Daniel Senior Orifice Fitting Tech Guide

8/12/2019 Daniel Senior Orifice Fitting Tech Guide

http://slidepdf.com/reader/full/daniel-senior-orifice-fitting-tech-guide 1/36

Technical Guide

May 2013

Daniel™ Senior™ Orifice FittingDifferential Pressure Flow Meters





1www.EmersonProcess.com

Technical GuideDifferential Pressure Flow Meters

Overview

The Daniel Senior Orifice Fitting is a dual-chamber device thatreigns as the most widely used means of measurement for

natural gas. With an installed base of well over one million

orifice fittings worldwide, more natural gas is measured with

The Daniel Senior Orifice Fitting than any other type of device.

The Senior Orifice Fitting (Figure 1) saves users time and

money by providing a fast, safe and extremely simple

method of changing orifice plates under pressure without

flow interruption, preventing unscheduled shutdowns. In

addition, its dual-chamber design eliminates the need for costly

piping bypasses or additional valves and fittings required with

conventional orifice flange installations.

The Senior Orifice Fitting meets all requirements and

recommendations for accurate flow measurement of gas

and liquid, including AGA-3 / API 14.3 requirements, without

compromise.

From duplex stainless steel fittings to carbon steel and severe

service trims (Monel, Hastellloy-C and Alloy-20), Daniel delivers

fittings to meet the stringent requirements of corrosive

environments or specific temperature and pressure needs.

The Senior Orifice Fitting requires no beta ratio range

restrictions and no added uncertainty to published values. It

is available in 2" through 48" flange line sizes, up to ANSI 2500,

and 10,000 psi (68958 kPa) in 3" to 6" only.

Proving its worth every day

(1) Please consult Daniel factory for severe service and other code requirements, including low -temp, high H2S, high CO

2, and special applications.

(2) Hard-seat using injected grease / sealant is recommended for production applications where sand, gri t and other particulate matter is present.

(3) Soft-seat, greaseless seal is not recommended / intended for production applications where s and, grit and other particulate matter is commonly present (e.g.,shale gas production).

Typical Applications

Gas transmission / pipeline

Gas distribution

Offshore gas production and onshore, including shale

Gas plants

Floating Production, Storage and Off loading (FPSO)

CO2 injection

Bi-directional high pressure storage

Features and Benefits

Highly reliable, time proven technology

Field-repairable, reducing downtime and costsassociated with shipping to a repair site

Available in compliance with ISO-5167, PED, NORSOK

and other code standards / requirements (1)

Corrosion resistant and other special casting materials,

including Wrought Carbon Steel (WCC, WCB), Low

Temperature Carbon Steel (LCC), 316 Stainless Steel

and Duplex, makes this fitting suitable for sour gas

service and other special applications

Slide valve / isolation mechanism featuring a metal-to-

metal seat (hard seat(2)) with injected lubricant /sealant is standard on all Daniel Senior Orifice

Fittings, providing an optimal seal in the production

environment where particulate matter is common

Optional soft seat slide valve(3) (O-ring seal without

lubricant) is available in 2" to 12" sizes, up to 600 ANSI,

for use with gas products such as ethylene

Figure 1: Daniel Senior Orifice Fitting



2 www.EmersonProcess.com

May 2013Senior Orifice Fitting

A. Under flow conditions B. Equalize pressure 1. Open equalizer valve

Operational Sequence of Removing an Orifice PlateUnder Pressure(1)

D. Bleed upper chamber and lubricate valve seat 4. Close slide valve carrier (isolation mechanism) 5. Close equalizer valve and inject sealant 6. Open bleeder valve (blow-down valve)

C. Raise orifice plate 2. Open slide valve carrier (isolation mechanism) 3. Raise plate to upper chamber

(1) CAUTION: This operational sequence is representational only and is not intended for use as a field guide to operations. NOTICE : See operation manual andalways read and follow the detailed operating instructions provided with each fi tting before attempting to operate.





The slide valve seat and the slide valve strip are eld-replaceableor repairable (re-lapping) without removing the tting from theline, reducing downtime.

E. Remove orifice plate7. Remove clamping bar, sealing bar, and gasket 8. Remove orice plate from top chamber

Stop Pin

Valve Seat Gasket

Slide Valve Seat

Slide Valve Strip

Slide Valve Springs

Slide Valve Carrier

Operating shaftand Pinion

Senior Orifice Fitting Front View

Valve Seat

Sealing Surface

Top Chamber





Standard Specifications(1)

(1) Please consult Daniel if your requirements are outside the specifications. Other product and material offerings may be available depending on the application.

(2) Orifice Plate Seal used may limit the service temperatures and special trims w ill be required for high temperature applications. Maximum temperature iscontingent on limited pressure. Please consult fac tory.

Indicator Plates

Standard on all Senior Orifice Fittings, the indicator plate clearlyshows the direction of the open and closed position of the slide

valve.

Operating Wrench

An operating wrench is provided with each fitting for safe

operation of the shaft and pinions, equalizer valve, grease gun,

bleeder valve and clamping bar screws.

Hydrostatic Testing

All Daniel Senior Orifice Fittings are hydrostatically tested to 1.5

times operating pressure.

Trim

NACE Trim (MR-0175-2002) 2" to 8" 150 to 600 ANSI

RFFN Fit tings (Standard)

A-trim 10" + and all ANSI classes 900+ (Standard)

Other optional trims available for severe service

and other code requirements (High H2S, High CO

2,

NORSOK, Daniel “AASG” and special applications)

Senior Orifice Fitting - FlangnekTM

ConfigurationSenior Orifice Fitting - Flanged Configuration

Differential Pressure Taps

Internal Tap Hole Sizes

In accordance with API 14.3 (AGA Report #3)

In accordance with ISO-5167 (option)

1/2" NPT Process Connection (Standard)

In accordance with API 14.3 (standard for all)

Flanged differential taps (option)

Telemetering Taps

Standard on all 2 to 12 inch 600 ANSI

Available on all other sizes and ANSI classes

Line Bore Tolerances 2" and 3" sizes, ± .003"

4", 6", 8", 10" sizes, ± .004"

12" and 16", ± .005"

Operating Shafts

Stainless Steel, double-ended (standard)

▪ Eliminates the need to reverse shafts in the field

Application Temperature

Maximum Temperatures(2)

150 to 900 ANSI, -20°F to +450°F(2) (-29°C to 232°C)

1500 and 2500 ANSI, -20°F to +275°F (2) (-29°C to 135°C)





(1) NOTE: Body / Top Gasket peroxide-cured Nitrile O-ring for ANSI 1500 Orifice Fit tings. Male and female gasket joint with ParkerTM

seal gaskets for ANSI 2500 OrificeFitting.

Figure 2 shows the extra-heavy construction of the wall

sections and essential parts on the ANSI 1500 Senior Orifice

Fitting.

All seal ring units for use in 900 to 2500 ANSI fittings are

required to be Snap Seal or PTFE Seal Rings.

Thin section on internal edgefor flexible lip seal, yielding

easily to pressure

Heavy weight section on externaledge to prevent compression drift

between joints

Force exerted on

surface tending to

change its shape will

not affect gasket seal

Constant pressure seals

gasket at all times

Alloy steel studs

Corrosion resistant slide valve seat

Heavy wall sections

Oversized stuffing box units

Double row clamping bar screws(constraining force directly over

gasket)

Robust Carbon Steel

clamping and sealing

bars

Figure 2: Partial Side Sectional ElevationDaniel ANSI 1500 and 2500(1) Fittings

Special Features

36 inch ANSI 600 Senior Orifice Fitting

High Pressure Fittings

Daniel Sealing Bar Gasket





Meter Tube Flange Fitting Flange

Daniel 400 and Higher ANSIDaniel 125 to 300 ANSI

Figure 3: Method of Aligning Meter Tube Flange to OrificeFitting Flange

(1) CAUTION: This view is representational only and is not intended for use as a field guide to operations. NOTICE : See operation manual and always read andfollow the detailed operating instructions pr ovided with each fitting before attempting to operate.

(2) Slide valve / Isolation mechanism does not comply with or adhere to API 598 valve criteria. Hard seat (using sealant / lubricant) is s tandard on all Daniel Senior OrificeFittings.Soft seat (O-ring seal using no grease) is available in size 2" to 12" up to 600 ANSI. Not intended for production applications.

In Daniel Senior Orifice Fittings, the slide valve seat (Part No. 18)

is part of the upper chamber. The slide valve strip (Part No.3)

moves underneath this seat, thereby utilizing line pressure to

affect a positive seal. The slide valve strip is maintained in the

“floating” position by minimum spring pressure.

Before the slide valve (Figure 4) is opened, sealant (lubricant)

is injected using the grease gun (Part No. 23). Pressure is

Top Chamber

Continuous Grease Groove (Encircle Valve Opening)

Equalizer Valve (part No. 1)

Equalizer Passageways

Slide Valve Strip (Part No. 3)

Lower CompartmentClearance pad prevents slide valve

from being closed until plate

carrier is fully centered in the line.

