air compressors, air compressor parts and air powered accessoriesWood Industries, Inc., manufactures and distributes top of the line, high quality

to the north american industrial, contractor & home user markets.

www.eaglecompressor.com

iHts104L-aK

manufacturer ofthese quality brands

model #: ironHorse - iHts104L-aK

5.1cFm @

90psi

comes witH:

25’ air Hose

20 piece accessorY Kit

This rugged “twin stack” compressor with cast iron cylinder comes with a 4 gallon air tank capacity that provides 5.1 CFM @ 90 PSI. This units is oil lubricated for professional use and longer life and is powered by a thermally protected 1 HP, 115 volt electric motor which is CSA/US approved. Regulator, gauge and quick coupler connections round off this unit and

are very conveniently found and easy to access on the front mounted control panel.

tecHnicaL speciFications

Hp (running): 1.0 Hp motor rpm: 3450

cFm @ psi: 5.1 cFm @ 90 psi maX pressUre: 125 psi

receiVer: 4 gallon twin VoLtaGe: 115v

L-w-H (inches): 19-17-19 weiGHt (pounds): 77

more inFormation at: - www.eaglecompressor.com

TWIN STACK

Item Description Part Item Description Part1 Head Bolt M6x55 IH30551 38 Capacitor IH22502 Spring washer 6 IH1211 39 Washer 3 IH10393 Cylinder head IH1343 40 Spring washer 3 IH10404 Exhaust elbow IH1086 41 Bolt M3*6 IH10415 Head gasket IH1051 42 Shroud IH20246 Valve assembly 43 Bolt M5*15 IH17277 Valve seat/cyl gasket IH1053 44 Bolt M8*55 IH22118 Cylinder IH2034B 45 Washer 8 IH22129 Piston IH2038B 46 Nut 8 IH2213

10 Piston air ring IH2039M 47 Pressure switch 21UCBDB-CH11 Piston oil ring IH2039N 48 Connector IH000312 Piston pin clip IH1420B 49 Regulator R46-200-RNLA13 Piston pin IH1534B 50 Connector IH000414 Connecting rod IH1066B 51 Pressure gauge IH117715 Cyl/Crankcase gasket IH1225 52 Plug IH136016 Bolt M8*25 IH2035 53 Quick connect IH000117 Spring washer 8 IH1212 54 Strain relief IH220618 Crankshaft IH1068A 55 Power cord IH184119 Bolt M8*22-LH IH1802 56 Terminal (O)20 Crank case gasket IH2019 57 Terminal (Y)21 Crank case cover IH2021 58 Handle grip IH1527

21a Bolt M6*10 IH2207 59 Tank IH205022 Seal IH1591 60 Custion foot IH220023 Oil sight glass IH1519 61 Washer 6 IH220224 Bolt M6*18 IH0621 62 Bolt IH220325 Breather IH1071 63 Check valve IH2026A26 Crank case IH2020 64 Safety valve IH109027 Oil seal IH0530 65 Drain valve IH185028 Bearing IH0140 66 Tube IH130229 Rotator IH1919 67 Unloader tube w/fitting IH130230 Rear bearing IH0150 68 Air filter assembly IH107231 Stator IH1918A 69 Discharge tube w/fitting IH117032 Spring washer wave IH2209 71 Air filter assembly IH107233 Rear cap IH1046 72 Overload Protector IH200034 Spring washer 5 IH2210 6a Valve Plate ih106435 Bolt M5 IH1048 6b Reed Valve IH105236 Fan IH1044 6c Middle Valve Gst IH104937 Circlips IH1101

Air Compressor part breakdown sheet - IHTS104L

IHTS104L

Call 1-800-551-2406 for the Customer Service Department.

PortableElectric/GasCompressorOperating

Instructions

MODEL# SERIAL#

Carefully read this instruction manual before attempting to operate this compressor.

NOTICE

1-800-551-2406www.eaglecompressor.com

�

�

TABLE OF CONTENTSSafety Precautions

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ExtensionCords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

AirReceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

SafetyValve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation and Operating Instructions

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Break-InProcedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

BeforeOperatingtheAirCompressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

CompressorLubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FillingCompressorwithOil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

EngineLubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

OilChanges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

CheckingBeltTension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operating Your Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

EngineGasDriven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ElectricDrivewithDualControl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

ElectricDrive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Compressor Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Carefully read this instruction manual before attempting to

operate this compressor.

