ANM2000 Installation Guide Version B

e-Fim ANM2000

Broadband Access Network Management System

Installation Manual (Based on Windows) Version: B

Code: MN000000366

FiberHome Telecommunication Technologies Co., Ltd.

July 2010

Thank you for choosing our products.

We appreciate your business. Your satisfaction is our

goal. We will provide you with comprehensive technical

support and after-sales service. Please contact your

local sales representative, service representative or

distributor for any help needed at the contact information

shown below.

Fiberhome Telecommunication Technologies Co., Ltd.

Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China

Zip code: 430073

Tel: +86-27-87691549

Fax: +86-27-87691755

Website: http://www.fiberhomegroup.com

Legal Notice

are trademarks of FiberHome Telecommunication Technologies Co., Ltd. (Hereinafter referred to as FiberHome) All brand names and product names used in this document are used foridentification purposes only and are trademarks or registered trademarksof their respective holders.

All rights reserved

No part of this document (including the electronic version) may bereproduced or transmitted in any form or by any means without prior written permission from FiberHome. Information in this document is subject to change without notice.

TM

TMTM

I

Preface

The ANM2000 is an integrated broadband access management platform developed by FiberHome, which can perform the effective and unified management of multiple types of broadband access equipment developed by FiberHome. This manual describes the installation methods of the ANM2000 with the version Build05.07.05.xx.

Relevant Manuals

Manual Description e-Fim ANM2000 Broadband Access Network Management System Operation Manual (Based on

Windows)

This manual describes the ANM2000 common operations

and maintenance methods for the purpose of helping users

know the ANM2000 further and operate it well.

II

Version

Version Instruction A The initial version.

B

Compared with version A, the installation methods of the Informix are modified, and the FAQ is added. Corresponds to the Informix 11.5 version, and the ANM2000 V3.0R2 Build05.07.05.xx version.

Intended Readers

This manual is intended for the following readers:

Commissioning engineers

Construction engineers

FiberHome engineers

III

Conventions

Terminology Conventions

Terminology Meaning

ANM2000 FiberHome e-Fim ANM2000 Broadband Access Network Management System

Informix The database software used together with the ANM2000, developed by IBM

Symbol Conventions

Symbol Refer to Meaning

Note Important features or operation guide.

Caution

Possible injury to persons or systems, or cause traffic

interruption or loss.

Warning May cause severe bodily injuries.

Contents

Preface .................................................................................................................... IRelevant Manuals .............................................................................. IVersion ........................................................................................ IIIntended Readers ............................................................................. IIConventions ..................................................................................... III

1 Overview ...................................................................................................... 1-11.1 Working Mode ................................................................................ 1-21.2 Configuration Requirements .......................................................... 1-2

1.2.1 Requirements of Hardware Configuration .................... 1-21.2.2 Requirements of Software Configuration ...................... 1-3

1.3 Installation Flow Diagrams ............................................................. 1-41.3.1 Initial Installation ........................................................... 1-41.3.2 Upgrade ....................................................................... 1-5

2 Installation of the Informix Database ............................................................ 2-12.1 Installation of the Informix11.5 Dynamic Database ........................ 2-22.2 Installation of the Informix Client-SDK .......................................... 2-112.3 Setting of the Environment Variables ........................................... 2-162.4 Verifying the Informix Database Installation ................................. 2-25

3 Installation of the ANM2000 ......................................................................... 3-13.1 Installation of the Server End ......................................................... 3-2

3.1.1 Running the ANM2000_Server Installation Package .... 3-23.1.2 Creating the Tablespace ............................................... 3-73.1.3 Initializing the Table Architecture .................................. 3-93.1.4 Starting the Service .................................................... 3-103.1.5 Verifying the ANM2000s Server End Installation ....... 3-10

3.2 Installation of the Client End ........................................................ 3-113.2.1 Running the ANM2000_Client Installation Package ... 3-113.2.2 Verifying the ANM2000s Client End Installation ......... 3-15

4 Upgrade of the ANM2000 ............................................................................. 4-14.1 The Upgrade of the Server End ..................................................... 4-2

4.1.1 Preparation before the Upgrade Operation .................. 4-24.1.2 Backup of the Original Configuration Files ................... 4-24.1.3 Backup of the Software Package ................................. 4-34.1.4 Uninstalling the Current ANM2000 ............................... 4-44.1.5 Installing the ANM2000 of the Upgrade Version ........... 4-54.1.6 Importing the Configuration Data ................................. 4-64.1.7 Verifying the Upgraded Software Version ..................... 4-74.1.8 Checking the Configuration Data ................................. 4-8

4.2 The Upgrade of the Client End ....................................................... 4-94.2.1 Preparation before the Upgrade Operation .................. 4-94.2.2 Uninstalling the Current Client end ............................... 4-94.2.3 Installing the Client End with the Upgrade Version ..... 4-114.2.4 Verifying the Upgraded Software Version ................... 4-11

5 FAQs ............................................................................................................ 5-15.1 How to Handle the Invalid Configuration File ................................. 5-25.2 How to Handle the Long-Period No Response from the ANM2000 5-45.3 How to Handle the Inadequate Disk Space .................................... 5-55.4 How to Handle the Informix Database Not Installed ....................... 5-65.5 How to Handle the Connection Failure of the ANM2000 ................ 5-65.6 How to Handle the Tablespace Creation Failure ............................ 5-85.7 How to Determine the IP Address Bound with the Database ......... 5-9 5.8 How to Handle the Data Exporting / Importing Failure ................. 5-10

