swingo 450B

0I1

9I1

8I1

7I1

6tr

svsl

ptpl

nonl

itfr

fies

ende

dacz

9-13

*

V

011

/ 120

89-1

3 10

11

I24

I23

I22

I21

I2

*120

8

I25

26

Translation of the original Instructions of Use

Symbols

Intended use of machinery

The TASKI swingo 450B are scrubber dryer machines that are designed for commercial use (for example, in hotels, schools, hospitals, factories, shopping centres, offices, etc.).Under strict observation of the instructions for use, they can be used for the wet cleaning of hard floor coverings.These machines are exclusively designed for indoor use only .

ContentSafety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Translation of the original EU Declaration of Conformity . . . . . . . . . 27Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Preparation for operation/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 28Beginning work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29End of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Service, maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Squeegee settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Malfunctions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Dimensions of the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Dimensions of the battery compartment. . . . . . . . . . . . . . . . . . . . . . . 33

Safety instructionsDue to their design and construction, TASKI machines comply with health and safety requirements of the EC guidelines and therefore carry the CE sign.

ATTENTION!Before first start-up, it is essential that you read the instructions of use and the safety notes carefully.Keep the instructions of use in an easily accessible place so that they can be consulted at any time.

Non-observance of this information can endanger people and / or cause servere damage!

Non-observance of this information can lead to malfunctions and property damage!

Important information about correct use. Non-observance of this information can lead to malfunctions!

Marks work steps that you must carry out in turn.

Caution:These machines may not be used for polishing, the application of wax, cleaning carpets or the vacuuming up of dust. The wet cleaning of parquet and laminate floors with this machine is carried out at your own risk.

Changes to the machines that have not been authorised by Diversey will lead to the cancellation of the Safety Marks and the CE conformity. Any use of the machines contrary to its intended purpose can lead to injuries to persons and damage to the machine and to the working environment.In such cases, any claims under the guarantee and warranty claims will normally become invalid.

Persons (including children) who are not able to use this machine safely due to their physical, sensory or mental capabilities or their lack of experience or knowledge may not operate this machine without supervision or instruction by a person responsible for their safety!Children should be supervised to ensure that they do not play with the appliance.

Do not use the machine is n rooms in which in explosive and eassily inflammable materials (e.g. petrol, solvents, fuel oil, dusts, etc.) are stored or processed. The electrical or mechanical components could lead to these materials being ignited.The machine must not be used in rooms with electromagnetic loading (elektrosmog).

STOPSTOP

•

STOPSTOP

STOPSTOP

STOPSTOP

Do not use this machine to vacuum toxic, poisonous, caustic or irritating substances (e.g. acids, alkalis, hazardous dusts, etc.). The filter system will not adequately retain these kinds of materials. A possible impairment of the health of the user and of third parties cannot be excluded.

While operating the machine, take note of the surrounding area and pay particular attention to third parties and children!In particular, the speed of the machine should be reduced in the vicinity of areas of unclear vision, for example, in front of doors or curves.

The machine may only be used by persons who have been suitably instructed in its use.

Neither persons or objects may be transported with the machine!

In case of damage to parts that could affect safety, such as the tool cover, power supply cord or covers that prevent access to current-carrying parts, the operation of the machine must be stopped immediately!

Regularly check the power supply cord for tearing or aging, and do not put the machine into operation if it is not in a safe and suitable condition!

Caution:Repairs to mechanical or electrical parts of the machine must only be undertaken by Diversey authorised customer service workshops or experts who are experienced in all relevant safety regulations.Minimum requirements on the H05VV-F2x1.5 or H05VV-F2x0.75 power cord.

Caution:The battery compartment must not be opened!

Caution:This machine is only intended for use in dry areas, and must not be used or stored in the open air or under damp conditions.

Caution:Pay attention to the accident prevention regulations!

Caution:Switch off the suction unit immediately if foam or liquid escape from the machine!See page 32 for further procedure .

Caution:Only use the tools that are defined in these Instructions for Use under Accessories or that have been recommended by the TASKI specialist (page 33), as other tools could impair the safety of the machine.

Caution:The protection of persons is based on the specific national regulations together with the information provided by the detergent manufacturer!

