Customer Service: Web Site: · PDF file©2009 delta enterprise corp. ... r. foam pad k.50mm bolt x 4 l.32mm bolt x 16 m. 17mm bolt x 8. 5 section 1: crib assembly step 1 parts and

©2009 DELTA ENTERPRISE CORP.

THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.

If you have any questions or missing parts, contact us. DO NOT return product parts to the store from where it was purchased before contacting Delta Children’s Products Customer Service.

Customer Service:Web Site: www.deltachildrensproducts.com

Delta Children’s Products114 West 26th StreetNew York, NY 10001 Tele.212-645-9033

MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.THE APPEARANCE OF YOUR PRODUCT MAY BE DIFFERENT FROM THAT PICTURED IN THIS BOOK.

READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF PRODUCT.KEEP INSTRUCTIONS FOR FUTURE USE.

ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY.

To register your product for important safety alerts and updates to your product please visit http://deltaenterprise.com/register.asp

NOVEMBER 23, 2009 4490-R6

Conforms to ASTM F406

Safety Standards

WARNING:INFANTS CAN SUFFOCATE

* IN GAPS BETWEEN A MATTRESS TOO SMALL OR TOO THICK AND PRODUCT SIDES.*ON SOFT BEDDING. NEVER ADD A MATTRESS, PILLOW, COMFORTER OR PADDING.

USE ONLY THE MATTRESS PROVIDED BY DELTA CHILDREN’S PRODUCTS. (WHICH MUST BE AT LEAST 36 1/2 INCHES LONG BY 22 INCHES WIDE AND NOT MORE THAN 2 INCHES THICK.)

WARNINGFAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT

IN SERIOUS INJURY OR DEATH.TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS BE PLACED

ON THEIR BACKS TO SLEEP, UNLESS OTHERWISE ADVISED BY YOUR PHYSICIAN.

*STRINGS CAN CAUSE STRANGULATION! NEVER PLACE ITEMS WITH A STRING AROUND A CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. NEVER SUSPEND STRINGS OVER PRODUCT OR ATTACH STRINGS TO TOYS.*THE PRODUCT, INCLUDING SIDE RAILS, MUST BE FULLY ERECTED PRIOR TO USE.*NEVER PLACE PRODUCT NEAR A WINDOW WHERE CORDS FROM BLINDS OR DRAPES CAN STRANGLE A CHILD.* WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST ADJUSTMENT POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT. *DISCONTINUE USE OF THE PRODUCT WHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE HEIGHT OF 35 IN. (890 mm).*NEVER USE THIS PRODUCT IF THERE ARE ANY LOOSE OR MISSING FASTENERS, LOOSE JOINTS OR BROKEN PARTS. CHECK BEFORE ASSEMBLY AND FREQUENTLY DURING USE.CONTACT DELTA CHILDREN’S PRODUCTS FOR REPLACEMENT PARTS. NEVER SUBSTITUTE PARTS.*NEVER USE A WATER MATTRESS WITH THIS CRIB.*IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.*NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS NOT SOLD AND INTENDED FOR THAT PURPOSE. THEY CAN CAUSE SUFFOCATION.*ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING REGULARLY, BEFORE PLACING THE CHILD IN THE PRODUCT, THAT EVERY COMPONENT IS PROPERLY AND SECURELY IN PLACE.*TO AVOID HEAD INJURY, DO NOT ALLOW ANY CHILD TO PLAY UNDERNEATH THE PRODUCT.*ALWAYS PROVIDE THE SUPERVISION NECESSARY FOR THE CONTINUED SAFETY OF YOUR CHILD. WHEN USED FOR PLAYING NEVER LEAVE CHILD UNATTENDED.

CAUTION: ANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 36 1/2 INCHES LONG BY 22 INCHES WIDE AND NOT MORE THAN 2 INCHES THICK.

2

PARTS

3

A. BACK RAIL BOTTOM

B. BACK RAIL TOP

C. REAR LEG LEFTD. REAR LEG RIGHT

E. FRONT LEG LEFTF. FRONT LEG RIGHT

G. FRONT RAIL BOTTOM

H. FRONT RAIL TOP

J. MATTRESS SUPPORT

P.CRIB ENDS x2

POUCH ATTACHED TO MATTRESS SUPPORT - KEEP INSTRUCTIONS AND ANY EXTRA HARDWARE AND TOOLS IN THIS POUCH AFTER ASSEMBLYWARNINGS RELATED TO THE SAFE USE OF THIS CRIB ARE PRINTED ON THE POUCH

4

PARTS - HARDWARE AND TOOLS

M4 ALLEN WRENCH SUPPLIED

N. DOWEL x2

ALL HARDWARE ON THIS PAGE IS SHOWN FULL SIZE AND WITH THE CORRECTDESIGN.THE PARTS CAN BE MATCHED TO THE PICTURES.

R. FOAM PAD

K.50mm BOLT x 4

L.32mm BOLT x 16

M. 17mm BOLT x 8

5

SECTION 1: CRIB ASSEMBLYSTEP 1

PARTS AND TOOLS REQUIRED TO COMPLETE STEP

A. BACK RAIL BOTTOMC. REAR LEG LEFT

D. REAR LEG RIGHT


ATTACH THE BACK RAIL BOTTOM (PART A) TO THE REAR LEG LEFT (PART C) AND THE REAR LEG RIGHT (PART D) WITH (4) M6x32mm BOLTS (PART L) USING THE M4 ALLEN WRENCH AS SHOWN.

