7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 1/12
**PRINT THIS PAGE FIRST** to check
that the printed scale is correct. The
black line below should be five inches
long. If it measures to 5 inches then
print the rest of the pages.
*You will need to trim any side of a page
that has the red guide lines. These lines
should match up exactly and will be 3
inches long.
PDF NOTES and TIPS
5 inches
Print scale
Set aileron deflection to 3/8 of a
Set aileron deflection to 7/8 of a
*** Make sure “Page Scaling” is turned OFF ***
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 2/12
inch up and down for TRAINER flying. inch up and down for SPORT flying.
Center of gravity must be between these two lines. COG is between
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 3/12
www.Mik eysRC.
5/8 and 2 inches back from wing leading edge
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 4/12
om
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 5/12
MAX elevator deflection 3/8 inch up and down.
t t o
a d d
o n e
.
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 6/12
Aielron servo straps
3 motor mount pieces.
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 7/12
Plane Requirements*11.1V 1200 -1500mAh 15-20C Li-po.
*1000 - 1400(for faster flying) kv brushless motor with flat mount.
*25 - 30 amp speed control.
*10 X 6 prop.
*3, 9 gram servos.. Add another servo if you want a rudder.
Build Materials*1/4 inch Foam core for the fuselage, wings and tail. You can
use 6 mm Depron also but you will have to add extra support
to it to make it more ridgid.
*About 8 popsicle sticks.
*1/16 Drill Rod (from a hardware store) or RC pushrods,
about 20 inches are needed. OR ypu can use RC pushrods if youhave them.
*Hot glue or 5 min epoxy.
*Thick packing tape for control surface hinges.
* 8, 12 inch wooden BBQ skewers.
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 8/12
BBQ Skewers glued on the
fuselage with hot glue or epoxy.
Their location is approximate but
needed to stiffen up the fuselage.
Battery Tray. Use the piece cutout to make the battery area.
Turn it on it’s side and glue it back in the hole and support it with
angled popsicle stick pieces.
3 Motor Mount Pieces. Make sure the front
piece is glued first to the front of the fuselage.
It must follow the angle of the nose to give the
motor the propper down angle. Then glue either
a small piece if thin plywood or several pieces of popscile sticks to the front motor mount to give
the motor screws something to screw into.
3D view of Sport Trainer
This BBQ skewer is glued on TOP of the wing.
Also put a piece of 1.5 - 2 inch wide packingtape running the length over the top of it.
This makes it more aerodynaic and adds lift.
Glue popsicle sticks
here for skids.
Glue popsicle stick on topof the nose for added
stiffness.
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 9/12
R u
d d e r
i f y o u
w a
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 10/12
w w w .Mik ey sRC .com
COPYRIGH T 2009 MikeysRCDo NOT redistribute
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 11/12
Cut THIS piece out and use it as the battery
tray if you are a more advanced pilot and
want LESS stability but better barrel rolls.
Cut THIS piece out and use it as the battery
tray if you are a beginner pilot and
want MORE stability for training flying.
7/28/2019 MRC Sport Trainer
http://slidepdf.com/reader/full/mrc-sport-trainer 12/12
Want a little aviation humor?
Visit www.airtoons.comfor some funny variations on the
typical informative.....yet boring
airline saftey cards.
Servos
Aileron servo straps
Battery tray
Top front view of plane
3 motor mount
pieces.