EZ Crate Assembly and Installation

Form No. 1-1148May 2016

EZ Crate Assembly and Installation 51350, 51450, 51500, 51575, 51600, 51675, 51700 & 51775

Super V Plow with V-70 12V Hydraulic Unit

© 2016 Printed in the U.S.A.

Meyer Products LLC18513 Euclid Ave. • Cleveland, Ohio 44112-1084

Phone 216-486-1313www.meyerproducts.com• email [email protected]

Meyer Products LLC reserves the right, under its continuing product improvement program, to change construction or design details, specifications and prices without notice or without incurring any obligation.

Table of Contents

General Information ..................................................................................................................................................................................................1

Illustrated Parts Lists ............................................................................................................................................................................................ 2-5

Build Assembly ........................................................................................................................................................................................................6

Vehicle Side Wiring Diagram ................................................................................................................................................................................. 7-8

Drop Speed Adjustment ............................................................................................................................................................................................8

Stop Bolt Adjustment ................................................................................................................................................................................................8

Mount Plow System To Vehicle ..................................................................................................................................................................................9

Dis-Mount Plow System From Vehicle .....................................................................................................................................................................10

Pre-Delivery Inspection ...........................................................................................................................................................................................11

Accessories ...........................................................................................................................................................................................................12

Web Based Support

(1)

GENERAL INFORMATION

Always disconnect battery prior to installation.

SAFETY PRECAUTIONS should be used when Quik Lift® is in a RAISED position.

LOWER plow to the ground when vehicle is PARKED.

OVERHAUL and SERVICE information is covered on separate instructions.

Lift arm should be removed from vehicle if / when snowplow is removed.

Note:1. Connect ground cable to negative side of battery for a solid connection to ground.2. Route all cables away from moving engine parts, Manifolds, and sharp sheet metal.3. For weather protection, coat all connections with Meyer Dielectric Grease Part No. 156324. The vehicle must be equipped with a “Heavy Duty Battery” (70 Amp, Hr. Min.), 550 C.C.A. and “Alternator” (60 Amp. Min.) to obtain maximum performance.5. Follow these instructions explicitly. Warranty does not apply to a Meyer product which has been negligently or improperly assembled or installed.

ADDITIONAL BATTERY CONNECTIONS

1. When attaching cables to battery with side post terminals, use M.P. Adaptor Part #21976.2. Coat battery connections with battery terminal coating.

Bolt Nut Size Gr. 2 Gr. 5 Gr. 8

1/4 - 20 4 - 55/16 - 18 9 - 113/8 - 16 17 - 20 26 - 297/16 - 14 42 - 46 60 - 661/2 -13 64 - 72 90 - 1005/8 - 11 127 - 141 179 - 198

TORQUE CHART FOOT POUNDS

Please check the contents of your crate. Page 2 shows the assembled parts in the left hand column and the accessory box in the right hand column. Page 3 is the diagram for the left hand column of page 2.

http://www.meyerproducts.com/

TechSupport/ServiceManualsandIn-

stallationInstructions.aspx


techsupport/EZtroubleshooter.aspx


TechSupport/OwnersManuals.aspx

http://www.youtube.com/playlist?list=PLDE0602B305314D92&feature=edit_ok

Service Manuals EZ-Troubleshooter Owners Manual Mount/Dismount Videos

Please visit our website to find our most updated technical information.

Tool list for Plow assembly:Pliers1/2" socket1/2" box wrench9/16" box wrench

9/16" socket3/4" box wrench15/16" box wrench15/16" deep well socket

Parts Diagram

Parts List

Parts indented are included in the carton, bag or assembly under which they are indented.

