MODEL T250S-F1616 Gauge Straight

Finish Nailer

IMPORTANT!DO NOT DESTROY

It is the customer’s responsibility to have alloperators and service personnel read andunderstand this manual.

OPERATING MANUAL ANDTOOL SCHEMATIC

PP

TOOL WARRANTY AND LIMITATIONS

2

INTRODUCTION

The PASLODE® T250S-F16 finish nailer is a quality-built tool designed for use in residentialtrim applications. This tool will deliver efficient, dependable performance when used accordingto the manufactures guidelines. Please study this manual including the safety instructions tofully understand the operation of this tool.

TOOL AND FASTENER SPECIFICATIONS ....................................................... 3 SAFETY INSTRUCTIONS ...................................................................................4 TOOL OPERATION .............................................................................................. 5 EXPLODED VIEW AND SPARE PARTS LIST .............................................10-11 ACCESSORIES ..................................................................................................12

TOOL SPECIFICATIONS

MODEL NO. T250S-F16 (Part# 501680)

HEIGHT 11.3"

WIDTH 3.1"

LENGTH 11.5"

WEIGHT 3.9lbs.

OPERATING PRESSURE 80 to 120 p.s.i. (5.5 to 8.3 bars)

ASSEMBLY HARDWARE SYSTEM Metric

FASTENER SPECIFICATIONS

TOOL AIR FITTINGS:This tool uses a 1/4” N.P.T. male plug. The inside diameter should be .28” (7mm)or larger. The fitting must be capable of discharging tool air pressure whendisconnected from the air supply.

OPERATING AIR PRESSURE:80 to 120 p.s.i. (5.5 to 8.3 bars). Select the operating air pressure within this rangefor best tool performance.DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.

NAIL LENGTH 3/4" - 2-1/2"

SHANK DIAMETER 16 gauge

TOOL AND FASTENER SPECIFICATIONS

3

WARNINGFailure to follow any of the above instructions could result in severe personalinjury to tool user and bystanders or cause damage to tool and property.

Contact your local Paslode Representative for presentation of Paslode’s Safety Awareness Program

4

SAFETY INSTRUCTIONS

SAFETY FIRSTThese safety instructions provide information necessaryfor safe operation of Paslode® tools. DO NOT ATTEMPTTO OPERATE THE TOOL UNTIL YOU READ ANDUNDERSTAND ALL SAFETY PRECAUTIONS ANDMANUAL INSTRUCTIONS.

WEAR EYE AND HEARING PROTECTIONAlways wear hearing and eye protection devices, thatconform to ANZI Z87.1 requirements, when operating orworking in the vicinity of a tool. As an employer you areresponsible for enforcing the use of eye protection.Wear hard hats in environments that require their use.

THE TOOL MUST BE USED ONLY FOR THE PUR-POSE FOR WHICH IT WAS DESIGNEDDo not throw the tool on the floor, strike the housing inany way or use the tool as a hammer to knockmaterial into place.

NEVER ENGAGE IN HORSEPLAY WITH THE TOOLThe tool is not a toy so do not use it like one. Neverengage in horseplay with the tool or point it at yourselfor any other person, even if you think it is not loaded.

NEVER ASSUME THE TOOL IS EMPTYCheck the magazine for fasteners that may be left in thetool. Even if you think the tool is empty or disconnected,never point it at anyone or yourself. Unseen fastenerscould fire from the tool.

NEVER CLAMP THE TRIGGER IN A LOCKED OROPERATING POSITIONThe trigger of the tool must never be tampered with,disabled or clamped in a locked or operating positionsince this will cause the tool to drive a fastener any timethe work contacting element depressed.

DO NOT LOAD FASTENERS WITH THE AIR LINECONNECTED, OR WITH THE TOOL TRIGGER ORWORK CONTACTING ELEMENT DEPRESSEDWhen loading fasteners into the tool be sure youdisconnect the air line and that you do not depress thetrigger or work contacting element.

OPERATE THE TOOL ONLY ON A WORKPIECEThe tool should be operated only when it is in contactwith the workpiece. Even then you should be carefulwhen fastening thin material or working near the edgesand corners of the workpiece since the fasteners maydrive through or away from the workpiece.