4

�

SAFETY PRECAUTIONS

Please familiarize yourself with the following information to prevent damage to your compressor unit and injury to the operator.

Theaircompressormotorand/orenginewillgethotwhileinoperation .Nevertouchthedischargetubing,engine,motororcompressorpumpwhileinoperation .

Thecompressoroperatesautomaticallywhilethepowerisconnectedandturnedon,ortheengineisrunning .

Compressedairfromtheunitmaycontainhazardousfumes .Airproducedbythiscompressorisnotsuitableforbreathingpurposes .Alwaysusearespiratorwhen

sprayingpaintorchemicals,orwhensandblasting .Alwayswearsafetyglassesorgoggleswhenusingcompressedair .

Itisnotpracticalorpossibletowarnyouaboutallthehazardsassociatedwithoperatingormaintainingthisequipment .Youmustuseyourowngoodjudgment .

ExTENSION CORdSTheuseofextensionscordsisnotrecommended .Plugdirectlyintoadedicatedcircuit .Iftheuseofanextensioncordisunavoidablethenmakesureyourextensioncordisingoodcondition .Whenusinganextensioncord,besuretouseoneheavyenoughtocarrythecurrentyourproductwilldraw .Anundersizedcordwillcauseadropinlinevoltageresultinginlossofpowerandoverheating .Table1showsthecorrectsizetousedependingoncordlengthandnameplateamperagerating .Ifindoubt,usethenextheaviergauge .Thesmallerthegaugenumber,theheavierthecord .

WARNING

CAUTION

Table 1 — Minimum Gauge for Cord

Volts TotallengthofcordinfeetAmpereRating120V 25ft . 50ft . 100ft . 150ft .

MoreThan AWG0

NotMoreThan

66

10

10

12

12

16

18 16 16 14

18 16 14 12

16 16 14 12

14 14 NotRecommended

AIR RECEIVEROverpressurizingtheairreceivercouldcausepersonalinjuryormaterialdamage .Toprotectfromoverpressurizing,afactorypre-setsafetyvalveis

5

�

Anyreplacementpartsshouldbepurchasedwiththesamespecificationsastheoriginalequipment .Pleasecontacttheauthorizeddealerforreplacementpartsorspecifications .

SAFETY VALVEThisvalveisfactoryinstalledtopreventoverpressurizingoftheairreceiver .Itisfactorysetataspecificlimitforyourparticularmodel,andshouldneverbetamperedwith .

Adjustment by user will automatically void the warranty.

INSTALLATION1. INSTALLATIONPropercare,maintenanceandlubricationensureslongevity .Thecompressorshouldalwaysbelevelforproperlubrication .Donotovertightenfootboltsasexcessivevibrationmayoccur .Useonlyinaclean,dry,andwell-ventilatedarea .Thecompressorhasheatdissipationfinsforpropercooling .Keepthefinsandotherpartsthatcollectdustclean .Donotplaceragsorothermaterialsontopofthecompressor,asthisobstructscoolingandcanbeafirehazard .

2. BREAK-IN PROCEdURE

Thereisnobreak-inrequirementsforthismodel

Never Weld, drIll Or ChANge

The AIr reCeIver IN ANY WAY.WARNING

dO NOT reMOve, MAke

AdjuSTMeNTS TO Or

SubSTITuTe ThIS vAlve!

WARNING

6

�

3. BEFORE OPERATING THE AIR COMPRESSOR, PLEASE CHECK THE FOLLOWING CAREFULLY:1 . Checktoseethatnutsandboltsareallsnug .2 . Checkifthequantityandqualityofoiliscorrect .3 . Iftheintakefiltersaredirty,theyshouldbereplacedorcleaned .

4. COMPRESSOR LUBRICATION

Recommended Oil: Eagle Compressor Oil #EAOIL10 (1 litre) #EAOIL40 (4 litres)

Eaglecompressoroilisanon-detergentmineraloilformulatedwithadditivestohelpminimizecarbonbuild-up,increaseringlifeandreduceoilconsumption,foruseatambienttemperaturesof0°to30°C(32°F-86°F) .

