Embed Size (px)
Citation preview
1 Fire alarm [BSC ID No 65384]
2 Door Open alarm [BSC ID No 65385]
3 High temperature alarm [BSC ID No 65386]
4 Spare [BSC ID No 65387]
5 AC Removal alarm [BSC ID No 65388]
6 Genset run [BSC ID No 65389]
7 Genset failure [BSC ID No 65390]
8 Genset low fuel [BSC ID No 65391]
9 Phase R failure alarm [BSC ID No 65392]
10 Phase S failure alarm [BSC ID No 65393]
11 Phase T Failure alarm [BSC ID No 65394]
12 Arrester Failure alarm [BSC ID No 65395]
13 Rectifier Module alarm [BSC ID No 65396]
14 Rectifier High voltage alarm [BSC ID No 65397]
15 Rectifier Low voltage alarm [BSC ID No 65398]
16 OBL Failure alarm [BSC ID No 65399]
Cable connection in UEIU and UPEU : 1. FAN connected to UPEU_Mount_12. EAC BOX Huawei connected to UEIU_Mount_1
1、BTS ATP Alarm Test Item
2、Existing Alarm Box
3、DDF for Alarm cable
(1) Six ports for Boolean signal output
(3) Port for door status sensors
(5) Port for humidity/temperature sensors
(7) Four ports for analog signal sensors(9) Active/standby power port(11) Grounding screw
4、Huawei EAC
5、Front panel of Huawei EAC
6、Huawei Rectifier
Dry contact output port
Procedure of New Connection
Indoor Script BSC Script : (running 1 times only in each BSC)SET ENVALMPARA: AID=65033, ANM="GENSET LOW FUEL", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65034, ANM="GENSET FAILURE", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65035, ANM="GENSET RUN", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65036, ANM="AC REMOVAL ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65037, ANM="SPARE", ALVL=Major, ASS=env;
Connection Method:Press the white contact plates slightly using a flat-head screwdriver. Then, insert the two wires on the other end of the signal cable into the corresponding ports, and pull out the screwdriver to fasten the dry contact signal cable
7、Connection from Huawei EAC to Existing DDF
Step1:Disconnect the cable that connect to the existing alarm box on the left site of DDF1&2. Refer to the picture of DDF. Step2:Disconnect the cable that connect to the existing Ericsson rectifier on the both side .The port on the DDF site is 2/3/4/5/6/7/8.Step3:Connect the new cable that connect to the Huawei EAC on the left side of DDF1&2 follow above connection diagram.Step4:Connect the new cable that connect to the Huawei rectifier on the both side.Refer to the picture of Huawei Rectifier for rectifier site.The port on the DDF site is 2/4/5/6.
1 2 3 4 5 6 7 8 Huawei EAC
1 2 3 4 5 6 7 8 DDF1
Genset low fue
Genset failure
Genset run
AC Removal
Grouding Cut
Genset runHigh temperature alarmDoor Open alarm
Fire alarm
SET ENVALMPARA: AID=65038, ANM="HIGH TEMPERATURE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65039, ANM="DOOR OPEN ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65040, ANM="FIRE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65048, ANM="PHASE R FAILURE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65047, ANM="PHASE S FAILURE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65046, ANM="PHASE T FAILURE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65045, ANM="ARRESTER FAILURE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65044, ANM="RECTIFIER MODULE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65042, ANM="RECTIFIER LOW VOLTAGE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65043, ANM="RECTIFIER HIGH VOLTAGE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65041, ANM="OBL FAILURE ALARM", ALVL=Major, ASS=env;
SET BTSDEMUBP: IDTYPE=BYID, BTSID=xxx, CN=0, SRN=40, SN=0, CFGFLAG=YES, SBAF=WS_DISABLE-1&SS_DISABLE-1&IS_DISABLE-1&GS_DISABLE-1;
BSCTS01
Menghilangkan Burglar alarm di BTS IndoorSET BTSDEMUBP: IDTYPE=BYID, BTSID=18, CN=0, SRN=40, SN=0, CFGFLAG=YES, SAAF=48V_DISABLE-0&RES0-1&RES1-1&RES2-1&TS_DISABLE-0&HS_DISABLE-0&RES3-1&RES4-1, SBAF=WS_DISABLE-1&SS_DISABLE-1&IS_DISABLE-1&GS_DISABLE-1;
Setting Door High/LowSET BTSENVALMPORT: IDTYPE=BYID, BTSID=14, CN=0, SRN=40, SN=0, PN=6, SW=OPEN, AID=65039, PT=BOOL, AVOL=HIGH;
