Instruction ManualBedienungsanleitungManuel d’utilisationManuale di Istruzioni
®
450 X
2EN
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to
operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
Additional Safety Precautions and WarningsAge Recommendation: Not for children under 14 years. This is not a toy. • Alwayskeepasafedistanceinalldirectionsaroundyourmodeltoavoidcollisionsorinjury.Thismodeliscontrolledbyaradiosignalsubjecttointerference
from many sources outside your control. Interference can cause momentary loss of control.• Alwaysoperateyourmodelinopenspacesawayfromfull-sizevehicles,trafficandpeople.• Alwayscarefullyfollowthedirectionsandwarningsforthisandanyoptionalsupportequipment(chargers,rechargeablebatterypacks,etc.).• Alwayskeepallchemicals,smallpartsandanythingelectricaloutofthereachofchildren.• Alwaysavoidwaterexposuretoallequipmentnotspecificallydesignedandprotectedforthispurpose.Moisturecausesdamagetoelectronics.• Neverplaceanyportionofthemodelinyourmouthasitcouldcauseseriousinjuryorevendeath.• Neveroperateyourmodelwithlowtransmitterbatteries.
NOTICEAllinstructions,warrantiesandothercollateraldocumentsaresubjecttochangeatthesolediscretionofHorizonHobby,Inc.Forup-to-dateproductliterature,visithorizonhobby.comandclickonthesupporttabforthisproduct.
The Battery Charger included with your aircraft is designed to safely charge theLi-Pobattery.
CAUTION:Allinstructionsandwarningsmustbefollowedexactly.MishandlingofLi-Pobatteriescanresultinafire,personalinjury,and/or property damage.
• Byhandling,chargingorusingtheincludedLi-Pobatteryyouassumeallrisksassociatedwithlithiumbatteries.
• Ifatanytimethebatterybeginstoballoonorswell,discontinueuseim-mediately. If charging or discharging, discontinue and disconnect. Continuing to use, charge or discharge a battery that is ballooning or swelling can result in fire.
• Alwaysstorethebatteryatroomtemperatureinadryareaforbestresults.• Alwaystransportortemporarilystorethebatteryinatemperaturerangeof
40–120º F. Do not store battery or model in a car or direct sunlight. If stored in a hot car, the battery can be damaged or even catch fire.
• NEVERUSEANNi-CdORNi-MHCHARGER.Failuretochargethebatterywithacompatiblechargermaycausefireresultinginpersonalinjuryand/orproperty damage.
• NeverdischargeLi-Pocellstobelow3Vunderload.• Nevercoverwarninglabelswithhookandloopstrips.• Neverleavechargingbatteriesunattended.• Alwayschargebatteriesawayfromflammablematerials.• Neverchargebatteriesoutsidesafetermperaturerange.• Neverchargebatteriesoutsiderecommendedlevels.• Neverchargedamagedbatteries.• Storebatteriessafely.
Battery Warnings
Meaning of Special Language
3 EN
Table of Contents
Introduction
Length 25.8 in (655mm)
Height 8.8 in (225mm)
Main Rotor Diameter 28.4 in (721mm)
Tail Rotor Diameter 6.1 in (155mm)
Flying Weight 25.3 oz (717 g)
Motor 440H Brushless outrunner, 4200Kv (installed)
ESC 35-amp brushless (installed)
Battery 3S 11.1V 2200mAh 30C Li-Po (included)
Charger DC Li-Po Balancing Charger (included)
Flybarless Unit
Spektrum AR7200BX with BeastX technology (installed)
Swash Servos DS76 (installed)
Tail Servo DS76T (installed)
Blade 450 X Specifications
Components
To register your product online, visit www.bladehelis.com
Charging the Flight Battery ...........................................................................6Battery Charging Codes ................................................................................6LowVoltageCutoff(LVC) ...............................................................................6TransmitterSetup .........................................................................................7Transmitter and Receiver Binding ................................................................10Throttle Hold ...............................................................................................10Installing the Flight Battery .........................................................................10Control Tests ...............................................................................................11Flying the Blade 450 X ................................................................................12AR7200BXParameterMenuTips ................................................................13Post-FlightInspectionsandMaintenance ....................................................13AR7200BXDefaultBlade450XSetup .........................................................14Blade Helicopter Belt Tension .....................................................................15TroubleshootingGuide ................................................................................15Limited Warranty ........................................................................................16WarrantyandServiceContactInformation ..................................................17CustomerServiceInformation .....................................................................17ComplianceInformationfortheEuropeanUnion ..........................................17Parts List ....................................................................................................58Optional Parts .............................................................................................60
TheBlade®450XfeaturestheSpektrum™AR7200BX7-channelreceiverwithintegratedBeastX™flybarlesstechnology.TheSpektrumAR7200BXprovidesmax-imumprecision,stability,andcontrolforadvanced3Dmaneuvers.Anewflybarlessrotorheaddesign,combinedwiththeSpektrumAR7200BX,resultsinsimplifiedsetup,easiermaintenanceandalighterhelicopter.TheBlade450Xalsoincludesahigh-performance440Hbrushlessmotor,digitalservosandcarbonfibermainbladesdesignedtohandletherigorsof3Dflybarlessflight.
Readthismanualthoroughlybeforeyourfirstflight.Thismanualcontainsimportantpre-flightinformationtohelpensureyourfirstflightisagreatone.
4EN
Charging the Flight Battery
The Battery Charging Process1. Chargeonlybatteriesthatarecooltothetouchandarenotdamaged.Lookatthebatterytomakesureitisnotdamagede.g.,swollen,bent,brokenor
punctured.
2. Connectthechargertoa12Vpowersource,notingproperpolarity.
3. TheCHARGESTATUSLEDglowssolidred.
4. Connectthebatterybalanceleadtothecharger.Thebalanceconnectoriskeyedtopreventreversepolarity.
5. TheCELLSTATUSLEDsglowsolidgreenoryellowandtheCHARGESTATUSLEDglowssolidredwhenthebatteryischarging.
6. Charging is complete when all LEDs glow solid red.
7. Always unplug the battery from the charger immediately upon completion of charging.
CAUTION: Overcharging a battery can cause a fire.
TheBlade450XcomeswithaDCbalancingchargerand3SLi-Pobattery.UseonlyHorizonHobbyapprovedbatterypacksandchargerscompatiblewiththisproduct. Never leave the battery and charger unattended during the charge process. Failure to follow the instructions properly could result in a fire. When charging,makecertainthebatteryisonaheat-resistantsurface.Chargetheflightbatterybeforebindingtheaircraftorperformingcontroltests.
DC Li-Po Balancing Charger Features•Charges3-celllithiumpolymerbatterypacks•1.8Achargerate•LEDchargestatusindicator•LEDcellbalanceindicator•12Valligatorclipinputcord
Specifications•Inputpower:minimum3Aat11.5–15VDC•Charges3-cellLi-Popackswithminimumcapacityof1800mAh
3S 11.1V 2200mAh 30C Li-Po Battery Pack (E-flite EFLB22003S30)TheBlade450X3SLi-Pobatterypackfeaturesabalancingleadthatallowsyoutosafelychargeyourbatterypackwhenusedwiththeincluded Blade450XLi-Pobalancingcharger.Theincludedflightbatteryissafetochargeupto3C.
CAUTION: The balance connector must be inserted into the correct port of your charger prior to charging.
CAUTION: OnlyuseachargerspecificallydesignedtochargeaLi-Pobattery.Failuretodosocouldresultinfirecausinginjuryorpropertydamage.
CAUTION: Neverexceedtherecommendedchargerate.
Low Voltage Cutoff (LVC)
Battery Charging Codes
TheESCwillcontinuouslylowerpowertothemotoruntilcompleteshutdownwhenthebatteryreaches9Vunderload.Thishelpspreventover-dischargeoftheLi-Pobattery.LandimmediatelywhentheESCactivatesLVC.ContinuingtoflyafterLVCcandamagethebattery,causeacrashorboth.Crashdamageandbatteriesdamagedduetoover-dischargearenotcoveredunderwarranty.
RepeatedlyflyingthehelicopteruntilLVCactivateswilldamagethehelicopterbattery.
DisconnectandremovetheLi-Pobatteryfromtheaircraftafterusetopreventtrickledischarge.Duringstorage,makesurebatterychargedoesnotfallbelow3Vpercell.
Cell Status LEDs Charge Status LED InstructionOff RedSolid Battery charger is powered. LiPo battery is not connected.