Slide Valve Carrier (Part No. 17)

Slide Valve Seat (Part No. 18)

Grease Gun (Part No. 23)

Figure 4: Slide Valve / Isolation Mechanism(2)

Alignment of Meter Tube Flange to Orifice Fitting Flange

On all sizes, 300 ANSI or under, three dowel pin flange-

alignment holes are drilled in the flanges.

On Daniel 400 ANSI fittings or higher, flanges aremanufactured with close-tolerance, square-shouldered, large

male flange-facing on fitting, and large female flange-facing

on meter tube to assure proper internal alignment.

Flange gaskets are precision-cut so they will not, under

compression, extend into the internal bore of fitting. Refer to

Figure 3.

Slide Valve(1)

then equalized throughout the entire fitting by operation of

the equalizer valve (Part No. 1). Equalized pressure on both

sides of the slide valve strip allows slide valve to move freely

without wear. The metal-to-metal hard seat seal (with injected

sealant / lubricant) provides an optimal and reliable seal in the

production environment where sand and particulate matter are

common.





Plate Alignment

The plate carriers in all 2" to 8" Senior Orifice Fittings are

centered using a fixed three-point positioning system. This

assures orifice plate concentricity in accordance with current API

14.3 (AGA Report #3) tolerances while the fitting is positionedin the vertical and horizontal planes.

The Senior Orifice Fitting is composed of two independent

compartments separated by a hardened stainless steel slide

valve.

The side sectional view, Figure 5, demonstrates the slide valve

in theclosed position and orifice plate concentric in line of

flow. The slide valve cannot be closed unless the orifice plate

is concentric to the bore of the fitting or in the upper chamber

during plate removal.

Figure 6 demonstrates the Daniel top chamber in the opened

position with the plate carrier in place for change or inspection

of the orifice plate. Only a few turns of the operating wrench

are required to loosen screws to remove or replace clamping

and sealing bars. Set screws always remain in the clamping bar.

This feature adds greatly to speed and ease of operation.

The plate carrier is raised and lowered by a double rack and

pinion mechanism with power applied through an operating

wrench. This method provides the safest means of operation

with the least amount of effort and assures positive control of

the plate carrier at all times(1).

All parts, including the essential slide valve assembly, may bereplaced or repaired without removing the fitting from the line.

Orifice Plate Sealing UnitsDesigned by Daniel, the plate sealing units provide a secure

seal between orifice plate and body seats and can be used for a

variety of services.

Plate Carrier

The plate carrier protects orifice plate at all times while

inserting or removing from the fitting and can be easily inserted

while fitting is rolled in the horizontal position.

Indicator Plate

The indicator plate clearly shows the position of the slide valve

within the fitting.

PTFE Shaft Packing and Centering Rings

The PTFE shaft packing and centering rings are standard

equipment on all Daniel Senior Orifice Fittings in all sizes and

ratings.

Compact DesignThe compact design of the Senior Orifice Fitting requires

minimum operating space.

Fittings

Daniel Senior Orifice Fittings up to and including 12" line size

can operate in a vertical down flow condition or positioned in

horizontal flow for side opening.

All fittings are designed and manufactured to meet API / AGA

recommendations, and in strict accordance with A.S.T.M.

specifications. For other code requirements and special

applications, including NORSOK, ISO, PED, CO2, H2S, lowtemperature, please consult factory.

The Senior Orifice Fitting Advantage

(1) CAUTION: This is not intended for use as a f ield guide to operations. NOTICE : See operation manual and always read and follow the detailed operatinginstructions provided with each f itting before attempting to operate.

Figure 5: Side SectionalView of Daniel SeniorOrifice Fitting

Figure 6: Daniel SeniorOrifice Fitting - TopChamber Open





Orifice Plate Sealing UnitsOrifice plates manufactured by Daniel are quality-controlled from the selection of raw materials to packaging of finished products.

The orifice plate sealing unit provides a seal between orifice plate and body seats and it is available for a variety of services.

Dual Seal (DSC)The Dual Seal (DSC) is the most simple and practical orifice

plate sealing device for normal flowing streams. It is precision

molded from 70-80 shore nitrile synthetic rubber(1) and

provides four rubber-to-metal sealing surfaces 360° around

the plate. The units securely seal against both outer faces of

the plate and against both seats of the orifice fitting to prevent

leakage.

In 16" sizes and up, DS seal rings are not available. The Dual

Vulcanized Seal (DVS) is bonded from 80-90 shore rubber

directly to the outer edge of the orifice plate at the factory.

If damaged, the DVS seal and plate may be returned to the

factory for revulcanizing. The DSC and DVS seals are used in

Daniel fittings sizes up to ANSI 600, in temperatures from -20°F

to +275°F.

Snap Seal Ring (SSR)The Snap Seal Ring (SSR) unit is a removable orifice plate holder

designed for use where elastomer seal swelling is a problem.

Certain media, such as ethylene or carbon dioxide may cause

seal swelling when other types of seal units are removed from

high-pressure service.

The Snap Seal Ring unit consists of two symmetrical metal

rings, each one having an O-ring on both sides for a secure

seal on the plate side and the fitting side of the ring. The

orifice plate is centered and secured between these rings. The

assembled unit provides a full 360° rubber-to-metal seal around

both sides even in the absence of pressure differential.

No special tools are required for assembly or disassembly.

When ordering, please specify nominal line size, schedule, plate

thickness, and flowing media or material choice.

Snap Seal Ring (SSRC) in 2" to 8", (SSR) in 10" to 24"

Materials

316 stainless steel

Zinc-plated carbon steel

Duplex and Inconel available

Operating Temperature

-20°F to +275°F (standard O-rings) -67°F to +437°F (FKM Fluoroelastomer O-rings)(2)

Available Sizes

2" to 24"

ANSI

900, 1500 and 2500

Dual Seal (DSC) in 2" to 8", (DS) in 10" to 12"

Materials

2" to 10": 70-80 shore nitrile synthetic rubber(1)

12" and up: 80 -90 shore rubber


-20°F to +275°F

Available Sizes 2" to 12"

ANSI

Up to 600

(1) Also available in FKM Fluoroelastomor.

(2) FKM is the designation for a class of fluoroelastomers as defined in ASTM D1418 and ISO 1629.





PTFE Seal (TSC)

The PTFE Seal (TSC) is a superior orifice plate seal unit for

difficult, corrosive flows and for higher temperatures than the

Dual Seal (DSC) unit can handle. The TSC has proven effective in

flows such as dilute sulphuric acid, fuming nitric acid, hydrazine,liquid oxygen and other unusual flows, from -65°F to +500°F(1).

The two-piece unit consists of an inlet ring which fits around the

plate outer diameter, and a downstream ring fitted with metal

clips for assembling the orifice plate sealing unit. A unique

and an annular groove(2) on the ring provides compression to

effectively seal off the plate.

The TSC unit can be assembled or taken apart by hand and is

interchangeable in 2" to 10" sizes with Daniel Dual (DSC) and

Metal (MSC) Seal units. The TSC is recommended with Daniel

900, 1500 and 2500 ANSI fittings or lower pressure where

rubber seals may not be satisfactory.

Metal Seal (MSC)(3)

The Metal Seal (MSC) is a stainless or zinc-plated carbon steel

clip-ring assembly recommended for high pressures and for

temperatures up to 1200°F(4). The assembly consists of an

upstream and a downstream ring. The upstream ring has arecessed groove into which a thin leaf-spring is inserted. A seal

is created by clamping the plate between the rings, thereby

providing the necessary compression to seat the plate against

the downstream ring.

Metal Seal units of zinc-plated carbon steel are recommended

for services to +600°F(4), standard 316 stainless steel units to

+1000°F(4), and 316 stainless steel units with an inconel spring

to +1200°F(4).

The Metal Seal unit can be assembled or taken apart by hand

and is interchangeable in 2" to 12" sizes with Dual Seal (DSC) and

PTFE Seal (TSC) units.

PTFE Seal (TSC) in 2" to 8", (TS) in 10" to 24"

Materials

PTFE Seal (900, 1500 and 2500)


-65°F to +500°F

Available Sizes

2" to 10"

ANSI

900, 1500 and 2500

Metal Seal (MSC) in 2" to 8", (MS) in 10" to 24"

Materials

316 stainless steel seal (standard)

Zinc-plated carbon steel seal

Operating Temperature(1)

450°F (316 stainless steel) standard

450°F (316 stainless steel) with an inconel spring

450°F (zinc-plated carbon steel)

Available Sizes

2" to 24"

ANSI

900, 1500 and 2500

(1) For higher temperatures, please consult factory.

(2) This groove should be spread by inserting a tool such as a screw dri ver and rotating 360° to re-engage the spring lip after each use. NOTICE : See operation manualand always read and follow the detailed operating instructions provided with each f itting before attempting to operate.

(3) Not intended for custody transfer accuracy applications.

(4) Application temperatures above 450°F are intended for single chamber devices and require factory consultation.





Daniel’s new plate carrier reduces measurement uncertainty

using a three-point positioning system. This assures

concentricity within the fitting in accordance with the API

14.3 (A.G.A. Report #3) and ISO-5167 standards. Metal-

to-metal contact of the plate outer diameter with the

inner diameter of the plate carrier, coupled with precision

contact points of the plate carrier to the fitting affords

users consistent compliance with AGA eccentricity

requirements in vertical or horizontal plane.

