling the child restraint system.

CAUTION

� Never install a rear−facing child re-straint system on the front passen-ger seat because the force of therapid inflation of the front passen-ger airbag can cause death or seri-ous injury to the child.



Move seatfully back



� Do not put a rear−facing child re-straint system on the rear seat if itinterferes with the lock mechanismof the front seats. This can causedeath or serious injury to the childand front passenger in case of sud-den braking or a collision.

� If your driving position is not satis-factory, install the child restraintsystem at another position.



1. Run the lap and shoulder belt throughor around the convertible seat followingthe instructions provided by itsmanufacturer and insert the tab intothe buckle taking care not to twist thebelt. Keep the lap portion of the belttight.

CAUTION

� After inserting the tab, make surethe tab and buckle are locked andthat the lap and shoulder portionsof the belt is not twisted.


� If the seat belt does not functionnormally, it cannot protect yourchild from injury. Contact yourToyota dealer immediately. Do notuse the seat until the seat belt isfixed.

2. Fully extend the shoulder belt to put itin the lock mode. When the belt isthen retracted slightly, it cannot be ex-tended.

To hold the convertible seat securely,make sure the belt is in the lock modebefore letting the belt retract.



3. While pressing the convertible seatfirmly against the seat cushion andseatback, let the shoulder belt retractas far as it will go to hold the convert-ible seat securely.

CAUTION

Push and pull the child restraint sys-tem in different directions to be sureit is secure. Follow all the installationinstructions provided by its manufac-turer.

4. To remove the convertible seat, pressthe buckle−release button and allow thebelt to retract completely. The belt willmove freely again and be ready towork for an adult or older child passen-ger.



(C) BOOSTER SEAT INSTALLATION

A booster seat is used in forward−fac-ing position only.

Move seatfully back

CAUTION

� A forward−facing child restraint sys-tem should be allowed to be put onthe front passenger seat only whenit is unavoidable. Always move theseat as far back as possible, be-cause the force of the deployingfront passenger airbag could causedeath or serious injury to the child.

� On vehicles with side airbags, donot allow the child to lean againstthe front door or around the frontdoor even if the child is seated inthe child restraint system. It is dan-gerous if the side airbag inflates,and the impact could cause deathor serious injury to the child.



1. Sit the child on a booster seat. Runthe lap and shoulder belt through oraround the booster seat and child fol-lowing the instructions provided by itsmanufacturer and insert the tab intothe buckle taking care not to twist thebelt.

Make sure the shoulder belt is correctlyacross the child’s shoulder and that thelap belt is positioned as low as possibleon child’s hips. See “Seat belts” for de-tails.

CAUTION

� Always make sure the shoulder beltis positioned across the center ofchild’s shoulder. The belt should bekept away from child’s neck, butnot falling off child’s shoulder. Fail-ure to do so could reduce theamount of protection in an accidentand increase the chance of injury.

� Both high−positioned lap belts andloose−fitting belts could cause seri-ous injuries due to sliding underthe lap belt during a collision orother unintended result. Keep thelap belt positioned as low on achild’s hips as possible.

� For child’s safety, do not place theshoulder belt under child’s arm.

� After inserting the tab, make surethe tab and buckle are locked andthat the lap and shoulder portionsof the belt are not twisted.


� If the seat belt does not functionnormally, it cannot protect yourchild from injury. Contact yourToyota dealer immediately. Do notuse the child restraint seat until theseat belt is fixed.



2. To remove the child restraint system,press the buckle−release button and al-low the belt to retract.

Follow the procedure below for a childrestraint system that requires the useof a top strap.

Front of vehicleSymbol

Anchor brackets

Use the anchor bracket on the rear of theseat back to attach the top strap.

Anchor brackets are installed for eachrear seating position.

This symbol indicates the locations of an-chor brackets.

—Using a top strap



TO USE THE ANCHOR BRACKET:

1. Find the label on the rear of the seatback carpet. Tear the slit next to thelabel by hand.

2. Fix the child restraint system withthe seat belt.

Latch the hook onto the exposed an-chor bracket and tighten the topstrap.

For instructions to install the child re-straint system, see “Child restraint” in thissection.

CAUTION

Make sure the top strap is securelylatched, and check that the child re-straint system is secure by pushingand pulling it in different directions.Follow all the installation instructionsprovided by its manufacturer.



Slide the back−plate of the flap under thecarpet to cover the anchor bracket whenit is not in use.

To change the steering wheel angle,hold the steering wheel, push the lockrelease lever, tilt the steering wheel tothe desired angle and return the leverto its original position.

CAUTION

� Do not adjust the steering wheelwhile the vehicle is moving. It maycause the driver to mishandle thevehicle and an accident may occurresulting in death or serious inju-ries.

� After adjusting the steering wheel,try moving it up and down to makesure it is locked in position.

Adjust the mirror so that you can seethe side of your vehicle in the mirror.

Be careful when judging the size or dis-tance of any object seen in the outsiderear view mirror on the passenger’s side.It is a convex mirror with a curved sur-face. Any object seen in a convex mirrorwill look smaller and farther away thanwhen seen in a flat mirror.

CAUTION

Do not adjust the mirror while thevehicle is moving. It may cause thedriver to mishandle the vehicle andan accident may occur resulting indeath or serious injuries.

Tilt steering wheel Outside rear view mirrors—



To adjust a mirror, use the switches.

1. Master switch—To select the mirror tobe adjustedPush the “L” (left) or “R” (right) switch.

2. Control switch—To move the mirrorPush the switch in the desired direc-tion.

Mirror can be adjusted when the key is inthe “ACC” or “ON” position.

NOTICE

If ice should jam the mirror, do notoperate the control or scrape the mir-ror face. Use a spray de−icer to freethe mirror.

The rear view mirrors can be foldedbackward for parking in restrictedareas.

To fold the rear view mirror, push back-ward.

CAUTION

Do not drive with the mirrors foldedbackward. Both the driver and pas-senger side rear view mirrors mustbe extended and properly adjustedbefore driving.

Adjust the mirror so that you can justsee the rear of your vehicle in the mir-ror.

To reduce glare from the headlights ofthe vehicle behind you during nightdriving, operate the lever on the loweredge of the mirror.

Daylight driving—Lever at position 1

The reflection in the mirror has greaterclarity at this position.

Night driving—Lever at position 2

Remember that by reducing glare you alsolose some rear view clarity.

—Power rear view mirrorcontrol —Folding rear view mirrors

Anti−glare inside rear viewmirror



CAUTION

Do not adjust the mirror while thevehicle is moving. It may cause thedriver to mishandle the vehicle andan accident may occur resulting indeath or serious injuries.

To use the vanity mirror, swing downthe sun visor and open the cover.

Vanity mirrors





OPERATION OF INSTRUMENTS ANDCONTROLSLights, Wipers and DefoggerHeadlights and turn signals 66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency flashers 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Instrument panel light control 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front fog lights 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interior light 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Luggage compartment light 70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Windshield wipers and washer 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear window wiper and washer 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rear window defogger 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 4



Type A

Type B

HEADLIGHTS

To turn on the following lights: Twistthe headlight/turn signal lever knob.

Position 1—Parking, tail, license plate,side marker and instrument panel lights

Type B only—The tail light indicator (greenlight) on the instrument panel will tell youthat the tail lights are on.

Position 2—Headlights and all of theabove

Type A only—The headlight low beam indi-cator light (green light) on the instrumentpanel will tell you that the low beams areon.

Light reminder buzzer

A buzzer will remind you to turn the lightsoff when the driver’s door is opened if youremove the key with the headlights lefton.

NOTICE

To prevent the battery being dis-charged, do not leave the lights onfor a long period when engine is notrunning.

Daytime running light system

The headlights turn on at reduced intensi-ty when the parking brake is released withthe engine started, even with the lightswitch in the “OFF” position or position 1.They will not go off until the ignitionswitch is turned off.

Twist the knob to the position 2 to turnto full intensity for driving at night.

The headlights automatically turn to fullintensity in the twilight even with the lightswitch in the “OFF” position.

Headlights and turn signals



The daytime running light control sensoris on the top of the driver’s side instru-ment panel.

Do not place anything on the instrumentpanel, and/or do not affix anything on thewindshield to block this sensor.

High−low beams—For high beams, turnthe headlights on and push the lever awayfrom you (position 1). Pull the lever to-ward you (position 2) for low beams.

The headlight high beam indicator light(blue light) on the instrument panel willtell you that the high beams are on.

Flashing the high beam headlights(position 3)—Pull the lever all the wayback. The high beam headlights turn offwhen you release the lever.

You can flash the high beam headlightswith the knob turned to “OFF”.

TURN SIGNALS

To signal a turn, push the headlight/turn signal lever up or down to position1.

The key must be in the “ON” position.

The lever automatically returns after youmake a turn, but you may have to returnit by hand after you change lanes.

To signal a lane change, move the leverup or down to the pressure point (position2) and hold it.

If the turn signal indicator lights (greenlights) on the instrument panel flash fasterthan normal, a front or rear turn signalbulb is burned out.



To turn on the emergency flashers,push the switch.

All the turn signal lights will flash. To turnthem off, push the switch once again.

Turn on the emergency flashers to warnother drivers if your vehicle must bestopped where it might be a traffic hazard.

Always pull as far off the road as pos-sible.

The turn signal light switch will not workwhen the emergency flashers are operat-ing.

NOTICE

To prevent the battery from being dis-charged, do not leave the switch onlonger than necessary when the en-gine is not running.

To adjust the brightness of the instru-ment panel lights, turn the knob.

Emergency flashers Instrument panel light control



To turn on the front fog lights, twistthe band of the headlight and turn sig-nal switch lever. They will come ononly when the headlights are on lowbeam.

To turn the interior light on, push the“ON” or “DOOR” side switch. To turnthe light off, push the switch lightly onthe opposite side.

The interior light switch has the followingpositions:

“ON”—The light stays on all the time.

“DOOR”—Turns the light on when any ofthe side doors and back is opened. Thelight fades out when both side doors andback door are closed.

ILLUMINATED ENTRY SYSTEM(vehicles with power door lock system)

With the switch in “DOOR” position, thelight comes on when any of the sidedoors and back door is opened. After bothside doors and back door are closed, thelight remains on for about 15 seconds andfades out.

However, in the following cases, the lightfades out immediately.

� Both side doors and back door areclosed when the ignition key is in“ACC” or “ON” position.

� Both side doors and back door areclosed and both side doors are locked.

When both side doors and back door areunlocked simultaneously with a key orwireless remote control transmitter, the in-terior light comes on for about 15 secondsand then fades out, even if the door isnot opened.

To prevent the battery being discharged,the lights will automatically turn off whenthe key is removed and the door is leftopened with the switch at “DOOR” positionfor 20 minutes or more.

Front fog lightsInterior light (with moon roof)



To turn on the interior light, slide theswitch.

The interior light switch has the followingpositions:

“ON”—The light stays on all the time.

“OFF”—Turns the light off.

“DOOR”—Turns the light on when any ofthe side doors and back door is opened.The light fades out when both side doorsand back door are closed.

ILLUMINATED ENTRY SYSTEM(vehicles with power door lock system)

With the switch in “DOOR” position, thelight comes on when any of the sidedoors and back door is opened. After bothside doors and back door are closed, thelight remains on for about 15 seconds andfades out.

However, in the following cases, the lightfades out immediately.

� Both side doors and back door areclosed when the ignition key is in“ACC” or “ON” position.

� Both side doors and back door areclosed and both side doors are locked.

When both side doors and back door areunlocked simultaneously with a key orwireless remote control transmitter, the in-terior light comes on for about 15 secondsand then fades out, even if the door isnot opened.

To prevent the battery being discharged,the lights will automatically turn off whenthe key is removed and the door is leftopened with the switch at “DOOR” positionfor 20 minutes or more.

To turn the luggage compartment lighton, open the back door and push theswitch. Closing the back door will turnthe light off.

Interior light (without moon roof) Luggage compartment light



To turn on the windshield wipers, movethe lever to the desired setting.


Lever position Speed setting

Position 1 Intermittent

Position 2 Slow

Position 3 Fast

For a single sweep of the windshield,push the lever up and release it.

With interval adjuster: The “INT TIME”band lets you adjust the wiping time inter-val when the wiper lever is in the intermit-tent position (position 1). Twist the bandupward to increase the time betweensweeps, and downward to decrease it.

To squirt washer fluid, pull the levertoward you.

If the windshield wipers are off, they willoperate a couple of times after the washersquirts.

For instructions on adding washer fluid,see “Adding washer fluid” in Section 7−3.

In freezing weather, warm the windshieldwith the defroster before using the washer.This will help prevent the washer fluidfrom freezing on your windshield, whichcan block your vision.

NOTICE

Do not operate the wipers if the wind-shield is dry. It may scratch theglass.

To turn on the rear window wiper, twistthe lever knob upward.


Lever position Speed setting

Position 1 Intermittent

Position 2 Normal

To squirt washer fluid on the rear window,twist the knob upward or downward as faras it will go (position 3 or 4). The knobautomatically returns from these positionsafter you release it.

For instructions on adding washer fluid,see “Adding washer fluid” in Section 7−3.

Windshield wipers and washerRear window wiper andwasher



NOTICE

Do not operate the rear wiper if therear window is dry. It may scratch theglass.

To defog or defrost the rear window,push the switch.


The thin heater wires on the inside of therear window will quickly clear the surface.An indicator light will illuminate to indicatethe defogger is operating.

Push the switch once again to turn thedefogger off.

The system will automatically shut off af-ter the defogger has operated about 15minutes.

Make sure you turn the defogger off whenthe window is clear. Leaving the defoggeron for a long time could cause the batteryto discharge, especially during stop−and−go driving. The defogger is not designedfor drying rain water or for melting snow.

NOTICE

When cleaning the inside of the rearwindow, be careful not to scratch ordamage the heater wires or connec-tors.

Rear window defogger



OPERATION OF INSTRUMENTS ANDCONTROLSGauges, Meters and Service reminder indicatorsFuel gauge 74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine coolant temperature gaugege 74. . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer 75. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Odometer and two trip meters 76. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzersrs 76. . . . . . . . . . . . . .

SECTION 1− 5



The gauge works when the ignitionswitch is on and indicates the approxi-mate quantity of fuel remaining in thetank.

Nearly full—Indicator at “F”Nearly empty—Indicator at “E”

It is a good idea to keep the tank over1/4 full.

If the fuel level approaches “E” or the lowfuel level warning light comes on, fill thefuel tank as soon as possible.

If the fuel tank is full or the fuel quantityhas increased or decreased by more than5 liters since the vehicle was turned off,the position display is recalculated. If thefuel quantity has increased or decreasedby less than 5 liters since the vehicle wasturned off, the previous position is dis-played.

If the fuel tank is completely empty, themalfunction indicator lamp comes on. Fillthe fuel tank immediately.

The indicator lamp goes off after drivingseveral times. If the indicator lamp doesnot go off, contact your Toyota dealer assoon as possible.

If the fuel gauge display flashes or theremaining quantity is not displayed afterthe flashing, there may be a problem inthe system. In this case, contact yourToyota dealer as soon as possible.

The gauge indicates the engine coolanttemperature when the ignition switch ison. The engine operating temperaturewill vary with changes in weather andengine load.

If the needle moves to the “H” positionand flashes, your engine is too hot. Ifyour vehicle overheats, stop your vehicleand allow the engine to cool.

Your vehicle may overheat during severeoperating conditions, such as:

� Driving up a long hill on a hot day.

� Reducing speed or stopping after highspeed driving.

� Idling for a long period with the airconditioning on in stop−and−go traffic.

Fuel gaugeEngine coolant temperaturegauge



� Towing a trailer.

If the engine coolant temperature gaugeneedle is not displayed, there may be aproblem in the system. In this case, con-tact your Toyota dealer as soon as pos-sible.

NOTICE

� Do not remove the thermostat inthe engine cooling system as thismay cause the engine to overheat.The thermostat is designed to con-trol the flow of coolant to keep thetemperature of the engine withinthe specified operating range.

� Do not continue driving with anoverheated engine. See “If yourvehicle overheats” in Section 4.

The tachometer indicates engine speedin thousands of rpm (revolutions perminute). Use it while driving to selectcorrect shift points and to prevent en-gine lugging and over−revving.

Driving with the engine running too fastcauses excessive engine wear and poorfuel economy. Remember, in most casesthe slower the engine speed, the greaterthe fuel economy.

NOTICE

� Do not let the indicator needle getinto the red zone. This may causesevere engine damage.

� 2ZZ−GE engine only—The enginewill not exceed 7100 rpm before itwarms up.

Tachometer



This meter displays the odometer andtwo trip meters.

1. Odometer—Shows the total distancethe vehicle has been driven.

2. Two trip meters—Show two differentdistances independently driven sincethe last time each trip meter was setto zero.

You can use one trip meter to calculatethe fuel economy and the other tomeasure the distance on each trip. Alltrip meter data is cancelled if the elec-trical power source is disconnected.

3. Trip meter reset knob—Resets the twotrip meters to zero, and also changethe meter display.

To change the meter display, quicklypush and release the knob. The meterdisplay changes in the order from theodometer to trip meter A to trip meterB, then back to the odometer eachtime you push.

To reset the trip meter A to zero, dis-play the meter A reading, then pushand hold the knob until the meter isset to zero. The same process can beapplied for resetting the trip meter B.

If the indicator orbuzzer comes on...

(a) If parkingbrake is off,stop immediately and contact Toyota dealer.

(b) Fasten driver’s seat belt.

(d) Stop and check.

or

(c) Have the front passenger fastenthe seat belt.

(e) Stop and check.

Do this

Odometer and two trip metersService reminder indicatorsand warning buzzers



(h) Take vehicle toToyota dealer.

If the brake system warning light is also on, stop immediately and contact Toyota dealer.

(g) Fill up tank.

or

(f) Take vehicle toToyota dealer.

(i) Close both sidedoors and backdoor.


Do this

(j) Take vehicle toToyota dealerimmediately.

(k) Stop and check.

(l) Remove key.Key reminderbuzzer

(m) Turn off lights.Light reminderbuzzer


Do this(a) Brake System Warning Light

This light comes on in the following caseswhen the ignition key is in the “ON” posi-tion.

� When the parking brake is applied...

Vehicles with anti−lock brake system—

This light comes on for a few secondswhen the ignition key is turned to the“ON” position even after the parking brakeis released.

� When the brake fluid level is low...

CAUTION

It is dangerous to continue drivingnormally when the brake fluid level islow.

Have your vehicle checked at yourToyota dealer in the following cases:

� The light does not come on even if theparking brake is applied when the igni-tion key is in the “ON” position.

Vehicles with anti−lock brake system—

� The light does not come on even if theignition key is turned on with the park-ing brake released.



A warning light turning on briefly duringoperation does not indicate a problem.

CAUTION

If either of the following conditionsoccurs, immediately stop your vehicleat a safe place and contact yourToyota dealer.

� The light does not turn off evenafter the parking brake is releasedwhile the engine is running.

In this case, the brakes may notwork properly and your stoppingdistance will become longer. De-press the brake pedal firmly andbring the vehicle to an immediatestop.

Vehicles with anti−lock brake sys-tem—

� The brake system warning light re-mains on together with the “ABS”warning light.

In this case, not only the anti−lockbrake system will fail but also thevehicle will become extremely un-stable during braking.

(b) Driver’s Seat Belt Reminder Lightand Buzzer

This light reminds you to buckle up thedriver’s seat belt.

Once the ignition key is turned to “ON” or“START”, the reminder light flashes andbuzzer sounds if the driver’s seat belt isnot fastened. Unless the driver fastens thebelt, the light keeps flashing and thebuzzer stops after about 4 to 8 seconds.

(c) Front Passenger’s Seat BeltReminder Light

This light reminds you to have the frontpassenger buckle up the seat belt.

Once the ignition key is turned to “ON” or“START”, the reminder light flashes if apassenger sits in the front passenger seatand does not fasten the seat belt. Unlessthe front passenger fastens the belt, thelight stays flashing.

If luggage load is placed on the frontpassenger seat, depending on its weightand how it is placed on the seat, built−insensors in the seat cushion may detectthe pressure, causing the reminder light tocome on.

(d) Discharge Warning Light

This light warns that the battery is beingdischarged.

If it comes on while you are driving, thereis a problem somewhere in the chargingsystem.

The engine ignition will continue to oper-ate, however, until the battery is dis-charged. Turn off the air conditioning,blower, radio, etc., and drive directly tothe nearest Toyota dealer or repair shop.

NOTICE

Do not continue driving if the enginedrive belt is broken or loose.

(e) Low Engine Oil Pressure WarningLight

This light warns that the engine oil pres-sure is too low.

If it flickers or stays on while you aredriving, pull off the road to a safe placeand stop the engine immediately. Call aToyota dealer or qualified repair shop forassistance.

The light may occasionally flicker whenthe engine is idling or it may come onbriefly after a hard stop. There is nocause for concern if it then goes out whenthe engine is accelerated slightly.



The light may come on when the oil levelis extremely low. It is not designed toindicate low oil level, and the oil levelmust be checked using the level dipstick.

NOTICE

Do not drive the vehicle with thewarning light on—even for one block.It may ruin the engine.

(f) Malfunction Indicator Lamp

This lamp comes on when the ignitionkey is turned to the “ON” position andgoes off after the engine starts. Thismeans that the warning light system isoperating properly.

If the lamp remains on, or the lampcomes on while driving, first check thefollowings.

� Empty fuel tank

If the fuel tank is empty, refuel immedi-ately.

� Loose fuel tank cap

If the fuel tank cap is loose, securelytighten it.

These cases are temporary malfunctions.The malfunction indicator lamp will go offafter taking several driving trips.

If the lamp will not go off even after theseveral trips, contact your Toyota dealeras soon as possible.

If the fuel tank is not empty or the fueltank cap is not loose...

� There is a problem somewhere in theengine, emission control system, auto-matic transmission electrical system orwarning light system itself.

Contact your Toyota dealer as soon aspossible to service the vehicle.

Emissions Inspection and Maintenance(I/M) programs

Your vehicle may not pass a stateemission inspection if the malfunctionindicator lamp remains on. Contact yourToyota dealer to check your vehicle’semission control system and OBD(On−Board Diagnostics) system beforetaking your vehicle for the inspection.

For details, see “Emissions Inspection andMaintenance (I/M) programs” in Section 6.

(g) Low Fuel Level Warning Light

This light comes on when the fuel levelin the tank becomes nearly empty. Fill upthe tank as soon as possible.

(h) “ABS” Warning Light

The light comes on when the ignition keyis turned to the “ON” position. If the anti−lock brake system works properly, thelight turns off after a few seconds. There-after, if the system malfunctions, the lightcomes on again.

When the “ABS” warning light is on (andthe brake system warning light is off), theanti−lock brake system does not operate,but the brake system still operates con-ventionally.

When the “ABS” warning light is on (andthe brake system warning light is off), theanti−lock brake system does not operateso that the wheels could lock up duringa sudden braking or braking on slipperyroad surfaces.

If either of the following conditionsoccurs, this indicates a malfunctionsomewhere in the parts monitored bythe warning light system. Contact yourToyota dealer as soon as possible toservice the vehicle.

� The light does not come on when theignition key is turned to the “ON” posi-tion, or remains on.

� The light comes on while you are driv-ing.




CAUTION

If the “ABS” warning light remains ontogether with the brake system warn-ing light, immediately stop your ve-hicle at a safe place and contact yourToyota dealer.

In this case, not only the anti−lockbrake system will fail but also thevehicle will become extremely unsta-ble during braking.

(i) Open Door Warning Light

This light remains on until both side doorsand back door are completely closed.

(j) SRS Warning Light

This light will come on when the igni-tion key is turned to the “ON” position.After about 6 seconds, the light will gooff. This means the systems of the air-bag and front seat belt pretensionersare operating properly.

The warning light system monitors the air-bag sensor assembly, front airbag sen-sors, side airbag sensors, door side air-bag sensors, front seat belt pretensionerassemblies, inflators, warning light, inter-connecting wiring and power sources.

If either of the following conditions occurs,this indicates a malfunction somewhere inthe parts monitored by the warning lightsystem. Contact your Toyota dealer assoon as possible to service the vehicle.



(k) Automatic Transmission FluidTemperature Warning Light

This light warns that the automatic trans-mission fluid temperature is too high.

If this light comes on while you are driv-ing, slow down and pull off the road. Stopthe vehicle at a safe place and put theselector lever in “P”. With the engine id-ling, wait until the light goes off. If thelight goes off, you may start the vehicleagain. If the light does not go off, call aToyota dealer or qualified repair shop forassistance.

(l) Key Reminder Buzzer

This buzzer reminds you to remove thekey when you open the driver’s door withthe ignition key in the “ACC” or “LOCK”position.

(m) Light reminder buzzer

The buzzer will sound if the headlightswitch is left on and the driver’s door isopened with the key removed from theignition switch.

CHECKING SERVICE REMINDERINDICATORS (except the low fuel levelwarning light)

1. Apply the parking brake.

2. Open either side door or the backdoor. The open door warning light shouldcome on.

3. Close the door.The open door warning light should gooff.

4. Turn the ignition key to “ON”, but donot start the engine.All the service reminder indicators ex-cept the open door warning light shouldcome on. The “ABS” warning light goesoff after a few seconds. The SRSwarning light goes off after about 6seconds.

If any service reminder indicator or warn-ing buzzer does not function as describedabove, have it checked by your Toyotadealer as soon as possible.



OPERATION OF INSTRUMENTS ANDCONTROLSIgnition switch, Transmission and Parking brakeIgnition switch with steering lock 82. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual transmission 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake 94. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cruise control 95. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 6



“START”—Starter motor on. The keywill return to the “ON” position whenreleased.

For starting tips, see Section 3.

“ON”—Engine on and all accessorieson.

This is the normal driving position.

“ACC”—Accessories such as the radiooperate, but the engine is off.

If you leave the key in the “ACC” or“LOCK” position and open the driver’sdoor, a buzzer will remind you to removethe key.

“LOCK”—Engine is off and the steeringwheel is locked. The key can be re-moved only at this position.

