Upload
niroj-bhujel
View
82
Download
5
Tags:
Embed Size (px)
Citation preview
Avlite Systems
Solar Airfield Light
Global reputation for unsurpassed reliability…
TECHNOLOGYSolar lighting systems
LED as light source
Solar LED lighting best value of money at 1/3 of
the cost of mains power lighting installation
Suitable as an emergency back-up system
installed alongside traditional mains-powered
lighting
OPERATING PRINCIPLE
Solar module converts sunlight to a electrical current used
to charge the battery at day
The battery provides power to operate at night
Microprocessor drives an array of LED through DC/DC
converter
Over charging protection
If the light has auto control then, On darkness, the
microprocessor initiate a program check and after
approximately 1 min. the light turn on.
PRODUCTS
OF
AVLITE
AV-70 MODEL
Used in such as runways, taxiways and helipads
Operating reliably in low sunlight conditions
Incorporate dual high performance solar modules
FEATURESIntegrated solar /battery system
Fast and easy to deploy –no
programming
IP68 rating
User-replaceable battery
Ultra- high intensity LEDs
AV-70
AVLITE AV-70-G-SWA)LIGHT CHARACTERISTICS
Light Source: 12 ultra-high intensity LEDS
Peak Intensity (cd): Steady on( Blue -2.8 Red -6.8,
Green-9 white7 Yellow-6.5)
Flashing(Blue -5.5 Red -18.2 Green-21.9 white-
19.1 Yellow-15.1)
Horizontal Output (degree): 360
Reflector type: Omni directional 360 degree LED
reflector
ELECTRICAL CHARACTERISTICS
Operating voltage(V): 3.6
Temperature Range: -40 to 80⁰C
Solar Characteristics
Solar Module type: Multicrystalline
Output Power: 2.5 (2X1.25) watt
Solar Module Efficiency(%): 14
Charging Regulation: Microprocessor control
Power supply
Battery type: High grade NIMH
Battery Capacity: 8 Ahr
Nominal voltage: 3.6 V
Light Operation
Light is activated by ON/OFF Switch
Intensity and flash settings need to be set prior to
installation
i)Remove the marked flash adjustment bung from the
base of the light and set internal toggle switch to ‘ON’
ii)Using DIP switches, Intensity setting of the lights are
adjusted
iii)Set rotary switches to the required flash code
iv)Replace flash adjustment bung
INSTALLING THE LIGHT ASSEMBLY: MOUNTING
OPTIONS Rubber tile
Rubber Tile Installation
Frangible Concrete Mount
Fig: Frangible Concrete Mount Installation
Frangible Stake Mount
Frangible Stake Mount Installation
AV-70-RF MODEL
INTRODUCTION
Radio controlled version of AV70
Allows pilot safely navigate runways and
apron areas
Used in conjunction with Pilot Activated
Lighting Control(PALC) or simple hand held
controller
Fig: PALC Fig: Handheld controller
AV-ALS-RC-2.4-AVMESH
Radio Controlled Front
View
Radio Controlled Side
View
AV-ALS-RC-2.4-AVMESH
A model of Handheld controller
Features
Range: Up to 1.4 KM
Temperature: -40 to 80⁰C
Frequency: 2.4GHz
Nominal Voltage: 7.2 V
Battery Capacity: 4 Ah
AVLITE:AV-70-B-RF
Works by using a hand held radio
controller and setup entire airfield,
airport or air base.
Each light also has an operational
range of 1.4 Km
MODES OF OPERATION
Always ON operational Mode
STANDBY operational mode
Dusk till Dawn Operational mode
Light Group
Light is selected through rotary switch
Controller can select any one of the 10 individual light
groups or all (By default 0)
Timeout Duration
Visible only when timeout model is enabled
Time before the LED intensity reverts back to its LOW intensity state or standby
Duration can set from 1 to 60 minutes
LED Bank Setup
Allow a runway to change from visible to IR
Battery Diagnostic
Used to check the battery voltage in every light
If the battery voltage is within operational range the light will turn off for 1 sec, flash once for 1 sec and again turn off for 1 sec.
Otherwise, the light will turn off for 1 sec, flash twice then turn off for 1 sec
Graph for Diagnostic Test
Sending Command
Every time command is set by pressing SEND
button
Better to have diagnostic test once per day
Red Status LED Determine the fault
Present in radio controlled model
Situated near the Flash Code Switches
Runway B Only is to be High Intensity, with a Timeout of
8 minutes and Runway A will be low Intensity
Flash Codes All AV-70-RF lights are programmed to be steady on
Alternatively, they are able to be programmed to flash in
any of the 250 different flash codes i.e 00 to FF
Charging the radio controller
Unscrew the protective cap from the charging port
Insert the charging terminal into the Radio controller
Plug the charger into a wall socket and turn the charger
on
The charger has a LED to indicate the charge
sequences
i) green: Unit is fully charged
ii) orange: Unit is charging
iii) Red: A fault is occuring
PROGRAMMING THE RADIO CONTROL SYSTEM
Turn on radio controller
Press and hold the menu button for 3 sec
Menu contains following submenu
a. Screen back light
b. Connection method
i) Radio control
ii) Direct connection
c. Flash code selection- Enable or disable
d. Sync. Menu selection- Enable or disable
e. Advanced operation- Enable or disable
f. Diagnostic- Enable or disable
g. Radio information
i. Radio encryption key
If you change the radio encryption key then, the light
encryption key by which that remote control should
also changes
j. Press ‘send’ to save the Radio Control System
AV-425-RF-Model
FEATURES
Peak intensity(cd): Steady on (Red 25, Green
37, white 27.5, yellow 92.5)
Operating voltage: 12 V
Solar module type: Multi crystalline
Output: 18 watt
Battery: Sealed Lead Acid
Battery Capacity: 24 Ah
PROGRAMMING THE LIGHT USING CABLE
INTERFACE AND HAND HELD CONTROLLERNOTE: PRESS ‘SEND’ AFTER EACH SELECTION
Remove the light head to access the programming port
Connect the programming cable between light and radio
controller
Turn on the radio controlled
Turn on light at the red master switch
Press and hold the menu for 3 sec
Using menu key scroll down submenu to connection
method and select direct connection
Advanced operation mode
Light group: 0 to 10 or all
Intensity: Low, Medium or High
Flash code : From 000 to 1FF
Sync. Offset: (If sync is enabled during radio control
system programming)
Radio encryption key
Now, put the radio controller to the radio connection mode
AVLITE OBSTRUCTION LIGHT
AV-OL-ILAB-12-R
Universal DC Low intensity
obstruction light
Operating range: 12 to 48
VDC
Alarm relay for internal
diagnostic checking
( supply voltage too low, LED
failure etc)
Adjustable intensity setting
i) Type A: 10 cd
ii) Type B: 32 cd
Battery: 26 Ah
Current draw (mA) @12 V
Type A @ 10 cd steady on Imax=65
Type B @ 32 cd steady on Imax = 120
Power (W)
Type A @ 10 cd steady on Pmax=0.9
Type B @ 32 cd steady on Pmax = 1.5
OPERATION
Turn ON <=100 lux
Turn OFF>=150 lux
Intensity setting Open the light head
Change the intensity DIP switch
AV-OL-ILAB-UM-R Universal AC Low
intensity Obstruction
Light
Operating Range 110 to
240 V AC
Power
Type A @ 10 cd steady
on Pmax=2 W
Type B @ 32 cd steady
on Pmax = 3W
Others all the
properties and
operational principle
similar to AV-OL-ILAB-
12-R
Any
queries
END
AND
THANK YOU
EVERY ONE FOR
LISTENING