Caution:This machine may not be operated without batteries!

Caution:The batteries may only be operated with a battery charger that has been tested to the latest state-of-the-art according to EN 60335-2-29!(only model type:450.0)

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

STOPSTOP

27

I25

I24

I23

I22

I21

I20

I19

I18

I17

I16

trsv

slpt

plno

nlit

frfi

esen

deda

cz

Important! Switch the machine off when you:

• e.g. carry out cleaning or maintenance work, or convert the machine to another function

• store it in a suitable room to avoid any unauthorised use of the unit• leave it standing without supervisionTo do this, remove the keyswitch, pull out the battery disconnection socket and prevent the machine from rolling away (e.g. by placing a wedge under it).

Store the machine in a dry, dust-free room with a corrosion-free atmosphere.The temperature must not fall below +10 °C or exceed +35 °C. Low temperatures, damp and dust can significantly reduce the service life of the electrical components.

Translation of the original EU Declaration of ConformityWe hereby declare that the product described below conforms to the relevant safety and health-related requirements of the appropriate EU Directive, in both its design and construction, as well as in the version that we market.This declaration shall cease to be valid if modifications are made to the product without our approval.

Applicable EU Directives:

Directive 2006/42/EG of the European Parliament and of the Council dated 17th May 2006 regarding machinery and for the amendment of the Directive 95/16/EG (new version)Directive 2004/108/EG of the European Parliament and of the Council dated 15th December 2004 for the harmonisation of the legal regulations of the Member States regarding electro-magnetic compatibility and for the annulment of Directive 89/336/EWG

Harmonised standards applied:

EN 60 335-1-ed. 4.1+A1+A2/EN 60 335-2-67: 2009/EN 60 335-2-69: 2009/EN 50 366/EN 55 014-1-A1/EN 55 014-2-A1/EN 61 000-3-2+A2/EN 61 000-3-3+A1+A2Internal measures have been taken to ensure that the products always correspond to the requirements of the latest EU Regulations and the standards that are currently in use

The signatories act on behalf of company management and with full power of attorney.

Only use the machine on level floors or on gradients of 2% or less.This symbol on the machine indicates that it is not suitable for use on surfaces with greater gradients.

The tank cap must be closed when moving or driving the machine.

Noise emission and vibrations:TASKI machines and units have been designed so that any danger to health through the noise emitted or through vibrations can be excluded according to the current state of knowledge. Refer to the technical information on page 33.

2%

Designation: Automatic machine for the treatment of floors for commercial purposes

Product: scrubber dryerModel: swingo 450BModel: CO450.0 (24VDC/900W)

CO450.0X (24VDC/900W) (230-240VAC/50-60Hz/195W)

Serial number: Refer to the rating plate on the machine

Trade mark:

Manufacturer: Diversey, 9542 Münchwilen - Switzerland

Person authorised to compile the technical file:Stephan EnglerDiversey Europe B.V. UtrechtZweigniederlassung MünchwilenCH-9542 Münchwilen

Münchwilen, dated 01.03.2010

Dipl. Ing. (FH) D.Windmeisser Dipl. Ing. (FH) P. KönigTechnical Director Value Chain Director

Floor Care EquipmentFloor Care Equipment

28

Overview

1 Dosing cup2 Filling level (max.)3 Emptying hose for recovery tank (red cap)4 Drain opening5 Dirt sieve6 Recovery tank7 Recessed grip8 Brush unit9 Tools (brush, pad drive, etc.)10 Solution tank filter11 Manual solution flow adjustment12 Solution tank13 Emptying hose for solution tank (blue cap)14 Machine handle15 Operating lever (brush drive)16 Adjusting lever for the inclination of the machine handle17 Vacuum air filter18 Float (overfilling protection for recovery tank)

19 Hour counter (optional)20 Keyswitch21 Cable support for charging unit power cord22 Disconnector charger jack (coded)23 Suction unit height adjustment24 Squeegee support wheel height adjustment25 Squeegee lowering device26 Squeegee settings27 Squeegee28 Pedal brush unit (optional)29 Service indicator30 Fault in battery or internal charging unit31 Battery charging (Power plug connected)32 Battery fully charged33 Battery indicator34 Vacuum button35 Solution dosing control

Preparation for operation/Operation

Batteries

Safety measures when working with batteries:

Battery connection diagram

Charging procedure (traction block batteries with integrated charging unit)

2

8

9 10

5

11

612

7

13

15161718

14

1

3

4

19

20

21

22

23

24

25 26 27

28

35

max.60˚C

max.140˚F

max.60˚C

max.140˚F

max.60˚C

max.140˚F

29

30

31

32

3334

Caution:Only maintenence-free gel traction block batteries may be used!Please follow the instructions of use for your battery charger!