V-70 PKGItem Part No. Qty. Description 15192 1 V-70 Hydraulic Carton 12V w/o Controller 1 05024 1 • Power Cable - 36” 2 05815 1 • Lift Ram 1.75 x 8” 3 07628 2 • Ram Assembly 1-1/2 x 12 DA 4 05755 1 •• Ram (1-1/2” x 12”) DA 5 22866 2 •• SAE Mx3/8 90 Degree Elbow 6 22868 2 •• Straight Fitting SAE 3/8 x 3/8 7 22884 1 •• Hose 1/4 x 33” 8 22941 1 •• Hose 3/8 x 33” 08202 1 • Plug Bracket Kit 9 19607 1 •• Plug Bracket 10 19609 1 •• Plate 11 20027 2 •• Bolt H 5/16-18 x 1 Gr. 2 12 20326 4 •• Lockwasher 5/16 13 20525 4 •• Finish Nut 5/16-18 14 22658 2 •• Bolt H 5/16-18 x 3 Gr. 2 08799 1 • Hardware Bag 15 15067 1 •• Breather 16 15634 1 •• Hydraulic Cover 17 20029 4 •• Bolt H 5/16-18 x 1-1/2” Gr. 2 18 20050 2 •• Bolt H 3/8-16 x 1-1/4” Gr. 2 19 20152 2 •• Bolt H 5/8 - 11 x 5” Gr. 5 20 20153 2 •• Bolt H 5/8 - 11 x 5-1/2” Gr. 5 21 20304 4 •• Locknut 5/16-18 22 20309 4 •• Locknut 5/8-11 23 20327 2 •• Lockwasher 3/8” 24 21398 2 •• Self Tap Screw 1/4-14 x 3/4” 25 22153 1 •• Lockbolt 5/16 x 5/8 26 22866 1 •• SAE Mx3/8 90 Degree Elbow 27 22868 1 •• Straight Fitting SAE 3/8 x 3/8 28 13333 1 • V-70 Mounting Bracket 29 15094 1 • V-70 Hydraulic Unit 12V 30 15370 1 • Motor Solenoid 31 15633 1 • Cover Strap 32 22691S 1 • Truck Side Harness 33 22696 1 • Super V Plow Side Harness 34 22883 1 • Hose 1/4 x 22” 35 07550 1 • Nite Sabre II Kit 36 12557 1 • Pivot Pin Super V 37 13755 1 • A-frame Super V Plus 38 19365 1 • Lift Frame

V-70 PKGItem Part No. Qty. Description

16628 1 • Hardware Carton 08815 1 •• Hardware Bag 39 20028 4 ••• Bolt H 5/16-18 x 1-1/4” Gr. 2 40 20146 1 ••• Bolt H 5/8 - 11 x 3-1/4” Gr. 5 41 20152 1 ••• Bolt H 5/8 - 11 x 5” Gr. 5 42 20153 1 ••• Bolt H 5/8 - 11 x 5-1/2” Gr. 5 43 20309 3 ••• Locknut 5/8-11 44 20326 4 ••• Lockwasher 5/16” 45 20331 2 ••• Lockwasher 5/8” 46 20406 2 ••• Cotter Pin 3/16 x 1-1/2” 47 20420 2 ••• Cotter Pin 1/4 x 2” 48 20525 4 ••• Finish Nut 5/16-18 49 22436 2 ••• Pin 1 x 3” 50 814000005 2 ••• Spring 51 8500003307001 2 ••• Bolt H 5/8-11 x 3 Full Thread 52 8501003013 4 ••• 5/8-11 Jam Nut 08964 1 •• Hardware Bag 53 13724 1 ••• Deflector Brace 54 14205 2 ••• Backing Plate 55 20028 7 ••• Bolt H 5/16-18 x 1-1/4” 56 20095 1 ••• Bolt H 1/2-13 x 1-1/2” 57 20304 7 ••• Locknut 5/16-18 58 20309 2 ••• Locknut 5/8-11 59 20329 1 ••• Lockwasher 1/2” 60 20352 7 ••• Flatwasher 5/16” 61 21962 2 ••• Bolt C 5/8-11 x 2-3/4” 09917 1 •• Plow Marker Kit 62 08214 2 ••• Plow Marker 63 20027 4 ••• Bolt H 5/16-18 x 1 Gr.5 64 20304 4 ••• Locknut 5/16-18 65 20352 8 ••• Flatwasher 5/16” 66 11751 1 •• Light Bracket LH 67 11752 1 •• Light Bracket RH 68 11844 1 •• Receiver Tube Cap 69 11859 2 •• Blue Handle Pin 70 12536 1 •• Top Deflector Super V 71 14204 1 •• Bottom Belt 72 19370 1 •• Clevis EZ Mount Plus 73 19592 1 •• Lift Arm 74 22245 1 •• Crankstand

51350, 51450, 51500, 51575, 51600, 51675, 51700 & 51775 Super V Plow Package

(2)


Specific Components

(3)

Super V Plow Package

29

16

2

34

4

7

8 5

15

31

17 18

20

21

22

23

26

28

78

5

4

5

5

19

19

2022

27

72

66

67

6968

74

73

38

50

40

41

42

43

46

39

51

52

45

4448

43

43

4749

52

SV & SV2 Steel Parts List

Parts indented are included in the assembly under which they are indented.