Yellow RedSolid LiPobatteryisconnected.Chargerisbalancingthebatterypackcells
Green RedSolid LiPo battery is connected and charging
Red RedSolid LiPo battery is connected and charging is complete
Off BlinkingRedNoLiPobatteryconnected:Voltageisoutsidetheinputvoltagerange LiPobatteryconnected:Atleastonebatterycellvoltageisbelow2.6V
5 EN
Transmitter Setup
Spektrum DX6i
SETUP LIST
SYSTEM LIST
ADJUST LIST
ADJUST LIST
POS-0POS-0 POS-1
Spektrum DX7/DX7se
Model Type Reverse Swash Type Timer
HELI THRO—N 1Servo90Degree Type—Down
AILE—N Time—4:00
ELEV—N Switch—Trainer
RUDD—R
GYRO—N
PITC—R
Model Type Swash Type Input Select
HELI 1ServoNorm AUX2 GEAR INH GYRO
D/R Expo
AILE 0 100% INH
ELEV0 100% INH
RUDD0 100% INH
AILE 1 85% INH
ELEV1 85% INH
RUDD1 85% INH
AUTO D/R EXP
NORM INH
ST-1 INH
ST-2 INH
HOLD INH
AILE ELEV RUDD
EXP LIN EXP LIN EXP LIN
D/R100% D/R100% D/R100%
AILE ELEV RUDD
EXP LIN EXP LIN EXP LIN
D/R85% D/R85% D/R85%
TRAVEL ADJUST
THRO 100%
AILE 100%
ELEV 100%
RUDD 100%
GYRO 100%
PITC 100%
TRAVEL ADJUST
THRO AILE
H 100% L 100%
L 100% R 100%
ELEV RUDD
D 100% L 100%
U100% R 100%
GEAR PIT
+ 100% H 100%
-100% L 100%
AUX2
+ 100%
-100%
SUB-TRIM*
THRO 0
AILE 0*
ELEV 0*
RUDD 0*
GYRO 0
PITC 0
SUB-TRIM*
THRO 0
AILE 0*
ELEV 0*
RUDD 0*
GEAR 0
PITC 0
AUX2 0
GYRO
Rate SW-F.Mode
0 77.0% NORM 0
1 77.0% STUNT 0
GYRO SENS
AUTO F.MODE
RATE NORM 0
0 77.0% STNT 0
1 77.0% HOLD 0
THRO HOLD
HOLDPOS 0.0%
SW RUDDD/R
TIMER
DOWN-T 4:00
SWASH MIX
INH
REVERSING SW
THRO AILE ELEV RUDD GEAR PIT AUX2
N N N R N N N
THRO CUR
L 2 3 4 H
NORM 0% 30% 60% 60% 60%
STUNT 100% 100% 100% 100% 100%
HOLD 10% 10% 10% 10% 10%
THRO CURVE
L 1 2 3 H
NORM 0% 30% 60% 60% 60%
ST-1 100% 100% 100% 100% 100%
ST-2 100% 100% 100% 100% 100%
PITC CUR
L 2 3 4 H
NORM 30% 40% 50% 75% 100%
STUNT 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100%
PITCH CURVE
L 1 2 3 H
NORM 30% 40% 50% 75% 100%
ST-1 0% 25% 50% 75% 100%
ST-2 0% 25% 50% 75% 100%
HOLD 0% 25% 50% 75% 100%
SWASH MIX
INHIBIT
Program your transmitter before attempting to bind or fly the helicopter. TransmitterprogrammingvaluesareshownbelowfortheSpektrumDX6i,DX7/DX7se,DX7sandDX8.TheSpektrummodelfilesforAirWare™transmittersarealsoavailablefordownloadonlineintheSpektrumCommunity.
NOTICE:WhenusingaFutabatransmitterwithaSpektrumDSMmodule,youmustreversethethrottlechannel.
*Neverusesub-trimsortrimsonAILE,ELEVorRUDDchannelswiththeAR7200BX.
*Neverusesub-trimsortrimsonAILE,ELEVorRUDDchannelswiththeAR7200BX.
6EN
SYSTEM LIST
FUNCTION LIST
Spektrum DX7s
SERVO SETUP
TRAVEL SUB TRIM* REVERSE
THROTTLE 100 100 THROTTLE 0 THROTTLE N
AILERON 100 100 AILERON 0* AILERON N
ELEVATOR 100 100 ELEVATOR 0* ELEVATOR N
RUDDER 100 100 RUDDER 0* RUDDER R
GYRO 100 100 GYRO 0 GYRO N
PITCH 100 100 PITCH 0 PITCH N
AUX2 100 100 AUX2 0 AUX2 N
D/R AND EXPO
POS D/R D/R EXPO SW
AILERON 0 100 100 0 AILED/R
AILERON 1 85 85 0 AILED/R
ELEVATOR 0 100 100 0 ELEVD/R
ELEVATOR 1 85 85 0 ELEVD/R
RUDDER 0 100 100 0 RUDDD/R
RUDDER 1 85 85 0 RUDDD/R
GYRO
SW FMode
CH Gear
NORMAL/POS0 54
STUNT1/POS1 54
HOLD 54
TIMER
MODE Countdown
TIME 4:00Tone/Vibe
START Throttle Out
POS 10
THROTTLE CURVE
LOW 25% 50% 75% HIGH EXPO
N 0 30 60 60 60 INH
1 100 100 100 100 100 INH
H 0 0 0 0 0 INH
TAIL CURVE
LOW 25% 50% 75% HIGH EXPO
N 0 0 0 0 0 INH
1 0 0 0 0 0 INH
H 0 0 0 0 0 INH
PITCH CURVE
LOW 25% 50% 75% HIGH EXPO
N 30 40 50 75 100 INH
1 0 25 50 75 100 INH
H 0 25 50 75 100 INH
Model Type Swash Type Switch Select F Mode Setup Warnings Frame Rate
Helicopter 1ServoNormalAllSwitchesINH
FlightMode—FMode
Throttle —Over 10 11ms
Hold — Hold Stunt1—Active DSMX
Hold—Active
Alarm—Tone/Vibe
THROTTLE CUT
INHIBIT
GOVERNOR
SW-INHIBIT
Transmitter Setup
*Neverusesub-trimsortrimsonAILE,ELEVorRUDDchannelswiththeAR7200BX.
7 EN
SYSTEM LIST
FUNCTION LIST
Spektrum DX8
SERVO SETUP
TRAVEL SUB TRIM* REVERSE SPEED
THROTTLE 100 100 THROTTLE 0 THROTTLE N THROTTLE NORM
AILERON 100 100 AILERON 0* AILERON N AILERON NORM
ELEVATOR 100 100 ELEVATOR 0* ELEVATOR N ELEVATOR NORM
RUDDER 100 100 RUDDER 0* RUDDER R RUDDER NORM
GYRO 100 100 GYRO 0 GYRO N GYRO NORM
PITCH 100 100 PITCH 0 PITCH N PITCH NORM
AUX2 100 100 AUX2 0 AUX2 N AUX2 NORM
AUX3 100 100 AUX3 0 AUX3 N AUX3 NORM
D/R AND EXPO
POS D/R D/R EXPO SW
AILERON 0 100 100 0 AILED/R
AILERON 1,2 85 85 0 AILED/R
ELEVATOR 0 100 100 0 ELEVD/R
ELEVATOR 1,2 85 85 0 ELEVD/R
RUDDER 0 100 100 0 RUDDD/R
RUDDER 1,2 85 85 0 RUDDD/R
GYRO
SW FMode
CH Gear
NORMAL/POS0 54
STUNT1/POS1 54
STUNT2/POS2 54
HOLD 54
TIMER
MODE Countdown
TIME 4:00Tone/Vibe
START Throttle Out
POS 25
THROTTLE CURVE
LOW 25% 50% 75% HIGH EXPO
N 0 30 60 60 60 INH
1 100 100 100 100 100 INH
2 100 100 100 100 100 INH
H 0 0 0 0 0 INH
TAIL CURVE
LOW 25% 50% 75% HIGH EXPO
N 0 0 0 0 0 INH
1 0 0 0 0 0 INH
2 0 0 0 0 0 INH
H 0 0 0 0 0 INH
PITCH CURVE
LOW 25% 50% 75% HIGH EXPO
N 30 40 50 75 100 INH
1 0 25 50 75 100 INH
2 0 25 50 75 100 INH
H 0 25 50 75 100 INH
Model Type Swash Type Switch Select F Mode Setup Trim Step Warnings Frame Rate
Helicopter 1ServoNormal AllSwitchesINH FlightMode—FMode THR 5 Throttle —Over 10 11ms
Hold — Hold AIL** 0 Stunt1—Act DSMX
ELE** 0 Stunt2—Act
RUD**0 Hold—Act
RTRIM0 Alarm—Tone/Vibe
LTRIM0
TYPE Common
THROTTLE CUT
INHIBIT
SWASHPLATE
INHIBIT
GOVERNOR
INHIBIT
Transmitter Setup
**Changing trim step to zero disables the trim for that channel.
*Neverusesub-trimsortrimsonAILE,ELEVorRUDDchannelswiththeAR7200BX.
8EN
Installing the Flight Battery
CAUTION: AlwaysdisconnecttheLi-Pobatteryfromtheaircraftreceiverwhennotflyingtoavoidover-dischargingthebattery.Batteriesdischargedtoavoltage lower than the lowest approved voltage may become damaged, resulting in loss of performance and potential fire when batteries are charged.
WARNING: YoumustmovethethrottletotheLOW/OFFpositionduringbinding.Failuretodosomaycausetherotorbladestospinandthe helicopter to lift during the AR7200BX initialization, which could result in damage to property and injury.