Other Approved Oils:RegularmineraloilscanalsobeusedinEaglecompressors .Alwaysuseanon-detergentoilwiththefollowingspecifications:

AlWAYS CheCk The OIl level ANd QuAlITY

beFOre STArT–uP. dO NOT Add Or ChANge

OIl WhIle The uNIT IS ruNNINg. uSe ONlY

reCOMMeNded NON-deTergeNT OIl.

WARNING

AMBIENT TEMPERATURES AT POINT OF OPERATION

SAE VISCOSITY ISO VISCOSITY

-16°CTO0°C(3 .2°F-32°F) SAE10W ISO32

1°CTO26°C(33 .8°F-78 .8°F) SAE20W ISO68

ABOVE27°C(80 .6°F) SAE30W ISO100

�

�

5. FILLING COMPRESSOR WITH OIL1 . Removetheoilfillerplug2 . Slowlypourtheproperoilintothepumpcrankcase .3 . Alwayskeepoillevelinthemiddleofthesightglass .

6. ENGINE LUBRICATION (IF ENGINE dRIVEN)CheckengineOwner'smanualforlubricationandmaintenance

requirements .

7. OIL CHANGESINITIAL OIL CHANGE DUE AT 100 HOURS

CHANGE OIL EVERY 300 HOURS OR 3 MONTHS, WHICHEVER COMES FIRST.1 .Removetheoildrainplug .Allowoiltodraincompletely .2 .Replacetheoildrainplug .3 .Refillwiththerecommendedoiltotheproperlevel .

8. MAINTENANCEBeforedoinganymaintenanceoradjustmentstoyouraircompressor,thefollowingsafetyprecautionsshouldbetaken: * TURN OFF AND UNPLUG POWER CORD. * DRAIN AIR RECEIVER AND AIR LINES OF AIR PRESSURE.

9. CHECKING BELT TENSION (If Belt driven)Adjustbelt(s)sowhenpressureisappliedatthecenter,thereisapproximately1/2"slack(seediagrambelow) .

Ifthebeltisinstalledtootight,themotormightbeoverloaded .Thiswillcausethemotortooverheat .Ifthebeltisinstalledtooloosely,itwillslipandexcessivewearandvibrationwilloccur .

Centre

Too Loose

Too Tight

Slight BowCorrect Tension

8

�

HOW TO INSTALL NEW BELT IF REQUIRED (If belt driven) 1 .Disconnectpowersupply . 2 .Removebeltguard . 3 . Loosenmotorboltsandslidemotortowardcompressorheadjust enoughtoallowoldbelttoberemoved . 4 .Installproperreplacementbelt . 5 . Slidemotorawayfromcompressorheadtoproviderecommended tensionasshownindiagramonpage5 . 6 . Alignbeltusingastraightedgeruleragainstpulley’sedge . 7 . Fastenmotorbolts . 8 . Ensuremotorandcompressorpulley’saresecure .Re-checkalignment .9 . Re-installbeltguardandreconnectpowersupply . 10 .Belttensionshouldbecheckedafter20hoursofoperation .Check tensionmonthlythereafter .

OPERATING YOUR AIR COMPRESSORA) GAS ENGINE dRIVEN (continous run only) 1)Checkentireunitforanydamage . 2)Checkcompressorandengineoillevel,filloraddifnecessary . 3)Makesuregastankisfilled . 4)Readentireenginemanual . 5)Startingtheengine . a) Movefuellevertothe"On"position . -Ifengineiscold,movechokelevertothe"Closed"position -Ifengineiswarm,leavechokeleverin"Open"position b) Turnengineswitchto"On"position . c) Pullstartergriplightlyuntilyoufeelresistance,thenpullbriskly, returnstartergripgently-engineshouldstart,ifnotrepeat . d) Oncetheenginestartsrunning,slowlymovethechokelever tothe"Open"position . e) Withtheenginerunningproperly,thecompressorfillstheair receiverwithcompressedair,whenmaximumpressure(setbythe pilotvalvecontrol)isreached,theengineandcompressorwillslow downtoidlespeed,andwillreturntofullRPMwhenthecut-in pressureisreached .Theunitwillcontinuetocycleautomatically untilturnedoff . 6)Stoppingtheengine . a) Turnengineswitchtothe"Off"position . b) Turnthefuellevertothe"Off"position .

eNgINe Idle SPeed MAY Need TObe AdjuSTed, eveN ON YOur brANd NeW uNIT TO

COMPeNSATe FOr dIFFereNCeS IN AlTITude. PleASe CONSulT The eNgINe OPerATINg MANuAl.