You must push in the key to turn the keyfrom “ACC” to the “LOCK” position. Onvehicles with an automatic transmission,the selector lever must be in the “P” posi-tion before pushing the key.

When starting the engine, the key mayseem stuck at the “LOCK” position. Tofree it, first be sure the key is pushed allthe way in, and then rock the steeringwheel slightly while turning the key gently.

CAUTION

For manual transmission:

Never remove the key when the ve-hicle is moving, as this will lock thesteering wheel and result in loss ofsteering control.

NOTICE

Do not leave the key in the “ON”position if the engine is not running.The battery will discharge and theignition could be damaged.

Ignition switch with steeringlock



Your automatic transmission has a shiftlock system to minimize the possibility ofincorrect operation. This means you canonly shift out of “P” position when thebrake pedal is depressed (with the ignitionswitch in “ON” position and the lock re-lease button depressed).

(a) Selector lever

The shift position is also displayed on theinstrument cluster.

P: Parking, engine starting andkey removal

R: Reverse

N: Neutral

D: Normal driving (with overdrive on)

2: Stronger engine braking

L: Maximum engine braking

Automatic transmission�1ZZ−FE engine

Lock release buttonTo prevent misshifting

With the brake pedal depressed,shift while holding the lock releasebutton in. (The ignition switchmust be in “ON” position.)

Shift while holding the lockrelease button in.

Shift normally.

Overdrive switch

Selector lever



(b) Overdrive switch

You can select either third gear (withoverdrive off) or fourth gear (with over-drive on) by pushing this switch.

To turn the overdrive off, push the switch.The “O/D OFF” indicator light should comeon. To turn the overdrive on again, pushthe switch again. The “O/D OFF” indicatorlight should go off.

Always drive your vehicle with the over-drive on for better fuel economy andquieter driving.

If the engine is turned off when the over-drive is off and restarted, the overdrivewill automatically be on.

Vehicles with cruise control—When thecruise control is being used, even if youdownshift the transmission by pushing andreleasing the overdrive switch, enginebraking will not be enabled because thecruise control is not cancelled.

For ways to decrease the vehicle speed,see “Cruise control” in this section.

(c) Normal driving

1. Start the engine as instructed in “Howto start the engine” in Section 3. Thetransmission must be in “P” or “N”.

2. With your foot holding down the brakepedal, shift the selector lever to “D”.

When the lever is in the “D” position, theautomatic transmission system will selectthe most suitable gear for running condi-tions such as normal cruising, hill climb-ing, hard towing, etc.

Always turn the overdrive on for betterfuel economy and quieter driving. If theengine coolant temperature is low, thetransmission will not shift into the over-drive gear even with the overdrive on.

CAUTION

Never put your foot on the accelera-tor pedal while shifting.

3. Release the parking brake and brakepedal. Depress the accelerator pedalslowly for smooth starting.

(d) Using engine braking

To use engine braking, you can downshiftthe transmission as follows:

� Push the overdrive switch. The “O/DOFF” indicator light will come on andthe transmission will downshift to thirdgear.

� Shift into the “2” position. The trans-mission will downshift to second gearwhen the vehicle speed drops down toor lower than 101 km/h (63 mph), andstronger engine braking will be en-abled.

� Shift into the “L” position. The trans-mission will downshift to first gearwhen the vehicle speed drops down toor lower than 50 km/h (31 mph), andmaximum engine braking will be en-abled.





CAUTION

Be careful when downshifting on aslippery surface. Abrupt shiftingcould cause the vehicle to spin orskid.

(e) Using the “2” and “L” positions

The “2” and “L” positions are used forstrong engine braking as described pre-viously.

With the selector lever in “2” or “L”, youcan start the vehicle in motion as with thelever in “D”.

With the selector lever in “2”, the vehiclewill start in first gear and automaticallyshift to second gear.

With the selector lever in “L”, the trans-mission is engaged in first gear.

NOTICE

� Be careful not to over−rev the en-gine. Watch the tachometer to keepengine rpm from going into the redzone. The approximate maximum al-lowable speed for each position isgiven below for your reference:

“2” 124 km/h (77 mph). . . . . . . . . . . “L” 67 km/h (41 mph). . . . . . . . . . . .

� Do not continue hill climbing orhard towing for a long time in the“2” or “L” position. This may causesevere automatic transmission dam-age from overheating. To preventsuch damage, “D” position shouldbe used in hill climbing or hardtowing.

(f) Backing up

1. Bring the vehicle to a complete stop.

2. With the brake pedal held down withyour foot, shift the selector lever to the“R” position.

NOTICE

Never shift into reverse while the ve-hicle is moving.

(g) Parking


2. Pull the parking brake lever up fully tosecurely apply the parking brake.

3. With the brake pedal pressed down,shift the selector lever to the “P” posi-tion.

CAUTION

Never attempt to move the selectorlever into “P” position under any cir-cumstances while the vehicle is mov-ing. Serious mechanical damage andloss of vehicle control may result.

(h) Good driving practice

� If the transmission repeatedly shifts upand down between third gear and over-drive when climbing a gentle slope, theoverdrive should be turned off. Be sureto turn the switch on immediately after-ward.

� When towing a trailer, in order to main-tain engine braking efficiency, do notuse overdrive.



CAUTION

Always keep your foot on the brakepedal while stopped with the enginerunning. This prevents the vehiclefrom creeping.

NOTICE

Do not hold the vehicle on an up-grade with the accelerator pedal. Itcan cause the transmission to over-heat. Always use the brake pedal orparking brake.

(i) Rocking your vehicle in stuck

CAUTION

If your vehicle becomes stuck insnow, mud, sand, etc., then you mayattempt to rock the vehicle free bymoving it forward and backward. Donot attempt this procedure if peopleor objects are anywhere near the ve-hicle. During the rocking operationthe vehicle may suddenly move for-ward or backward as it becomes un-stuck, causing injury or damage tonearby people or objects.

NOTICE

If you rock your vehicle, observe thefollowing precautions to prevent dam-age to the transmission and otherparts.

� Do not depress the accelerator ped-al while shifting the selector leveror before the transmission is com-pletely shifted to forward or reversegear.

� Do not race the engine and avoidspinning the wheels.

� If your vehicle remains stuck afterrocking the vehicle several times,consider other ways such as tow-ing.

(j) If you cannot shift the selector le-ver out of “P” position

If you cannot shift the selector lever fromthe “P” position even though the brakepedal is depressed, use the shift lockoverride button. For instructions, see “Ifyou cannot shift automatic transmissionselector lever” in Section 4.



Your automatic transmission has a shiftlock system to minimize the possibility ofincorrect operation. This means you canonly shift out of “P” position when thebrake pedal is depressed (with the ignitionswitch in “ON” position and the lock re-lease button depressed).

(a) Selector lever

The shift position is also displayed on theinstrument cluster.

P: Parking, engine starting andkey removal

R: Reverse

N: Neutral

D: Normal driving (with overdrive on)

M: “M” position

2: Stronger engine braking

L: Maximum engine braking

�2ZZ−GE engine

Lock release buttonTo prevent misshifting

With the brake pedal depressed,shift while holding the lock releasebutton in. (The ignition switchmust be in “ON” position.)

Shift while holding the lockrelease button in.

Overdrive switch

Selector lever

Shift normally.To select “M”, lean the selectorlever leftward from “D”.



(b) Overdrive switch

You can select either third gear (withoverdrive off) or fourth gear (with over-drive on) by pushing this switch.

To turn the overdrive off, push the switch.The “O/D OFF” indicator light should comeon. To turn the overdrive on again, pushthe switch again. The “O/D OFF” indicatorlight should go off.

Always drive your vehicle with the over-drive on for better fuel economy andquieter driving.

If the engine is turned off when the over-drive is off and restarted, the overdrivewill automatically be on.

When you are driving in “M” mode, over-drive switch does not activate. (For de-tails, see (d) Driving in M mode and (e)Using engine braking in this section.)



(c) Normal driving

1. Start the engine as instructed in “Howto start the engine” in Section 3. Thetransmission must be in “P” or “N”.

2. With your foot holding down the brakepedal, shift the selector lever to “D”.

When the lever is in the “D” position, theautomatic transmission system will selectthe most suitable gear for running condi-tions such as normal cruising, hill climb-ing, hard towing, etc. The current gearposition is displayed on the instrumentcluster.



Always turn the overdrive on for betterfuel economy and quieter driving. If theengine coolant temperature is low, thetransmission will not shift into the over-drive gear even with the overdrive on.

CAUTION

Never put your foot on the accelera-tor pedal while shifting.

3. Release the parking brake and brakepedal. Depress the accelerator pedalslowly for smooth starting.

(d) Driving in M mode

When the selector lever is into the “M”position, you can select the gear posi-tion manually by pushing the transmis-sion shift switches on the steeringwheel. The M mode indicator light willbe displayed on the instrument cluster.

1: Upshift switch (rear side)2: Downshift switch (front side)

When you push the transmission upshiftswitch on the rear side of the steeringwheel, the transmission upshifts from “1”to “2”, “3” and “4”.

Each time you push the transmissiondownshift switch on the front side of thesteering wheel, the transmission down-shifts from “4” to “3”, “2” and then to “1”.

The current gear position is displayed onthe instrument cluster.

Even if the lever is in the “M” position,the transmission will downshift automati-cally to first gear when you stop the ve-hicle.

You attempt to downshift the transmissionwhen it is not possible to downshift dueto the high vehicle speed. A buzzer willsound when this happens.

You can start from second gear by settingthe shift switch while the vehicle isstopped. This is useful for driving yourvehicle on slippery (rainy, icy or snow−covered) roads.



Recommended shifting speeds

For the best compromise between fueleconomy and vehicle performance, youshould upshift or downshift at approxi-mately the following speeds:

gear km/h (mph)1 to 2 or 2 to 1 24 (15)2 to 3 or 3 to 2 40 (25)3 to 4 or 4 to 3 65 (40)

Downshift to the appropriate gear if accel-eration is needed when you are cruisingbelow the above downshifting speeds.

Upshifting too soon or downshifting toolate will cause lugging, and possibly ping-ing. Regularly revving the engine to maxi-mum speed in each gear will cause ex-cessive engine wear and high fuelconsumption.

NOTICE

Be careful not to over−rev the engine.Watch the tachometer to keep enginerpm from going into the red zone.The approximate maximum allowablespeed for each position is given be-low for your reference:

“2” 125 km/h (77 mph). . . . . . . . . . . . “1” 70 km/h (43 mph). . . . . . . . . . . . .

If the M mode indicator light flashes...

Put the selector lever in the “D” positionand drive for a short time.

If the M mode indicator light stops flash-ing but remains on after the selector leveris returned to the “M” position, you candrive in M mode.

If the M mode indicator light still flashes,there is a problem somewhere in the sys-tem. Put the selector lever in the “D”position. Consult with your Toyota dealeras soon as possible.

The M mode indicator light flashes underthe following conditions:

� The temperature of the automatic trans-mission oil is low. The transmissionworks exactly in the same way aswhen you put the selector lever in the“D” position.

� The temperature of the automatic trans-mission oil is high. You can still oper-ate the transmission shift switches.

� There is a problem somewhere in thesystem.

(e) Using engine braking

To use engine braking, you can downshiftthe transmission as follows:

� When you are driving in the “D” posi-tion, push the overdrive switch. The“O/D OFF” indicator light will come onand the transmission will downshift tothird gear, and engine braking will beobtained. When you are driving infourth gear (“M” position), push thetransmission downshift switch to selectthe “3” position. The transmission willdownshift to third gear and enginebraking will be obtained.

� Shift the selector lever into the “2”position or push the transmission shiftswitch to the “2” position in M mode.The transmission will downshift to sec-ond gear when the vehicle speed dropsdown to or lower than 115 km/h (71mph), and stronger engine braking willbe enabled.

� Shift the selector lever into the “L”position or push the transmission shiftswitch to the “1” position in M mode.The transmission will downshift to firstgear when the vehicle speed dropsdown to or lower than 54 km/h (34mph), and maximum engine braking willbe enabled.





CAUTION


(f) Using the “2” and “L” positions

The “2” and “L” positions are used forstrong engine braking as described pre-viously.

With the selector lever in “2” or “L”, youcan start the vehicle in motion as with thelever in “D”.

With the selector lever in “2”, the vehiclewill start in first gear and automaticallyshift to second gear.

With the selector lever in “L”, the trans-mission is engaged in first gear.

NOTICE

� Be careful not to over−rev the en-gine. Watch the tachometer to keepengine rpm from going into the redzone. The approximate maximum al-lowable speed for each position isgiven below for your reference:

“2” 125 km/h (77 mph). . . . . . . . . . . “L” 70 km/h (43 mph). . . . . . . . . . . .

� Do not continue hill climbing orhard towing for a long time in the“2” or “L” position. This may causesevere automatic transmission dam-age from overheating. To preventsuch damage, “D” position shouldbe used in hill climbing or hardtowing.

(g) Backing up


2. With the brake pedal held down withyour foot, shift the selector lever to the“R” position.

NOTICE

Never shift into reverse while the ve-hicle is moving.

(h) Parking


2. Pull the parking brake lever up fully tosecurely apply the parking brake.

3. With the brake pedal pressed down,shift the selector lever to the “P” posi-tion.

CAUTION

Never attempt to move the selectorlever into “P” position under any cir-cumstances while the vehicle is mov-ing. Serious mechanical damage andloss of vehicle control may result.

(i) Good driving practice

� If the transmission repeatedly shifts upand down between third gear and over-drive when climbing a gentle slope, theoverdrive should be turned off. Be sureto turn the switch on immediately after-ward.

� When towing a trailer, in order to main-tain engine braking efficiency, do notuse overdrive.



CAUTION

Always keep your foot on the brakepedal while stopped with the enginerunning. This prevents the vehiclefrom creeping.

NOTICE

Do not hold the vehicle on an up-grade with the accelerator pedal. Itcan cause the transmission to over-heat. Always use the brake pedal orparking brake.

(j) Rocking your vehicle in stuck

CAUTION

If your vehicle becomes stuck insnow, mud, sand, etc., then you mayattempt to rock the vehicle free bymoving it forward and backward. Donot attempt this procedure if peopleor objects are anywhere near the ve-hicle. During the rocking operationthe vehicle may suddenly move for-ward or backward as it becomes un-stuck, causing injury or damage tonearby people or objects.

NOTICE

If you rock your vehicle, observe thefollowing precautions to prevent dam-age to the transmission and otherparts.

� Do not depress the accelerator ped-al while shifting the selector leveror before the transmission is com-pletely shifted to forward or reversegear.

� Do not race the engine and avoidspinning the wheels.

� If your vehicle remains stuck afterrocking the vehicle several times,consider other ways such as tow-ing.

(k) If you cannot shift the selector le-ver out of “P” position

If you cannot shift the selector lever fromthe “P” position even though the brakepedal is depressed, use the shift lockoverride button. For instructions, see “Ifyou cannot shift automatic transmissionselector lever” in Section 4.



5−speed

6−speed

The shift pattern is as shown above.

In case of driving your vehicle with6−speed manual transmission, the buzzerwill sound when you shift the gear into“R” (reverse).

Press the clutch pedal down fully whileshifting, and then release it slowly. Do notrest your foot on the pedal while driving,because it will cause clutch trouble. Anddo not use the clutch to hold the vehiclewhen stopped on an uphill grade—use theparking brake.

Recommended shifting speeds

The transmission is fully synchronized andupshifting or downshifting is easy.

For the best compromise between fueleconomy and vehicle performance, youshould upshift or downshift at the followingspeeds:

5−speedLow altitude

—1219 m (4000 ft.) or lowergear km/h (mph)

1 to 2 or 2 to 1 24 (15)2 to 3 or 3 to 2 37/40∗1 (23/25∗1)3 to 4 or 4 to 3 64/45∗2 (40/28∗2)4 to 5 or 5 to 4 72/64∗2 (45/40∗2)

∗1: Under cold engine conditions. ∗2: For constant−speed cruise or

constant−speed cruise after decelera-tion.

High altitude—Higher than 1219 m (4000 ft.)

Upshiftinggear km/h (mph)

1 to 2 24 (15)2 to 3 40 (25)3 to 4 64 (40)4 to 5 72 (45)

Downshiftinggear km/h (mph)

2 to 1 24 (15)3 to 2 40 (25)4 to 3 64 (40)5 to 4 72 (45)

6−speedgear km/h (mph)

1 to 2 or 2 to 1 24 (15)2 to 3 or 3 to 2 40 (25)3 to 4 or 4 to 3 64 (40)4 to 5 or 5 to 4 72 (45)5 to 6 or 6 to 5 80 (50)

Manual transmission



Downshift to the appropriate gear if accel-eration is needed when you are cruisingbelow the above downshifting speeds.

Upshifting too soon or downshifting toolate will cause lugging, and possibly ping-ing. Regularly revving the engine to maxi-mum speed in each gear will cause ex-cessive engine wear and high fuelconsumption.

Maximum allowable speeds

To get on a highway or to pass slowertraffic, maximum acceleration may be nec-essary. Make sure you observe the follow-ing maximum allowable speeds in eachgear:

5−speedgear km/h (mph)1 56 (35)2 92 (57)3 126 (78)4 171 (106)

6−speedgear km/h (mph)1 60 (37)2 93 (58)3 128 (80)4 163 (101)5 208 (129)

NOTICE

Do not downshift if you are goingfaster than the maximum allowablespeed for the next lower gear.

Good driving practice

� If it is difficult to shift into reverse, putthe transmission in neutral, release theclutch pedal momentarily, and then tryagain.

� When towing a trailer, in order to main-tain engine braking efficiency, do notuse fifth (5−speed models) or sixthgear (6−speed models).

CAUTION


NOTICE

Make sure the vehicle is completelystopped before shifting into reverse.

Type A

Type B

Parking brake



When parking, firmly apply the parkingbrake to avoid inadvertent creeping.

To set: Pull up the lever. For better hold-ing power, first depress the brake pedaland hold it while setting the parkingbrake.To release: Pull up the lever slightly (1),press the lock release button (2), and low-er (3).

To remind you that the parking brake isset, the parking brake reminder light inthe instrument panel remains on until yourelease the parking brake.

CAUTION

Before driving, be sure the parkingbrake is fully released and the park-ing brake reminder light is off.

The cruise control allows you to cruisethe vehicle at a desired speed over 40km/h (25 mph) even with your foot offthe accelerator pedal.

Your cruising speed can be maintained upor down grades within the limits of engineperformance, although a slight speedchange may occur when driving up ordown the grades. On steeper hills, agreater speed change will occur so it isbetter to drive without the cruise control.

CAUTION

� To help maintain maximum controlof your vehicle, do not use thecruise control when driving inheavy or varying traffic, or on slip-pery (rainy, icy or snow−covered) orwinding roads.

� Avoid vehicle speed increases whendriving downhill. If the vehiclespeed is too fast in relation to thecruise control set speed, cancel thecruise control then downshift thetransmission to use engine brakingto slow down.

TURNING ON THE SYSTEM

To operate the cruise control, press the“CRUISE ON−OFF” button. This turns thesystem on. The indicator light in the in-strument panel shows that you can nowset the vehicle at a desired cruisingspeed. Another press will turn the systemcompletely off.

CAUTION

To avoid accidental cruise control en-gagement, keep the “CRUISE ON−OFF” switch off when not using thecruise control.

Cruise control



SETTING AT A DESIRED SPEED

On vehicles with automatic transmission,the selector lever must be in the “D” posi-tion or the gear position must be “3” or“4” in M mode before you set the cruisecontrol speed.

Bring your vehicle to the desired speed,push the lever down in the “SET/COAST”direction and release it. This sets the ve-hicle at that speed. If the speed is notsatisfactory, tap the lever up for a fasterspeed, or tap it down for a slower speed.Each tap changes the set speed by 1.6km/h (1.0 mph). You can now take yourfoot off the accelerator pedal.

If you need acceleration—for example,when passing—depress the acceleratorpedal enough for the vehicle to exceedthe set speed. When you release it, thevehicle will return to the speed set priorto the acceleration.

CAUTION

For manual transmission:

While driving with the cruise controlon, do not shift to neutral withoutdepressing the clutch pedal, as thismay cause engine racing or over−rev-ving.

CANCELLING THE PRESET SPEED

You can cancel the preset speed by:

a. Pulling the lever in the “CANCEL” di-rection and releasing it.

b. Depressing the brake pedal.

c. Depressing the clutch pedal (manualtransmission).

If the vehicle speed falls below about 40km/h (25 mph), the preset speed will auto-matically cancel out.

If the vehicle speed drops 16 km/h (10mph) below the preset speed, the presetspeed will also automatically cancel out.

If the preset speed automatically cancelsout other than for the above cases, haveyour vehicle checked by your Toyota deal-er at the earliest opportunity.

RESETTING TO A FASTER SPEED

Push the lever up in the “RES/ACC” direc-tion and hold it. Release the lever whenthe desired speed is attained. While thelever is held up, the vehicle will graduallygain speed.

However, a faster way to reset is to ac-celerate the vehicle and then push thelever down in the “SET/COAST” direction.

RESETTING TO A SLOWER SPEED

Push the lever down in the “SET/COAST”direction and hold it. Release the leverwhen the desired speed is attained. Whilethe lever is held down, the vehicle speedwill gradually decrease.

However, a faster way to reset is to de-press the brake pedal and then push thelever down in the “SET/COAST” direction.



On vehicles with automatic transmission,even if you turn off the overdrive switchwith the cruise control on, engine brakingwill not be applied because the cruisecontrol is not cancelled. To decrease thevehicle speed, reset to a slower speedwith the cruise control lever or depressthe brake pedal. If you use the brakepedal, cruise control is cancelled.

RESUMING THE PRESET SPEED

If the preset speed is cancelled by pullingthe control lever or by depressing thebrake pedal or clutch pedal, pushing thelever up in the “RES/ACC” direction willrestore the speed set prior to cancellation.

However, once the vehicle speed falls be-low about 40 km/h (25 mph), the presetspeed will not be resumed.

CRUISE CONTROL FAILURE WARNING

If the “CRUISE” indicator light in the in-strument cluster flashes when using thecruise control, press the “CRUISE ON−OFF” button to turn the system off andthen press it again to turn it on.

If any of the following conditions then oc-curs, there is some trouble in the cruisecontrol system.

� The indicator light does not come on.

� The indicator light flashes again.

� The indicator light goes out after itcomes on.

If this is the case, contact your Toyotadealer and have your vehicle inspected.





OPERATION OF INSTRUMENTS ANDCONTROLSCar audio system

Reference 100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Using your audio system 100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Car audio system operating hints 108. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 7


100 2002 MY CELICA_U (OM20792U)

AM·FM ETR radio/cassette player/compactdisc player (with compact disc autochanger controller)

This section describes some of the basicfeatures on Toyota audio systems. Someinformation may not pertain to your sys-tem.

Your audio system works when the ignitionkey is in the “ACC” or “ON” position.

TURNING THE SYSTEM ON AND OFF

Push “PWR·VOL” to turn the audio systemon and off.

Push “AM”, “FM1·2”, “TAPE” or “CD” toturn on that function without pushing“PWR·VOL”.

You can turn on each player by insertinga cassette tape or compact disc.

You can turn off each player by ejectingthe cassette tape or compact disc. If theaudio system was previously off, then theentire audio system will be turned offwhen you eject the cassette tape or com-pact disc. If another function was pre-viously playing, it will come on again.

SWITCHING BETWEEN FUNCTIONS

Push “AM”, “FM1·2”, “TAPE” or “CD” if thesystem is already on but you want toswitch from one function to another.

TONE AND BALANCE

For details about your system’s tone andbalance controls, see the description ofyour own system.

Tone

How good an audio program sounds toyou is largely determined by the mix ofthe treble, midrange, and bass levels. Infact, different kinds of music and vocalprograms usually sound better with differ-ent mixes of treble, midrange and bass.

Balance

A good balance of the left and right stereochannels and of the front and rear soundlevels is also important.

Keep in mind that if you are listening toa stereo recording or broadcast, changingthe right/left balance will increase the vol-ume of one group of sounds while de-creasing the volume of another.

ReferenceUsing your audio system——Some basics



YOUR RADIO ANTENNA

To remove the antenna, carefully turn itcounterclockwise.

NOTICE

To prevent damage to the antenna,make sure it is removed before driv-ing your Toyota through an automaticcar wash.

On−glass antenna (built−in on the rearwindow glass)

NOTICE

Attaching film (especially conductiveor metallic type) on the rear glasswill noticeably reduce the sensitivityof the radio.

YOUR CASSETTE PLAYER

When you insert a cassette, the exposedtape should be to the right.

NOTICE

Do not oil any part of the player anddo not insert anything other than cas-sette tapes into the slot, or the tapeplayer may be damaged.

YOUR COMPACT DISC PLAYER

When you insert a disc, gently push it inwith the label side up. (The player willautomatically eject a disc if the label sideis down.) The compact disc player willplay from track 1 through the end of thedisc. Then it will play from track 1 again.On models with the compact disc autochanger, next disc will be played fromtrack 1.

NOTICE

Never try to disassemble or oil anypart of the compact disc player. Donot insert anything except a compactdisc into the slot.

The player is intended for use with 12 cm(4.7 in.) discs only.


102 2002 MY CELICA_U (OM20792U)

Details of specific buttons, controls, andfeatures are described in the alphabeticallisting that follows.

—Controls and features



1 2 3 4 5 6 (Preset buttons)

These buttons are used to preset andtune in radio stations.

To preset a station to a button: Tune inthe desired station (see “TUNE” knob or“SEEK” button). Push and hold down thebutton until you hear a beep—this will setthe station to the button. The button num-ber will appear on the display.

To tune in to a preset station: Push thebutton for the station you want. The but-ton number and station frequency will ap-pear on the display.

These systems can store one AM and twoFM stations for each button (The displaywill show “AM”, “FM1” or “FM2” when youpush “AM” “FM1·2”).

(Eject button)

Push the cassette tape eject button toeject a cassette. Push the compact disceject button to eject a compact disc.

After you turn the ignition to “LOCK”, youwill be able to eject a cassette or disc butyou will not be able to reinsert it.

