Financial Bid GG,BS,CB etc. BGB - · PDF fileof bentonite muck from the factory premises etc complete in all ... 2911 (Part-IV) including installation of ... with demonstrable properties

Signature of the tenderer 1 under seal of the firm

RITES LTD

OPEN TENDER NOTICE NO: 142/OT/RCF-BGB/Ancillary Bldg./2012

Dated 15.02.2012

TENDER DOCUMENT FOR

Construction of Ancillary Buildings like Gas Godown cum Tools Store,

Bogie Store, Canteen Building, Toilet Block cum Parking, Compressor

Room and other works in connection with Bogie & AC Container

Manufacturing Factory at Budge Budge of RCF at West Bengal

Part – 2 (FINANCIAL BID)

(PERCENTAGE RATE TENDER)

FEBRUARY – 2012

Issued to (Name of Tenderer):________________________________________

Address of tenderer:_________________________________________________

Signature of officer issuing the documents___________________

Designation _______________________________

Date of Issue___________________

RITES LTD

(A Govt. of India Enterprise)

Regional Project Office, KOLKATA

56, C. R. Avenue, 2nd

floor, Kolkata – 700 012

e.mail : [email protected]

Phone No: (033) 2236 7118/7146/7162/7143(Fax)


PART – 2

FINANCIAL BID

SCHEDULE (BILL) OF QUANTITIES


RITES LTD.

OPEN TENDER NOTICE NO: 142/OT/RCF-BGB/Ancillary Bldg./2012 Dated

15.02.2012

Name of work: Construction of Ancillary Buildings like Gas Godown cum Tools

Store, Bogie Store, Canteen Building, Toilet Block cum Parking,

Compressor Room and other works in connection with Bogie & AC

Container Manufacturing Factory at Budge Budge of RCF at West

Bengal

Completion Time: 6 (Six) months from the 15th day after the date of issue of Letter of

Acceptance or from the first day of handing over of the site, whichever is later, in accordance

with the phasing, if any, indicated in the Tender Documents

RATE INDEX

(Percentage Rate Tender)

TENDERER SHOULD QUOTE THEIR RATES HERE UNDER ONLY

1. CIVIL ENGINEERING WORKS:

Sl. No Schedule No. Estimated Cost (In Rs.)

Quoted rates by bidders (Percentage above or below)

1 Schedule A

(RCC Bored

Piling work)

32,09,532.57 Rate quoted are _________________ % (in

Figures)________________________

(in words) above /below * on schedule in A

2 Schedule B

(General works)


Figures)________________________

(in words) above /below * on schedule in B

3 Schedule B-I

(Brick work)


Figures)________________________

(in words) above /below * on schedule in B-I

4 Schedule B-II

(Concrete &

Shuttering work)


Figures)________________________

(in words) above /below * on schedule in B-II

5 Schedule B-III

(Supply of

Reinforcement


Figures)________________________

(in words) above /below * on schedule in B-III


Steel)

6 Schedule B-IV

(Supply of

Cement)


Figures)________________________

(in words) above /below * on schedule in B-IV

7 Schedule B-V

(Plumbing &

Sanitary works)


Figures)________________________

(in words) above /below * on schedule in B-V

8 Schedule C

(Internal

Electrification)


Figures)________________________

(in words) above /below * on schedule in C

9 Schedule D

(Any other

unforeseen items)


Figures)________________________

(in words) above /below * on schedule in D

Total 3,15,23,359.63

Say 3,15,23,360.00

* Strike out which is not applicable

i) SIGNATURE OF AUTHORISED

SIGNATORY OF TENDERER

ii) NAME OF SIGNATORY

iii) NAME AND SEAL OF TENDERER

iv) DATE

v) PLACE Note:

i) TENDERERS ARE REQUESTED TO QUOTE THEIR RATE IN THE PREVIOUS PAGE ONLY

AND NOT IN SCHEDULES. BASIC RATES HAS BEEN SHOWN IN SCHEDULES FOR

GUIDENCE.

ii) THE SUCCESSFUL BIDDER WHO WILL BE AWARDED THE WORK WILL HAVE TO SUBMIT TAX INVOICE BEFORE RECEIVING PAYMENT FROM RITES.


SCHEDULE OF QUANTITY

Sl. No.

Description of Item Unit Qty. Rate (Rs.)

Amount (Rs.)

Schedule - A (RCC Bored Piling work)

Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of all length M-25 grade to carry a safe working load not less than specified incl. cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and pile to be embedded in the pile cap etc. all incl. removal of excavated earth with all lifts and leads beyond land boundary limit. Length of pile for payment shall be measured from founding level to cut off level of pile. Payment for steel reinforcement & cement will be made separately.

