Dd-wrt Modificacion de Memoria MMC

7/27/2019 Dd-wrt Modificacion de Memoria MMC

1/5

DD-WRT Community Contact

Development News Forum Wiki Bugtracker Blog

Board FAQ Search Memberlist Usergroups Register

Goto page 1, 2, 3, 4 Next View previous topic ::View next topic

SD/MMC mod for the WRT54G-TM

DD-WRT Forum Forum Index -> Broadcom SoC based Hardware

Author Mess age

DoramiusDD-WRT User

Joined: 29 Aug 2008Posts: 311

Posted: Fri Nov 07, 2008 11:10 Post subject: SD/MMC mod for the WRT54G-TM

This mod may also work f or some WRT54GL routers, as I followed information that was primarily written for modding the WRT54GL. Much of what I fo und came from [url=the-mesh.org]The Mesh Dot Or g[/url] on this page: http://www.the-mesh.org/tiki-index.php?page=LinksysSDCard#Solder_points

[Click on images below to view larger image]

I'll mostly post pictures of the build I did. I had gone t o Walmart and picked up a cheap Targus HighSpeed USB > SD/SDHC/MMC adapter. The case opened up really easy.

I went straight to work removing all components, except for the card slot, from the board. Solder braid works best, but even after I wicked off the leads to the chip, I still had to gently use a razor blade to slice under the leads to remove it. I also used a continuitytester to make sure there were no shorts from pin to pin. Pins 3 & 6 WILL short, but they are both Ground/Common. So no worries there.

Here's the pinout for the SD card and the GPIO points:

Now where the GPIO points are....? These little images made them quite easy to find. I still tested them to make sure they were correct. And they were.

However, Instead of the ground at the JTAG headers, I f ound and tested this large, unused, copper pad for ground. It's the middle pad that comes out to a 'T'. (arrow off to t he right)

Now I had so me ribbon cable left ov er fro m when I built my JTAG/TTL box.

I needed to mount the SD slot somewhere and chose over ports 1&2, as the bracket served as a nice size mounting point. I lightly sanded the top, so it would take solder. And then placed the SD slot between to place solder at points for a hold-down.

APC Backups from $29www.re-UPS.ca

Save up to 75% on major brand UPS Systems & Batteries

Quick Links

converted by Web2PDFC onvert.com
http://www.web2pdfconvert.com/?ref=PDFhttp://www.web2pdfconvert.com/?ref=PDFhttp://www.the-mesh.org/tiki-index.php?page=LinksysSDCard#Solder_pointshttp://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=225175&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=225175&sid=a9ffc1773346466c6d1032f3f2a649d9#225175http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&view=next&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&view=previous&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=15&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=45&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=30&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=15&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewforum.php?f=1&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/index.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=reply&t=40464&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=newtopic_wtf&f=1&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=register_wtf&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/groupcp.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/memberlist.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/search.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/faq.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/index.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/blog/http://dd-wrt.com/bugtracker/http://dd-wrt.com/wikihttp://dd-wrt.com/phpBB2/http://dd-wrt.com/dd-wrtv3/community/developmentnews.htmlhttp://dd-wrt.com/dd-wrtv3/contact.htmlhttp://dd-wrt.com/dd-wrtv3/community/developmentnews.htmlhttp://dd-wrt.com/dd-wrtv3/


2/5

I then soldered the ribbon cables to the SD slot pins on the top of the mini-board. Not an e asy job as they are pretty small. Next I took a piece of thin double sided tape and placed it on the botto m of the mini-board the SD slot was attached to. This did 2 things.Kept the port bracket from shorting the pads on the mini-board and stuck the board t o the bracket. {Note} make sure your mini-board is not all the way to the other edge. You should be about 2mm from the edge as t he case will slide about that distance ov er theedge of the bracket. I then to ok 2 solid strands fr om a twisted pair cable, stripped them, twisted the m together, and soldered the m together. This was my hold-down. I soldered the inside firs t, placed the mini-board on the bracket, and t hen soldered the other endat the edge o f port one on the bracket. I left a bit of a tail so I could use pliers to pull the end firmly down to make sure it would solidly hold the slot in place. Sliding the cards in and out can cause quite a beating. The double sided tape and the ho ld-down will makesure the slot stays firmly affixed.