(4)


Item 51350 51600 51450 51700 51500 Qty Description SV 8.5 SV2 8.5 SV 9.5 SV2 9.5 SV2 10.5 Moldboard Assembly 09217 09446 09226 09447 09237 1 R.H. & L.H. Wing 75 09208 09442 09212 09444 09280 1 • R.H. Wing 76 09209 09443 09213 09445 09279 1 • L.H. Wing 77 14195 14170 14196 14180 14151 2 •• Trip Edge Weld 5/8” Holes 78 22438 22438 22438 22438 22438 8 •• 1 X 2-1/2” Pin 79 22945 22945 21945 22945 22945 8 •• 1/4 x 1-1/2” Roll Pin 80 12528 84285 12528 84285 12528 2 •• T -Bar Weldment 81 07215 07215 07215 07215 07215 4 •• Trip Spring 82 20145 20145 20145 20145 20145 2 •• Bolt H 5/8-11 x 3” Gr. 5 83 20318 20318 20318 20318 20318 2 •• Locknut 5/8-11 84 20357 20357 20357 20357 20357 4 •• Flatwasher 5/8 85 09124 09124 09124 09124 09124 4 •• Eyebolt w/Locknuts and Cap 86 21262 21262 21262 21262 21262 8 •• Flatwasher 1” 87 09484 09484 09485 09485 09486 2 •• Cutting Edge 88 20309 20309 20309 20309 20309 14 •• Locknut 5/8-11 89 8500002267 8500002267 8500002267 8500002267 8500002267 14 •• Bolt C 5/8-11 x 2”

75

76

87

88

89

71

54

58

6180

81

36

70

6057

55

78

79

82

83

84

85

64

63

62

53

55

56

57

57

59

60

37

60

20

22

777158

6154

84

85

8180

87

77

76

75

78,79 & 86

82

83

88 & 89

Item 51675 51775 51575 Qty Description SV2 8.5 SS SV2 9.5 SS SV2 10.5 SS Moldboard Assembly 09494 09495 09496 1 R.H. & L.H. Wing 09466 09470 09476 1 • SS R.H. Wing 09467 09471 09477 1 • SS L.H. Wing 90 14055 14057 14129 1 •• RH Moldboard Weld 91 14056 14058 14130 1 •• LH Moldboard Weld 92 14059 14063 14131 1 •• RH Stainless Steel Sheet 93 14060 14064 14132 1 •• LH Stainless Steel Sheet 94 14098 14118 14150 2 •• Bottom Mount Plate 95 14170 14180 14151 2 •• Trip Edge Weld 96 20307 20307 20307 10 •• Locknut 1/2-13 97 20309 20309 20309 12 •• Locknut 5/8-11 98 21262 21262 21262 8 •• Flatwasher 1” SAE 99 21943 21943 21943 10 •• Bolt C 1/2-13 x 1-3/4” 100 22438 22438 22438 8 •• 1 X 2-1/2” Pin 101 22945 22945 22945 8 •• Roll Pin 5/16 x 1.5” 102 84285 84285 12528 2 •• T -Bar Weldment 103 07215 07215 07215 4 •• Trip Spring 104 20145 20145 20145 2 •• Bolt H 5/8-11 x 3” Gr. 5 105 20318 20318 20318 2 •• Locknut 5/8-11 106 20357 20357 20357 4 •• Flatwasher 5/8 107 09124 09124 09124 4 •• Eyebolt w/Locknuts and Cap 108 09484 09485 09486 2 • Cutting Edge 109 20309 20309 20309 14 •• Locknut 5/8-11 110 8500002267 8500002267 8500002267 14 •• Bolt C 5/8-11 x 2”

Parts indented are included in the assembly under which they are indented.