1

600mm dia. Piles Note:- i) The above rate includes mobilization & de-mobilization

of equipment, breaking of foam concrete of cast piles, removal

of bentonite muck from the factory premises etc complete in all

respect.

M 1857 1658.91 3080595.87

2 Conducting load testing of a single pile upto following capacity in accordance with IS:2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. with all labour, material, tool & plants, equipment, machinery, etc. complete as per drawing and specification, as directed by the Engineer Conducting load testing of a single pile upto following capacity in accordance with IS:2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. with all labour, material, tool & plants, equipment, machinery, etc. complete as per drawing and specification, as directed by the Engineer Single pile above 50 tonne and upto 100 tonne capacity - routine test

Each 2 38252.00 76504.00

3 Lateral load testing of single pile in accordance with I.S. Code of practice IS: 2911 ( Part IV )for determining safe allowable lateral load on pile for determining safe allowable lateral load on pile Vertical load capacity above 50 tonne and upto 100 tonne

Each 2 26216.35 52432.70

Cost of Schedule - A 3209532.57

Schedule - B (General works)


Earth work in excavation as per approved drawings and dumping at embankment site or spoil heap, within railway land, including 50m lead and 1.5m lift, the lead to be measured from the centre of gravity of excavation to centre of gravity of spoil heap; the lift to be measured from natural ground level and paid for in layers of 1.5m each including incidental work, as per specifications all kinds of soils The cost of Earthwork in excavation is including of Shoring & Dewatering

cum 924 88.16 81459.84

1

Extra for every additional lift of 1.5m or part thereof after the initial 1.5m for earth work in all soils cum 924 8.62 7964.88

2 Extra over item 1 above for excavation in foundations for buildings and bridges to cover dressing to neat dimension and plumbing sides etc. Note : Dressing under this item is payable for the total quantity of excavation in foundation and not partly.

cum 924 9.20 8500.80

3 Extra for lead of earthwork above initial lead of 50m in all kind of soils:

For every 50m or part thereof - lead over 50m and upto 150m cum 100 11.50 1150.00

For every 50m or part thereof - lead over 150m and upto 500m cum 790 9.10 7189.00

4 Filling, watering and ramming earth in 15cm layers in floors and foundations with surplus earth from foundations including 50m lead and 1.5m lift. cum 493 20.40 10057.20

5 Supplying and filling sand in plinth and under floors including

watering, ramming, consolidating and dressing complete. cum 1247 359.67 448508.49

6 Flat Brick flooring with bricks of class designation 7.5 including cement slurry etc. complete in cement mortar r 1:4 (1 cement : 4 coarse sand) (with FPS Bricks)

Sqm 755 192.07 145012.85

7 Water proofing of roofs and exposed concrete surfaces using polymeric waterproofing compound by cleaning and drying the surface; applying two coats (DFT of 200-300 micron) of translucent brown coloured phenolic resin based single component high performance polymeric waterproofing compound @ 0.6 litre per sqm, with demonstrable properties of resistance to water and acid; spraying a layer of dry coarse sand on the second coat when still wet; removing excess sand on the following day; permitting to coatings to cure and dry naturally for 3-7 days; providing a 12mm thick cement-sand (1:4) cover plaster; curing the plaster; the treatment shall be impermeable under a waterhead of 20m (removal of existing damaged waterproofing system, PCC, Lime Terracing etc., if any to be paid extra under separate item).

Sqm 600 275.34 165204.00


8 Making drain mouth on roof waterproof by cleaning the surface of the structure at the location of drain mouth; lowering the drain mouth to the level of the concrete roof; chipping thorough cleaning; mixing throughly an octadecanoic acid based cementitious waterproofing compound in the weight ratio of 50 cement (OPC or slag) and 3 waterproofing compound; placing the drain mouth in its final position, followed by filling of the annular space around the drain pipe with a paste of waterproofing compound-cement; sealing the edges of the drain mouth with acrylic-styrene based copolymer waterproofing compound

Each 30 465.88 13976.40

9 15 mm cement plaster finished with a floating coat of neat

cement of mix - 1:4 (1 cement : 4 fine sand) Sqm 2928 71.56 209527.68

10 20 mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1 cement : 4 fine sand) Sqm 2510 83.37 209258.70

11 Cement plaster to ceiling of mix -

12mm thick -

12mm thick 1:4 (1 cement : 4 fine sand)

Sqm 1172 62.44 73179.68

12 Providing and applying plaster of Paris putty of 2mm average thickness over plastered surface to prepare the surface even and smooth complete