• Protective goggles must be worn when working on the batteries.

• Do not subject batteries to an open flame or heat as there is a danger of explosion from the electolytic gas present in the cells!

• No smoking!

• Danger of chemical burns!

Caution:The battery must always be clean and dry. Do not place any metallic objects on the battery.

The integrated charging unit is only suitable for maintenance-free gel traction block batteries.

Caution:Batteries may only be installed or dismounted by customer service personnel or specialists approved by Diversey who are aware of all the safety regulations that apply here!

• Check that the machine has been switched off with the keyswitch.• Disconnect the battery from the machine using the battery disconnection

socket.• Plug the power supply cord into the mains socket.

• The yellow indicator lights up permanently until approx. 90% of the battery capacity has been reached. After that, the indicator blinks until the battery is fully charged.

12V

24V

12V

75

A

29

I25

I24

I23

I22

I21

I20

I19

I18

I17

I16

trsv

slpt

plno

nlit

frfi

esen

deda

cz

After completing the charging and with immediate use:

Charging procedure (traction block batteries with external charging unit)

Attaching tools

Check: • that the brush has not fallen below the red mark or a brush length of 1 cm.• the pad for wear before using.

Attach squeegee

Filling water

Dosage:

Only use chemical products recommended by the manufacturer.

Dosing examples (The concentration is product dependent)

Beginning work

• When the charging process is complete, the green indicator lights up.

• Leave the power supply cord connected to the mains until you use the machine again. The on-board charger unit automatically monitors and charges the batteries. The energy consumption in the mode is limited to a few milliwatts.

• If a fault occurs during the charging process as the result of a defect in the charging unit, an interruption of a cable or a defective battery cell, the red indicator will light up.

• Unplug the connection to the mains socket.• Connect the battery to the machine with the battery disconnection socket.

• Check that the machine has been switched off with the keyswitch.• Disconnect the battery from the machine using the battery disconnection

socket.• Connect the battery disconnection socket to the external battery charging

unit (pay attention to the voltage from the mains supply socket).

Caution:Follow the instructions of use for your battery charger!

• Switch the machine off using the keyswitch and remove the key.

Working with worn out, damaged and or wrong tools, could result in possible damage to floors or their protective layers.

• Position the tool below the brush unit.• Switch on the keyswitch.

• Unlatch the foot lever and slowly lower the tool.

• Briefly pull the brush drive bar.By doing this the tool will be centered and coupled.

• Switch the machine off.• Raise the squeegee and loosen the fixing

screws on the squeegee.The squeegee support wheel must be in the direction of movement.

• Assemble the squeegee and tighten the fixation knobs.

• Attach the suction hose to the squeegee.

Caution:Maximum permissible water temperature 60 °C/140 °F.

• Switch the machine off.• Lift the tank lid.

• Fill water into the solution tank.Maximum permissible filling level (page 28).

Caution:Wear protective gloves, goggles and the corresponding (protective) work clothing when handling chemical products!

Caution:Using other chemicals (e.g. chemicals containing solvents, chlorine, hydrochloric acid and hydrofluoric acid) can damage or destroy the machine.

Instructions on the product’s packaging

Tank capacity The volume per tank filling

0.25% 25ml to 10l water 20l 50ml = 0,05l

0.5% 50ml to 10l water 20l 100ml = 0,1l

• Add the product measured with the dosing aid to the water in the solution tank.

Caution:Always wear non-slip shoes and appropriate work clothing while working with this machine!

• Lower the squeegee.

• Unlatch the foot lever and slowly lower the tool.

• Switch on the keyswitch.

• First press the solution dosing control button, and then the vacuum on.The indicators light up briefly.

