Upload
bernardo-uriostegui-cadena
View
227
Download
0
Embed Size (px)
Citation preview
8/7/2019 automovil - tuning - lambo installation
1/2
2002 The Hoffman Group L.L.C. All rights reserved.
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the aboveinstructions. Installation by qualified automotive professionals is highly recommended. LAMBO-UN 1 of 2 6.2 5.03
LAMBO HINGE SYSTEMUSER GUIDE AND INSTALLATION MANUAL
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
Patent Pending
LAMBO-UN -universal lambo hinge system
DOOR
10
LOWER HINGELOWER BRACKET
UPPER HINGE
DOOR
CAR
DOOR
CAR
DOOR
CAR
13
7
4
9
CAR
6
DOOR
5
2
3
4
5
6
7
8
9
Remove fender and top door hinge
Close vehicle door. NOTE: make sure thdoors are properly seated.
IMPORTANT Mount the upper hinge usthe existing door hinge holes. It is key tomount the upper hinge as high as posswithout interfering with the fender or dMake sure all parts are level and seatetight against the inner fender and doo
all times.
Hold the upper Lambo hinge assemblylevel and flush with the inner fender anthe door. Outline the location of the uphinge on the car and door.
Measure vehicle's bolt hole patternrelative to the outline(step 3) and copthese measurements to the upper hingDrill holes in upper hinge. NOTE: Detentshould match a Hondas bolt pattern.
Bolt the upper Lambo hinge to the doNOTE: It may be necessary to drill newholes in the door if your door bolt pattedoesn't match the Lambo bolt patterntapered flat head bolts, not included.
Bolt Upper Hinge to the vehicle. Stock should work if not use Grade 8 bolts.
Hold the lower bracket level and flush the inner fender. Outline the location othe bracket on the car.
Measure vehicle's lower hinge bolt patrelative to the outline(step 7) and copthese measurements to the lower bracDrill holes in the lower bracket.NOTE: Bpattern should match a Hondas.
Bolt lower bracket to the vehicle.
Installation
8/7/2019 automovil - tuning - lambo installation
2/2
2002 The Hoffman Group L.L.C. All rights reserved.
The above instructions are for reference only. THG LLC is not responsible for any inaccuracies in the above instructions. THG LLC is also not responsible for any property damage or personal injuries resulting from the aboveinstructions. Installation by qualified automotive professionals is highly recommended. LAMBO-UN 1 of 2 6.25.03
LAMBO HINGE SYSTEMUSER GUIDE AND INSTALLATION MANUAL
TECH SUPPORT: 503.693.1918 WWW.AUTOLOC.COM
Patent Pending
A
B
C D
E
1
3
4
2
6
5
G
F
VEHICLE TOP VIEW
DOOR
WARNING: This product isdesigned for off road use
only. Professional installationis highly recommended.
RUBPLATE
LOWERBRA
CKET
STRUT
LINEARAC
TUATOR
LOWER HINGE
DISTANC
E=9.9in.
Optional Equipment
Available!
An optional linear actuator andelectronic controller is available.
Please contact your sales rep .
11
10
11
12
13
14
15
16
Bolt the lower hinge to the door. NOTE: Itmay be necessary to drill new holes in the
door if your door bolt pattern doesn'tmatch the Lambo bolt pattern. Stockbolts should work if not use Grade 8 bolts.
Measure 9.9 in. from the center of thelower hinge hole to the lower bracket.
Drill and Thread Hole [8 mm 1.25]
Attach strut to the lower hinge.
IMPORTANT For installation with our linearactuator refer to the insert with these
instructions.
Carefully open the door and attach theother end of the strut to the mountingplate.
Repeat the above steps for the otherdoor to complete installation
See Fine Tuning to adjust door movement
Fine Tuning Once you have the main components installed, it's time to do some finetuning to insure proper operation. You have six adjustment options.Upper Hinge Bracket HolesThe location of the upper hinge and thedrilled holes determines the doors pivotpoint.[adjusts points A & E]
Upright Adjustment RodThe length determines the amount thedoor will go out and away from thevehicle before it travels up.[adjustspoint G]
Vertical Set ScrewAdjusts distance between the bottomrear edge of the door and the doorframe.[adjusts points C & D]
Slotted Door HolesAllows you to adjust how the top of tdoor flushes out with the fender.[adjupoints F]
Rub PlateThe thicknees and how you sculpt the
rub plate determines how the bottomedge of the door flushes out.[adjustspoints C]
Strut HolesWhere you drill the strut / actuator hoon the lower bracket determines howthe door will open.[adjusts points B]
1
2
3
4
5
6