Design Features

1. Precision ground corner tabs keep the orifice

plate carrier in the proper position and allow the

fitting to be mounted in the nine, twelve, orthree o’clock position. (See Figure 7)

2. Notched seal ring design provides metal-

to-metal contact for reliable alignment and

centering of the orifice plate

3. The fitting’s pin and the spring loaded

button located at the top of the orifice plate

carrier ensure tight positioning of the plate

carrier when the slide valve is closed and

the Senior Orifice Fitting is in the vertical or

horizontal metering position

4. Wide flow ports reduce differential pressure

load across the plate surface

5. A 360° seal ring support shelf secures the plate

in place

Orifice Plate Carrier

The new plate carrier is compatible with Daniel Senior Orifice

Fittings manufactured after 1991. To upgrade the plate carrier

of your Senior Orifice Fitting, please contact your local Daniel

representative.

3

5

2

4

1

31

Figure 7: Mounting Options Available

Nine O’Clock (Far side)

Twelve O’Clock Three O’Clock (Near side)

Vertical Down





Daniel Lubricant

TEMPERATURE (F°)

1,300 PSIG

200 PSIG

1,400 PSIG

130 PSIG

0°-20° 40° 60° 80° 100° 120° 140° 160°20°

PRESSURE

(0-1400 PSIG)

Type 1

TEMPERATURE (F°) 0°-20° 40° 60° 80° 100° 120° 140° 160°20°

PRESSURE

(0-1400 PSIG)

Type 21,350 PSIG

135 PSIG

65 PSIG

115 PSIG

TEMPERATURE (F°) 0°-20° 40° 60° 80° 100° 120° 140° 160°20°

PRESSURE

(0-1400 PSIG)

Type 3 1,100 PSIG 1,000 PSIG

750 PSIG

200PSIG

1,400 PSIG

50 PSIG 75 PSIG

450 PSIG

TEMPERATURE (F°) 0°-20° 40° 60° 80° 100° 120° 140° 160°20°

PRESSURE

(0-1400 PSIG)

Type 4 1100 PSIG

200 PSIG

1,400 PSIG

90 PSIG120 PSIG

Lubricant Optimum Sealing Zones

Lubricant Stick

Daniel lubricant is specifically designed for lubricating the slide

valve(1) of Senior Orifice Fittings, ensuring maximum operating

performance. Because it is a chemical compound rather than

a petroleum based product, this lubricant has significant

advantages:

• Effective over a wide range of demanding temperatures

(-40° to +500°F) and pressures (0 to 1,400 psig)

• Contains no fillers or inert materials, eliminating hardening

or oxidizing

• Reduces friction and wear, extending equipment life in

severe conditions

• Insoluble in water and extremely resistant to hydrocarbons

within its temperature range

• Different types of lubricants are available to meet the various

demanding needs of gas applications

Daniel lubricant is available in B-sized sticks (3/8" diameter, 1.5"

long) in 24-stick boxes. The cylinder shape (grease stick) fits

neatly into the fitting’s grease gun (Figure 8).

Note

Hard seat (using sealant / grease sticks) is standard on all Daniel

Senior Orifice Fittings, providing an optimal seal in the production

environment where fractionation sand and other particulate matter

are common.

Soft seat (O-ring seal using no grease) is available in size 2" to 12" up

to 600 ANSI for use with gas products such as ethylene.

Figure 8: Grease Gun

Stem

ThreadedSection Plunger

Threaded Section of Grease GunBody Fastened into Senior Fitting Top

Grease Gun Body

Internal Fluid PressureContained in the Fitting

Grease Receiver-Body

One-Way Check Valve Ball

(1) Daniel slide valve / isolation mechanism does not comply with or adhere to API 598 valve criteria and does not guarantee zero leak seal.





F l a n g n e k ™ -

R a i s e d F

a c e ( 1

) 2 " t o 1 6 " 1 5 0 t o 9 0 0

A N S I

( 1 ) D o u b l e - e n d e d o p e r a t i n g s h a f t s a r e s t a n d a

r d .








R i n g J o i n t ( 1 ) 2 " t o 1 6 " 6 0 0 A N S I a n d 2 " t o 1 6 " 9 0 0 A N S I


r d .





Standard Trim(2)

A.P.I. Ring Number

Diameter Internal Line Bore

Upstream Face of Orifice Plate to Face

of End

Downstream Face of Orifice Plate to

Face of End

Overall Face to Face

Operating Clearance from Center

Body Clearance from Center

Clearance to Bottom

Centerline to Top

Clearance for Plate Changing

Diameter of Flange

Diameter of Bolt Circle

Pitch Diameter of Ring and Groove

Depth of Groove

Width of Groove

Flange Thickness

Number of Bolts / Studs per Flange

Diameter of Bolts / Studs per Flange

Length of Bolts / Studs with 2 Hex Nuts

Diameter of Hub at Point of Welding

Size of Drain Plugs(1)

Orifice Plate Thickness

Weight (lb)

Minimum Clearance for Clamping Bar

Removal

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L 2

M 1

M 2

N

1

O

P

R

W

C a t a l o g N o . 0

1 4 5 - D a n i e l 2 - 1 6 " F l a n g n e k - R i n g J o i n t 6 0 0 A N S I

N A C E

2 " R - 2 3

*

5 5 / 1 6

5 5 / 1 6

1 0 3 / 4

1 3

7

4

1 4

6

6 1 / 2

5

3 1 / 4

5 / 1 6

1 5 / 3 2

1

8

5 / 8

4 1 / 2

2 . 3

7 5

1 / 2

1 / 8

1 0 5

9

N A C E

3 " R - 3 1

*

7

7

1 4 1 / 8

1 4

8

5

1 5

7

8 1 / 4

6 5 / 8

4 7 / 8

5 / 1 6

1 5 / 3 2

1

1 / 4

8

3 / 4

5 1 / 4

3 . 5

0 0

1 / 2

1 / 8

1 6 0

1 1

N A C E

4 " R - 3 7

*

6 5 / 8

6 5 / 8

1 3 3 / 8

1 5

9

6

1 6

8

1 0 3 / 4

8 1 / 2

5 7 / 8

5 / 1 6

1 5 / 3 2

1

1 / 2

8

7 / 8

6

4 . 5

0 0

3 / 4

1 / 8

2 6 5

1 3

N A C E

6 " R - 4 5

*

8

8

1 6 1 / 8

1 6

1 0

7

1 9

1 0

1 4

1 1 1 / 2

8 5 / 1 6

5 / 1 6

1 5 / 3 2

1

7 / 8

1 2

1

7

6 . 6

2 5

3 / 4

1 / 8

4 0 0

1 6

N A C E

8 " R - 4 9

*

8 1 1 / 1 6

8 1 1 / 1 6

1 7 5 / 8

1 7

1 1

9

2 2

1 2

1 6 1 / 2

1 3 3 / 4

1 0 5 / 8

5 / 1 6

1 5 / 3 2

2

3 / 1 6

1 2

1 1 / 8

8

8 . 6

2 5

3 / 4

1 / 4

5 9 5

1 9

A

1 0 " R - 5 3

*

9 1 / 1 6

8 1 / 1 6

1 7 3 / 8

1 8

1 2

1 0

2 5

1 4

2 0

1 7

1 2 3 / 4

5 / 1 6

1 5 / 3 2

2

1 / 2

1 6

1 1 / 4

8 3 / 4

1 0 . 7

5 0

3 / 4

1 / 4

7 4 5

2 2

A

1 2 " R - 5 9

*

9 7 / 8

8 7 / 8

1 9

2 0

1 4

1 1

2 8

1 6

2 2

1 9 1 / 4

1 5

5 / 1 6

1 5 / 3 2

2

5 / 8

1 2

1 1 / 4

9

1 2 . 7

5 0

3 / 4

1 / 4

1 , 2

1 5

2 6

A

1 4 " R - 6 1

*

1 0 5 / 1 6

1 0 5 / 1 6

2 0 7 / 8

2 1

1 5

1 2

3 2

1 8

2 3 3 / 4

2 0 3 / 4

1 6 1 / 2

5 / 1 6

1 5 / 3 2

2

3 / 4

2 0

1 3 / 8

9 3 / 4 1 4 . 0

0 0

3 / 4

1 / 4

1 , 4

7 5

2 9

A

1 6 " R - 6 5

*

1 0 1 1 / 1 6 1

0 1 1 / 1 6

2 1 3 / 4

2 4

1 8

1 4

3 6

2 0

2 7

2 3 3 / 4

1 8 1 / 2

5 / 1 6

1 5 / 3 2

3

2 0

1 1 / 2

1 0 1 / 2 1 6 . 0

0 0

3 / 4

3 / 8

2 , 3

1 5

3 6


1 4 6 - D a n i e l 2 - 1 6 " F l a n g n e k - R i n g J o i n t 9 0 0 A N S I ( u s e P T F E S e a l

R i n g o r S S R o n l y )