WARNING

�

�

B) ELECTRIC dRIVE WITH dUAL CONTROL 1)Checkunitforanydamage . 2)Checkcompressoroillevel,filloraddifnecessary . 3)Pressureswitch"Off/Auto"knobshouldbein"Off"position . 4)Pluginpowercordtoproperelectricaloutlet . 5 a) Stop/Start(pressureswitch)control 1 . Shut-offvalveonpilotunloadershouldbeclosed("knurled" knobontopofthepilotunloadershouldbeturnedalltheway down) . 2 . Turnpressureswitch"Off/Auto"switchto"Auto" .Electric motorshouldnowstartandfillairreceiver(s)withcompressed airtillcut-outpressureisreached .Compressorshouldstop andremainstoppedtillairreceiverpressurereachesthecut-in pressure .Theunitwillcontinuetocycleinthisautomatic operationuntilitisturnedoff . b) Continuousrun(Pilotunloader)control 1 . Opentheshut-offvalveonpilotunloader("knurled"knobon topofthepilotunloadershouldbeturnedallthewayup) . 2 . Turnpressureswitch"Off/Auto"switchto"Auto",electricmotor shouldnowstartandfillairreceiver(s)withcompressedairtill fullpressureisreached .Toengagecontinousrun,turn“knurled knobdown .Yourcompressorwillidledownandcontinueto idleoncemaximumpressureisacheived .Whencut-inpressure isreached,theunloadervalveswillde-activateandunitwill compressair .Theunitwillcontinueinthisautomaticoperation untiltheunitisstopped("Off/Auto"switchturntothe"Off" positionand/orelectricpowersupplyisdisconnected) . 3 . Withtheenginerunningproperly,thecompressorfillstheair receiverwithcompressedair,whenmaximumpressure(set bythepilotvalvecontrol)isreached,theengineand compressorwillslowdowntoidlespeed,andwillreturnto fullRPMwhenthecut-inpressureisreached .Theunitwill continuetocycleautomaticallyuntilturnedoff . 4 . Stoppingtheengine . a) Turnengineswitchtothe"Off"position . b) Turnthefuellevertothe"Off"position . 6)YoucanswitchatanytimefromStop/StarttoContinuousRunand viceversabyopeningorclosingthevalveonthepilotunloader .

C) ELECTRIC dRIVE 1)Checkunitforanydamage . 2)Checkcompressoroillevel,filloraddifnecessary . 3)Pressureswitch"Off/Auto"switchshouldbein"Off"position . 4)Pluginpowercordtoproperelectricaloutlet .Ifcompressoris notequippedwithamaleplug,hireanelectriciantoinstallone .

10

�

5)Stop/Start(pressureswitch)control Turnpressureswitch"Off/Auto"switchto"Auto" .Electricmotor shouldnowstartandfillairreceiver(s)withcompressedairuntilcut- outpressureisreached .Compressorshouldstopandremainstopped untilairreceiverpressurereachesthecut-inpressure .Theunitwill continuetocycleinthisautomaticoperationuntilthepressureswitch isturnedtothe"Off"position .

COMPRESSOR MAINTENANCE SCHEdULEdAILY OR BEFORE EACH USE• Checkoillevel

• Draincondensationfromairreceiver

• Checkforanyunusualnoiseorvibration

• Besureallnutsandboltsaretight

WEEKLY• Turnoffpower .Cleandustandforeignmatterfromcylinderhead,motor,

fanblades,intercoolerandairreceiver .

• Cleanairfilterbyopeningairfilter,removingfilterelementandcleaningitthoroughlywithsoapywater .Rinsethoroughlyandallowtodrycompletelybeforeassembly .

• Wornfiltersshouldbereplaced .