A

C

D

LL

LL

LL

LL

NOTE : THE SLOT IN PART A MUST FACE UP.

L. 32mm BOLT x 4

6



FROM STEP 1M4 ALLEN WRENCH SUPPLIED

INSERT THE TENON OF THE BACK RAIL TOP (PART B) INTO THE SLOT ON TOP OF THE BACK RAILBOTTOM (PART A), THEN INSERT THE M6x32 mm BOLTS (PART L), THROUGH THE REAR LEGSINTO THE THREADED INSETS ONTO THE BACK RAIL TOP (PART B) AS SHOWN.

B. BACK RAIL TOP

LL

A

LL

B

L. 32mm BOLT x 2

7




ATTACH THE FRONT LEG LEFT (PART E) AND FRONT LEG RIGHT (PART F) TO THE CRIB ENDS(PART P) WITH (4) M6x32 mm BOLTS (PART L) USING THE M4 ALLEN WRENCH AS SHOWN.

P.CRIB ENDS x2

E. FRONT LEG LEFTF. FRONT LEG RIGHT

P

P

E

F

L

L

L

L

L.32mm BOLT x 4

8




ATTACH THE ASSEMBLY FROM STEP 2 TO THE ASSEMB LIES FROM STEP 3 WITH (4) M6x50 mm BOLTS(PART K) AND (2) DOWELS (PART N) USING THE M4 ALLEN WRENCH AS SHOWN.

K

FROM STEP 2

FROM STEP 3

K

K

K

N. DOWEL x2

K.50mm BOLT x 4

N

N

9




ATTACH THE MATTRESS SUPPORT (PART J) TO THE ASSEMBLY FROM STEP 4 WITH (4)17mm BOLTS (PART M) USING THE M4 ALLEN WRENCH SUPPLIED.THERE ARE (3) POSITIONS FOR THE MATTRESS SUPPORT.USE THE HIGHEST ONLY FORNEW BORNS.MOVE THE MATTRESS DOWN AS THE CHILD GROWS.

FROM STEP 4

M

J. MATTRESS SUPPORT

J

M

M

M

M

J

ALL CORNERS

! WARNINGS ON POUCH MUST FACE UP.

THIS SIDE UP.

M. 17mm BOLT x 4

10




ATTACH THE FRONT RAIL BOTTOM (PART G) TO THE ASSEMBLY FROM STEP 5 WITH (4)M6x32 mm BOLTS (PART L) USING THE M4 ALLEN WRENCH AS SHOWN.

FROM STEP 5

G

LL

LL

LL

G. FRONT RAIL BOTTOM

L

NOTE : THE SLOT IN PART GMUST FACE UP.

L.32mm BOLT x 4

11



M4 ALLEN WRENCH SUPPLIEDFROM STEP 6

LL

L

H. FRONT RAIL TOP

H

INSERT THE TENON OF THE FRONT RAIL TOP (PART H) INTO THE SLOT ON TOP OF THE FRONTRAIL BOTTOM (PART G) OF THE ASSEMBLY FROM STEP 6 , THEN INSERT THE M6x32 mm BOLTS(PART L),THROUGH THE RRONT LEGS INTO THE THREADED INSETS ONTO THE FRONT RAILTOP (PART H) AS SHOWN.

L.32mm BOLT x 2

12



FROM STEP 7 R. FOAM PAD

P

PLACE THE FOAM PAD (PART R) ONTO THE MATTRESS SUPPORT (PART J) AS SHOWN.

SECTION 2: TWIN BED CONVERSION

13


M4 ALLEN WRENCHSUPPLIED

THIS CRIB CAN BE CONVERTED INTO A TWIN BED HEADBOARD. THE ASSEMBLY FROMSTEP 2 IS THE HEADBOARD FOR THE TWIN BED. REMOVE ALL PARTS INSTALLED AFTERSTEP 2,IN REVERSE ORDER,AND STORE THEM SAFELY.

STAND HEADBOARD UP. USE THE 17MM BOLTS(PART M) TO ATTACHTHE HEADBOARD TO THE BED FRAME, CONTACT DELTA CHILDREN’SPRODUCTS WITH QUESTIONS.

NOTE: BED FRAMES ARE NOT SUPPLIED WITH THISSYSTEM, BUT CAN BE PURCHASED AT MATTRESSSTORES.

M. 17mm BOLT x 4

Warranty: This Delta Crib is warranted to be free from defects for a period of 1 year from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.

Please do not return this item to the store before contacting us about missing parts or with any questions.

Customer Service:Web Site: www.deltachildrensproducts.com

Delta Children’s Products114 West 26th StreetNew York, NY 10001

Tele.212-645-9033

To register your product for important safety alerts and updates to your product please visit http://deltaenterprise.com/register.asp

In the event that you need to contact our customer service department please have the Style Number and Lot Number available. To report a problem, please log on to www.deltachildrensproducts.com and click the Customer Service Tab, or log on to www.deltaenterprise.com/customer_service.asp, or contact us by phone at (212) 645-9033.

Use the space below to make note of those numbers. They can be found on the label on Crib End bottom rail.

Style No.:______________________

Lot No. : _______________________

Pack Date:_____________________

Date of Purchase: _____________ (you should also keep your receipt)

Documents

Customer Service: Web Site: · PDF file©2009 delta enterprise corp. ... r. foam pad k.50mm bolt x 4 l.32mm bolt x 16 m. 17mm bolt x 8. 5 section 1: crib assembly step 1 parts and