• Adjust the volume of the cleaning solution.

• Pull the operating lever.By doing this the tool is activated.

max.60˚C

max.140˚F

30

Cleaning method

Direct method:Scrubbing and vacuuming in one pass.

Indirect working method:Apply the cleaning solution (only scrubbing), afterwards scrubbing and vacuuming.The cleaning methods are described in detail in the ”Method Card”. You can obtain this from your TASKI partner.

Refilling the solution tank

When the tools are no longer sufficiently supplied with the solution, the tank containing the solution is empty.

End of operation

Drain the recovery tank / solution tank

The disposal of the dirty water or the cleaning solution must be carried out in accordance with the appropriate national regulations.Proceed as follows for both tanks:

Clean the recovery tank / solution tank

Clean solution tank filter

Cleaning the tool

Removing and cleaning the squeegee

Under certain circumstances, the driving of the machine can be impaired by a special combination of surface/soiling and cleaning product.This effect can be reduced by special wheel options.

Caution:Do not clean without solution, as it could cause floor damage.

• Stop cleaning.• Refill the tank, see Page 29.

• Stop the flow of solution.

• Drive a few metres so that the tool rotates further for a short time. You will avoid dripping by doing this.Very important when using contact pads!

• Release the operating lever.• Press down the pedal and lock it in place to

raise the tool.

• Drive on a few metres further in order to pick up the remaining dirty water.• Raise the squeegee.

Allow the suction unit to continue running until the rest of the dirty water has been sucked into the hose.

• Switch off the suction unit first, and then the keyswitch.

Always drain and clean the recovery tank every time you use the machine.If the dirty water is allowed to stand, unpleasant smells and deposition of the dirt will take place after a few hours.

• Switch the machine off.• Remove the drainage hose from its holder.

Open the red or blue cap situated near the handle and lower the end of the hose slowly to drain the solution out.

• Switch the machine off.• Lift the tank lid.• Remove the coarse dirt sieve (yellow), empty and clean it.

• Remove the recovery tank and clean it and the hose with water.The tank can be completely drained via the drain opening.

• Replace the recovery tank on the machine.• Then thoroughly rinse out the solution tank with clean water.• Check the float is functioning correctly and that the suction filter (yellow) is

clean.In case of damage or soiling of the float and suction filter, please refer to page 31.

• After draining and cleaning, screw the red and blue caps on again, and hang the hoses from their holders again.

Caution:Clogged filters reduce the flow of the cleaning solution. As a consequence you may damage the floor coating.

• Switch the machine off.• Once the solution tank has been drained, screw

the yellow cap from the solution tank filter and pull it away from its holder.

• Rinse the filter under running water.If necessary, the filter should be descaled with a 10% TASKI calcacid solution.

The filter is lower than the tank outflow. A residual amount of solution will flow out once the filter cap has been unscrewed.

• Refit the solution filter.

• Switch the machine off using the keyswitch and remove the key.• Press down the pedal and lock it in place to

raise the tool.

• Turn the tool anticlockwise away from the tool coupling using your foot.

• Clean the tool with water.

• Switch the machine off.• Pull the suction hose away from the squeegee support.

• Raise the squeegee and loosen the fixing screws on the squeegee.The squeegee support wheel must be in the direction of movement.

• Remove the squeegee from the squeegee support.

• Clean the squeegee with water using a brush.

1

2

31

I25

I24

I23

I22

I21

I20

I19

I18

I17

I16

trsv

slpt

plno

nlit

frfi

esen

deda

cz

Cleaning the machine

Storage / parking of machine (machine is idle)

Store the machine with the tank cap slightly open, by:• lifting the tank cap, unscrewing the sieve, and placing it in the hollow

provided.• Then replace the tank cap on the sieve.

Service, maintenance and care

The correct maintenance of the machine is a precondition for error-free operation and a long service life.

Service intervals

TASKI machines are high quality machines that have been checked for safety at the factory by authorised inspectors. Electrical and mechanical components are subject to wear and/or ageing after longer periods of use.

Service centre

Should you contact us due to a malfunction or for placing an order, please always state the type, description and the serial number of your machine.You can find this information on the name plate of your machine, and the address of your nearest TASKI partner can be found on the last page of this manual.