DO NOT DISABLE OR REMOVE THE WORK CON-TACTING ELEMENTThis tool is equipped with a safety mechanism, called awork contacting element, to help preventaccidental firing. Never tamper with, disable or removethe work contacting element. Do not use the tool unlessthe work contacting element is working properly. Thetool could fire unexpectedly.

DISCONNECT THE TOOL WHEN NOT IN USEAlways disconnect the tool from the air line when it isnot in use, when you leave the work area or whenmoving the tool to a new location. The tool mustnever be left unattended because people who are notfamiliar with the tool might handle it and injurethemselves or others.

CARRY THE TOOL ONLY BY THE HANDLEAlways carry the tool by the handle only. Never carrythe tool by the air hose or with the trigger depressedsince you could drive a fastener unintentionally andinjure yourself or someone else.

DO NOT WEAKEN THE TOOL HOUSINGThe tool housing is a pressure vessel and should neverbe weakened by having your company’s name, areaof work or anything else stamped or engraved into itssurface.

DISCONNECT THE TOOL WHEN PERFORMINGREPAIRS AND CLEARING JAMSNever attempt to clear a jam or repair a tool unless youhave disconnected the tool from the air line andremoved all remaining fasteners from the tool.

ALWAYS USE THE PROPER FITTING FOR THETOOLOnly MALE pneumatic type air connectors should befitted to the tool, so that high pressure air in the tool isvented to atmosphere as soon as the air line isdisconnected.NEVER install FEMALE quick disconnect couplings onthe tool. Female couplings will trap high pressure airin the tool when the air line is disconnected, leavingthe tool charged and able to drive at least one fastener.

DO NOT EXCEED THE MAXIMUM RECOMMENDEDAIR PRESSUREOperate the tool only at the recommended air pres-sure. Do not exceed the maximum air pressure markedon the tool. Be sure the air pressure gauge isoperating properly and check it at least twice a day.

Never use any bottled air or gases such as oxygen tooperate the tool since they could cause the tool toexplode.

INSPECT TOOL FOR PROPER OPERATIONClean the tool at least daily and lubricate as required.Never operate a dirty or malfunctioning tool.

USE ONLY PASLODE RECOMMENDED PARTS ANDFASTENERSUse only parts and fasteners specifically designed andrecommended by Paslode for use in the tool and forwork to be done. Using unauthorized parts andfasteners or modifying the tool in any way createsdangerous situations. Replace all missing warninglabels---refer to tool schematic for correct placementand part number.

FastenersThe Paslode T250S-F16 Finish Nailer drivesPaslode® 16 gauge fasteners designed to be usedwith the tool. The use of fasteners that do not meetPaslode standards could cause tool damage and willvoid all warranty claims.

Loading FastenersSTEP 1: Align the heads of the Paslode 16 ga.Finishnails to the brad channel in the rear of the magazineand insert one or two strips. Push the nails stripsforward.

STEP 2: Next, while applying pressure to the releaselever, pull the follower toward the rear of themagazine until the follower passes the last strip offasteners. Release the lever on the follower and letthe follower push the nails forward into the nose ofthe tool.

When the follower reaches the reload area, markedon the side of the magazine, you may insert a newstrip of nails. When the follower arrow reaches thelockout area the tool automatically locks the tool toprevent the tool from operating. To unlock the tool,simply reload another strip of nails.

Depth of Drive AdjustmentDisconnect the air supply.The depth of drive adjustment is done by turning theadjustment wheel as shown by the arrows on the side ofthe tool.

Clearing a JamAn occasional problem you may encounter is a jammedfastener. Because of the unique design of the PaslodeFinish Nailer, clearing a jammed fastener is easy:

1. Disconnect the air supply.2. Pull the latch, releasing front guide. Pivot front guide forward.3. Clear jam, and push driver blade back up to its normal position.4. Close front guide and latch it. Check that work contacting element moves freely.

TOOL OPERATION

5

Lockout FeatureThe purpose of this feature is to prevent needlessblank cycling, which could mar woods and dam-age tool components. Ten (10) nails will be left inthe magazine when the follower reaches thelockout area. When changing fastener length orloading at the beginning of the work day, youshould inspect the magazine and nose for anyfasteners left in the tool. These nails will not bevisible unless you open the nose of the tool.