(Program)

Push “ ” to select the other side of acassette tape. The display indicates whichside is currently selected (“ ” indicates

top side, “ ” indicates bottom side).

Auto−reverse feature: After the cassetteplayer reaches the end of a tape side, itautomatically reverses and begins to playthe other side. This is true whether thecassette was playing or fast forwarding.

(Reverse/Fast forward buttons)

Cassette Player

Push the fast forward button to fast for-ward a cassette tape. “FF” will appear onthe display. Push the reverse button torewind a tape. “REW” will appear on thedisplay.

To stop the tape while it is fast forward-ing, push the fast forward button or“TAPE”; to stop the tape while it is re-winding, push the reverse button or“TAPE”.

If a tape side rewinds completely, the cas-sette player will stop and then play thatsame side. If a tape fast forwards com-pletely, the cassette player will play theother side of the tape, using the auto−re-verse feature.

Compact Disc Player

If you want to fast forward or reversethrough a compact disc track, push andhold in the fast forward or reverse button.When you release the button, the compactdisc player will resume playing.

AM

Push “AM” to turn on the radio and selectthe AM band. “AM” will appear on thedisplay.

If the audio system is off, you can turnon the radio by pushing “AM”. Also, push“AM” to switch from cassette or compactdisc operation to radio operation.


104 2002 MY CELICA_U (OM20792U)

CONTROL / MODE (Audio control andmode adjustment)

Manual tone adjustment function—

This knob is used to adjust the tonemanually.

For low−pitch tone adjustment, push“CONTROL / MODE” repeatedly until“BAS” appears on the display. Then turnthe knob to suit your preference.

The display will show the range from“BAS −5” to “BAS 5”.

Vehicles with 8 speakers only—for middle−pitch tone adjustment, push “CONTROL /MODE” repeatedly until “MId” appears onthe display. Then turn the knob to suityour preference.

The display will show the range from “MId−5” to “MId 5”.

For high−pitch tone adjustment, push“CONTROL / MODE” repeatedly until“TRE” appears on the display. Then turnthe knob to suit your preference.

The display will show the range from“TRE −5” to “TRE 5”.

Sound balance adjustment function—

This knob is also used to adjust thesound balance between the front and rear,and the right and left speakers.

For front/rear adjustment, push “CONTROL/ MODE” repeatedly until “FAd” appearson the display. Then turn the knob toadjust the front/rear balance.

The display will show the range from“FAd−F7” to “FAd−R7”.

For left/right adjustment, push “CONTROL/ MODE” repeatedly until “BAL” appearson the display. Then turn the knob toadjust the left/right balance.

The display will show the range from“BAL−L7” to “BAL−R7”.

CD (Compact Disc)

Push “CD” to switch from radio or cas-sette operation to compact disc operation.If the audio system is off, you can turnon the compact disc player by pushing“CD”. In both cases, a disc must alreadybe loaded in the player.

When the audio is set into compact discoperation, the display shows the track or,track and disc number currently beingplayed. Each time you push “CD”, thesystem changes to the automatic changer.

If the player malfunctions, your audio sys-tem will display one of the six followingerror messages.

If “WAIT” appears on the display, it indi-cates that the inside of the player unitmay be too hot due to the very high ambi-ent temperature. Remove the disc or mag-azine from the player and allow the playerto cool down.

If “Err 1” appears on the display, itindicates the disc is dirty, damaged, or itwas inserted up−side down. Clean thedisc or insert it correctly.

If “Err 2” appears on the display, itindicates no disc is loaded inside themagazine. Insert a disc.

If “Err 3” or “Err 4” appears on thedisplay, it indicates there is a trouble in-side the system. Eject the disc or maga-zine. Set the disc or magazine again.

If “OPEn” appears on the display, itindicates the compact disc auto changerlid is open. Close the compact disc autochanger lid.

If the malfunction is not rectified, takeyour vehicle to your Toyota dealer.



DISC ��

Compact disc auto changer only—

By using this button, you can select adisc you wish to listen to.

Push either side of the button until thenumber of the disc you want to listen toappears on the display.

Dolby� B NR∗

If you are listening to a tape that wasrecorded with Dolby� B Noise Reduction,push the button marked with the double−Dsymbol. The double−D symbol will appearon the display. Push the button again toturn off Dolby� B NR.

The Dolby NR mode reduces tape noiseby about 10 dB. For best sound reproduc-tion, play your tapes with this button onor off according to the mode used forrecording the tape.∗: Dolby noise reduction manufactured under license fromDolby Laboratories Licensing Corporation. “DOLBY” and thedouble D symbol are trademarks of Dolby LaboratoriesLicensing Corporation.

FM1·2

Push “FM1·2” to turn on the radio andselect the FM band. “FM1” or “FM2” willappear on the display. This system allowsyou to set twelve FM stations, two foreach button.

If the audio system is off, you can turnon the radio by pushing “FM1·2”. Also,push “FM1·2” to switch from cassette orcompact disc operation to radio operation.

PWR·VOL (Power and Volume)

Push “PWR·VOL” to turn the audio systemon and off. Turn “PWR·VOL” to adjust thevolume.

RAND (Random)

There are two random features—you caneither listen to the tracks on all the com-pact discs in the magazine in random or-der, or only listen to the tracks on aspecific compact disc in random order.

To randomly play the tracks on a disc:Quickly push and release “ ”. “ ”will appear on the display. The disc youare listening to will play in random order.If you hear a beep, you held the buttontoo long, and the player will play all thetracks in the magazine in random order.To turn off the random feature, push thisbutton again.


To randomly play the tracks in the maga-zine:Push and hold “ ” until you hear a

beep. “ ” will appear on the dis-play and the player will perform all thetracks on all the discs in the magazine inrandom order. To turn off the random fea-ture, push this button again.

RPT (Repeat)

Cassette Player

Push “ ” while the track is playing.“ ” will appear on the display. Whenthe track ends, it will automatically berewound and replayed. This process willbe continued until you push the buttonagain to turn off the repeat feature.

There must be at least 3 seconds of blankspace between tracks in order for the re-peat feature to work correctly.


106 2002 MY CELICA_U (OM20792U)

Compact Disc Player

There are two repeat features—You caneither replay a disc track or a whole com-pact disc.

Repeating a track:Quickly push and release “ ” while thetrack is playing. “ ” will appear on thedisplay. If you hear a beep, you held thebutton too long, and the player will repeatthe whole disc. When the track ends, itwill automatically be replayed. This pro-cess will be continued until you push thebutton again to turn off the repeat feature.


Repeating a disc:Push and hold “ ” until you hear a

beep. “ ” will appear on the display.The player will repeat all the tracks on thedisc you are listening to. When the discends, the player will automatically go backto the top track of the disc and replay.This process will be continued until youpush the button again to turn off the re-peat feature.

SCAN

Radio

You can either scan all the frequencies ona band or scan only the preset stationsfor that band.

To scan the preset stations: Push and hold “SCAN” until you hear abeep. The radio will tune in the next pres-et station up the band, stay there for 5seconds, and then move to the next pre-set station. To select a station, push“SCAN” again.

To scan all the frequencies: Quickly push and release “SCAN”. If youhear a beep, you held the button too long,and the radio will scan the preset sta-tions. The radio will find the next stationup the station band, stay there for 5 se-conds, and then scan again. To select astation, push “SCAN” again.

Compact disc player

There are two scan features—you can ei-ther scan the tracks on a specific disc orscan the first tracks of all the discs in themagazine.

Scanning the tracks on a disc:Quickly push and release “SCAN”. “SCAN”will appear on the display and the playerwill scan all the tracks on the disc youare listening to. If you hear a beep, youheld the button too long, and the playerwill scan the first track of all the discs inthe magazine. To select a track, push“SCAN” again. If the player scanned allthe tracks on the disc, it will stop scan-ning.


Scanning the first track of all the discs inthe magazine:Push “SCAN” until you hear a beep.

“ ·SCAN” will appear on the display

and the player will perform the first trackof the next disc. To select a disc, pushthe “SCAN” again. If the player hasscanned all the discs, it will stop scan-ning.



SEEK (Seeking)

Radio

In the seek mode, the radio finds andplays the next station up or down thestation band.

To seek a station, quickly push and re-lease the “�” or “�” under the “SEEK”.Do this again to find another station.

Cassette Player

By using this button, you can skip up ordown to a different track.

You can skip up to nine tracks at a time.

Push the up or down side of the button.“FF 1” or “REW 1” will appear on thedisplay.

Next, push either side of the track buttonuntil the number on the display reachesthe number of tracks you want to skip. Ifyou push the button ten times, the skipfeature will be turned off.

When counting the number of tracks youwant to rewind, remember to count thecurrent track as well. For example, if youwant to rewind to a song that is two be-fore the song you are listening to, pushon the down side of the button until “REW3” appears on the display.

If you have pushed the track button morethan you wanted to, push the other sideof the button. The track number will bereduced.

The track number you select is not validif it is higher than the number of tracksremaining on the current cassette side.

� After the beginning of the tape isreached, the player will automaticallystart playing the same side.

� After the end of the tape is reached,the player will automatically reversesides and start playing the other side.

There must be at least 3 seconds of blankspace between tracks for the track buttonto work correctly. In addition, the featuremay not work well with some spokenword, live, or classical recordings.

ST (Stereo reception) display

Your radio automatically changes to stereoreception when a stereo broadcast is re-ceived. “ST” appears on the display. If thesignal becomes weak, the radio reducesthe amount of channel separation to prev-ent the weak signal from creating noise.If the signal becomes extremely weak, theradio switches from stereo to mono recep-tion.

TAPE

Push “TAPE” to switch from radio or com-pact disc operation to cassette operation.If the audio system is off, you can turnon the cassette player by pushing “TAPE”.In both cases, a cassette must already beloaded in the player.

TRACK (Track up/down button): Compact disc player

By using this button, you can skip up ordown to a different track.

Push either side of the track button untilthe number of the track you want to listento appears on the display. If you want toreturn to the beginning of the currenttrack, push the down side of the buttonone time, quickly.

TUNE (Tuning)

Your Toyota has an electronic tuning radio(ETR). Turn the knob clockwise to step upthe frequency. Turn the knob counterclock-wise to step down the frequency.


108 2002 MY CELICA_U (OM20792U)

NOTICE

To ensure the correct audio systemoperation:

� Be careful not to spill beveragesover the audio system.

� Do not put anything other than acassette tape or Compact Disc intothe slot.

� The use of cellular phone inside ornear the vehicle may cause a noisefrom the speakers of the audio sys-tem which you are listening to.However, this does not indicate amalfunction.

RADIO RECEPTION

Usually, a problem with radio receptiondoes not mean there is a problem withyour radio—it is just the normal result ofconditions outside the vehicle.

For example, nearby buildings and terraincan interfere with FM reception. Powerlines or telephone wires can interfere withAM signals. And of course, radio signalshave a limited range. The farther you arefrom a station, the weaker its signal willbe. In addition, reception conditionschange constantly as your vehicle moves.

Here are some common reception prob-lems that probably do not indicate a prob-lem with your radio:

FM

Fading and drifting stations—Generally, theeffective range of FM is about 40 km (25miles). Once outside this range, you maynotice fading and drifting, which increasewith the distance from the radio transmit-ter. They are often accompanied by distor-tion.

Multi−path—FM signals are reflective,making it possible for two signals to reachyour antenna at the same time. If thishappens, the signals will cancel each oth-er out, causing a momentary flutter orloss of reception.

Static and fluttering—These occur whensignals are blocked by buildings, trees, orother large objects. Increasing the basslevel may reduce static and fluttering.

Station swapping—If the FM signal youare listening to is interrupted or weak-ened, and there is another strong stationnearby on the FM band, your radio maytune in the second station until the origi-nal signal can be picked up again.

AM

Fading—AM broadcasts are reflected bythe upper atmosphere—especially at night.These reflected signals can interfere withthose received directly from the radio sta-tion, causing the radio station to soundalternately strong and weak.

Station interference—When a reflected sig-nal and a signal received directly from aradio station are very nearly the samefrequency, they can interfere with eachother, making it difficult to hear the broad-cast.

Static—AM is easily affected by externalsources of electrical noise, such as hightension power lines, lightening, or electri-cal motors. This results in static.

CARING FOR YOUR CASSETTE PLAYERAND TAPES

For the best performance for your cas-sette player and tapes:

Clean the tape head and other parts regu-larly.

� A dirty tape head or tape path candecrease sound quality and tangle yourcassette tapes. The easiest way toclean them is by using a cleaning tape.(A wet type is recommended.)

Car audio system operatinghints



Use high−quality cassettes.

� Low−quality cassette tapes can causemany problems, including poor sound,inconsistent playing speed, andconstant auto−reversing. They can alsoget stuck or tangled in the cassetteplayer.

� Do not use a cassette if it has beendamaged or tangled or if its label ispeeling off.

� Do not leave a cassette in the playerif you are not listening to it, especiallyif it is hot outside.

� Store cassettes in their cases and outof direct sunlight.

� Avoid using cassettes with a total play-ing time longer than 100 minutes (50minutes per side). The tape used inthese cassettes is thin and could getstuck or tangled in the cassette player.

CARING FOR YOUR COMPACT DISCPLAYER AND DISCS

� Use only compact discs labeled asshown above. CD−R (CD−Recordable),CD−RW (CD−Re−writable) and personalcomputer use CD−ROMs may not beplayable on your compact disc player.

� Your compact disc player is intendedfor use with 12 cm (4.7 in.) discs only.

� Extremely high temperatures can keepyour compact disc player from working.On hot days, use the air conditioningto cool the vehicle interior before youlisten to a disc.

� Bumpy roads or other vibrations maymake your compact disc player skip.

� If moisture gets into your compact discplayer, you may not hear any soundeven though your compact disc playerappears to be working. Remove thedisc from the player and wait until itdries.


110 2002 MY CELICA_U (OM20792U)

� Your compact disc player cannot playspecial shaped or low−quality compactdiscs such as those shown here. Donot use them as the player could bedamaged.

� Handle compact discs carefully, espe-cially when you are inserting them.Hold them on the edge and do notbend them. Avoid getting fingerprintson them, particularly on the shiny side.

� Dirt, scrapes, warping, pin holes, orother disc damage could cause theplayer to skip or to repeat a section ofa track. (To see a pin hole, hold thedisc up to the light.)

� Remove discs from the compact discplayer when you are not listening tothem. Store them in their plastic casesaway from moisture, heat, and directsunlight.

To clean a compact disc: Wipe it with asoft, lint−free cloth that has been damp-ened with water. Wipe in a straight linefrom the center to the edge of the disc(not in circles). Dry it with another soft,lint−free cloth. Do not use a conventionalrecord cleaner or anti−static device.

CAUTION

Compact disc players use an invisiblelaser beam which could cause hazard-ous radiation exposure if directedoutside the unit. Be sure to operatethe player correctly.



OPERATION OF INSTRUMENTS ANDCONTROLSAir conditioning system

Controls 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Air flow selector settings 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating tips 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Instrument panel vents 117. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 8


112 2002 MY CELICA_U (OM20792U)

1. Temperature selector

2. Air intake selector

3. Air flow selector

4. “A/C” button (on some models)

5. Fan speed selector

Controls



Fan speed selector

Turn the knob to adjust the fan speed—tothe right to increase, to the left to de-crease.

Temperature selector

Turn the knob to adjust the tempera-ture—to the right to warm, to the left tocool.

Air flow selector

Turn the knob to select the vents used forair flow.

1. Panel—Air flows mainly from the in-strument panel vents.

2. Bi−level—Air flows from both the floorvents and the instrument panel vents.

3. Floor—Air flows mainly from the floorvents.

4. Floor/Windshield—Air flows mainlyfrom the floor vents and windshieldvents.

Use with the air intake selector posi-tioned in Fresh.

5. Windshield—Air flows mainly from thewindshield vents.

Turning the air flow selector to thewindshield position turns on the defog-ging function with the purpose of clear-ing the front view.

Use with the air intake selector posi-tioned in Fresh.

Vehicles with “A/C” button—

Press the “A/C” button for dehumidifiedheating or cooling. This setting clears thefront view more quickly.

For details about air flow selector settings,see the illustration after “A/C” button.


114 2002 MY CELICA_U (OM20792U)

Air intake selector

Move the lever to select the air source.

1. Recirculate—Recirculates the air insidethe vehicle.

2. Fresh—Draws outside air into the sys-tem.

“A/C” button (on some models)

To turn on the air conditioning, press the“A/C” button. The “A/C” button indicatorwill come on. To turn the air conditioningoff, press the button again.

If the “A/C” button indicator flashes, thereis a problem in the air conditioning systemand the air conditioning automaticallyshuts off. If this happens, take your ve-hicle to a Toyota dealer for service.



� To cool off your Toyota after it hasbeen parked in the hot sun, drive withthe windows open for a few minutes.This vents the hot air, allowing the airconditioning to cool the interior morequickly.

� Make sure the air intake grilles in frontof the windshield are not blocked (byleaves or snow, for example).

� On humid days, do not blow cold airon the windshield. The windshield couldfog up because of the difference in airtemperature on the inside and outsideof the windshield.

� Keep the area under the front seatsclear to allow air to circulate through-out the vehicle.

� On cold days, set the fan speed tohigh for a minute to help clear theintake ducts of snow or moisture. Thiscan reduce the amount of fogging onthe windows.

� When driving on dusty roads, close allwindows. If dust thrown up by the ve-hicle is still drawn into the vehicle afterclosing the windows, it is recommendedthat the air intake selector be set toFRESH and the fan speed selector toany setting except “OFF”.

Air flow selector settings Operating tips


116 2002 MY CELICA_U (OM20792U)

� If following another vehicle on a dustyroad, or driving in windy and dustyconditions, it is recommended that theair intake selector be temporarily set toRECIRCULATE, which will close off theoutside passage and prevent outsideair and dust from entering the vehicleinterior.

Heating

For best results, set controls to:

Fan speed—Any setting except “OFF”Temperature—Towards WARM

(red zone)Air intake—FRESH (outside air)Air flow—FLOORAir conditioning—OFF

� For quick heating, select recirculatedair for a few minutes. To keep thewindows from fogging. select fresh af-ter the vehicle interior has beenwarmed.

� Press the “A/C” button on for dehumidi-fied heating.

� Choose floor/windshield air flow to heatthe vehicle interior while defrosting ordefogging the windshield.

Air conditioning


Fan speed—Any setting except “OFF”Temperature—Towards COLD

(blue zone)Air intake—FRESH (outside air)Air flow—PANELAir conditioning—ON

� For quick cooling, move the air intakeselector to recirculate for a few min-utes.

Ventilation


Fan speed—Any setting except “OFF”Temperature—Towards COLD

(blue zone)Air intake—FRESH (outside air)Air flow—PANELAir conditioning—OFF



Defogging and defrosting

The inside of the windshield



(red zone) to heat;COLD (blue zone) cool

Air intake—FRESH (outside air)Air flow—WINDSHIELD

Turning the air flow selector to the wind-shield position turns on the defoggingfunction with the purpose of clearing thefront view.



� On humid days, do not blow cold airon the windshield—the difference be-tween the outside and inside tempera-tures could make the fogging worse.

The outside of the windshield



(red zone)Air intake—FRESH (outside air)Air flow—WINDSHIELD

Turning the air flow selector to the wind-shield position turns on the defoggingfunction with the purpose of clearing thefront view.



� To heat the vehicle interior while de-frosting the windshield, choose floor/windshield air flow.

Open

Close

If air flow control is not satisfactory, checkthe instrument panel vents. The instrumentpanel vents may be opened or closed asshown.

Instrument panel vents


118 2002 MY CELICA_U (OM20792U)

You can change air flow direction by turn-ing the instrument panel vents.



OPERATION OF INSTRUMENTS ANDCONTROLSOther equipmentClock 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cigarette lighter and ashtray 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glove box 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary boxess 121. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cup holders 122. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tie−down hooks 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Luggage cover 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grocery bag hooks 123. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Floor mat 124. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 1− 9


120 2002 MY CELICA_U (OM20792U)

The digital clock indicates the time.

The key must be in the “ACC” or “ON”position.

To reset the hour: Push the “H” button.To reset the minutes: Push the “M” button.

If quick adjustment to a full hour is de-sired, push the “:00” button.

For example, if the “:00” button is de-pressed when the time is between1:01—1:29, the time will change to 1:00.If the time is between 1:30—1:59, thetime will change to 2:00.

If the electrical power source has beendisconnected from the clock, the time dis-play will automatically be set to 1:00 (oneo’clock).

When the instrument panel lights areturned on, the brightness of the time indi-cation will be reduced.

CIGARETTE LIGHTER

To use the cigarette lighter, press it in.When it becomes heated, it automatical-ly pops out ready for use.

If the engine is not running, the key mustbe in the “ACC” position.

Do not hold the cigarette lighter pressedin.

Use a Toyota genuine cigarette lighter orequivalent for replacement.

Clock Cigarette lighter and ashtray



ASHTRAY

To use the ashtray, pull out the lid.

When finished with your cigarette, thor-oughly extinguish it in the ashtray to pre-vent other cigarette butts from catchingfire. After using the ashtray, close the lidcompletely.

To remove the ashtray, pull the lid andpull it out.

CAUTION

To reduce the chance of injury incase of an accident or sudden stopwhile driving, always close the lidcompletely after using.

To use the glove box, do this.

To open: Pull the lever.

With the instrument panel lights on, theglove box light will come on when theglove box is open.

To lock: Insert the master key and turn itclockwise.

CAUTION

To reduce the chance of injury incase of an accident or a sudden stop,always keep the glove box doorclosed while driving.

Instrument panel

Rear console

Glove box Auxiliary boxes


122 2002 MY CELICA_U (OM20792U)

To use the boxes, open them as shownin the illustrations.

CAUTION

To reduce the chance of injury incase of an accident or a sudden stop,always keep the auxiliary box closedwhile driving.

Front

Rear

The cup holders are designed for hold-ing cups or drink−cans securely.

CAUTION

Do not place anything else other thancups or drink−cans in the cup holder,as such items may be thrown aboutin the compartment and possibly in-jure people in the vehicle during sud-den braking or in an accident.

Cup holders



To secure your luggage, use the tie−down hooks as shown above.

See “Luggage stowage precautions” inSection 2 for precautions in loading lug-gage.

CAUTION

To avoid personal injury, keep the tie−down hooks stored under the carpetwhen not in use.

When you open the back door, the lug-gage cover tilt ups for easy access tothe luggage compartment.

For additional luggage space, unhook thecords and lift the cover out of the retain-ers.

Make sure the luggage cover is surelystowed when reinstalling it.

These hooks are designed to hangthings like grocery bags.

NOTICE

To prevent damage to the hook, avoidhanging heavy loads on it.

Tie−down hooks Luggage cover Grocery bag hooks


124 2002 MY CELICA_U (OM20792U)

Use a floor mat of the correct size.

If the floor carpet and floor mat have ahole, then it is designed for use with alocking clip. Fix the floor mat with lockingclip into the hole in the floor carpet.

CAUTION

Make sure the floor mat is properlyplaced on the floor carpet. If the floormat slips and interferes with themovement of the pedals during driv-ing, it may cause an accident.

Floor mat



INFORMATION BEFORE DRIVING YOURTOYOTABreak−in periodod 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel pump shut off system 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation in foreign countries 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Three−way catalytic converter 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine exhaust cautions 129. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Facts about engine oil consumption 130. . . . . . . . . . . . . . . . . . . . . . . . . . Iridium−tipped spark plugs 131. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brake system 131. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brake pad wear limit indicators 134. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Luggage stowage precautions 135. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Your Toyota’s identification 135. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Theft prevention labels 137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Suspension and chassis 137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Types of tires 137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 2


126 2002 MY CELICA_U (OM20792U)

Drive gently and avoid high speeds.

Your vehicle does not need an elaboratebreak−in. But following a few simple tipsfor the first 1600 km (1000 miles) can addto the future economy and long life ofyour vehicle:

� Do not drive over 88 km/h (55 mph).

� Run the engine at moderate speed be-tween 2000 and 4000 rpm.

� Avoid full−throttle starts.

� Try to avoid hard stops during the first300 km (200 miles).

� Do not drive slowly with the transmis-sion in a high gear.

� Do not drive for a long time at anysingle speed, either fast or slow.

� Do not tow a trailer during the first 800km (500 miles).

FUEL TYPE

Your new vehicle must use onlyunleaded gasoline.

To help prevent gas station mix−ups, yourToyota has a smaller fuel tank opening.The special nozzle on pumps with un-leaded fuel will fit it, but the larger stan-dard nozzle on pumps with leaded gas willnot.

At a minimum, the gasoline you useshould meet the specifications of ASTMD4814 in the U.S.A. and CGSB 3.5−M93in Canada.

NOTICE

Do not use leaded gasoline. Use ofleaded gasoline will cause the three−way catalytic converter to lose its ef-fectiveness and the emission controlsystem to function improperly. Also,this can increase maintenance costs.

OCTANE RATING

1ZZ−FE engine—Select Octane Rating 87 (Research Oc-tane Number 91) or higher.

2ZZ−GE engine—Select premium unleaded gasoline withan Octane Rating of 91 (Research Oc-tane Number 96) or higher for optimumengine performance.

Use of unleaded gasoline with an octanerating or research octane number lowerthan stated above will cause persistentheavy knocking. If it is severe, this willlead to engine damage.

If your engine knocks...

If you detect heavy knocking even whenusing the recommended fuel, or if youhear steady knocking while holding asteady speed on level roads, consult yourToyota dealer.

However, now and then, you may noticelight knocking for a short time while accel-erating or driving up hills. This is no needof concern.

GASOLINE CONTAINING DETERGENTADDITIVES

Toyota recommends the use of gasolinethat contains detergent additives toavoid build−up of engine deposits.

However, all gasoline sold in the U.S.contains detergent additives to keep cleanand/or clean intake systems.

