Upload
others
View
2.644
Download
0
Embed Size (px)
Citation preview
Revised 3.17.20 | Specifications subject to change without notice1 | 0 - 10V Protocol & Wiring Specifications
0 - 10V PROTOCOL
1.1 0-10V Best Wiring Practice
0 - 10V PROTOCOL
0-10V Best Wiring Practice
Any manufacturer that makes a dimmer that sinks will work with Lumenetix modules since we source the voltage.
0-10V is a topology defi ned by the International Electrotechnical Commission (IECR) 60929 Annex E standard and uses a varying DC voltage between 1 and 10V to determine the lighting level. The fi xture outputs a minimum light level below 1V w hich is defi ned as low-end . Between 1 and 10V, t h e signal corresponds to levels between the minimum and maximum output level. A signal above 10V corresponds to the maximum light level. Sometimes it is referred to as 1-10V, as that is the actual range in which the light levels will vary . Each dimmer will have their own distinct dimming profi le.
Best practice is to limit the distance run for the analog control wiring from the controller to the last driver to 300’, as a common 0-10V DC wiring type is stranded-copper twisted-pair 18AWG wiring. The wiring is stranded copper because it provides a more stable current path (as DC signals tend to be transferred by the outer edges of the conductor) while being relatively easy to work with; solid wire is usually acceptable in low-voltage systems that use
AC control power.
Whenever any part of the control circuit (the driver, dimer, or wire used) is designed for use in a Class 2 installation, it is critical that the entire control circuit be kept separate from Class 1 line voltage wiring per the requirement of National Electric Code, section 725.136. The electrical drawings must be very clear that class 1 and class 2 wiring cannot be combined. There must be separation because: a) it is possible for higher voltage wiring to induce an AC voltage in to the low voltage signal wiring; and, b) undesirable visual artifacts in the dimmed lighting can be caused when the line and low voltage wiring is run together (especially for long distances). We do not recommend installing the low voltage signal wiring in the same conduit or raceway as line voltage
wiring even when all elements of the control circuit are listed for Class 1 wiring methods.
NOTE: Lumenetix modules operate between 1-10V. All dimmers that have minimum and maximum trim pots should be set at a minimum of 1 volt and a
maximum of 10 volts, measuring the voltage at the end of the line.
0-10V Dimmers (recommended list)*Crestron
ETC
Fresco
Legrand
Leviton
Lutron
Nexlight
N-Light
Pass & Seymour
Vantage
Wattstopper
*Recommendations are subject to change. Consult your Lumenetix representative for the most updated list.
Revised 3.17.20 | Specifications subject to change without notice2 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.1a LTM2 Linear Array - 24V
0 - 10V WIRING DIAGRAMS
LTM2 Linear Array - 24V
INDEX TAB ON RED END OF CABLE CONNECTOR SHOULD LINE UP WITH INDEX SLOT ON ALM.
RIBBON CONNECTOR CABLE
TUNABLE COLOR LINEAR LED ARRAY
FIXTURE
WHITE (NEUTRAL)
BLACK (HOT)RED (+)
BLACK (Common)
LINE-IN VOLTAGE(REFER TOPOWER SUPPLY)
ALM 24V POWER CABLE (28.030.001.01)
JUNCTION BOX
araya5 LOGIC MODULE (ALM)
MAKE SURE TO ALIGNINDEX TAB TO INDEX SLOT.
CLASS-2 AC TO DC24V POWER SUPPLY(SUPPLIED BY OEM)
DIGITAL WIRES (ORANGE / WHITE WITH ORANGE STRIPE / BROWN) SHOULD REMAIN OPEN
0-10V CONTROLLER (DIM)
0-10V CONTROLLER (CCT)
VIOLET (+)
GRAY (-)
BLUE (+)
WHITE (-)
ALM 7-WIRE CONTROL CABLE (28.002.002.01)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Revised 3.17.20 | Specifications subject to change without notice3 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.1b CTM2 / DDM2 Round Array - 24V
0 - 10V WIRING DIAGRAMS
CTM2 Round Array - 24V
INDEX TAB ON RED END OF CABLE CONNECTOR SHOULD LINE UP WITH INDEX SLOT ON ALM.