A

2 " R - 2 4

*

7

7

1 4 1 / 8

1 3

7

5

1 4

6

8 1 / 2

6 1 / 2

3 3 / 4

5 / 1 6

1 5 / 3 2

1

1 / 2

8

7 / 8

6

2 . 3

7 5

1 / 2

1 / 8

2 0 5

1 1

A

3 " R - 3 1

*

7

7

1 4 1 / 8

1 4

8

5

1 5

7

9 1 / 2

7 1 / 2

4 7 / 8

5 / 1 6

1 5 / 3 2

1

1 / 2

8

7 / 8

6

3 . 5

0 0

1 / 2

1 / 8

2 1 5

1 1

A

4 " R - 3 7

*

7 7 / 8

7 1 / 8

1 5 1 / 8

1 5

9

6

1 6

8

1 1 1 / 2

9 1 / 4

5 7 / 8

5 / 1 6

1 5 / 3 2

1

3 / 4

8

1 1 / 8

7

4 . 5

0 0

3 / 4

1 / 8

3 0 0

1 3

A

6 " R - 4 5

*

8 5 / 8

8

1 6 3 / 4

1 6

1 0

8

1 9

1 0

1 5

1 2 1 / 2

8 5 / 1 6

5 / 1 6

1 5 / 3 2

2

3 / 1 6

1 2

1 1 / 8

8

6 . 6

2 5

3 / 4

1 / 8

4 9 0

1 6

A

8 " R - 4 9

*

9 1 / 8

9 1 / 8

1 8 1 / 2

1 7

1 1

1 0

2 2

1 2

1 8 1 / 2

1 5 1 / 2

1 0 5 / 8

5 / 1 6

1 5 / 3 2

2

1 / 2

1 2

1 3 / 8

9

8 . 6

2 5

3 / 4

1 / 4

1 , 0

9 5

2 0

A

1 0 " R - 5 3

*

1 0 7 / 8

1 0 7 / 8

2 2

1 9

1 3

1 1

2 5

1 4

2 1 1 / 2

1 8 1 / 2

1 2 3 / 4

5 / 1 6

1 5 / 3 2

2

3 / 4

1 6

1 3 / 8

9 1 / 2

1 0 . 7

5 0

3 / 4

1 / 4

1 , 5

5 5

2 6

A

1 2 " R - 5 7

*

1 1 5 / 8

1 1 5 / 8

2 3 1 / 2

2 1

1 5

1 2

2 8

1 6

2 4

2 1

1 5

5 / 1 6

1 5 / 3 2

3

1 / 8

2 0

1 3 / 8

1 0 1 / 4

1 2 . 7

5 0

3 / 4

1 / 4

1 , 9

3 5

2 8

A

1 4 " R - 6 2

*

1 1 1 / 1 6

1 1 1 / 4

2 2 9 / 1 6

2 2

1 6

1 3

3 2

1 8

2 5 1 / 4

2 2

1 6 1 / 2

7 / 1 6

2 1 / 3 2

3

3 / 8

2 0

1 1 / 2

1 0 1 / 2

1 4 . 0

0 0

3 / 4

1 / 4

2 , 1

1 5

2 9

A

1 6 " R - 6 6

*

9 1 3 / 1 6 1

2 1 3 / 1 6

2 3

2 6

2 0

1 4

3 6

2 0

2 7 3 / 4

2 4 1 / 4

1 8 1 / 2

3 9 / 8 9

2 1 / 3 2

3

1 / 2

2 0

1 3 / 4

1 1

1 6 . 3

1 5

3 / 4

3 / 8

C F

3 6

( 1 ) F l a n g e d p r o c e s s c o n n e c t i o n s a v a i l a b

l e .

( 2 ) P l e a s e c o n s u l t D a n i e l f a c t o r y o r r e p r e s e n t a t i v e f o r o t h e r t r i m s a v a i l a b l e f o r s e v e r e s e r v

i c e a n d o t h e r c o d e r e q u i r e m e n t s ,

i n c l u d i n g l o w - t e m p e r a t u r e ,

h i g h H

2 S ,

H i g h C O

2 ,

N O R S O K ,

I S O 5 1 6

7 ,

P E D ,

D a n i e l

“ A A S G ” , a n d s p e c i a l a p p l i c a t i o n s .






R a i s e d F

a c e

( 1 ) 2 " t o 1 6 " 1 5 0 0 A N S I

a n d 2 " t o 1 2 " 2 5 0 0 A N S I


r d .





Standard Trim(2)



of End

Downstream Face of Orifice Plate toFace of End




Clearance to Bottom

Centerline to Top


Diameter of Flange


Diameter of Raised Face +.000 -.005

Height of Raised Face

Flange Thickness


Diameter of Bolts / Studs per Flange





Weight (lb)


Removal

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L

M

N

O

P

R

W


1 7 - D a n i e l 2 - 1 6 " F l a

n g n e k - R a i s e d F a c e 1 5 0 0 A N S I ( u s e P T F E S e a l R i n g o r S S R o n l y )

A

2 "

*

6 1 5 / 1 6

6 1 5 /

1 6

1 4

1 3

7

5

1 4

6

8 1 / 2

6 1 / 2

3 . 6

2 5

1 / 4

1 1 / 2

8

7 / 8

5 3 / 4

2 . 3

7 5

3 / 4

1 / 8

2 0 5

1 1

A

3 "

*

8 3 / 1 6

7 1 1 /

1 6

1 6

1 4

8

6

1 5

7

1 0 1 / 2

8

5 . 0

0 0

1 / 4

1 7 / 8

8

1 1 / 4

7

3 . 5

0 0

3 / 4

1 / 8

2 7 5

1 3

A

4 "

*

8 3 / 8

7 7

/ 8

1 6 3 / 8

1 6

1 0

7

1 7

8

1 2 1 / 4

9 1 / 2

6 . 1

8 8

1 / 4

2 1 / 8

8

1 1 / 4

7 3 / 4

4 . 5

0 0

3 / 4

1 / 8

4 4 5

1 6

A

6 "

*

1 0 3 / 4

1 0 3 /

1 6

2 1 1 / 1 6

1 6

1 0

8

2 0

1 0

1 5 1 / 2

1 2 1 / 2

8 . 5

0 0

1 / 4

3 1 / 4

1 2

1 3 / 8

1 0 1 / 4

6 . 6

2 5

3 / 4

1 / 8

7 1 0

2 0

A

8 "

*

1 1 2 3 / 3 2

1 1 5 / 3 2

2 3 1 / 8

1 8

1 2

1 0

2 3

1 2

1 9

1 5 1 / 2

1 0 . 6

2 5

1 / 4

3 5 / 8

1 2

1 5 / 8

1 1 1 / 2

8 . 6

2 5

3 / 4

1 / 4

1 2 4 0

2 2

A

1 0 "

*

1 2 5 / 1 6

1 2 5 /

1 6

2 4 1 / 2

1 9

1 3

1 2

2 6

1 4

2 3

1 9

1 2 . 7

5 0

1 / 4

4 1 / 4

1 2

1 7 / 8

1 3 1 / 4

1 0 . 7

5 0

3 / 4

1 / 4

1 7 4 5

2 6

A

1 2 "

*

1 3 5 / 1 6

1 3 5 /

1 6

2 6 7 / 8

2 3

1 7

1 4

2 9

1 6

2 6 1 / 2

2 2 1 / 2

1 5 . 0

0 0

1 / 4

4 7 / 8

1 6

2

1 4 3 / 4

1 2 . 7

5 0

3 / 4

1 / 4

2 , 8

0 5

3 0

A

1 4 "

*

1 0 1 5 / 1 6

1 5 1 3 /

1 6

2 7 1 / 8

2 7

2 1

1 7

3 5

1 8

2 9 1 / 2

2 5

1 6 . 2

5 0

1 / 4

5 1 / 4

1 6

2 1 / 4

1 6

1 4 . 3

1 5

3 / 4

1 / 4

C F

3 1

A

1 6 "

*

1 1 1 5 / 1 6

1 6 1 1 /

1 6

2 9

2 8

2 2

1 7

3 6

2 0

3 2 1 / 2

2 7 3 / 4

1 8 . 4

9 7

1 / 4

5 3 / 4

1 6

2 1 / 2

1 7 1 / 2

1 6 . 3

1 5

3 / 4

3 / 8

C F

3 6


1 8 - D a n i e l 2 - 1 2 " F l a

n g n e k - R a i s e d F a c e 2 5 0 0 A N S I ( u s e P T F E S e

a l R i n g o r S S R o n l y )

A

2 "

*

8 5 / 8

8 5

/ 8

1 7 3 / 8

1 6

1 0

6

1 7

8

9 1 / 4

6 3 / 4

3 . 6

2 5

1 / 4

2

8

1

7

2 . 3

7 5

1 / 2

1 / 8

5 2 0

1 3

A

3 "

*

9 9 / 1 6

9 9 /

1 6

1 9 1 / 4

1 6

1 0

6

1 7

8

1 2

9

5 . 0

0 0

1 / 4

2 5 / 8

8

1 1 / 4

8 3 / 4

3 . 5

0 0

1 / 2

1 / 8

5 7 5

1 3

A

4 "