Sqm 4375 76.54 334862.50

13 Applying one coat of cement primer of approved brand and manufacture on wall surface Sqm 11133 25.16 280106.28

14 Finishing walls with Acrylic smooth interior paint of required shade on new work (two or more coats applied @1.67 litre/10sqm over and including base coat of water proofing cement paint applied @2.20 kg/10aqm

Sqm 5562 86.47 480946.14

15 Extra for appiying water proofing cement paint as primer applied @ 2.2kg/ 10sqm instead of primer for exterior finishing

Sqm 11133 2.86 31840.38

16 Finishing walls with Acrylic smooth Exterior paint of required shade on new work (two or more coats applied @1.67 litre/10sqm over and including base coat of water proofing cement paint applied @2.20 kg/10aqm

Sqm 2510 91.31 229188.10

17 Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coats applied @ 0.90 litre/10sqm over an under coat of primer applied @ 0.80 litre/10sqm of approved brand or manufacture. Deduct cost of applying priming coat red oxide zink chormate. (72.63-10.52=62.11)

Sqm 400 62.11 24844.00


18 Providing and fixing ceramic tiles conforming to IS:15622 of manufacturers approved by railway in all colours, shades, design and abrasion resistance class as approved by the Engineer-in-Charge in floors and landings over 20mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) including pointing in white cement mixed with pigment of matching shade complete of Group B-I-a of IS:15622 (Vitrified tiles) of size above 400mm x 400mm upto 600mm x 600mm (For entire floor area except bathroom, kitchen & pot wash room)

Sqm 240 1102.32 264556.80

19 Of Group B-II Clause 5.1 (for abrasion resistance) of IS:15622 (Ceramic Floor Tiles) of size 400mm x 400mm and above (For bathroom, kitchen & pot wash room's floor) Sqm 95 598.88 56893.60

20 Providing and fixing 10mm thick heavy duty acid and/or alkali resisrant factory made tiles conforming to Group V-RD series of approved make and colour using acid and /or alkali resisting mortar bedding and joint filled with acid and /or alkali resisting mortar bedding and joints filled with acid and/or alkali resisting cement as per IS:4457 complete including cost of acid/alkali resistant cement In flooring on a bed of 10mm thick mortar 1:4 (1 appropriate cement : 4 coarse sand) (For Floor of Bogie store & Gas godown building)

Sqm 260 1076.43 279871.80

21 Providing and fixing 1st quality ceramic tiles conforming to Group B-III (Ceramic wall tiles) of IS: 15622 of manufacturers approved by railway in all colours, shades, and design as approved by the Engineer-in-charge in skirting, risers of steps and dado over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mixed with pigment of matching shade complete 200 x 300 mm

Sqm 355 673.17 238975.35

22 Supplying and applying surface hardener for concrete floors ready to use, specially graded, non metallic and mineral aggregate dry shake surface hardener free from oil and grease to be sprinkled at 9 kg/sqm of surface area, complete with finishing

Sqm 150 272.81 40921.50

23 Kota stone slab flooring of size up to 60cm×60cm over 20mm (average) thick base of 1:4 cement morter (1cement : 4 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete t : 4 coarse sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete 20 mm thick

Sqm 175 1169.69 204695.75

Extra for nosing in steps and treads of kota stone slab. sqm 30 144.64 4339.20


24 Providing and fixing 40mm thick Cuddappah stone polished, machine cut for kitchen platforms, vanity counters facias, dados and skirting and similar locations of required size, laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touchups including rubbing, curing etc. complete at all levels Area of slab over 1 sqm but upto 2 sqm or larger

Sqm 15 2161.54 32423.10

25 Providing and fixing 18mm thick mirror polished, machine cut for kitchen platforms, facias and similar locations of required size of approved shade, colour & texture laid over 20mm thick base cement mortar 1:4 (1 cement:4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing etc. complete at all levels. Granite Black or any approved colour - Area of Slab over 1.0 sqm but upto 2.0 sqm or larger

Sqm 15 3646.55 54698.25

26 Providing wood work in frames of doors, windows, clerestory windows and other frames and trusses, wrought, framed and fixed in position : Sal wood

Cudm 992 52.03 51613.76

27 Providing and fixing flush door shutters to IS: 2202 Part-I non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3-ply veneering with vertical grains of cross bands and face veneers on both faces of shutters 35mm thick including ISI marked stainless steel butt hinges with necessary screws

Sqm 15 1352.28 20284.20

28 Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (overall area of door shutters to be measured) Sqm 15 599.72 8995.80