MAKE SURE TO ALIGNINDEX TAB TO INDEX SLOT.RIBBON
CONNECTOR CABLE
TUNABLE COLOR ROUND LED ARRAY FIXTURE
JUNCTION BOX
WHITE (NEUTRAL)
BLACK (HOT)RED (+)
BLACK (Common)
LINE-IN VOLTAGE(REFER TOPOWER SUPPLY)
ALM 24V POWER CABLE (28.030.001.01)araya5 LOGIC MODULE (ALM)
CLASS-2 AC TO DC24V POWER SUPPLY(SUPPLIED BY OEM)
DIGITAL WIRES (ORANGE / WHITE WITH ORANGE STRIPE / BROWN) SHOULD REMAIN OPEN
0-10V CONTROLLER (DIM)
0-10V CONTROLLER (CCT)
VIOLET (+)
GRAY (-)
BLUE (+)
WHITE (-)
ALM 7-WIRE CONTROL CABLE (28.002.002.01)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
IMPORTANT: FOR THE CTM 241, THE WIRING CONNECTIONS AND THE ARAYA5 LOGIC MODULE (ALM) WILL BE MIRRORED ON TWO CONNECTOR OPENINGS (LABELED AS LEFT AND RIGHT) ON THE MODULE. THE ALM LABELED “LEFT” AT ONE END SHOULD ONLY BE ATTACHED VIA RIBBON CABLE TO THE CONNECTOR OPENING LABELED “LEFT”. THE OTHER ALM LABELED “RIGHT” AT ONE END SHOULD ONLY BE ATTACHED VIA RIBBON CABLE TO THE CONNECTOR OPENING LABELED “RIGHT”.
Revised 3.17.20 | Specifications subject to change without notice4 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.2a CTM1 24V — 0-10V Analog Control of CCT and Dimming
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
WH
ITE
(-)
BLU
E (+
)
DDIIMM CCCCTT
CLASS-224V DC POWER SUPPLY
CTM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLERS
(+)
INPUT COMMON
DIMMING
100%
1%
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Color (-)
Blue 0-10V Color (+)
Notes:1. If 0-10V control is not being used for dimming, the violet
control lead must be grounded to gray common lead.
2. CTM sources current to 0-10V control at 0.2mA nominal capacity.
3. *If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.
CTM1 24V — 0-10V Analog Control of CCT and Dimming
Revised 3.17.20 | Specifications subject to change without notice5 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.2b CTM1 12V — 0-10V Analog Control of CCT and Dimming
0 - 10V WIRING DIAGRAMS
CTM1 12V — 0-10V Analog Control of CCT and Dimming
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
WH
ITE
(-)
BLU
E (+
)
DDIIMM CCCCTT
CLASS-212V DC POWER SUPPLY
CTM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLERS
(+)
INPUT COMMON
DIMMING
100%
1%
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Lead Color and Input
Lead Color Input
Red Power 12V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Color (-)
Blue 0-10V Color (+)
Notes:1. If 0-10V control is not being used for dimming, the violet control
lead must be grounded to gray common lead.
2. CTM sources current to 0-10V control at 0.2mA nominal capacity.
3. *If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.
Revised 3.17.20 | Specifications subject to change without notice6 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.3a DDM1 24V — 0-10V Analog Control of Dimming
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
DDIIMM
CLASS-224V DC POWER SUPPLY
DDM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLER
(+)
INPUT COMMON
DIMMING
100%
1%
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
DDM1 24V — 0-10V Analog Control of Dimming0-10V Dimming Control Only. Remove power from the DDM. Connect a 0-10V control device to violet (+) and gray (-) wires. When the DDM is powered up, the 0-10V control device will adjust Dimming from 100-1%. Preset controls are not available in this confi guration.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
Notes:
1. DDM sources current to 0-10V control at 0.2mA nominal capacity.
2. Only pins 1 and 6 are used in the control cable assembly.
Revised 3.17.20 | Specifications subject to change without notice7 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.3b DDM1 12V — 0-10V Analog Control of Dimming
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
DDIIMM
CLASS-212V DC POWER SUPPLY
DDM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLER
(+)
INPUT COMMON
DIMMING
100%
1%
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
DDM1 12V — 0-10V Analog Control of Dimming0-10V Dimming Control Only. Remove power from the DDM. Connect a 0-10V control device to violet (+) and gray (-) wires. When the DDM is powered up, the 0-10V control device will adjust Dimming from 100-1%. Preset controls are not available in this confi guration.
Lead Color and Input
Lead Color Input
Red Power 12V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
Notes:
1. DDM sources current to 0-10V control at 0.2mA nominal capacity.
2. Only pins 1 and 6 are used in the control cable assembly.
Revised 3.17.20 | Specifications subject to change without notice8 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.4a CTM1 24V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
0 - 10V WIRING DIAGRAMS
CTM1 24V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Color (-)
Blue 0-10V Color (+)
Notes:1. When the lamp is connected to a 0-10V line, the default is control
of the continuous CCT range. The 0-10V line can instead be set to control scene set by sliding the Stored Scenes button to the “on” position in the araya5 Tunable Color iOS App. In this mode, the 0-10V control will toggle the light between up to 5 preset scenes. A scene is comprised of a CCT, Dim, Saturation & Hue level. Individual preset scenes can also be modifi ed and activated with the iOS app. See araya5 Tunable Color Instruction Manual for more instructions.
2. If 0-10V control is not being used for dimming, the violet control lead must be grounded to gray common lead.
3. CTM sources current to 0-10V control at 0.2mA nominal capacity.4. *If using a wall box dimmer, power only the DIM unit.
The CCT unit does not get line-in voltage.
10 V
0 VVIO
LET
(+)
GRA
Y (-)
WH
ITE
(-)
BLU
E (+
)
DDIIMM CCCCTT
CLASS-224V DC POWER SUPPLY
CTM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLERS
(+)
INPUT COMMON
DIMMING
100%
1%
Tunable Color iOS App
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Revised 3.17.20 | Specifications subject to change without notice9 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.4b DDM1 24V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
0 - 10V WIRING DIAGRAMS
DDM1 24V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
DDIIMM
CLASS-224V DC POWER SUPPLY
DDM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLERS
(+)
INPUT COMMON
DIMMING
100%
1%
Tunable Color iOS App
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
Notes:1. The 0-10V line can be set to control scene set by sliding the
Stored Scenes button to the “on” position in the araya5 Tunable Color iOS App. In this mode, the 0-10V control will toggle the light between up to 5 preset scenes. A scene is comprised of a Dim level. Individual preset scenes can also be modifi ed and activated with the iOS app. See araya5 Tunable Color Instruction Manual for more instructions.
2. DDM sources current to 0-10V control at 0.2mA nominal capacity.
3. Only pins 1 and 6 are used in the control cable assembly.
Revised 3.17.20 | Specifications subject to change without notice10 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.5a CTM1 12V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
0 - 10V WIRING DIAGRAMS
CTM1 12V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
Lead Color and Input
Lead Color Input
Red Power 12V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Presets (-)
Blue 0-10V Presets (+)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
WH
ITE
(-)
BLU
E (+
)
DDIIMM CCCCTT
CLASS-212V DC POWER SUPPLY
CTM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLERS
(+)
INPUT COMMON
DIMMING
100%
1%
Tunable Color iOS App
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Notes:1. When the lamp is connected to a 0-10V line, the default is control
of the continuous CCT range. The 0-10V line can instead be set to control scene set by sliding the Stored Scenes button to the “on” position in the araya5 Tunable Color iOS App. In this mode, the 0-10V control will toggle the light between up to 5 preset scenes. A scene is comprised of a CCT, Dim, Saturation & Hue level. Individual preset scenes can also be modifi ed and activated with the iOS app. See araya5 Tunable Color Instruction Manual for more instructions.