Blades replacement

Blade on the inner radius.

Blade on the outer radius

Cleaning or replacing the float (Indication for full recovery tank)

Disassembly:

Optimal result can only be obtained with clean and intact blades!

Caution:Never clean the machine with high water pressure or a water hose.The ingress of water into the machine might cause considerable damage to mechanical or electrical parts.

• Wipe down the machine with a damp cloth.

We recommend that you disconnect the battery from the machine using the battery disconnection socket when storing / parking the machine and when charging the battery.

The sieve holds the tank lid slightly open, allowing the tank to dry out. As a result, the formation of mould and unpleasant smells can be reduced.

Caution:Only TASKI branded spare parts must be used, otherwise warranties and liabilities will be omitted!

Symbols:◊ = at the end of every cleaning operation, ◊◊ = every week, ◊◊◊ = every month, ⊗ = Service Light

Activity ◊ ◊◊ ◊◊◊ ⊗ page

Recharge batteries 28

Clean all parts marked yellow

Drain and clean the tanks 30

Clean the machine with a damp cloth 31

Clean the tank lid seal, check for cracks and re-place if necessary

Maintenance programs by TASKI service made by TASKI technician

• In order to maintain operational reliability and availability for use, the service must be carried out after 250 working hours (option: only with installed operating hours counter) or at least once a year.

Shorter intervals are necessary in case of rough environments or special conditions of use and/or inadequate maintenance.

• Place the clean squeegee unit with the outer radius face down on a solid surface e.g. table, floor.

• Press one hand onto the squeegee body by the hose connector.• Grasp the blade with your thumb and forefinger in the middle of the arch and

pull strongly until the metal band clicks open and the blade is released from the squeegee body.

• Release the metal strap and pull the blade off the squeegee body.• Clean squeegee (body, metal straps and blades) with a brush.• Mount the "rotated" or replaced blade onto the squeegee body.

Caution:Danger of injury from clamping the fingers!

• Lock the metal strap (Check position of mounting slots) into place and press the centre of it until it ”clicks” into place and presses the blade onto the squeegee body (Risk of injury).

• Turn the squeegee upside down by placing it on its suction hose connector and the bumper wheels.

• Loosen the clamping screw of the blade fastener by using an allen key (4).• Release the metal band and pull the blade off the squeegee body.• Clean squeegee (body, metal straps and blades) with a brush.• Mount the "turned" or the new blade on the nozzle body, so the creases

point outward.• Hook the metal strap into place (Check position of mounting slots) and fix it

with the screwdriver until the blade is pressed onto the squeegee body.The shape of the blades allow them to be used on all sides before needing replacement.

• Switch the machine off using the keyswitch and remove the key.

• The yellow suction filter can be easily removed (quick-fit seal).

• Clean it with water using a brush (let it dry out well).

• Brush the yellow suction filter with a soft brush or remove the fluff with a cloth.

32

Squeegee settings

If you experience an uneven suction result, the settings of the suction unit should be corrected. Proceed as follows:Before carrying out the adjustment, check that:• the blades are not damaged (replace).• the suction unit is not damaged.

Height setting (Fig. A)

• First check the distance between the floor and the running or support wheels.

The distance between running wheels number 1 and 2 and the floor must be between 1 mm and 3 mm in each case (with the blades standing vertically).The distance between support wheel number 3 and the floor must be 6 mm (with the blades standing vertically).• Switch the machine off using the keyswitch and then lower the squeegee.• To correct, loosen the hexagonal nuts number 1 and 2, and then adjust the

height by turning the Allen screw. Then firmly re-tighten the hexagonal nuts Number 1 and 2.

• Check the result while cleaning (see illustration below) and go to "Angle of Inclination" (Fig. B) if the result is unsatisfactory.

Angle of inclination(Fig. B)

• Switch the machine off.• Lower the squeegee and move the machine forward by a few centimetres

so that the blades can adopt their working position.

• To correct, loosen Allen screw number 4 and adjust the angle of inclination by turning Allen screw number 5.

Note: Carry out the correction with gradual adjustments!Firmly retighten Allen screw number 4 after the correction has been made. Then move the machine forward by a few centimetres and check the setting of the scraper edge that has been achieved. Repeat this procedure until the correct inclination is obtained.

