0 - 10V PROTOCOL...S TT V P S TT V P 4 | 0 - 10V Protocol & Wiring Specifications eise 17 Septeer 2020 | Specifications sect to cange itot notice 0 - 10V WIRING DIAGRAMS 2.2a CTM1

Revised 23 April 2021 | Specifications subject to change without notice1 | 0–10 V Protocol & Wiring Specifications

0–10 V PROTOCOL

1.1 0–10 V Best Wiring Practice

0–10 V PROTOCOL

0–10 V Best Wiring PracticeAny manufacturer that makes a dimmer that sinks will work with Lumenetix modules since we source the voltage.

0–10 V is a topology defi ned by the International Electrotechnical Commission (IECR) 60929 Annex E standard and uses a varying DC voltage between 1 and 10 V to determine the lighting level. The fi xture outputs a minimum light level below 1 V w hich is defi ned as low-end . Between 1 and 10 V, t h e signal corresponds to levels between the minimum and maximum output level. A signal above 10 V corresponds to the maximum light level. Sometimes it is referred to as 1–10 V, as that is the actual range in which the light levels will vary . Each dimmer will have their own distinct dimming profi le.

Best practice is to limit the distance run for the analog control wiring from the controller to the last driver to 300’, as a common 0–10 VDC wiring type is stranded-copper twisted-pair 18 AWG wiring. The wiring is stranded copper because it provides a more stable current path (as DC signals tend to be transferred by the outer edges of the conductor) while being relatively easy to work with; solid wire is usually acceptable in low-voltage systems that use AC control power.

Whenever any part of the control circuit (the driver, dimer, or wire used) is designed for use in a Class 2 installation, it is critical that the entire control circuit be kept separate from Class 1 line voltage wiring per the requirement of National Electric Code, section 725.136. The electrical drawings must be very clear that Class 1 and Class 2 wiring cannot be combined. There must be separation because: a) it is possible for higher voltage wiring to induce an AC voltage in to the low voltage signal wiring; and, b) undesirable visual artifacts in the dimmed lighting can be caused when the line and low voltage wiring is run together (especially for long distances). We do not recommend installing the low voltage signal wiring in the same conduit or raceway as line voltage wiring even when all elements of the control circuit are listed for Class 1 wiring methods.

NOTE: Lumenetix modules operate between 1–10 V. All dimmers that have minimum and maximum trim pots should be set at a minimum of 1 volt and a maximum of 10 volts, measuring the voltage at the end of the line.

0–10 V Dimmers (recommended list)*Crestron

ETC

Fresco

Legrand

Leviton

Lutron

Nexlight

N-Light

Pass & Seymour

VantageWattstopper

*Recommendations are subject to change. Consult your Lumenetix representative for the most updated list.


0–10 V WIRING DIAGRAMS

2.1a LTM3 Linear Array with araya Logic Module (ALM3)

0 - 10V WIRING DIAGRAMS

LTM3 Linear Array

TUNABLE COLOR LINEAR LED ARRAYFIXTURE

JUNCTION BOX

araya LOGIC MODULE (ALM3)

CABLE CAN BE CONNECTED TO EITHER OUTPUT PORT OF THE ALM3

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)

LINE-IN VOLTAGE(REFER TOPOWER SUPPLY)

ALM3 POWER CABLE (28.030.001.01)

CLASS-2 AC TO DCPOWER SUPPLY(SUPPLIED BY OEM)

0-10V CONTROLLER (DIM)

0-10V CONTROLLER (CCT)

VIOLET (+)

PINK (-)

VIOLET W/ WHITE STRIPE(+)

PINK WITH WHITE STRIPE(-)

ALM3 4-WIRE CONTROL CABLE (28.002.002.02)

THE CONSTANT HOT/LIVE MUST BE WIREDTO A SWITCHING DEVICE.



2.1b CTM3 Round Array with araya Logic Module (ALM3)

0 - 10V WIRING DIAGRAMS

CTM3 Round Array

TUNABLE COLOR ROUND LED ARRAY FIXTURE

JUNCTION BOX

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)


ALM3 POWER CABLE (28.030.001.01)araya LOGIC MODULE (ALM3)

CLASS-2 AC TO DCPOWER SUPPLY(SUPPLIED BY OEM)

0-10V CONTROLLER (DIM)

0-10V CONTROLLER (CCT)

VIOLET (+)

PINK (-)

VIOLET W/ WHITE STRIPE(+)

PINK WITH WHITE STRIPE(-)

ALM3 4-WIRE CONTROL CABLE (28.002.002.02)


CABLE CAN BE CONNECTED TO EITHER OUTPUT PORT OF THE ALM3



2.2a LTM2 Linear Array with araya Logic Module (ALM2)


LTM2 Linear Array - 24 V

INDEX TAB ON RED END OF CABLE CONNECTOR SHOULD LINE UP WITH INDEX SLOT ON ALM.