I then soldered the points as shown. Also note, that there are through-hole points near the LEDs. Use those as you don't want to remove an LED, or cause any damage to them. It also keeps the wire underside as some cases have plastic parts that mount rightover the LEDs.

Next I brought o ut my trusty Dremmel and, after care ful measurement, cut out the slot in the case where the car d would go in. I made the slot about 2mm wider than the card on the s ides. Giving a 1mm space on either side.

Time to put it all together.

Now that it's all done, phys ically, it's time to plug in an SD or MMC card and t est it out with a P C.When I first plug it in, I not ice it takes a little longer to load this first time. The SES light may or may not come on and flash a f ew times. This is normal. Just wait for the Power, Wireless, and the port light, corresponding to t he port your PC is connected to , are all onand steady. If the SES light came on, with for it to steady. Log into the DD-WRT page. Go to the Administration tab and scroll down to MMC/SD Card Support areas. Enable it. I left the GPIO pins select at auto and it worked fine, but if you need to, the GPIO pointsare listed above. I also enabled the JFFS2, and you can also enable CIFS Automount, if desired.

Once you apply the settings, let it complete to reload the page. it may take a few minutes. The page may come back with data missing. Again, this is normal. Go to your router and press and hold the reset button for 30 seconds, while still holding the reset button,unplug the power and wait 5 more seconds bef ore releasing the r eset button. Now plug the power back in and let the unit load.

Again, this may take a few moments as it formats the card. The SES will probably come on, and rapidly flash for a bit, then turn solid. Wait for the Power, Wireless, and the PC connected port light to come on, steady. Now log back into DD-WRT and check the status.Any enabled items should show space usage listed.

The default for DD-WRT is 4096KB. There's a way to change it for 1GB cards, but I haven't had a chance to do it yet. When I do, I'll amend to this tutorial.

Enjoy!

Last edited by Doramius on Sat Nov 08, 2008 2:31; edited 2 times in total

Back to top

Sponsor

Shawn360DD-WRT Guru

Joined: 26 Jul 2008Posts: 1237

Posted: Fri Nov 07, 2008 11:39 Post subject:

Why not use the ground at the serial header?

Back to top

DoramiusDD-WRT User


http://www.web2pdfconvert.com/?ref=PDFhttp://www.web2pdfconvert.com/?ref=PDFhttp://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=225263&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=225263&sid=a9ffc1773346466c6d1032f3f2a649d9#225263http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=41462&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=41462&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=225186&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=225186&sid=a9ffc1773346466c6d1032f3f2a649d9#225186http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9


3/5


I'm trying to find alternative points t o the headers. This way I can still use a JTAG or ser ial header. I'll probably update the 3 .3V wire at a late r time, but as you can see, locally I f inished this project about 3am.

Back to top

jmh9072DD-WRT Guru

Joined: 04 Sep 2007Posts: 800Location: Ohio


That's awesome! Great job!__________ _______WRT54G v3 - v24 r14471M NEWD Eko - APWRT350N v1.0WRT600N v1.1 - halfway there!Se7en is Darker...

Back to top

gix

DD-WRT Novice

Joined: 23 Aug 2008

Posts: 18

Posted: Sun Nov 09, 2008 9:59 Post subject:

shouldnt it look more like this?

Back to top

DoramiusDD-WRT User


Posted: Sun Nov 09, 2008 11:47 Post subject:

I grabbed the snap shot with just the adapter installed. I had a Micro SD and the SD adapter and forgot to insert the micro card. You can see that in one of the pictures.

Back to top

Erich2050DD-WRT Novice

Joined: 10 Feb 2007Posts: 7

Posted: Mon Dec 01, 2008 6:01 Post subject:

i tried to format my sd card on my debian system, because my wrt54g wasn't able to do it by itself. so i typed ...

