Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
|| | A
BO
UT
BO
A® T
EC
HN
OLO
GY
|| |
INS
TR
UC
TIO
N M
AN
UA
L
Boa
Tec
hnol
ogy
Inc.
is t
he d
evel
oper
of t
he B
oa L
acin
g S
yste
m
and
man
ufac
ture
r of
Boa
Lac
e R
eels
, Boa
Lac
es, a
nd B
oa L
ace
Gui
des.
We
sell
our
line
of B
oa c
ompo
nent
s to
man
ufac
ture
rs o
f fin
e bi
ke s
hoes
, sno
wbo
ard
boot
s, a
nd o
ther
ath
letic
foot
wea
r who
un
ique
ly d
esig
n th
e sy
stem
into
the
ir hi
gh p
erfo
rman
ce fo
otw
ear.
Boa
’s o
nly
bus
ines
s, a
nd o
ur s
ole
focu
s, is
the
con
tinua
l im
pro
vem
ent
of o
ur c
losu
re c
omp
onen
ts a
nd m
anuf
actu
ring
exce
llenc
e. B
oa T
echn
olog
y w
as fo
und
ed a
nd is
bas
ed in
C
olor
ado,
in t
he h
eart
of t
he R
ocky
Mou
ntai
ns.
We
use
our
pro
duc
ts d
aily
.
IMPORTANT: Change one shoelace at a time and use the other shoe as a guide.
FOLLOW THESE STEPS TO REMOVE THE REEL FROM THE BOOT Use the lace tool to remove the knob and laces. (SEE STEPS 3A - 3F BELOW)
Insert the lace tool into the hole in the reel as shown.The end of the lace tool will engage the hole in thebayonet locking arm.
With the lace tool, pull the locking arm away from thecenter of the reel and rotate the reel CLOCKWISE.
Press on the reel from the backside of the tongue topush it out of the bayonet.
Align the smallest metal tab on the reelwith the smallest slot on the bayonetand insert the reel into the bayonet.
Rotate the reel COUNTER CLOCKWISEabout 10 degrees until it “clicks” into place.
Now go to step 3G to install lacesand attach knob.
5mm
| | | HOW TO REPLACE SERIES 20, SERIES 30 + COILER MODEL REELS:
1
2 FOLLOW THESE STEPS TO INSERT A NEW REEL INTO THE BAYONET
HOW TO REPLACE BOA LACES:
Push knob in.
| | |BOATECHNOLOGY.COM
3
A Loosen screw inside knob with lace tool.
B Remove knob.C
BAYONET
LACE TOOL
BAYONET
BAYONET LOCKING ARM
SMALLEST TAB GOES HERE
LACE TOOL
Pull out slack in lace.D Line up holes using plastic end of lace tool.
E Loosen (but do not remove) set screws, then remove lace.
F
KNOB
LACE CABLE
COILER ONLY
HOLD TENSION ON LACETO KEEP FROM REWINDING
DON’TPIVOTTOOL
SET SCREWS
SET SCREWS
Insert new lace untilvisible in viewing hole.
G Tighten set screws.H Replace knob andtighten back up.
I
LACE CABLE END
ENLARGED VIEW
VIEWING HOLE
SET SCREW
COILER ONLY
PULL OUT + DISCARDL SHAPED PIN AFTERTIGHTENING SCREWS
SE
RIE
S 2
0 |
SE
RIE
S 3
0 |
CO
ILE
R