RIBBON CONNECTOR CABLE

TUNABLE COLOR LINEAR LED ARRAYFIXTURE

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)


ALM 24 V POWER CABLE (28.030.001.01)

JUNCTION BOX

araya LOGIC MODULE (ALM)

MAKE SURE TO ALIGNINDEX TAB TO INDEX SLOT.

CLASS-2 AC TO DC24 V POWER SUPPLY(SUPPLIED BY OEM)

0–10 V CONTROLLER (DIM)VIOLET (+)

GRAY (-)

BLUE (+)WHITE (-)

ALM 4-WIRE CONTROL CABLE (28.002.002.02)


0–10 V CONTROLLER (CCT)



2.2b CTM2 / DDM2 Round Array with araya Logic Module (ALM2)


CTM2 Round Array - 24 V

INDEX TAB ON RED END OF CABLE CONNECTOR SHOULD LINE UP WITH INDEX SLOT ON ALM.

MAKE SURE TO ALIGNINDEX TAB TO INDEX SLOT.RIBBON

CONNECTOR CABLE

TUNABLE COLOR ROUND LED ARRAY FIXTURE

JUNCTION BOX

WHITE (NEUTRAL)

BLACK (HOT)RED (+)

BLACK (Common)


ALM 24 V POWER CABLE (28.030.001.01)araya LOGIC MODULE (ALM)

CLASS-2 AC TO DC24 V POWER SUPPLY(SUPPLIED BY OEM)

VIOLET (+)

GRAY (-)

BLUE (+)WHITE (-)

ALM 4-WIRE CONTROL CABLE (28.002.002.02)


0–10 V CONTROLLER (DIM)

0–10 V CONTROLLER (CCT)

IMPORTANT: CTM 241 IS PROVIDED WITH TWO ALMS AND REQUIRES TWO POWER CABLE ASSEMBLIES, TWO CONTROL CABLE ASSEMBLIES, AND TWO RIBBON CABLES FOR FULL FUNCTIONALITY AND PERFORMANCE. THE WIRING CONNECTIONS AND THE ALM WILL BE MIRRORED ON TWO CONNECTOR OPENINGS (LABELED AS LEFT AND RIGHT) ON THE MODULE. THE ALM LABELED “LEFT” AT ONE END SHOULD ONLY BE ATTACHED VIA RIBBON CABLE TO THE CONNECTOR OPENING LABELED “LEFT”. THE OTHER ALM LABELED “RIGHT” AT THE OTHER END SHOULD ONLY BE ATTACHED VIA RIBBON CABLE TO THE CONNECTOR OPENING LABELED “RIGHT”.



2.3a CTM1 24 V — 0–10 V Analog Control of CCT and Dimming


CTM1 24 V — 0–10 V Analog Control of CCT and Dimming

Lumenetix part #s:28.002.001.01 (power cable assembly)28.002.002.01 (control cable assembly)

10 V

0 VVIO

LET

(+)

GRA

Y (-)

WH

ITE

(-)

BLU

E (+

)

DDIIMM CCCCTT

CLASS-224 V DCPOWER SUPPLY

CTM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK

(+)

INPUT COMMON

DIMMING

100%

1%

LINE IN VOLTAGE(refer to power supply)

FIXTURE

JUNCTION BOX


0–10 V WALLBOX CONTROLLERS

VIOLET 0–10 V

Lead Color and InputLead Color Input

Red Power 24 V DC (+)

Black Power Common (-)

Violet 0–10 V Dimming (+)

Gray Signal Common for 0–10 V Dimming (-)

White Signal Common for 0–10 V Color (-)

Blue 0-10V Color (+)

Notes:1. If 0–10 V control is not being used for dimming, the violet control

lead must be grounded to gray common lead.2. CTM sources current to 0–10 V control at 0.2mA nominal capacity. 3. *If using a wall box dimmer, power only the DIM unit. The CCT

unit does not get line-in voltage.



