View
3
Download
0
Category
Preview:
Citation preview
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2014 American Honda Motor Co., Inc. – All Rights Re
VERSION 2
ROOF RACK RAILSP/N 08L02-T0A-110Aserved. AII 00475 (1411
2015 CR-V
) 0
Issue Date
NOV 2014
PARTS LIST
Left roof rack rail cover
Right roof rack rail cover
Left roof rack rail base
Right roof rack rail base
12 Torx nuts
2 Self-tapping screws
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriver
T-15 and T-30 Torx bits
Eye protection (face shield, safety goggles, etc.)
File
Felt-tip pen
Blanket
Approx. 120 mm height empty cardboard box
Torque wrench
Ruler
Tape
The following tools are available through the Honda Tooland Equipment Program. On the iN, click on: Service >Service Bay > Tool and Equipment Program, then enterthe number under “Search”. Or, call 888-424-6857.
• Plastic Trim Tool (T/N SILTRIMTL10)
• Air Saw (T/N AT192A)
Illustration of the Roof Rack Rails Installed on theVehicle
QD31801AA
RIGHT ROOFRACK RAIL
LEFT ROOFRACK RAIL
1 of 68L02-T0A-110A
INSTALLATION
Customer Information: The information in thisinstallation instruction is intended for use only by skilledtechnicians who have the proper tools, equipment, andtraining to correctly and safely add equipment to yourvehicle. These procedures should not be attempted by“do-it-yourselfers.”
NOTE:
• Be extremely careful not to damage the roof and otherfinished surfaces of the body when installing the roofrack rails.
• The weight of the cargo must not exceed the maximumweight capacity of 75 kg (165 lbs).
Installing the Roof Rack Rails
1. Measure rearward from the windshield molding, andmark the left roof molding at the measurementshown.
QA11301AD
LEFT ROOFMOLDING
FRONT
17 mm(0.7 in.)
MARKLEFT ROOFMOLDING
WINDSHIELDMOLDING
FELT-TIPPEN
2 of 6 AII 00475
2. Using a plastic trim tool, pry up on the left roofmolding cover to release one retaining tab and oneclip.
QA22108AD
FRONT
LEFT ROOFMOLDING COVER
CLIP
RETAIN-ING TAB
PLASTICTRIMTOOL
TAILGATE
3. Pull the left roof molding toward the outside ofvehicle to release the locking tab, and then press thelocking tab toward the inside of vehicle, and releasethe left roof molding from the vehicle. Whenremoving the left roof molding, start from the rear ofvehicle and work towards the front.
Q0D0801BD
FRONT
LEFT ROOFMOLDING
CROSSSECTION
CLIP LOCKING TAB
LEFT ROOFMOLDING(Press towardinside of vehicle.)
LOCKING TAB(Pull towardoutside of vehicle.)
LEFT ROOFMOLDING
(1411) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
4. While pulling up the left roof molding, remove the twoclips. Insert the plastic trim tool alternately to eachslots in the clip, and release the locking tabs in theorder shown. When removing the left roof molding,start from the rear of vehicle and work towards thefront. Be careful not to deform the roof molding.
QA60801AG
FRONT
CLIP LOCKINGTAB
LEFT ROOFMOLDING
1 2 4 635
Approx.7 mm(0.3 in.)width.
PLASTICTRIM TOOL
PLASTICTRIMTOOL
Approx.1 mm(0.04 in.)thickness.
PLASTICTRIM TOOL
CLIP
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 00475
5. Place a blanket over the roof of vehicle under the leftroof molding. Be careful not to deform the roofmolding when measuring and cutting.
Q0D0802CD
LEFT ROOFMOLDING
FRONT
BLANKET
6. Place an empty cardboard box (approx. 120 mm tall)under the left roof molding near the mark.
Q0D0803BD
LEFT ROOFMOLDING
MARK
EMPTYCARDBOARDBOX
Approx.120 mm(4.7 in.)
FRONT
(1411) 3 of 6
7. While wearing an eye protection, use an air saw tocut the left roof molding at the mark. Do not use acutting wheel or shears to cut the left roof molding, itwill damage the left roof molding. Have an assistanthold the rear edge while cutting.
Q0D0804BD
LEFT ROOFMOLDING
MARKAIR SAW
FRONT
8. Remove the cardboard box and blanket.
9. Secure the two clips removed in step 4.
QA60802AG
LEFT ROOFMOLDING
2 CLIPS
FRONT
4 of 6 AII 00475
10. Insert flat-tip screwdrivers alternately between thegreen clip and the stud bolt as shown. While pullingon the green clip, release the locking tab on thegreen clip from the groove on the stud bolt notch bynotch, and remove the green clip. Repeat the sameprocedure to remove the two purple clips.
Q0D0805BD
FRONT
FLAT-TIPSCREWDRIVERS(Alternately insert torelease the locking tab.)
GREENCLIP
CLIP
STUDBOLT
CROSSSECTION
FLAT-TIPSCREWDRIVERS
LOCKINGTAB
STUDBOLT
CLIP
2 PURPLECLIPS
(1411) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
11. Remove the red clip and the three yellow clips.
Q0D0806BD
REDCLIP
FRONT
3 YELLOWCLIPS
12. Using a flat-tip screwdriver wrapped with tape,remove the left roof molding cover from the left roofmolding (one retaining tab). Discard the left roofmolding.
QA22109BD
LEFT ROOFMOLDING COVER
RETAIN-ING TAB
LEFT ROOFMOLDING(Discard.)
TAPE
FLAT-TIPSCREWDRIVER
© 2014 American Honda Motor Co., Inc. – All Rights Reserved. AII 00475
13. Reinstall the left roof molding cover in its originalposition on the roof.
QA22110AD
FRONT
LEFT ROOFMOLDING COVER
CLIP
RETAIN-ING TAB
TAILGATE
14. Install the left roof rack rail base to the vehicle usingsix Torx nuts. Torque the Torx nuts to 10-15 N·m (1.0-1.5 kgf·m, 8-11 lbf·ft).
QD31802AA
6 STUDBOLTS
6 TORX NUTS10-15 N·m(1.0-1.5 kgf·m,8-11 lbf·ft)
FRONT
LEFT ROOF RACKRAIL BASE
(1411) 5 of 6
15. Hook the front of the left roof rack rail cover to the leftroof rack base.
QD31803AA
LEFT ROOFRACK RAILCOVER
LEFT ROOFRACK RAILBASE
HOOK
LEFT ROOF RACKRAIL BASE
LEFT ROOFRACK RAILCOVER
16. Secure the left roof rack rail cover to the left roof rackbase with eight clips.
QD31804AA
8 CLIPS
LEFT ROOFRACK RAILCOVER
6 of 6 AII 00475
17. Secure the left roof rack rail cover to the left roof rackbase with one self-tapping screw.
QD31805AA
LEFT ROOFRACK RAILCOVER
SELF-TAPPINGSCREW
18. Repeat steps 1 through 17 to install the right roofrack rail.
USE AND CARE
Check the roof rack rail mounting bolts frequently, andre-tighten if necessary.
(1411) © 2014 American Honda Motor Co., Inc. – All Rights Reserved.
Recommended