29 French spirit polishing Two or more coats on new work including a coat of wood filler Sqm 38 121.10 4601.80


30 Providing and fixing anodised aluminium work for doors, windows ventilators and partitions with extruded built-up standard tubular and other sections of approved make conforming to IS:733 and IS:1285, anodised transparent or dyed to required shade according to IS:1868 (Minimum anodic coating of grade AC - 15), fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free straight, mitered and jointed mechanically wherever required including cleat angle. Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and directions of Engineer-in-charge. (Glazing & panelling to be paid for separately) For fixed/openable/sliding portion

Kg 400 494.56 197824.00

For openable/sliding portions and fixing hinges/pivots, PVC/neoprene gasket required and making provision for fixing of fittings. (Fittings shall be paid for separately) Kg 100 514.02 51402.00

31 Supplying, providing and fixing white colour sliding uPVC Door complete, consisting of uPVC frame of size 95mmx60mm and uPVC shutter of size 66mmx42mm with 1.2mm thick GI section reinforcement wherever required, produced by ISO 9001:2000 and ISO 14001:2004 certified company. Door shutter will consist either of 5mm thick float glass or galvanised wire gauge or solid PVC panel alongwith complete fittings, e.g. pulley/rollers, transmission gear and handle for operating door.

Sqm 20 7031.94 140638.80

32 Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade I, Type II conforming to IS:12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass/stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade I, Type II conforming to IS:12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P brass/stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge Prelaminated particle board with decorative lamination on both sides

Sqm 12 975.61 11707.32

33 Providing and fixing glazing in aluminium ventilator etc. with PVC/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) With float/frosted glass panes of 4mm thikness (weight not less than 10.0 kg/sqm)

Sqm 200 907.36 181472.00


34 Providing and fixing ISI standard steel glazed doors, windows and ventilators of standard rolled steel sections (shutters & frame)with 15mm x 3mm lugs, 10cm long, embeded in cenent concrete blocks 15 x 10 x10cm of 1:3:6 (120mm nominal size) or with wooden plugs and screws or with fixing clips or with bolts and nuts as required, including providing and eixing glass panes with glazing clips and specialmetal sash putty of arreoved make, necessary fittings such as brass handles, brass peg stays, brass spring catch, priming coat of approved steel primer; but excluding the cost of metal beading i) Windows fixed

Sqm 75 2920.12 219009.00

ii) Ventilators-centre hung Sqm 90 3190.24 287121.60

35 Providing and fixing circular cast iron box for ceilling fan clamps 140mm internal dia.73mm height, 5mm thick rim, bottom and top lid of 1.5mm thick M.S. top lid shall be screwed into the cast iron box by means of 3.3mm dia round headed screws, one lock at the corners, clamps shall be made of 12mm dia.M.S. bar bent to shape as per standerd drawing.

Each 35 110.39 3863.65

36 Steel work welded in built-up sections / farmed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required in gratings, frames, guard bar, ladders, raillings, brakets, gates, louvers and similar works.

Kg 1500 100.50 150750.00

37 Providing and fixing hand rail by welding etc. to steel ladders railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. E.R.W. tubes 40mm nominal dia

Kg 248 137.98 34219.04

38 Providing and fixing MS round or square bars / flats or grills in frames in window and clerestory windows sqm 37 63.83 2361.71

39 providing & fixing in position Collapsible steel shutters with vertical channels 20mmx10mmx2mm and braced with flat iron diagonals 20mmx5mm size with top and bottom rail of T-iron 40mmx40mmx6mm with 40mm dia. Steel pulleys complete with bolts, nuts, locking arrangement, stoppers,handles and hold fasts including applying a priming coat of approved steel primer.

sqm 25 3457.49 86437.25

40 Supplying and fixing rolling shutters of approved make as per IS:6248, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire spring grade no. 2 and M.S. top cover of required thickness for rolling shutters : 80x1.25mm M.S. laths with 1.25mm thick top cover.

sqm 16 2470.18 39522.88


Providing and fixing ball bearing for rolling shutters. Each 4 447.40 1789.60

41 Providing and fixing copper oxidised brass 100mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality) Each 17 906.79 15415.43

42 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete (best make of approved quality) Single rubber stopper

Each 16 37.93 606.88

43 Providing & fixing aluminium tower bolts ISI marked anodised

(anodic coating not less than grade AC 10 as per IS:1868)

transparent or dyed to required colour or shade with necessary

screws etc. complete:

300mm x 10mm

Each 6 64.76 388.56

250 mm x 10 mm Each 6 99.10 594.60

200 mm x 10 mm Each 6 81.91 491.46

150mm x 10mm Each 6 74.50 447.00

44 Providing and fixing IS:3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete Hardwyn make (Eddy) or equivalent

Each 9 1481.86 13336.74

45 Structural steel work welded in built up sections, trusses and framed work, girders, stagings, racks, etc. including cutting, bending, straightening, hoisting, fixing in position including applying a priming coat of approved steel primer complete - upto 6m height above GL tc. including cutting, bending, straightening, hoisting, fixing in position including applying a priming coat of approved steel primer complete - upto 6m height above GL In RSJ, tees, angles and channels