Turnadjustmentwheel ineitherdirection

TOOL OPERATION

Trigger Methods:The Paslode T250S-F16 Finish Nailer has a triggeringsystem than can be switched from sequential to contacttrip. To switch the trigger, press in the round orangebutton on the right side of the trigger and rotate the leftside of the button to the desired triggering method. TheTTT indicates contact trip and the T indicates sequentialoperation.

Successive (Bounce) Driving -

Grasp the handle firmly.

Squeeze the trigger and move the tool along theworkpiece with a bouncing motion, depressing the workcontacting element at the points where you want to drivea fastener.

Keep the trigger depressed and continue to bounce thework contacing element against the workpiece, position-ing the tool above as carefully as possible.

When the desired number of fasteners have beendriven, release the tool trigger to avoid unintentionalfastener discharge.

6

Reversible Belt Hook:The belt hook can be changed from the left hand side ofthe tool to the right hand side. To change the position,squeeze the base of the belt hook and remove it from thetool and position it on the desired side.

Adjustable Exhaust:The direction of the exhaust air can be changed byrotating the orange air deflector on the cap of the tool.

Sequential Operation -The sequential setting T prevents succesive or "bounce"driving.

Depress the work contacting element and hold itagainst the work surface before pulling the trigger.

After each fastener is driven, completely release thetrigger and lift the tool from the work surface.

➔➔

➔ ➔

MAINTENANCE

Paslode® tools are built for ease of maintenance. A fewsimple details will assure trouble-free operation and longtool life. Anyone who uses or maintains the tool must readthe safety and maintenance instructions. Study the sche-matic drawing before starting any repairs on the tool.

Air-operated tools must be inspected periodically, and wornor broken parts must be replaced to keep the tool operatingsafely and efficiently. Also the items on the maintenancechart must be checked often.

Cold Weather Care

When temperatures are below freezing, tools should bekept warm by any convenient, safe method. If this is notpossible, the following procedure should be used to warmup the tools.

❑ Reduce the regulated air pressure to 30 psi.

❑ Remove all fasteners from the tool.

❑ Collect an air line and blank fire the tool. The reducedair pressure will be enough to free-fire the tool. Slow speedoperation tends to warm up the moving parts. Slowing upthe piston helps the bumper and the O-rings to becomepliable.

❑ Once the tool is warmed up, readjust the regulator tothe proper working pressure and reload the tool.

❑ Tool operators working outdoors or in unheated areas inextremely cold temperatures should also:

Use Paslode pneumatic oil with antifreeze in the lubricator, Part No. 219090 (8oz.)

Once a week, depending on the amount of tool use, take the tool apart and wash away any sludge with degreaser cleaner (Paslode Part No. 219086) to keep the tool operating efficiently.

Cleaning the air-operated tools with solvents removes thethin coating of grease applied to the cylinder wall andO-rings at the factory. To replace this coating of grease,use Chemplex grease (Paslode Part No. 403734).

❑ Open the drain on the air compressor tank to drain anymoisture at least daily in extremely cold or humid weather.A few ounces of anti-freeze in the tank will keep the airfree of frost.Testing the Tool After ServicingAfter replacing any part or parts, it is important to checkthe tool for proper operation. This ensures that the toolwas put together correctly, is safe to use, and will performthe job properly.

❑ Ensure that all hardware is tight.

❑ Ensure that the work contacting element is installedcorrectly in relation to the trigger, and that both partsmove freely.

❑ Ensure that the magazine is properly attached.

❑ Ensure that the required safety information on the toolis legible.

❑ Use only Paslode approved fasteners in the tool, andensure that they are correct for the application.

❑ Ensure that a male air fitting is securely connected tothe tool.

❑ Test the tool by driving fasteners into a workpieceidentical to the tool's application.

❑ Check the tool for air leaks during testing and for theproper sequence of operation.

❑ Ensure that all fasteners are driven to the same depthand that the crown of the fastener is flush with theworkpiece.Tool LubricationIt is most important that the tool be properly lubricated bykeeping the air line lubricator filled and correctly adjusted.Without proper lubrication the tool will not work properlyand parts will wear prematurely.