1. Lower the throttle.2. Power on the transmitter.3.Centerthethrottletrim.4.ToallowtheESCtoarmandtokeeprotorsfrominitiatingatstartup,turn
onthrottleholdandnormalflightmodebeforeconnectingtheflightbattery. Please refer to your transmitter manual for more information on programmingthrottleholdandnormalflightmode.
5.Attachhookmaterialtothehelicopterframeandloopmaterialtothebattery.
6.Installtheflightbatteryonthehelicopterframe.Securetheflightbatterywithahookandloopstrap.ConnectthebatterycabletotheESC.
CAUTION:AlwayskeepthepowerleadpositionedAWAYfromtheeleva-tor servo. Failure to do so could cause the lead to get caught, resulting in a crash causing property damage and injury.CAUTION: Makesuretheflightbatterydoesnotcomeincontactwiththemotor.Failuretodosowillcausethemotor,ESCandbatterytooverheat, resulting in a crash causing property damage and injury.
7. Do not move the helicopter until the AR7200BX initializes. The swashplate will move up and down, indicating that the unit is ready. The AR7200BX willalsoemitasolidBLUEStatusLEDwhenitisready
8.Thehelicoptermotorwillemit2tones,incdicatingtheESCisarmed.
Binding Procedure
1. ProgramyourtransmitterusingtheTransmitterSetupfoundinthismanual.
2. InsertthebindplugintheBND/DATportonthereceiver.
3. ConnecttheflightbatterytotheESC.TheHmenuLEDshouldbeflashing,indicatingtheAR7200BXisinbindmode.
4. Movethethrottlesticktothedesiredfailsafeposition(lowthrottlepositioninnormalmode).
5. FollowtheproceduresofyourspecifictransmittertoenterBindMode.Thesystemwillconnectwithinafewseconds.Onceconnected,theHLEDwillturn off and the AR7200BX will start the initialization process.
6. Whentheinitializationprocessiscomplete,menuLEDHwillturnOFFandtheStatusLEDlightwillcomeONsolidBLUE.
7. DisconnecttheflightbatteryandremovethebindplugfromtheAR7200BX.Storethebindpluginaconvenientplace.
NOTICE: Removethebindplugtopreventthesystemfromenteringbindmodethenexttimethepoweristurnedon.If you encounter problems, obey binding instructions and refer to transmitter troubleshooting guide for other instructions. If needed, contact the appropriate HorizonProductSupportoffice.ForalistofcompatibleDSM®transmitters,pleasevisitwww.bindnfly.com.
BindingistheprocessofprogrammingthereceivertorecognizetheGUID(GloballyUniqueIdentifier)codeofasinglespecifictransmitter.Youneedto‘bind’yourchosenSpektrum™DSM2™/DSMX®technologyequippedaircrafttransmittertothereceiverforproperoperation.
Transmitter and Receiver Binding
Throttle Hold
Throttle hold only turns off the motor on an electric helicopter. You maintain pitch and direction control.
The blades will spin if throttle hold is OFF. For safety, turn throttle hold ON any timeyouneedtotouchthehelicopterorcheckthedirectioncontrols.
Throttle hold is also used to turn off the motor if the helicopter is out of control, in danger of crashing, or both.
Please refer to your transmitter manual for more information on programming throttle hold.
9 EN
Rudder 1. Power on the transmitter.2. Turn TH HOLD ON and put transmitter in normal mode. 3. ConnectthehelicopterbatterytotheESC NOTICE:DonotallowthehelicoptertomoveuntiltheStatusLEDissolid
blue and all menu LEDs are OFF. The gyro will not operate correctly if the helicoptermovesbeforetheStatusLEDissolidblue.
4. Movetheruddersticktotheright.Thetailrotorbladesmoveasshown.Ifthey do not move as shown, reverse the rudder channel in the transmitter (refertoyourtransmittermanualforinstructions).
5. Releasetheruddercontrol.Manuallyturn the helicopter nose to the left. The tail rotor blades automatically move as shown. If they do not move as shown, refer to the AR7200BX manual for information on reversing thetailsensordirection(SetupmenupointF).
CyclicWhenusingaflybarlessrotorhead,youarecontrollingrotationalrateswhile the AR7200BX controls the servos. You are not directly controlling the servos with the transmitter.
It is normal for the swashplate to slowly move back to its original position after a stick input and for the servos to not move at the same speed as your control sticks.
1.Tiltthehelicopterforward.Theswashplateshouldtiltbackward.2.Tiltthehelicopterbackward.Theswashplateshouldtiltforward.3.Rollthehelicopterleft.Theswashplateshouldrollright.4. Roll the helicopter right. The swashplate should roll left.5. If the swashplate does not move in the correct direction, you will need to
reverse the cyclic sensor direction. Refer to the AR7200BX manual for moreinformation(SetupmenupointM).
Control Tests
MODE 2 MODE 1
Cyclic and Collective Control TestTurn on Throttle Hold when doing the control tests
Rudder and Cyclic Gyro Test
Elevator
ail ail
ail
Side View
ail
Side View
Aileron
ail ail
ailail
Rear ViewRear View
ail
ail
Collective Pitch
ail
ail
Rear ViewRear View
CAUTION:YoumustcompletetheRudderandCyclictestspriortoflight.Failuretocompletethetestsensuringthesensordirectionsarenotreversedcancause the helicopter to crash, resulting in property damage and injury.
10EN
Motor Control TestPlacethehelicopteroutdoorsonaclean,flatandlevelsurface(concreteorasphalt)freeofobstructions.Alwaysstayclearofmovingrotorblades.1Themotorbeepstwicewhenthehelicopter’sESCarmsproperly.Before
you continue, confirm that TH HOLD is ON. WARNING: The motor will spin when throttle is increased while TH HOLD is OFF.
2.Checktheswashplatedirectionstoensuretheyaremovinginthecorrectdirection. Please refer to the diagrams above for reference.
WARNING: Stayatleast30feet(10meters)awayfromthehelicopterwhenthemotorisrunning.Donotattempttoflythehelicopteratthistime.
3. Ensurethethrottleisloweredcompletely.Confirmthetransmitterisstillsettonormalflightmode.Turnthrottleholdoffatthistime.Slowlyincrease the throttle until the blades begin to spin. The main blades spin clockwisewhenviewingthehelicopterfromthetop.Thetailrotorbladesspincounterclockwisewhenviewingthehelicopterfromtheright-handside.
NOTICE:Ifthemainrotorbladesarespinningcounterclockwise,makesureyouare in normal mode and reduce the throttle to low immediately. Turn TH HOLD ON. Disconnect the battery from the helicopter and reverse any two motor wire connectionstotheESCandrepeatthemotorcontroltest.
Consult local laws and ordinances before choosing a location to fly your aircraft.
Selectalarge,openareaawayfrompeopleandobjects.Yourfirstflightsshouldbeoutdoorsinlow-windconditions.Alwaysstayatleast30feet (10meters)awayfromthehelicopterwhenitisflying.
TheBlade450Xisnotintendedtobeflownindoorswhereitmightbe possibletoflyaBladeSRorBladeCX2.Experiencedpilotsmayfinditpossibletoflythehelicopterinalargegymnasium.
CAUTION: TheBlade450Xisintendedforpilotswithexperienceflyingaerobatic, collective pitch helicopters. The Blade 450 X is more respon-sivethanotherBladehelicopters,suchastheBladeSR.Ifyouarenotanexperienced3Dorcollectivepitchhelicopterpilot,donotattempttoflythis product.
TakeoffDeliberatelyincreasethrottleandestablishahoveratleast24”(0.6meter)high, outside of ground effect.
CAUTION: Do not give any aileron, elevator or rudder commands before takeofforthehelicoptermaycrashduringtakeoff.
FlyingThe helicopter lifts off the ground when the rotor head reaches a suitable speed.Establishalow-levelhovertoverifyproperoperationofyourhelicopter.Youmustnotsetanytrim;theflybarlessdesignoftheBlade450Xrenderstrimunnecessary.Settingtrimorsub-trimcancauseanunwanteddriftorrota-tion of the helicopter.
FirstflightsshouldbeperformedinnormalmodeandlowcyclicandrudderdualratesuntilyouarefamiliarwiththeflyingmanneroftheBlade450X.Discovertheratesthatfityourflyingstyle.
CAUTION:Alwaysflythehelicopterwithyourbacktothesunandthewindtopreventlossofflightcontrol.
LandingEstablish a low level hover. Deliberately lower the throttle until the helicopter lands. Do not give any aileron, elevator or rudder commands when the helicop-ter is landing.
When the helicopter is in stunt mode:
-Therotorheadspeedisconstant. -Themainrotorwillincreasenegativepitchasthethrottle/collectivestickismovedfromthemiddlestickpositiontothelowstickposition.Negativepitchallowsthehelicoptertoflyupsidedownandperformaerobatics.
Change between stunt and idle up modes in a hover with the throttle near the hoveringstickposition.
The helicopter may go up or down when you change between modes due to the difference in the throttle and pitch curves.