Kg 5000 100.34 501700.00

46 Erecting roof trusses, staging etc. including rivetting for work upto 10m height above GL Quintal 50 226.26 11313.00

47 Supplying, fitting/fixing corrugated fibre glass reinforced perspex

sheet 3mm thick on existing wooden or iron frames/purlins with

Contractor's stiching bolts, hook bolts, crank bolts, coach

screws, nuts,limpets, G.I and bitumen washers etc. complete Sqm 115 458.86 52768.90

Total of Schedule - B 6030829.25


Schedule - B-I (Brick work)

1 Brick work with non-modular (FPS) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6nt mortar 1:6 (1 cement : 6 fine sand) Cum 418 2163.97 904539.46

2 Extra over item no. 1 for brick work in superstructure beyond plinth level upto floor two level. cum 268 151.99 40733.32

3 Extra for brickwork in superstructure beyond second floor level for every 3m or part thereof cum 15 287.47 4312.05

4 Honey-comb brick work 20/23 cm thick with bricks of class

designation 7.5 in cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 32 355.85 11387.20

5 Half brick masonry with bricks of class designation 7.5 in foundations and plinth in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Sqm 485 265.31 128675.35

6 Extra for half brick masonry in superstructure above plinth level upto floor two level Sqm 310 42.15 13066.50

Total of Schedule - B-I 1102713.88

Schedule - B-II (Concrete & Shuttering work)

1 Providing and laying Plain Cement Concrete up to plinth in retaining walls, walls (any thickness) including attached plasters, columns, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets etc, excluding the cost of cement and of shuttering, centering. 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size)

cum 155 2325.34 360427.70

2 Providing and laying in position M-25 Grade concrete for

reinforced concrete structural elements, but excluding cost of

centering, shuttering, reinforcement and Admixtures in

recommended proportion (as per IS:9103) to accelerate, ratard

setting of concrete, improve workability without impairing

strength and durability as per direction of Engineer in charge.

All works upto plinth level, Pile cap, Tie beam

cum 201 2732.49 549230.49

All works in buildings above plinth level upto floor two level cum 357 3004.22 1072506.54

Extra for RCC work in superstructure above floor two level for every floor or part thereof

cum 13 316.54 4115.02


3 Supplying & mixing high range poly carboxylate ether base water reducing admixture Plast Super-C700 conforming to IS:9103-1999 (to be added @1% by weight of cement) for CC & RCC work for controlling water cement ratio and for gaining early strength

Kg 1420 77.03 109382.60

4 Centering and shuttering including strutting, propping etc. and

removal of form work for Fundations, footings, bases of

columns, Sqm 460 146.28 67288.80

5 Centering and shuttering including strutting, propping etc. and removal of form for ng strutting, propping etc. and removal of form for Pile caps,Tie beam, plinth beam, column etc.

Sqm 1391 145.90 202946.90

Suspended floors, roofs, landings, balconies, walkway slabs and access platform Sqm 1535 234.36 359742.60

Lintels, beams, plinth beams, bed blocks, girders, cantilevers etc. Sqm 1080 208.55 225234.00

Columns, pillars etc. Sqm 671 297.00 199287.00

Stairs (excluding landings) except spiral staircases Sqm 169 289.10 48857.90

6 Extra for additional height in centering, shuttering wherever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m for every additional height of 1 metre or part there of in suspended floors, roofs, landing, beams and balconies (plan area to be measured)

Sqm 5882 92.10 541732.20

7 Supplying & applying shuttering oil for mould releasing,having (flash point 54 degree C and specific gravity 0.88±0.02) for concrete formwork to be applied either brush or with spray machine to the entire satisfaction Engineer incharge.

Sqm 5612 6.43 36085.16

Total of Schedule- B-II 3776836.91

Schedule - B-III (Supply of Reinforcement)

1 Supplying reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete l complete Thermo-Mechanically Treated bars

Kg 133000 69.36 9224880.00

Total of Schedule- B-III 9224880.00


Schedule - B-IV (Supply of Cement)

1 Ordinary Portland Cement Grade-43 / Portland Slag Cement

MT 728 7302.50 5316220.00

Total of Schedule- B-IV 5316220.00

Schedule-B-V (Plumbing & Sanitary works)

1 Providing and fixing on wall face unplasticised Rigid PVC single socketed rain water pipes conforming to IS:13592 Type-A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion 110mm dia.