Figures

Figure 1-1 The flow of installing the Server end for the first time ...................... 1-4Figure 1-2 The flow of installing the Client end for the first time ....................... 1-5Figure 1-3 The flow of upgrading the Server end .............................................. 1-6Figure 1-4 The flow of upgrading the Client end ............................................... 1-7Figure 2-1 The status that the port 6000 is occupied ........................................ 2-8Figure 2-2 The Server Information tab .......................................................... 2-16Figure 2-3 Setting the Informix user password ............................................... 2-17Figure 2-4 Setting the INFORMIXDIR ............................................................. 2-18Figure 2-5 Setting the INFORMIXSERVER .................................................... 2-19Figure 2-6 Creating system variables (1) ........................................................ 2-21Figure 2-7 Creating system variables (2) ........................................................ 2-21Figure 2-8 Modifying the ROOTSIZE .............................................................. 2-23Figure 2-9 Modifying the LOGFILES ............................................................... 2-23Figure 2-10 The status of the normal starting of the database ........................ 2-25Figure 2-11 The valid status of the configuration file ....................................... 2-26Figure 3-1 Creating the tablespace ................................................................... 3-8Figure 3-2 The status of the successful creation of the tablespace .................. 3-8Figure 3-3 Initializing the Table architecture ...................................................... 3-9Figure 3-4 The status of the successful initialization of the Table architecture .. 3-9

Tables

Table 1-1 Requirements of hardware configuration on the Server end ............. 1-2Table 1-2 Requirements of hardware configuration on the Client end............... 1-3Table 2-1 The database user information .......................................................... 2-6Table 2-2 The database parameters ................................................................. 2-7Table 2-3 The store location information ........................................................... 2-8Table 5-1 Parameter values in the ONCONFIG file .......................................... 5-4Table 5-2 The parameters for creating the tablespace ...................................... 5-5

Version: B 1-1

1 Overview

Before installing the ANM2000, you need to be familiar with the ANM2000s working mode, and to install the software matching the working mode, so as to ensure that the installation can be completed successfully.

This chapter includes the following contents:

Working mode Configuration requirements Installation flow diagrams

e-Fim ANM2000 Broadband Access Network Management System Installation Manual (Based on Windows)

1-2 Version: B

1.1 Working Mode

At present, the ANM2000 uses the Client end-Server end working mode.

When the network maintenance engineers are far from both the access equipment and the network management system server, this Client end-Server end working mode can be used to access the server via the Client end for achieving the purpose of managing the equipment. In this case, the ANM2000s Client end and Sever end can be installed on one computer, or respectively on two computers. When both the Client end and server end are installed on a computer, this is also called a stand-alone mode.

1.2 Configuration Requirements

1.2.1 Requirements of Hardware Configuration

The requirements of the hardware configuration for the ANM2000s Server end depend on the network scale. The detailed requirements are listed in Table 1-1.

Table 1-1 Requirements of hardware configuration on the Server end

Network Scale CPU Clock Rate CPU Number Memory Harddisk Space

Harddisk Format NIC

200 to 500 OLTs, connected with the full-configuration ONUs

Intel Xeon processor X7460, 2.66 GHz

4 16G DDR3 (UDIMM), 1333 MHz

2*300 GB, the space of drive D should be not less than 73 GB

Both drive C and drive D use the NTFS format

Embedded NC326i PCI Express bi-port GE server adaptor


Intel Xeon processor X7350, 2.93 GHz


2*146GB, the space of drive D should be not less than 15 GB


Embedded NC326i PCI Express bi-port GE server adaptor

Less than 100 OLTs, connected with the full-configuration ONUs

Intel Xeon processor E5506, 3 GHz


2*146GB, the space of drive D should be not less than 5 GB


Embedded HP NC107i PCI-Express bi-port GE server adaptor

1 Overview

Version: B 1-3

The requirements of the hardware configuration on the ANM2000s Client end are listed in Table 1-2.

Table 1-2 Requirements of hardware configuration on the Client end

Network Scale CPU Clock Rate CPU Number Memory Harddisk Space

Harddisk Format Display Card


Intel Core 2 processor, 2 GHz


250 GB, the space of drive D should be not less than 15 GB


32M video memory






32M video memory

Less than 100 OLTs, connected with the full-configuration ONUs





32M video memory

1.2.2 Requirements of Software Configuration

The software configuration of the computer acting as the ANM2000s Server end should meet the following requirements:

The legal Windows XP professional SP2, Windows2003server, or Windows2008 standard operating system has been installed on the computer.

The operating system must be 64-bit.

The operator has assigned a fixed IP address for the network management system and configured this IP address for the computer.

The software configuration of the computer acting as the ANM2000s Client end should meet the following requirements:

The legal Windows XP, Windows2003, Windows2008, Windows Vista, or Windows7 operating system has been installed on the computer.


1-4 Version: B

1.3 Installation Flow Diagrams

1.3.1 Initial Installation

Installing the Server end for the first time

When you install the ANM2000s Server end for the first time, please refer to the installation flow illustrated in Figure 1-1. If some problems arise during the installation, please refer to Chapter 5 FAQ.