Code:

umount /dev/sdcmkfs.ext2 -L sdkarte /dev/sdc

... everything looked fine on debian and so i pluged my sd card into my router to see if it works. but it did't :(

i used the micro sd card of my nokia 6300 with an adapter

what could i made wrong?

sry for my bad english

InternetPCN - Router Status_1228110359455.png

Description: screenshot of my router status (including the space usage)

Filesize: 26.46 KB

Viewed: 41546 Time(s)

InternetPCN - Administration_1228110392114.png

Description: screenshot of my administration panel

Filesize: 28.64 KB

Viewed: 41546 Time(s)

http://www.web2pdfconvert.com/?ref=PDFhttp://www.web2pdfconvert.com/?ref=PDFhttp://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=234737&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=234737&sid=a9ffc1773346466c6d1032f3f2a649d9#234737http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=225796&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=225796&sid=a9ffc1773346466c6d1032f3f2a649d9#225796http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43116&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43116&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=225786&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=225786&sid=a9ffc1773346466c6d1032f3f2a649d9#225786http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=23434&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=23434&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=225264&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=225264&sid=a9ffc1773346466c6d1032f3f2a649d9#225264http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9


4/5

Back to top

Doramius

DD-WRT User


Posted: Mon Dec 01, 2008 16:58 Post subject:

On some of thos e micro cards, I am not sure if t he drivers are properly recognized. I had some issues with some micro cards to o. I had initially tried a Patr iot 1GB micro SD card with an adapter, but it wasn't working and I got v arious results. Do not use anythinglarger than 1GB, as those do not seem to work either. I used a PNY SD card and that wor ked.

Back to top

grantchDD-WRT Novice

Joined: 17 Dec 2008Posts: 10

Posted: Wed Dec 17, 2008 18:26 Post subject:

I had the same issue with my mod. My 2GB MicroSD card with adapter and it always showed up a 2MB or 4MB but it actually was not mounted at all. Using dmesg showed the mmc was not detecte d. I had an old 32MB card t hat I put in and it worked with no problemand DD-WRT showed 27 MB free. I read somewhere that someone changed from a 1A power adapter to a 5A one and the bigger cards worked.

Grantch

Back to top

trilithDD-WRT Novice

Joined: 10 Oct 2008

Posts: 20


grantch wrote:

I read somewhere that someone changed from a 1A power adapter to a 5A one and the bigger cards worked.

Grantch

hmm, care to elaborate ? are you referring to the AC power adaptor of router ?

Back to top




trilith wrote:

grantch wrote:

I read somewhere that someone changed from a 1A power adapter to a 5A one and the bigger cards worked.

Grantch

hmm, care to elaborate ? are you referring to the AC power adaptor of router ?

Yes the AC power adapter

Here is the posthttps://dd-wrt.com/phpBB2/viewtopic.php?p=59574

GrantchHere also is a post from someone having problems with WRT54G-TM over 64 MB

https://www.dd-wrt.com/phpBB2/viewtopic.php?p=193994

This is essentialy the problem I had although I only have a 32MB and a 2GB to tr y

Back to top

DoramiusDD-WRT User



You're not really changing the voltage, but increasing the amperage that can be used. This is understandable. Some flash cards over 512MB require a little more amperage. Some slower cards might not. Some routers are eve n coming with 500mA power supplies.Without any mod, I've noticed those burning out quite easily. The 1A adapters may not have enough juice to support the larger draw of current.

Back to top




Correct I just need to boost the avaiable current and not change any voltages. I think mine came with a 1A power supply. Does anyone know if these power supplies can be modded, or what mechinism they use to limit current? When you say they burn out do youknow what componant fails in the AC supply?

Back to top

DoramiusDD-WRT User



It's usually the transformer itself. The transformer is wound to appropriately step down the voltage and current. Sometimes there's a resistor and capacitor to help filter a bit before the bridge to convert to DC, and those are known to fail at times, but aren't usuallythe problem. What happens is if t here is too much current draw, the unit literally burns out. It's like forcing a horse to run it's fastest , constantly, without giving it a re st... .and then try ing to push it faster. By limiting the Amperage, it limits the modding to theirdevices. Almost like why they keep reducing the flash and RAM in their devices.

All you need is a 12VDC power supply that has a rating of 5A or more (5A is sometimes shown as 5000mA for those that may not be as technically inclined). A device will only use the current it requires. So if you get a 12VDC power supply with a 20A rating (it'll be alarge looking block for that kind of amperage too), if your device only requires 2A, it'll be fine using the 20A power supply. If the device requires 3A, and you use a 500mA power supply, then you'll either burn out the power supply, the device won't have enoughcurrent flow to work, or both.