2.3b CTM1 12 V — 0–10 V Analog Control of CCT and Dimming


CTM1 12 V — 0–10 V Analog Control of CCT and Dimming


10 V

0 VVIO

LET

(+)

GRA

Y (-)

WH

ITE

(-)

BLU

E (+

)

DDIIMM CCCCTT


CTM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK

(+)

INPUT COMMON

DIMMING

100%

1%


FIXTURE

JUNCTION BOX



VIOLET 0–10 V







Blue 0-10V Color (+)

Notes:1. If 0–10 V control is not being used for dimming, the violet control

lead must be grounded to gray common lead.2. CTM sources current to 0–10 V control at 0.2mA nominal capacity. 3. *If using a wall box dimmer, power only the DIM unit. The CCT




2.4a DDM1 24 V — 0–10 V Analog Control of Dimming



10 V

0 VVIO

LET

(+)

GRA

Y (-)

DDIIMM

CLASS-224 V DC OWER SUPPLY

DDM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK

(+)

INPUT COMMON

DIMMING

100%

1%


FIXTURE

JUNCTION BOX


0–10 V WALLBOX CONTROLLER

VIOLET 0–10 V

DDM1 24 V — 0–10 V Analog Control of Dimming0–10 V Dimming Control Only. Remove power from the DDM. Connect a 0–10 V control device to violet (+) and gray (-) wires. When the DDM is powered up, the 0–10 V control device will adjust Dimming from 100-1%. Preset controls are not available in this confi guration.






Notes:1. DDM sources current to 0–10 V control at 0.2mA nominal

capacity.2. Only pins 1 and 6 are used in the control cable assembly.



2.4b DDM1 12 V — 0–10 V Analog Control of Dimming



10 V

0 VVIO

LET

(+)

GRA

Y (-)

DDIIMM

CLASS-212 V DC OWER SUPPLY

DDM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK

(+)

INPUT COMMON

DIMMING

100%

1%


FIXTURE

JUNCTION BOX



VIOLET 0–10 V











2.5a CTM1 24 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes


CTM1 24 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes







White Signal Common for 0–10 V Presets (-)

Blue 0–10 V Presets (+)

10 V

0 VVIO

LET

(+)

GRA

Y (-)

WH

ITE

(-)

BLU

E (+

)

DDIIMM CCCCTT


CTM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK

(+)

INPUT COMMON

DIMMING

100%

1%

Tunable Color iOS App


FIXTURE

JUNCTION BOX

(MAX. OF 8 MODULES CAN BECOMMISSIONED AT A TIME)



VIOLET 0–10 V

Notes:1. When the lamp is connected to a 0–10 V line, the default is

control of the continuous CCT range. The 0–10 V line can instead be set to control scene set by sliding the Stored Scenes button to the “on” position in the Tunable Color iOS App. In this mode, the 0–10 V control will toggle the light between up to 5 preset scenes. A scene is comprised of a CCT, Dim, Saturation & Hue level. Individual preset scenes can also be modifi ed and activated with the iOS app. See Tunable Color Instruction Manual for more instructions.

2. If 0–10 V control is not being used for dimming, the violet control lead must be grounded to gray common lead.

3. CTM sources current to 0–10 V control at 0.2mA nominal capacity.

4. *If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.



2.5b DDM1 24 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes


DDM1 24 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes


10 V

0 VVIO

LET

(+)

GRA

Y (-)

DDIIMM


DDM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK


(+)

INPUT COMMON

DIMMING

100%

1%



FIXTURE

JUNCTION BOX



VIOLET 0–10 V






Notes:1. The 0–10 V line can be set to control scene set by sliding

the Stored Scenes button to the “on” position in the Tunable Color iOS App. In this mode, the 0–10 V control will toggle the light between up to 5 preset scenes. A scene is comprised of a Dim level. Individual preset scenes can also be modifi ed and activated with the iOS app. See Tunable Color Instruction Manual for more instructions.