Break−in period Fuel



QUALITY GASOLINE

Automotive manufacturers in the U.S.,Europe and Japan have developed aspecification for quality fuel namedWorld−Wide Fuel Charter (WWFC) thatis expected to be applied world wide.The WWFC consists of three categoriesthat depend on required emission lev-els. In the U.S., category 3 has beenadopted. The WWFC improves air quali-ty by providing for better emissions invehicle fleets, and customer satisfactionthrough better vehicle performance.

CLEANER BURNING GASOLINE

Cleaner burning gasoline, including re-formulated gasoline that contains oxy-genates such as ethanol or MTBE isavailable in many areas.

Toyota recommends the use of cleanerburning gasoline and appropriately blendedreformulated gasoline. These types of gas-oline provide excellent vehicle perfor-mance, reduce vehicle emissions, and im-prove air quality.

OXYGENATES IN GASOLINE

Toyota allows the use of oxygenateblended gasoline where the oxygenatecontent is up to 10% ethanol or 15%MTBE. If you use gasohol in yourToyota, be sure that it has an octanerating no lower than 87.

Toyota does not recommend the use ofgasoline containing methanol.

GASOLINE CONTAINING MMT

Some gasoline contain an octane en-hancing additive called MMT (Methylcy-clopentadienyl Manganese Tricarbonyl).

Toyota does not recommend the use ofgasoline that contains MMT. If fuel con-taining MMT is used, your emission con-trol system may be adversely affected.The Malfunction Indicator Lamp on the in-strument cluster may come on. If this hap-pens, contact your Toyota dealer for ser-vice.

GASOLINE QUALITY

In a very few cases, you may experiencedriveability problems caused by the partic-ular gasoline that you are using. If youcontinue to have unacceptable driveability,try changing gasoline brands. If this doesnot rectify your problem, then consult yourToyota dealer.

NOTICE

� Do not use gasohol other thanstated above. It will cause fuel sys-tem damage or vehicle performanceproblems.

� If driveability problems occur (poorhot starting, vaporizing, engineknock, etc.), discontinue the use.

� Take care not to spill gasohol dur-ing refueling. Gasohol may causepaint damage.

FUEL TANK CAPACITY

55 L (14.5 gal., 12.1 Imp. gal.)


128 2002 MY CELICA_U (OM20792U)

The fuel pump shut off system stops sup-plying fuel to the engine to minimize therisk of fuel leakage when the engine stallsor an airbag inflates upon collision. Torestart the engine after the fuel pump shutoff system activates, turn the ignitionswitch to “ACC” or “LOCK” once and startit.

CAUTION

Inspect the ground under the vehiclebefore restarting the engine. If youfind that liquid has leaked onto theground, it is the fuel system hasbeen damaged and it is in need ofrepair. In this case, do not restart theengine.

If you plan to drive your Toyota inanother country...

First, comply with the vehicle registrationlaws.

Second, confirm the availability of the cor-rect fuel (unleaded and minimum octanenumber).

The three−way catalytic converter is anemission control device installed in theexhaust system.

The purpose is to reduce pollutants in theexhaust gas.

CAUTION

� Keep people and combustible mate-rials away from the exhaust pipewhile the engine is running. Theexhaust gas is very hot.

� Do not drive, idle or park your ve-hicle over anything that might burneasily such as grass, leaves, paperor rags.

Fuel pump shut off system Operation in foreign countries Three−way catalytic converter



NOTICE

A large amount of unburned gasesflowing into the three−way catalyticconverter may cause it to overheatand create a fire hazard. To preventthis and other damage, observe thefollowing precautions:

� Use only unleaded gasoline.

� Do not drive with an extremely lowfuel level; running out of fuel couldcause the engine to misfire, creat-ing an excessive load on the three−way catalytic converter.

� Do not allow the engine to run atidle speed for more than 20 min-utes.

� Avoid racing the engine.

� Do not push−start or pull−start yourvehicle.

� Do not turn off the ignition whilethe vehicle is moving.

� Keep your engine in good runningorder. Malfunctions in the engineelectrical system, electronic ignitionsystem/distributor ignition systemor fuel system could cause an ex-tremely high three−way catalyticconverter temperature.

� If the engine becomes difficult tostart or stalls frequently, take yourvehicle in for a check−up as pos-sible. Remember, your Toyota dealerknows your vehicle and its three−way catalytic converter system best.

� To ensure that the three−way cata-lytic converter and the entire emis-sion control system operate proper-ly, your vehicle must receive theperiodic inspections required by theToyota Maintenance Schedule. Forscheduled maintenance information,refer to the “Scheduled MaintenanceGuide” or “Owner’s Manual Supple-ment”.

CAUTION

� Avoid inhaling the engine exhaust.It contains carbon monoxide, whichis a colorless and odorless gas. Itcan cause unconsciousness or evendeath.

� Make sure the exhaust system hasno holes or loose connections. Thesystem should be checked fromtime to time. If you hit something,or notice a change in the sound ofthe exhaust, have the systemchecked immediately.

� Do not run the engine in a garageor enclosed area except for thetime needed to drive the vehicle inor out. The exhaust gases cannotescape, making this a particularlydangerous situation.

� Do not remain for a long time in aparked vehicle with the engine run-ning. If it is unavoidable, however,do so only in an unconfined areaand adjust the heating or coolingsystem to force outside air into thevehicle.

Engine exhaust cautions


130 2002 MY CELICA_U (OM20792U)

� Keep the back door closed whiledriving. An open or unsealed backdoor may cause exhaust gases tobe drawn into the vehicle.

� To allow proper operation of yourvehicle’s ventilation system, keepthe inlet grilles in front of the wind-shield clear of snow, leaves, or oth-er obstructions.

� If you smell exhaust fumes in thevehicle, drive with the windowsopen and the back door closed.Have the cause immediately locatedand corrected.

FUNCTIONS OF ENGINE OIL

Engine oil has the primary functions oflubricating and cooling the inside of theengine, and plays a major role in main-taining the engine in proper working order.

ENGINE OIL CONSUMPTION

It is normal that an engine should con-sume some engine oil during normalengine operation. The causes of oilconsumption in a normal engine are asfollows.

� Oil is used to lubricate pistons, pistonrings and cylinders. A thin film of oilis left on the cylinder wall when a pis-ton moves downwards in the cylinder.High negative pressure generated whenthe vehicle is decelerating sucks someof this oil into the combustion chamber.This oil as well as some part of the oilfilm left on the cylinder wall is burnedby the high temperature combustiongases during the combustion process.

� Oil is also used to lubricate the stemsof the intake valves. Some of this oilis sucked into the combustion chambertogether with the intake air and isburned along with the fuel. High tem-perature exhaust gases also burn theoil used to lubricate the exhaust valvestems.

The amount of engine oil consumed de-pends on the viscosity of the oil, thequality of the oil and the conditions thevehicle is driven under.

More oil is consumed by high−speed driv-ing and frequent acceleration and decel-eration.

A new engine consumes more oil, sinceits pistons, piston rings and cylinder wallshave not become conditioned.

When judging the amount of oil con-sumption, note that the oil may becomediluted and make it difficult to judgethe true level accurately.

As an example, if a vehicle is used forrepeated short trips, and consumes a nor-mal amount of oil, the dipstick may notshow any drop in the oil level at all, evenafter 1000 km (600 miles) or more. Thisis because the oil is gradually becomingdiluted with fuel or moisture, making itappear that the oil level has not changed.

The diluting ingredients evaporate outwhen the vehicle is then driven at highspeeds, as on an expressway, making itappear that oil is excessively consumedafter driving at high speeds.

Facts about engine oilconsumption



IMPORTANCE OF ENGINE OIL LEVELCHECK

One of the most important points in prop-er vehicle maintenance is to keep the en-gine oil at the optimum level so that oilfunction will not be impaired. Therefore, itis essential that the oil level be checkedregularly. Toyota recommends that the oillevel be checked every time you refuelthe vehicle.

NOTICE

Failure to check the oil level regularlycould lead to serious engine troubledue to insufficient oil.

For detailed information on oil level check,see “Checking the engine oil level” in Sec-tion 7−2.

Your engine is fitted with iridium−tippedspark plugs.

NOTICE

Use only iridium−tipped spark plugsand do not adjust gaps for your en-gine performance and smooth drive-ability.

The tandem master cylinder brake systemis a hydraulic system with two separatesub−systems. If either sub−system shouldfail, the other will still work. However, thepedal will be harder to press, and yourstopping distance will be longer. Also, thebrake system warning light may come on.

CAUTION

Do not drive your vehicle with only asingle brake system. Have yourbrakes fixed immediately.

BRAKE BOOSTER

The brake booster uses engine vacuum topower−assist the brakes. If the engineshould quit while you are driving, you canbring the vehicle to a stop with normalpedal pressure. There is enough reservedvacuum for one or two stops—but nomore!

Iridium−tipped spark plugs Brake system


132 2002 MY CELICA_U (OM20792U)

CAUTION

� Do not pump the brake pedal if theengine stalls. Each push on thepedal uses up your reserved vacu-um.

� Even if the power assist is com-pletely lost, the brakes will stillwork. But you will have to push thepedal hard, much harder than nor-mal. And your braking distance willbe longer.

ANTI−LOCK BRAKE SYSTEM(with “ABS” warning light)

The anti−lock brake system is designedto help prevent lock−up of the wheelsduring a sudden braking or braking onslippery road surfaces. This assists inproviding directional stability and steer-ing performance of the vehicle underthese circumstances.

Effective way to press the ABS brakepedal: When the anti−lock brake systemfunction is in action, you may feel thebrake pedal pulsating and hear a noise.In this situation, to let the anti−lockbrake system work for you, just hold thebrake pedal down more firmly. Do notpump the brake in a panic stop. Thiswill result in reduced braking performan-ce.

The anti−lock brake system becomes op-erative after the vehicle has acceleratedto a speed in excess of approximately 10km/h (6 mph). It stops operating when thevehicle decelerates to a speed belowapproximately 5 km/h (3 mph).

Depressing the brake pedal on slipperyroad surfaces such as on the manholecover, the steel plate under the construc-tion, joints in the bridge, etc. on a rainyday tends to activate the anti−lock brakesystem.

You may hear a click or motor sound inthe engine compartment for a few secondswhen the engine is started or just afterthe vehicle is started. This means that theanti−lock brake system is in the selfcheck mode, and does not indicate a mal-function.

When the anti−lock brake system is ac-tivated, the following conditions mayoccur. They do not indicate a malfunc-tion of the system:

� You may hear the anti−lock brake sys-tem operating and feel the brake pedalpulsating and the vibrations of the ve-hicle body and steering wheel. Youmay also hear the motor sound in theengine compartment even after the ve-hicle is stopped.

� At the end of the anti−lock brake sys-tem activation, the brake pedal maymove a little forward.

CAUTION

Do not overestimate the anti−lockbrake system: Although the anti−lockbrake system assists in providing ve-hicle control, it is still important todrive with all due care and maintaina moderate speed and safe distancefrom the vehicle in front of you, be-cause there are limits to the vehiclestability and effectiveness of steeringwheel operation even with the anti−lock brake system on.



If tires grip performance exceeds itscapability, or if hydroplaning occursduring high speed driving in the rain,the anti−lock brake system does notprovide vehicle control.

Anti−lock brake system is not de-signed to shorten the stopping dis-tance: Always drive at the moderatespeed and maintain a safe distancefrom the vehicle in front of you.Compared with vehicles without ananti−lock brake system, your vehiclemay require a longer stopping dis-tance in the following cases:

� Driving on rough, gravel or snow−covered roads.

� Driving with tire chains installed.

� Driving over the steps such as thejoints on the road.

� Driving on roads where the roadsurface is pitted or has other differ-ences in surface height.

Install all 4 tires of specified size atappropriate pressure: The anti−lockbrake system detects vehicle speedsusing the speed sensors for respec-tive wheels’ turning speeds. The useof tires other than specified may failto detect the accurate turning speedresulting in a longer stopping dis-tance.

Type A

Type B


134 2002 MY CELICA_U (OM20792U)

“ABS” warning light

The light comes on when the ignition keyis turned to the “ON” position. If the anti−lock brake system works properly, thelight turns off after a few seconds. There-after, if the system malfunctions, the lightcomes on again.

When the “ABS” warning light is on (andthe brake system warning light is off), theanti−lock brake system does not operate,but the brake system still operates con-ventionally.

When the “ABS” warning light is on (andthe brake system warning light is off), theanti−lock brake system does not operateso that the wheels could lock up duringa sudden braking or braking on slipperyroad surfaces.

If either of the following conditionsoccurs, this indicates a malfunctionsomewhere in the parts monitored bythe warning light system. Contact yourToyota dealer as soon as possible toservice the vehicle.

� The light does not come on when theignition key is turned to the “ON” posi-tion, or remains on.

� The light comes on while you are driv-ing.


CAUTION

If the “ABS” warning light remains ontogether with the brake system warn-ing light, immediately stop your ve-hicle at a safe place and contact yourToyota dealer.

In this case, not only the anti−lockbrake system will fail but also thevehicle will become extremely unsta-ble during braking.

DRUM−IN−DISC TYPE PARKING BRAKESYSTEM

Your vehicle has a drum−in−disc typeparking brake system. This type of brakesystem needs bedding−down of the brakeshoes periodically or whenever the parkingbrake shoes and/or drums are replaced.

Have your Toyota dealer perform the bed-ding−down.

The brake pad wear limit indicators onyour disc brakes give a warning noisewhen the brake pads are worn to wherereplacement is required.

If you hear a squealing or scraping noisewhile driving, have the brake padschecked and replaced by your Toyotadealer as soon as possible. Expensive ro-tor damage can result if the pads are notreplaced when necessary.

Brake pad wear limitindicators



When stowing luggage or cargo in thevehicle, observe the following:

� Put luggage or cargo in the luggagecompartment when at all possible. Besure all items are secured in place.

� Be careful to keep the vehicle bal-anced. Locating the weight as far for-ward as possible helps maintain bal-ance.

� For better fuel economy, do not carryunneeded weight.

CAUTION

� To prevent luggage or packagesfrom sliding forward during braking,do not stack anything in the lug-gage compartment higher than theseatbacks. Keep luggage or packagelow, as close to the floor as pos-sible.

� Never allow anyone to ride in theluggage compartment. It is not de-signed for passengers. They shouldride in their seats with their seatbelts properly fastened. Otherwise,they are much more likely to sufferserious bodily injury, in the eventof sudden braking or a collision.

� Do not place anything on the lug-gage cover. Such items may bethrown about and possibly injurepeople in the vehicle during suddenbraking or an accident.

� Do not drive with objects left ontop of the instrument panel. Theymay interfere with the driver’s fieldof view. Or they may move duringsharp vehicle acceleration or turn-ing, and impair the driver’s controlof the vehicle. In an accident theymay injure the vehicle occupants.

NOTICE

Do not load the vehicle beyond thevehicle capacity weight specified inSection 8.

The vehicle identification number (VIN)is the legal identifier for your vehicle.This number is on the left top of theinstrument panel, and can be seenthrough the windshield from outside.

This is the primary identification numberfor your Toyota. It is used in registeringthe ownership of your vehicle.

Luggage stowage precautions

Your Toyota’s identification——Vehicle identificationnumber


136 2002 MY CELICA_U (OM20792U)

The vehicle identification number (VIN) isalso on the Certification Label.

1ZZ−FE engine

2ZZ−GE engine

The engine number is stamped on theengine block as shown.

—Engine number



Your new vehicle carries theft preven-tion labels which are approximately 56mm (2.20 in.) by 16 mm (0.63 in.).

The purpose of these labels is to reducethe incidence of vehicle thefts by facilitat-ing the tracing and recovery of parts fromstolen vehicles. The label is designed sothat once it is applied to a surface, anyattempt to remove it will result in destroy-ing the integrity of the label. Transferringthese labels intact from one part to anoth-er, will be impossible.

NOTICE

You should not attempt to remove thetheft prevention labels as it may vio-late certain state or federal laws.

CAUTION

Do not modify the suspension/chassiswith lift kits, spacers, springs, etc. Itcan cause dangerous handling charac-teristics, resulting in loss of control.

Determine what kind of tires your ve-hicle is originally equipped with.

1. Summer tires

Summer tires are high−speed capabilitytires best suited to highway driving underdry conditions.

Since summer tires do not have the sametraction performance as snow tires, sum-mer tires are inadequate for driving onsnow−covered or icy roads. For driving onsnow−covered or icy roads, we recom-mend using snow tires. If installing snowtires, be sure to replace all four tires.

2. All season tires

All season tires are designed to providebetter traction in snow and to be adequatefor driving in most winter conditions, aswell as for use all year round.

All season tires, however, do not haveadequate traction performance comparedwith snow tires in heavy or loose snow.Also, all season tires fall short in accel-eration and handling performancecompared with summer tires in highwaydriving.

Theft prevention labels(except for Canada) Suspension and chassis Types of tires


138 2002 MY CELICA_U (OM20792U)

CAUTION

� Do not mix summer and all seasontires on your vehicle as this cancause dangerous handling charac-teristics, resulting in loss of con-trol.

� Do not use tires other than themanufacture’s designated tires, andnever mix tires or wheels of thesizes different from the originals.



WE REALLY CARE ABOUT YOU � PLEASE BUCKLE UP

Toyota has made a special effort to encourage use of seat belts.

Toyota belts are:

� Comfortable

� Easy to use

� Convenient

We encourage you to use your belts every time you drive.

U



STARTING AND DRIVINGBefore starting the engine 140. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to start the engine 140. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tips for driving in various conditionsns 141. . . . . . . . . . . . . . . . . . . . . . . . Winter driving tips 142. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dinghy towing 143. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trailer towing 144. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to save fuel and make your vehicle last longer 149. . . . . . . . . . . . .

SECTION 3


140 2002 MY CELICA_U (OM20792U)

1. Check the area around the vehicle be-fore entering it.

2. Adjust seat position, seatback angle,seat cushion angle and steering wheelangle.

3. Adjust the inside and outside rear viewmirrors.

4. Lock both side doors.

5. Fasten seat belts.

1. Apply the parking brake firmly.

2. Turn off unnecessary lights and acces-sories.

3. Manual transmission: Press the clutchpedal to the floor and shift the trans-mission into neutral. Hold the clutchpedal to the floor until the engine isstarted. A starter safety device will pre-vent the starter from operating if theclutch pedal is not fully depressed.

Automatic transmission: Put the se-lector lever in “P”. If you need to re-start the engine while the vehicle ismoving, put the selector lever in “N”.A starter safety device will prevent thestarter from operating if the selectorlever is in any drive position.

4. Automatic transmission only: De-press the brake pedal and hold it tothe floor until driving off.

Before starting the engine, be sure tofollow the instructions in “(a) Beforecranking”.

Normal starting procedure

The multiport fuel injection system/sequen-tial multiport fuel injection system in yourengine automatically controls the properair−fuel mixture for starting. You can starta cold or hot engine as follows:

1. With your foot off the accelerator ped-al, crank the engine by turning the keyto “START”. Release it when the en-gine starts.

2. After the engine runs for about 10 sec-onds, you are ready to drive.

If the weather is below freezing, let theengine warm up for a few minutes beforedriving.

If the engine stalls...

Simply restart it, using the correct proce-dure given in normal starting.

If the engine will not start...

See “If your vehicle will not start” in Sec-tion 4.

Before starting the engineHow to start the engine—(a) Before cranking (b) Starting the engine



NOTICE

� Do not crank for more than 30 sec-onds at a time. This may overheatthe starter and wiring systems.

� Do not race a cold engine.

� If the engine becomes difficult tostart or stalls frequently, have theengine checked immediately.

� Always slow down in gusty crosswinds.This will allow you much better control.

� Drive slowly onto curbs and, if pos-sible, at a right angle. Avoid drivingonto high, sharp−edged objects andother road hazards. Failure to do socan lead to severe tire damage result-ing in tire bursts.

� When parking on a hill, turn the frontwheels until they touch the curb sothat the vehicle will not roll. Apply theparking brake, and place the transmis-sion in “P” (automatic) or in first orreverse (manual). If necessary, blockthe wheels.

� Washing your vehicle or driving throughdeep water may get the brakes wet. Tosee whether they are wet, check thatthere is no traffic near you, and thenpress the pedal lightly. If you do notfeel a normal braking force, the brakesare probably wet. To dry them, drivethe vehicle cautiously while lightlypressing the brake pedal with the park-ing brake applied. If they still do notwork safely, pull to the side of the roadand call a Toyota dealer for assistance.

CAUTION

� Before driving off, make sure thatthe parking brake is fully releasedand the parking brake reminderlight is off.

� Do not leave your vehicle unat-tended while the engine is running.

� Do not rest your foot on the brakepedal while driving. It can causedangerous overheating, needlesswear, and poor fuel economy.

� To drive down a long or steep hill,reduce your speed and downshift.Remember, if you ride the brakesexcessively, they may overheat andnot work properly.

� Be careful when accelerating, up-shifting, downshifting or braking ona slippery surface. Sudden accelera-tion or engine braking, could causethe vehicle to spin or skid.

Tips for driving in variousconditions


142 2002 MY CELICA_U (OM20792U)

� Do not drive in excess of the speedlimit. Even if the legal speed limitpermits it, do not drive over 140km/h (85 mph) unless your vehiclehas high−speed capability tires.Driving over 140 km/h (85 mph) mayresult in tire failure, loss of controland possible injury. Be sure to con-sult a tire dealer to determinewhether the tires on your vehicleare high−speed capability tires ornot before driving at such speeds.

� Do not continue normal drivingwhen the brakes are wet. If they arewet, your vehicle will require a lon-ger stopping distance, and it maypull to one side when the brakesare applied. Also, the parking brakewill not hold the vehicle securely.

Make sure you have a proper freezeprotection of engine coolant.

Your coolant must contain ethylene−glycoltype coolant for a proper corrosionprotection of aluminum components. Use“TOYOTA Long Life Coolant” or equivalent.

See Section 7−2 for details about coolanttype selection.

NOTICE

Do not use alcohol type antifreeze orplain water alone.

When it is extremely cold, we recommendto use 60% solution for your Toyota, toprovide protection down to about −50�C(−58�F). Do not use more than 70% solu-tion for better coolant performance.

Check the condition of the battery andcables.

Cold temperatures reduce the capacity ofany battery, so it must be in top shapeto provide enough power for winter start-ing. Section 7−3 tells you how to visuallyinspect the battery. Your Toyota dealerand most service stations will be pleasedto check the level of charge.

Make sure the engine oil viscosity issuitable for the cold weather.

See Section 7−2 for recommended viscos-ity. Leaving a heavy summer oil in yourvehicle during winter months may causeharder starting. If you are not sure aboutwhich oil to use, call your Toyota deal-er—he will be pleased to help.

Keep the door locks from freezing.

Squirt lock de−icer or glycerine into thelocks to keep them from freezing. To opena frozen lock, try heating the key beforeinserting it.

Use a washer fluid containing an anti-freeze solution.

This product is available at your Toyotadealer and most auto parts stores. Followthe manufacturer’s directions for howmuch to mix with water.

NOTICE

Do not use engine antifreeze or anyother substitute because it may dam-age your vehicle’s paint.

Winter driving tips



Do not use your parking brake whenthere is a possibility it could freeze.

When parking, put the transmission into“P” (automatic) or into first or reverse(manual) and block the rear wheels. Donot use the parking brake, or snow orwater accumulated in and around theparking brake mechanism may freeze,making it hard to release.

Keep ice and snow from accumulatingunder the fenders.

Ice and snow built up under your fenderscan make steering difficult. During badwinter driving, stop and check under thefenders occasionally.

Depending on where you are driving,we recommend you carry some emer-gency equipment.

Some of the things you might put in thevehicle are tire chains, window scraper,bag of sand or salt, flares, small shovel,jumper cables, etc.

NOTICE

Do not use window scraper or deicerwhen the plastic resin moon roof isheavily coated with frost or ice. Theplastic resin moon roof is easily dam-aged.

Your vehicle is not designed to bedinghy towed (with four wheels on theground) behind a motorhome.

NOTICE

Do not tow your vehicle with fourwheels on the ground. This maycause serious damage to your vehicle.

Your vehicle can be dinghy towed (withfour wheels on the ground) from thefront behind a motorhome.

CAUTION

Dinghy towing requires special equip-ment and accessories. Please refer toyour service outlet of the motorhomemanufacture for the recommendedequipment.

Dinghy towing(with automatic transmission)

Dinghy towing(with manual transmission)


144 2002 MY CELICA_U (OM20792U)

NOTICE

Dinghy towing does not eliminate thepossibility of damage to your vehicle.

DINGHY TOWING TIPS

Before dinghy towing, be sure to ob-serve the following in order to reducethe damage to your vehicle.

1. Put the shift lever in neutral.

2. Turn the ignition switch to the “ACC”position. Make sure the audio is turnedoff and any item is not plugged intothe power outlet.

NOTICE

To avoid the locking of the steeringwheel, turn the ignition switch to the“ACC” position.

3. Release the parking brake.

After dinghy towing, let the engine idle formore than 3 minutes before driving thevehicle.

NOTICE

Do not tow your vehicle from therear. This may cause serious damageto your vehicle.

Your vehicle is designed primarily as apassenger−carrying vehicle. Towing atrailer will have an adverse effect onhandling, performance, braking, durabilityand driving economy (fuel consumption,etc.). Your safety and satisfaction dependon the proper use of correct equipmentand cautious driving habits. For yoursafety and the safety of others, you mustnot overload your vehicle or trailer. Toyotawarranties do not apply to damage ormalfunction caused by towing a trailer forcommercial purposes. Ask your localToyota dealer for further details beforetowing.

WEIGHT LIMITS

Before towing, make sure the total trailerweight, gross vehicle weight, gross axleweight and trailer tongue load are all with-in the limits.

The total trailer weight and tongue loadcan be measured with platform scalesfound at a highway weighing station, build-ing supply company, trucking company,junk yard, etc.

Trailer towing



CAUTION

� The total trailer weight (trailerweight plus its cargo load) mustnot exceed 907 kg (2000 lb.). Ex-ceeding this weight is dangerous.