*

1 0 1 / 2

1 0 1

/ 2

2 1 1 / 8

1 7

1 1

7

1 7

8

1 4

1 0 3 / 4

6 . 1

8 8

1 / 4

3

8

1 1 / 2

1 0

4 . 5

0 0

3 / 4

1 / 8

7 1 5

1 5

A

6 "

*

1 2 1 / 2

1 2 1

/ 2

2 5 1 / 8

1 8

1 2

1 0

2 0

1 0

1 9

1 4 1 / 2

8 . 5

0 0

1 / 4

4 1 / 4

8

2

1 3 3 / 4

6 . 6

2 5

3 / 4

1 / 8

1 , 1

9 5

2 0

A

8 "

*

1 9 9 / 1 6

1 9 9 /

1 6

3 9 3 / 8

2 6

2 0

1 1

3 9

2 0

2 1 3 / 4

1 7 1 / 4

1 0 . 6

2 5

1 / 4

5

1 2

2

1 5

8 . 6

2 5 3

/ 4

1 / 4

1 6

A

1 0 "

*

2 2 5 / 8

2 2 5

/ 8

4 5 1 / 2

2 7

2 1

1 4

4 1

2 1

2 6 1 / 2

2 1 1 / 4

1 2 . 7

5 0

1 / 4

6 1 / 2

1 2

2 1 / 2

1 9 1 / 4

1 0 . 7

5 0 3

/ 4

1 / 4

1 7

A

1 2 "

*

2 3 3 / 8

2 0 7

/ 8

4 4 1 / 2

2 7

2 1

1 5

4 1

2 1

3 0

2 4 3 / 8

1 5 . 0

0 0

1 / 4

7 1 / 4

1 2

2 3 / 4

2 1 1 / 4

1 2 . 7

5 0 3

/ 4

1 / 4

1 7

( 1 ) F l a n g e d p r o c e s s c o n n e c t i o n s a v a i l a b l e .




h i g h H 2 S ,

H i g h C O 2 ,

N O R S O K ,

I S O 5 1

6 7 ,

P E D ,

D a n i e l







R i n g J o i n t ( 1 ) 2 " t o 1 6 " 1 5 0 0 A N S I a n d 2 " t o 1 2 " 2 5 0 0 A N S I


r d .





Standard Trim(2)

A.P.I. Ring Number



of End


Face of End




Clearance to Bottom

Centerline to Top


Diameter of Flange



Depth of Groove

Width of Groove

Flange Thickness


Diameter of Flange Bolts / Studs





Weight (lb)


Removal

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L 2

M 1

M 2

N 1

O

P

R

W


1 4 7 - D a n i e l 2 - 1 6 " F l a n g n e k - R i n g J o i n t 1 5 0 0 A N S I ( u s e T P T F E S e a l R i n g o r S S R o n l y )

A

2 ”

R - 2 4

*

7

7

1 4 1 / 8

1 3

7

5

1 4

6

8 1 / 2

6 1 / 2

3 3 / 4

5 / 1 6

1 5 / 3 2

1 1 / 2

8

7 / 8

6

2 . 3

7 5

1 / 8

1 / 8

2 0 5

1 1

A

3 ”

R - 3 5

*

8 1 / 4

7 3 / 4

1 6 1 / 8

1 4

8

6

1 5

7

1 0 1 / 2

8

5 3 / 8

5 / 1 6

1 5 / 3 2

1 7 / 8

8

1 1 / 8

7 1 / 4

3 . 5

0 0

1 / 2

1 / 8

2 7 5

1 3

A

4 ”

R - 3 9

*

8 7 / 1 6

7 1 5 / 1 6

1 6 1 / 2

1 6

1 0

7

1 7

8

1 2 1 / 4

9 1 / 2

6 3 / 8

5 / 1 6

1 5 / 3 2

2 1 / 8

8

1 1 / 4

8

4 . 5

0 0

3 / 4

1 / 8

4 4 5

1 6

A

6 ” R - 4 6

*

1 0 7 / 8

1 0 5 / 1 6

2 1 5 / 1 6

1 6

1 0

8

2 0

1 0

1 5 1 / 2

1 2 1 / 2

8 5 / 1 6

3 / 8

1 7 / 3 2

3 1 / 4

1 2

1 3 / 8

1 0 1 / 2

6 . 6

2 5

3 / 4

1 / 8

7 1 0

2 0

A

8 ”

R - 5 0

*

1 1 2 9 / 3 2

1 1 1 1 / 3 2

2 3 1 / 2

1 8

1 2

1 0

2 3

1 2

1 9

1 5 1 / 2

1 0 5 / 8

7 / 1 6

2 1 / 3 2

3 5 / 8

1 2

1 5 / 8

1 2

8 . 6

2 5

3 / 4

1 / 4

1 , 2

4 0

2 2

A

1 0 ”

R - 5 4

*

1 2 1 / 2

1 2 1 / 2

2 5 1 / 4

1 9

1 3

1 2

2 6

1 4

2 3

1 9

1 2 3 / 4

7 / 1 6

2 1 / 3 2

4 1 / 4

1 2

1 7 / 8

1 3 3 / 4

1 0 . 7

5 0

3 / 4

1 / 4

1 , 7

4 5

2 6

A

1 2 ”

R - 5 8

*

1 3 5 / 8

1 3 5 / 8

2 7 1 / 2

2 3

1 7

1 4

2 9

1 6

2 6 1 / 2

2 2 1 / 2

1 5

9 / 1 6

2 9 / 3 2

4 7 / 8

1 6

2

1 5 1 / 4

1 2 . 7

5 0

3 / 4

1 / 4 2

, 8 0 5

3 0

A

1 4 ” R - 6 3

*

1 0 1 5 / 1 6

1 5 1 3 / 1 6

2 7 1 / 8

2 7

2 1

1 7

3 5

1 8

2 9 1 / 2

2 5

1 6 1 / 2

5 / 8

1 1 / 1 6

5 1 / 4

1 6

2 3 / 8

1 5 3 / 4

1 4 . 3

1 5

3 / 4

1 / 4

C F

3 1

A

1 6 ”

R - 6 7

*

1 1 1 5 / 1 6

1 7 1 / 8

2 9

7 / 1 6

2 8

2 2

1 7

3 6

2 0

3 2 1 / 2

2 7 3 / 4

1 8 1 / 2

1 1 / 1 6

1 3 / 1 6

5 3 / 4

1 6

2 1 / 2

1 7 1 / 2

1 6 . 3

1 5

3 / 4

3 / 8

C F

3 6


1 4 8 - D a n i e l 2 - 1 2 " F l a n g n e k - R i n g J o i n t 2 5 0 0 A N S I ( 3 ) ( u s e S S R o n l y )

A

2 ”

R - 2 6

*

8 1 1 / 1 6

8 1 1 / 1 6

1 7 1 / 2

1 6

1 0

6

1 7

8

9 1 / 4

6 3 / 4

4

5 / 1 6

1 5 / 1 6

2

8

1

7 1 / 4

2 . 3

7 5

1 / 2

1 / 8

5 2 0

1 3

A

3 ”

R - 3 2

*

9 1 1 / 1 6

9 1 1 / 1 6

1 9 1 / 2

1 6

1 0

6

1 7

8

1 2

9

5

3 / 8

1 7 / 3 2

2 5 / 8

8

1 1 / 4

9

3 . 5

0 0

1 / 2

1 / 8

5 7 5

1 3

A

4 ”

R - 3 8

*

1 0 1 1 / 1 6

1 0 1 1 / 1 6

2 1 1 / 2

1 7

1 1

7

1 7

8

1 4

1 0 3 / 4

6 3 / 1 6

7 / 1 6

2 1 / 3 2

3

8

1 1 / 2

1 0 1 / 2

4 . 5

0 0

3 / 4

1 / 8

7 1 5

1 5

A

6 ”

R - 4 7

*

1 2 7 / 1 0

1 2 7 / 1 0

2 5 5 / 8

1 8

1 2

1 0

2 0

1 0

1 9

1 4 1 / 2

9

1 / 2

2 5 / 3 2

4 1 / 4

8

2

1 4 1 / 4

6 . 6

2 5

3 / 4

1 / 8

1 , 1

9 5

2 0

A

8 ” R - 5 1

*

1 9 7 / 8

1 9 7 / 8

4 0

2 6

2 0

1 1

3 9

2 0

2 1 3 / 4

1 7 1 / 4

1 1

9 / 1 6

2 9 / 3 2

5

1 2

2

1 5 1 / 2

8 . 6

2 5

3 / 4

1 / 4

1 6

A

1 0 ” R - 5 5

*

2 3 1 / 1 6

2 0 7 / 8

4 4 3 / 1 6

2 7

2 1

1 4

4 1

2 1

2 6 1 / 2

2 1 1 / 4

1 3 1 / 2

1 1 / 1 6

1 3 / 1 6

6 1 / 2

1 2

2 1 / 2

2 0

1 0 . 7

5 0

3 / 4

1 / 4

1 7

A

1 2 ”

R 6 0

*

2 3 1 3 / 1 6

2 0 7 / 8

4 4 1 5 / 1 6

2 7

2 1

1 5

4 1

2 1

3 0

2 4 3 / 8

1 6

1 1 / 1 6

1 5 / 1 6

7 1 / 4

1 2

2 3 / 4

2 2

1 2 . 7

5 0

3 / 4

1 / 4

1 7


l e .




h i g h H

2 S ,

H i g h C O

2 ,

N O R S O K ,

I S O 5 1 6

7 ,

P E D ,

D a n i e l


( 3 ) 2 5 0 0 A N S I S e n i o r O r i f i c e F i t t i n g s a r e

a v a i l a b l e u p t o 1 2 " . C o n s u l t f a c t o r y f o r l a r g e r l i n e

s i z e s .