BTS Script : (modify BTS ID)SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=0,SW=OPEN,AID=65040, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=1,SW=OPEN,AID=65039, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=2,SW=OPEN,AID=65038, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=3,SW=OPEN,AID=65037, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=4,SW=OPEN,AID=65036, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=5,SW=OPEN,AID=65035, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=6,SW=OPEN,AID=65034, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=7,SW=OPEN,AID=65033, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=8,SW=OPEN,AID=65048, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=9,SW=OPEN,AID=65047, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=10,SW=OPEN,AID=65046, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=11,SW=OPEN,AID=65045, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=12,SW=OPEN,AID=65044, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=13,SW=OPEN,AID=65043, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=14,SW=OPEN,AID=65042, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=15,SW=OPEN,AID=65041, PT=BOOL,AVOL=HIGH;
BTS Script : (modify BTS ID)SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=0,SW=OPEN,AID=65033, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=1,SW=OPEN,AID=65034, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=2,SW=OPEN,AID=65035, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=3,SW=OPEN,AID=65036, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=4,SW=OPEN,AID=65037, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=5,SW=OPEN,AID=65038, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=6,SW=OPEN,AID=65039, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=7,SW=OPEN,AID=65040, PT=BOOL,AVOL=HIGH;
SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=8,SW=OPEN,AID=65048, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=9,SW=OPEN,AID=65047, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=10,SW=OPEN,AID=65046, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=11,SW=OPEN,AID=65045, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=12,SW=OPEN,AID=65044, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=13,SW=OPEN,AID=65043, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=14,SW=OPEN,AID=65042, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=15,SW=OPEN,AID=65041, PT=BOOL,AVOL=HIGH;
Huawei EAC at BSC Physical EAC port DDF Source Alarm Equipmentport 7 port 8 DDF1 port 8port 6 port 7 DDF1 port 7port 5 port 6 DDF1 port 6port 4 port 5 DDF1 port 5port 3 port 4 DDF1 port 4port 2 port 3 DDF1 port 3port 1 port 2 DDF1 port 2port 0 port 1 DDF1 port 1port 8 port 9 based on actual portport 9 port 10 based on actual port
port 10 port 11 based on actual portport 11 port 12 DDF2 port 5port 12 port 13 N/A ALM3 in Rectifierport 13 port 14 N/A ALM2 in Rectifierport 14 port 15 N/A ALM2 in Rectifierport 15 port 16 DDF2 port 1
(8) RS-232 port(10) Two RS-485 ports
(2) Port for water sensors
(4) Port for smoke sensors
(6) Port for infrared sensors
(12) Thirty-two ports for Boolean signal sensors
Item Connection TP48200A TP48200B
ALM1 Not Connect AC power failure AC power failure
ALM2 Connect DC under & over voltage
ALM3 Connect
ALM4 Not Connect SPD failure SPD failure
ALM5 Not Connect Fuse burn-out Fuse burn-out
ALM6 Not Connect BLVD alarm
SET ENVALMPARA: AID=65036, ANM="AC REMOVAL ALARM", ALVL=Critical, ASS=env;
DC under & over voltage
PSU faults PSU faults
temperature control unit
alarm
Press the white contact plates slightly using a flat-head screwdriver. Then, insert the two wires on the other end of the signal cable into the corresponding ports, and pull out the screwdriver to fasten the dry contact signal cable
Disconnect the cable that connect to the existing alarm box on the left site of DDF1&2. Refer to the picture of DDF. Disconnect the cable that connect to the existing Ericsson rectifier on the both side .The port on the DDF site is 2/3/4/5/6/7/8.Connect the new cable that connect to the Huawei EAC on the left side of DDF1&2 follow above connection diagram.Connect the new cable that connect to the Huawei rectifier on the both side.Refer to the picture of Huawei Rectifier for rectifier site.The port on the DDF site is 2/4/5/6.