� Trailer hitch assemblies have differ-ent weight capacities established bythe hitch manufacturer. Even thoughthe vehicle may be physically capa-ble of towing a higher weight, theoperator must determine the maxi-mum weight rating of the particularhitch assembly and never exceedthe maximum weight rating speci-fied for the trailer−hitch. Exceedingthe maximum weight rating set bythe trailer hitch manufacturer cancause an accident resulting in seri-ous personal injuries.

Total trailer weight

Total trailer weight

Tongue load

Tongue load

� 100 = 9 to 11%

� The gross vehicle weight must notexceed the Gross Vehicle WeightRating (GVWR) indicated on theCertification Label. The gross ve-hicle weight is the sum of weightsof the unloaded vehicle, driver, pas-sengers, luggage, hitch and trailertongue load. It also includes theweight of any special equipmentinstalled on your vehicle.

� The load on either the front or rearaxle resulting from distribution ofthe gross vehicle weight on bothaxles must not exceed the GrossAxle Weight Rating (GAWR) listedon the Certification Label.


146 2002 MY CELICA_U (OM20792U)

� The trailer cargo load should bedistributed so that the tongue loadis 9 to 11% of the total trailerweight, not exceeding the maximumof 90 kg (200 lb.). Never load thetrailer with more weight in the backthan in the front. About 60% of thetrailer load should be in the fronthalf of the trailer and the remaining40% in the rear.

HITCHES

� Use only a hitch which is recom-mended by the hitch manufacturer andconforms to the total trailer weight re-quirement.

� Follow the directions supplied by thehitch manufacturer, and bolt the hitchsecurely to the rear bumper. Lubricatethe hitch ball with a light coat ofgrease.

� Toyota recommends removing the trail-er hitch whenever you are not towinga trailer to reduce the possibility ofadditional damage caused by the hitchif your vehicle is struck from behind.After removing the hitch, seal anymounting holes in the vehicle body toprevent entry of pollutants such as ex-haust fumes, dirt, water, etc.

NOTICE

Do not use axle−mounted hitches asthey can cause damage to the axlehousing, wheel bearings, wheels ortires. Also, never install a hitch whichmay interfere with the normal functionof an Energy Absorbing Bumper.

BRAKES AND SAFETY CHAINS

� Toyota recommends trailers withbrakes that conform to any applica-ble federal and state/provincial regu-lations.

� A safety chain must always be usedbetween the towing vehicle and thetrailer. Leave sufficient slack in thechain for turns. The chain shouldcross under the trailer tongue toprevent the tongue from dropping tothe ground in case it becomes dam-aged or separated. For correct safetychain procedures, follow the hitch ortrailer manufacturer’s recommenda-tions.

CAUTION

� If the total trailer weight exceeds453 kg (1000 lb.), trailer brakes arerequired.

� Never tap into your vehicle’s hy-draulic system as it would lower itsbraking effectiveness.

� Never tow a trailer without using asafety chain securely attached toboth the trailer and the vehicle. Ifdamage occurs to the coupling unitor hitch ball, there is danger of thetrailer wandering over into anotherlane.



TIRES

� Ensure that your vehicle’s tires areproperly inflated. See Section 7−2 forinstructions.

� The trailer tires should be inflated tothe pressure recommended by the trail-er manufacturer in respect to the totaltrailer weight.

TRAILER LIGHTS

� Trailer lights must comply with federal,state/provincial and local regulations.See your local recreational vehicledealer or rental agency for the correcttype of wiring and relays for your trail-er. Check for correct operation of theturn signals and stop lights each timeyou hitch up. Direct splicing may dam-age your vehicle’s electrical systemand cause a malfunction of your lights.

BREAK−IN SCHEDULE

� Toyota recommends that you do nottow a trailer with a new vehicle or avehicle with any new power train com-ponent (engine, transmission, differen-tial, wheel bearing, etc.) for the first800 km (500 miles) of driving.

MAINTENANCE

� If you tow a trailer, your vehicle willrequire more frequent maintenance dueto the additional load. For thisinformation, please refer to thescheduled maintenance information inthe “Scheduled Maintenance Guide” or“Owner’s Manual Supplement”.

� Retighten all fixing bolts of the towingball and bracket after approximately1000 km (600 miles) of trailer driving.

PRE−TOWING SAFETY CHECK

� Check that your vehicle remains a lev-el when a loaded or unloaded trailer ishitched. Do not drive if the vehicle hasan abnormal nose−up or nose−downcondition, and check for impropertongue load, overload, worn suspensionor other possible causes.

� Make sure the trailer cargo is securelyloaded so that it can not shift.

� Check that your rear view mirrors con-form to any applicable federal, state/provincial or local regulations. If not,install the rear view mirrors requiredfor towing purpose.

TRAILER TOWING TIPS

When towing a trailer, your vehicle willhandle differently than when not tow-ing. The three main causes of vehicle−trailer accidents are driver error, exces-sive speed and improper trailer loading.Keep these in mind when towing:

� Before starting out, check operation ofthe lights and all vehicle−trailer connec-tions. After driving a short distance,stop and recheck the lights and con-nections. Before actually towing a trail-er, practice turning, stopping and back-ing with a trailer in an area away fromtraffic until you learn the feel.

� Backing with a trailer is difficult andrequires practice. Grip the bottom ofthe steering wheel and move your handto the left to move the trailer to theleft. Move your hand to the right tomove the trailer to the right. (This pro-cedure is generally opposite to thatwhen backing without a trailer.) Also,just turn the steering wheel a little ata time, avoiding sharp or prolongedturning. Have someone guide you whenbacking to reduce the risk of an acci-dent.


148 2002 MY CELICA_U (OM20792U)

� Because stopping distance may be in-creased, vehicle−to−vehicle distanceshould be increased when towing atrailer. For each 16 km/h (10 mph) ofspeed, allow at least one vehicle andtrailer length between you and the ve-hicle ahead. Avoid sudden braking asyou may skid, resulting in jackknifingand loss of control. This is especiallytrue on wet or slippery surfaces.

� Avoid jerky starts or sudden accelera-tion. If your vehicle has a manualtransmission, prevent excessive clutchslippage by keeping engine rpm lowand not racing the engine. Always startout in first gear.

� Avoid jerky steering and sharp turns.The trailer could hit your vehicle in atight turn. Slow down before making aturn to avoid the necessity of suddenbraking.

� Remember that when making a turn,the trailer wheels will be closer thanthe vehicle wheels to the inside of theturn. Therefore, compensate for this bymaking a larger than normal turningradius with your vehicle.

� Crosswinds and rough roads will ad-versely affect handling of your vehicleand trailer, causing sway. Pay attentionto the rear from time to time to pre-pare yourself for being passed by largetrucks or buses, which may cause yourvehicle and trailer to sway. If swayinghappens, firmly grip the steering wheeland reduce speed immediately butgradually. Never increase speed. Steerstraight ahead. If you make no extremecorrection with the steering or brakes,the vehicle and trailer will stabilize.

� Be careful when passing other ve-hicles. Passing requires considerabledistance. After passing a vehicle, donot forget the length of your trailer andbe sure you have plenty of room be-fore changing lanes.

� In order to maintain engine braking effi-ciency do not use fifth gear (5−speedmanual transmission), sixth gear(6−speed manual transmission) or over-drive (automatic transmission).

� Because of the added load of the trail-er, your vehicle’s engine may overheaton hot days (at temperatures over30�C [85�F]) when going up a long orsteep grade with a trailer. If the enginecoolant temperature gauge indicatesoverheating, immediately turn off the airconditioning (if in use), pull off the roadand stop in a safe spot. Refer to “Ifyour vehicle overheats” in Section 4.

� Always place wheel blocks under boththe vehicle and trailer wheels whenparking. Apply the parking brake firmly.Put the transmission in “P” (automatic)or in first or reverse (manual). Avoidparking on a slope with a trailer, butif it cannot be avoided, do so onlyafter performing the following:

1. Apply the brakes and hold.

2. Have someone place wheel blocks un-der both the vehicle and trailer wheels.

3. When the wheel blocks are in place,release your brakes slowly until theblocks absorb the load.

4. Apply the parking brake firmly.

5. Shift into first or reverse (manual) or“P” (automatic) and turn off the engine.



When restarting out after parking on aslope:

1. With the transmission in “P” position(automatic) or the clutch pedal de-pressed (manual), start the engine.(With an automatic transmission, besure to keep the brake pedal de-pressed.)

2. Shift into gear.

3. Release the parking brake (also footbrake on automatic transmission ve-hicles) and slowly pull or back awayfrom the wheel blocks. Stop and applyyour brakes.

4. Have someone retrieve the blocks.

CAUTION

� Do not exceed 72 km/h (45 mph) orthe posted towing speed limit,whichever is lower. Because insta-bility (swaying) of a towing vehicle−trailer combination usually in-creases as the speed increases, ex-ceeding 72 km/h (45 mph) maycause loss of control.

� Slow down and downshift beforedescending steep or long downhillgrades. Do not make sudden down-shifts.

� Avoid holding the brake pedal downtoo long or too frequently. Thiscould cause the brakes to overheatand result in reduced braking effi-ciency.

Improving fuel economy is easy—just takeit easy. It will help make your vehicle lastlonger, too. Here are some specific tipson how to save money on both fuel andrepairs:

� Keep your tires inflated at the cor-rect pressure. Underinflation causestire wear and wastes fuel. See Section7−2 for instructions.

� Do not carry unneeded weight inyour vehicle. Excess weight puts aheavier load on the engine, causinggreater fuel consumption.

� Avoid lengthy warm−up idling. Oncethe engine is running smoothly, begindriving—but gently. Remember, howev-er, that on cold winter days this maytake a little longer.

� Keep the automatic transmissionoverdrive turned on when enginebraking is not required. Driving withthe overdrive off will reduce the fueleconomy. (For details, see “Automatictransmission” in Section 1−6.)

� Accelerate slowly and smoothly.Avoid jackrabbit starts. Get into highgear as quickly as possible.

How to save fuel and makeyour vehicle last longer


150 2002 MY CELICA_U (OM20792U)

� Avoid long engine idling. If you havea long wait and you are not in traffic,it is better to turn off the engine andstart again later.

� Avoid engine lugging or over−rev-ving. Use a gear position suitable forthe road on which you are travelling.

� Avoid continuous speeding up andslowing down. Stop−and−go drivingwastes fuel.

� Avoid unnecessary stopping andbraking. Maintain a steady pace. Tryto time the traffic signals so you onlyneed to stop as little as possible ortake advantage of through streets toavoid traffic lights. Keep a proper dis-tance from other vehicles to avoid sud-den braking. This will also reduce wearon your brakes.

� Avoid heavy traffic or traffic jamswhenever possible.

� Do not rest your foot on the clutchor brake pedal. This causes prematurewear, overheating and poor fuel econo-my.

� Maintain a moderate speed on high-ways. The faster you drive, the greaterthe fuel consumption. By reducing yourspeed, you will cut down on fuel con-sumption.

� Keep the front wheels in properalignment. Avoid hitting the curb andslow down on rough roads. Improperalignment not only causes faster tirewear but also puts an extra load onthe engine, which, in turn, wastes fuel.

� Keep the bottom of your vehicle freefrom mud, etc. This not only lessensweight but also helps prevent corro-sion.

� Keep your vehicle tuned−up and intop shape. A dirty air cleaner, improp-er valve clearance, dirty plugs, dirty oiland grease, brakes not adjusted, etc.all lower engine performance and con-tribute to poor fuel economy. For longerlife of all parts and lower operatingcosts, keep all maintenance work onschedule, and if you often drive undersevere conditions, see that your vehiclereceives more frequent maintenance.(For scheduled maintenance informa-tion, please refer to the “ScheduledMaintenance Guide” or “Owner’s Manu-al Supplement”.)

CAUTION

Never turn off the engine to coastdown hills. Your power steering andbrake booster will not function with-out the engine running. Also, theemission control system operatesproperly only when the engine is run-ning.



IN CASE OF AN EMERGENCYIf your vehicle will not start 152. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If your engine stalls while drivingng 155. . . . . . . . . . . . . . . . . . . . . . . . . . . If your vehicle overheats 155. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If you have a flat tire 156. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If your vehicle needs to be toweded 166. . . . . . . . . . . . . . . . . . . . . . . . . . . If you cannot shift automatic transmission selector leverer 169. . . . . . . If you lose your keys 169. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . If you lose your wireless remote control transmitter 170. . . . . . . . . . . . .

SECTION 4


152 2002 MY CELICA_U (OM20792U)

Before making these checks, make sureyou have followed the correct starting pro-cedure given in “How to start the engine”in Section 3 and that you have sufficientfuel.

If the engine is not turning over or isturning over too slowly—

1. Check that the battery terminals aretight and clean.

2. If the battery terminals are O.K., switchon the interior light.

3. If the light is out, dim or goes outwhen the starter is cranked, the batteryis discharged. You may try jump start-ing. See “(c) Jump starting” for furtherinstructions.

If the light is O.K., but the engine still willnot start, it needs adjustment or repair.Call a Toyota dealer or qualified repairshop.

NOTICE

Do not pull− or push−start the vehicle.It may damage the vehicle or cause acollision when the engine starts. Alsothe three−way catalytic converter mayoverheat and become a fire hazard.

If the engine turns over at its normalspeed but will not start—

1. Turn the ignition key to “ACC” or“LOCK” and try starting the engineagain.

2. If the engine will not start, the enginemay be flooded because of repeatedcranking. See “(b) Starting a floodedengine” for further instructions.

3. If the engine still will not start, it needsadjustment or repair. Call a Toyotadealer or qualified repair shop.

If the engine will not start, your enginemay be flooded because of repeatedcranking.

If this happens, turn the key to “START”with the accelerator pedal held down.Keep the key and accelerator pedal so for15 seconds and release them. Then trystarting the engine with your foot off theaccelerator pedal.

If the engine does not start after 15 se-conds of cranking, release the key, waita few minutes and try again.

If the engine still will not start, it needsadjustment or repair. Call a Toyota dealeror qualified repair shop for assistance.

NOTICE

Do not crank for more than 30 secondsat a time. This may overheat the starterand wiring systems.

If your vehicle will not start—(a) Simple checks (b) Starting a flooded engine



To avoid serious personal injury anddamage to your vehicle which might re-sult from battery explosion, acid burns,electrical burns, or damaged electroniccomponents, these instructions must befollowed precisely.

If you are unsure about how to follow thisprocedure, we strongly recommend thatyou seek the help of a competent me-chanic or towing service.

CAUTION

� Batteries contain sulfuric acidwhich is poisonous and corrosive.Wear protective safety glasses whenjump starting, and avoid spillingacid on your skin, clothing, or ve-hicle.

� If you should accidentally get acidon yourself or in your eyes, removeany contaminated clothing and flushthe affected area with water imme-diately. Then get immediate medicalattention. If possible, continue toapply water with a sponge or clothwhile en route to the medical office.

� The gas normally produced by abattery will explode if a flame orspark is brought near. Use onlystandardized jumper cables and donot smoke or light a match whilejump starting.

� Warning: Battery posts, terminalsand related accessories contain leadand lead compounds, chemicalsknown to the State of California tocause cancer and reproductiveharm. Wash hands after handling.

NOTICE

The battery used for boosting mustbe 12 V. Do not jump start unless youare sure that the booster battery iscorrect.

JUMP STARTING PROCEDURE

1. If the booster battery is installed inanother vehicle, make sure the vehiclesare not touching. Turn off all unneces-sary lights and accessories.

2. If required, remove all the vent plugsfrom the booster and discharged batter-ies. Lay a cloth over the open ventson the batteries. (This helps reduce theexplosion hazard, personal injuries andburns.)

3. If the engine in the vehicle with thebooster battery is not running, start itand let it run for a few minutes. Duringjump starting, run the engine at about2000 rpm with the accelerator pedallightly depressed.

(c) Jump starting


154 2002 MY CELICA_U (OM20792U)

Discharged battery

Boosterbattery

Positive terminal(“+” mark)

Jumpercable

Positiveterminal(“+” mark)

4. Make the cable connections in the or-der a, b, c, d.

a. Connect the clamp of the positive(red) jumper cable to the positive (+)terminal on the discharged battery.

b. Connect the clamp at the other endof the positive (red) jumper cable tothe positive (+) terminal on the boosterbattery.

Jumper cable

BoosterbatteryNegative terminal

(“−” mark)

Discharged battery

c. Connect the clamp of the negative(black) jumper cable to the negative (–)terminal on the booster battery.

d. Connect the clamp at the other endof the negative (black) jumper cable toa solid, stationary, unpainted, metallicpoint of the vehicle with the dischargedbattery.

The recommended connecting point isshown in the following illustration:

Connecting point

Do not connect the cable to or nearany part that moves when the engineis cranked.

CAUTION

When making the connections, toavoid serious injury, do not lean overthe battery or accidentally let thejumper cables or clamps touch any-thing except the correct battery termi-nals or the ground.



5. Start your engine in the normal way.After starting, run it at about 2000 rpmfor several minutes with the acceleratorpedal lightly depressed.

6. Carefully disconnect the cables in theexact reverse order: the negative cableand then the positive cable.

7. Carefully dispose of the battery covercloths—they may now contain sulfuricacid.

8. If removed, replace all the battery ventplugs.

If the cause of your battery discharging isnot apparent (for example, lights left on),you should have it checked.

If your engine stalls while driving...

1. Reduce your speed gradually, keepinga straight line. Move cautiously off theroad to a safe place.

2. Turn on your emergency flashers.

3. Turn the ignition key to “ACC” or“LOCK”, and try starting the engineagain.

If the engine will not start, see “If yourvehicle will not start” in this section.

CAUTION

If the engine is not running, the pow-er assist for the brakes and steeringwill not work so steering and brakingwill be much harder than usual.

If your engine coolant temperaturegauge indicates overheating, if you ex-perience a loss of power, or if you heara loud knocking or pinging noise, theengine has probably overheated. Youshould follow this procedure...

1. Pull safely off the road, stop the ve-hicle and turn on your emergencyflashers. Put the transmission in “P”(automatic) or neutral (manual) and ap-ply the parking brake. Turn off the airconditioning if it is being used.

2. If coolant or steam is boiling out of theradiator or reservoir, stop the engine.Wait until the steam subsides beforeopening the hood. If there is no coolantboiling over or steam, leave the enginerunning and make sure the electriccooling fan is operating. If it is not,turn the ignition off.

CAUTION

To help avoid personal injury, keepthe hood closed until there is nosteam. Escaping steam or coolant isa sign of very high pressure.

If your engine stalls whiledriving If your vehicle overheats


156 2002 MY CELICA_U (OM20792U)

3. Look for obvious coolant leaks from theradiator, hoses, and under the vehicle.However, note that water draining fromthe air conditioning is normal if it hasbeen used.

CAUTION

When the engine is running, keephands and clothing away from themoving fan and engine drive belts.

4. If the coolant is leaking, stop the en-gine immediately. Call a Toyota dealerfor assistance.

5. If there are no obvious leaks, checkthe coolant reservoir.

If it is dry, call a Toyota dealer forassistance as soon as possible.

If there is enough coolant in the reser-voir, again check the coolant level inthe reservoir after the engine coolanttemperature has cooled to normal. Seri-ous coolant loss indicates a leak in thesystem. You should have it checked assoon as possible at you Toyota dealer.

CAUTION

Do not attempt to touch the coolantreservoir tank when the engine andradiator are hot. Serious injury couldresult from scalding hot fluid andsteam blown out under pressure.

1. Reduce your speed gradually, keepinga straight line. Move cautiously off theroad to a safe place well away fromthe traffic. Avoid stopping on the centerdivider of a highway. Park on a levelspot with firm ground.

2. Stop the engine and turn on youremergency flashers.

3. Firmly set the parking brake and putthe transmission in “P” (automatic) orreverse (manual).

4. Have everyone get out of the vehicleon the side away from traffic.

5. Read the following instructions thor-oughly.

CAUTION

When jacking, be sure to observe thefollowing to reduce the possibility ofpersonal injury:

� Follow jacking instructions.

� Do not put any part of your bodyunder the vehicle supported by thejack. Personal injury may occur.

� Do not start or run the engine whileyour vehicle is supported by thejack.

If you have a flat tire—



� Stop the vehicle on a level firmground, firmly set the parking brakeand put the transmission in “P”(automatic) or reverse (manual).Block the wheel diagonally oppositeto the one being changed if neces-sary.

� Make sure to set the jack properlyin the jack point. Raising the ve-hicle with jack improperly posi-tioned will damage the vehicle ormay allow the vehicle to fall off thejack and cause personal injury.

� Never get under the vehicle whenthe vehicle is supported by the jackalone.

� Use the jack only for lifting yourvehicle during wheel changing.

� Do not raise the vehicle with some-one in the vehicle.

� When raising the vehicle, do notput an object on or under the jack.

� Raise the vehicle only high enoughto remove and change the tire.

NOTICE

Do not continue driving with a de-flated tire. Driving even a short dis-tance can damage a tire and wheelbeyond repair.

Type A

Type B

Spare tire with turning direction indica-tors (some models)

The spare tires with turning directionindicators are uni−directional and in-tended to be used so that they turn inthe same direction as the turning direc-tion indicators.

Installing the wheel on the driver side ofthe vehicle will not affect tire performance.If the spare tire is used on the driver sideof the vehicle, it should be used onlytemporarily and then replaced with thecorrect one.


158 2002 MY CELICA_U (OM20792U)

Compact spare tire

The compact spare tire is designed fortemporary emergency use only.

The compact spare tire is identified by thedistinctive wheel design and color andspecial wording “TEMPORARY USE ONLY”molded into the side wall of the tire.

The standard tire should be repaired andreplaced as soon as possible.

The compact spare tire saves space inyour trunk or luggage compartment, andits lighter weight helps to improve fueleconomy and permits easier installation incase of a flat tire.

The compact spare tire can be used manytimes, if necessary. It has tread life of upto 4800 km (3000 miles) depending onroad conditions and your driving habits.When tread wear indicators appear on thetire, replace the tire.

See also the tire section in Section 7−2for details on the tread wear indicatorsand other service information.

CAUTION

� The compact spare tire was de-signed especially for your Toyota.Do not use it on any other vehicle.

� Do not exceed 80 km/h (50 mph)when driving with the compactspare tire.

� Avoid sudden acceleration, suddendeceleration and sharp turns withthe compact spare tire.

NOTICE

Your ground clearance is reducedwhen the compact spare tire isinstalled so avoid driving over ob-stacles and drive slowly on rough,unpaved roads and speed bumps.Also, do not attempt to go through anautomatic car wash as the vehiclemay get caught, resulting in damage.



With a compact spare tire

Without a compact spare tire

1. Get the required tools and sparetire.

1 Jack2 Wheel nut wrench3 Spare tire4 Jack handle

To prepare yourself for an emergency, youshould familiarize yourself with the use ofthe jack, each of the tools and their stor-age locations.

To remove the jack:

1. Turn the jack joint by hand until thejack becomes free.

CAUTION

When removing the jack, be carefulnot to injure your hands with theedge of the trim.

—Required tools and sparetire


160 2002 MY CELICA_U (OM20792U)

2. Twist the jack head clockwise and pullout the jack.

To store the jack, put the jack base onthe fitting place. Turn the joint until thejack upper side fits securely with the pro-trusion of the carrier.

This prevents the jack from flying forwardduring a collision or sudden braking.

CAUTION

When storing the jack, be careful notto injure your hands with the edge ofthe trim.

To remove the spare tire:

1. Remove the spare tire cover.

2. Loosen the bolt and remove it.

Then take the spare tire out of the ve-hicle.

When storing the spare tire, put it in placewith the inner side of the wheel facing up.Then secure the tire by repeating theabove removal steps in reverse order toprevent it from flying forward during acollision or sudden braking.



2. Block the wheel diagonally oppositethe flat tire to keep the vehicle fromrolling when it is jacked up.

When blocking the wheel, place a wheelblock from the front for the front wheelsor from the rear for the rear wheels.

Steel wheels

Aluminum wheels

3. Remove the wheel ornament.

Pry off the wheel ornament, using thebeveled end of the wheel nut wrench asshown.

CAUTION

Do not try to pull off the ornament byhand. Take due care in handling theornament to avoid unexpected person-al injury.

—Blocking the wheel —Removing wheel ornament


162 2002 MY CELICA_U (OM20792U)

4. Loosen all the wheel nuts.

Always loosen the wheel nuts before rais-ing the vehicle.

Turn the wheel nuts counterclockwise toloosen. To get maximum leverage, fit thewrench to the nut so that the handle ison the right side, as shown above. Grabthe wrench near the end of the handleand pull up on the handle. Be careful thatthe wrench does not slip off the nut.

Do not remove the nuts yet—just unscrewthem about one—half turn.

5. Position the jack at the correct jackpoint as shown.

Make sure the jack is positioned on alevel and solid place.

6. After making sure that no one is inthe vehicle, raise it high enough sothat the spare tire can be installed.

Remember you will need more groundclearance when putting on the spare tirethan when removing the flat tire.

To raise the vehicle, insert the jack handleinto the jack (it is a loose fit) and turn itclockwise. As the jack touches the vehicleand begins to lift, double−check that it isproperly positioned.

—Loosening wheel nuts —Positioning the jack —Raising your vehicle



CAUTION

Never get under the vehicle when thevehicle is supported by the jackalone.

7. Remove the wheel nuts and changetires.

Lift the flat tire straight off and put itaside.

Roll the spare wheel into position andalign the holes in the wheel with the bolts.Then lift up the wheel and get at least thetop bolt started through its hole. Wigglethe tire and press it back over the otherbolts.

Before putting on wheels, remove any cor-rosion on the mounting surfaces with awire brush or such. Installation of wheelswithout good metal−to−metal contact at themounting surface can cause wheel nuts toloosen and eventually cause a wheel tocome off while driving. Therefore after thefirst 1600 km (1000 miles), check to seethat the wheel nuts are tight.

—Changing wheels


164 2002 MY CELICA_U (OM20792U)

8. Reinstall all the wheel nuts fingertight.

Reinstall the wheel nuts (tapered end in-ward) and tighten them as much as youcan by hand. Press back on the tire backand see if you can tighten them more.

9. Lower the vehicle completely andtighten the wheel nuts.

Turn the jack handle counterclockwise tolower the vehicle.

