S U B M I T T A L S H E E T

Revised: December 2016 FX Fabric Guard Technical Data© “Fire Retardant Coatings of Texas” & “FRCT” Logo are federally registered trademarks of Fire Retardant Coatings of Texas®, LLC

Fire Retardant Coatings of Texas®, LLC 1150 Blue Mound Rd West #403 Haslet, Texas 76052 Office (817) 710-5233 Fax (817) 439-8385

Interior Fire Retardant Spray for cotton, cotton/polyester, denim, Canvas and Terry Cloth. Artificial Silk Foliage, Décor, Wall Tapestries, Window Shades, etc. Limited exterior use

(NON-ELEMENT CONTACT). Meets 16 CFR 1500.3 Federal Hazardous Substances Act (FHSA) of the

Consumer Product Safety Commission (CPSC)

Testing SFM 1237.1 • NFPA 701 • CAN/ULC S109-03 Federal Motor Vehicle Safety Standard 302

ASTM E84 (UL723) CLASS A FIRE RETARDANT NOT RECOMMENDED FOR CLOTHING OR BEDDING

Application Process: Material to be treated must be clean & dry before treating. Agitate product before and during application. Apply

FX FabricGuard as it’s received. Apply by spraying with a low pressure hand pump sprayer at a rate of 350 / 400 sf per gallon or you can use a sponge to dampen the fabric. Apply until damp as the fabric will absorb the fire retardant. Drying

time will vary 4-12hrs depending on weather, density of fabric and humidity. Clean up with soap & water.

Cleaning / Retreating: Your fire retardant treated fabric can be dry-cleaned (dry chemicals only) as recommended by the fabric manufacturer, however, once the treated fabric has been cleaned 3-4 times it will need to be retreated. Typically, the flame retardancy of topically treated fabric is certified depending on handling or cleaning for 3 years, though the actual length of time in which the treatment remains

effective will vary based on the number of times it is cleaned, handled and/or environmental conditions. Treated Fabric (floor coverings / wall coverings) that aren’t dry cleaned do not require retreatment.

Warranty: Please visit www.frctexas.com for warranty information

NON TOXIC ENVIRONMENT SAFE NON CORROSIVE

PH Range: 4.5 – 5 % Shelf Life 3 yrs stored <125°

ONE COAT APPLICATION

Anti-Bacterial: Good

350-400 sf per gal DO NOT DILUTE DON’T LET FREEZE TRANSPARENT

CALIFORNIA REGISTERED

C-25901

WARNING: KEEP THIS AND ALL CHEMICALS OUT OF CHILDRENS REACH AS WITH ANY PRODUCT, THIS PRODUCT MAY CAUSE EYE AND/OR SKIN IRRITATION - ALWAYS WEAR PERSONAL PROTECTION EQUIPMENT

WHEN HANDLING THIS OR ANY CHEMICALS

A colorant can be added for validation of treatment

FX LumberGuard XT is Leach Resistant FX LumberGuard XT is not a sealer or preservative FX LumberGuard XT can be applied to preservative treated lumber, if the lumber is dry Retreatment will vary 2-5 years depending on the ambient temperature, wind, rain, snow, foot traffic, etc. Use for porous Lumber and Plywood, Shake Shingles, Thatching, Bamboo and similar materials.

Application Process: Material to be treated must be clean & dry before treating. Agitate product before and throughout application. Apply as it’s

received. Maybe sprayed on with a hand pump sprayer, rolled on or brushed on at a rate of 300-350 sf per gallon depending on material being treated. (Vertical spraying) Start from the bottom and work up as there is less run off this way. Drying time

will vary 8-32hrs depending on weather and temperature. Rinse equipment & wash hands with soap.

Field Testing: When the observation of the treatment and/or field testing is required, field testing must be conducted as follows:

The treated substrate will not have distinctive observable features. To ensure the substrate has been treated properly, the treated substrate must be field tested, the flame from a small fire source (propane torch) is applied to a treated and untreated sample of substrate for a period of not less than 15 seconds. The presence of the treatment must be observable through the comparison of the reactions of the substrates to the flame.

Presence of the coating can be observed when the coating begins to form a black char layer.

Meets 16 CFR 1500.3 FHSA of the Consumer Product Safety Commission (CPSC) as Non-Hazardous / Non-Toxic WARNING: KEEP THIS AND ALL CHEMICALS OUT OF CHILDRENS REACH - AS WITH ANY PRODUCT, THIS MAY CAUSE EYE AND/OR SKIN IRRITAION -

ALWAYS WEAR PERSONAL PROTECTION EQUIPMENT WHEN HANDLING THIS OR ANY CHEMICALS.

NOTE: Degradation: Design Values of lumber or plywood are not effected due to not impregnating with a salt base chemical or kiln drying after treatment.