(5)


SV & SV2 Stainless Steel Parts List

60

90

91

92

93

9495

96

97 & 10998

99

100101

102

103104

105

106

107

108

110

715458

61

36

56

59

6264

63

70

53

6057

37

55

6057

57

55

20

22

(6)

Building Super V Plow

1. Position wing assemblies 75 & 76 or 90 & 91 face down on cardboard as not to damage the painted surfaces. Grease the bushings on both left and right wings. Position the wings so pivot bushings align. Note: Cutting Edges will be inline at this time.

2. Remove 1/2”-13 x 1” set screw located in top of A-Frame (37) tower. Grease A-Frame (37) bushings and Pivot Pin (36). With a helper, lift the A-Frame (37) and insert its bushings in alignment with the wing bushings.

3. Insert Pivot Pin (19) through bushings. Install and tighten 1/2” x 1.50” bolt (56) and 1/2” lockwasher (59) to top of A-Frame holding Pivot Pin (36) in place. Note: Wipe off any excess grease at this time.

4. Using the A-Frame as leverage tilt the moldboard assembly raising the Cutting Edges off the ground. Support Cutting Edges (87 or 108) 5 to 6 inches off the ground.

5. Install the Bottom Belt (71) to left and right wing at Tripedge (77 or 95) using 1/2” x 2.75” carriage bolt (61) and locknut (58). Note: Be sure that Belt (71) folds are upward and notches are toward the A-Frame (37). Assemble Backing Plate (54) so bent end is facing the cutting edge forcing the belt against the Tripedge (77 or 95).

6. Using the A-Frame as leverage tilt the moldboard assembly raising the Cutting Edges off the supports. Remove supports and set moldboard assembly to the upright position.

7. Assemble Snow Deflector Brace (53) to Pivot Pin (36). Place brace under the pivot pin plate. Attach using two 5/16” x 1-1/4” bolts (55), 5/16 washers (60) and 5/16 locknuts (57).

8. Position moldboard assembly in the “Vee” position.

9. Assemble Top Snow Deflector (70) positioning the deflector under deflector brace (53). Attach deflector ends under left and right wing gussets using 5/16” x 1-1/4” bolts (55), 5/16 locknuts (57) and 5/16 washers (60). Tighten locknuts such that washers slightly compress the rubber surface.

Note: Snow Deflector Belt should fold/loop downward between brace and each wing gusset when wings are not in the “Vee” position.

10. Assemble Lift Frame (38) tp A-frame (37) using 1 x 3” Pin (49) and 1/4 x 2” Cotter Pin (47).

11. Assemble Blue Handle Pin (69) to lift frame (38) by inserting the Blue Handle Pin (69) through the outer lift frame plates, through the center of the spring (50). At this time align the small blue leg on the handle through the notch on the outermost plate. Compress the spring (50) slightly with your fingers and insert the 3/16” x 1-1/2” Cotter Pin (46) through the small hole towards the center of the pin. With cotter pin (46) fully inserted, pull the blue handle until the spring is fully compressed and rotate the handle one full turn to bend the cotter pin in place. Realign the small blue leg with the notch on the outermost plate to lock in place. Repeat assembly process until both pins are assembled. Note: Lubricate the stainless steel pins and Lift Frame bearing surfaces with chassis grease or anti-seize lubricant periodically for easier disengagement of pins.

12. Assemble adjustable stacking stop bolts to lift frame (38) using 5/8-11 x 3” bolts (51), lockwasher (52) and jamnuts (52) per figure1. Note: Adjustment must be made after moldboard assembly is installed. Adjustment bolts (51) should make contact with the a-frame before any part of the A-Frame or moldboard come in contact with the lift arm and, or hydraulic unit while raising the snowplow or stacking snow. Moldboard should be checked in all positions.

13. Attach L.H. and R.H. Light Brackets (66 & 67) to the side plates of Lift Frame (38) in the upper two holes using 5/16”-18 x 1-1/4” bolts (39), 5/16” lockwashers (44), and 5/16”-18 hex nuts (48). Note: Light brackets may be adjusted down two levels in height for better appearance on lower profile vehicles. Tighten all fasteners to their proper torque.