Use only the wheel nut wrench and turnit clockwise to tighten the nuts. Do notuse other tools or any additional leverageother than your hands, such as a hammer,pipe or your foot. Make sure the wrenchis securely engaged over the nut.

Tighten each nut a little at a time in theorder shown. Repeat the process until allthe nuts are tight.

CAUTION

When lowering the vehicle, make sureall portions of your body and all oth-er persons around will not be injuredas the vehicle is lowered to theground.

—Reinstalling wheel nuts —Lowering your vehicle



Steel wheels

Aluminum wheels

10. Reinstall the wheel ornament.

1. Put the wheel ornament into position.

Steel wheels—Align the cutout of thewheel ornament with the valve stem asshown.

2. Then tap it firmly with the side or heelof your hand to snap it into place.

CAUTION

Take due care in handling the orna-ment to avoid unexpected personalinjury.

11. Check the air pressure of the re-placed tire.

Adjust the air pressure to the specificationdesignated in Section 8. If the pressure islower, drive slowly to the nearest servicestation and fill to the correct pressure.

Do not forget to reinstall the tire inflationvalve cap as dirt and moisture could getinto the valve core and possibly cause airleakage. If the cap is missing, have a newone put on as soon as possible.

12. Restow all the tools, jack and flattire securely.

As soon after changing wheels as pos-sible, tighten the wheel nuts to the torquespecified in Section 8 with a torquewrench. Have a technician repair the flattire and replace the spare tire with it.

CAUTION

Before driving, make sure all thetools, jack and flat tire are securelyin place in their storage location toreduce the possibility of personal in-jury during a collision or suddenbraking.

—Reinstalling wheel ornament —After changing wheels


166 2002 MY CELICA_U (OM20792U)

(a) Towing with wheel lift type truck—

—From front

—From rear

(b) Using flat bed truck

If towing is necessary, we recommendyou to have it done by your Toyotadealer or a commercial tow truck ser-vice. In consultation with them, haveyour vehicle towed using either (a) or(b).

Only when you cannot receive a towingservice from a Toyota dealer orcommercial tow truck service, tow yourvehicle carefully in accordance with theinstructions given in “—Emergencytowing” in this section.

Proper equipment will help ensure thatyour vehicle is not damaged while beingtowed. Commercial operators are generallyaware of the state/provincial and locallaws pertaining to towing.

Your vehicle can be damaged if it istowed incorrectly. Although most operatorsknow the correct procedure, it is possibleto make a mistake. To avoid damage toyour vehicle, make sure the following pre-cautions are observed. If necessary, showthis page to the tow truck driver.

TOWING PRECAUTIONS:

Use a safety chain system for all towing,and abide by the state/provincial and locallaws. The wheels and axle on the groundmust be in good condition. If they aredamaged, use a towing dolly.

(a) Towing with wheel lift type truck

From front—Release the parking brake.

NOTICE

When lifting wheels, take care to en-sure adequate ground clearance fortowing at the opposite end of theraised vehicle. Otherwise, the bumperand/or underbody of the towed vehiclewill be damaged during towing.

From rear—

� Manual transmission:

We recommend using a towing dollyunder the front wheels. If you do notuse a towing dolly, place the ignitionkey in the “ACC” position and put thetransmission in neutral.

NOTICE

Do not tow with the key removed orin the “LOCK” position when towingfrom the rear without a towing dolly.The steering lock mechanism is notstrong enough to hold the frontwheels straight.

If your vehicle needs to betowed—



� Automatic transmission:

Use a towing dolly under the frontwheels.

NOTICE

Never tow a vehicle with an automatictransmission from the rear with thefront wheels on the ground, as thismay cause serious damage to thetransmission.

(b) Using flat bed truck

(c) Towing with sling type truck

(c) Towing with sling type truck

NOTICE

Do not tow with sling type truck, ei-ther from the front or rear. This maycause body damage.

Front

Rear

—Emergency towing


168 2002 MY CELICA_U (OM20792U)

If towing is necessary, we recommendyou to have it done by your Toyotadealer or a commercial tow truck ser-vice.

If towing service is not available in anemergency, your vehicle may be tempo-rarily towed by a cable or chain se-cured to the emergency towing eyeletunder the front of the vehicle or theleft emergency towing eyelet under therear of the vehicle. Use extreme cautionwhen towing vehicles.

NOTICE

Only use specified towing eyelet;otherwise your vehicle may be dam-aged.

A driver must be in the vehicle to steerit and operate the brakes.

Towing in this manner may be done onlyon hard−surfaced roads for a short dis-tance and at low speeds. Also, thewheels, axles, drive train, steering andbrakes must all be in good condition.

CAUTION

Use extreme caution when towing ve-hicles. Avoid sudden starts or erraticdriving maneuvers which would placeexcessive stress on the emergencytowing eyelets and towing cable orchain. The eyelets and towing cableor chain may break and cause seriousinjury or damage.

NOTICE

Use only a cable or chain specificallyintended for use in towing vehicles.Securely fasten the cable or chain tothe towing eyelets provided.

Before towing, release the parking brakeand put the transmission in neutral (manu-al) or “N” (automatic). The key must bein “ACC” (engine off) or “ON” (engine run-ning).

CAUTION

If the engine is not running, the pow-er assist for the brakes and steeringwill not work so steering and brakingwill be much harder than usual.



If you cannot shift the selector leverout of “P” position to other positionseven though the brake pedal is de-pressed, use the shift lock override but-ton as follows:

1. Turn the ignition key to “LOCK”position. Make sure the parkingbrake is applied.

2. Pry up the cover with a flat−bladedscrewdriver or equivalent.

3. Insert your finger into the hole topush down the shift lock overridebutton. You can shift out of “P”position only while pushing the but-ton.

4. Shift into “N” position.

5. Insert the cover.

6. Start the engine. For your safety,keep the brake pedal depressed.

Be sure to have the system checked byyour Toyota dealer as soon as possible.

You can purchase a new key at yourToyota dealer if you can give them thekey number.

See the suggestion given in “Keys” inSection 1−2.

If your keys are locked in the vehicle andyou cannot get a duplicate, many Toyotadealers can still open the door for you,using their special tools. If you mustbreak a window to get in, we suggestbreaking the smallest side window be-cause it is the least expensive to replace.Be extremely cautious to avoid cuts fromthe glass.

If you cannot shift automatictransmission selector lever If you lose your keys


170 2002 MY CELICA_U (OM20792U)

You can purchase a new wireless re-mote control transmitter at your Toyotadealer.

Have the registered identification numbersof your transmitters deleted from your ve-hicle by your Toyota dealer as soon aspossible to avoid the possibility of theft oran accident. Then, have the identificationnumber of your new transmitter registered.At the same time, you must bring all ofthe remaining transmitters to have themregistered again as well.

You can use the wireless remote controlsystem with the new transmitter. Contactyour Toyota dealer for detailed information.

If you lose your wirelessremote control transmitter



CORROSION PREVENTION ANDAPPEARANCE CAREProtecting your Toyota from corrosionon 172. . . . . . . . . . . . . . . . . . . . . . . Washing and waxing your Toyota 173. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the interior 175. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 5


172 2002 MY CELICA_U (OM20792U)

Toyota, through its diligent research, de-sign and use of the most advancedtechnology available, has done its part tohelp prevent corrosion and has providedyou with the finest quality vehicleconstruction. Now, it is up to you. Propercare of your Toyota can help ensure long−term corrosion prevention.

The most common causes of corrosionto your vehicle are:

� The accumulation of road salt, dirt andmoisture in hard−to−reach areas underthe vehicle.

� Chipping of paint, or undercoatingcaused by minor accidents or bystones and gravel.

Care is especially important if you livein particular areas or operate your ve-hicle under certain environmental condi-tions:

� Road salt or dust control chemicals willaccelerate corrosion, as will the pres-ence of salt in the air near the sea−coast or in areas of industrial pollution.

� High humidity accelerates corrosion es-pecially when temperatures range justabove the freezing point.

� Wetness or dampness to certain partsof your vehicle for an extended periodof time, may cause corrosion eventhough other parts of the vehicle maybe dry.

� High ambient temperatures can causecorrosion to those components of thevehicle which are prevented fromquick−drying due to lack of proper ven-tilation.

The above signifies the necessity to keepyour vehicle, particularly the underside, asclean as possible and to repair any dam-age to paint or protective coatings assoon as possible.

To help prevent corrosion on yourToyota, follow these guidelines:

Wash your vehicle frequently. It is, ofcourse, necessary to keep your vehicleclean by regular washing, but to preventcorrosion, the following points should beobserved:

� If you drive on salted roads in thewinter or if you live near the ocean,you should hose off the undercarriageat least once a month to minimize cor-rosion.

� High pressure water or steam is effec-tive for cleaning the vehicle’s undersideand wheel housings. Pay particularattention to these areas as it is difficultto see all the mud and dirt. It will domore harm than good to simply wet themud and debris without removing them.The lower edge of doors, rocker panelsand frame members have drain holeswhich should not be allowed to clogwith dirt as trapped water in theseareas can cause corrosion.

� Wash the underside of the vehicle thor-oughly when winter is over.

See “Washing and waxing your Toyota” formore tips.

Check the condition of your vehicle’spaint and trim. If you find any chips orscratches in the paint, touch them up im-mediately to prevent corrosion from start-ing. If the chips or scratches have gonethrough the bare metal, have a qualifiedbody shop make the repair.

Protecting your Toyota fromcorrosion



Check the interior of your vehicle. Wa-ter and dirt can accumulate under thefloor mats and could cause corrosion. Oc-casionally check under the mats to makesure the area is dry. Be particularly care-ful when transporting chemicals, cleans-ers, fertilizers, salt, etc.; these should betransported in proper containers. If a spillor leak should occur, immediately cleanand dry the area.

Use mud shields on your wheels. If youdrive on salted or gravel roads, mudshields help protect your vehicle. Full−sizeshields, which come as near to the groundas possible, are the best. We recommendthat the fittings and the area where theshields are installed be treated to resistcorrosion. Your Toyota dealer will behappy to assist in supplying and installingthe shields if they are recommended foryour area.

Keep your vehicle in a well ventilatedgarage or a roofed place. Do not parkyour vehicle in a damp, poorly venti-lated garage. If you wash your vehicle inthe garage, or if you drive it in coveredwith water or snow, your garage may beso damp it will cause corrosion. Even ifyour garage is heated, a wet vehicle cancorrode if the ventilation is poor.

Washing your Toyota

Keep your vehicle clean by regularwashing.

The following cases may cause weaknessto the paint or corrosion to the body andparts. Wash your vehicle as soon as pos-sible.

� When driving in a coastal area

� When driving on a road sprinkled withantifreeze

� When having coal tar, tree sap, birddroppings and carcass of an insect

� When driving in the areas where thereis a lot of smoke, soot, dust, iron dustand chemical substance

� When the vehicle becomes remarkablydirty with dust and mud

Hand−washing your Toyota

Work in the shade and wait until thevehicle body is not hot to the touch.

CAUTION

When cleaning under floor or chassis,be careful not to injure your hands.

1. Rinse off loose dirt with a hose. Re-move any mud or road salt from theunderside of the vehicle or in thewheel wells.

2. Wash with a mild car−wash soap,mixed according to the manufacturer’sinstructions. Use a soft cotton mitt andkeep it wet by dipping it frequently intothe wash water. Do not rub hard—letthe soap and water remove the dirt.

Plastic resin moon roof: Wash with a mildsoap or neutral detergent. Use a soft cot-ton towel or sponge. Do not use windowcleaner or abrasive cleaner. The plasticresin moon roof is easily damaged.

Plastic wheel ornaments: The plasticwheel ornaments are damaged easily byorganic substances. If any organic sub-stances splashes an ornament, be sure towash it off with water and check if theornament is damaged.

CAUTION

Do not attach the heavily damagedplastic wheel ornament. It may fly offthe wheel and cause accidents whilethe vehicle is moving.

Aluminum wheels: Use only a mild soapor neutral detergent.

Washing and waxing yourToyota


174 2002 MY CELICA_U (OM20792U)

Plastic bumpers: Wash carefully. Do notscrub with abrasive cleaners. The bumperfaces are soft.

Road tar: Remove with turpentine orcleaners that are marked safe for paintedsurfaces.

NOTICE

For plastic resin moon roof, plasticwheel ornaments, and plastic bump-ers:

Do not use organic substances (gaso-line, kerosene, benzine or strong sol-vents), which may be toxic or causedamage.

3. Rinse thoroughly—dried soap cancause streaking. In hot weather youmay need to rinse each section rightafter you wash it.

4. To prevent water spots, dry the vehicleusing a clean soft cotton towel. Do notrub or press hard—you might scratchthe paint.

Automatic car wash

Your vehicle may be washed in an auto-matic car wash, but remember that thepaint can be scratched by some type ofbrushes, unfiltered washing water, or thewashing process itself. Scratching reducespaint durability and gloss, especially ondarker colors. The manager of the carwash should be able to advise you wheth-er the process is safe for the paint onyour vehicle.

NOTICE

To prevent damage to the antenna,make sure it is removed before driv-ing your Toyota through an automaticcar wash.

Waxing your Toyota

Polishing and waxing is recommendedto maintain the original beauty of yourToyota’s finish.

Once a month or if the vehicle surfacedoes not repel water well, apply wax.

1. Always wash and dry the vehicle be-fore you begin waxing, even if you areusing a combined cleaner and wax.

2. Use a good quality polish and wax. Ifthe finish has become extremely weath-ered, use a car−cleaning polish, fol-lowed by a separate wax. Carefully fol-low the manufacturer’s instructions andprecautions. Be sure to polish and waxthe chrome trim as well as the paint.

3. Wax the vehicle again when waterdoes not bead but remains on the sur-face in large patches.

NOTICE

� Do not use wax on the plastic resinmoon roof. The plastic resin moonroof is easily damaged.

� Always remove the plastic bumpersif your vehicle is re−painted andplaced in a high heat paint waxingbooth. High temperatures coulddamage the bumpers.



CAUTION

� Vehicles with side airbags:

Be careful not to splash water orspill liquid on the floor. This mayprevent the side airbags from acti-vating correctly, resulting in seriousinjury.

� Do not wash the vehicle floor withwater, or allow water to get ontothe floor when cleaning the vehicleinterior or exterior. Water may getinto audio components or otherelectrical components above or un-der the floor carpet (or mat) andcause a malfunction; and it maycause body corrosion.

Vinyl interior

The vinyl upholstery may be easilycleaned with a mild soap or detergentand water.

First vacuum over the upholstery to re-move loose dirt. Then, using a sponge orsoft cloth, apply the soap solution to thevinyl. After allowing it to soak in for a fewminutes to loosen the dirt, remove the dirtand wipe off the soap with a clean dampcloth. If all the dirt do not come off, re-peat the procedure. Commercial foaming−type vinyl cleaners are also availablewhich work well. Follow the manufacturer’sinstructions.

NOTICE

Do not use solvent, thinner, gasolineor window cleaner on the interior.

Carpets

Use a good foam−type shampoo toclean the carpets.

Begin by vacuuming thoroughly to removeas much dirt as possible. Several types offoam cleaners are available; some are inaerosol cans and others are powders orliquids which you mix with water to pro-duce a foam. To shampoo the carpets,use a sponge or brush to apply the foam.Rub in overlapping circles.

Do not apply water—the best results areobtained by keeping the carpet as dry aspossible. Read the shampoo instructionsand follow them closely.

Seat belts

The seat belts may be cleaned withmild soap and water or with lukewarmwater.

Use a cloth or sponge. As you are clean-ing, check the belts for excessive wear,fraying, or cuts.

NOTICE

� Do not use dye or bleach on thebelts—it may weaken them.

� Do not use the belts until they be-come dry.

Cleaning the interior


176 2002 MY CELICA_U (OM20792U)

Windows

The windows may be cleaned with anyhousehold window cleaner.

NOTICE

When cleaning the inside of the win-dows, be careful not to scratch ordamage the heater wires on the rearwindow.

Air conditioning control panel, car au-dio, instrument panel, console panel,and switches

Use a soft damp cloth for cleaning.

Soak a clean soft cloth in water or luke-warm water then lightly wipe off dirt.

NOTICE

� Do not use organic substances (sol-vents, kerosene, alcohol, gasoline,etc.) or alkaline or acidic solutions.These chemicals can cause discol-oring, staining or peeling of thesurface.

� If you use cleaners or polishingagents, make sure their ingredientsdo not include the substances men-tioned above.

� If you use a liquid car freshener, donot spill the liquid onto the ve-hicle’s interior surfaces. It may con-tain the ingredients mentionedabove. Immediately clean any spillusing the method mentioned above.

Leather Interior

The leather upholstery may be cleanedwith neutral detergent for wool.

Remove dirt using a soft cloth dampenedwith 5% solution of neutral detergent forwool. Then thoroughly wipe off all tracesof detergent with a clean damp cloth.

After cleaning or whenever any part of theleather gets wet, dry with a soft cleancloth. Allow the leather to dry in a venti-lated shaded area.

NOTICE

� If a stain should fail to come outwith a neutral detergent, apply acleaner that does not contain anorganic solvent.

� Never use organic substances suchas benzine, alcohol or gasoline oralkaline or acid solutions for clean-ing the leather as these couldcause discoloring.

� Use of a nylon brush or syntheticfiber cloth, etc. may scratch thefine grained surface of the leather.

� Mildew may develop on soiled leath-er upholstery. Be especially carefulto avoid oil spots. Try to keep yourupholstery always clean.

� Long exposure to direct sunlightmay cause the leather surface toharden and shrink. Keep your ve-hicle in a shaded area, especially inthe summer.

� The interior of your vehicle is aptto heat up on hot summer days, soavoid placing on the upholsteryitems made of vinyl or plastic orcontaining wax as these tend tostick to leather when warm.

� Improper cleaning of the leather up-holstery could result in discolor-ation or staining.

If you have any questions about thecleaning of your Toyota, your localToyota dealer will be pleased to answerthem.



VEHICLE MAINTENANCE AND CAREMaintenance requirements 178. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General maintenance 179. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Does your vehicle need repairing? 181. . . . . . . . . . . . . . . . . . . . . . . . . . . . Emissions Inspection and Maintenance (I/M) programs 182. . . . . . . . .

For scheduled maintenance information, please refer to the separate “Sched-uled Maintenance Guide” or “Owner’s Manual Supplement”.

SECTION 6


178 2002 MY CELICA_U (OM20792U)

Your Toyota vehicle has been designed forfewer maintenance requirements with lon-ger service intervals to save both yourtime and money. However, each regularmaintenance, as well as day−to−day care,is more important than ever before to en-sure smooth, and trouble−free, safe, andeconomical driving.

It is the owner’s responsibility to makesure the specified maintenance, includinggeneral maintenance service, is performed.Note that both the new vehicle and emis-sion control system warranties specify thatproper maintenance and care must be per-formed. See “Owner’s Warranty Informa-tion Booklet” or “Owner’s Manual Supple-ment” for complete warranty information.

General maintenance

General maintenance items are those day−to−day care practices that are important toyour vehicle for proper operation. It is theowner’s responsibility to insure that thegeneral maintenance items are performedregularly.

These checks or inspections can be doneeither by yourself or a qualified technician,or if you prefer, your Toyota dealer will bepleased to do them at a nominal cost.

Scheduled maintenance

The scheduled maintenance items listed inthe “Scheduled Maintenance Guide” or“Owner’s Manual Supplement” are thoserequired to be serviced at regular inter-vals.

For details of your maintenance schedule,read the separate “Scheduled MaintenanceGuide” or “Owner’s Manual Supplement”.

It is recommended that any replacementparts used for maintenance or for therepair of the emission control systembe Toyota supplied.

The owner may elect to use non−Toyotasupplied parts for replacement pur-poses without invalidating the emissioncontrol system warranty. However, useof replacement parts which are not ofequivalent quality may impair the effec-tiveness of the emission control sys-tems.

You may also elect to have mainte-nance, replacement, or repair of theemission control devices and systemperformed by any automotive repair es-tablishment or individual without invali-dating this warranty. See “Owner’s War-ranty Information Booklet” or “Owner’sManual Supplement” for complete war-ranty information.

Where to go for service?

Toyota technicians are well−trained spe-cialists and are kept up to date with thelatest service information through technicalbulletins, service tips, and in−dealershiptraining programs. They learn to work onToyotas before they work on your vehicle,rather than while they are working on it.

You can be confident that your Toyotadealer’s service department performs thebest job to meet the maintenance require-ments on your vehicle—reliably and eco-nomically.

Your copy of the repair order is proof thatall required maintenance has been per-formed for warranty coverage. And if anyproblems should arise with your vehiclewhile under warranty, your Toyota dealerwill promptly take care of it. Again, besure to keep a copy of the repair orderfor any service performed on your Toyota.

What about do−it−yourself maintenance?

Many of the maintenance items are easyto do yourself if you have a little mechani-cal ability and a few basic automotivetools. Simple instructions for how to per-form them are presented in Section 7.

Maintenance requirements



If you are a skilled do−it−yourself mechan-ic, the Toyota service manuals are recom-mended. Please be aware that do−it−your-self maintenance can affect your warrantycoverage. See “Owner’s Warranty Informa-tion Booklet” or “Owner’s Manual Supple-ment” for the details.

Listed below are the general maintenanceitems that should be performed as fre-quently as specified. In addition to check-ing the items listed, if you notice anyunusual noise, smell or vibration, youshould investigate the cause or take yourvehicle to your Toyota dealer or a quali-fied service shop immediately. It is recom-mended that any problem you notice bebrought to the attention of your dealer orthe qualified service shop for their advice.

CAUTION

Make these checks only where ade-quate ventilation can be obtained ifyou run the engine.

OUTSIDE THE VEHICLE

Items listed below should be performedfrom time to time, unless otherwisespecified.

Tire pressureCheck the pressure with a gauge everytwo weeks, or at least once a month. SeeSection 7−2 for additional information.

Tire surface and wheel nutsCheck the tires carefully for cuts, damageor excessive wear. See Section 7−2 foradditional information. When checking thetires, make sure no nuts are missing, andcheck the nuts for looseness. Tightenthem if necessary.

Tire rotationRotate the tires according to the mainte-nance schedule. (For scheduled mainte-nance information, please refer to the“Scheduled Maintenance Guide” or “Own-er’s Manual Supplement”.) See Section7−2 for additional information.

Fluid leaksCheck underneath for leaking fuel, oil, wa-ter or other fluid after the vehicle hasbeen parked for a while. If you smell fuelfumes or notice any leak, have the causefound and corrected immediately.

Doors and engine hoodCheck that all doors including back dooroperate smoothly and all latches lock se-curely. Make sure the engine hood secon-dary latch secures the hood from openingwhen the primary latch is released.

General maintenance


180 2002 MY CELICA_U (OM20792U)

INSIDE THE VEHICLE

Items listed below should be checkedregularly, e.g. while performing periodicservices, cleaning the vehicle, etc.

LightsMake sure the headlights, stop lights, taillights, turn signal lights, and other lightsare all working.

Service reminder indicators and warningbuzzersCheck that all service reminder indicatorsand warning buzzers function properly.

Steering wheelBe alert for changes in steering condition,such as hard steering or strange noise.

SeatsCheck that all front seat controls such asseat adjusters, seatback recliner, etc. op-erate smoothly and that all latches locksecurely in any position. For folding−downrear seatbacks, check that the latcheslock securely.

Seat beltsCheck that the seat belt system such asbuckles, retractors and anchors operateproperly and smoothly. Make sure the beltwebbing is not cut, frayed, worn or dam-aged.

Accelerator pedalCheck the pedal for smooth operation anduneven pedal effort or catching.

Clutch pedalCheck the pedal for smooth operation.

Brake pedalCheck the pedal for smooth operation andthat the pedal has the proper clearance.Check the brake booster function.

BrakesAt a safe place, check that the brakes donot pull to one side when applied.

Parking brakeCheck that the lever has the proper traveland that, on a safe incline, your vehicleis held securely with only the parkingbrake applied.

Automatic transmission “Park” mecha-nismCheck the lock release button of the se-lector lever for proper and smooth opera-tion. On a safe incline, check that yourvehicle is held securely with the selectorlever in “P” position and all brakes re-leased.

IN THE ENGINE COMPARTMENT

Items listed below should be checkedfrom time to time, e.g. each time whenrefueling.

Washer fluidMake sure there is sufficient fluid in thetank. See Section 7−3 for additional infor-mation.

Engine coolant levelMake sure the coolant level is betweenthe “FULL” and “LOW” lines on the see−through reservoir when the engine is cold.See Section 7−2 for additional information.

Radiator, condenser and hosesCheck that the front of the radiator andcondenser are clean and not blocked withleaves, dirt, or insects. See in Section7−2 for additional information.

Battery electrolyte levelYour Toyota has a maintenance free bat-tery. You do not have to add distilled wa-ter. For longer life of the battery, however,see Section 7−3 for additional information.

Brake fluid levelMake sure the brake fluid level is correct.See Section 7−2 for additional information.



Engine oil levelCheck the level on the dipstick with theengine turned off and the vehicle parkedon a level spot. See Section 7−2 for addi-tional information.

Power steering fluid levelCheck the level through the reservoir. Thelevel should be in the “HOT” or “COLD”range depending on the fluid temperature.See Section 7−2 for additional information.

Exhaust systemIf you notice any change in the sound ofthe exhaust or smell exhaust fumes, havethe cause located and corrected immedi-ately. (See “Engine exhaust cautions” inSection 2.)

Be on the alert for changes in perfor-mance, sounds, and visual tip−offs thatindicate service is needed. Some impor-tant clues are as follows:

� Engine missing, stumbling, or pinging

� Appreciable loss of power

� Strange engine noises

� A leak under the vehicle (however, wa-ter dripping from the air conditioningafter use is normal.)

� Change in exhaust sound (This mayindicate a dangerous carbon monoxideleak. Drive with the windows open andhave the exhaust system checked im-mediately.)