Malfunctions

Transport• Disconnect the battery from the machine using the battery disconnection

socket.

Transport the machine in an upright position.Make sure that the machine is securely fastened within the transportation vehicle and is secured against tipping over.Refer to page 33 for the dimensions and weights.

DisposalWhen it has reached the end of its operational life, the machine and its accessories must be disposed of according to the national regulations. Your TASKI partner can support you with proper disposal upon notification.

BatteriesThe batteries must be removed from the machine before being disposed of properly.Used batteries must be disposed of in an environmentally appropriate way according to the EU guidelines 91/157/EEC

A correct angle has been achieved when the tip of the rear blade (x) is distributed over the complete width of the suction unit.

A

B

1

2

3

4x

x

5

45

Malfunction Possible causes Troubleshooting page

Machine does not run

Battery disconnection socket unplugged or keyswitch switched off

• Insert the discon-nected charger jack

• Switch the keyswitch on

28

Batteries not charged or not sufficiently charged (When swit-ching on: red battery indicator is displayed)

• Check

28

Brush does not turn

Machine has overhe-ated causing motor protection switch (trip) to cut in.

• Release the drive switch and press again 28

Foam or liquid leaking from the machine

Float malfunction

• Turn off the suction ag-gregate

• Check that the float is functioning correctly. 31

Poor vacuum performance

Floor remains wet

Soiled solution not picked up

Float closes the vacu-um air filter (overfill protection recovery tank)

• Check the recovery tank is not full 30

• Check that the float is functioning correctly. 31

The vacuum air filter is blocked

• Check whether the va-cuum air filter is clean and clean if necessary

30

Hose or nozzle blo-cked, e.g. piece of wood, residual material

• Remove the blockage

The blades do not adjust well to the floor consistancy

• Clean the squeegee

• Check that the squee-gee suspension is functioning correctly

• Squeegee adjustment 32

Worn blades • Change/turn the blades 31

Dirt sieve full (yellow)

• Remove the dirt sieve

• Knock out the coarse dirt from the sieve and rinse it under running water.

30

Insufficient out-flow of cleaning solution

Solution tank empty • Fill the solution tank 29

Solution tank filter blo-cked

• Clean solution tank fil-ter 30

Caution:This machine can only be lifted and transported with the use of aids, such as a lifting platform!

33

I25

I24

I23

I22

I21

I20

I19

I18

I17

I16

trsv

slpt

plno

nlit

frfi

esen

deda

cz

Technical data

Accessories

Dimensions of the machineAll dimensions in centimetres!

Dimensions of the battery compartmentAll dimensions in centimetres!

Machine swingo 450B

type CO450.0 CO450.X

Theoretical performance area operation width x drive speed (3) x 1000

1290 1290 m2/h

Working width 43 43 cm

Squeegee width 68 68 cm

Power cord length (internal charging unit)

- 2.5 m

Rated voltage 24V 24V DC

Rated voltage (internal battery charger)

- 230-240V AC

Frequency (internal battery charger) - 50-60 Hz

Rated power (max.) 900 900 W

Nominal power (internal battery charger)

- 195 W

Machine weight for operation 123 123 kg

Solution tank nominal 20 20 l

Recovery tank 20 20 l

Tools 1 x 43 1 x 43 cm

Brush rpm 170 170 min-1

Brush pressure 30 30 kg

Dimensions max. (L x W x H) 140x68x112 140x68x112 cm

A-weighted emission sound pressure level EN 60704-1

<70 <70 dB(A)

Vibrationtotal value of the Hand-Arm system ISO 5349

<0.5 <0.5 m /s2

Splash water protection IPX4 IPX4

Electrical protection class III II

Nr. Article CO450.0/CO450.X

7510829 Driving disc Instalok 43cm X

8504750 Scrubbing brush 43cm nylon X

8504780 Scrubbing brush abrasive 43cm X

8504800 Scrubbing brush for washed concrete 43cm X

8502830 Filling hose with universal water coupling X

Different pads(Polyester brown, blue, red, and contact pad)

X

78

48

105

140

11

2

96

64 72

68

48 46

max. 35

max.

2

0

max. 27,5