2. If 0-10V control is not being used for dimming, the violet control lead must be grounded to gray common lead.
3. CTM sources current to 0-10V control at 0.2mA nominal capacity.
4. *If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.
Revised 3.17.20 | Specifications subject to change without notice11 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.5b DDM1 12V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
0 - 10V WIRING DIAGRAMS
DDM1 12V (Bluetooth-integrated) — 0-10V Analog Control of Scenes / araya5 Tunable Color iOS App to Set or Amend Scenes
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
10 V
0 VVIO
LET
(+)
GRA
Y (-)
DDIIMM
CLASS-212V DC POWER SUPPLY
DDM1
NEUTRAL
HOT
WHITE
BLACKCOMMON
(+)RED
BLACK
0-10V WALLBOX CONTROLLERS
(+)
INPUT COMMON
DIMMING
100%
1%
Tunable Color iOS App
LINE IN VOLTAGE(refer to power supply)
FIXTURE
JUNCTION BOX
(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Lead Color and Input
Lead Color Input
Red Power 12V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
Notes:1. The 0-10V line can be set to control scene set by sliding the
Stored Scenes button to the “on” position in the araya5 Tunable Color iOS App. In this mode, the 0-10V control will toggle the light between up to 5 preset scenes. A scene is comprised of a Dim level. Individual preset scenes can also be modifi ed and activated with the iOS app. See araya5 Tunable Color Instruction Manual for more instructions.
2. DDM sources current to 0-10V control at 0.2mA nominal capacity.
3. Only pins 1 and 6 are used in the control cable assembly.
Revised 3.17.20 | Specifications subject to change without notice12 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.6a CTM0 24V — 0-10V Analog Control of Continuous CCT & Dimming / LCT Control of Saturation & Hue
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
COMMONINPUTINPUT
0-10V CONTROLLERS
10 V
0 VVIO
LET
GRA
Y
WH
ITE
BLU
E
Continuous CCT
COMMON
DIMMING
100%
1%
LCT
INPUT
CCT / SAT / HUE
LCT WIRELESS
DDIIMM CCCCTT
CTM0
NEUTRAL
HOT
WHITE
BLACK
RED
BLACK
CLASS-224V DC POWER SUPPLYCOMMON
(+)
FIXTURE JUNCTION BOX
LINE IN VOLTAGE(refer to power supply)
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Color (-)
Blue 0-10V Color (+)
CTM0 24V — 0-10V Analog Control of Continuous CCT & Dimming / LCT Control of Saturation & Hue
0-10V Continuous CCT Control. Remove power from the CTM. Connect a 0-10V control device to the blue (+) and white (-) wires. When the CTM is powered up, the 0-10V control will adjust the CCT over the tunable range. The Light Commissioning Tool (LCT) will control Saturation and Hue. A 0-10V control may also be added for dimming (as shown). LCT adjustments to Dimming levels are a percentage of the 0-10V Dim setting (Trim). If a 0-10V control is not used for dimming, the violet (+) and gray (-) wires must be grounded together.
Notes:1. If Scene Set is not activated using the LCT, the CTM defaults to
0-10V control of the continuous CCT range.