Revised: June 2015 FX LumberGuard XT – “Fire Retardant Coatings of Texas” & “FRCT” Logo are federally registered trademarks of

Fire Retardant Coatings of Texas®, LLC

T E C H N I C A L D A T A

Fire Retardant Coatings of Texas®, LLC 1150 Blue Mound Rd West #403

Haslet, Texas 76052 Office (817) 710-5233 Fax (817) 439-8385

www.frctexas.com

SUBMITTAL SHEET

Listed to ASTM E84 & ASTM E2768

SYP, SPF, Hem Fir & Doug Fir Lumber & SPF and SYP Plywood

CSI Divisions 06 05 73.13 Fire Retardant Wood Treatment &

CSI 09 96 43 Fire Retardant Coatings Additional Testing and Standards CAN/ULC S102 • NFPA 255/703 •

ANSI/UL 723 • UBC 42.1 Intertek Warnock Hersey Certification

is equivalent to “UL Certification” Intertek Code Compliance Research

Report (CCRR) is equivalent to “ICC-ESR”

Technical Data • FSI: <10 • CLASS A • 300/350sf per gal

• 1 Coat Application • Non Toxic • Non Halogenated • No PBDE’s • No Carcinogens • No Added Formaldehyde

• Environment Safe • Odorless • 3 year shelf life • Non Corrosive • Stainable/Paintable • User Friendly •

Apply between 45° to 95°

Distributed by

#106 4848 275th Street, Aldergrove, B.C. V4W 0A3604-856-8932 www.fireretardantcanada.com

Interior or Exterior Use

Construction Specifications (CSI) available at www.arcat.com/sd/divs/sd_div09.shtml (item 09 96 43)

#106 - 4848 275th Street Aldergrove, B.C. V4W 0A3Info@fireretardantcanada.com www.fireretardantcanada.com250-938-3876

A colorant can be added for validation of treatment

FX LumberGuard XT is a Non Leachable fire retardant wood treatment, over coating with a wood protectant or painted over is HIGHLY Recommended to prolong the life of the material treated.

FX LumberGuard XT can be applied to preservative (green) treated lumber, if the lumber is dry and above ground contact.

FX Lumber Guard XT is NOT a Preservative

Also used for porous Lumber and Plywood, Cedar, Shake Shingles, Redwood, Reclaimed Barn Wood, Thatching, Bamboo and Engineered Materials (OSB, LVL’s, PSL’s and similar materials with limited moisture exposer).

Application Process:

Material to be treated must be clean & dry before treating. Agitate product before and throughout application. Apply as it’s received. Maybe sprayed on with a hand pump sprayer, rolled on or brushed on at a rate of 300-350 sf per gallon depending on material being treated.

(Vertical spraying) Start from the bottom and work up as there is less run off this way. Drying time will vary 8-32hrs depending on weather and temperature. The maximum moisture content for the substrate to be treated is 15 percent for dimensional lumber, 19 percent

for plywood, and 16 percent for oriented strand board (OSB).

Field Testing: When the observation of the treatment and/or field testing is required, field testing must be conducted as follows:

The treated substrate will not have distinctive observable features. To ensure the substrate has been treated properly, the treated substrate must be field tested, the flame from a small fire source (propane torch) is applied to a treated and untreated sample of substrate for a period of not less than 15 seconds. The presence of the treatment

must be observable through the comparison of the reactions of the substrates to the flame. Presence of the coating can be observed when the coating begins to form a black char layer.

An exterior grade paint / sealer may be applied over FX Lumber Guard XT to assist in prolonging the life of the wood.

Meets 16 CFR 1500.3 FHSA of the Consumer Product Safety Commission (CPSC) as Non-Hazardous / Non-Toxic WARNING: KEEP THIS AND ALL CHEMICALS OUT OF CHILDRENS REACH - AS WITH ANY CHEMICAL, THIS MAY CAUSE EYE AND/OR

SKIN IRRITAION - ALWAYS WEAR PERSONAL PROTECTION EQUIPMENT WHEN HANDLING THIS OR ANY CHEMICALS.

Degradation: Design Values of lumber or plywood are not affected due to not impregnating with a salt base chemical or kiln drying after treatment.

Revised: December 2016 – “Fire Retardant Coatings of Texas” & “FRCT” Logo are federally registered trademarks of

Fire Retardant Coatings of Texas®, LLC

T E C H N I C A L D A T A

Fire Retardant Coatings of Texas®, LLC 1150 Blue Mound Rd West #403

Haslet, Texas 76052 Office (817) 710-5233 Fax (817) 439-8385

www.frctexas.com

TECHNICAL DATA SUBMITTAL SHEET

Certified Listed to ASTM E84 & ASTM E2768 Class A rated

SYP, SPF, Hem Fir & Doug Fir Lumber & SYP / Fir Plywood & OSB

CSI Divisions 06 05 73.33 Fire Retardant Wood Treatment &

CSI 09 96 43 Fire Retardant Coatings Additional Testing, Processing and

Standards ASTM D2898 • CAN/ULC S102

NFPA 255/703 • ANSI/UL 723 • UBC 42.1 for Engineered Materials, Cedar, Redwood,

Bamboo and Reclaimed Woods.

Technical Data Exterior or Interior Application

• FSI <25 • SGI / SDI <200 • Natural Mold & Insect Inhibitor • 1 Coat Application • Non Toxic • Non Halogenated

• No PBDE’s • No Carcinogens • Storage Temp >45° F • Environment Safe • 3-year shelf life • Non Corrosive

• Stainable/Paintable • Application Temp 45-95°F • PH Range. 4.5-5%