Figure 1-1 The flow of installing the Server end for the first time

1 Overview

Version: B 1-3

Installing the Client end for the first time

When you install the ANM2000s Client end for the first time, please refer to the installation flow illustrated in Figure 1-2. If some problems arise during the installation, please refer to Chapter 5 FAQ.

Figure 1-2 The flow of installing the Client end for the first time

1.3.2 Upgrade

Upgrading the Server end

When it is necessary to upgrade the ANM2000s Server end, please refer to the installation flow illustrated in Figure 1-3. If some problems arise during the installation, please refer to Chapter 5 FAQ.

1-5


1-6 Version: B

Figure 1-3 The flow of upgrading the Server end

1 Overview

Version: B 1-3

Upgrading the Client end

When it is necessary to upgrade the ANM2000s Client end, please refer to the installation flow illustrated in Figure 1-4. If some problems arise during the installation, please refer to Chapter 5 FAQ.

Figure 1-4 The flow of upgrading the Client end

Version: B 2-1

2 Installation of the Informix Database

The ANM2000 of the V3.0 build 05.07.05.02 version is used together with the Informix11.5 database; if you use the ANM2000 of the V3.0 build 05.07.04.xx, please install the Informix9.4 database. This chapter introduces the installation and setting methods of the Informix11.5 database.


Installation of the Informix11.5 dynamic database Installation of the Informix Client-SDK Setting of the environment variables Verifying the Informix database installation


2-2 Version: B

2.1 Installation of the Informix11.5 Dynamic Database

The ANM2000 is used together with the Informix database. Before installing the ANM2000, please install the Informix database first.

Prerequisites

The hardware and software configuration of the server should meet the requirements instructed in Section 1.2 Configuration Requirements.

The operator has assigned a fixed IP address for the network management server.

Operation steps

1. Run the installation file.

Double-click to make the Welcome dialog box appear, and click Next.

2. Select the components to be installed.


Version: B 2-3

In this case, you need to install the dynamic database and the Client-SDK, so select IBM Informix Dynamic Server 11.50 with J/Foundation and IBM Informix Client-SDK 3.50 and click Next.

3. Confirm to install the Informix dynamic database.

Click Next to confirm the installation operation.

4. Accept the software agreement.


2-4 Version: B

Select I accept the terms in the license agreement, and then click Next.

5. Select the installation mode.

The operator must install the software in Custom mode, so please select Custom and then click Next.


Version: B 2-5

6. Set the installation path.

Here we take the installation on disk C as an example. In this case, set the installation path as C:\Informix; you also can install the database on other disks. Then click Next.

7. Select the database properties to be installed.

According to the default setting, you should install all properties by clicking Next.


2-6 Version: B

8. Set the database information.

1) Set the database user information according to Table 2-1, and then click Next.

Table 2-1 The database user information

Parameter Item Recommended Value Install Domain(requires Informix user) Clear Start database server as Local System User Clear Do not create user Informix account Clear Password Anms2k Confirm Password Anms2k Enable Role Separation for auditing procedures Clear

Note: You can set the database user password on demand. Such password must be formed by uppercase letters, lowercase letters and numbers.


Version: B 2-7

2) Set the database parameters according to Table 2-2, and then click Next.

Table 2-2 The database parameters

Parameter Item Recommended Value

Server Name

Commonly its value is the computer name along with the prefixed ol_, and we recommend that you modify it to the project name (such as ol_zjyd). In this manual, we take ol_test as an example for the description.

Create Server Select Initialize Server Clear Enable a custom configuration file to suit your needs and hardware Clear

Enable DRDA Support Clear Service Name turbo Port 6000 Server number 0

Caution: The internal database service name and port No. of the ANM2000 are respectively turbo and 6000; please set them correctly, otherwise the ANM2000 cannot be used correctly.


2-8 Version: B

Note: If turbo and 6000 are occupied, you can open the services file under C:\\ windows \ system32 \ drivers \ etc to delete the corresponding item. As Figure 2-1 shows, you need to delete the man 6000/tcp item.

Figure 2-1 The status that the port 6000 is occupied

3) Set the data store location information according to Table 2-3, and then click Next.

Table 2-3 The store location information

Parameter Item Recommended Value

Location for IDS data dbspace

DB Space Name It should be the same as the set Server Name. Primary Data Location D Mirror Data Location(optional) Null

Size (MB) 200

Location for smart large object data

SB Space Name sbspace Primary Data Location D Mirror Data Location(optional) Null

Size(MB) 200 Page Size (in pages) 1


Version: B 2-9

9. Confirm the settings and start the installation.

After confirming that the settings are correct, click Next to start installing the Informix database.


2-10 Version: B

10. Complete the installation.

After completing the installation, click Finish to start installing the Informix Client-SDK.

In this case, the installation of the Informix database is completed.


Version: B 2-11

2.2 Installation of the Informix Client-SDK

The Informix Client-SDK is used to establish the connection from the client end to

the database server. After the Informix database is installed, the system will

automatically enter the installation programme of the Informix Client-SDK.

Prerequisites

The Informix database has been installed.

Operation steps

1. Confirm the installation.

After the database is installed, click Finish to make the IBM Informix Client-SDK 3.50 Setup dialog box appear. In this dialog box, click Next to confirm to install the Informix Client-SDK.


