Slide 1

Floor Standing BouncepadTraining Videos & Instructions

1

Whats in the box:

2Contents:Whats in the boxStep 1: Attach the Floorstanding Pole to the Floorstanding baseStep 2: Slide the Base Cover over the Floorstanding PoleStep 3: Clip the Base Cover collar togetherStep 4: Attach the secure case to the Floorstanding PoleStep 5: Feed the supplied cable through the Floorstanding PoleStep 6: Complete the alignment of the BouncepadStep 7: Unlock and remove the face of the secure caseStep 8: Connect cable to Table and place into Secure caseStep 9: Lock the face of the Secure Case back into place

Placard Board Attachment: Assembly InstructionsStep 1: Slide the Bottom Bracket over the PoleStep 2: Attach the Top BracketStep 3: Affix your Placard board to the Brackets

How to Pack the Floorstanding Bouncepad

Step 1:Attach the floorstanding pole to the floorstanding base.Ensure the cable channel is positioned towards the rear of the unit.

If you wish to secure the unit to the floor, use the four M6 sized countersunk holes in the floorstanding base, using a screw that is suitable for your floor material.

1

2

Step 2:Slide the Base Cover over the Floorstanding PoleAlign the cable notch in the Base Cover with the cable channel in the Floorstanding base, then use the adhesive tabs to afix the Floorstanding cover to the Floorstanding base.

Removable cover lid: remove this lid when plugging iPad charger into floor socket.

12

Step 3:Clip the Base Cover collar togetherClip the base cover collar together.

Slide down to fit securely into the Base cover.

12

Step 4:Attach the secure case to the Floorstanding PoleBe sure to fully engage all screws in their threads before tightening. Always use a hand screwdriver for this step.

If a Placard Board is being used please refer to the instructions on Slide 15

1

Step 5:Feed the supplied cable through the Floorstanding poleFeed the supplied cable through the Floorstanding pole.

Connect to your power supply.

21

Step 6:Complete the alignment of the BouncepadFirstly loosen the two screws (shown left) slightly and align the case to be horizontal.

When the case is aligned, tighten screws up again using a hand screwdriver.

21Step 7:Unlock and remove the face of the secure case

This video clip will demonstrate how to remove the iPad from the Secure Case, simply click on the image below:

11Step 8:Connect cable to Tablet and place into Secure Case

Step 9:Lock the face of the Secure Case back into place

This video clip will demonstrate how to lock your tablet into the Bouncepad Secure Case, simply click on the image below:

14

Placard Board Attachment: Assembly InstructionsWhats included in the box:Placard BoardBottom BracketTop BracketM4 x 200mm Screw (x4)M4 Plastic Washer (x4)

12345If you have already attached the secure case to the pole, remove it using a hand screwdriver.Then slide the bottom bracket from the top, to the bottom of the floorstanding pole, letting it rest on the Floorstanding cover.Step 1:Slide the Bottom Bracket over the Pole

2Step 2:Attach the Top Bracket

1Whilst the Secure Case is still off, affix the Top Bracket using the M4 x 25mm Buttonhead Security Screws, clamping it between the Secure Case and the pole.Step 3:Affix your Placard Board to the Brackets

Align with the holes on the Placard Board with the top and Bottom Brackets. Affix the Placard Board to the Top and Bottom Brackets using the M4 x 20mm Plastic ScrewsPlace M4 Plastic Washers at the back of the Placard Board and attach securely to the board.

2 3 How to pack the Floorstanding Bouncepad

Foam Insert OverlayBase CoverFloorstanding BaseFloorstanding PoleSecure Case & Long USB CableKeys & Screws