� Flat−looking tire; excessive tire squealwhen cornering; uneven tire wear

� Vehicle pulls to one side when drivingstraight on a level road

� Strange noises related to suspensionmovement

� Loss of brake effectiveness; spongyfeeling brake or clutch pedal; pedal al-most touches floor; vehicle pulls to oneside when braking

� Engine coolant temperature continuallyhigher than normal

If you notice any of these clues, take yourvehicle to your Toyota dealer as soon aspossible. It probably needs adjustment orrepair.

CAUTION

Do not continue driving with the ve-hicle unchecked. It could result in se-rious vehicle damage and possiblypersonal injury.

Does your vehicle needrepairing?


182 2002 MY CELICA_U (OM20792U)

Some states have vehicle emission in-spection programs which include OBD(On−Board Diagnostics) checks.

The OBD system monitors the operationof the emission control system. When theOBD system determines that a problemexists somewhere in the emission controlsystem, the malfunction indicator lampcomes on. In this case, your vehicle maynot pass the I/M test and need to berepaired. Contact your Toyota dealer toservice the vehicle.

Even if the malfunction indicator lampdoes not come on, your vehicle may notpass the I/M test as readiness codeshave not been set in the OBD system.

Readiness codes are automatically setduring ordinary driving. However, when thebattery is disconnected or run down, thecodes are erased. Also, depending onyour driving habits, the codes may not becompletely set.

Also, if the malfunction indicator lamp hadcome on recently due to temporary mal-function such as a loose fuel tank cap,your vehicle may not pass the I/M test.

The malfunction indicator lamp will go offafter taking several driving trips, but theerror code in the OBD system will not becleared unless about 40 trips or more aretaken.

If your vehicle does not pass the I/M testeven the malfunction indicator lamp doesnot come on, contact your Toyota dealerto prepare the vehicle for re−testing.

Emissions Inspection andMaintenance (I/M) programs



DO−IT−YOURSELF MAINTENANCEIntroduction

Engine compartment overview 184. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuse locations 186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Do−it−yourself service precautions 187. . . . . . . . . . . . . . . . . . . . . . . . . . .

Positioning the jack 188. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts and tools 189. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7− 1


184 2002 MY CELICA_U (OM20792U)

1. Power steering fluid reservoir

2. Engine oil level dipstick

3. Engine coolant reservoir

4. Engine oil filler cap

5. Battery

6. Brake fluid reservoir

7. Fuse blocks

8. Radiator

9. Electric cooling fans

10. Condenser

11. Windshield and rear window washerfluid tank

Engine compartment overview�1ZZ−FE engine



1. Power steering fluid reservoir

2. Engine oil level dipstick

3. Engine coolant reservoir

4. Engine oil filler cap

5. Battery

6. Brake fluid reservoir

7. Fuse blocks

8. Radiator

9. Electric cooling fans

10. Condenser

11. Windshield and rear window washerfluid tank

�2ZZ−GE engine


186 2002 MY CELICA_U (OM20792U)

Spare fuses

Fuse locations



If you perform maintenance by yourself,be sure to follow the correct proceduregiven in this section.

You should be aware that improper or in-complete servicing may result in operatingproblems.

Performing do−it−yourself maintenanceduring the warranty period may affect yourwarranty coverage. Read the separateToyota Warranty statement for details andsuggestions.

This section gives instructions only forthose items that are relatively easy for anowner to perform. As explained in Section6, there are still a number of items thatmust be done by a qualified technicianwith special tools.

For information on tools and parts for do−it−yourself maintenance, see “Parts andtools”.

Utmost care should be taken when work-ing on your vehicle to prevent accidentalinjury. Here are a few precautions thatyou should be especially careful to ob-serve:

CAUTION

� When the engine is running, keephands, clothing, and tools awayfrom the moving fan and enginedrive belts. (Removing rings,watches, and ties is advisable.)

� Right after driving, the enginecompartment—the engine, radiator,exhaust manifold, power steeringfluid reservoir and spark plugboots, etc.—will be hot. So be care-ful not to touch them. Oil, fluidsand spark plugs may also be hot.

� If the engine is hot, do not removethe coolant reservoir cap or air re-lease valve or loosen the drainplugs to prevent burning yourself.

� Do not smoke, cause sparks or al-low open flames around fuel or thebattery. Their fumes are flammable.

� Do not get under your vehicle withjust the body jack supporting it. Al-ways use automotive jack stands orother solid supports.

� Be sure that the ignition is off ifyou work near the electric coolingfans or radiator grille. With theignition on, the electric cooling fanswill automatically start to run if theengine coolant temperature is highand/or the air conditioning is on.

� Use eye protection whenever youwork on or under your vehiclewhere you may be exposed to flyingor falling material, fluid spray, etc.

� Used engine oil contains potentiallyharmful contaminants which maycause skin disorders such as in-flammation or skin cancer, so careshould be taken to avoid prolongedand repeated contact with it. To re-move used engine oil from yourskin, wash thoroughly with soapand water.

� Do not leave used oil within thereach of children.

� Dispose of used oil and filter onlyin a safe and acceptable manner.Do not dispose of used oil and fil-ter in household trash, in sewers oronto the ground. Call your dealer ora service station for informationconcerning recycling or disposal.

Do−it−yourself serviceprecautions


188 2002 MY CELICA_U (OM20792U)

� Be extremely cautious when work-ing on the battery. It contains poi-sonous and corrosive sulfuric acid.


NOTICE

� Remember that battery and ignitioncables carry high currents or volt-ages. Be careful of accidentallycausing a short circuit.

� Add only demineralized or distilledwater to fill the radiator. And if youspill some of the coolant, be sureto wash it off with water to preventit from damaging the parts or paint.

� Do not allow dirt or anything elseto fall through the spark plug holes.

� Do not pry the outer electrode of aspark plug against the center elec-trode.

� Use only spark plugs of the speci-fied type. Using other types willcause engine damage, loss of per-formance or radio noise.

� Do not reuse iridium−tipped sparkplugs by cleaning or regapping.

� Do not overfill automatic transmis-sion fluid, or the transmissioncould be damaged.

� Do not drive with the air cleanerfilter removed, or excessive enginewear could result. Also backfiringcould cause a fire in the enginecompartment.

� Be careful not to scratch the glasssurface with the wiper frame.

� When closing the engine hood,check to see that you have not for-gotten any tools, rags, etc.

Front

Rear

Positioning the jack



When jacking up your vehicle with thejack, position the jack correctly asshown in the illustrations.

CAUTION

When jacking, be sure to observe thefollowing to reduce the possibility ofpersonal injury:

� Follow jacking instructions.

� Do not put any part of your bodyunder the vehicle supported by thejack. Personal injury may occur.

� Do not start or run the engine whileyour vehicle is supported by thejack.

� Stop the vehicle on a level firmground, firmly set the parking brakeand put the transmission in “P”(automatic) or reverse (manual).Block the wheels on the oppositeside of the jack up point if neces-sary.

� Make sure to set the jack properlyin the jack point. Raising the ve-hicle with jack improperly posi-tioned will damage the vehicle ormay allow the vehicle to fall off thejack and cause personal injury.

� Never get under the vehicle whenthe vehicle is supported by the jackalone.

� Do not raise the vehicle with some-one in the vehicle.

� When raising the vehicle, do notput an object on or under the jack.

NOTICE

Make sure to place the jack correctly,or your vehicle may be damaged.

Here is a list of parts and tools you willneed on performing do−it−yourself mainte-nance. Remember all Toyota parts are de-signed in metric sizes, so your tools mustbe metric.

CHECKING THE ENGINE OIL LEVEL

Parts (if level is low):

� Engine oil API grade SJ“Energy−Conserving”, SL“Energy−Conserving” or ILSACmultigrade having viscosity proper foryour climate

Tools:

� Rag or paper towel

� Funnel (only for adding oil)

CHECKING THE ENGINE COOLANT LEVEL


� “TOYOTA Long Life Coolant” or equiva-lentSee Section 7−2 for details about cool-ant type selection.

� Demineralized or distilled water

Tools:

� Funnel (only for adding coolant)

Parts and tools


190 2002 MY CELICA_U (OM20792U)

CHECKING BRAKE FLUID


� SAE J1703 or FMVSS No.116 DOT 3brake fluid

Tools:


� Funnel (only for adding fluid)

CHECKING POWER STEERING FLUID


� Automatic transmission fluidDEXRON�II or III

Tools:


� Funnel (only for adding fluid)

CHECKING BATTERY CONDITION

Tools:

� Warm water

� Baking soda

� Grease

� Conventional wrench (for terminalclamp bolts)

CHECKING AND REPLACING FUSES

Parts (if replacement is necessary):

� Fuse with same amperage rating asoriginal

ADDING WASHER FLUID

Parts:

� Water

� Washer fluid containing antifreeze (for winter use)

Tools:

� Funnel

REPLACING LIGHT BULBS

Parts:

� Bulb with same number and wattagerating as original (See charts in“Replacing light bulbs—” in Section7−3.)

Tools:

� Screwdriver



DO−IT−YOURSELF MAINTENANCEEngine and ChassisChecking the engine oil level 192. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the engine coolant levelel 193. . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the radiator and condenserr 194. . . . . . . . . . . . . . . . . . . . . . . . Checking brake fluid 195. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking power steering fluid 195. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking tire pressure 196. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking and replacing tires 197. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotating tires 198. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing snow tires and chains 199. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing wheels 200. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum wheel precautions 201. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7− 2


192 2002 MY CELICA_U (OM20792U)

Low level Full level

Add oil O.K. Too full

With the engine at operating tempera-ture and turned off, check the oil levelon the dipstick.

1. To get a true reading, the vehicleshould be on a level spot. After turningoff the engine, wait a few minutes forthe oil to drain back into the bottom ofthe engine.

2. Pull out the dipstick, and wipe it cleanwith a rag.

3. Reinsert the dipstick—push it in as faras it will go, or the reading will not becorrect.

4. Pull the dipstick out and look at the oillevel on the end.

CAUTION

Be careful not to touch the hot ex-haust manifold.

If the oil level is below or only slightlyabove the low level, add engine oil ofthe same type as already in the engine.

Remove the oil filler cap and add engineoil in small quantities at a time, checkingthe dipstick.

The approximate quantity of oil needed tofill between the low level and the full levelon the dipstick is indicated below for ref-erence.

When the level reaches within the correctrange, install the filler cap hand−tight.

Oil quantity, L (qt., lmp. qt.):

1ZZ−FE engine 1.3 (1.4, 1.1)2ZZ−GE engine 1.5 (1.6, 1.3)

NOTICE

� Avoid overfilling, or the enginecould be damaged.

� Check the oil level on the dipstickonce again after adding the oil.

ENGINE OIL SELECTION

Use API grade SJ “Energy−Conserving”,SL “Energy−Conserving” or ILSAC multi-grade engine oil.

Recommended viscosity (SAE):

5W-30 Preferred

Temperature range anticipated beforenext oil change

SAE 5W−30 is the best choice for yourvehicle, for good fuel economy, andgood starting in cold weather.

If you use SAE 10W−30 engine oil inextremely low temperatures, the enginemay become difficult to start, so SAE5W−30 engine oil is recommended.

Checking the engine oil level



API service symbol

ILSAC certification mark

Oil identification marks

Either or both API registered marks areadded to some oil containers to helpyou select the oil you should use.

The API Service Symbol is located any-where on the outside of the container.

The top portion of the label shows the oilquality by API (American PetroleumInstitute) designations such as SL. Thecenter portion of the label shows the SAEviscosity grade such as SAE 5W−30.“Energy−Conserving” shown in the lowerportion, indicates that the oil hasfuel−saving capabilities.

The ILSAC (International Lubricant Stan-dardization and Approval Committee) Certi-fication Mark is displayed on the front ofthe container.

Look at the see−through coolant reser-voir when the engine is cold. The cool-ant level is satisfactory if it is betweenthe “FULL” and “LOW” lines on thereservoir. If the level is low, have yourToyota dealer add ethylene−glycol typecoolant for proper corrosion protectionof aluminum components.

The coolant level in the reservoir will varywith engine temperature. However, if thelevel is on or below the “LOW” line, youshould have your Toyota dealer add cool-ant.

Always use ethylene−glycol type coolantfor a proper corrosion protection of alumi-num components. See information in thenext column.

If the coolant level drops within a shorttime after replenishing, there may be aleak in the system. Visually check theradiator, hoses, drain cock and waterpump.

If you can find no leak, have your Toyotadealer test the cap pressure and checkfor leaks in the cooling system.

Checking the engine coolantlevel


194 2002 MY CELICA_U (OM20792U)

CAUTION

To prevent burning yourself, do notremove the coolant reservoir cap orair release valve when the engine ishot.

Coolant type selection

Use of improper coolants may damageyour engine cooling system. Your coolantmust contain ethylene−glycol type coolantfor a proper corrosion protection of yourengine that contains aluminum compo-nents. Use “TOYOTA Long Life Coolant”or equivalent.

In addition to preventing freezing and sub-sequent damage to the engine, this typeof coolant will also prevent corrosion. Fur-ther supplemental inhibitors or additivesare neither needed nor recommended.

Read the coolant container for informationon freeze protection. Follow the manufac-turer’s directions for how much to mixwith plain water (preferably demineralizedwater or distilled water). The total capacityof the cooling system is given in Section8.

We recommend to use 50% solution foryour Toyota, to provide protection down toabout −35�C (−31�F). When it is extreme-ly cold, to provide protection down toabout −50�C (−58�F), 60% solution is rec-ommended. Do not use more than 70%solution for better coolant performance.

NOTICE


If any of the above parts are extremelydirty or you are not sure of their condi-tion, take your vehicle to Toyota dealer.

CAUTION

To prevent yourself from burning, becareful not to touch the radiator orcondenser when the engine is hot.

NOTICE

To prevent damage to the radiatorand condenser, do not perform thework by yourself.

Checking the radiator andcondenser



To check the fluid level, simply look atthe see−through reservoir. The levelshould be between the “MAX” and“MIN” lines on the reservoir.

It is normal for the brake fluid level to godown slightly as the brake pads wear. Sobe sure to keep the reservoir filled.

If the reservoir needs frequent refilling, itmay indicate a serious mechanical prob-lem.

If the level is low, add SAE J1703 orFMVSS No.116 DOT 3 brake fluid to thebrake reservoir.

Remove and replace the reservoir cap byhand. Fill the brake fluid to the dottedline. This brings the fluid to the correctlevel when you put the cap back on.

Use only newly opened brake fluid. Onceopened, brake fluid absorbs moisture fromthe air, and excess moisture can cause adangerous loss of braking.

CAUTION

Take care when filling the reservoirbecause brake fluid can harm youreyes and damage painted surfaces. Iffluid gets in your eyes, flush youreyes with clean water immediately. Ifyou still feel uncomfortable with youreyes, go to the doctor.

NOTICE

If you spill the fluid, be sure to washit off with water to prevent it fromdamaging the parts or paint.

If hotO.K.

Close

Open

If hot add

If cold add

If cold O.K.

Check the fluid level through the reser-voir. If necessary, add automatic trans-mission fluid DEXRON�II or III.

If the vehicle has been driven around 80km/h (50 mph) for 20 minutes (a littlemore in frigid temperatures), the fluid ishot (60°C—80°C or 140°F—175°F). Youmay also check the level when the fluidis cold (about room temperature,10°C—30°C or 50°F—85°F) if the enginehas not been run for about five hours.

Checking brake fluid Checking power steering fluid


196 2002 MY CELICA_U (OM20792U)

Clean all dirt from outside of the reservoirtank and look at the fluid level. If the fluidis cold, the level should be in the “COLD”range. Similarly, if it is hot, the fluid levelshould be in the “HOT” range. If the levelis at the low side of either range, addautomatic transmission fluid DEXRON�II orIII to bring the level within the range.

To remove the reservoir cap, turn it coun-terclockwise and lift up. To reinstall it,turn it clockwise. After replacing the reser-voir cap, visually check the steering boxcase, vane pump and hose connectionsfor leaks or damage.

CAUTION

The reservoir tank may be hot so becareful not to burn yourself.

NOTICE

Avoid overfilling, or the power steer-ing could be damaged.

Keep your tire pressures at the properlevel.

The recommended cold tire pressures, tiresize and the vehicle capacity weight aregiven in Section 8. They are also on thetire pressure label as shown.

You should check the tire pressures everytwo weeks, or at least once a month. Anddo not forget the spare!

Incorrect tire pressure can reduce tirelife and make your vehicle less safe todrive.

Low tire pressure results in excessivewear, poor handling, reduced fuel econo-my, and the possibility of blowouts fromoverheated tires. Also, low tire pressurecan cause poor sealing of the tire bead.If the tire pressure is excessively low,there is the possibility of wheel deforma-tion and/or tire separation.

High tire pressure produces a harsh ride,handling problems, excessive wear at thecenter of the tire tread, and a greaterpossibility of tire damage from road haz-ards.

If a tire frequently needs refilling, have itchecked by your Toyota dealer.

The following instructions for checkingtire pressure should be observed:

� The pressure should be checked onlywhen the tires are cold. If your ve-hicle has been packed for at least 3hours and has not been driven formore than 1.5 km or 1 mile since, youwill get an accurate cold tire pressurereading.

Checking tire pressure



� Always use a tire pressure gauge.The appearance of a tire can be mis-leading. Besides, tire pressures thatare even just a few pounds off candegrade ride and handling.

� Take special care when adding air tothe compact spare tire. The smallertire size can gain pressure very quick-ly. Add compressed air in small quanti-ties and check the pressure often untilit reaches the specified pressure.

� Do not bleed or reduce tire pressureafter driving. It is normal for the tirepressure to be higher after driving.

� Never exceed the vehicle capacityweight. The passenger and luggageweight should be located so that thevehicle is balanced.

� Be sure to reinstall the tire inflationvalve caps. Without the valve caps,dirt or moisture could get into the valvecore and cause air leakage. If the capshave been lost, have new ones put onas soon as possible.

Tread wear indicator

CHECKING YOUR TIRES

Check the tire tread for the tread wearindicators. If the indicators show, re-place the tires.

The tires on your Toyota have built−intread wear indicators to help you knowwhen the tires need replacement. Whenthe tread depth wears to 1.6 mm (0.06in.) or less, the indicators will appear. Ifyou can see the indicators in two or moreadjacent grooves, the tire should be re-placed. The lower the tread, the higherthe risk of skidding.

The effectiveness of snow tires is lostif the tread wears down below 4 mm(0.16 in.).

Check the tires regularly for damagesuch as cuts, splits and cracks. If anydamage is found, consult with a techni-cian and have the tire repaired or re-placed.

Even if the damage does not appear seri-ous, a qualified technician should examinethe damage. Objects which have pene-trated the tire may have caused internaldamage.

Any tires which are over 6 years oldmust be checked by a qualified techni-cian even if damage is not obvious.

Tires deteriorate with age even if theyhave never or seldom been used.

This also applies to the spare tire andtires stored for future use.

REPLACING YOUR TIRES

When replacing a tire, use only thesame size and construction as original-ly installed and with the same or great-er load capacity.

Using any other size or type of tire mayseriously affect handling, ride, speedome-ter/odometer calibration, ground clearance,and clearance between the body and tiresor snow chains.

Checking and replacing tires


198 2002 MY CELICA_U (OM20792U)

CAUTION

� Do not mix radial, bias belted, orbias−ply tires on your vehicle. Itcan cause dangerous handling char-acteristics, resulting in loss of con-trol.

� Do not use tires or wheels otherthan the manufacturer’s recom-mended size.

Toyota recommends all four tires, or atleast both front or rear tires be re-placed as a set.

See “If you have a flat tire” in Section 4for tire change procedure.

When a tire is replaced, the wheelshould always be balanced.

An unbalanced wheel may affect vehiclehandling and tire life. Wheels can get outof balance with regular use and shouldtherefore be balanced occasionally.

When replacing a tubeless tire, the airvalve should also be replaced with anew one.

Turning direction

Turning direction indicator (type A)

Turning direction

Turning direction indicator (type B)

If a turning indicator is marked on yourtires, you have uni−directional tires. Be-fore rotating, check whether your tiresare uni−directional before rotating them.Using tires on the wrong side of thevehicle will impair tire performance.

See the following instructions for how torotate your tires correctly.

Rotating tires



Without uni−directional tires (with a spare tire of the same wheel typeas the installed tires)

Others

To equalize the wear and help extendtire life, Toyota recommends that yourotate your tires according to the main-tenance schedule. (For scheduled main-tenance information, please refer to the“Scheduled Maintenance Guide” or“Owner’s Manual Supplement”.) Howev-er, the most appropriate timing for tirerotation may vary according to yourdriving habits and road surface condi-tions.

See “If you have a flat tire” in Section 4for tire change procedure.

When rotating tires, check for unevenwear and damage. Abnormal wear is usu-ally caused by incorrect tire pressure, im-proper wheel alignment, out−of−balancewheels, or severe braking.

CAUTION

Do not include a compact spare tirewhen rotating the tires. It is designedfor temporary use only.

WHEN TO USE SNOW TIRES ORCHAINS

Snow tires or chains are recommendedwhen driving on snow or ice.

On wet or dry roads, conventional tiresprovide better traction than snow tires.

SNOW TIRE SELECTION

If you need snow tires, select the samesize, construction and load capacity asthe original tires on your Toyota.

Do not use tires other than those men-tioned above. Do not install studded tireswithout first checking local regulations forpossible restrictions.

SNOW TIRE INSTALLATION

Snow tires should be installed on allwheels.

Installing snow tires on the front wheelsonly can lead to an excessive differencein road grip capability between the frontand rear tires which could cause loss ofvehicle control.

When storing removed tires, you shouldstore them in a cool dry place.

Mark the direction of rotation and be sureto install them in the same direction whenreplacing.

Installing snow tires andchains


200 2002 MY CELICA_U (OM20792U)

CAUTION

� Do not drive with the snow tiresincorrectly inflated.

� Never drive over 120 km/h (75 mph)with any type of snow tires.

TIRE CHAIN SELECTION

Use the tire chains of correct size andtype.

Use SAE Class “S” type radial tire chainsexcept radial cable chains or V−bar typechains.

Regulations regarding the use of tirechains vary according to location ortype of road, so always check thembefore installing chains.

CHAIN INSTALLATION

Install the chains on the front tires astightly as possible. Do not use tirechains on the rear tires. Retightenchains after driving 0.5—1.0 km(1/4—1/2 mile).

When installing chains on your tires, care-fully follow the instructions of the chainmanufacturer.

If wheel covers are used, they will bescratched by the chain band, so removethe covers before putting on the chains.

CAUTION

� Do not exceed 50 km/h (30 mph) orthe chain manufacturer’s recom-mended speed limit, whichever islower.

� Drive carefully avoiding bumps,holes, and sharp turns, which maycause the vehicle to bounce.

� Avoid sharp turns or locked−wheelbraking, as use of chains may ad-versely affect vehicle handling.

� When driving with chains installed,be sure to drive carefully. Slowdown before entering the curves toavoid losing control of the vehicle.Otherwise an accident may occur.

NOTICE

Do not attempt to use a tire chain onthe compact spare tire, as it may re-sult in damage to the vehicle as wellas the tire.

WHEN TO REPLACE YOUR WHEELS

If you have wheel damage such asbending, cracks or heavy corrosion, thewheel should be replaced.

If you fail to replace damaged wheels, thetire may slip off the wheel or cause lossof handling control.

WHEEL SELECTION

When replacing wheels, care should betaken to ensure that the wheels are re-placed by ones with the same load ca-pacity, diameter, rim width, and offset.

This must be observed on compact sparetires, too.

Correct replacement wheels are availableat your Toyota dealer.

A wheel of a different size or type mayadversely affect handling, wheel and bear-ing life, brake cooling, speedometer/odom-eter calibration, stopping ability, headlightaim, bumper height, vehicle ground clear-ance, and tire or snow chain clearance tothe body and chassis.

Replacing wheels



Replacement with used wheels is not rec-ommended as they may have been sub-jected to rough treatment or high mileageand could fail without warning. Also, bentwheels which have been straightened mayhave structural damage and thereforeshould not be used. Never use an innertube in a leaking wheel which is designedfor a tubeless tire.

� When installing aluminum wheels,check that the wheel nuts are tightafter driving your vehicle the first 1600km (1000 miles).

� If you have rotated, repaired, orchanged your tires, check that thewheel nuts are still tight after driving1600 km (1000 miles).

� When using tire chains, be careful notto damage the aluminum wheels.

� Use only the Toyota wheel nuts andwrench designed for your aluminumwheels.

� When balancing your wheels, use onlyToyota balance weights or equivalentand a plastic or rubber hammer.

� As with any wheel, periodically checkyour aluminum wheels for damage. Ifdamaged, replace immediately.

Aluminum wheel precautions


202 2002 MY CELICA_U (OM20792U)



DO−IT−YOURSELF MAINTENANCEElectrical componentsChecking battery condition 204. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery recharging precautions 205. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking and replacing fuses 206. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Adding washer fluid 207. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing light bulbs 208. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 7− 3


204 2002 MY CELICA_U (OM20792U)

CAUTION

BATTERY PRECAUTIONS

The battery produces flammable andexplosive hydrogen gas.

� Do not cause a spark from the bat-tery with tools.

� Do not smoke or light a match nearthe battery.

The electrolyte contains poisonousand corrosive sulfuric acid.

� Avoid contact with eyes, skin orclothes.

� Never ingest electrolyte.

� Wear protective safety glasses whenworking near the battery.

� Keep children away from the bat-tery.

EMERGENCY MEASURES

� If electrolyte gets in your eyes,flush your eyes with clean waterimmediately and get immediatemedical attention. If possible, con-tinue to apply water with a spongeor cloth while en route to the medi-cal office.

� If electrolyte gets on your skin,thoroughly wash the contact area. Ifyou feel pain or burning, get medi-cal attention immediately.

� If electrolyte gets on your clothes,there is a possibility of its soakingthrough to your skin, so immediate-ly take off the exposed clothing andfollow the procedure above, if nec-essary.

� If you accidentally swallow electro-lyte, drink a large quantity of wateror milk. Follow with milk of magne-sia, beaten raw egg or vegetableoil. Then go immediately for emer-gency help.


