EMC TEST REPORT - logitech.com EN30148… · Report No.: RM990811E03 6 Report Format Version 3.0.3 CERTIFICATION - Continued The test record, data evaluation & Equipment Under Test

Report No.: RM990811E03 1 Report Format Version 3.0.3

EMC TEST REPORT

REPORT NO. : RM990811E03

MODEL NO. : A-E0001

RECEIVED : Aug. 11, 2010

TESTED : Aug. 11 to 17, 2010

ISSUED : Aug. 24, 2010

APPLICANT : LOGITECH FAR EAST LTD.

ADDRESS : #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C.

ISSUED BY : Bureau Veritas Consumer Products Services

(H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory

LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan

TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan

TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan

This test report consists of 65 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by any government agencies. The test results in the report only apply to the tested sample.


Table of Contents 1 CERTIFICATION .................................................................................................................. 5 2 SUMMARY OF TEST RESULTS........................................................................................... 7 2.1 MEASUREMENT UNCERTAINTY ........................................................................................ 8 3 GENERAL INFORMATION................................................................................................... 9 3.1 GENERAL DESCRIPTION OF EUT...................................................................................... 9 3.2 GENERAL DESCRIPTION OF TEST MODE .......................................................................10 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................................11 3.4 DESCRIPTION OF SUPPORT UNITS.................................................................................12 3.5 CONFIGURATION OF SYSTEM UNDER TEST ..................................................................13 4 EMISSION TEST.................................................................................................................14 4.1 CONDUCTED EMISSION MEASUREMENT .......................................................................14 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT .....................................................14 4.1.2 TEST INSTRUMENTS.........................................................................................................14 4.1.3 TEST PROCEDURE............................................................................................................15 4.1.4 DEVIATION FROM TEST STANDARD ................................................................................15 4.1.5 TEST SETUP ......................................................................................................................15 4.1.6 EUT OPERATING CONDITIONS.........................................................................................16 4.1.7 TEST RESULTS(MODE 1) ..................................................................................................17 4.1.8 TEST RESULTS(MODE 2) ..................................................................................................19 4.1.9 TEST RESULTS(MODE 3) ..................................................................................................21 4.2 HARMONICS CURRENT MEASUREMENT ........................................................................23 4.2.1 LIMITS OF HARMONICS CURRENT MEASUREMENT ......................................................23 4.2.2 TEST INSTRUMENTS.........................................................................................................23 4.2.3 TEST PROCEDURE............................................................................................................24 4.2.4 DEVIATION FROM TEST STANDARD ................................................................................24 4.2.5 TEST SETUP ......................................................................................................................25 4.2.6 EUT OPERATING CONDITIONS.........................................................................................25 4.2.7 TEST RESULTS(MODE 1) ..................................................................................................26 4.2.8 TEST RESULTS(MODE 2) ..................................................................................................26 4.2.9 TEST RESULTS(MODE 3) ..................................................................................................27 4.3 VOLTAGE FLUCTUATION AND FLICKERS MEASUREMENT.............................................28 4.3.1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKERS MEASUREMENT...........................28 4.3.2 TEST INSTRUMENTS.........................................................................................................28 4.3.3 TEST PROCEDURE............................................................................................................28 4.3.4 DEVIATION FROM TEST STANDARD ................................................................................29 4.3.5 TEST SETUP ......................................................................................................................29 4.3.6 EUT OPERATING CONDITIONS.........................................................................................29 4.3.7 TEST RESULTS(MODE 1) ..................................................................................................30 4.3.8 TEST RESULTS(MODE 2) ..................................................................................................31


4.3.9 TEST RESULTS(MODE 3) ..................................................................................................32 5 IMMUNITY TEST.................................................................................................................33 5.1 GENERAL DESCRIPTION ..................................................................................................33 5.2 GENERAL PERFORMANCE CRITERIA DESCRIPTION .....................................................34 5.3 EUT OPERATING CONDITION...........................................................................................36 5.4 ELECTROSTATIC DISCHARGE IMMUNITY TEST (ESD) ...................................................37 5.4.1 TEST SPECIFICATION .......................................................................................................37 5.4.2 TEST INSTRUMENTS.........................................................................................................37 5.4.3 TEST PROCEDURE............................................................................................................38 5.4.4 DEVIATION FROM TEST STANDARD ................................................................................38 5.4.5 TEST SETUP ......................................................................................................................39 5.4.6 TEST RESULTS(MODE 1~3) ..............................................................................................40 5.5 RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST (RS) ...43 5.5.1 TEST SPECIFICATION .......................................................................................................43 5.5.2 TEST INSTRUMENTS.........................................................................................................43 5.5.3 TEST PROCEDURE............................................................................................................44 5.5.4 DEVIATION FROM TEST STANDARD ................................................................................44 5.5.5 TEST SETUP ......................................................................................................................45 5.5.6 TEST RESULTS(MODE 1~3) ..............................................................................................46 5.6 ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (EFT)......................................47 5.6.1 TEST SPECIFICATION .......................................................................................................47 5.6.2 TEST INSTRUMENTS.........................................................................................................47 5.6.3 TEST PROCEDURE............................................................................................................47 5.6.4 DEVIATION FROM TEST STANDARD ................................................................................48 5.6.5 TEST SETUP ......................................................................................................................48 5.6.6 TEST RESULTS(MODE 1~3) ..............................................................................................49 5.7 SURGE IMMUNITY TEST ...................................................................................................50 5.7.1 TEST SPECIFICATION .......................................................................................................50 5.7.2 TEST INSTRUMENTS.........................................................................................................50 5.7.3 TEST PROCEDURE............................................................................................................51 5.7.4 DEVIATION FROM TEST STANDARD ................................................................................51 5.7.5 TEST SETUP ......................................................................................................................52 5.7.6 TEST RESULTS(MODE 1~3) ..............................................................................................53 5.8 IMMUNITY TO CONDUCTED DISTURBANCES INDUCED BY RF FIELDS (CS) ................54 5.8.1 TEST SPECIFICATION .......................................................................................................54 5.8.2 TEST INSTRUMENTS.........................................................................................................54 5.8.3 TEST PROCEDURE............................................................................................................55 5.8.4 DEVIATION FROM TEST STANDARD ................................................................................55 5.8.5 TEST SETUP ......................................................................................................................56 5.8.6 TEST RESULTS(MODE 1~3) ..............................................................................................57 5.9 VOLTAGE DIP/SHORT INTERRUPTIONS/VOLTAGE VARIATIONS (DIP) IMMUNITY TEST58


5.9.1 TEST SPECIFICATION .......................................................................................................58 5.9.2 TEST INSTRUMENTS.........................................................................................................58 5.9.3 TEST PROCEDURE............................................................................................................59 5.9.4 TEST SETUP ......................................................................................................................59 5.9.5 TEST RESULTS(MODE 1~3) ..............................................................................................60 6 PHOTOGRAPHS OF THE TEST CONFIGURATION ...........................................................61 7 APPENDIX - INFORMATION ON THE TESTING LABORATORIES .....................................65


1 CERTIFICATION

PRODUCT: Logitech Wireless Headset F540

BRAND NAME: Logitech

MODEL NO.: A-E0001

APPLICANT: LOGITECH FAR EAST LTD.