FYI - Generally, the smaller the amperage a power supply s upports, the s maller the power supply will be. The more amperage a power supply supports, the bigger the power supply t ends to be.

Here's one more snippet of advice. PC power supplies tend to have their 12VDC rails run somewhere between 10A-20A. Some of the MUCH older PSUs may not need to be connected to a MoBo to turn on. Most ATX PSUs require some sort of connection to power on.I don't remember the pins to short a resistor across, but you could get a Cheap PSU tester for $15-20 and connect it to an old PC PSU, to give you a nice 12VDC with enough amperage. Might even be able to power a few other devices too. I have a PSU that Iadded USB ports connected to the 5VDC line to charge an iPod & iPhone.

I know someone else who used a PC PSU to power an HO scale model railroad. I didn't know that was possible, but pret ty cool ingenuity.

Back to top

http://www.web2pdfconvert.com/?ref=PDFhttp://www.web2pdfconvert.com/?ref=PDFhttp://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=241070&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=241070&sid=a9ffc1773346466c6d1032f3f2a649d9#241070http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=50172&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=50172&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=241032&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=241032&sid=a9ffc1773346466c6d1032f3f2a649d9#241032http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=241013&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=241013&sid=a9ffc1773346466c6d1032f3f2a649d9#241013http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=50172&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=50172&sid=a9ffc1773346466c6d1032f3f2a649d9https://www.dd-wrt.com/phpBB2/viewtopic.php?p=193994https://dd-wrt.com/phpBB2/viewtopic.php?p=59574http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=240967&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=240967&sid=a9ffc1773346466c6d1032f3f2a649d9#240967http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=46056&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=46056&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=240957&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=240957&sid=a9ffc1773346466c6d1032f3f2a649d9#240957http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=50172&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=50172&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=240951&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=240951&sid=a9ffc1773346466c6d1032f3f2a649d9#240951http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=43528&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=234867&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=234867&sid=a9ffc1773346466c6d1032f3f2a649d9#234867http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=14354&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=14354&sid=a9ffc1773346466c6d1032f3f2a649d9


5/5

more nsDD-WRT User

Joined: 18 Nov 2006Posts: 320Location: Cali, C olombia

Posted: Thu Dec 18, 2008 3:22 Post subject:

thanks for this. i will give it a try tomorrow and see what happens.

__________ _______WRT54GS v2.1 > v24-sp2 (01/01/09) megaWRT54GS v5 > v24-sp2 (01/01/09) microPPTP, WDS link and SD Mod

Back to top

Goto page 1, 2, 3, 4 Next Dis pla y p os ts f rom prev ious : A ll P os ts O ld es t F ir st Go Page 1 of4

DD-WRT Forum Forum Index -> Broadcom SoC based HardwareAll times are GMT

Navigation

Jump to: Broadcom SoC based Hardware Go

You cannot post new topics in this forumYou cannot reply to topics in this forum

You cannot edit your posts in this forumYou cannot delete your posts in this forum

You cannot vote in polls in this forumYou can attach files in this forum

You can download files in this forum

Powered by phpBB 2001, 2005 phpBB Group 2008 NewMedia-NET GmbH

t d b W b2PDFC t
http://www.web2pdfconvert.com/?ref=PDFhttp://www.web2pdfconvert.com/?ref=PDFhttp://www.phpbb.com/http://dd-wrt.com/phpBB2/viewforum.php?f=1&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/index.php?sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=reply&t=40464&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=newtopic_wtf&f=1&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=15&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=45&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=30&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?t=40464&postdays=0&postorder=asc&start=15&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/privmsg.php?mode=post&u=10142&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/profile_sec.php?mode=viewprofile&u=10142&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/posting_sec.php?mode=quote&p=241109&sid=a9ffc1773346466c6d1032f3f2a649d9http://dd-wrt.com/phpBB2/viewtopic.php?p=241109&sid=a9ffc1773346466c6d1032f3f2a649d9#241109

Documents

Dd-wrt Modificacion de Memoria MMC