M 315 232.69 73297.35

2 Providing and fixing on wall face unplasticised PVC moulded bend and shoe for unplasticised-Rigid PVC rain water pipes conforming to IS:13592 Type-A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion shoe (Plain), 110mm dia. shoe

Each 38 283.77 10783.26

110mm Dia Bend Each 30 127.87 3,836.10

110mm coupler Each 38 104.64 3,976.32

Single tee with Door 110mmx110mmx110 Each 38 393.77 14,963.26

3 Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete 110mm

Each 195 127.22 24807.90

4 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast iron 'P' or 'S' trap, 10 litres low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : white vitreous China Orissa pattern W.C. pan of size 580mmx440mm with integral type foot rests.

Each 5 3128.93 15644.65

5 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litres low level white vitreous china flushing cistern and C.P flush bend with fittings & C.I./M.S. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito-proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors, wherever required : W.C. pan with ISI marked white solid plastic seat and lid.

Each 7 4263.34 29843.38


6 Providing and fixing white, vitreous china flat back half stall urinal of 580mm x 380mm x 350mm with white P.V.C. automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other coupling in C.P. brass including painting of fittings and cutting and making good the walls and floors, wherever required : Range of two half stall urinals with 5 litres P.V.C. automatic flushing cistern.

Each 4 7359.21 29436.84

7 Supplying and fixing marble stone 20mm to 25mm thick in masonry or concrete as a purdha to urinal range etc. Stone to be machine cut and well polished on all faces and the edges to be moulded by semi circular rounding & polishing. Marble shall be any one of the following: be machine cut and well polished on all faces and the edges to be moulded by semi circular rounding & polishing. Marble shall be any one of the following: Makrana Chalk Doongri

sqm 8 1802.13 14417.04

8 Providing and fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls, wherever required : White, vitreous china wash basin size 630mm x 450mm with a pair of 15mm C.P. brass pillar taps.

Each 13 1993.27 25912.51

9 Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white, P.V.C. automatic flushing cistern, with fittings, standard size G.I. flush pipe for back and front flush with standard spreader pipes with fitings, G.I. clamps and C.P. brass coupling complete including painting of fittings and cutting and making good the walls and floors etc., wherever required : single squatting plate of 600mm x 350mm size with 5 litres P.V.C. automatic flushing cistern.

Each 2 3960.91 7921.82

10 Providing and fixing white, vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Each 13 1110.13 14431.69

11 Providing and fixing PTMT Bottle Trap for Wash basin and sink : Bottle trap 31mm single piece moulded with height of 270mm, effective length of tail pipe 250mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 270gm.

Each 13 476.99 6200.87

12 Providing and fixing PVC connector 15mm size with non-corrosive PTMT couplings in both ends 15mm dia. 450mm long. Each 21 77.12 1619.52

13 Providing and fixing Stainless Steel AISI-304 (18/8) kitchen sink with drain board as per IS:13983 with C.I. brackets and stainless stel plug 40mm including painting of fittings and brackets, cuting and making good the walls, wherever required : 510mm x 1040mm bowl depth 250mm

Each 4 6262.30 25049.20


14 Providing and fixing 600mm x 450mm bevelled edge mirror, 5.5mm thick of float glass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Each 10 850.23 8502.30

15 Providing and fixing 600mmx120mmx5mm glass shelf with edges round or supported on anodised aluminium angle frame with c.p. brass brackets and guard rail complete fixed with 40mm long screws, rawl plugs etc. complete

Each 11 480.17 5281.87

16 Providing and fixing Towel rail (C.P.) brass 15mm dia x 600mm long having approx. weight 500gm Each 7 350.48 2453.36

17 Providing and fixing Soap dish (C.P. Brass) having approx. weight 220 gm Each 10 157.28 1572.80

18 Providing and fixing Liquid soap container (C.P. Brass) having approx weight 240 gm. Each 10 189.08 1890.80

19 Providing and fixing C.P. brass grating with openable lid : Grating 100mm nominal dia and 12mm high domed shape having weight not less than 25 gm Each 17 123.82 2104.94

20 Providing & filling the joints with spun yarn cement slurry and cement mortar 1:2 (1 cement : 2 fine sand ) in S.C.I./C.I. pipes100mm dia. Pipe

Each 10 43.14 431.40

21 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : flexible pipe 32mm dia. Each 19 78.20 1485.80

22 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete : Semi-rigid pipe 32mm dia.