TESTED: Aug. 11 to 17, 2010

TEST SAMPLE: R&D SAMPLE STANDARDS: EN 301 489-1 V1.8.1 (2008-04)

EN 301 489-3 V1.4.1 (2002-08) EN 55022:2006+A1:2007, Class B EN 61000-3-2:2006, Class A EN 61000-3-3:2008 EN 61000-4-2:2009 EN 61000-4-3:2006+A1:2008 EN 61000-4-4:2004+A1: 2010 EN 61000-4-5:2006 EN 61000-4-6:2009 EN 61000-4-11:2004

The above equipment (Model: A-E0001) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. Approval signature – on next page


CERTIFICATION - Continued The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report.

PREPARED BY :

, DATE: Aug. 24, 2010 ( Midoli Peng, Specialist )

TECHNICAL ACCEPTANCE

:

, DATE: Aug. 24, 2010 ( Ray Yeh, Deputy Manager )

APPROVED BY :

, DATE: Aug. 24, 2010

( May Chen, Deputy Manager )

Note *: The power consumption of EUT is 2.976W, which are less than 75W and no limits apply. Therefore it is deemed to comply with EN 61000-3-2 without any testing.


2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications:

EMISSION Standard Test Type Result Remarks

Conducted Test PASS Meets Class B Limit Minimum passing margin is -1.90 dB at 10.063 MHz

Telecommunication Ports Conducted Test NA Not Applicable

EN 55022:2006 +A1:2007, Class B

Radiated Test NA Not Applicable

EN 61000-3-2:2006, Class A

Harmonic current emissions PASS

The power consumption of EUT is less than 75W and no limits apply

EN 61000-3-3:2008 Voltage fluctuations & flicker PASS Meets the requirements

IMMUNITY

Standard Test Type Result Remarks

EN 61000-4-2:2009 Electrostatic discharge immunity test PASS Meets the requirements of

Performance Criterion B

EN 61000-4-3:2006 +A1:2008

Radiated, radio-frequency, electromagnetic field immunity test

PASS Meets the requirements of Performance Criterion A

EN61000-4-4:2004 +A1: 2010

Electrical fast transient / burst immunity test. PASS Meets the requirements of


EN 61000-4-5:2006 Surge immunity test PASS Meets the requirements of Performance Criterion A

EN 61000-4-6:2009

Immunity to conducted disturbances, induced by radio-frequency fields

PASS Meets the requirements of Performance Criterion A

EN 61000-4-11:2004

Voltage dips, short interruptions and voltage variations immunity tests

PASS

Meets the requirements of Voltage Dips: i) 0% residual for 0.5 cycle –

Performance Criterion A ii) 0% residual for 1 cycle –

Performance Criterion A iii) 70% residual for 25 cycle –

Performance Criterion A Voltage Interruptions: i) 0% residual for 250 cycle –



2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2: This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2.

Measurement Value Conducted emissions 2.45 dB


3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT

PRODUCT Logitech Wireless Headset F540 MODEL NO. A-E0001 POWER SUPPLY DC 6V from power adapter POWER CORD DC output cable (unshielded, 0.85m without core)

DATA CABLE SUPPLIED

RCA to RCA Passthrough cable (Unshielded, 1.9m) Mini-USB headset charging cable(Shielded, 1.2m) Mini-USB PS3 voice cable(Shielded, 1.2m)

I/O PORT

Mini-USB port x2 RCA to RCA port x1(for XBOX) RCA to RCA port x1(for PS3) AUX IN port x1

ASSOCIATED DEVICES

Power adapter

NOTE:

1. The EUT must be supplied with a power adapter as following table: BRAND Logitech MANUFACTURY PI ELECTRONICS MODEL AD631MB INPUT POWER AC 100~240V, 50/60Hz, 0.13A

OUTPUT POWER DC 6V, 0.85A DC output cable (unshielded, 0.85m without core)

2. The above EUT information was declared by manufacturer and for more detailed features description, please refer to the manufacturer's specifications or user's manual.


3.2 GENERAL DESCRIPTION OF TEST MODE

The EUT was tested under following test modes:

Test Mode Description Mode 1 XBOX Mode : XBOX play music

Mode 2 AUX Mode : iPod play music

Mode 3 PS3 Mode : PS3 play music


3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards:

EN 301 489-1 V1.8.1 (2008-04), EN 301 489-3 V1.4.1 (2002-08) Emission tests: EN 55022:2006+A1:2007, Class B EN 61000-3-2:2006, Class A EN 61000-3-3:2008 Immunity tests: EN 61000-4-2:2009 EN 61000-4-3:2006+A1:2008 EN 61000-4-4:2004+A1: 2010 EN 61000-4-5:2006 EN 61000-4-6:2009 EN 61000-4-11:2004

Notes: The above EN basic standards are applied with latest version if customer has no

special requirement.


3.4 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. No. Product Brand Model No. Serial No. FCC ID

1 TV MONITOR Panasonic TH-L26K10W 9540684 NA 2 PLAYSTATION. 3 SONY CECHB07 27430232-9740084 FCC DoC 3 XBOX Microsoft XBOX 360 NA FCC DoC

4 Logitech Wireless Headset F540 (Headset)

Logitech A-R0002 NA NA

5 iPod APPLE A1199 YM712NGUVQ5 FCC DoC No. Signal cable description 1 1.9 m Audio cable x2. 2 1.2 m USB cable. 3 NA 4 1.2 m USB cable. 5 1.8 m Audio cable.

Note: 1. All power cords of the above support units are unshielded (1.8m).


3.5 CONFIGURATION OF SYSTEM UNDER TEST

1. TV MONITOR 2. PLAYSTATION. 3 (BOX)

2. PLAYSTATION. 3 (Rocker)

3. XBOX (BOX)

USB cable(1.2m) Audio cable(1.9m)

Audio cable(1.9m)

Audio cable(1.8m) USB cable(1.2m)

Wireless

3. XBOX (Rocker) 5. iPod

4. Logitech Wireless Headset F540 (Headset)

Adapter (on test table) EUT


4 EMISSION TEST

4.1 CONDUCTED EMISSION MEASUREMENT

4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT TEST STANDARD: EN 55022

Class A (dBuV) Class B (dBuV) FREQUENCY (MHz)

Quasi-peak Average Quasi-peak Average 0.15 - 0.5 79 66 66 - 56 56 - 46 0.50 - 5.0 73 60 56 46 5.0 - 30.0 73 60 60 50

NOTES: (1) The lower limit shall apply at the transition frequencies.