• CheckV-beltsforwear .

MONTHLY• Inspectunitforleaks .

• Tightenjointsifleaksareobserved .

• CheckV-beltsforpropertension .

• Checkcompressorpulleyandmotorsheavearealignedandsecurelyfastened(seeitem9) .

QUARTERLY OR 300 HOURS (Whichever comes first)• Inspecttheairreceiverforcorrosionorotherdamage

• Changecompressoroil .

•Replaceairfilter(moreoftenifcompressorisusednearpaint sprayingoperationsorindustyenvironments) .

exTrA CAre ShOuld be TAkeN TO AvOId

PerSONAl INjurIeS WITh AuTOMATICAllY

CONTrOlled COMPreSSOrS

WARNING

11

�

Will Not Start

Low Pressure

Oil In discharge

CompressorOverheats

Compressor Loads and Unloads or Stops and Starts Excessively

• Checkpowersupply

• PleaserefertoManufacturersmanualincluded

• Safetyvalveleaks• Draincockopen• Loosetubesorfittings• Dirtyorpluggedairfilter

• Defectiveunloadervalve

• Improperoilviscosity• Toomuchoilinthecrankcase• Compressoroverheated

• Restrictedairfilter• Wornpistonrings

• Cloggedinletfilter

• Dirtycompressor,head,cylinder,intercooler

• Operatingpressuretoohigh• Lowoilorwrongoilbeing

used• Compressorcycletoolong,

propercycleis50-60%onStop/Startoperationand75-80%oncontinuousrunoperation

• Leaksinairsystem

• Wornorloosedrivebelts• Pilotvalveorpressureswitch

differentialadjustedtooclose

• Defectivecompressorvalves• Compressortoosmallfor

intendeduse

• Makesurepoweristurnedon

• PleaserefertoHondamanualincluded

• Replacesafetyvalve• Closedraincock• Tightenfittings• Cleanorreplaceas

necessary• Replaceunloadervalve

• Drainandreplaceoil• Drainoilandfilltoproper

level• Airpressureregulatedtoo

high• Cleanorreplaceairfilter• Replacepistonrings

• Cleanorreplaceasnecessary

• Cleanwithcompressedair

• Reduceoperatingpressure• Drainandreplaceoil

• Allowforlongerrestbetweencycles

• Replaceworncomponentsasnecessary

• TightenV-beltsorreplace• Makenecessary

adjustments

• Replacevalves

TROUBLE SHOOTINGPROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

12

�

Insufficient Output Low discharge Pressure

Motor Stalls

Water In Crankcase Oil Break-ing Up Oil Gets dirty, Rusty Valves or Cylinder

• Cloggedinletfilter

• Leaksinairlines,airvalves,fittingsetc, . .

• Drivebeltsslipping• Drainvalveleftopen• Defectivepressuregauge• Compressorincorrectlysized• Leakingheadgasket• Dirtyorpluggedintercooler

tubes• Unloaderpilotorpressure

switchadjustedtoolow,ordefective

• Wornordefectivecompressorvalves

• Wornpiston,wornoutrings• Restrictivecheckvalve

• Faultyunloader/checkvalve

• Valvesincorrectlyinstalled• Drivebeltstootight

• Cycletooshort;compressordoesnotoperatelongenoughtovaporizecondensedmoistureduringcompression

• Compressoroperatingoutsideincoldconditionsorinletfilternotprotectedagainstweather