F l a n g e d - R a i s e d F a c e

( 1 ) 1 0 " t o 1 6 " 1 5 0 t o 6 0 0

A N S I 2 " t o 1 6 " 9 0 0 A N S I

( 1 ) D o u b l e - e n d e d o p e r a t i n g s h a f t s a r e s t a n d a r d .








( 1 ) 2 " t o 8 " 1 5 0 t o 6 0 0 A N

S I

( 1 ) D o u b l e - e n d e d o p e r a t i n g s h a f t s a r e s t a n d a r d .







F l a n g e d - R i n g J o i n t

( 1 ) 1 0 " t o 1 6 " 6 0 0 a n d 2 " t o

1 6 " 9 0 0 A N S I


r d .





Standard Trim(2)

A.P.I. Ring Number


Upstream Face of Orifice Plate to Face of

End

Downstream Face of Orifice Plate to Face

of End




Clearance to Bottom

Centerline to Top


Diameter of Flange



Depth of Groove

Width of Groove

Flange Thickness

Number of Bolt / Studs per Flange

Diameter Flange Bolt / Studs




Weight (lb)


Removal

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L 2

M 1

M 2

N 1

P R

W


4 5 - D a n i e l 1 0 - 1 6 " F l a n g e d - R i n g J o i n t 6 0 0 A N S I

A

1 0 "

R - 5 3

*

9 9 / 1 6

8 1 / 1 6

1 7 3 / 8

1 8

1 2

1 0

2 5

1 4

2 0

1 7

1 2 3 / 4

5 / 1 6

1 5 / 3 2

2

1 / 2

1 6

1 1 / 4

8 3 / 4

3 / 4 1 / 4

9 2 0

2 2

A

1 2 "

R - 5 7

*

9 7 / 8

8 7 / 8

1 9

2 0

1 4

1 1

2 9

1 6

2 2

1 9 1 / 4

1 5

5 / 1 6

1 5 / 3 2

2

5 / 8

1 2

1 1 / 4

9

3 / 4 1 / 4

1 , 4

3 0

2 6

A

1 4 "

R - 6 1

*

1 0 5 / 1 6

1 0 5 / 1 6

2 0 7 / 8

2 1

1 5

1 2

3 2

1 8

2 3 3 / 4

2 0 3 / 4

1 6 1 / 2

5 / 1 6

1 5 / 3 2

2

3 / 4

2 0

1 3 / 8

9 3 / 4

3 / 4 1 / 4

1 , 7

3 5

2 9

A

1 6 " R - 6 5

*

1 0 1 1 / 1 6

1 0 1 1 / 1 6

2 1 3 / 4

2 4

1 8

1 4

3 6

2 0

2 7

2 3 3 / 4

1 8 1 / 2

5 / 1 6

1 5 / 3 2

3

2 0

1 1 / 2

1 0 1 / 2

3 / 8 3 / 8

2 , 3

1 5

3 6


4 6 - D a n i e l 2 - 1 6 " F l a

n g e d - R i n g J o i n t 9 0 0 A N S I ( u s e P T F E S e a l R i n g o r S S R o n l y )

A

2 "

R - 2 4

*

7

7

1 4 1 / 8

1 3

7

5

1 4

6

8 1 / 2

6 1 / 2

3 3 / 4

5 / 1 6

1 5 / 3 2

1

1 / 2

8

7 / 8

6

1 / 2 1 / 8

2 3 0

1 1

A

3 "

R - 3 1

*

7

7

1 4 1 / 8

1 4

8

5

1 5

7

9 1 / 2

7 1 / 2

4 7 / 8

5 / 1 6

1 5 / 3 2

1

1 / 2

8

7 / 8

6

1 / 2 1 / 8

2 4 5

1 1

A

4 "

R - 3 7

*

7 7 / 8

7 1 / 8

1 5 1 / 8

1 5

9

6

1 6

8

1 1 1 / 2

9 1 / 4

5 7 / 8

5 / 1 6

1 5 / 3 2

1

3 / 4

8

1 1 / 8

7

3 / 4 1 / 8

3 5 5

1 3

A

6 " R - 4 5

*

8 5 / 8

8

1 6 3 / 4

1 6

1 0

8

1 9

1 0

1 5

1 2 1 / 2

8 5 / 1 6

5 / 1 6

1 5 / 3 2

2 3 / 1 6

1 2

1 1 / 8

8

3 / 4 1 / 8

6 0 0

1 6

A

8 " R - 4 9

*

9 1 / 8

9 1 / 8

1 8 1 / 2

1 7

1 1

1 0

2 2

1 2

1 8 1 / 2

1 5 1 / 2

1 0 5 / 8

5 / 1 6

1 5 / 3 2

2 1 / 2

1 2

1 3 / 8

9

3 / 4 1 / 4

1 , 2

6 5

2 0

A

1 0 "

R - 5 3

*

1 0 7 / 8

1 0 7 / 8

2 2

1 9

1 3

1 1

2 5

1 4

2 1 1 / 2

1 8 1 / 2

1 2 3 / 4

5 / 1 6

1 5 / 3 2

2 3 / 4

1 6

1 3 / 8

9 1 / 2

3 / 4 1 / 4

1 , 8

0 0

2 6

A

1 2 "

R - 5 7

*

1 1 5 / 8

1 1 5 / 8

2 3 1 / 2

2 1

1 5

1 2

2 9

1 6

2 4

2 1

1 5

5 / 1 6

1 5 / 3 2

3 1 / 8

2 0

1 3 / 8

1 0 1 / 4

3 / 4 1 / 4

2 , 2

6 0

2 8

A

1 4 " R - 6 2

*

1 3

1 2 1 5 / 1 6

2 6 1 / 8

2 3

1 7

1 3

3 2

1 8

2 5 1 / 4

2 2

1 6 1 / 2

7 / 1 6

1 5 / 3 2

3 3 / 8

2 0

1 1 / 2

1 0 1 / 2

3 / 4 1 / 4

2 , 4

9 5

2 9

A

1 6 " R - 6 6

*

1 2 1 3 / 1 6

1 2 1 3 / 1 6

2 6

2 4

1 8

1 4

3 7

2 0

2 7 3 / 4

2 4 1 / 4

1 8 1 / 2

7 / 1 6

2 1 / 3 2

3 1 / 2

2 0

1 3 / 4

1 1

3 / 4 3 / 8

4 , 7

8 1

3 6


l e .

( 2 ) P l e a s e c o n s u l t D a n i e l f a c t o r y o r r e p r e s e n t a t i v e f o r o t h e r t r i m s a v a i l a b l e f o r s e v e r e s e r v i c e a n d o t h e r c o d e r e q u i r e m e n t s ,

i n c l u d i n g l o w - t

e m p e r a t u r e ,

h i g h H

2 S ,

H i g h C O

2 ,

N O R S O K ,

I S O 5 1 6 7 ,

P E D ,

D a n i e l







( 1 ) 2 " t o 8 " 6 0 0 A N S I


r d .





Standard Trim(3)

A.P.I. Ring Number



End


of End

(2)

Overall Face to Face(2)



Clearance to Bottom

Centerline to Top


Diameter of Flange



Depth of Groove

Width of Groove

Flange Thickness

Number of Bolt / Studs per Flange

Diameter Flange Bolt / Studs




Weight (lb)


Removal

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L 2

M 1

M 2

N 1

P

R

W


4 5 - D a n i e l 2 - 8 " F l a n

g e d - R i n g J o i n t 6 0 0 A N S I

N A C E

2 "

R - 2 3

*

8 1 / 2

5 5 / 1 6

1 3 1 5 / 1 6

1 3

7

4

1 4

6

6 1 / 2

5

3 1 / 4

5 / 1 6

1 5 / 3 2

1

8

5 / 8

4 1 / 2

1 / 2

1 / 8

1 1 5

9

N A C E

3 "

R - 3 1

*

1 0 9 / 1 6

7

1 7 1 1 / 1 6

1 4

8

5

1 5

7

8 1 / 4

6 5 / 8

4 7 / 8

5 / 1 6

1 5 / 3 2

1 1 / 4

8

3 / 4

5 1 / 4

1 / 2

1 / 8

1 7 5

1 1

N A C E

4 "

R - 3 7

* 1 0 1 5 / 1 6

6 5 / 8

1 7 1 1 / 1 6

1 5

9

6

1 6

8

1 0 3 / 4

8 1 / 2

5 7 / 8

5 / 1 6

1 5 / 3 2

1 1 / 2

8

7 / 8

6

3 / 4

1 / 8

3 0 0

1 3

N A C E

6 " R - 4 5

* 1 2 1 5 / 1 6

8

2 1 1 / 1 6

1 6

1 0

7

1 9

1 0

1 4

1 1 1 / 2

8 5 / 1 6

5 / 1 6

1 5 / 3 2

1 7 / 8

1 2

1

7

3 / 4

1 / 8

4 8 0

1 6

N A C E

8 " R - 4 9

*

1 4 3 / 1 6

8 3 / 4

2 3 3 / 1 6

1 7

1 1

9

2 2

1 2

1 6 1 / 2

1 3 3 / 4

1 0 5 / 8

5 / 1 6

1 5 / 3 2

2 3 / 1 6

1 2

1 1 / 8

8

3 / 4

1 / 4

7 1 0

1 9


l e .