(2) The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz.

(3) All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above.

4.1.2 TEST INSTRUMENTS

DESCRIPTION & MANUFACTURER

MODEL NO. SERIAL NO. CALIBRATED DATE

CALIBRATED UNTIL

Test Receiver ESCS 30 100375 Mar. 09, 2010 Mar. 08, 2011 Line-Impedance Stabilization Network (for EUT)

NSLK 8127 8127-522 Sep. 23, 2009 Sep. 22, 2010

Line-Impedance Stabilization Network (for Peripheral)

ESH3-Z5 848773/004 Oct. 26, 2009 Oct. 25, 2010

RF Cable (JYEBAO) 5DFB COBCAB-001 Nov. 24, 2009 Nov. 23, 2010 50 ohms Terminator 50 3 Oct. 28, 2009 Oct. 27, 2010

Software BV ADT_Cond_V7.3.7

NA NA NA

Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are

traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. C. 3 The VCCI Con C Registration No. is C-3611.


4.1.3 TEST PROCEDURE a. The EUT was placed 0.4 meters from the conducting wall of the shielded room

with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument.

b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference.

c. The frequency range from 150 kHz to 30 MHz was searched. Emission levels under (Limit – 20dB) were not recorded.

4.1.4 DEVIATION FROM TEST STANDARD No deviation

4.1.5 TEST SETUP

N o t e : 1 .S u p p o r t u n i ts w e r e c o n n e c t e d t o s e c o n d L IS N .

2 .B o t h o f L IS N s ( A M N ) a r e 8 0 c m f ro m E U T a n d a t le a s t 8 0 c m

f r o m o t h e r u n i ts a n d o t h e r m e ta l p la n e s

V e r t ic a l R e f e re n c eG r o u n d P la n e

4 0 c m

8 0 c m

T e s t R e c e iv e r

H o r iz o n ta l R e f e re n c eG r o u n d P la n e

E U T

L IS N

For the actual test configuration, please refer to the related Item – Photographs of the Test Configuration.


4.1.6 EUT OPERATING CONDITIONS

For Mode 1 1. Turn on the power of EUT. 2. Set the EUT under typical use condition. 3. The support unit 3(XBOX) sends video messages to support unit 1(TV). 4. The support unit 3(XBOX) sends audio messages to EUT via one audio cable

and then EUT sends the audio messages to support unit 4(Logitech Wireless Headset F540(Headset)) via wireless.

For Mode 2 1. Turn on the power of EUT. 2. Set the EUT under typical use condition. 3. The support unit 5(iPod) sends audio messages to EUT via one audio cable


For Mode 3 1. Turn on the power of EUT. 2. Set the EUT under typical use condition. 3. The support unit 2(PS3) sends video messages to support unit 1(TV). 4. The support unit 2(PS3) sends audio messages to EUT via one audio cable



4.1.7 TEST RESULTS(MODE 1)

TEST MODE Mode 1 6dB BANDWIDTH 9 kHz

INPUT POWER 230Vac, 50Hz PHASE Line (L)

ENVIRONMENTAL CONDITIONS

25 deg. C, 50 % RH, 1014 hPa TESTED BY Eric Lee

Freq. Corr. Reading Value Emission Level Limit Margin

No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.185 0.05 50.96 - 51.01 - 64.25 54.25 -13.24 - 2 0.423 0.06 52.56 40.50 52.62 40.56 57.38 47.38 -4.76 -6.82 3 0.763 0.08 49.53 40.22 49.61 40.30 56.00 46.00 -6.39 -5.70 4 0.818 0.08 47.35 38.52 47.43 38.60 56.00 46.00 -8.57 -7.40 5 1.523 0.11 41.03 - 41.14 - 56.00 46.00 -14.86 - 6 1.980 0.13 46.57 36.36 46.70 36.49 56.00 46.00 -9.30 -9.51 7 2.141 0.13 50.01 40.20 50.14 40.33 56.00 46.00 -5.86 -5.67 8 2.582 0.15 46.07 37.85 46.22 38.00 56.00 46.00 -9.78 -8.00 9 4.758 0.21 40.68 - 40.89 - 56.00 46.00 -15.11 -

10 10.063 0.35 49.96 47.75 50.31 48.10 60.00 50.00 -9.69 -1.90 REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value.



INPUT POWER 230Vac, 50Hz PHASE Neutral (N)



Freq. Corr. Reading Value Emission

Level Limit Margin

No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.189 0.06 51.44 - 51.50 - 64.08 54.08 -12.58 - 2 0.213 0.06 52.35 - 52.41 - 63.11 53.11 -10.70 - 3 0.252 0.06 50.02 - 50.08 - 61.71 51.71 -11.62 - 4 0.345 0.07 45.14 - 45.21 - 59.07 49.07 -13.87 - 5 0.830 0.09 43.56 - 43.65 - 56.00 46.00 -12.35 - 6 0.912 0.10 41.73 - 41.83 - 56.00 46.00 -14.17 - 7 1.199 0.11 42.78 - 42.89 - 56.00 46.00 -13.11 - 8 1.316 0.11 39.71 - 39.82 - 56.00 46.00 -16.18 - 9 2.695 0.16 41.79 - 41.95 - 56.00 46.00 -14.05 -

10 3.840 0.20 40.62 - 40.82 - 56.00 46.00 -15.18 - REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value.








No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.185 0.05 51.00 - 51.05 - 64.25 54.25 -13.20 - 2 0.423 0.06 52.25 39.98 52.31 40.04 57.38 47.38 -5.07 -7.34 3 0.759 0.08 49.49 39.96 49.57 40.04 56.00 46.00 -6.43 -5.96 4 0.822 0.08 47.15 38.36 47.23 38.44 56.00 46.00 -8.77 -7.56 5 1.609 0.11 45.10 - 45.21 - 56.00 46.00 -10.79 - 6 1.844 0.12 44.36 - 44.48 - 56.00 46.00 -11.52 - 7 2.152 0.13 51.57 42.18 51.70 42.31 56.00 46.00 -4.30 -3.69 8 9.902 0.35 50.59 46.70 50.94 47.05 60.00 50.00 -9.06 -2.95

REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value.