• Systempressureleakingbackthroughcheckvalvewhencompressorisstopped

• Wrongoilbeingused

• Cleanorreplaceasnecessary

• Replaceworncomponentsasnecessary

• TensionV-Belts• Closedrainvalve• Replacepressuregauge

• Replaceheadgasket• Removeandcleaninter

coolertubes• Makenecessary

adjustments

• Replacewornparts

• Replacewornparts• Cleancheckvalveand

replaceifnecessary

• Replaceunloaderorcheckvalve

• Installvalvescorrectly• TensionV-belts

• Allowforalongeroperatingcycle

• Provideadequateprotectionagainstextremeweatherconditions

• Checkandreplace/checkvalveifnecessary

• Drainandreplacewithproperoil

TROUBLE SHOOTINGPROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

1�

�

Excessive Vibration

Compressor Knocks

Compressor uses too much oil

Piston rings not seated

• Loosecompressor,motor,engineorguard

• Excessivedischargepressure• Compressornotlevel• Legboltstightenedtoo

tightlytofloor• Wrongoilbeingused

• Looseflywheel,drivepulleyordrivebelts

• Wornrods,wristpinormainbearings

• Compressorvalveslooseorbroken

• Inspectcheckvalve,itmayknockatlowpressures

• Cloggedinletfilter

• Wrongoilbeingused,wrongviscosity

• Oilleveltoohigh

• Crankcasebreathervalvemalfunction

• Compressorrunsunloadedtoolong

• Compressoroperatingoutsideincoldconditionsorinletfilternotprotectedagainstweather

• Wornpistonrings• Pistonringsnotseated

• Allow100hoursofnormaloperationfornewringstoseat

• DrainoilandrefillwithPaslodeEAOILoilorotherapprovedoils

• Tightencomponents

• Reduceoperatingpressure• Levelcompressor• Loosenlegbolts

• Drainandreplacewithproperoil

• Tightenloosecomponentsandcheckbelts

• Checkandreplacewornparts

• Checkandreplacewornorbrokenvalves

• Removeandcleancheckvalve

• Cleaninletfilterorreplaceifnecessary

• Drainandreplaceoil

• Fillcompressorwithoiltoproperlevel

• Replacecrankcasebreather

• Increaseloadorstopcompressorwhennotneeded(checkforair/leaks)

• Provideadequateprotectionagainstextremeweatherconditions

• Replacepistonrings• Seeinstructionbelow

• Allow100hoursofnormaloperationfornewringstoseat

• DrainoilandrefillwithPaslodeEAOILoilorotherapprovedoils

TROUBLE SHOOTINGPROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

14

�

�WOOD INDUSTRIES STANDARD�WARRANTY

Seller warrants products of its own manufacture against defects in workmanship and mate-rials under normal use and service as follows:

COMPRESSORS: Twelve (12) months from date of start-up or

PARTS: Ninety (90) days from date of sale

WII warrants repaired or replaced parts of its own manufacture against defects in materi-als and workmanship under normal use and service for ninety (90) days or the remainder of the warranty on the product being repaired, whichever is longer.

With respect to products not manufactured by WII, WII will, if practical, pass along the warranty of the original manufacturer.

Notice of the alleged defect must be given to Seller in writing with all identifying details in-cluding serial number, model number, type of equipment and date of purchase, within thirty (30) days of the discovery of same during the warranty period.

Eagle’s sole obligation on this warranty shall be, at its option, to repair, replace or refund the purchase price of any product or part thereof, which proves to be defective, F.O.B. Eagle shop.

If requested by WII , such product or part thereof must be promptly returned to WII, freight prepaid for inspection.

This warranty shall not apply and WII shall not be responsible nor liable for:

a) Consequential, collateral or special losses or damages; b) Equipment conditions caused by normal wear and tear, abnormal conditions of use, accident, neglect or misuse of equipment, improper storage or damages resulting during shipment; c) Deviation from operating instructions, specification or other special terms of sale; d) Labor charges, loss or damage resulting from improper operation, maintenance or repairs made by person(s) other than WII or WII authorized service representative; e) Improper application of product.

In no event shall WII be liable for any claims, whether arising from breach of contract or warranty of claims of negligence or negligent manufacture, in excess of purchase price.

THIS�WARRANTY�IS�THE�SOLE�WARRANTY�OF�WII�AND�ANY�OTHER�WARRANTIES,�EXPRESSED,�IMPLIED�IN�LAW�OR�IMPLIED�IN�FACT,�IN-CLUDING�ANY�WARRANTIES�OF�MERCHANTABILITY�AND�FITNESS�FOR�PARTICULAR�USE,�ARE�HEREBY�SPECIFICALLY�EXCLUDED.

15

�

1-800-551-2406www.eaglecompressor.com

NOTES

Compresseur portatif

électrique/à essence

Manuel d’utilisation

MODEL# SERIAL#

Veuillez lire le présent manuel d’utilisation avant d’essayer d’utiliser ce compresseur.

AVIS