WARNING: Do not use wooden main blades with the Blade 450 X or injuryand/orpropertydamagecouldoccur.Only use Blade 450 X ap-proved carbon fiber main blades.
If the cyclic control is too slow or too fast, adjust the transmitter dual rates, expoorthrottlecurvetofityourliking.
Flying the Blade 450 X• Alwayskeepaircraftinsightandundercontrol.• Alwaysturnonthrottleholdatlossofcontrolorrotorstrike.•Always use fullly charged batteries• Alwayskeeptransmitterpoweredonwhileaircraftispowered.•Always remove batteries before disassembly• Alwayskeepmovingpartsclean.• Alwayskeeppartsdry.
•Always let parts cool after use before touching.•Always remove batteries after use.• Alwayskeeppeopleandpetsatleast30feetawaywhentheflightbattery
is connected.•Never operate aircraft with damaged wiring•Never touch moving parts
❏ Checkallscrewsandensurethattheyaretight ❏ Checkbelttensionandensurethatitisnottootightortooloose ❏ Checkmainandtailbladestoensuretheyarenotdamaged ❏ Checkalllinksandmakesuretheymovefreelybutdonotpopoffeasily ❏ Checkthatflightbatteryandtransmitterbatteryarefullycharged ❏ Checkallwirestoensurethattheyarenotcut,pinched,orchaffedand
are properly secured ❏ Checkallwireconnections
❏ Checkgearsandmakesurenoteetharemissing ❏ Do a complete control test ❏ Checkthatservosarefunctioningproperly ❏ Checktomakesureflightbatteryisproperlysecured ❏ ChecktomakesureAR7200BXisproperlysecured
Blade 450 X Pre-Flight Checklist
11 EN
Gyro Gain Adjustment
•Ifthetailwagsoroscillates,lowerthegainonthegyro.
On your transmitter’s gyro menu, decrease the gyro gain values a small amount at a time until the helicopter is stable within a particular flight mode
•Ifthetailisdriftingwhilehovering,increasethegainonthegyro.
On your transmitter, increase the gyro gain values a small amount at a time until the tail starts to wag/oscillate. Afterwards, reduce the gain until the tail stops wagging/oscillating within a particular flight mode.
Post-Flight Inspections and Maintenance
Ball Links Makesuretheplasticballlinkholdsthecontrolball,butisnottight(binding)ontheball.Whenalinkistoolooseontheball,itcanseparatefromtheballduringflightandcauseacrash.Replacewornballlinksbeforetheyfail.
Cleaning Makesurethebatteryisnotconnectedbeforecleaning.Removedustanddebriswithasoftbrushoradrylintfreecloth.
Bearings Replacebearingswhentheybecomenotchy(stickyinplaceswhenturning)ordraggy.
Wiring Makesurewiringdoesnotblockmovingparts.Replacedamagedwiringandlooseconnectors.
Fasteners Makesuretherearenoloosescrews,otherfastenersorconnectors.Donotovertightenmetalscrewsinplasticparts.Tightenscrewsopartsarematedtogether,thenturnscrewonly1/8thofaturnmore.
Rotors Makesurethereisnodamagetorotorbladesandotherpartswhichmoveathighspeed.Damagetothesepartsincludescracks,burrs,chipsorscratches.Replacedamagedpartsbeforeflying.
Gyro MakesuretheAR7200BXissecurelyattachedtotheframe.Replacethedouble-sidedtapewhennecessary.ThehelicopterwillcrashiftheAR7200BXseparates from the helicopter frame.
Blade Helicopter Belt Tension
Belt tension that is too tight results in loss of power and causes the belt to wearmorequickly.Tensionthatistooloosecancausebeltdamageandlossoftailrotorcontrolinflight.
To check for proper belt tension:1. Viewthetailrotordrivebeltthroughtheopeningatthebackofthemain
frame.2. Useahexwrenchorstandardscrewdrivertocompressthebeltthroughthe
opening.3. Applylightpressureonthebelt,compressingthebelttowardtheleftside
of the tail boom.4. The belt tension is correct if the compressed side of the belt reaches ap-
proximatelyhalfwaytotheoppositesideofthebelt.a. If the compressed side of the belt reaches farther than halfway to
the other side of the belt, the tension is too loose.b. If the compressed side of the belt does not reach halfway to the
other side of the belt, the tension is too tight.
To adjust belt tension:1. Loosen the two horizontal stabilizer screws.2. Loosenthefourscrewsatthebackofthemainframe.3. Slidetheboomforwardorafttoadjustthebelttension.4. When the belt tension is properly adjusted, tighten the four screws at the
backoftheframe.5. Tighten the horizontal stabilizer screws.
12EN
AR7200BX Default Blade 450 X Setup
*The AR7200BX included with your Blade 450 X helicopter is pre-programmed with these default settings. If you perform a factory reset on the included AR7200BX will default back to these default Blade 450 X helicopter settings.
ToperformaBlade450XAR7200BXfactoryreset,enteranySetupmenuandpressthesetupbuttonfor10seconds.Afterperformingthefactoryreset,youwillneedtore-centertheswashplateservosbyusingsetupmenuG.
If you update the firmware on the AR7200BX to non-Blade 450 X firmware: All Blade 450 X helicopter default settings will be deleted. You will need to complete the entire AR7200BX setup process before flying the helicopter again. Please refer to the Spektrum AR7200BX instruction manual included with your helicopter for more information.
Status-LED: OFF Purple Red Flashing Red SolidBlue Flashing Blue Solid
A Mounting orientation upright (vertical)flat(horizontal)*
B Swashplateservo-frequency User defined50 Hz 65 Hz 120 Hz 165 Hz 200 Hz*
CTailservo- center position pulse length
User defined
960 μs 760 μs 1520 μs*
D Tailservo- frequency User defined50 Hz 165 Hz 270* Hz 333Hz 560 Hz
E Tailservo- rotor endpoints Tailstick-movetorightendpointandwait/leftendpointandwait
F Tail-sensor direction normal* reversed
G Swashplate- servo centering Reference positionELE center pos.
AIL center pos.
PIT center pos.
H Swashplate- mixer User defined mechanical 90° 120°* 140° 140°(1=1)
I Swashplate- servo directions nor|rev|rev nor|nor|rev* nor|rev|nor nor|nor|nor
JSwashplate- cyclic pitch geometry
Aileronstick–adjust6°cyclicpitchontherollaxis(bladesalignedwithfuselage)
K Collective pitch range Collectivestickonmaxandminpositionandusetailsticktoadjustdesiredpitch. Stocksettingsprovide+/-12degreesofcollectivepitch.
L Swashplate- cyclic limit Moveaileron,elevatorandpitchsticks–adjustmaxlimitswithtailstick
M Swashplate- sensor directions rev | rev rev | nor nor | rev nor | nor*
N Pirouette optimization direction normal reversed*
Status-LED: OFF Purple Red Flashing Red Solid
Blue Flashing Blue Solid
A Swashplate- cyclic center adjustment
Aileronandelevatorstick–resetwithtailstick
B Control behavior User defined
normal sport pro extreme transmitter*
C Swashplate- pitching up behavior User defined
very low low medium* high very high
D Tail-HeadingLock gain User defined
very low low medium* high very high
E Stick deadband User defined
1 2* 3 4 5
F Tail-torque precompensation IX) User defined
off* low-nor high-nor low-rev high-rev
G Cyclic response User defined
normal slightly increased*
increased high very high
H Pitch boost User defined
off* low medium high very high
PARAMETER MENU Menu LED is flashing quickly
SETUP MENU Menu LED solid
Firmwareversion4503.0.0
13 EN
AR7200BX Fine-tuning and Adjustment
Blade 450 X Troubleshooting Guide
Problem Possible Cause Solution
Helicopter will not bind to the trans-mitter(duringbinding)
Lowflightbatteryortransmitterbatteryvoltage Fullychargeorreplacetheflightbatteryand/ortransmitterbatteries
AR7200BX is not in bind mode MakesurethebindplugisconnectedtotheAR7200BXBND/DATport
Transmitter is not in bind mode Refer to your transmitter's instruction manual for binding instructions
Transmitter too close to the helicopter during binding pro-cess
Poweroffthetransmitter.Movethetransmittertoalargerdistancefromthehelicopter.Disconnectandreconnecttheflightbatterytothehelicopterandfollow binding instructions.