2. DDM sources current to 0–10 V control at 0.2mA nominal capacity.

3. Only pins 1 and 6 are used in the control cable assembly.



2.6a CTM1 12 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes


CTM1 12 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes









10 V

0 VVIO

LET

(+)

GRA

Y (-)

WH

ITE

(-)

BLU

E (+

)

DDIIMM CCCCTT


CTM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK

(+)

INPUT COMMON

DIMMING

100%

1%



FIXTURE

JUNCTION BOX




VIOLET 0–10 V

Notes:1. When the lamp is connected to a 0–10 V line, the default is

control of the continuous CCT range. The 0–10 V line can instead be set to control scene set by sliding the Stored Scenes button to the “on” position in the Tunable Color iOS App. In this mode, the 0–10 V control will toggle the light between up to 5 preset scenes. A scene is comprised of a CCT, Dim, Saturation & Hue level. Individual preset scenes can also be modifi ed and activated with the iOS app. See Tunable Color Instruction Manual for more instructions.

2. If 0–10 V control is not being used for dimming, the violet control lead must be grounded to gray common lead.

3. CTM sources current to 0–10 V control at 0.2mA nominal capacity.

4. *If using a wall box dimmer, power only the DIM unit. The CCT unit does not get line-in voltage.



2.6b DDM1 12 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes


DDM1 12 V (Bluetooth-integrated) — 0–10 V Analog Control of Scenes / Tunable Color iOS App to Set or Amend Scenes


10 V

0 VVIO

LET

(+)

GRA

Y (-)

DDIIMM


DDM1NEUTRAL

HOT

WHITE

BLACKCOMMON

(+)RED

BLACK


(+)

INPUT COMMON

DIMMING

100%

1%



FIXTURE

JUNCTION BOX



VIOLET 0–10 V






Notes:1. The 0–10 V line can be set to control scene set by sliding

the Stored Scenes button to the “on” position in the Tunable Color iOS App. In this mode, the 0–10 V control will toggle the light between up to 5 preset scenes. A scene is comprised of a Dim level. Individual preset scenes can also be modifi ed and activated with the iOS app. See Tunable Color Instruction Manual for more instructions.

2. DDM sources current to 0–10 V control at 0.2mA nominal capacity.

3. Only pins 1 and 6 are used in the control cable assembly.



2.7a CTM0 24 V — 0–10 V Analog Control of Continuous CCT & Dimming / LCT Control of Saturation & Hue



COMMONINPUTINPUT 10 V

0 VVIO

LET

GRA

Y

WH

ITE

BLU

E

Continuous CCT

COMMON

DIMMING

100%

1%

LCT

INPUT

CCT / SAT / HUE

LCT WIRELESS

DDIIMM CCCCTT

CTM0 NEUTRAL

HOT

WHITE

BLACK

RED

BLACK

CLASS-224 V DCPOWER SUPPLYCOMMON

(+)

FIXTURE JUNCTION BOX




VIOLET 0–10 V BLUE 0–10 V







Blue 0–10 V Color (+)

CTM0 24 V — 0–10 V Analog Control of Continuous CCT & Dimming / LCT Control of Saturation & Hue

0–10 V Continuous CCT Control. Remove power from the CTM. Connect a 0–10 V control device to the blue (+) and white (-) wires. When the CTM is powered up, the 0-10V control will adjust the CCT over the tunable range. The Light Commissioning Tool (LCT) will control Saturation and Hue. A 0–10 V control may also be added for dimming (as shown). LCT adjustments to Dimming levels are a percentage of the 0–10 V Dim setting (Trim). If a 0–10 V control is not used for dimming, the violet (+) and gray (-) wires must be grounded together.

Notes:1. If Scene Set is not activated using the LCT, the CTM defaults

to 0–10 V control of the continuous CCT range.2. If 0–10 V control is not being used for dimming, the violet

control lead must be grounded to gray common lead.3. CTM sources current to 0–10 V control at 0.2mA nominal

capacity. 4. If using a wall box dimmer, power only the DIM unit. The CCT




2.7b CTM0 24 V — 0–10 V Analog Control of Dimming / LCT Control of CCT, Sat & Hue



INPUTINPUT 10 V

0 V VIO

LET

GRA

Y

CCT / SAT / HUE

COMMON

DIMMING

100%

1%

LCT

LCT WIRELESS

DDIIMM

NEUTRAL

HOT

WHITE

BLACK

RED

BLACK


CTM0 LINE IN VOLTAGE(refer to power supply)


(+)

COMMON



VIOLET 0–10 V







Blue 0–10 V Color (Connect to White Common)

CTM0 24 V — 0–10 V Analog Control of Dimming / LCT Control of CCT, Saturation and Hue

0–10 V Dimming Control Only. Remove power from the CTM. Connect a 0–10 V control device to violet (+) and gray (-) wires. When the CTM is powered up, the 0-10V control device will adjust Dimming from 100-1%. Use the Light Commissioning Tool (LCT) to set CCT, Dimming, Saturation, and Hue to the desired levels and use Copy and Paste functions to match lamp settings. In this confi guration, the LCT trims the dimming level, i.e., adjustments to Dimming levels as a percentage of the 0–10 V Dimming setting (Trim). Preset controls are not available in this confi guration.