Each 19 55.75 1059.25

23 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors : 100mm inlet and 100mm outiet sand cast iron S&S as per IS:1729

Each 16 851.02 13616.32

24 Providing and fixing Toilet paper holder (C.P. Brass) having approx. weight 250 gm Each 9 240.18 2161.62

25 Providing and fixing Coat hook 'J' type two way (C.P. Brass) Each 8 101.14 809.12

26 Supplying and fixing half round white glazed earthen ware drains 100mm dia. With cement sand mortar 1:3 mix and joints grouted with neat cement slurry of the matching colour : M 55 186.20 10241.00

27 Providing and fixing soil, waste and vent pipes 100mm dia. Centrifugally cast (spun) iron S & S pipe as per IS:3989 metre 105 701.93 73702.65


28 Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron/cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. for 100mm dia. pipe

Each 60 105.82 6349.20

29 Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete 100mm dia. Sand cast iron S&S as per IS-3989 Each 12 490.15 5881.80

30 Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diameter 100mm Each 45 75.25 3386.25

31 Providing and fixing plain bend of required degree 100mm dia. Sand cast iron S&S as per IS-3989 Each 12 400.52 4806.24

32 Painting two or more coats on, sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff etc. over a coat of primer (of approved quality) to give an even shade for new work 100mm diameter pipe

metre 60 25.87 1552.20

33 Providing & fixing single equal plain junction of required degree with access door, insertion rubber wash 3mm thick, bolts and nuts complete : 100mm x 100mm x 100mm sand cast iron S&S as per IS-3989

Each 12 641.67 7700.04

34 Supplying, fixing and fittings cowls to vent pipes : Wire cowls for pipes of size 50/75 mm dia. Each 12 103.18 1238.16

35 Providing and fixing 110mm dia PVC soil, waste and vent pipes including jointing and cost of spun yarn and sand etc. complete. M 60 266.19 15971.40

36 Providing and fixing brackets comprising of aluminium painted standard steel clip and cast iron base for 110mm pipes, including cost of screws etc. and drilling of holes and making good the walls including cost of sand etc. complete.

Each 57 82.54 4704.78

37 Providing, laying and jointing glazed stoneware pipes grade 'A' as per IS:651 including bends etc. with stiff mixture of cement mortar in the proportion of 1:1 (1cement : 1 fine sand) including testing of joints etc. complete : 100mm diameter

M 45 177.60 7992.00

38 Providing, laying and jointing glazed stoneware pipes grade 'A' as per IS:651 including bends etc. with stiff mikture of cement mortar in the proportion of 1:1 (1cement : 1 fine sand) including testing of joints etc. complete : 150mm diameter

M 10 177.60 1776.00


39 Providing and fixing square-mouth S.W. gully trap grade 'A' complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300mm size (inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70kg as per standard design : 150x100mm size 'P' type with F.P.S. bricks class designation 7.5

Each 4 1266.81 5067.24

40 Constructing brick masonry mahhole in cement mortar 1:4 (1 cement : 4 coarse sand) R.C.C. top slab with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90cm x 80cm and 45cm deep including C.I. cover with frame (light duty) 455mm x 610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg) with F.P.S. bricks class designation 7.5

Each 4 4673.34 18693.36

41 Making soak pit 2.5m diameter, 3m deep with 45x45cm dry brick honey comb shaft with bricks of class designation 7.5 and S.W. drain pipes 100mm diameter, 1.8m long complete as per standard design, including excavation complete : with F.P.S. bricks

Each 4 12619.61 50478.44

42 Supplying, fitting & fixing in position reinforced cement polymer concrete (RCPC) manhole cover and frame to match with IS:12592 with cement concrete 1:2:4 for embedding the manhole cover frame: 3 MT load bearing capacity manhole cover provided with 2 nos. lifter lock fitted with matching frame ( size of cover: 440mm dia x 50mm thick and size of frame:750mm dia x 150mm thick)

Each 10 1232.99 12329.90

43 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes including bends etc with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete upto 800mm dia : 150mm dia. R.C.C. pipe.

M 30 260.88 7826.40

44 Providing and fixing medium grade G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the wall etc. : Concealed pipe including painting with anti-corrosive bitumestic paint, cutting chase and making good the wall 15mm dia. nominal bore

M 140 195.86 27420.40

20mm dia. nominal bore M 65 242.17 15741.05

45 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall alls etc. Internal work - Exposed on wall 40mm dia. Nominal bore

M 80 355.79 28463.20


80 mm dia. Nominal bore M 44 631.16 27771.04

46 Making connection of medium grade G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete 100mm to 80mm nominal bore.

Each 6 1090.99 6545.94

47 Providing and fixing PP-R Male adopter conforming to PN-25 rating with marking on each fitting, fusion welded, having thermal stability for hot & cold water supply and testing of joints complete as per direction of engineer in charge 20mm adopter for PPR-GI connection.