2-12 Version: B


In the License Agreement dialog box, select I accept the terms in the license agreement, and then click Next.

3. Set the personal information.

Set your personal information, and then click Next.


Version: B 2-13

4. Select the installation type.

For the installation type, you must select Custom, and then click Next.


Click Change to set the installation path of the Client-SDK, which should be identical with that of the Informix database, and then click Next.


2-14 Version: B

6. Select the components to be installed.

It is recommended to use the default settings; then click Next.

7. Install the Client-SDK.

1) Click Install to start installing the Client-SDK.


Version: B 2-15

2) Click Next.

3) Clear Launch VSAI Installer, and then click Finish to complete the installation.

In this case, the installation of the Informix Client-SDK is completed.


2-16 Version: B

2.3 Setting of the Environment Variables After installing the Informix database, you need to set the relevant variables, so as to use the Informix database normally.

Prerequisites

The Informix database and the Informix Client-SDK have been installed.

Operation steps

1. Set the environment variables.

1) Select Start All Programme IBM Informix Client-SDK 3.50 setnet32 to open the Informix setnet32 dialog box.

2) In the Informix setnet32 dialog box, select the Server Information tab (as shown in Figure 2-2); then click Make Default Server and click Apply to make the configuration valid.

If the server is configured with dual NIC, HostName should be set to the IP address to be bound with the database.

Figure 2-2 The Server Information tab


Version: B 2-17

3) Select the Host Information tab, and set the user password of the Informix; this password should be the same as the password set for the installation of the Informix database, such as Anms2k, as shown in Figure 2-3. Then click Apply.

Figure 2-3 Setting the Informix user password

Note: If you do not select Server Information but select Host Information directlythe Current Host item will be empty. In this case, you can select the Server Information tab first and the Host Information tab second, and then the Current Host item will read the default values automatically.

4) Click OK to open the IBM Informix Setnet dialog box, and then click OK.


2-18 Version: B

5) Select the Environment tab. In this tab, select the INFORMIXDIR= item, and set it to C:\Informix, as shown in Figure 2-4.

Figure 2-4 Setting the INFORMIXDIR

After completing the settings, select Use my settings, and then click Set and then Apply to make the configurations valid.


Version: B 2-19

6) Select the INFORMIXSERVER= item, and set it to the default value in the drop-down list of the Edit Environment Variable combo box, as shown in Figure 2-5.

Figure 2-5 Setting the INFORMIXSERVER

After completing the settings, select Use my settings, and then click Set and then Apply to make the configurations valid. Then click OK.


2-20 Version: B

7) Right-click Computer, and select Properties; in the System window, select Advanced System Settings; and in the System Properties dialog box, select Advanced.


Version: B 2-21

8) Click Environment Variables. In the System Variables pane of the Environment Variables dialog box, click Create to create INFORMIXDIR and INFORMIXSERVER; the values of the two items should be the same as those in the Informix setnet32 dialog box, as shown in Figure 2-6 and Figure 2-7.

Figure 2-6 Creating system variables (1)

Figure 2-7 Creating system variables (2)


2-22 Version: B

9) Click OK to finish the setting, as shown in the following figure.


Version: B 2-23

2. Modify the configuration file.

Use the notebook to open the etc \ ONCONFIG. Instance name file under the Informix installation directory (such as the ONCONFIG.ol_test file), and modify the ROOTSIZE value to 1024000 (see Figure 2-8) and the LOGFILES value to 40 (see Figure 2-9). After the modification is completed, save the configuration file and then exit.

Figure 2-8 Modifying the ROOTSIZE

Figure 2-9 Modifying the LOGFILES


2-24 Version: B

3. Start the service.

1) Right-click Computer, and select Manage to open the Server Manager window; in this window, select Configuration -> Services.

2) Double-click the Informix IDS service, and input iy in Start Parameter; then click Start.

After the start operation, please confirm that the service has been started.


Version: B 2-25

2.4 Verifying the Informix Database Installation

Prerequisites

The Informix database has been installed.

The Informix-IDS service has been started.

Operation steps

You can judge whether the Informix database can be used normally via the following steps.

1. Select Start All Progamme IBM Informix Dynamic Server 11.50 ol_test to open the ol_test window.

2. Input onstat -. If the system displays On Line, this indicates that the database has been started normally.

Figure 2-10 The status of the normal starting of the database


2-26 Version: B

3. Input onstat -l. If the system displays 40 total, this indicates that the modified configuration file has been valid.

Figure 2-11 The valid status of the configuration file

If the configuration file is not valid, please conduct the operations mentioned in Section 5.1.

Version: B 3-1

3 Installation of the ANM2000

The ANM2000 is an integrated broadband access management platform developed by FiberHome, which can perform the effective and unified management of multiple types of broadband access equipment developed by FiberHome. This chapter introduces the installation methods of the ANM2000.


Installation of the Server end Installation of the Client end


3-2 Version: B

3.1 Installation of the Server End

The server communicates with the managed system, collects various data of the system, and saves them in the database. In the installation of the server end, the client end can be installed automatically, and you do not need to install the client end again.

3.1.1 Running the ANM2000_Server Installation Package

Prerequisites

The Informix database and the Informix Client-SDK have been installed successfully.