( 2 ) T h e f l a n g e - b y - f l a n g e ( F x F ) c o n f i g u r a t i o n o f t h e 2 " t o 8 " S e n i o r O r i f i c e F i t t i n g s h a s c h a n g e d .

T h i s c h a n g e a p p l i e s t o A N S I c l a s s e s 1 5 0 t o 6

0 0 o n l y .

T h e f l a n g e - b y - f l a n g e c o n f i g u r a t i o n h a s b

e e n r e p l a c e d

w i t h a r a i s e d - f a c e o r r i n g - t y p e - j o i n t F l a

n g n e k ( R F F N o r R T J F N ) c o n f i g u r a t i o n f e a t u r i n g a f l a n g e w e l d e d t o t h e u p s t r e a m s

i d e ( i n l e t ) o f t h e F l a

n g n e k f i t t i n g .

T h i s m e a n s t h e f a c e - t o - f a c e d i m e n

s i o n s a r e l o n g e r

t h a n p r e v i o u s v e r s i o n s a n d w i l l n o t r e t r o f i t i n t o t h e v o i d o f a n y o l d s t y l e F x F S e n i o r O r i f i c e F i t t i n g p u r c h a s e d p r i o r t o A u g u s t 2 0 1 2 .

T o r e p l a c e d i s c o n t i n u e d F x F m o d e l s , e x i s t i n g p i p i n g m u s t

b e m o d i f i e d t o

a c c o m m o d a t e t h e a d d e d l e n g t h .




h i g h H

2 S ,

H i g h C O

2 ,

N O R S O K ,

I S O 5 1 6

7 ,

P E D ,

D a n i e l “ A A S G ” ,

a n d s p e c i a l a p p l i c a t i o n s .






( 1 ) 2 " t o 1 6 " 1 5 0 0 A N S I a n d 2 " t o 1 2 " 2 5 0 0 A N S I


r d .





Standard Trim(2)


Upstream Face of Orifice Plate to

Face of End


Face of End




Clearance to Bottom

Centerline to Top


Diameter of Flange


Diameter of Raised Face +.000 -.005

Height of Raised Face

Flange Thickness



Length of Bolts / Studs with 2 Hex

Nuts



Weight (lb)

Minimum Clearance for ClampingBar Removal

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L

M

N

P

R

W


0 7 - D a n i e l 2 - 1 6 " F l a

n g e d - R a i s e d F a c e 1 5 0 0 A N S I ( u s e P T F E S e a l R i n g o r S S R o n l y )

A

2 "

*

6 1 5 / 1 6

6

1 5 / 1 6

1 4

1 3

7

5

1 4

6

8 1 / 2

6 1 / 2

3 5 / 8

1 / 4

1 1 / 2

8

7 / 8

5 3 / 4

1 / 2

1 / 8

2 3 0

1

1

A

3 "

*

8 3 / 1 6

7

1 1 / 1 6

1 6

1 4

8

6

1 5

7

1 0 1 / 2

8

5

1 / 4

1 7 / 8

8

1 1 / 8

7

1 / 2

1 / 8

2 7 5

1

3

A

4 "

*

8 3 / 8

7 7 / 8

1 6 3 / 8

1 6

1 0

7

1 7

8

1 2 1 / 4

9 1 / 2

6 3 / 1 6

1 / 4

2 1 / 8

8

1 1 / 4

7 3 / 4

3 / 4

1 / 8

5 2 0

1

6

A

6 "

*

1 0 3 / 4

1 0

3 / 1 6

2 1 1 / 1 6

1 6

1 0

8

2 0

1 0

1 5 1 / 2

1 2 1 / 2

8 1 / 2

1 / 4

3 1 / 4

1 2

1 3 / 8

1 0 1 / 4

3 / 4

1 / 8

8 7 5

2

0

A

8 "

*

1 1 2 3 / 3 2

1 1

5 / 3 2

2 3 1 / 8

1 8

1 2

1 0

2 3

1 2

1 9

1 5 1 / 2

1 0 5 / 8

1 / 4

3 5 / 8

1 2

1 5 / 8

1 1 1 / 2

3 / 4

1 / 4

1 , 5

0 0

2

2

A

1 0 "

*

1 2 5 / 1 6

1 2

5 / 1 6

2 4 7 / 8

1 9

1 3

1 2

2 6

1 4

2 3

1 9

1 2 3 / 4

1 / 4

4 1 / 4

1 2

1 7 / 8

1 3 1 / 2

3 / 4

1 / 4

2 , 1

8 0

2

6

A

1 2 "

*

1 3 5 / 1 6

1 3

5 / 1 6

2 6 7 / 8

2 3

1 7

1 4

2 9

1 6

2 6 1 / 2

2 2 1 / 2

1 5

1 / 4

4 7 / 8

1 6

2

1 4 3 / 4

3 / 4

1 / 4

3 , 4

7 0

3

0

A

1 4 "

*

1 0 1 5 / 1 6

1 5

1 3 / 1 6

2 7 1 / 8

2 7

2 1

1 7

3 5

1 8

2 9 1 / 2

2 5

1 6 1 / 4

1 / 4

5 1 / 4

1 6

2 1 / 4

1 6

3 / 4

1 / 4

C F

3

1

A

1 6 "

*

1 6 7 / 1 6

1 6

1 1 / 1 6

3 3 3 / 4

2 8

2 2

1 7

3 6

2 0

3 2 1 / 2

2 7 3 / 4

1 8 1 / 2

1 / 4

5 3 / 4

1 6

2 1 / 2

1 7 1 / 2

3 / 4

3 / 8

C F

3

6


0 8 - D a n i e l 2 - 1 2 " F l a

n g e d - R a i s e d F a c e 2 5 0 0 A N S I ( u s e S N C o n l y )

A

2 "

*

8 5 / 8

8 5 / 8

1 7 3 / 8

1 6

1 0

6

1 7

8

9 1 / 4

6 3 / 4

3 5 / 8

1 / 4

2

8

1

7

1 / 2

1 / 8

5 6 0

1

3

A

3 "

*

9 9 / 1 6

9

9 / 1 6

1 9 1 / 4

1 6

1 0

6

1 7

8

1 2

9

5

1 / 4

2 5 / 8

8

1 1 / 4

8 3 / 4

1 / 2

1 / 8

6 6 0

1

3

A

4 "

*

1 0 1 / 2

1

0 1 / 2

2 1 1 / 8

1 7

1 1

7

1 7

8

1 4

1 0 3 / 4

6 3 / 1 6

1 / 4

3

8

1 1 / 2

1 0

3 / 4

1 / 8

8 4 0

1

5

A

6 "

*

1 2 1 / 2

1

2 1 / 2

2 5 1 / 8

1 8

1 2

1 0

2 0

1 0

1 9

1 4 1 / 2

8 1 / 2

1 / 4

4 1 / 4

8

2

1 3 3 / 4

3 / 4

1 / 8

1 , 5

2 0

2

0

A

8 "

*

1 9

9 / 1 6

1 9

9 / 1 6

3 9 3 / 8

2 6

2 0

1 1

3 9

2 0

2 1 3 / 4

1 7 1 / 4

1 0 5 / 8

1 / 4

5

1 2

2

1 5

3 / 4

1 / 4

1

6

A

1 0 "

*

2 2

5 / 8

2

2 5 / 8

4 5 1 / 2

2 7

2 1

1 4

4 1

2 1

2 6 1 / 2

2 1 1 / 4

1 2 3 / 4

1 / 4

6 1 / 2

1 2

2 1 / 2

1 9 1 / 4

3 / 4

1 / 4

1

7

A

1 2 "

*

2 3

3 / 8

2

3 3 / 8

4 7

2 7

2 1

1 5

4 1

2 1

3 0

2 4 3 / 8

1 5

1 / 4

7 1 / 4

1 2

2 3 / 4

2 1 1 / 4

3 / 4

1 / 4

1

7


l e .




h i g h H

2 S ,

H i g h C O

2 ,

N O R S O K ,

I S O 5 1 6

7 ,

P E D ,

D a n i e l “ A A S G ” ,

a n d s p e c i a l a p p l i c a t i o n s .