Each 22 227.39 5002.58

48 Providing and fixing PP-R Brass Ball Valve fusion welded, having thermal stability for hot & cold water supply and testing of joints complete as per direction of engineer in charge 20mm Ball Valve. Each 18 761.73 13711.14

49 Providing and fixing gun metal non-return valve of 40mm nominal bore approved quality (screwed end) : vertical Each 3 1683.36 5050.08

50 Providing and fixing C.P. brass bib cock, 15mm nominal bore of approved quality conforming to IS:8931 Each 11 469.88 5168.68

51 Providing and fixing C.P brass stop cock, 15mm nominal bore, (concealed) of standard design and of approved quality conforming to IS:8931 Each 24 404.48 9707.52

52 Polyethylene Vinyl Chloride water storage tank (make SINTEX or equivalent) with cover and suitable locking arrangement litre 10000 8.63 86300.00

53 Hoisting, fitting and fixing in position plastic moulded water

storage tank including making connection of intake, delivery, outlet

and overflow pipes etc. with all lead & lift upto all stories. (cost of

tanks/fittings to be paid separately)

2500 litre capacity tank

Each 4 1506.76 6027.04

Total of Schedule- B-V

820117.02


Schedule - C (Internal Electrification work)

Unit rate Amt Sl No Description of item Unit Qty

( Rs) in Rs

01 Supply & wiring of concealed light / fan/call

bell/ 5 amps socket points

No 385 302.70 116539.50

02 Supply & concealed wiring by 4 sq. mm

single core copper cable for 5/15 amps

socket points & submain wire from DB to

individual switch board

Rmt 930 55.03 51177.90

03 Supply & concealed wiring for submain

from Main DB to Sub DB by 10 Sqmm

single core copper cable

Rmt 40 210.32 8412.80

04 Supply, fixing & commissioning of 6 pin,

5/15 amps sockets.

No 11 121.00 1331.00

05 Supply, fixing & commissioning of 1 X 28

W T- 5 Box type FL fittings

No. 124 609.00 75516.00


W T- 5 Box type FL fittings

No 74 1606.00 118844.00

07 Supply, fixing & commissioning of CFL

fitting with 11W lamp

No 31 225.00 6975.00

08 Supply, fixing & commissioning of Bulk

Head fitting with 11W CFL lamp

No 4 1586.00 6344.00

09 Supply, fixing of 1400 mm sweep, ceiling

fan

No 24 1606.00 38544.00

10 Supply, fixing of stepped type electronic fan

regulator

No 24 150.00 3600.00

11 Supply & fixing of Wall bracket fan

400 mm sweep No. 16 2355.00

37680.00

12 Supply & fixing of 300mm sweep exhaust

fan

No 38 1412.48 53674.24

13 Supply, fixing & commissioning of SPN DB

DD 4 way with one DPMCB, 10 amps & two

SPMCB, 6 amps

Set 28 2674.58 74888.24


14 Supply, fixing & commissioning of TPN DB

DD 4 way with one FPMCB, 40 amps & 8

SPMCB, 10 amps

Set 6 8062.93 48377.58

15 Supply, fixing & commissioning of cubical

LT panel containing three FPMCB 63amps,

busber 100 amps 01 set,

Set 2 9919.86 19839.72


W T- 5 flame proof type FL fittings

No. 18 17508.42 315151.56


W T- 5 flame proof type FL fittings

No 12 32719.33 392631.96

18 Supply, fixing & commissioning of 20A, 2

pin, scrapping earth, 2 module,metal plug &

socket with DPMCB 20 A

No 6 2135.34 12812.04

19 Supply & erection of GI pipe earthing complete

Set 40 1652.00 66080

20 Supply & Main wiring for 3 phase by 10 sq

mm single core & 4 sq mm single core

copper cable through 25 mm dia black

conduit

Rmt 40 269.80 10792

21 Supply, installation, testing & commissioning of water cooler

Set 1 38018.82 38018.82

22 Supply & errection of ISI marked dry

chemical powder type fir extinguisher of

capasity 2 KG

No 30 1500.00 45000

Total of Schedule- C 1542230.36

Schedule - D (Any other unforeseen items)

1 Any other unforseen item which is not covered under the above schedule of works will be executed from Unified Standard Schedule of Rates/Eastern Railway-2011 ( Basic Cost:- Rs. 5,00,000/-)

500000.00

Total of Schedule-D 500000.00

Total Cost of Schedule - A + B + B-I + B-II + B-III + B-IV + B-V + C + D 31523359.63

Say 31523360.00

Rupees Three Crore Fifteen Lakh Twenty Three Thousand Three Hundred Sixty Only