14. Attach lift arm (73) to lift frame (38) using 5/8-11 x 5-1/2” bolt (42) and 5/8-11 locknut (43).

15. Install the V-70 Mounting Bracket (28) to the Lift Frame and Light Bracket (Passenger Side) using 5/16-18 x 1-1/2” Bolts (17) and 5/16-18 Locknuts (21). Install the V-70 Lift Assembly (29) to V-70 Mounting Bracket Assembly using Bolt H 3/8-16 x 1-1/4” (18) and 3/8 Lockwasher (23). Remove shipping plug on V-70 Lift Assembly and install Breather (15).

16. Attach the Lift Cylinder (2) to the Lift Frame using Bolt H 5/8-11 x 3-1/4” ( 40) and 5/8-11 Locknut (43). Attach the Lift Cylinder (2) to the Lift Arm using Bolt H 5/8-11

x 4-3/4” (41) and 5/8-11 Locknut (43). Attach elbow (26) to V-70 Lift Assembly (29) along with Hose (34) and attach hose (34) to Lift Cylinder (3) using Straight Fitting (27).

17. Attach fixed end of Wing Cylinders (4) to the A-Frame with a 5/8-11 x 5” bolt (19) and 5/8-11 locknut (22) on each side. Attach live end of Wing Cylinder rod (4) to the Wings using a 5/8-11 x 5” bolt (20) and 5/8-11 locknut (22) on each side.

18. Attach Wing Cylinders hoses to the V-70 Lift Assembly (29) by removing the caps from the hoses (7 & 8) and plugs from the V-70 Lift Assembly (1). Install Straight Fittings (6) to bottom of PA Block on V-70 Hydraulic Unit and connect hoses. See below. Use zip ties to route hoses away from moving plow parts to prevent chaffing.

19. Connect Super V Plow Side Harness (33) to V-70 Hydraulic Unit (29) as shown below.

S1

S2

S3

S5

S6

S7

(-)(+)

COIL COLOR CODES1 - RED WIRES2 - BLACK WIRES3 - GREEN WIRES5 - YELLOW WIRES6 - BLUE w/WHITE STRIPES7 - PURPLE WIRE

GROUND WIRE EACH COIL BLACK W/WHITE STRIPE

Driver Side Live End (1/4) Hose

Driver Side Fixed End (3/8) Hose

Pass Side Live End (1/4) Hose

Pass Side Fixed End (3/8) Hose

Lift Cylinder Hose Port

23. Meyer M-1 Hydraulic Fluid Part No. 15134 may need to be added to reservoir and bleed the Angle Cylinders, proceed as follows:

a. Remove Fill Plug from reservoir to add fluid during charging. b. Operate the Angle cylinders (2) until they are filled with Meyer M-1 Hydraulic Fluid and are not spongy.

c. Top off the unit to the fill line on the reservoir with Meyer M-1 Hydraulic Fluid.

NOTE: Proper fluid level is to the fill line on the reservoir for the V-70. It must be checked with the lift cylinder and both wing cylinders fully retracted.

(S) terminal white wire(I) terminal black wire w/white stripe

15059 Diode packed in Controller box

20. Run Universal Truck Side Harness (32) through a hole in grille and into the engine compartment. Sandwich vehicle grill between Plug Bracket (9) and Plate (10) using Bolt H 5/16-18 x 3” (14), 5/16 Lockwasher (12) and 5/16-18 Finish nut (13). Secure Universal Truck Side Harness (32) to Plug Bracket (9) using Bolt H 5/16-18 x 1” (11), 5/16 Lockwasher (12) and 5/16-18 Finish nut (13). Secure Universal Truck Side Harness (32) from any hot /

moving parts with tie wraps as needed.

21. Drill a 1-1/4” Diameter Hole thru firewall and extend the harness into the cab of the vehicle. Fused lead from Universal Truck Side Harness (32) must be attached to terminal in fuse panel that is activated only when the ignition key is “on.”