Level Limit Margin

No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.162 0.06 53.76 - 53.82 - 65.38 55.38 -11.55 - 2 0.232 0.06 50.31 - 50.37 - 62.38 52.38 -12.01 - 3 0.420 0.07 42.83 - 42.90 - 57.46 47.46 -14.56 - 4 0.752 0.09 40.16 - 40.25 - 56.00 46.00 -15.75 - 5 0.818 0.09 43.02 - 43.11 - 56.00 46.00 -12.89 - 6 1.609 0.12 43.02 - 43.14 - 56.00 46.00 -12.86 - 7 1.699 0.13 41.41 - 41.54 - 56.00 46.00 -14.46 - 8 2.262 0.15 42.71 - 42.86 - 56.00 46.00 -13.14 - 9 10.063 0.36 33.05 - 33.41 - 60.00 50.00 -26.59 -









No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.189 0.05 49.73 - 49.78 - 64.08 54.08 -14.30 - 2 0.423 0.06 52.47 40.34 52.53 40.40 57.38 47.38 -4.85 -6.98 3 0.763 0.08 49.57 39.94 49.65 40.02 56.00 46.00 -6.35 -5.98 4 0.826 0.08 46.18 38.00 46.26 38.08 56.00 46.00 -9.74 -7.92 5 1.215 0.10 41.70 - 41.80 - 56.00 46.00 -14.20 - 6 1.680 0.12 46.94 34.96 47.06 35.08 56.00 46.00 -8.94 -10.92 7 2.148 0.13 51.54 43.07 51.67 43.20 56.00 46.00 -4.33 -2.80 8 2.227 0.14 50.25 39.82 50.39 39.96 56.00 46.00 -5.61 -6.04 9 10.063 0.35 50.00 47.67 50.35 48.02 60.00 50.00 -9.65 -1.98








Level Limit Margin

No Factor [dB (uV)] [dB (uV)] [dB (uV)] (dB) [MHz] (dB) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV. 1 0.209 0.06 51.34 - 51.40 - 63.26 53.26 -11.86 - 2 0.423 0.07 52.43 38.90 52.50 38.97 57.38 47.38 -4.88 -8.41 3 0.752 0.09 48.14 36.70 48.23 36.79 56.00 46.00 -7.77 -9.21 4 0.818 0.09 46.32 36.87 46.41 36.96 56.00 46.00 -9.59 -9.04 5 1.520 0.12 44.53 - 44.65 - 56.00 46.00 -11.35 - 6 1.602 0.12 48.53 35.69 48.65 35.81 56.00 46.00 -7.35 -10.19 7 1.906 0.14 45.36 - 45.50 - 56.00 46.00 -10.50 - 8 2.359 0.15 49.56 40.53 49.71 40.68 56.00 46.00 -6.29 -5.32 9 9.902 0.36 49.44 - 49.80 - 60.00 50.00 -10.20 -



4.2 HARMONICS CURRENT MEASUREMENT

4.2.1 LIMITS OF HARMONICS CURRENT MEASUREMENT TEST STANDARD: EN 61000-3-2

Limits for Class A equipment Limits for Class D equipment Harmonics

Order n

Max. permissible harmonics current

A

Harmonics Order

n

Max. permissible harmonics current per

watt mA/W

Max. permissible harmonics current

A Odd harmonics Odd Harmonics only

3 2.30 3 3.4 2.30 5 1.14 5 1.9 1.14 7 0.77 7 1.0 0.77 9 0.40 9 0.5 0.40 11 0.33 11 0.35 0.33 13 0.21 13 0.30 0.21 15<=n<=39 0.15x15/n 15<=n<=39 3.85/n 0.15x15/n

Even harmonics 2 1.08 4 0.43 6 0.30 8<=n<=40 0.23x8/n

NOTE: 1. Class A and Class D are classified according to section 5 of EN 61000-3-2

2. According to section 7 of EN 61000-3-2, the above limits for all equipment except for lighting equipment having an active input power > 75 W and no limits apply for equipment with an active input power up to and including 75 W.



MODEL NO. SERIAL NO.

CALIBRATED DATE

CALIBRATED UNTIL

EMC PARTNER EMC Emission Tester

HAR1000-1P 086 Aug. 10, 2010 Aug. 09, 2011

EMC Partner(Software) HARCS_V4.16 NA NA NA

NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA.

2. The test was performed in EMS room.


4.2.3 TEST PROCEDURE a. The EUT was placed on the top of a wooden table 0.8 meters above the ground

and operated to produce the maximum harmonic components under normal operating conditions for each successive harmonic component in turn.

The classification of EUT is according to section 5 of EN 61000-3-2. The EUT is classified as follows:

Class A: Balanced three-phase equipment, Household appliances excluding equipment as Class D, Tools excluding portable tools, Dimmers for incandescent lamps, audio equipment, equipment not specified in one of the three other classes.

Class B: Portable tools: Arc welding equipment which is not professional equipment.

Class C: Lighting equipment. Class D: Equipment having a specified power less than or equal to 600 W

of the following types: Personal computers and personal computer monitors and television receivers..

b. The correspondent test program of test instrument to measure the current harmonics emanated from EUT is chosen. The measure time shall be not less than the time necessary for the EUT to be exercised.



4.2.5 TEST SETUP

EUT

For the actual test configuration, please refer to the related item – Photographs of the Test Configuration.

4.2.6 EUT OPERATING CONDITIONS

Same as 4.1.6



FUNDAMENTAL VOLTAGE/AMPERE

231.3Vrms/ 0.048Arms

POWER FREQUENCY

50Hz

POWER CONSUMPTION

5.313W POWER FACTOR 0.478


30deg. C, 55%RH,

1012 hPa TESTED BY: Barry Lee

Note: Limits are not specified for equipment with a rated power of 75W or

less (other than lighting equipment).




POWER FREQUENCY

50Hz

POWER CONSUMPTION



30deg. C, 55%RH,








POWER FREQUENCY

50Hz

POWER CONSUMPTION



30deg. C, 55%RH,





4.3 VOLTAGE FLUCTUATION AND FLICKERS MEASUREMENT

4.3.1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKERS MEASUREMENT

TEST STANDARD: EN 61000-3-3

TEST ITEM LIMIT NOTE Pst 1.0 Pst means short-term flicker indicator. Plt 0.65 Plt means long-term flicker indicator.

Tdt (ms) 500 Tdt means maximum time that dt exceeds 3.3 %.

Dmax (%) 4% dmax means maximum relative voltage change.

Dc (%) 3.3% dc means relative steady-state voltage change




CALIBRATED DATE

CALIBRATED UNTIL

EMC PARTNER EMC Emission Tester

HAR1000-1P 086 Aug. 10, 2010 Aug. 09, 2011

EMC Partner(Software) HARCS_V4.16 NA NA NA


2. The test was performed in EMS room.

4.3.3 TEST PROCEDURE a. The EUT was placed on the top of a wooden table 0.8 meters above the ground

and operated to produce the most unfavorable sequence of voltage changes under normal operating conditions.

b. During the flick measurement, the measure time shall include that part of whole operation cycle in which the EUT produce the most unfavorable sequence of voltage changes. The observation period for short-term flicker indicator is 10 minutes and the observation period for long-term flicker indicator is 2 hours.