Operation steps


Double-click to make the Welcome dialog box appear, and then click Next.


Version: B 3-3


Select Yes to accept the ANM2000 software agreement.


Set your personal information; for the Company Name item, please adopt the default value FiberHome. Then click Next.


3-4 Version: B

4. Select the installation language.

Select English by default, and then click Next.

5. Set the database information.

By default the database name is andb@ instance name (it should be the instance name of the installed Informix database; here andb@ol_test is used), and IP address is the IP address bound with the database. Then click Next.


Version: B 3-5

In the dual-NIC mode, please refer to Section 5.7 for determining the IP address bound with the database.

6. Input the username and the password.

Input the username and the password set in the installation of the Informix database (refer to Section 2.1), and then click Next.

7. Select the services to be installed.

It is recommended to select Anserver, Manager, ANCollection, and ANDumper by default. Then click Next.


3-6 Version: B


It is recommended to set the installation path as D:\AEMS. Then click Next.

9. In the ANM2000 InstallShield Wizard dialog box that appears, a promotion will appear to ask the operator to restart the computer after the completion of the installation. In this case, select Yes, I want to restart my computer now to restart the computer.


Version: B 3-7

3.1.2 Creating the Tablespace

Prerequisites

Before creating the tablespace, you need to stop the AEMS-CollectionServer, AEMS-DBServer, AEMS-DumpServer, AEMS-Manager, and AEMS-Daemon services.

Operation steps

1. Select Start All Programme IBM Informix Dynamic Server 11.50 ol_test.

2. Input one of the following commands:

C: \ Informix>d:

D: \ >cd aems / server / andb

D: \ AEMS \ Server \ andb \ createspaces s t|-m|-l

Among them:

-s: the singledisk, indicating that the generated space files are saved in one disk.

-t: the small size mode; in this mode, the harddisk space of 5 G is needed, and the ANM2000 can manage 100 OLTs.

-m: the medium size mode; in this mode, the harddisk space of 15 G is needed, and the ANM2000 can manage 200 OLTs.

-l: the large size mode; in this mode, the harddisk space of 73 G is needed, and the ANM2000 can manage 500 OLTs.

In the actual applications, the operator generally uses the medium size mode.

Note 1: The path inputted in the command is the default installation path, so you need to modify the path here based on the actual installation path.

Note 2: Please select one from the t|-m|-l in the command based on the network size. Do not input all of them (t|-m|-l) in a command.


3-8 Version: B

Figure 3-1 Creating the tablespace

If the system displays the following information, this indicates that the tablespace has been created successfully.

Figure 3-2 The status of the successful creation of the tablespace

If you fail to create the tablespace, please conduct the operations mentioned in Section 5.6.


Version: B 3-9

3.1.3 Initializing the Table Architecture

After the tablespace is created successfully, input createandb.

Figure 3-3 Initializing the Table architecture

If the system displays the information as shown in Figure 3-4, this indicates that the tablespace architecture has been initialized successfully.

Figure 3-4 The status of the successful initialization of the Table architecture


3-10 Version: B

3.1.4 Starting the Service

1. Right-click Computer, and select Manage to open the Server Manager window; in this window, select Configuration -> Services.

2. Select the AEMS-DBServer service, and click .

Use the same method to start the AEMS-Manager, AEMS-DumpServer, and AEMS-CollectionServer services.

3.1.5 Verifying the ANM2000s Server End Installation

1. Double-click to start the ANM2000.

2. Input the username and the password of the ANM2000, and the IP address of server to be logged in. By default the username and the password are both 1. Then click OK.


Version: B 3-11

Note: You may click the button, input the IP address in the Server IP

Management dialog box and click OK, so as not to input the IP address each time that you log in the server with the same IP address.

If you can log in the ANM2000 successfully, this indicates that the installation is successful.

3.2 Installation of the Client End

The client end is a work station. In this mode, the system displays the status of the managed system via the GUI, and you can query the performances status of the managed system and handle the relevant alarms via the client end.

3.2.1 Running the ANM2000_Client Installation Package

Prerequisites

There is an ANM2000 server which has been installed successfully.

The computer that carries the Client end can communicate with the ANM2000 server normally.

Operation steps


Double-click to make the Welcome dialog box appear, and then

click Next.


3-12 Version: B


Select Yes to accept the ANM2000 software agreement.


Version: B 3-13


Set your personal information; for the Company Name item, please adopt the default value FiberHome. Then click Next.

4. Select the installation language.

Select English by default, and then click Next.


3-14 Version: B


It is recommended to set the installation path as D:\AEMS_Client. Then click Next.

6. Complete the installation.

In the ANM2000 InstallShield Wizard dialog box that appears, a promotion will appear to ask the operator to complete the installation. In this case, select Yes, I want to restart my computer now to restart the computer. Then click Finish.


Version: B 3-15

3.2.2 Verifying the ANM2000s Client End Installation


2. Input the username and the password of the ANM2000, and the IP address of server to be logged in. By default the username and the password are both 1. Then click OK.

If you can log in the ANM2000 successfully, this indicates that the installation is successful.