Helicopterwillnotlinktothetrans-mitter(afterbinding)
Helicopter is bound to a different model memory (ModelMatchradiosonly)
Disconnecttheflightbattery.Selectthecorrectmodelmemoryonthetrans-mitter.Reconnecttheflightbattery
Flightbattery/Transmitterbatterychargeistoolow Replace or recharge batteries
AR7200BX will not initialize The helicopter was moved during initialization Lay the helicopter on its side during initialization if windy
The transmitter is powered off Power on the transmitter
Controls are not centered Centerelevator,aileronandruddercontrols.Makesurethethrottleisatidle
Helicopter will not respond to the throttle but responds to other controls
Throttlenotatidleand/orthrottletrimistoohigh Lowerthethrottlestickandlowerthethrottletrim
The transmitter is not in normal mode or throttle hold is on Makesurethetransmitterisinnormalmodeandthrottleholdisoff
ThemotorisnotconnectedtotheESCorthemotorwiresare damaged ConnectthemotorwirestotheESCandcheckmotorwiresfordamage
Flight battery charge is too low Replaceorrechargeflightbattery
Throttle channel is reversed Reverse the throttle channel on the transmitter
Helicopterpowerislacking
Flight battery has low voltage Fullychargetheflightbattery
Flight battery is old or damaged Replacetheflightbattery
Flight battery cells are unbalanced Fullychargetheflightbattery,allowingthechargertimetobalancethecells
ExcessivecurrentisbeingdrawnthroughtheBEC Checkallservosandthehelicoptermotorfordamage
Tail drive belt tension is not correct. See"CheckingTailDriveBeltTension"inthismanual
Helicopter will not lift off
Mainrotorheadisnotspinninginthecorrectdirection Makesurethemainrotorheadisspinningclockwise.Refertothemotorcontrol test
Transmitter settings are not correct Checkthrottleandpitchcurvesettingsandpitchcontroldirection
Flight battery has low voltage Fullychargetheflightbattery
Mainrotorbladesareinstalledbackwards Installthemainrotorbladeswiththethickersideastheleadingedge
AR7200BX Parameter Menu Tips
RefertotheSpektrumAR7200BXmanualtofinetunetheBlade450XtoyourflyingandcontrolstyleviatheAR7200BXparametermenu.
Ifyouwouldliketochangethecontrolbehavioroftheflybarlesssystemtoapre-definedbehaviorintheAR7200BX,adjustparameterB(defaultbehavioristransmitter).
IfyouwouldliketohavethecyclicbehaviortofeelmorelinearORmorelikeaflybarredhelicopter,increasethecyclicresponsebyadjustingparameterG(defaultis‘slightlyincreased’).
RefertotheSpektrumAR7200BXmanualforspecificdetailsoneach parameter.
Observed Behavior Suggested Adjustment
Cyclic response is too slow or too fastAdjustendpointstofityourflyingstyle.Refertoyourtransmitterinstructionmanualformore information
AdjustthecontrolbehaviorparameterintheAR7200BXtofityourflyingstyle.
Control inputs feel delayed Increase Dial 2 on the AR7200BX
The helicopter seems to overshoot control input and then return Decrease Dial 2 on the AR7200BX
The helicopter tail stops too abruptly DecreaseDial3ontheAR7200BX
The helicopter tail does not stop precisely
IncreaseDial3ontheAR7200BX
Increase the rudder gain in your transmitter
AdjusttherudderheadinglockgainparameterintheAR7200BX
Makesurethetaildrivebelttensionisadjustedcorrectly
14EN
What this Warranty CoversHorizonHobby, Inc. (“Horizon”)warrantstotheoriginalpurchaserthat theproductpur-chased(the“Product”)willbefreefromdefectsinmaterialsandworkmanshipatthedateof purchase. What is Not CoveredThiswarrantyisnottransferableanddoesnotcover(i)cosmeticdamage,(ii)damageduetoactsofGod,accident,misuse,abuse,negligence,commercialuse,orduetoimproperuse,installation,operationormaintenance,(iii)modificationofortoanypartoftheProd-uct,(iv)attemptedservicebyanyoneotherthanaHorizonHobbyauthorizedservicecenter,or(v)ProductsnotpurchasedfromanauthorizedHorizondealer.OTHERTHANTHEEXPRESSWARRANTYABOVE,HORIZONMAKESNOOTHERWARRANTYOR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIEDWARRANTIES,INCLUDING,WITHOUT LIMITATION,THE IMPLIEDWARRANTIES OF NON-INFRINGEMENT,MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE. THE PURCHASERAC-KNOWLEDGESTHATTHEYALONEHAVEDETERMINEDTHATTHEPRODUCTWILLSUITABLYMEETTHEREQUIREMENTSOFTHEPURCHASER’SINTENDEDUSE.Purchaser’s RemedyHorizon’ssoleobligationandpurchaser’ssoleandexclusiveremedyshallbethatHorizonwill,atitsoption,either(i)service,or(ii)replace,anyProductdeterminedbyHorizontobedefective.HorizonreservestherighttoinspectanyandallProduct(s)involvedinawar-rantyclaim.ServiceorreplacementdecisionsareatthesolediscretionofHorizon.Proofofpurchaseisrequiredforallwarrantyclaims.SERVICEORREPLACEMENTASPROVIDEDUNDERTHISWARRANTYISTHEPURCHASER’SSOLEANDEXCLUSIVEREMEDY.Limitation of LiabilityHORIZONSHALLNOTBELIABLEFORSPECIAL,INDIRECT,INCIDENTALORCONSEQUEN-TIALDAMAGES,LOSSOFPROFITSORPRODUCTIONORCOMMERCIALLOSSINANYWAY,REGARDLESSOFWHETHERSUCHCLAIMISBASEDINCONTRACT,WARRANTY,TORT,NEG-LIGENCE,STRICTLIABILITYORANYOTHERTHEORYOFLIABILITY,EVENIFHORIZONHASBEENADVISEDOFTHEPOSSIBILITYOFSUCHDAMAGES.Further,innoeventshalltheli-abilityofHorizonexceedtheindividualpriceoftheProductonwhichliabilityisasserted.AsHorizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.LawThesetermsaregovernedbyIllinoislaw(withoutregardtoconflictoflawprincipals).Thiswarranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICESQuestions, Assistance, and ServicesYourlocalhobbystoreand/orplaceofpurchasecannotprovidewarrantysupportorser-vice. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to [email protected], or call 877.504.0233toll freetospeaktoaProductSupportrepresentative.Youmayalsofindinformation on our website at www.horizonhobby.com.Inspection or ServicesIfthisProductneedstobeinspectedorserviced,pleaseusetheHorizonOnlineServiceRequestsubmissionprocessfoundonourwebsiteorcallHorizontoobtainaReturnMer-chandiseAuthorization(RMA)number.PacktheProductsecurelyusingashippingcarton.Pleasenotethatoriginalboxesmaybe included,butarenotdesignedtowithstandtherigorsofshippingwithoutadditionalprotection.Shipviaacarrierthatprovidestrackingand insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until itarrivesand isacceptedatour facility.AnOnlineServiceRequest isavailableathttp://www.horizonhobby.comundertheSupporttab.Ifyoudonothaveinternetaccess,pleasecontactHorizonProductSupporttoobtainaRMAnumberalongwithinstructionsforsubmittingyourproductforservice.WhencallingHorizon,youwillbeaskedtoprovideyour complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMAnumber,alistoftheincludeditems,andabriefsummaryoftheproblem.Acopyof your original sales receipt must be included for warranty consideration. Be sure your name,address,andRMAnumberareclearlywrittenontheoutsideoftheshippingcarton.NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo bat-tery, please contact the appropriate Horizon Product Support office.Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product willbeservicedorreplacedfreeofcharge.Serviceorreplacementdecisionsareatthesole discretion of Horizon.Non-Warranty ServiceShould your service not be covered by warranty service will be completed and pay-ment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the servicewithout notification. Service estimates areavailable upon request. You must include this request with your item submitted for service. Non-warrantyserviceestimateswillbebilledaminimumof½houroflabor.Inadditionyouwillbebilledforreturnfreight.Horizonacceptsmoneyordersandcashierschecks,aswellasVisa,MasterCard,AmericanExpress,andDiscovercards.BysubmittinganyitemtoHorizonforservice,youareagreeingtoHorizon’sTermsandConditionsfoundonourwebsitehttp://www.horizonhobby.com/Service/Request/.
Limited Warranty
Problem Possible Cause Solution
Flight battery will not charge
Input voltage to the charger is too low Inputvoltagemustbebetween11.5–15VDCwithaminimum3Acurrent
The battery balance tab is damaged Makesurethebalancetabwiresarefullyseatedinthebalanceplug
Theflightbatteryisoverdischarged Ifanycellvoltagedropsbelow3V,thebatteryisdamagedandmustbere-placed.