2. If 0-10V control is not being used for dimming, the violet control lead must be grounded to gray common lead.
3. CTM sources current to 0-10V control at 0.2mA nominal capacity.
4. If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.
Revised 3.17.20 | Specifications subject to change without notice13 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.6b CTM0 24V — 0-10V Analog Control of Dimming / LCT Control of CCT, Sat & Hue
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
INPUTINPUT 10 V
0 V VIO
LET
GRA
Y
CCT / SAT / HUE
COMMON
DIMMING
100%
1%
0-10V CONTROLLER
LCT
LCT WIRELESS
DDIIMM
NEUTRAL
HOT
WHITE
BLACK
RED
BLACK
CLASS-224V DC POWER SUPPLY
CTM0 LINE IN VOLTAGE(refer to power supply)
FIXTURE JUNCTION BOX
(+)
COMMON
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Color (-)
Blue 0-10V Color (Connect to White Common)
CTM0 24V — 0-10V Analog Control of Dimming / LCT Control of CCT, Saturation and Hue
0-10V Dimming Control Only. Remove power from the CTM. Connect a 0-10V control device to violet (+) and gray (-) wires. When the CTM is powered up, the 0-10V control device will adjust Dimming from 100-1%. Use the Light Commissioning Tool (LCT) to set CCT, Dimming, Saturation, and Hue to the desired levels and use Copy and Paste functions to match lamp settings. In this confi guration, the LCT trims the dimming level, i.e., adjustments to Dimming levels as a percentage of the 0-10V Dimming setting (Trim). Preset controls are not available in this confi guration.
Notes:1. CTM sources current to 0-10V control at 0.2mA nominal capacity.
2. Only pins 1 and 6 are used on the control cable assembly.
3. If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.
Revised 3.17.20 | Specifications subject to change without notice14 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.6c CTM0 24V — 0-10V Analog Control of Scenes / LCT to Set or Amend Scenes
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
LCT
COMMONINPUTINPUT 10 V
0 VVIO
LET
GRA
Y
WH
ITE
BLU
E
STORED SCENES
SCENE 5
SCENE 4
SCENE 3
SCENE 2
SCENE 1
COMMON
DIMMING
100%
1%
DDIIMM CCCCTT
oo
0-10V CONTROLLERS
NEUTRAL
HOT
WHITE
BLACK
RED
BLACK
CLASS-224V DC POWER SUPPLYCTM0 LINE IN VOLTAGE
(refer to power supply)
FIXTURE JUNCTION BOX
(+)
COMMON
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
CTM0 24V — 0-10V Analog Control of Scenes / LCT to Set or Amend Scenes
0-10V Preset Control. Remove power from the CTM. Connect a 0-10V control device to the blue (+) and white (common) wires. Use the Light Commissioning Tool (LCT) to set, store and enable up to fi ve preset scenes comprised of CCT, Dimming, Saturation and Hue levels. The 0-10V control will toggle between the preset scenes. A 0-10V control may also be added for dimming (as shown) and will proportionally Dim from the stored value in the preset. If a 0-10V control is not used for dimming, the violet (+) and gray (common) wires must be grounded together.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
White Signal Common for 0-10V Presets (-)
Blue 0-10V Presets (+)
Notes:1. Scene set is commissioned and activated using the LCT.
See LCT operating instructions.
2. If 0-10V control is not being used for dimming, the violet control lead must be grounded to gray common lead.
3. CTM sources current to 0-10V control at 0.2mA nominal capacity.
4. *If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.
Revised 3.17.20 | Specifications subject to change without notice15 | 0 - 10V Protocol & Wiring Specifications
0 - 10V WIRING DIAGRAMS
2.7 DDM0 24V — 0-10V Analog Control of Dimming
0 - 10V WIRING DIAGRAMS
Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)
INPUT 10 V
0 V VIO
LET
GRA
Y
COMMON
DIMMING
100%
1%
0-10 V CONTROLLER
DDIIMM
NEUTRAL
HOT
WHITE
BLACK
RED
BLACK
CLASS-224V DC POWER SUPPLYCOMMON
(+)
LINE IN VOLTAGE(refer to power supply)
FIXTURE JUNCTION BOX
THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.
DDM0 24V — 0-10V Analog Control of Dimming0-10V Dimming Control Only. Remove power from the DDM. Connect a 0-10V control device to violet (+) and gray (-) wires. When the DDM is powered up, the 0-10V control device will adjust Dimming from 100-1%. Preset controls are not available in this confi guration.
Lead Color and Input
Lead Color Input
Red Power 24V DC (+)
Black Power Common (-)
Violet 0-10V Dimming (+)
Gray Signal Common for 0-10V Dimming (-)
Notes:
1. DDM sources current to 0-10V control at 0.2mA nominal capacity.
2. Only pins 1 and 6 are used in the control cable assembly.