Version: B 4-1

4 Upgrade of the ANM2000

When you want to obtain the newly-added functions of the new version or correct the faults of the current version, you need to upgrade the ANM2000. This chapter describes the upgrade flow of the ANM2000 from the following three aspects: the preparation before the upgrade operation, the upgrade operation, and the confirmation after the upgrade operation.


The upgrade of the Server end The upgrade of the Client end


4-2 Version: B

4.1 The Upgrade of the Server End

When you want to obtain the newly-added functions of the new version or fix the bug of the current version, you need to upgrade the ANM2000s Server end. The flow of upgrading the Server end is illustrated in Figure 1-3; and the detailed procedure of the upgrade is as follows:

4.1.1 Preparation before the Upgrade Operation

The upgrade conditions:

The computer to be the ANM2000s Server end has been installed with the legal Windows XP professional SP2, Windows2003, or Windows2008 standard operating system, the Informix database, and relevant patches and tools.

The operator has the basic operation knowledge of the legal Windows XP professional SP2 or Windows2008 standard operating system and the ANM2000.

Confirm the version Nos. of the currently used and the upgrade ANM2000s.

The installation package of the new version has been prepared; the Informix11.5 database is used together with the ANM2000 with the Build05.07.05.02 version, so please confirm that your installation package is of the Build05.07.05.02 version.

4.1.2 Backup of the Original Configuration Files

Operation purpose

To avoid the data loss caused by the upgrade, please back up the original configuration files before the upgrade operation.

Operation steps



Version: B 4-3

2. Select System Export Config to set the path of the backup file, and then click OK.

When the following alert box appears, this indicates that the data are backed up successfully.

4.1.3 Backup of the Software Package

To avoid the modification of the installation package caused by the upgrade failure, please back up the software package of the new version and the current version, so as to perform the upgrade again.

Operation step

1. Save a copy of the ANM2000_Server file with the new version and the current version respectively.

Note: If there is not the ANM2000_Server file with the current version, you can back up the installation directory of the current AEMS.


4-4 Version: B

4.1.4 Uninstalling the Current ANM2000

After completing the backup before the upgrade, you can uninstall the current ANM2000 according to the following steps.

Prerequisites

Before uninstalling the current ANM2000, you need to stop the AEMS-CollectionServer, AEMS-DBServer, AEMS-DumpServer, AEMS-Manager, and AEMS-Daemon services.

Operation steps

Method 1:

1. Select Start Control Panel to open the Control Panel window.

2. Double-click Add or Delete Programme to open the Add or Delete Programme window.

3. Select ANM2000, and then click Delete.

Method 2:

Double-click to make the Confirm Uninstall dialog box appear, and then click OK to uninstall the original ANM2000.

Then the Maintenance Complete dialog box will appear to give a prompt that the original ANM2000 has been uninstalled. In this case, click Finish.


Version: B 4-5

4.1.5 Installing the ANM2000 of the Upgrade Version

The operations are the same as those of the installation of the Server end. For the detailed operations, refer to Section 3.1.

Caution: After running the upgraded ANM2000_Server installation package, please conduct the creation of Tablespace and the initialization of the Table architecture.


4-6 Version: B

4.1.6 Importing the Configuration Data

Operation purpose

After the ANM2000 is upgraded, the database will be cleared. In this case, you need to import the backup configuration data to the network management system.

Operation steps


2. Click in the toolbar to make the system enter the edit mode.

3. Select System Import Config, and the system will give a prompt that the imported data may overwrite the current data; click Yes to confirm to continue the operations.

4. Select the path of the backup file, and then click OK. When the alert box as follows appears, this indicates the data have been imported successfully; in this case, click OK to restart the ANM2000 GUI.


Version: B 4-7

4.1.7 Verifying the Upgraded Software Version

Operation purpose

After completing the upgrade, you need to check whether the upgraded software version is what you want.

Operation steps

Start the ANM2000, and select Help About Anms in the main menu. In the About Anms alert box, click About Anms to view the version information. If the current version is the upgraded version, this indicates that the software version is correct.


4-8 Version: B

4.1.8 Checking the Configuration Data

Operation purpose

After verifying the upgraded software version, you need to check whether the upgraded configuration data are identical to those before the upgrade.

Operation steps

Start the ANM2000, and the Topology tab will display the configuration data before the upgrade. View whether the systems and modules in each management domain can be displayed and operated on the GUI; if so, this indicates the configuration data are correct.


Version: B 4-9

4.2 The Upgrade of the Client End

After completing the upgrade of the Server end, you need to upgrade the Client end too. The flow of upgrading the Client end is illustrated in Figure 1-4; and the detailed procedure of the upgrade is as follows:

4.2.1 Preparation before the Upgrade Operation

The upgrade conditions:

The computer to be as the ANM2000s Client end has been installed with the legal Windows XP, Windows2003, Windows2008, Windows Vista or Windows7 operating system.

The version No. of the new ANM2000 to be installed has been confirmed.

The installation package of the new version has been prepared.

4.2.2 Uninstalling the Current Client end

Uninstall the current Client end according to the following steps.

Double-click to make the Confirm Uninstall dialog box appear, and

then click OK to uninstall the original ANM2000.


4-10 Version: B

Then the Maintenance Complete dialog box will appear to give a prompt that the original ANM2000 has been uninstalled. In this case, click Finish.