Terminals Groundcable

Hold−down clamp

Check the battery for corroded or looseterminal connections, cracks, or loosehold−down clamp.

a. If the battery is corroded, wash it offwith a solution of warm water and bak-ing soda. Coat the outside of the termi-nals with grease to prevent further cor-rosion.

b. If the terminal connections are loose,tighten their clamp nuts—but do notovertighten.

c. Tighten the hold−down clamp onlyenough to keep the battery firmly inplace. Overtightening may damage thebattery case.

Checking battery condition——Precautions —Checking battery exterior



NOTICE

� Be sure the engine and all accesso-ries are off before performing main-tenance.

� When checking the battery, removethe ground cable from the negativeterminal (“−” mark) first and rein-stall it last.

� Be careful not to cause a short cir-cuit with tools.

� Take care no solution gets into thebattery when washing it.

Type A

Green DarkClear or light yellow

Type B

Blue White Red

CHECKING BY INDICATOR

Check the battery condition by the indi-cator color.

Indicator colorCondition

Type A Type B

Green Blue Good

Dark White

Chargingnecessary. Havebattery checkedby your Toyotadealer.

Clear orlight

yellowRed

Have batterychecked by yourToyota dealer.

During recharging, the battery is pro-ducing hydrogen gas.

Therefore, before recharging:

1. If recharging with the battery installedon the vehicle, be sure to disconnectthe ground cable.

2. Be sure the power switch on the re-charger is off when connecting thecharger cables to the battery and whendisconnecting them.

CAUTION

� Always charge the battery in an un-confined area. Do not charge thebattery in a garage or closed roomwhere there is not sufficient ventila-tion.

� Only do a slow charge (5 A orless). Charging at a quicker rate isdangerous. The battery may ex-plode, causing personal injuries.

NOTICE

Never recharge the battery while theengine is running. Also, be sure allaccessories are turned off.

—Checking battery condition Battery recharging precautions


206 2002 MY CELICA_U (OM20792U)

Good Blown

Type A

Good Blown

Type B

Good Blown

Type C

Good Blown

Type D

If the headlights or other electricalcomponents do not work, check thefuses. If any of the fuses are blown,they must be replaced.

See “Fuse locations” in Section 7−1 forlocations of the fuses.

Turn the ignition switch and inoperativecomponent off. Pull a suspected fusestraight out and check it.

Determine which fuse may be causing theproblem. The lid of the fuse box showsthe name of the circuit for each fuse. SeeSection 8 of this manual for the functionscontrolled by each circuit.

Type A fuses can be pulled out by thepull−out tool. The location of the pull−outtool is shown in the illustration.

Checking and replacing fuses



If you are not sure whether the fuse hasblown, try replacing the suspected fusewith one that you know is good.

If the fuse has blown, push a new fuseinto the clip.

Only install a fuse with the amperage rat-ing designated on the fuse box lid.

If you do not have a spare fuse, in anemergency you can pull out the “RADIO”,“CIG” or “HTR” fuse, which may be dis-pensable for normal driving, and use it ifits amperage rating is the same.

If you cannot use one of the same amper-age, use one that is lower, but as closeas possible to the rating. If the amperageis lower than that specified, the fusemight blow out again but this does notindicate anything wrong. Be sure to getthe correct fuse as soon as possible andreturn the substitute to its original clip.

It is a good idea to purchase a set ofspare fuses and keep them in your ve-hicle for emergencies.

If the new fuse immediately blows out,there is a problem with the electrical sys-tem. Have your Toyota dealer correct it assoon as possible.

CAUTION

Never use a fuse with a higher am-perage rating, or any other object, inplace of a fuse. This may cause ex-tensive damage and possibly a fire.

If any washer does not work, the wash-er tank may be empty. Check the wash-er fluid level on the level gauge. If thewasher fluid level is below “LOW”, addwasher fluid.

You may use plain water as washer fluid.However, in cold areas where tempera-tures range below freezing point, usewasher fluid containing antifreeze. Thisproduct is available at your Toyota dealerand most auto parts stores. Follow themanufacturer’s directions for how much tomix with water.

Adding washer fluid


208 2002 MY CELICA_U (OM20792U)

NOTICE

Do not use engine antifreeze or anyother substitute because it may dam-age your vehicle’s paint.

The following illustrations show how togain access to the bulbs. When replacinga bulb, make sure the ignition switch andlight switch are off. Use bulbs with thewattage ratings given in the table.

CAUTION

� To prevent yourself from burning,do not replace the light bulbs whilethey are hot.

� Halogen bulbs have pressurized gasinside and require special handling.They can burst or shatter ifscratched or dropped. Hold a bulbonly by its plastic or metal case.Do not touch the glass part of abulb with bare hands.

The inside of the lens of exterior lightssuch as headlights may temporarily fog upwhen the lens becomes wet in the rain orin a car wash. This is not a problembecause the fogging is caused by thetemperature difference between the outsideand inside of the lens, just like thewindshield fogged up in the rain. However,if there is a large drop of water on theinside of the lens, or if there is waterpooled inside the light, contact yourToyota dealer.

NOTICE

Only use a bulb of the listed type.

Light bulbs BulbNo.

W Type

Headlights (low beam)

— 55 A

Headlights (high beam)

9005 65 B

Front fog light — 55 C

Parking lights — 5 D

Front turn signallights

— 21 E

Front side markerlights

— 5 D

Rear turn signallights

— 21 D

Stop/tail lights — 21/5 D

Back−up lights — 18 D

License plate lights — 5 D

Interior light(with moon roof)

— 10 E

Interior light (without moon roof)

— 8 F

Replacing light bulbs—



Light bulbs BulbNo.

W Type

Glove box light — 1.2 D

Luggagecompartment light

— 5 F

A: H7 halogen bulbsB: HB3 halogen bulbsC: H3 halogen bulbsD: Wedge base bulbsE: Single end bulbsF: Double end bulbs

1. Open the hood.

RIGHT SIDE HEADLIGHT—Remove theclips and take out the cover. In doingso, remove the washer hose from thenotch on the cover.

Remove and install the cover clips asshown in the following illustrations.

—Headlights (low beam)


210 2002 MY CELICA_U (OM20792U)

Removing clip

Installing clip

2. Unplug the connector. Remove therubber cover.

If the connector is tight, wiggle it.

3. Release the bulb retaining springand remove the bulb along with thesocket. Install a new bulb into thesocket and return the bulb retainingspring to its original position.

To install a bulb, align the tabs of thebulb with the cutout of the mounting hole.



4. Install the rubber cover with the“TOP” mark upward, and snuggle onthe boss. Plug in the connector.

Make sure the rubber cover fits snugly onthe connector and the headlight body.

Aiming is not necessary after replacingthe bulb. When aiming adjustment is nec-essary, contact your Toyota dealer.

5. RIGHT SIDE HEADLIGHT—Install thecover.

NOTICE

Always notch the washer hose beforefastening it when installing the cover.This prevents washer hose damage.

—Headlights (high beam)


212 2002 MY CELICA_U (OM20792U)

1. Open the hood.

RIGHT SIDE HEADLIGHT—Remove theclips and take out the cover. In doingso, remove the washer hose from thenotch on the cover.

Remove and install the cover clips asshown in the following illustrations.

Removing clip

Installing clip

2. Turn the bulb base counterclockwiseand remove it.



3. Pull the bulb out of the bulb baseand install a new bulb.

If the connector is tight, wiggle it.

4. Insert the bulb base into the mount-ing hole by turning it clockwise.

Aiming is not necessary after replacingthe bulb. When aiming adjustment is nec-essary, contact your Toyota dealer.

5. RIGHT SIDE HEADLIGHT—Install thecover.

NOTICE



214 2002 MY CELICA_U (OM20792U)

If either the left or right front fog orfront side marker lights burns out, con-tact your Toyota dealer.

NOTICE

Do not try to replace the front fog orfront side marker light bulbs by your-self. You may damage the vehicle.

RIGHT SIDE PARKING LIGHT—Removeand install the clips as shown in thefollowing illustrations.

NOTICE


—Front fog and front sidemarker lights —Parking lights



Removing clip

Installing clip

—Front turn signal lights


216 2002 MY CELICA_U (OM20792U)

RIGHT SIDE FRONT TURN SIGNALLIGHT—Remove and install the clips asshown in the following illustrations.

NOTICE


Removing clip

Installing clip



Remove the cover. a: Stop/tail lightb: Back−up lightc: Rear turn signal light

Use a Phillips−head screwdriver.

Remove the cover.

—Rear turn signal, stop/tail,and back−up lights —License plate lights


218 2002 MY CELICA_U (OM20792U)



SPECIFICATIONSDimensions and weight 220. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Engine 220. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuel 220. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service specifications 221. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tires 223. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Fuses 224. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 8


220 2002 MY CELICA_U (OM20792U)

Overall length mm (in.) 4330 (170.5)

Overall width mm (in.) 1735 (68.3)

Overall height mm (in.) 1305 (51.8)∗

Wheelbase mm (in.) 2600 (102.4)

Front tread mm (in.) 1490 (58.7)

Rear tread mm (in.) 1480 (58.3)

Vehicle capacity weight(occupants + luggage)

kg (lb.) 329 (725)∗: Unladen vehicle

Model: 1ZZ−FE and 2ZZ−GE

Type: 4 cylinder in line, 4 cycle, gasoline

Bore and stroke, mm (in.): 1ZZ−FE engine

79.0 � 91.5 (3.11 � 3.60)2ZZ−GE engine

82.0 � 85.0 (3.23 � 3.35)

Displacement, cm3 (cu. in.):1ZZ−FE engine 1794 (109.5)2ZZ−GE engine 1796 (109.6)

Fuel type:

1ZZ−FE engineUnleaded gasoline, Octane Rating 87(Research Octane Number 91) orhigher

2ZZ−GE engineSelect premium unleaded gasoline withan Octane Rating of 91 (Research Oc-tane Number 96) or higher for opti-mum engine performance

Fuel tank capacity, L (gal., Imp. gal.): 55 (14.5, 12.1)

Dimensions and weight Engine Fuel



ENGINE

Valve clearance (engine cold), mm (in.):

1ZZ−FE engineIntake 0.15—0.25 (0.006—0.010)Exhaust 0.25—0.35 (0.010—0.014)

2ZZ−GE engine (on a roller side)Intake 0.08—0.18 (0.003—0.007)Exhaust 0.22—0.32 (0.009—0.013)

Spark plug type:

1ZZ−FE engineDENSO SK16R11NGK IFR5A11

2ZZ−GE engineDENSO SK20R11NGK IFR6A11

Spark plug gap, mm (in.):1.1 (0.043)

ENGINE LUBRICATION

Oil capacity (drain and refill), L (qt., Imp. qt.):

1ZZ−FE engineWith filter 3.7 (3.9, 3.3)Without filter 3.5 (3.7, 3.1)

2ZZ−GE engineWith filter 4.4 (4.8, 4.0)Without filter 4.2 (4.6, 3.8)

Oil grade:API grade SJ “Energy−Conserving”, SL“Energy−Conserving” or ILSAC multi-grade engine oil is recommended.

Recommended oil viscosity (SAE):

5W-30 Preferred

Temperature range anticipated beforenext oil change

COOLING SYSTEM

Total capacity, L (qt., Imp. qt.):

1ZZ−FE engineManual transaxle 5.7 (6.0, 5.0)Automatic transaxle 5.6 (5.9, 4.9)

2ZZ−GE engineManual transaxle 5.9 (6.2, 5.2)Automatic transaxle 5.8 (6.1, 5.1)

Coolant type:

“TOYOTA Long Life Coolant” or equiva-lent

With ethylene−glycol type coolant for aproper corrosion protection of aluminumcomponents


BATTERY

Open voltage∗ at 20°C (68°F):

12.6—12.8 V Fully charged12.2—12.4 V Half charged11.8—12.0 V Discharged

∗: Voltage that is checked 20 minutes af-ter the key is removed with all the lightsturned off

Charging rates:5 A max.

Service specifications


222 2002 MY CELICA_U (OM20792U)

CLUTCH

Pedal free play, mm (in.):5—15 (0.2—0.6)

Fluid type:SAE J1703 or FMVSS No.116 DOT 3

MANUAL TRANSAXLE

Oil capacity, L (qt., Imp. qt.):1ZZ−FE engine

1.9 (2.0, 1.7)2ZZ−GE engine

2.3 (2.4 2.0)

Oil type: Gear oil API GL−4 or GL−5

Recommended oil viscosity:SAE 75W−90

AUTOMATIC TRANSAXLE

Fluid capacity (drain and refill), L (qt., Imp. qt.):

1ZZ−FE engineUp to 2.9 (3.1, 2.6)

2ZZ−GE engineUp to 4.0 (4.2, 3.5)

Fluid type:Automatic transmission fluid Type T−IV

Change automatic transmission fluid onlyas necessary.

Generally, it is necessary to change auto-matic transmission fluid only if your ve-hicle is driven under one of the SpecialOperating Conditions listed in your“Scheduled Maintenance Guide” or “Own-er’s Manual Supplement”. When changingthe automatic transmission fluid, use onlyToyota Genuine ATF Type T−IV (ATFJWS3309 or NWS6500) to aid in assuringoptimum transaxle performance.

Notice: Using automatic transmissionfluid other than Toyota Genuine ATFType T−IV may cause deterioration inshift quality, locking up of your trans-mission accompanied by vibration, andultimately damage the automatic trans-mission of your vehicle.

BRAKES

Minimum pedal clearance when depressedwith the force of 490 N (50 kgf, 110 lbf)with the engine running, mm (in.):

85 (3.4)

Pedal free play, mm (in.): 1—6 (0.04—0.24)

Pad wear limit, mm (in.): 1.0 (0.04)

Lining wear limit, mm (in.): 1.0 (0.04)

Parking brake adjustment when pulled withthe force of 196 N (20 kgf, 44 lbf):

7—8 clicks

Fluid type: SAE J1703 or FMVSS No.116 DOT 3

STEERING

Wheel free play: Less than 30 mm (1.2 in.)

Power steering fluid type: Automatic transmission fluid DEXRON�IIor III



Tire size and pressure:

Except spare tire

Model Tire size

Tire pressurekPa (kgf/cm2 or bar, psi) Wheel size

Front Rear

1ZZ−FE engine195/60R15 88H 210 (2.1, 29) 210 (2.1, 29) 15 � 6 1/2JJ

P195/60R15 87H 210 (2.1, 29) 210 (2.1, 29) 15 � 6 1/2JJ

2ZZ−GE engine

205/55R15 87V 220 (2.2, 32) 220 (2.2, 32) 15 � 6 1/2JJ

P205/55R15 87V 220 (2.2, 32) 220 (2.2, 32) 15 � 6 1/2JJ

205/50R16 87V 220 (2.2, 32) 220 (2.2, 32) 16 � 6 1/2JJ

Spare tire

Tire size Tire pressure kPa (kgf/cm2 or bar, psi) Wheel size

U.S.A T125/70D16 96M 420 (4.2, 60) 16 � 4T

Canada Same as original tire

Wheel nut torque, N·m (kgf·m, ft·Ibf):103 (10.5, 76)

NOTE: For a complete information on tires (e.g. replacing tires or replacing wheels), see “Checking tire pressure” through “Aluminumwheel precautions” in Section 7−2.

Tires


224 2002 MY CELICA_U (OM20792U)

Engine compartment

Fuses (type A)

1. HEAD LH LWR 10 A: Left−hand head-light (low beam)

2. ABS NO.2 25 A: Anti−lock brake sys-tem

3. HEAD RH UPR 20 A: Right−handheadlight (high beam)

4. DRL NO.1 7.5 A: Daytime running lightsystem

5. HEAD RH LWR 10 A: Right−handheadlight (low beam)

6. HEAD LH UPR 10 A: Left−hand head-light (high beam)

Engine compartment

7. IG2 15 A: Starting system, multiportfuel injection system/sequential multi-port fuel injection system

8. HAZ 10 A: Emergency flashers, turnsignal lights

9. ST 7.5 A: Starting system, multiportfuel injection system/sequential multi-port fuel injection system

10. AM2 7.5 A: Starting system

11. SPARE 10 A: Spare fuse

12. EFI NO.2 7.5 A: Multiport fuel injectionsystem/sequential multiport fuel injec-tion system, emission control system

Instrument panel

13. EFI 15 A: Multiport fuel injection sys-tem/sequential multiport fuel injectionsystem, “EFI NO.1” and “EFI NO.2”fuses


15. EFI NO.1 7.5 A: Multiport fuel injectionsystem/sequential multiport fuel injec-tion system

16. DCC 25 A: “RADIO”, “DOME”, “MPX−B” and “ECU−B” fuses


18. HORN 10 A: Horn

19. ALT−S 7.5 A: Charging system

Fuses



20. HEAD RH UPR 10 A: Right−handheadlight (high beam), daytime runninglight system

21. HEAD LH UPR 10 A: Left−hand head-light (high beam)

22. S/ROOF 15 A: Electric moon roof

23. CIG 15 A: Cigarette lighter

24. FL P/W 20 A: Power windows

25. AM1 25 A: Starting system, “CIG”,“ECU ACC”, “SRS−IG”, “WASHER”,“WIPER”, “BK/UP LP”, “TENS RDC”,“DEF RLY”, “BODY ECU−IG”, “TURN”,“HTR”, “WARNING”, “FAN RLY”, “ABS−IG” and “ECU−IG” fuses

26. STOP 10 A: Stop lights, anti−lockbrake system, high mounted stoplight,multiport fuel injection system/sequen-tial multiport fuel injection system, elec-tronically controlled automatic transmis-sion system, cruise control system

27. DOOR 20 A: Power door lock system

28. SRS−IG 7.5 A: SRS airbag system

29. FR FOG 15 A: Front fog lights

30. WASHER 15 A: Windshield wipers andwasher, rear window wiper and washer

31. OBD 7.5 A: On−board diagnosis sys-tem

32. RADIO 15 A: Car audio system

33. WIPER 25 A: Windshield wipers andwasher

34. TURN 7.5 A: Turn signal lights

35. MIR HTR 10 A: No circuit

36. HTR 10 A: Air conditioning system

37. RR WIPER 15 A: Rear window wiperand washer

38. TAIL 10 A: Tail lights, instrument panellights, license plate lights, front sidemaker lights

39. FR P/W 20 A: Power windows

Fuses (type B)

40. SPARE 7.5 A: Spare fuse

41. a. MPX−B 7.5 A: Wireless remote con-trol system

b. RR FOG 7.5 A: No circuitc. DOME 7.5 A: Clock, interior lightd. ECU−B 7.5 A: Air conditioning sys-

tem, gauges and meters

42. a. WARNING 5 A: Charging system,gauges and meters

b. ECU−IG 5 A: Cruise control systemc. ABS−IG 5 A: Anti−lock brake sys-

tem d. FAN RLY 5 A: Electric coolingfan

43. a. PANEL1 7.5 A: Car audio system,cigarette lighter, glove box light

b. PANEL2 7.5 A: Gauges and meters,air conditioning system, electronical-ly controlled automatic transmissionsystem, headlight beam level controlsystem, front fog lights, emergencyflasher, turn signal lights

c. ECU−ACC 7.5 A: Clock, car audiosystem, power rear view mirror con-trols

44. a. BK/UP LP 5 A: Back−up lightsb. DEF RLY 5 A: Power windows, rear

window defoggerc. BODY ECU−IG 5 A: Multiplex com-

munication systemd. TENS RDC 5 A: Electronically con-

trolled automatic transmission sys-tem, shift lock control system, elec-tric moon roof

Fuses (type C)

45. CDS 30 A: Electric cooling fan

46. MAIN 40 A: Starting system, daytimerunning light system

47. ABS NO.1 40 A: Anti−lock brake sys-tem

48. RDI 30 A: Electric cooling fan

49. HTR 50 A: Air conditioning system

50. DEF 30 A: Rear window defogger


226 2002 MY CELICA_U (OM20792U)

Fuses (type D)

51. ALT 120 A: Cooling system, electriccooling fan, starting system, rear win-dow defogger, tail lights, “ABS NO.1”,“ABS NO.2”, “HTR”, “FR P/W”, “FLP/W”, “DOOR”, “OBD”, “STOP”, “S/ROOF”, “MIR HTR”, “FR FOG” and“AM1” fuses



REPORTING SAFETY DEFECTS FOR U.S.OWNERS AND UNIFORM TIRE QUALITYGRADINGReporting safety defects for U.S. ownersrs 228. . . . . . . . . . . . . . . . . . . . . Uniform tire quality grading 228. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

SECTION 9


228 2002 MY CELICA_U (OM20792U)

If you believe that your vehiclehas a defect which could cause acrash or could cause injury ordeath, you should immediately in-form the National Highway TrafficSafety Administration (NHTSA) inaddition to notifying Toyota MotorSales, U.S.A., Inc. (Toll−free: 1−800−331−4331).

If NHTSA receives similar com-plaints, it may open an investiga-tion, and if it finds that a safetydefect exists in a group of ve-hicles, it may order a recall andremedy campaign. However,NHTSA cannot become involvedin individual problems betweenyou, your dealer, or Toyota MotorSales, U.S.A., Inc.

To contact NHTSA, you may ei-ther call the Auto Safety Hotlinetoll−free at 1−800−424−9393 (or366−0123 in Washington, D.C.area) or write to: NHTSA, U.S.Department of Transportation,Washington, D.C. 20590. You canalso obtain other information aboutmotor vehicle safety from the Hot-line.

This information has been prepared in ac-cordance with regulations issued by theNational Highway Traffic Safety Adminis-tration of the U.S. Department of Trans-portation. It provides the purchasers and/or prospective purchasers of Toyotavehicles with information on uniform tirequality grading.

Your Toyota dealer will help answer anyquestions you may have as you read thisinformation.

DOT quality grades—All passenger cartires must conform to Federal SafetyRequirements in addition to thesegrades. Quality grades can be foundwhere applicable on the tire sidewallbetween tread shoulder and maximumsection width. For example: Treadwear200 Traction AA Temperature A

Reporting safety defects forU.S. owners Uniform tire quality grading



Treadwear—The treadwear grade is acomparative rating based on the wear rateof the tire when tested under controlledconditions on a specified government testcourse. For example, a tire graded 150would wear one and a half (1 1/2) timesas well on the government course as atire graded 100. The relative performanceof tires depends upon the actual condi-tions of their use, however, and may de-part significantly from the norm due tovariations in driving habits, service prac-tices and differences in road characteris-tics and climate.

Traction AA, A, B, C—The tractiongrades, from highest to lowest, are AA, A,B, and C, and they represent the tire’sability to stop on wet pavement as mea-sured under controlled conditions on spe-cified government test surfaces of asphaltand concrete. A tire marked C may havepoor traction performance.

Warning: The traction grade assigned tothis tire is based on braking (straightahead) traction tests and does not includecornering (turning) traction.

Temperature A, B, C—The temperaturegrades are A (the highest), B, and C,representing the tire’s resistance to thegeneration of heat and its ability to dissi-pate heat when tested under controlledconditions on a specified indoor laboratorytest wheel. Sustained high temperaturecan cause the material of the tire to de-generate and reduce tire life, and exces-sive temperature can lead to sudden tirefailure. The grade C corresponds to a lev-el of performance which all passenger cartires must meet under the Federal MotorVehicle Safety Standard No.109. Grades Band A represent higher levels of perfor-mance on the laboratory test wheel thanthe minimum required by law.

Warning: The temperature grades for thistire are established for a tire that is prop-erly inflated and not overloaded. Exces-sive speed, underinflation, or excessiveloading, either separately or in combina-tion, can cause heat buildup and possibletire failure.


230 2002 MY CELICA_U (OM20792U)



Publication No. OM20792UPart No. 01999-20792Printed in Japan 01−0108−00 C

( U)

Quick index

� If a service reminder indicator or warning buzzer comes on 76. . . . . . . . .

� If your vehicle will not start 152. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� If your engine stalls while driving 155. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� If your vehicle overheats 155. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� If you have a flat tire 156. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� If your vehicle needs to be towed 166. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� Tips for driving during break−in period 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� How to start the engine 140. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� General maintenance 179. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

� Complete index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gas station information

Fuel type:

1ZZ−FE engine: UNLEADED gasoline, Octane Rating 87 (Research Octane Number 91) or higher2ZZ−GE engine: Premium UNLEADED gasoline, Octane Rating 91(Research Octane Number 96) or higher

See page 126 for detailed information.

Fuel tank capacity: 55 L (14.5 gal., 12.1 lmp. gal.)

Engine oil: API grade SJ “Energy−Conserving”, SL “Energy−Conserving” or ILSACmultigrade engine oil is recommended.

See page 192 for detailed information.

Tire information: See pages 196 through 200.

Tire pressure: See page 223.

U−5



You should know as much about the quality and

importance of proper maintenance of your new

vehicle as the people who built it.

The Toyota authorized Repair Manual

tells you how to maintain your vehicle and

enables you to correctly perform your own

maintenance.

The best way to keep your new vehicle in toprunning order is to maintain it properly fromthe moment you drive it off the showroomfloor.

The Toyota authorized Repair Manual ispacked with literally everything you need toknow to perform your own maintenance invirtually every area of your new vehicle.



Where to obtain the

Repair Manual

The repair manual for CELICA, written in Eng-

lish, may be purchased as applicable from any

Toyota dealer.

Pub. Name: 2002 CELICA Repair ManualPub. No.: RM902U1 (Maintenance, Preparation,

Service specifications and Diagnos-

tics)

RM902U2 (Engine, Chassis and Body)

Maintenance procedures for the engine,

chassis, body, electrical system, and more,

are clearly explained and illustrated.

Periodic maintenance and tune−up

Periodic maintenance and tune−up helps to pre-vent small problems from growing into larger ones lat-er on. The repair manual outlines exactly what main-tenance is required and clearly explains how to do thework yourself step−by−step.

Areas covered include such things as spark plug re-placement, valve clearance adjustment and engine oiland filter replacement.

Documents

Foreword - Just Give Me The Damn Manual...02MY CELICA U (L/O 0108) iv 2002 MY CELICA_U (OM20792U) Spark ignition system of your Toyota The spark ignition system in your Toyota meets