Use the proper lubricant in the air line lubricator. Thelubricator should be of low air flow or changing air flowtype, and should be kept filled to the correct level. Useonly Paslode recommended lubricants. Substitutes mayharm the rubber compounds in the tools O-rings and otherrubber parts. Paslode Part No. 403720 is a pneumaticlubricating oil specially made for pneumatic applications.

If a filter/regulator/lubricator is not installed on the airsystem, air operated tools should be lubricated at leastonce a day with 6 to 20 drops of oil, depending on thework environment, directly through the male fitting in thetool housing.Most minor problems can be resolved quickly and easilyusing the maintenance table that follows. If problemspersist, contact your Paslode dealer for assistance.

7

MAINTENANCE

Drain air line filter (daily).

Keep lubricator filled.

Clean filter element, then blowair through filter in directionopposite to normal flow.

Check that all screws on toolare tight.

Keep work contacting elelmentworking properly.

Keep magazine and feedermechanism clean.

Lubricate "O" rings that arereplaced.

Use only Paslode replacementparts.

ACTION WHY HOW

Prevent accumulation ofmoisture and dirt.

Keep tool lubricated.

Prevent clogging of filter withdirt.

Prevent air leakage and pro-mote efficient operation.

Promote operator safety andefficient tool operation.

Prevent jamming of fasteners.

Assure long life and properoperation of tool.

Keep tool operating efficientlyand maintain Paslode toolwarranty.

Open manual petcock (mostair supply systems have sucha valve).

Fill with Paslode pneumatictool lubricant. Part No.219026.

Wash with soap and water orfollow manufacturers instruc-tions.

Check screws daily.

Blow clean daily.

Blow clean daily.

Use Chemplex grease, PartNo. 403734.

Order any replacement partsneeded from Paslode Dealer.

8

OPERATOR TROUBLESHOOTING

PROBLEM CORRECTIVE ACTION

Fasteners will not drive completely into wood.

Fasteners penetrate properly during normaloperation, but won't drive fully at faster speeds.

Fasteners drive too deeply into wood.

Fastener jams in nose of tool.

Tool skips during operation - no fasteners are drivenfrom time to time.

Tool operates, but no fasteners are driven.

Air leaks at cap when tool is connected to air.

Adjust the depth of drive adjustment (retract length).

Increase air pressure (do not exceed 120 psi).

Increase air flow to tool -- use larger air lines(3/8 inch ID minimum).

Adjust the depth of drive adjustment (extend length).

Reduce air pressure.

Open front guide latch, release jammed fastener,and close latch securely.

Check magazine for proper fasteners. Magazinefollower should slide freely. Clean as needed toremove debris.

Make sure correct fasteners are being used.Use fasteners that meet Paslode® specifications only.

Increase air flow to tool -- use larger air lines(3/8 ID minimum).

Adjust work contacting element where available.

Check magazine for proper fasteners. Fastenersshould slide freely with no follower pressure.

Open front guide latch or loosen magazine knob andcheck for jams or debris in the nose area. Clear asnecessary.

Increase air pressure (do not exceed 120psi).

Tighten cap screws.

9

45 501092 1 Dust Cover46 501972 2 Bolt47 501091 1 Air Plug48 501939 1 Belt Hook49 501938 2 Hex S.H.C.S.50 501998 1 Spring Pin51 501931 1 Spring Pin52 501089 1 Urethane Retainer53 501963 1 Steel Channel54 501966 1 Safety B55 501967 1 Safety Spring56 501968 1 E-Ring57 501969 1 Adjust Shaft58 501387 1 Spring59 501970 1 Safety A60 501971 1 No Mar Tip61 501951 1 Latch Cover62 501950 2 Spiral Pin63 501949 1 Front Latch Handle64 501948 1 Front Latch65 501947 1 Driver Guide Cover66 501946 1 Spiral Pin67 501940 2 Hex Soc.Hd.Bolt68 501941 1 Driver Guide Cover B69 501942 1 Driver Guide70 501943 1 Stopper Finger Spring71 501944 1 Stopper72 501945 1 Fixed Pin73 501953 1 Pusher Spring74 501954 1 Pusher75 501955 1 Spring Pin76 501952 1 Anchor Block77 501956 1 Negator Spring78 501960 1 Magazine Steel Cover79 501961 1 Counter Sunk Screw80 501959 1 Tap Bolt81 501958 1 Protecting Hood Cover82 501962 1 Lock Nut83 501957 1 Magazine A84 501973 1 Nameplate85 501302 1 Warning Label86 501140 1 Housing Label-left87 501141 1 Housing Label-right88 501995 1 Tap Bolt