4.3.5 TEST SETUP

EUT


4.3.6 EUT OPERATING CONDITIONS Same as item 4.1.6.




231.3 Vrms / 0.047 Arms

POWER FREQUENCY 50 Hz

OBSERVATION PERIOD (TP) 10 min. POWER FACTOR 0.481


30 deg. C, 55 % RH, 1012 hPa TESTED BY Barry Lee

TEST PARAMETER MEASUREMENT VALUE LIMIT REMARKS

Pst 0.072 1.00 Pass Plt 0.072 0.65 Pass

Tdt (ms) 0.000 500 Pass dmax (%) 0.000 4% Pass

dc (%) 0.000 3.3% Pass

NOTE: (1) Pst means short-term flicker indicator. (2) Plt means long-term flicker indicator. (3) Tdt means maximum time that dt exceeds 3.3 %. (4) dmax means maximum relative voltage change. (5) dc means relative steady-state voltage change.




231.3 Vrms / 0.049 Arms






Pst 0.072 1.00 Pass Plt 0.072 0.65 Pass


dc (%) 0.000 3.3% Pass





231.3 Vrms / 0.048 Arms






Pst 0.072 1.00 Pass Plt 0.072 0.65 Pass


dc (%) 0.000 3.3% Pass



5 IMMUNITY TEST

5.1 GENERAL DESCRIPTION

Product Standard: EN 301 489-1 (2008-04), EN 301 489-3 (2002-08) EN 61000-4-2 Electrostatic Discharge – ESD:

8kV air discharge, 4kV Contact discharge, Performance Criterion B

EN 61000-4-3 Radio-Frequency Electromagnetic Field Susceptibility Test – RS: 80-1000 MHz, 1400-2700 MHz, 3V/m, 80% AM (1kHz), Performance Criterion A

EN 61000-4-4 Electrical Fast Transient/Burst - EFT, Power line: 1kV, Signal line: 0.5kV, Performance Criterion B

EN 61000-4-5 Surge Immunity Test: 1.2/50 us Open Circuit Voltage, 8 /20 us Short Circuit Current, line to line – 0.5 kV, line to earth - 1kV, Performance Criterion B

EN 61000-4-6 Conducted Radio Frequency Disturbances Test – CS: 0.15-80 MHz, 3Vrms, 80% AM, 1kHz, Performance Criterion A

Basic Standard, Specification, and Performance Criteria:

EN 61000-4-11 Voltage Dips: i) 0% residual for 0.5 cycle,

Performance Criterion B ii) 0% residual for 1 cycle,

Performance Criterion B iii) 70% residual for 25 cycle,

Performance Criterion B Voltage Interruptions: i) 0% residual for 250 cycle,

Performance Criterion B is required for EUT with battery back-up, Performance Criterion C is required for EUT without battery back-up.


5.2 GENERAL PERFORMANCE CRITERIA DESCRIPTION

The Requirement of Performance Criteria

1 Performance criteria for continuous phenomena applied to transmitters (CT)

Criterion A of the applicable class shall apply

2 Performance criteria for transient phenomena applied to transmitters (TT)

Criterion B of the applicable class shall apply

3 Performance criteria for continuous phenomena applied to receivers (CR)

Criterion A of the applicable class shall apply

4 Performance criteria for transient phenomena applied to receivers (TR)

Criterion B of the applicable class shall apply


The phenomena allowed during and after test in each criterion are clearly stated in the following table:

Class 1 SRD equipment Criteria During test After test

A

Operate as intended. No loss of function. For equipment type II the minimum performance shall be 12dB SINAD No unintentional responses

Operate as intended. For equipment type II the communication link shall be maintained No loss of function No degradation of performance No loss of stored data or user programmable functions

B May be loss of function (one or more) No unintentional responses

Operate as intended Lost function(s) shall be self-recoverable No degradation of performance No loss of stored data or user programmable functions


A

Operate as intended. No loss of function. For equipment type II the minimum performance shall be 6dB SINAD NO UNINTENTIONAL RESPONSES

Operate as intended. For equipment type II the communication link shall be maintained No loss of function No degradation of performance No loss of stored data or user programmable functions

B MAY BE LOSS OF FUNCTION (ONE OR MORE) No unintentional responses

Operate as intended Lost function(s) shall be self-recoverable No degradation of performance No loss of stored data or user programmable functions


A and B MAY BE LOSS OF FUNCTION (ONE OR MORE) No unintentional responses

Operate as intended, for equipment type II the communication link may be lost, but shall be recoverable by user No degradation of performance Lost functions shall be self-recoverable

NOTE: This device belongs to Type I, class 3 SRD equipment.


5.3 EUT OPERATING CONDITION

Same as 4.1.6


5.4 ELECTROSTATIC DISCHARGE IMMUNITY TEST (ESD)

5.4.1 TEST SPECIFICATION

Basic Standard: EN 61000-4-2 Discharge Impedance: 330 ohm / 150 pF Discharge Voltage: Air Discharge – 2, 4, 8 kV (Direct)

Contact Discharge – 2, 4 kV (Indirect) Polarity: Positive & Negative Number of Discharge: Minimum 20 times at each test point Discharge Mode: Single Discharge Discharge Period: 1 second minimum




CALIBRATED DATE

CALIBRATED UNTIL

NoiseKen, ESD Simulator ESS-100L(A) 0189C01491 July 26, 2010 July 25, 2011

Key Tek, ESD Simulator MZ-15/EC 9906323 June 11, 2010 June 10, 2011

Key Tek, ESD Simulator MZ-15/EC 0912389 Jan. 06, 2010 Jan. 05, 2011

NoiseKen, ESD Simulator

ESS-2002 ESS062521

2/244 May 07, 2010 May 08, 2011


2. The test was performed in ESD room A.


5.4.3 TEST PROCEDURE

a. Electrostatic discharges were applied only to those points and surfaces of the EUT that are accessible to users during normal operation.

b. The test was performed with at least ten single discharges on the pre-selected points in the most sensitive polarity.

c. The time interval between two successive single discharges was at least 1 second.

d. The ESD generator was held perpendicularly to the surface to which the discharge was applied and the return cable was at least 0.2 meters from the EUT.

e. Contact discharges were applied to the non-insulating coating, with the pointed tip of the generator penetrating the coating and contacting the conducting substrate.

f. Air discharges were applied with the round discharge tip of the discharge electrode approaching the EUT as fast as possible (without causing mechanical damage) to touch the EUT. After each discharge, the ESD generator was removed from the EUT and re-triggered for a new single discharge. The test was repeated until all discharges were complete.

g. At least ten single discharges (in the most sensitive polarity) were applied to the Horizontal Coupling Plane at points on each side of the EUT. The ESD generator was positioned at a distance of 0.1 meters from the EUT with the discharge electrode touching the HCP.

h. At least ten single discharges (in the most sensitive polarity) were applied to the center of one vertical edge of the Vertical Coupling Plane in sufficiently different positions that the four faces of the EUT were completely illuminated. The VCP (dimensions 0.5m x 0.5m) was placed vertically to and 0.1 meters from the EUT.