Version: B 4-11

4.2.3 Installing the Client End with the Upgrade Version

The operations are the same as those of the installation of the Client end. For the detailed operations, refer to Section 3.2.

4.2.4 Verifying the Upgraded Software Version

Operation purpose

After completing the upgrade, you need to check whether the upgraded software version is what you want.

Operation steps

Start the ANM2000, and select Help About Anms in the main menu. In the About Anms alert box, click About Anms to view the version information. If the current version is the upgraded version, this indicates that the software version is correct.

Version: B 5-1

5 FAQs

This chapter introduces the solutions to common problems in the installation of the Informix11.5 and the ANM2000.


How to handle the invalid configuration file How to handle the long-period no response from the ANM2000 How to handle the inadequate disk space How to handle the Informix database not installed How to handle the connection failure of the ANM2000 How to handle the tablespace creation failure How to determine the IP address bound with the database How to handle the data exporting / importing failure


5-2 Version: B

5.1 How to Handle the Invalid Configuration File

Question

The etc\ONCONFIG. instance name file under the Informix installation directory has been modified, but the configuration file is still invalid. How to handle this problem?

Answer

The probable reason of this is described as follows:

The system only uploads the ONCONFIG. instance name file during the

initialization operation. You can click to start the Informix IDS service

normally, but in this case, the ONCONFIG. instance name file cannot be uploaded.

The correct start method is described as follows: Double-click the Informix IDS service, input iy in the start parameter item, and then click Start.

5 FAQs

Version: B 5-3


5-4 Version: B

5.2 How to Handle the Long-Period No Response from the ANM2000

Question

During the network management operation, the ANM2000 does not respond in a long period. How to handle this problem?

Answer

The probable reason of the long-period no response from the ANM2000 is that the Informix service stops after it is started. The configuration parameters of the database can influence certain resources of the database; if the configuration parameters of the database have errors, certain resources may be inadequate, and this can lead to the condition that the service cannot be started normally.

Use the notebook or the UE to open the onconfig.ol_test file under C: \informix\etc, and check various configuration items in this file according to Table 5-1.

Table 5-1 Parameter values in the ONCONFIG file

Parameter Item Recommended Value ROOTSIZE 1024000 PHYSFILE 50000 LOGFILES 40 LOGSIZE 10000 SHMVIRSIZE 32656 SHMADD 8192 EXTSHMADD 8192

After the configuration is checked and confirmed to be correct, double-click the Informix IDS service, input iy in the start parameter item, and then click Start.

5 FAQs

Version: B 5-5

5.3 How to Handle the Inadequate Disk Space

Question

When the operator tries to create the database tablespace, the system gives a prompt that the disk space is inadequate. How to handle this problem?

Answer

After the installation of the ANM2000, you can execute the following command to create the small-size / medium-size / large-size tablespace respectively. The created tablespace occupies the disk space of 5 G, 15 G, and 73 G respectively.

D:\AEMS\Server\andb\createspaces s t|-m|-l

You should select to create the suitable tablespace on demand according to Table 5-2.

Table 5-2 The parameters for creating the tablespace

Parameter Value Size Mode Needed Harddisk Space Management Capacity -t Small 5 G 100 OLTs -m Medium 15 G 200 OLTs -l Large 73 G 500 OLTs

When the disk space is inadequate, you can select to create a relatively smaller database tablespace, or replace the harddisk.


5-6 Version: B

5.4 How to Handle the Informix Database Not Installed

Question

When the operator tries to install the ANM2000, the system gives a prompt that the Informix database is not installed. How to handle this problem?

Answer

You need to install the Informix database before installing the ANM2000. For the detailed operation steps, please refer to Chapter 2 Installation of the Informix Database.

5.5 How to Handle the Connection Failure of the ANM2000

Question

When the operator tries to start the ANM2000, the system gives a prompt as shown in the following figure. How to handle this problem?

Answer

You can handle this problem as follows:

5 FAQs

Version: B 5-7

1. Select Start All Programme IBM Informix Dynamic Server 11.50 ol_test, and then input onstat to check whether the database is started normally.

If the system displays On-Line, this indicates that the database is started normally. If the database is not started normally, please check whether the onconfig.ol_test file under C:\informix\etc is configured correctly according to Table 5-1.

2. Check whether the md.ini file under D:\AEMS\Server \ ini is configured correctly.

Check whether the parameter values of DATABASE_SERVER, LOGIN_USER, LOGIN_PASSWORD, and IP are correct.


5-8 Version: B

3. Confirm that the server IP address input via the Client end is correct.

After confirming the correctness of the previous information, restart the AEMS-CollectionServer, AEMS-DBServer, AEMS-DumpServer, and AEMS-Manager services.

5.6 How to Handle the Tablespace Creation Failure

Question

When trying to install the ANM2000, the operator fails to create the tablespace. How to handle this problem?

Answer

This problem is probably be caused by the authorization limit. You can log in ol_test as an Informix user, and then create the tablespace again.

1. Select Start All Programme IBM Informix Dynamic Server 11.50 ol_test, and then right-click ol_test to select Run Mode.

2. In the Run Identify dialog box, select Following User; set the username to Informix and the password to Anms2k, and then click OK.

3. Referring to Section 3.1.2, create the tablespace again.

5 FAQs

Version: B 5-9

5.7 How to Determine the IP Address Bound with the Database

Question

When the server is configured as the dual NIC mode, how to determine the IP address bound with the database?