Notes:1. CTM sources current to 0–10 V control at 0.2mA nominal

capacity. 2. Only pins 1 and 6 are used on the control cable assembly.3. If using a wall box dimmer, power only the DIM unit. The CCT




2.7c CTM0 24 V — 0–10 V Analog Control of Scenes / LCT to Set or Amend Scenes



LCT

COMMONINPUTINPUT 10 V

0 VVIO

LET

GRA

Y

WH

ITE

BLU

E

STORED SCENES

SCENE 5

SCENE 4

SCENE 3

SCENE 2

SCENE 1

COMMON

DIMMING

100%

1%

DDIIMM CCCCTT

ooNEUTRAL

HOT

WHITE

BLACK

RED

BLACK


CTM0 LINE IN VOLTAGE(refer to power supply)


(+)

COMMON



VIOLET 0–10 V BLUE 0–10 V

CTM0 24 V — 0–10 V Analog Control of Scenes / LCT to Set or Amend Scenes0–10 V Preset Control. Remove power from the CTM. Connect a 0–10 V control device to the blue (+) and white (common) wires. Use the Light Commissioning Tool (LCT) to set, store and enable up to fi ve preset scenes comprised of CCT, Dimming, Saturation and Hue levels. The 0–10 V control will toggle between the preset scenes. A 0–10 V control may also be added for dimming (as shown) and will proportionally Dim from the stored value in the preset. If a 0–10 V control is not used for dimming, the violet (+) and gray (common) wires must be grounded together.








Notes:1. Scene set is commissioned and activated using the LCT.

See LCT operating instructions.2. If 0–10 V control is not being used for dimming, the violet

control lead must be grounded to gray common lead.3. CTM sources current to 0–10 V control at 0.2mA nominal

capacity.4. *If using a wall box dimmer, power only the DIM unit. The CCT




2.8 DDM0 24 V — 0–10 V Analog Control of Dimming



INPUT 10 V

0 V VIO

LET

GRA

Y

COMMON

DIMMING

100%

1%

0–10 V CONTROLLER

DDIIMM

NEUTRAL

HOT

WHITE

BLACK

RED

BLACK


COMMON

(+)




VIOLET 0–10 V









0 - 10V protocol1.1 0-10V Best Wiring Practice

0–10 V WIRING DIAGRAMS2.1a LTM3 Linear Array with ALM32.1b CTM3 Round Array with ALM32.2a LTM2 Linear Array with ALM22.2b CTM2 / DDM2 Round Array with ALM22.3a CTM1 24V - 0-10V Analog Control of CCT and Dimming2.3b CTM1 12V - 0-10V Analog Control of CCT and Dimming2.4a DDM1 24V - 0-10V Analog Control of Dimming2.4b DDM1 12V - 0-10V Analog Control of Dimming2.5a CTM1 24V (Bluetooth-integrated) - 0-10V Analog Control of Scenes2.5b DDM1 24V (Bluetooth-integrated) - 0-10V Analog Control of Scenes2.6a CTM1 12V (Bluetooth-integrated) - 0-10V Analog Control of Scenes2.6b DDM1 12V (Bluetooth-integrated) - 0-10V Analog Control of Scenes2.7a CTM0 24V - 0-10V Analog Control of Continuous CCT & Dimming / LCT Control of Saturation & Hu2.7b CTM0 24V - 0-10V Analog Control of Dimming / LCT Control of CCT, Sat & Hue2.7c CTM0 24V - 0-10V Analog Control of Scenes / LCT to Set or Amend Scenes2.8 DDM0 24V - 0-10V Analog Control of Dimming

Documents

0 - 10V PROTOCOL...S TT V P S TT V P 4 | 0 - 10V Protocol & Wiring Specifications eise 17 Septeer 2020 | Specifications sect to cange itot notice 0 - 10V WIRING DIAGRAMS 2.2a CTM1