5.4.4 DEVIATION FROM TEST STANDARD No deviation No deviation As per client requests, the following discharge levels were also applied: Contact Discharge – 6, 8 kV for indirect contact discharge Air Discharge – 10, 12 kV for direct air discharge.


5.4.5 TEST SETUP

PS

EUT

Verticalcoupling plane

0.5mm Isolation Support

ESDGenerator

NearestWall Horizontal

coupling plane

Reference Ground Plane

0.1m1m

470kX4

80cm


NOTE:

TABLE-TOP EQUIPMENT The configuration consisted of a wooden table 0.8 meters high standing on the Ground Reference Plane. The GRP consisted of a sheet of aluminum at least 0.25mm thick, and 2.5 meters square connected to the protective grounding system. A Horizontal Coupling Plane (1.6m x 0.8m) was placed on the table and attached to the GRP by means of a cable with 940kΩ total impedance. The equipment under test, was installed in a representative system as described in section 7 of EN 61000-4-2, and its cables were placed on the HCP and isolated by an insulating support of 0.5mm thickness. A distance of 1-meter minimum was provided between the EUT and the walls of the laboratory and any other metallic structure.


5.4.6 TEST RESULTS(MODE 1~3)

MODE Mode 1~3 INPUT POWER 230Vac, 50Hz

ENVIRONMENTAL CONDITIONS (Start of Test)

25 deg. C, 45 % RH, 1012 hPa

ENVIRONMENTAL CONDITIONS (End of Test)

25 deg. C, 45 % RH, 1012 hPa

TESTED BY : Barry Lee

TEST RESULTS OF DIRECT APPLICATION

Discharge Level (kV)

Polarity (+/-) Test Point Contact

Discharge Air Discharge Performance Criterion

2, 4 +/- 1 ~ 2 NA NOTE (1) A 8 +/- 1 ~ 2 NA NOTE (2) B

2, 4, 8 +/- 3 NA NOTE (1) A Note: No conductive surfaces found, therefore no contact discharge was executed.

Description of test point: Please refer to following page for representative mark only.

TEST RESULTS OF INDIRECT APPLICATION

Discharge Level (kV)

Polarity (+/-) Test Point

Horizontal Coupling

Plane

Vertical Coupling

Plane

Performance Criterion

2, 4 +/- 1 ~ 4 NOTE (2) NOTE (2) B

Description of test point: 1. Front side 2. Right side 3. Left side 4. Rear side

NOTE: (1) There was no change compared with initial operation during the test.

(2) The EUT found disturbance noises on speaker during the test but could be self-recoverable after the test.

(3) The audio message of speaker was interrupted during the test but it could be recovered to normal operation by reset manually after the test. The air discharge level which over 8kV and contact discharge which over 4kV is not required by EN 301489-1 for RF equipment. It is according to the requirement of the manufacturer; the data of test result is only for manufacture’s reference.


DESCRIPTION OF TEST POINT

1

2


3


5.5 RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST (RS)


Basic Standard: EN 61000-4-3 Frequency Range: 80 MHz - 1000 MHz

1400 MHz - 2700 MHz Field Strength: 3 V/m Modulation: 1kHz Sine Wave, 80%, AM Modulation Frequency Step: 1 % of momentary frequency Polarity of Antenna: Horizontal and Vertical Antenna Height: 1.5m Dwell Time: 3 seconds




CALIBRATED DATE

CALIBRATED UNTIL

AR Power Amplifier 150W1000M3 311567 NA NA AR Power Amplifier 60S1G3M1 306171 NA NA AR LOG ANTENNA AT5080ANT 309740 NA NA BOONTON RF Voltage Meter

4232A 93801 Dec. 19, 2009 Dec. 18, 2010

R&S Signal Generator SML03 101159 Dec. 28, 2009 Dec. 27, 2010 Electric Field Probe FP6001 308178 Dec. 04, 2009 Dec. 03, 2010 ADT RS Test Workbench(Software)

ADT_RS_V7.5 NA NA NA


2. The test was performed in Chamber Room No. B. 3. The transmit antenna was located at a distance of 2.0 meters from the EUT.


5.5.3 TEST PROCEDURE

The test procedure was in accordance with EN 61000-4-3

a. The testing was performed in a fully-anechoic chamber.

b. The frequency range is swept from 80 MHz to 1000 MHz, 1400 MHz to 2700 MHz with the signal 80% amplitude modulated with a 1kHz sine wave.

c. The dwell time at each frequency shall not be less than the time necessary for the EUT to be exercised and to respond, but shall in no case be less than 0,5s.

d. The field strength level was 3V/m.

e. The test was performed with the EUT exposed to both vertically and horizontally polarized fields on each of the four sides.



5.5.5 TEST SETUP

For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. NOTE: TABLETOP EQUIPMENT The EUT installed in a representative system as described in section 7 of EN 61000-4-3 was placed on a non-conductive table 0.8 meters in height. The system under test was connected to the power and signal wire according to relevant installation instructions.

EUT

RF Amplifier RF Generator and control system

Monitoring system


5.5.6 TEST RESULTS(MODE 1~3) MODE Mode 1~3 INPUT POWER 230Vac, 50Hz


25 deg. C, 45 % RH, 1012 hPa


25 deg. C, 45 % RH, 1012 hPa

TESTED BY: Anderson Chen

Frequency

(MHz) Result Polarity Azimuth

Field Strength

(V/m)

Obser-

vation Performance

Criterion

80 -1000 PASS V&H 0 3

80 -1000 PASS V&H 90 3

80 -1000 PASS V&H 180 3

80 -1000 PASS V&H 270 3

NOTE A

1400 -2700 PASS V&H 0 3

1400 -2700 PASS V&H 90 3

1400 -2700 PASS V&H 180 3

1400 -2700 PASS V&H 270 3

NOTE A

NOTE: There was no change compared with initial operation during the test.

* The EUT request time out at 2419MHz during the test, but this band is exclusion band in EN 301489-17, the test result (request time out) is acceptable under this condition.