1 501885 1 T.H.S.C.S. 1/4-20 x 1/2 2 501896 1 Flat Washer 3 501899 1 Deflector 4 501901 1 Bolt 5 501902 1 Cap 6 501903 1 Seal 7 501904 1 Spring, Main Valve *8 501905 2 O-Ring 9 501906 1 Head Valve Piston10 501907 1 O-Ring11 501908 1 Collar12 501909 1 Packing13 501910 1 Piston Ring14 501911 1 O-Ring15 501912 1 Driver Blade16 501920 1 Cylinder Press Ring17 501913 1 O-Ring18 501914 1 Cylinder19 501915 1 Cylinder Ring20 501916 1 Cylinder Spacer21 501917 1 O-Ring22 501918 1 Bumper23 501919 1 Driver Guide24 501921 1 O-Ring25 501922 1 O-Ring26 501923 1 Plunger Cap27 501930 2 Spring Pin28 501924 1 Valve Plunger29 501925 2 O-Ring30 501926 1 O-Ring31 501927 1 Spring32 501928 1 Plunger33 500999 2 O-Ring34 501929 1 Trigger Valve Head35 501932 1 Spring36 501933 1 Trigger Unit37 501965 2 Tap Bolt38 501962 1 Lock Nut39 501964 1 Magazine B40 501961 1 Counter Sunk Screw41 501934 1 Trigger Pivot Pin42 501935 1 Housing43 501936 1 O-Ring44 501937 1 End Cap

PARTS LEGEND T250S-F16, 501680

* Denotes Normal Wear Items.** Make sure Warning Label (501302) is properly affixed. Replace if necessary. Label available at no charge through the Service Parts Dept.

DO NOT EXCEED MAXIMUM

RECOMMENDED AIR PRESSURE

60

0

120

60

0

120

Always wear hearing protection and eye protection devices,including side shields when operating or working in the vicinityof a tool.

Operate the tool using only the recommended air pressure. Donot exceed the maximum air pressure marked on the tool. Besure the air pressure gauge is operating properly and check itat least twice a day.

SAFETY INSTRUCTIONSWEAR EYE AND HEARING PROTECTION

10

Never use any bottled air or gases such asoxygen to operate the tool since they could causethe tool to explode.

*

****

*

**

**

*

**

T250S-F16501680

11

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

22

23

21

242526

27 2829

30

31

3233

34

35

36

37

38

37

39

40

41

42

4344

4546 47

46

48

49

50

5152

5354

55

56

57

58

59

60

6162

63

65

66

67

68

6970

71

75

74

72

76

77

78

79

80

81

82

83

64

73

Driver BladeAssembly#501987

TriggerValveAssembly#501988

87

86

84 85

WARNINGAll parts must be periodically inspected andreplaced if worn or broken. Failure to do this canaffect the tool’s operation and present a safetyhazard.

Assembly Hardware System - Metric

88

P

.Lubricants

027304 .oN traP.zo 61 liO gnitacirbuL 090912 .oN traP.zo 8 ezeerftinA htiw liO gniacirbuL 437304 .oN traP.bl1 tnacirbuL 017 xelpmehC

Tool Cleaner483912 .oN traP.sloot edolsaP lla rof renaelc laedI

Safety Glasses382104 .oN traPraelC

ACCESSORIES

An Illinois Tool Works Company888 Forest Edge DriveVernon Hills, Illinois 60061-8117

© 2010, Illinois Tool Works, Inc.501977-3

04/10

Tool CaseHandy carrying case that conveniently stores your tool

879105 .oN traP .seirossecca lanoitidda rof moor htiw