22. Install Motor Solenoid (30) to metal surface in engine compartment using Self Tapping Screws (24). (Solenoid must be grounded to operate). Attach Red Power Cable (32) to a large terminal on Motor Solenoid (30). Attach Black Ground Cable (32) to negative (-) terminal of battery. Attach Red Power Cable (1) to positive (+) terminal of battery and remaining large terminal on Motor Solenoid (30). Attach small white wire from harness (32) to small terminal (S) on Motor Solenoid (30). Attach small Black/white stripe wire from harness (32) to small terminal (I)(ground) on Motor Solenoid (30) At tach Blue wire to a reverse signal on the vehicle. The blue wire is sensing when the vehicle is in reverse in order to operate HFP (Hands Free Plowing).

E-72 Fill level lineE-72 Fill Plug

(7)

Vehicle Side Wiring Diagram

32

1

Optional Controller

30

24

9

10

11

1412

13

33 (See Figure 2)

Keyed Ignition (Blue)

Light Module "C" Harness

Light Module "B" Harness (Orange)

RedRed

Black

White

Blue Wire

Light Module "C" Harness

Reverse Signal

Black/WhiteStripe

12

13

For snow plow light installation see separate instructions.

Orange wire on Harness (32) will attach to both orange wires of the “B” harness supplied in the Light Module Kit. Reference Form 1-757

Route Cables “C” (Yellow) from module to Harness (32). Connect both “C” Harness female ends to the male corresponding ends of the Harness (32).

Connect both male ends from the snow plow light to the female ends on the Plow Side Harness (33).

Check snow plow light blinkers to make sure the wires have not been reversed.

Note: All electrical connections should have both ends coated with a dielectric grease, Meyer Part No. 15632, prior to final installation. This will ensure a good connection and help in preventing corrosion.

24. Refer to Operation and Maintenance Manual for complete controller operation.

25. After all electrical connections have been made the drop speed of the plow may be evaluated / adjusted. To adjust, loosen the hex nut and adjust in to slow the drop speed and out to make it faster. After ideal drop speed it achieved, retighten the hex nut. See below.

After cycling of the plow, recheck oil level.

V-70 Lower Adjustment:Loosen jam nut and turn knob clockwise to slow the drop of the plow and counter clockwise to speed the drop of the plow. Tighten jam nut.

(8)

27. Assemble adjustable stacking stop bolts to lift frame (38) using 5/8-11 x 3” bolts (51), lockwasher (45) and jamnuts (52). See below. Note: Adjustment must be made after moldboard assembly is installed. Adjustment bolts (51) should make contact with the a-frame before any part of the A-Frame or moldboard come in contact with the lift arm and, or hydraulic unit while raising the snowplow or stacking snow. Moldboard should be checked in all positions.

28. Attach Plow Markers (62) to moldboard using 5/16-18 x 1” Bolt (63), 5/16” Flatwasher (65) and 5/16-18 Locknut (64).

26. Attach the Lift Chain to the Lift Arm (73) through the two hooks on the lift arm. Adjust the lift chain at the lift arm so that there are 2-3 links of slack. This ensures that the plow blade will lift fully and be able to follow the ground contour while plowing.

75

76

87

88

89

71

54

58

6180

81

36

70

6057

55

78

79

82

83

84

85

64

63

62

53

55

56

57

57

59

60

37

60

20

22

777158

6154

84

85

8180

87

77

76

75

78,79 & 86

82

83

88 & 89

Meyer Products assumes no responsibility for installations not made in accordance with these instructions.

A. Pull vehicle into plow assembly and push plow assembly forward an inch or two.

F. Attach crankstand to lift frame.

E. Remove crankstand from a-frame.

D. Adjust crankstand until it is no longer in contact with the ground.

C. Push back on lift frame until both pins spring thru mount on vehicle.

B. Twist handles on both sides to engage spring loaded pins.

G. Remove weather cover on male end and connect one piece electrical plug. The spring loaded cover will lock one piece plug.

For Mounting and Dis-mounting instructional video’s please visit www.youtube.com/meyerproducts

(9)

Mount Plow To Vehicle

A. Press down button until float light turns blue.

B. Push lift arm down until there is slack in the chain.

C. Remove crankstand from lift frame.

D. Attach crankstand to a-frame

E. Adjust crankstand until crankstand comes into contact with the ground and then turn 1 to 2 revolutions.

F. While slightly pushing the lift frame towards vehicle pull handles on either side to disengage pins then twist until the leg locks the pin in the open position.