5.6 ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (EFT)


Basic Standard: EN 61000-4-4 Test Voltage: Power Line – 1kV, 2kV / 3kV / 4kV

Signal/Control Line – 0.5kV, 2kV / 1.5kV Polarity: Positive & Negative Impulse Frequency: 5 kHz Impulse Wave shape : 5/50 ns Burst Duration: 15 ms Burst Period: 300 ms Test Duration: 1 min.




CALIBRATED DATE

CALIBRATED UNTIL

EMC PARTNER, TRANSIENT TRA2000IN6 1211 Jan. 29, 2010 Jan. 28, 2011

EMC PARTNER, CN-EFT100 CN-EFT1000 662 NA NA

Adapter (EMC Partner) NA SU1ADA-002 NA NA

EMC Partner(Software) Test

Manger_V1.53 NA NA NA


2. The test was performed in EMS room B.

5.6.3 TEST PROCEDURE a. The EUT was tested with 1kV discharges to the AC power input leads and 0.5kV

discharges to the interconnect cables. b. Both positive and negative polarity discharges were applied. c. The length of the “hot wire” from the coaxial output of the EFT generator to the

terminals on the EUT should be 0.5m±0.05m.

d. The duration time of each test sequential was 1 minute. e. The transient/burst waveform was in accordance with EN 61000-4-4, 5/50ns.


5.6.4 DEVIATION FROM TEST STANDARD No deviation As per client requests, the following test voltage was applied: Power Line – 2 kV / Signal/Control Line – 2 kV

5.6.5 TEST SETUP

NOTE: l length between clamp and the EUT to be tested (should be 0.5 ± 0.05m)

(A) location for supply line coupling (B) location for signal lines coupling For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. NOTE:

EUTs, whether stationary floor-mounted or table top, and equipment designed to be mounted in other

configurations, shall be placed on a ground reference plane and shall be insulated from it by an

insulating support 0,1 m ± 0,01 m thick. A minimum distance of 0.5m was provided between the EUT

and the walls of the laboratory or any other metallic structure.




26 deg. C, 54 % RH, 1012 hPa


26 deg. C, 54 % RH, 1012 hPa

TESTED BY: Mike Hsieh I. POWER PORT

VOLTAGE (kV) TEST POINT POLARITY

(+/-) OBSERVATION PERFORMANCE CRITERION

1 L1 +/- NOTE (1) B 1 L2 +/- NOTE (1) B 1 L1-L2 +/- NOTE (1) B

NOTE: (1) The EUT found disturbance noises on speaker during the test but could be self-recoverable after the test.

There was no change compared with initial operation during the test.

(2) There were request time out during the test, but could be self-recoverable after the test.

(2) There were disturbance noises found via screen during the test but

self-recoverable after the test.


5.7 SURGE IMMUNITY TEST


Basic Standard: EN 61000-4-5 Wave-Shape: Combination Wave

1.2/50 us Open Circuit Voltage 8/20 us Short Circuit Current

Test Voltage: Power line-0.5 kV, 1 kV, 2 KV, 2.5KV Surge Input/Output: L1-L2 / L1-G / L2-G / L1,L2-G Generator Source Impedance:

2 ohm between networks 12 ohm between network and ground

Polarity: Positive/Negative Phase Angle: 0° /90°/180°/270° Pulse Repetition Rate: 1 time / 20 sec. Number of Tests: 5 positive and 5 negative at selected points




CALIBRATED UNTIL

EMC PARTNER, TRANSIENT TRA2000IN6 1211 Jan. 29, 2010 Jan. 28, 2011

EMC PARTNER, CDN-UTP8 CDN-UTP8 036 Jan. 28, 2010 Jan. 27, 2011

Adapter (EMC PARTNER) NA SU1ADA-002 NA NA

EMC Partner(Software) Test Manger_V1.53 NA NA NA

KeyTek, EMS Simulator EMC Pro 9712339 May 12, 2010 May 11, 2011 Adapter (EMC Pro) NA SU1ADA-001 NA NA KeyTek(Software) CEWare32_V3.0 NA NA NA




5.7.3 TEST PROCEDURE a. For EUT power supply:

The surge is to be applied to the EUT power supply terminals via the capacitive coupling network. Decoupling networks are required in order to avoid possible adverse effects on equipment not under test that may be powered by the same lines, and to provide sufficient decoupling impedance to the surge wave. The power cord between the EUT and the coupling/decoupling networks shall be 2 meters in length.

b. For test applied to unshielded unsymmetrically operated interconnection lines of EUT: The surge is applied to the lines via the capacitive coupling. The coupling / decoupling networks shall not influence the specified functional conditions of the EUT. The interconnection line between the EUT and the coupling/decoupling networks shall be 2 meters in length.

c. For test applied to unshielded symmetrically operated interconnection / telecommunication lines of EUT: The surge is applied to the lines via gas arrestors coupling. Test levels below the ignition point of the coupling arrestor cannot be specified. The interconnection line between the EUT and the coupling/decoupling networks shall be 2 meters in length.

5.7.4 DEVIATION FROM TEST STANDARD No deviation As per client requests, the following test voltage was applied: Power Line – 1 kV, 2 kV, 2.5 kV


5.7.5 TEST SETUP

EUTCombinationWave GeneratorCoupling &Decoupling Network

AC/DC Power Line(if any)

Signal Line(if any)

L 2m





26 deg. C, 54 % RH, 1012 hPa


26 deg. C, 54 % RH, 1012 hPa

TESTED BY: Mike Hsieh I. POWER PORT

VOLTAGE (kV) TEST POINT POLARITY

(+/-) OBSERVATION PERFORMANCE CRITERION

0.5, 1 L1-L2 +/- NOTE (1) A

NOTE: (1) There was no change compared with initial operation during the test. (2) The EUT were request time out during the test but could be

self-recoverable after the test.


5.8 IMMUNITY TO CONDUCTED DISTURBANCES INDUCED BY RF FIELDS (CS)


Basic Standard: EN 61000-4-6 Frequency Range: 0.15 MHz - 80 MHz Voltage Level: 3 Vr.m.s. Modulation: 1kHz Sine Wave, 80%, AM Modulation Frequency Step: 1 % of momentary frequency Coupled Cable: Power Mains, Unshielded

Signal / Control Line Coupling Device: CDN-M2 (2 wires), CDN-T4




CALIBRATED DATE

CALIBRATED UNTIL

R&S Signal Generator SML 01 102731 Dec. 21, 2009 Dec. 20, 2010 AR Amplifier 75A250AM2 307297 NA NA BOONTON RF Voltage Meter 4232A 93801 Dec. 19, 2009 Dec. 18, 2010 LUTHIE EM Injection Clamp EM-101 35453 May 25, 2010 May 24, 2011 FCC CDN M2 FCC-801-M2-16A 03048 Jan. 11, 2010 Jan. 10, 2011 FCC CDN M3 FCC-801-M3-16A 03055 Jan. 12, 2010 Jan. 11, 2011 Fischer Custom Communications Inc Coupling Decoupling Network