The helicopter tail spins out of control
Ruddercontroland/orsensordirectionreversed Makesuretheruddercontrolandtheruddersensorareoperatinginthecor-rect direction
Tail servo is damaged Checktherudderservofordamageandreplaceifnecessary
Inadequate control arm throw Checktheruddercontrolarmforadequatetravelandadjustifnecessary
Tail belt is too loose Makesurethetaildrivebelttensionisadjustedcorrectly
Thehelicopterwobblesinflight
Cyclic gain is too high Decrease Dial 1 on the AR7200BX
Headspeed is too low Increasethehelicopter'sheadspeedviayourtransmittersettingsand/orusingafreshlychargedflightpack
Dampers are worn Replace the main rotor head dampers
Blade 450 X Troubleshooting Guide, continued
15 EN
Warranty and Service Contact Information
Country of Purchase Horizon Hobby Address PhoneNumber/EmailAddress
UnitedStatesofAmerica
HorizonServiceCenter(Electronicsandengines)
4105 Fieldstone RdChampaign,Illinois,61822USA
877-504-0233OnlineRepairRequestvisit:www.horizonhobby.com/service
HorizonProductSupport (Allotherproducts)
4105 Fieldstone RdChampaign,Illinois,61822USA
UnitedKingdom Horizon Hobby LimitedUnits1-4PloytersRdStapleTyeHarlow,Essex,CM187NS,UnitedKingdom
+44(0)[email protected]
Germany HorizonTechnischerService Christian-Junge-Straße1 25337Elmshorn,Germany+49(0)[email protected]
France HorizonHobbySAS14RueGustaveEiffelZoned’ActivitéduRéveilMatin91230Montgeron
+33(0)[email protected]
China Horizon Hobby – ChinaRoom 506, No. 97 Changshou Rd. Shanghai,China200060
+86(021)51809868 [email protected]
Customer Service Information
Country of Purchase Horizon Hobby Address PhoneNumber/EmailAddress
UnitedStates Sales 4105 Fieldstone RdChampaign,Illinois,61822USA(800)[email protected]
UnitedKingdom Horizon Hobby LimitedUnits1-4PloytersRdStapleTyeHarlow,Essex,CM187NS,UnitedKingdom
+44(0)[email protected]
Germany HorizonHobbyGmbH Christian-Junge-Straße1 25337Elmshorn,Germany+49 4121 46199 [email protected]
France HorizonHobbySAS14RueGustaveEiffelZoned’ActivitéduRéveilMatin91230Montgeron
+33(0)[email protected]
China Horizon Hobby – China Room 506, No. 97 Changshou Rd. Shanghai,China200060+86(021)51809868 [email protected]
Compliance Information for the European Union
Declaration of Conformity(inaccordancewithISO/IEC17050-1) No.HH2011111301
Product(s): Blade450XBNFItemNumber(s): BLH4380Equipment class: 1
The object of declaration described above is in conformity with the require-ments of the specifications listed below, following the provisions of the EuropeanR&TTEdirective1999/5/ECandEMCDirective2004/108/EC
EN 301 489-1 V1.7.1: 2006EN 301 489-17 V1.3.2: 2008
EN55022: 2006,EN55024: 1998+A1: 2001+A2: 2003
Signedforandonbehalfof:Horizon Hobby, Inc.Champaign,ILUSANovember13,2011
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it istheuser’sresponsibilitytodisposeoftheirwasteequipmentbyhanding it over to a designated collections point for the recy-cling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that
it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
StevenA.Hall VicePresident
InternationalOperationsandRiskManagement Horizon Hobby, Inc.
# Part # English Deutsch Français Italiano
1 BLH4301 FlybarlessLinkageSet:B450X Flybarless-Anlenkgestänge-Set:B450X SetdetringleriesFlybarless :B450X Setgiuntisenzaflybar:B450X
2 BLH4303 MainRotorBladeGripFBLControlBalls(2):B450XFBLHauptrotorblatthalterung- Steuerungskugelköpfe(2)B450X
RotulesdecommandedepiedsdepalesprincipalesFBL(2) :B450X
SferedicontrolloFBLstringipaledelrotoreprincipale(2):B450X
3 BLH4315 CFFBLMainBladeSet325mmwithwashers:B450XCFFBLHauptblatt-Set325mm,mitUnterlagsscheibeB450X
Setdepalesprincipales325mmCFFBLavecrondelles :B450X
SetpaleprincipaliCFFBL325mmconrondelle:B450X
4 BLH4317 FlybarlessMainRotorGripSet:B450X Flybarless-Hauptrotor-Halterungs-Set:B450XSet de pieds de rotor principal Flybarless:B450X
Set stringi pale del rotore principale senzaflybar:B450X
5 BLH4321 FlybarlessSpindleSet(2):B450X Flybarless-Spindel-Set(2):B450X Setd'axesFlybarless(2):B450X Setpernosenzaflybar(2):B450X
6 BLH4322 AluminumFlybarlessHeadBlockSet:B450XAluminium-Flybarless-Rotorkopfblock-Set:B450X
Set de moyeu de tête Flybarless en aluminium:B450X
Setbloccotestasenzaflybarinalluminio:B450X
7 BLH4331 FlybarlessFollowerArms:B450X Flybarless-Tastarme:B450X BrassuiveursFlybarless:B450X Bracciinseguitoresenzaflybar:B450X
8 BLH4338 LinkageRod/PushrodSet:B450X Anlenkgestänge-/Schubstangen-Set:B450XSet de tringleries de traction/pression : B450X Setasta/astadispintadelgiunto:B450X
9 BLH4347 FlybarlessMainShaft(2):B450X Flybarless-Hauptwelle(2):B450X AxeprincipalFlybarless(2) :B450X Alberoprincipalesenzaflybar(2):B450X
10 BLH4381 PhantomCanopy:B450X PhantomCanopy:B450X BulleFantômeB450X CappottinaPhantom:B450X
11 EFLH1115 Bearing3x6x2.5mm(2):B4503D/X,B400Lager3x6x2,5mm(2):B4503D/X,B400
Roulement3x6x2.5mm(2) : B4503D/X,B400
Cuscinetto3x6x2,5mm(2):B4503D/X,B400
12 BLH1603 One-WayBearingHubwithOne-WayBearing:B4503D/XLagernabe für Einweglager mit Einweglager:B4503D/X
Moyeuderouelibre/rouelibre : B4503D/X
Mozzoconcuscinettounidirezionale:B4503D/X
13 BLH1605 4x8x3bearingMainGripandTailshaft(4):B4503D/X4x8x3LagerHaupthalterungundHeckwelle(4):B4503D/X
Roulement4x8x3depiedsdepalesetd'axeanticouple(4) :B4503D/X
Cuscinetto albero principale e albero di coda4x8x3(4):B4503D/X
14 BLH1607 1.5x4x2BearingsWashoutLinks(4):B4503D/X1,5x4x2LagerWashout-Gestänge(4):B4503D/X
Roulementsépaulés1.5x4x2(4):B4503D/X
1,5x4x2cuscinetticollegamentiwashout(4):B4503D/X
15 BLH1608 Dampeners80Deg(4):B4503D/X Dämpfer80Grad(4):B4503D/X Amortisseurs80deg(4) :B4503D/X Smorzatori80gradi(4):B4503D/X
16 BLH1610 PinionGear,10T0.5M:B4503D/X,B400Zahnradgetriebe,10T,0,5m:B4503D/X,B400 Pignon10T0.5M :B4503D/X,B400
Ruotadelpignone,10T0,5M:B4503D/X,B400
17 BLH1612 TailGripThrustBearings:B4503D/X Heckhalterung-Gegenlager:B4503D/XButéesà billesdepieddepaled'anticouple :B4503D/X
Cuscinetti di spinta stringi pale di coda: B4503D/X
18 BLH1613 3x7x3Bearing(2):B4503D/X 3x7x3Lager(2):B4503D/X Roulement3x7x3(2) :B4503D/X 3x7x3cuscinetto(2):B4503D/X
19 BLH1616 MainRotorBladeMountingScrewandNutSet(2):B4503D/X
Set Hauptrotorblatt-BefestigungsschraubenundNuten(2):B4503D/X
Setdevisetd'écroupourpalesprincipales(2) :B4503D/X
Set vite di fissaggio e dado della pala del rotoreprincipale(2):B4503D/X
20 BLH1620 MainGripThrustBearing(2):B4503D/X,B400Haupthalterung-Gegenlager(2):B4503D/X,B400
Butéesà billesdepiedsdepalesprincipales(2) :B4503D/X,B400
Cuscinetto di spinta stringi pala principale(2):B4503D/X,B400
21 BLH1632 WashoutControlArmLinkSet:B4503D/XWashout-Steuerarmgestänge-Set: B4503D/X