1 2 3 4 5 6 7 8 Huawei EAC
1 2 3 4 5 6 7 8 DDF1
Genset low fue
Genset failure
Genset run
AC Removal
Grouding Cut
Genset runHigh temperature alarmDoor Open alarm
Fire alarm
9 10 12 13 14 Huawei EAC
1 2 4 5 6 DDF2
Precisson AC Failure
Rectifier Low&High voltage
Rectifier Module alarm
Arrester Failure
Phase R/S/T failure
Huawei Rectifier
SET ENVALMPARA: AID=65038, ANM="HIGH TEMPERATURE ALARM", ALVL=Major, ASS=env;
SET ENVALMPARA: AID=65048, ANM="PHASE R FAILURE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65047, ANM="PHASE S FAILURE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65046, ANM="PHASE T FAILURE ALARM", ALVL=Critical, ASS=env;SET ENVALMPARA: AID=65045, ANM="ARRESTER FAILURE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65044, ANM="RECTIFIER MODULE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65042, ANM="RECTIFIER LOW VOLTAGE ALARM", ALVL=Major, ASS=env;SET ENVALMPARA: AID=65043, ANM="RECTIFIER HIGH VOLTAGE ALARM", ALVL=Major, ASS=env;
SET BTSDEMUBP: IDTYPE=BYID, BTSID=xxx, CN=0, SRN=40, SN=0, CFGFLAG=YES, SBAF=WS_DISABLE-1&SS_DISABLE-1&IS_DISABLE-1&GS_DISABLE-1;
SET BTSDEMUBP: IDTYPE=BYID, BTSID=18, CN=0, SRN=40, SN=0, CFGFLAG=YES, SAAF=48V_DISABLE-0&RES0-1&RES1-1&RES2-1&TS_DISABLE-0&HS_DISABLE-0&RES3-1&RES4-1, SBAF=WS_DISABLE-1&SS_DISABLE-1&IS_DISABLE-1&GS_DISABLE-1;
SET BTSENVALMPORT: IDTYPE=BYID, BTSID=14, CN=0, SRN=40, SN=0, PN=6, SW=OPEN, AID=65039, PT=BOOL, AVOL=HIGH;
SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=0,SW=OPEN,AID=65040, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=1,SW=OPEN,AID=65039, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=2,SW=OPEN,AID=65038, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=3,SW=OPEN,AID=65037, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=4,SW=OPEN,AID=65036, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=5,SW=OPEN,AID=65035, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=6,SW=OPEN,AID=65034, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=7,SW=OPEN,AID=65033, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=8,SW=OPEN,AID=65048, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=9,SW=OPEN,AID=65047, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=10,SW=OPEN,AID=65046, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=11,SW=OPEN,AID=65045, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=12,SW=OPEN,AID=65044, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=13,SW=OPEN,AID=65043, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=14,SW=OPEN,AID=65042, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=15,SW=OPEN,AID=65041, PT=BOOL,AVOL=HIGH;
SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=0,SW=OPEN,AID=65033, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=1,SW=OPEN,AID=65034, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=2,SW=OPEN,AID=65035, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=3,SW=OPEN,AID=65036, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=4,SW=OPEN,AID=65037, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=5,SW=OPEN,AID=65038, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=6,SW=OPEN,AID=65039, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=7,SW=OPEN,AID=65040, PT=BOOL,AVOL=HIGH;
SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=8,SW=OPEN,AID=65048, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=9,SW=OPEN,AID=65047, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=10,SW=OPEN,AID=65046, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=11,SW=OPEN,AID=65045, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=12,SW=OPEN,AID=65044, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=13,SW=OPEN,AID=65043, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=14,SW=OPEN,AID=65042, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=91, CN=0, SRN=40, SN=0, PN=15,SW=OPEN,AID=65041, PT=BOOL,AVOL=HIGH;
Remark
existing alarm:Grounding Cut
existing alarm:Precisson AC Failure
Press the white contact plates slightly using a flat-head screwdriver. Then, insert the two wires on the other end of the signal cable into the corresponding ports, and pull out the screwdriver to fasten the dry contact signal cable
Connect the new cable that connect to the Huawei rectifier on the both side.Refer to the picture of Huawei Rectifier for rectifier site.The port on the DDF site is 2/4/5/6.