Answer

You can handle this problem as follows:

1. Right-click Network, select Properties to open the Network and Sharing Center window.

2. Select Manage Network Connections to open the Network Connections dialog box.

3. Select Advanced Advanced Settings to open the Advanced Settings dialog box.

4. In the Adapters and Bindings tab, the NIC IP address with the highest priority in the Connections combo box is the NIC IP address bound with the database.


5-10 Version: B

5.8 How to Handle the Data Exporting / Importing Failure

Question

When needing to export / import the configuration data file (such as for the upgrade of the ANM2000), how to handle the data exporting / importing failure?

Answer

When exporting / importing the configuration data file, the ANM2000 needs to use a temporary tablespace; if the tablespace in the database is inadequate, the data exporting / importing failure may occur.

If the ANM2000 version has been modified, the format of the configuration data may also change; in this case, you need to convert the data format.

When one of the previous conditions occurs, please contact the engineers of FiberHome for handling it.

Product Documentation Customer Satisfaction Survey Thank you for reading and using the product documentation provided by FiberHome. Please take a moment to complete this survey. Your answers will help us to improve the documentation and better suit your needs. Your responses will be confidential and given serious consideration. The personal information requested is used for no other purposes than to respond to your feedback.

Name

Phone Number

Email Address

Company

To help us better understand your needs, please focus your answers on a single documentation or a complete documentation set.

Documentation Name

Code and Version

Usage of the product documentation:

1. How often do you use the documentation?

Frequently Rarely Never Other (please specify)

2. When do you use the documentation?

in starting up a project in installing the product in daily maintenance in troubleshooting Other (please specify)

3. What is the percentage of the operations on the product for which you can get instruction from the documentation?

100% 80% 50% 0% Other (please specify)

4. Are you satisfied with the promptness with which we update the documentation?

Satisfied Unsatisfied (your advice)

5. Which documentation form do you prefer?

Print edition Electronic edition Other (please specify)

Quality of the product documentation:

1. Is the information organized and presented clearly?

Very Somewhat Not at all (your advice)

2. How do you like the language style of the documentation?

Good Normal Poor (please specify)

3. Are any contents in the documentation inconsistent with the product?

4. Is the information complete in the documentation?

Yes

No (please specify)

5. Are the product working principles and the relevant technologies covered in the documentationsufficient for you to get known and use the product?

Yes

No (please specify)

6. Can you successfully implement a task following the operation steps given in the documentation?

Yes (please give an example)

No (please specify the reason)

7. Which parts of the documentation are you satisfied with?

8. Which parts of the documentation are you unsatisfied with? Why?

9. What is your opinion on the Figures in the documentation?

Beautiful Unbeautiful (your advice)

Practical Unpractical (your advice)

10. What is your opinion on the layout of the documentation?

Beautiful Unbeautiful (your advice)

11. Thinking of the documentations you have ever read offered by other companies, how would youcompare our documentation to them?

Product documentations from other companies:

Satisfied (please specify)

Unsatisfied (please specify)

12. Additional comments about our documentation or suggestions on how we can improve:

Thank you for your assistance. Please fax or send the completed survey to us at the contact informationincluded in the documentation. If you have any questions or concerns about this survey please email [email protected].

FiberHome Telecommunication Technologies Co., Ltd.

Address: No. 5 Dongxin Rd., Hongshan Dist., Wuhan, China

Zip code: 430073 Tel: +86-27-87691549 Fax: +86-27-87691755 Website: http://www.fiberhomegroup.com

Thank you for choosing our products.Legal NoticePrefaceContentsFiguresTablesOverviewWorking ModeConfiguration RequirementsRequirements of Hardware ConfigurationRequirements of Software Configuration

Installation Flow DiagramsInitial InstallationUpgrade

Installation of the Informix DatabaseInstallation of the Informix11.5 Dynamic DatabaseInstallation of the Informix Client-SDKSetting of the Environment VariablesVerifying the Informix Database Installation

Installation of the ANM2000Installation of the Server EndRunning the ANM2000_Server Installation PackageCreating the TablespaceInitializing the Table ArchitectureStarting the ServiceVerifying the ANM2000s Server End Installation

Installation of the Client EndRunning the ANM2000_Client Installation PackageVerifying the ANM2000s Client End Installation

Upgrade of the ANM2000The Upgrade of the Server EndPreparation before the Upgrade OperationBackup of the Original Configuration FilesBackup of the Software PackageUninstalling the Current ANM2000Installing the ANM2000 of the Upgrade VersionImporting the Configuration DataVerifying the Upgraded Software VersionChecking the Configuration Data

The Upgrade of the Client EndPreparation before the Upgrade OperationUninstalling the Current Client endInstalling the Client End with the Upgrade VersionVerifying the Upgraded Software Version

FAQsHow to Handle the Invalid Configuration FileHow to Handle the Long-Period No Response from the ANM2000How to Handle the Inadequate Disk SpaceHow to Handle the Informix Database Not InstalledHow to Handle the Connection Failure of the ANM2000How to Handle the Tablespace Creation FailureHow to Determine the IP Address Bound with the DatabaseHow to Handle the Data Exporting / Importing Failure

Documents

ANM2000 Installation Guide Version B