Set de tringleries de Washout : B4503D/X
Set collegamento braccio di controllo washout:B4503D/X
22 BLH1633 AluminumandCompositeSwashplate:B4503D/X,B400Aluminium-undVerbundstoff- Taumelscheibe:B4503D/X,B400
Plateau cyclique en aluminium et composite:B4503D/X,B400
Piatto ciclico in alluminio e in composito: B4503D/X,B400
23 BLH1634 Anti-RotationBracketGuide:B4503D/X,B400Anti-Rotations-Bügel/-Führung:B4503D/X,B400
Guide de plateau cyclique : B4503D/X,B400
Staffaguidaanti-rotazione:B4503D/X,B400
24 BLH1635 Control/LinkageBall,Long(4):B4503D/X,B400
Steuerkugelkopf/Kugelkopf Anlenkgestänge,lang(4):B4503D/X,B400
Tringleriesdecommandes,longues(4) :B4503D/X,B400
Comando/sferadelgiunto,lungo(4):B4503D/X,B400
25 BLH1636 Control-LinkageBall,Short(10):B4503D/X,B400
Steuerkugelkopf/Kugelkopf- Anlenkgestänge,kurz(10):B4503D/X,B400
Tringleriesdecommandes,courtes(10) :B4503D/X,B400
Comando/sferadelgiunto,corto(10):B4503D/X,B400
26 BLH1637 BallLinkSet(20):B4503D/X,B400 Kugelkopfpfannen-Set(20):B4503D/X,B400 Setderotules(20) :B4503D/X,B400Setcollegamentosfera(20):B4503D/X,B400
27 BLH1639 MainFrameSet:B4503D/X Hauptrahmen-Set:B4503D/X Châssis :B4503D/X Settelaioprincipale:B4503D/X
28 BLH1640 ElevatorControlLeverSet:B4503D/X,B400Höhenruder-Steuerhebel-Set: B4503D/X,B400
Set de leviers de commande de profondeurB4503D/X,B400
Setlevacomandoelevatore:B4503D/X,B400
29 BLH1641 5x8x2.5BearingElevatorControllever(2):B4503D/X,B4005x8x2,5LagerHöhenruder- Steuerhebel(2):B4503D/X,B400
Roulements5x8x2,5delevierdecommandedeprofondeur(2) : B4503D/X,B400
5x8x2,5cuscinettolevacomandoelevatore(2):B4503D/X,B400
Parts List / Ersatzteile / Pièces de rechange / Pezzi di ricambio
# Part # English Deutsch Français Italiano
1 BLH4301 FlybarlessLinkageSet:B450X Flybarless-Anlenkgestänge-Set:B450X SetdetringleriesFlybarless :B450X Setgiuntisenzaflybar:B450X
2 BLH4303 MainRotorBladeGripFBLControlBalls(2):B450XFBLHauptrotorblatthalterung- Steuerungskugelköpfe(2)B450X
RotulesdecommandedepiedsdepalesprincipalesFBL(2) :B450X
SferedicontrolloFBLstringipaledelrotoreprincipale(2):B450X
3 BLH4315 CFFBLMainBladeSet325mmwithwashers:B450XCFFBLHauptblatt-Set325mm,mitUnterlagsscheibeB450X
Setdepalesprincipales325mmCFFBLavecrondelles :B450X
SetpaleprincipaliCFFBL325mmconrondelle:B450X
4 BLH4317 FlybarlessMainRotorGripSet:B450X Flybarless-Hauptrotor-Halterungs-Set:B450XSet de pieds de rotor principal Flybarless:B450X
Set stringi pale del rotore principale senzaflybar:B450X
5 BLH4321 FlybarlessSpindleSet(2):B450X Flybarless-Spindel-Set(2):B450X Setd'axesFlybarless(2):B450X Setpernosenzaflybar(2):B450X
6 BLH4322 AluminumFlybarlessHeadBlockSet:B450XAluminium-Flybarless-Rotorkopfblock-Set:B450X
Set de moyeu de tête Flybarless en aluminium:B450X
Setbloccotestasenzaflybarinalluminio:B450X
7 BLH4331 FlybarlessFollowerArms:B450X Flybarless-Tastarme:B450X BrassuiveursFlybarless:B450X Bracciinseguitoresenzaflybar:B450X
8 BLH4338 LinkageRod/PushrodSet:B450X Anlenkgestänge-/Schubstangen-Set:B450XSet de tringleries de traction/pression : B450X Setasta/astadispintadelgiunto:B450X
9 BLH4347 FlybarlessMainShaft(2):B450X Flybarless-Hauptwelle(2):B450X AxeprincipalFlybarless(2) :B450X Alberoprincipalesenzaflybar(2):B450X
10 BLH4381 PhantomCanopy:B450X PhantomCanopy:B450X BulleFantômeB450X CappottinaPhantom:B450X
11 EFLH1115 Bearing3x6x2.5mm(2):B4503D/X,B400Lager3x6x2,5mm(2):B4503D/X,B400
Roulement3x6x2.5mm(2) : B4503D/X,B400
Cuscinetto3x6x2,5mm(2):B4503D/X,B400
12 BLH1603 One-WayBearingHubwithOne-WayBearing:B4503D/XLagernabe für Einweglager mit Einweglager:B4503D/X
Moyeuderouelibre/rouelibre : B4503D/X
Mozzoconcuscinettounidirezionale:B4503D/X
13 BLH1605 4x8x3bearingMainGripandTailshaft(4):B4503D/X4x8x3LagerHaupthalterungundHeckwelle(4):B4503D/X
Roulement4x8x3depiedsdepalesetd'axeanticouple(4) :B4503D/X
Cuscinetto albero principale e albero di coda4x8x3(4):B4503D/X
14 BLH1607 1.5x4x2BearingsWashoutLinks(4):B4503D/X1,5x4x2LagerWashout-Gestänge(4):B4503D/X
Roulementsépaulés1.5x4x2(4):B4503D/X
1,5x4x2cuscinetticollegamentiwashout(4):B4503D/X
15 BLH1608 Dampeners80Deg(4):B4503D/X Dämpfer80Grad(4):B4503D/X Amortisseurs80deg(4) :B4503D/X Smorzatori80gradi(4):B4503D/X
16 BLH1610 PinionGear,10T0.5M:B4503D/X,B400Zahnradgetriebe,10T,0,5m:B4503D/X,B400 Pignon10T0.5M :B4503D/X,B400
Ruotadelpignone,10T0,5M:B4503D/X,B400
17 BLH1612 TailGripThrustBearings:B4503D/X Heckhalterung-Gegenlager:B4503D/XButéesà billesdepieddepaled'anticouple :B4503D/X
Cuscinetti di spinta stringi pale di coda: B4503D/X
18 BLH1613 3x7x3Bearing(2):B4503D/X 3x7x3Lager(2):B4503D/X Roulement3x7x3(2) :B4503D/X 3x7x3cuscinetto(2):B4503D/X
19 BLH1616 MainRotorBladeMountingScrewandNutSet(2):B4503D/X
Set Hauptrotorblatt-BefestigungsschraubenundNuten(2):B4503D/X
Setdevisetd'écroupourpalesprincipales(2) :B4503D/X
Set vite di fissaggio e dado della pala del rotoreprincipale(2):B4503D/X
20 BLH1620 MainGripThrustBearing(2):B4503D/X,B400Haupthalterung-Gegenlager(2):B4503D/X,B400
Butéesà billesdepiedsdepalesprincipales(2) :B4503D/X,B400
Cuscinetto di spinta stringi pala principale(2):B4503D/X,B400
21 BLH1632 WashoutControlArmLinkSet:B4503D/XWashout-Steuerarmgestänge-Set: B4503D/X
Set de tringleries de Washout : B4503D/X
Set collegamento braccio di controllo washout:B4503D/X
22 BLH1633 AluminumandCompositeSwashplate:B4503D/X,B400Aluminium-undVerbundstoff- Taumelscheibe:B4503D/X,B400
Plateau cyclique en aluminium et composite:B4503D/X,B400
Piatto ciclico in alluminio e in composito: B4503D/X,B400
23 BLH1634 Anti-RotationBracketGuide:B4503D/X,B400Anti-Rotations-Bügel/-Führung:B4503D/X,B400
Guide de plateau cyclique : B4503D/X,B400
Staffaguidaanti-rotazione:B4503D/X,B400
24 BLH1635 Control/LinkageBall,Long(4):B4503D/X,B400
Steuerkugelkopf/Kugelkopf Anlenkgestänge,lang(4):B4503D/X,B400
Tringleriesdecommandes,longues(4) :B4503D/X,B400
Comando/sferadelgiunto,lungo(4):B4503D/X,B400
25 BLH1636 Control-LinkageBall,Short(10):B4503D/X,B400
Steuerkugelkopf/Kugelkopf- Anlenkgestänge,kurz(10):B4503D/X,B400
Tringleriesdecommandes,courtes(10) :B4503D/X,B400
Comando/sferadelgiunto,corto(10):B4503D/X,B400
26 BLH1637 BallLinkSet(20):B4503D/X,B400 Kugelkopfpfannen-Set(20):B4503D/X,B400 Setderotules(20) :B4503D/X,B400Setcollegamentosfera(20):B4503D/X,B400
27 BLH1639 MainFrameSet:B4503D/X Hauptrahmen-Set:B4503D/X Châssis :B4503D/X Settelaioprincipale:B4503D/X
28 BLH1640 ElevatorControlLeverSet:B4503D/X,B400Höhenruder-Steuerhebel-Set: B4503D/X,B400
Set de leviers de commande de profondeurB4503D/X,B400
Setlevacomandoelevatore:B4503D/X,B400