( 1 ) 2 " t o 1 6 " 1 5 0 0 A N S I a n d 2 " t o 1 2 " 2 5 0 0 A N S I


r d .





Standard Trim(2)

A.P.I. Ring Number



End


of End




Clearance to Bottom

Centerline to Top


Diameter of Flange



Depth of Groove

Width of Groove

Flange Thickness

Number Of Bolts / Studs per Flange





Weight (lb)

Minimum Clearance for Clamping BarRemoval

S I Z E

A

B

C

D

F

G

H

I

I 1

J

K

L 2

M 1

M 2

N 1

P

R

W


4 7 - D a n i e l 2 - 1 6 " F l a

n g e d - R i n g J o i n t 1 5 0 0 A N S I ( u s e P T F E S e a l R

i n g o r S S R o n l y )

A

2 "

R - 2 4

*

7

7

1 4 1 / 8

1 3

7

5

1 4

6

8 1 / 2

6 1 / 2

3 3 / 4

5 / 1 6

1 5 / 3 2

1 1

/ 2

8

7 / 8

6

1 / 2

1 / 8

2 3 0

1

1

A

3 "

R - 3 5

*

8 1 / 4

7 3 / 4

1 6 1 / 8

1 4

8

6

1 5

7

1 0 1 / 2

8

5 3 / 8

5 / 1 6

1 5 / 3 2

1 7

/ 8

8

1 1 / 8

7 1 / 4

1 / 2

1 / 8

3 2 5

1

3

A

4 "

R - 3 9

*

8 7 / 1 6

7 1 5 / 1 6

1 6 1 / 2

1 6

1 0

7

1 7

8

1 2 1 / 4

9 1 / 2

6 3 / 8

5 / 1 6

1 5 / 3 2

2 1

/ 8

8

1 1 / 4

8

3 / 4

1 / 8

5 2 0

1

6

A

6 "

R - 4 6

*

1 0 7 / 8

1 0 5 / 1 6

2 1 9 / 1 6

1 6

1 0

8

2 0

1 0

1 5 1 / 2

1 2 1 / 2

8 5 / 1 6

3 / 8

1 7 / 3 2

3 1

/ 4

1 2

1 3 / 8

1 0 1 / 2

3 / 4

1 / 8

8 7 5

2

0

A

8 "

R - 5 0

*

1 1 2 9 / 3 2

1 1 1 1 / 3 2

2 3 1 / 2

1 8

1 2

1 0

2 3

1 2

1 9

1 5 1 / 2

1 0 5 / 8

7 / 1 6

2 1 / 3 2

3 5

/ 8

1 2

1 5 / 8

1 2

3 / 4

1 / 4 1 , 5

0 0

2

2

A

1 0 "

R - 5 4

*

1 2 1 / 2

1 2 1 / 2

2 5 1 / 4

1 9

1 3

1 2

2 6

1 4

2 3

1 9

1 2 3 / 4

7 / 1 6

2 1 / 3 2

4 1

/ 4

1 2

1 7 / 8

1 3 3 / 4

3 / 4

1 / 4

2 , 1

8 0

2

6

A

1 2 "

R - 5 8

*

1 3 5 / 8

1 3 5 / 8

2 7 1 / 2

2 3

1 7

1 4

2 9

1 6

2 6 1 / 2

2 2 1 / 2

1 5

9 / 1 6

2 9 / 3 2

4 7

/ 8

1 6

2

1 5 1 / 4

3 / 4

1 / 4 3 , 4

7 0

3

0

A

1 4 "

R - 6 3

*

1 0 1 5 / 1 6

1 5 1 3 / 1 6

2 7 1 / 8

2 7

2 1

1 7

3 5

1 8

2 9 1 / 2

2 5

1 6 1 / 4

5 / 8

1 1 / 1 6

5 1

/ 4

1 6

2 3 / 8

1 5 3 / 4

3 / 4

1 / 4

C F

3

1

A

1 6 "

R - 6 7

*

1 7 1 / 8

1 7 1 / 8

3 4 5 / 8

2 8

2 2

1 7

3 6

2 0

3 2 1 / 2

2 7 3 / 4

1 8 1 / 2

6 4 / 9 3

1 3 / 1 6

5 3

/ 4

1 6

2 1 / 2

1 7 1 / 4

3 / 4

3 / 8

C F

3

6


4 8 - D a n i e l 2 - 1 2 " F l a

n g e d - R i n g J o i n t 2 5 0 0 A N S I ( u s e S N C o n l y )

A

2 "

R - 2 6

*

8 1 1 / 1 6

8 1 1 / 1 6

1 7 1 / 2

1 6

1 0

6

1 7

8

9 1 / 4

6 3 / 4

4

5 / 1 6

1 5 / 3 2

2

8

1

7 1 / 4

1 / 2

1 / 8

5 6 0

1

3

A

3 "

R - 3 2

*

9 1 1 / 1 6

9 1 1 / 1 6

1 9 1 / 2

1 6

1 0

6

1 7

8

1 2

9

5

3 / 8

1 7 / 3 2

2 5

/ 8

8

1 1 / 4

9

1 / 2

1 / 8

6 6 0

1

3

A

4 "

R - 3 8

*

1 0 1 1 / 1 6

1 0 1 1 / 1 6

2 1 1 / 2

1 7

1 1

7

1 7

8

1 4

1 0 3 / 4

6 3 / 1 6

7 / 1 6

2 1 / 3 2

3

8

1 1 / 2

1 0 1 / 2

3 / 4

1 / 8

8 4 0

1

5

A

6 "

R - 4 7

*

1 2 3 / 4

1 2 3 / 4

2 5 5 / 8

1 8

1 2

1 0

2 0

1 0

1 9

1 4 1 / 2

9

1 / 2

2 5 / 3 2

4 1

/ 4

8

2

1 4 1 / 4

3 / 4

1 / 8

1 , 5

2 0

2

0

A

8 "

R - 5 1

*

1 9

7 / 8

1 9

7 / 8

4 0

2 6

2 0

1 1

3 9

2 0

2 1 3 / 4

1 7 1 / 4

1 1

9 / 1 6

2 9 / 3 2

5

1 2

2

1 5 1 / 2

3 / 4

1 / 4

1

6

A

1 0 "

R - 5 5

*

2 3

1 / 1 6

2 3

1 / 1 6

4 6

3 / 8

2 7

2 1

1 4

4 1

2 1

2 6 1 / 2

2 1 1 / 4

1 3 1 / 2

1 1 / 1 6

1 3 / 1 6

6 1

/ 2

1 2

2 1 / 2

2 0

3 / 4

1 / 4

1

7

A

1 2 "

R - 6 0

*

2 3 1 3 / 1 6

2 3 1 3 / 1 6

4 7

7 / 8

2 7

2 1

1 5

4 1

2 1

3 0

2 4 3 / 8

1 6

1 1 / 1 6

1 5 / 1 6

7 1

/ 4

1 2

2 3 / 4

2 2

3 / 4

1 / 4

1

7


l e .




h i g h H

2 S ,

H i g h C O

2 ,

N O R S O K ,

I S O 5 1 6

7 ,

P E D ,

D a n i e l “ A A S G ” , a n d s p e c i a l a p p l i c a t i o n s .





DanielTM SeniorTM Orifice Fitting Selection Matrix

6

BASIC TYPE / PRIMARY FUNCTIONNominal line size 6"Internal diameter 6.065

Fitting StyleRaised Face Flangnek 01Raised Face Flanged 10Ring Joint Flangnek 014Ring Joint Flanged 14

ANSI150# 1300# 3600# 5900# 61500# 72500# 8

Orifice Plate SealsRemovable Dual Seal*(up to 12") DSCDual Volcanized Seal*(16" and up) 3DVSRemovable PTFE Seal (up to 24") TSCRemovable Metal Seal (up to 24") MSCRemovable Snap Seal*(up to 20") SNC

Internal trim materialStandard ASour Gas / Corrosive Service AASGNACE (standard 2" to 8") 150 - 600 ANSI NACE

When ordering, please specify: Catalog Number, Plate Material, Plate Bore(s) and Quantity.

Note: All products and components are subject to change without notice in a continuing effort of product improvement.





©2013 Daniel Measurement and Control, Inc. All Rights Reserved. Unauthorized duplication in

whole or in part is prohibited. Printed in the USA. DAN-SOF-TECH-GUIDE-0513

Daniel Measurement and Control, Inc. (“Daniel”) is an Emerson Process Management businessunit. The Daniel name and logo are trademarks of Daniel Industries, Inc. The Emerson logo isa trademark and service mark of Emerson Electric Co. Parker is a trademark of Parker HannifinCorporation.

Emerson Process Management

Daniel Measurement and Control, Inc.North America / Latin America:HeadquartersUSA - Houston, TexasT +1.713.467.6000USA Toll Free 1.888.FLOW.001

www.Daniel.com

Europe: Stirling, Scotland, UKT +44.1786.433400Middle East, Africa: Dubai, UAET +971.4.811.8100Asia Pacific: SingaporeT +65.6777.8211

Scan with your smartphone for moreinformation

Documents

Daniel Senior Orifice Fitting Tech Guide