G. Disconnect one piece electrical plug and install weather cover on male end.

H. Back vehicle away from plow assembly.

Meyer Products assumes no responsibility for installations not made in accordance with these instructions.

(10)

For Mounting and Dis-mounting instructional video’s please visit www.youtube.com/meyerproducts

Dis-Mount Plow From Vehicle

Vehicle Make: Vehicle Model: Vehicle Year: Vehicle VIN#: Vehicle FGAWR: Installing Company:

Mounting Type: Plow Type: EZ Plus 8.5 9.5 10.5

Hydraulic Serial Number: Moldboard Serial Number:

Comments:

Inspected By: W.O.# Date:

Customer Signature:

PRE-DELIVERY INSPECTION

All bolts torqued to specification Suspension interference Clevis height in inches Diode Installed Trip springs adjusted Lift Chain Adjusted Check for hydraulic fluid leaks Hydraulic fluid Level Dielectric grease applied to ALL electrical connection All wires/modules secured Plow Stops Adjusted (plow cannot bump hyd. unit) Controller Operation Controller Turns Off when vehicle shut off

Plow Operation Up Plow Operation Left & Right Plow Operation Vee, Scoop Left & Right Wing In & Out Plow Operation Down Plow Drop Speed Adjusted Plow Light Blinker Left & Right Operation Plow Light Low & High Beam Operation Plow Lights Adjusted Plow Mount/Dismount reviewed with Customer Plow Operation reviewed with Customer HFP (Hands Free Plowing) reviewed with Customer Warranty/Registration/Owners Manual reviewed with Customer

(11)

11-1/4"

Clevis height

Serial Number Decal Locations

V-70 unit serial number is under the cover attached to the

hydraulic unit.

Moldboard serial number is attached to the back of the moldboard.

Please see your owner’s manual for Pre-Season, Post-Season and general maintenance.

CUTTING EDGE KITS DEFLECTOR KITS POLY STEEL L t Pro Moldboard and A CURB SNOW CENTER CENTER PART NO. DESCRIPTION Steel Rubber Urethane Molded Rubber Poly GUARDS SHOES EDGE EDGE

51350 SV 8.5 STEEL 09487* 08424 08413 N/A 12579 N/A 08344 09214 08409 08432 51450 SV 9.5 STEEL 09488* 08425 08414 N/A 12643 N/A 08344 09214 08409 08432 51500 SV2 10.5 STEEL 09489* 08426 08415 N/A 13045 N/A 08344 09214 08409 08432 51575 SV2 10.5 SS 09489* 08426 08415 N/A 13045 N/A 08344 09214 08409 08432 51600 SV2 8.5 STEEL 09487* 08424 08413 N/A 12579 N/A 08344 09214 08409 08432 51675 SV2 8.5 SS 09487* 08424 08413 N/A 12579 N/A 08344 09214 08409 08432 51700 SV2 9.5 STEEL 09488* 08425 08414 N/A 12643 N/A 08344 09214 08409 08432 51775 SV2 9.5 SS 09488* 08425 08414 N/A 12643 N/A 08344 09214 08409 08432

(12)

Super V Moldboard Accessories

Controllers and Controller Accessories

*Included with moldboard

Mounting Accessories

22790XJoy Stick

23010Pistol Grip (Wireless)

22695DCPistol Grip DLX

22799Joy Stick

Cradle Mount

22798Pistol Grip

Cradle Mount

2281545-Degree

Cradle Adapter

22801 (10”)22844 (20”)Floor Mount

16529Meyer

Winch Cradle

08300 Brush Guard

Optional Light Guards16536 (‘99-07 Ford)16537 (‘99 + Chevy)16539 (‘99 + Dodge)

Please visit http://www.meyerproducts.com/plows/lotpro.aspx for a complete listing of accessories

© 2016 Printed in the U.S.A.

Meyer Products LLC18513 Euclid Ave. • Cleveland, Ohio 44112-1084

Phone 216-486-1313www.meyerproducts.com• email [email protected]

Documents

EZ Crate Assembly and Installation