FCC-801-T2 02025 Oct. 27, 2009 Oct. 26, 2010

Fischer Custom Communications Inc Coupling Decoupling Network

FCC-801-T4 02030 Oct. 27, 2009 Oct. 26, 2010

Fischer Custom Communications Inc Coupling Decoupling Network

FCC-801-T8 02036 Oct. 27, 2009 Oct. 26, 2010

ADT CS Test Workbench(Software)

ADT_CS_V7.4.2 NA NA NA


2. The test was performed in Chamber Room No. B.


5.8.3 TEST PROCEDURE a. The test was performed with the test generator connected to each of the coupling

and decoupling devices in turn, while the other non-excited RF input ports of the coupling devices are terminated by a 50-ohm load resistor.

b. The frequency range is swept from 150 kHz to 80 MHz, using the signal level established during the setting process and with a disturbance signal of 80 % amplitude. The signal is modulated with a 1 kHz sine wave, pausing to adjust the RF signal level or the switch coupling devices as necessary. Where the frequency is swept incrementally, the step size shall not exceed 1 % of the preceding frequency value.

c. The dwell time of the amplitude modulated carrier at each frequency shall not be less than the time necessary for the EUT to be exercised and to respond, but shall in no case be less than 0,5 s. The sensitive frequencies (e.g. clock frequencies) shall be analyzed separately.

d. Attempts was made to fully exercise the EUT during testing, and to fully interrogate all exercise modes selected for susceptibility.



5.8.5 TEST SETUP

NOTE: 1. The EUT clearance from any metallic obstacles shall be at least 0.5m.

2. All non-excited input ports of the CDNs shall be terminated by 50Ω loads. 3. The EUT is setup 0.1m above Reference Ground Plane 4. The CDNs and / or EM clamp used for real test depends on ports and cables

configuration of EUT.

For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. FLOOR-STANDING EQUIPMENT The equipment to be tested is placed on an insulating support of 0.1 meters height above a ground reference plane. All relevant cables shall be provided with the appropriate coupling and decoupling devices at a distance between 0.1 meters and 0.3 meters from the projected geometry of the EUT on the ground reference plane.



MODE Mode 1~3 INPUT POWER 230Vac, 50Hz


25 deg. C, 45 % RH, 1012 hPa


25 deg. C, 45 % RH, 1012 hPa

TESTED BY: Barry Lee FOR MAINS POWER:

Frequency (MHz)

Voltage level

(Vr.m.s.) Cable Injection

Method Obser-vation Performance Criterion

0.15 –80 3 AC power line CDN-M2 NOTE (1) A

NOTE: (1) There is no change compared with the initial operation during the test.


5.9 VOLTAGE DIP/SHORT INTERRUPTIONS/VOLTAGE VARIATIONS (DIP) IMMUNITY TEST


Basic Standard: EN 61000-4-11 Test Duration Time: Voltage Dips:

i) 0% residual voltage for 0.5 cycle ii) 0% residual voltage for 1 cycle, iii) 70% residual voltage for 25 cycles,

Voltage Interruptions: i) 0% residual voltage for 250 cycles

Interval between Event: Minimum ten seconds Phase Angle: 0°/180° Test Cycle: 3 times




CALIBRATED UNTIL

EMC PARTNER, TRANSIENT TRA1Z332N 1121 Jan. 29, 2010 Jan. 28, 2011

Adapter (EMC PARTNER) NA SU1ADA-002 NA NA

EMC Partner(Software) Test Manger_V1.53 NA NA NA

KeyTek, EMS Simulator EMC Pro 9712339 May 12, 2010 May 11, 2011 Adapter (EMC Pro) NA SU1ADA-001 NA NA

KeyTek(Software) CEWare32_V3.0 NA NA NA




5.9.3 TEST PROCEDURE The EUT shall be tested for each selected combination of test levels and duration with a sequence of three dips/interruptions with intervals of 10 s minimum (between each test event). Each representative mode of operation shall be tested. Abrupt changes in supply voltage shall occur at zero crossings of the voltage waveform.

5.9.4 TEST SETUP

EUTVoltage Dips Generator AC Power Line




MODE Mode 1~3 INPUT POWER 240Vac / 100Vac / 230Vac, 50 Hz


26 deg. C, 54 % RH, 1012 hPa


26 deg. C, 54 % RH, 1012 hPa

TESTED BY: Mike Hsieh

Input Power for testing: 240Vac, 50 Hz (Maximum Voltage)

VOLTAGE % RESIDUAL

PERIODS (cycle)

RESULTS OBSERVATION PERFORMANCE CRITERION

0 0.5 PASS NOTE (1) A

0 1 PASS NOTE (1) A

70 25 PASS NOTE (1) A

0 250 PASS NOTE (2) B

Input Power for testing: 100Vac, 50 Hz (Minimum Voltage)

VOLTAGE % RESIDUAL

PERIODS (cycle)



0 1 PASS NOTE (1) A



Input Power for testing: 230Vac, 50 Hz (Normal Voltage)

VOLTAGE % RESIDUAL

PERIODS (cycle)



0 1 PASS NOTE (1) A



NOTE: (1) There is no change compared with the initial operation during the test. (2) The EUT shut down during the test, but could be self-recoverable after

the test.


6 PHOTOGRAPHS OF THE TEST CONFIGURATION

CONDUCTED EMISSION TEST


HARMONICS EMISSION TEST & VOLTAGE FLUCTUATIONS AND FLICKER TEST

ESD TEST


RS TEST

EFT TEST


SURGE & VOLTAGE DIPS

AND INTERRUPTIONS TEST

CONDUCTED SUSCEPTIBILITY TEST


7 APPENDIX - INFORMATION ON THE TESTING LABORATORIES

We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025:

Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: www.adt.com.tw/index.5/phtml. If you have any comments, please feel free to contact us at the following:

Linko EMC/RF Lab: Tel: 886-2-26052180 Fax: 886-2-26052943

Hsin Chu EMC/RF Lab: Tel: 886-3-5935343 Fax: 886-3-5935342

Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: 886-3-3183232 Fax: 886-3-3185050

Email: [email protected] Web Site: www.adt.com.tw

The address and road map of all our labs can be found in our web site also. --- END ---

http://www.adt.com.tw/index.5/phtml

mailto:[email protected]

http://www.adt.com.tw

Page 1

CONSTRUCTION PHOTOS OF EUT

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Documents

EMC TEST REPORT - logitech.com EN30148… · Report No.: RM990811E03 6 Report Format Version 3.0.3 CERTIFICATION - Continued The test record, data evaluation & Equipment Under Test