SET BTSDEMUBP: IDTYPE=BYID, BTSID=18, CN=0, SRN=40, SN=0, CFGFLAG=YES, SAAF=48V_DISABLE-0&RES0-1&RES1-1&RES2-1&TS_DISABLE-0&HS_DISABLE-0&RES3-1&RES4-1, SBAF=WS_DISABLE-1&SS_DISABLE-1&IS_DISABLE-1&GS_DISABLE-1;
Source Alarm Equipment1 Main Power Out of Range TPS482002 Burglar Alarm TPS482003 Burglar Alarm BTS
Cabble Connection : 1. Connect EAC cable (RJ45) from UEIU_Mount-1 and connect to TPS48200A_COM485/RS232 with LAN cable type.2. Conect FAN (top : above BBU) connected to UPEU_Mount_03. Connect FAN (bottom : above MRFU) connected to UPEU_Mount_1
BTS side :
BTS Script : Step1 During Configure BTS on CME Express, need to input TMC cabinet.Step2 ADD BTSCABINET: IDTYPE=BYID, BTSID=xxx, CN=2, SRANMODE=SUPPORT, TYPE=APM30, CABINETDESC="TPS48200A";Step3 ADD BTSBRD: IDTYPE=BYID, BTSID=xxx, CN=2, SRN=0, SN=0, BT=PMU;
Notice: BTS3900A use TMC cabinet
1、BTS ATP Alarm Test Item
step4 ADD BTSBRD: IDTYPE=BYID, BTSID=xxx, CN=0, SRN=8, SN=0, BT=TCU;step5 SET BTSDHEUBP: IDTYPE=BYID, BTSID=11, CN=0, SRN=8, SN=0, CFGFLAG=YES, MPN=0;
Author:if TCU cable connected to UEIU mount_0 still faulty, please check LST BTSDHEUBP first!!
RemarkAdding 1 subrack (APM30 : 2) on data configurationAdding 1 subrack (APM30 : 2) on data configurationNULL
1. Connect EAC cable (RJ45) from UEIU_Mount-1 and connect to TPS48200A_COM485/RS232 with LAN cable type.
TPS48200A Side :
During Configure BTS on CME Express, need to input TMC cabinet.ADD BTSCABINET: IDTYPE=BYID, BTSID=xxx, CN=2, SRANMODE=SUPPORT, TYPE=APM30, CABINETDESC="TPS48200A";ADD BTSBRD: IDTYPE=BYID, BTSID=xxx, CN=2, SRN=0, SN=0, BT=PMU;
ADD BTSBRD: IDTYPE=BYID, BTSID=xxx, CN=0, SRN=8, SN=0, BT=TCU;SET BTSDHEUBP: IDTYPE=BYID, BTSID=11, CN=0, SRN=8, SN=0, CFGFLAG=YES, MPN=0;
BTS Script : (modify BTS ID)SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=0,SW=OPEN,AID=65033, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=1,SW=OPEN,AID=65034, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=2,SW=OPEN,AID=65035, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=3,SW=OPEN,AID=65036, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=4,SW=OPEN,AID=65037, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=5,SW=OPEN,AID=65038, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=6,SW=OPEN,AID=65039, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=7,SW=OPEN,AID=65040, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=15,SW=OPEN,AID=65041, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=14,SW=OPEN,AID=65042, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=13,SW=OPEN,AID=65043, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=12,SW=OPEN,AID=65044, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=11,SW=OPEN,AID=65045, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=10,SW=OPEN,AID=65046, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=9,SW=OPEN,AID=65047, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=8,SW=OPEN,AID=65048, PT=BOOL,AVOL=HIGH;
SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=0,SW=OPEN,AID=65033, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=1,SW=OPEN,AID=65034, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=2,SW=OPEN,AID=65035, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=3,SW=OPEN,AID=65036, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=4,SW=OPEN,AID=65037, PT=BOOL,AVOL=HIGH; SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=5,SW=OPEN,AID=65038, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=6,SW=OPEN,AID=65039, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=7,SW=OPEN,AID=65040, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=15,SW=OPEN,AID=65041, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=14,SW=OPEN,AID=65042, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=13,SW=OPEN,AID=65043, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=12,SW=OPEN,AID=65044, PT=BOOL,AVOL=LOW;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=11,SW=OPEN,AID=65045, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=10,SW=OPEN,AID=65046, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=9,SW=OPEN,AID=65047, PT=BOOL,AVOL=HIGH;SET BTSENVALMPORT: IDTYPE=BYID, BTSID=13, CN=0, SRN=40, SN=0, PN=8,SW=OPEN,AID=65048, PT=BOOL,AVOL=HIGH;