29 BLH1641 5x8x2.5BearingElevatorControllever(2):B4503D/X,B4005x8x2,5LagerHöhenruder- Steuerhebel(2):B4503D/X,B400
Roulements5x8x2,5delevierdecommandedeprofondeur(2) : B4503D/X,B400
5x8x2,5cuscinettolevacomandoelevatore(2):B4503D/X,B400
Parts List / Ersatzteile / Pièces de rechange / Pezzi di ricambio
# Part # English Deutsch Français Italiano
30 BLH1642 5x10x4BearingsMainShaft(2):B4503D/X,B4005x10x4LagerHauptwelle(2):B4503D/X,B400
Roulements5x10x4d'axeprincipal(2) :B4503D/X,B400
5x10x4cuscinettialberoprincipale(2):B4503D/X,B400
31 BLH1643 AluminumMotorMountSet:B4503D/X,B400Aluminium-Motorbefestigungs-Set:B4503D/X,B400
Set de fixations moteur en aluminium :B4503D/X,B400
Set montante del motore in allumino: B4503D/X,B400
32 BLH1644 Hook&LoopBatteryStrap:B4503D/X,B400(not shown)Akku-KlettverschlussbandB4503D/X,B400(nichtgezeigt)
Sangles crochet et boucle pour ruban adhésifd'accu :B4503D/X,B400(nonreprésenté)
Bandellae ganciodellabatteria:B4503D/X,B400(nonmostrato)
33 BLH1645 LandingGearSet:B4503D/X Fahrwerk-Set:B4503D/X Setdetraind'atterrissage :B4503D/X Setdelcarrellodiatterraggio:B4503D/X
34 BLH1649 One-WayBearingShaftandShimSet:B4503D/X,B400
Set Einweglagerwelle und Unterlagsscheiben:B4503D/X,B400
Axederouelibreetsetderondelles :B4503D/X,B400
Set albero ingranaggio di autorotazione e spessore:B4503D/X,B400
35 BLH1651 MainGear(2):B4503D/X Hauptfahrwerk(2):B4503D/X Couronneprincipale(2) :B4503D/X Ingranaggioprincipale(2):B4503D/X
36 BLH1652 One-WayBearing6x10x12:B4503D/X,B400Einweglager6x10x12:B4503D/X,B400 Rouelibre6x10x12 :B4503D/X,B400
Cuscinettounidirezionale6x10x12:B4503D/X,B400
37 BLH1653 MainTailDriveGear(2):B4503D/X Heckhauptgetriebe(2):B4503D/X Couronned'anticouple(2) :B4503D/X Ingranaggio di trasmissione di coda principale(2):B4503D/X
38 BLH1654 TailDriveShaftLowerBearingBlockMount:B4503D/XBefestigungHeckantriebswelleuntererLagerblock:B4503D/X
Supportderoulementinférieur :B4503D/X
Montantebloccocuscinettoinferioredell'alberoditramissionedicoda:B4503D/X
39 BLH1655 TailDriveGearPulleyAssembly:B4503D/X,B400Heckgetriebe-Riemenscheiben- Anordnung:B4503D/X,B400
Arbred'anticouplepignon/poulie :B4503D/X,B400
Gruppo puleggia ingranaggio di trasmissionedicoda:B4503D/X,B400
40 BLH1656 TailDriveBelt:B4503D/X,B400 AntriebsriemenHeck:B4503D/X,B400 Courroied'anticouple :B4503D/X,B400Cinghiaditrasmissionedicoda:B4503D/X,B400
41 BLH1657 TailBooms(2):B4503D/X Heckausleger(2):B4503D/X Poutredequeue(2) :B4503D/X Astedicoda(2):B4503D/X
42 BLH1658 TailServoBoomMount(2):B4503D/X Servobefestigung Heckausleger (2):B4503D/XFixationdeservod'anticouple(2) :B4503D/X
Montanteastaservodicoda(2):B4503D/X
43 BLH1659 TailLinkagePushrodset(2):B4503D/XAnlenkgestänge-/Schubstangen- SetfürHeck(2):B4503D/X
Tringlerie de commande d'anticouple (2) :B4503D/X
Setastadispintagiuntidicoda(2):B4503D/X
44 BLH1660 TailPushrodSupportGuideSet:B4503D/XHeck-Schubstangen-Stützführung-Set:B4503D/X
Set de guide de commande d'anticouple :B4503D/X
Set guida di sostegno asta di spinta di coda:B4503D/X
45 BLH1661 TailBoomBraceSupportSet(2):B4503D/XHeckauslegerhalterungs/Stützset (2):B4503D/X
Set de renforts et supports de tube de queue(2) :B4503D/X
Setsostegnobraccioastadicoda(2):B4503D/X
46 BLH1662 HorizontalStabilizerFinMount:B4503D/XBefestigunghorizontale Stabilisierungsflosse:B4503D/X
Fixationdedériveetstabilisateur :B4503D/X
Montaggioderivadistabilizzazioneorizzontale:B4503D/X
47 BLH1663 TailCaseSet:B4503D/X Heckabdeckungs-Set:B4503D/X Setdeboîtierd'anticoupleB4503D/X Setcasecoda:B4503D/X
48 BLH1665 TailRotorShaftandDrivePulley(2):B4503D/XWelleundAntriebsscheibeHeckrotor(2):B4503D/X
Axeetpouliederotord'anticouple(2) :B4503D/X
Alberorotoredicodae puleggiaditrasmissione(2):B4503D/X
49 BLH1666 2x5x2.5Bearing:B450,B400 2x5x2,5Lager:B450,B400 Roulement2x5x2.5 :B450,B400 2x5x2,5cuscinetto:B450,B400
50 BLH1667 TailRotorPitchLeverSet:B4503D/X Heckrotor-Pitchhebel-Set:B4503D/XSetdelevierdepasd'anticouple :B4503D/X
Setlevapitchdelrotoredicoda:B4503D/X
51 BLH1668 TailRotorPitchControlSliderSet:B4503D/XHeckrotor-Pitchschieberegler-Set: B4503D/X Setdesliderd'anticouple :B4503D/X
Set cursore comando passo rotore di coda:B4503D/X
52 BLH1669 TailRotorHubSet:B4503D/X Heckrotornaben-Set:B4503D/X Moyeud'anticouple :B4503D/X Setmozzorotoredicoda:B4503D/X
53 BLH1670 TailRotorBladeGripHolderSet:B4503D/XHeckrotorblatthalterungs-Set: B4503D/X
Set de pieds de pales d'anticouple : B4503D/X
Set sostegno stringi pala rotore di coda: B4503D/X
54 BLH1671 TailRotorBladeSet:B4503D/X Heckrotorblatt-Set:B4503D/X Setdepalesd'anticouple :B4503D/X Setpaledelrotoredicoda:B4503D/X
55 BLH1672 StabilizerFinSetWhite:B4503D/X Stabilisierungsflossen-Set,weiß: B4503D/XSetDérive/stabilisateur,blanc:B4503D/X
Set deriva di stabilizzazione bianca: B4503D/X
56 BLH1673 CompleteHardwareSet:B4503D/X KomplettesHardware-Set:B4503D/X Setdevisserie :B4503D/X Setcompletohardware:B4503D/X
57 BLH1674MountingAccesssories,Screwdriver&Wrench:B4503D/X,B400 (not shown)
Befestigungszubehör,Schraubenzieher&Schraubenschlüssel:B4503D/X,B400 (nichtgezeigt)
Setd'outilstournevisetclés :B4503D/X,B400(nonreprésenté)
Accesssorimontaggio,cacciavitee chiave:B4503D/X,B400 (nonmostrato)
58 BLH1676 ServoArmSet:B4503D/X,B400 Servoarm-Set:B4503D/X,B400 Setdebrasdeservos :B4503D/X,B400 Setbracciodelservo:B4503D/X,B400
Part # English Deutsch Français Italiano
BLH4302 FlybarlessSetupTool:B450X Flybarless-Setupwerkzeug.B450X OutilderéglageFlybarless :B450X Attrezzosetupsenzaflybar:B450X
BLH4317A AluminumFlybarlessMainRotorGripSet:B450XAluminium-Flybarless- Hauptrotorhalterungs-Set:B450X
Set de pieds de rotor principal Flybarlessenaluminium :B450X
Set stringi pale del rotore principalesenzaflybarinalluminio:B450X
BLH4331A AluminumFlybarlessFollowerArms:B450X Aluminium-Flybarless-Tastarme:B450XBrassuiveursFlybarlessenaluminium :B450X
Bracciinseguitoresenzaflybar:B450X
BLH4381A SmokeyCanopy:B450X SmokeyCanopy:B450X BulleSmokey :B450X Calottinagrigia:B450X
BLH1609 PinionGear,9T0.5M:B4503D/X,B400 Zahnradgetriebe,9T,0,5m:B4503D/X,B400 Pignon,9T0.5M :B4503D/X,B400Ruotaconica,9T0,5M:B4503D/X,B400
BLH1611 PinionGear,11T0.5M:B4503D/X,B400Zahnradgetriebe,11T,0,5m:B4503D/X,B400 Pignon,11T0.5M :B4503D/X,B400
Ruotadelpignone,11T0,5M:B4503D/X,B400
BLH1633A AluminumSwashplate:B4503D/X,B400Aluminium-Taumelscheibe:B4503D/X,B400
Plateaucycliqueenaluminium :B4503D/X,B400
Piattociclicoinalluminio:B4503D/X,B400
BLH1634A AluminumAnti-RotationBracket/Guide:B4503D/X,B400Aluminium-Anti-Rotations-Bügel/-Führung:B4503D/X,B400
Guide de plateau cyclique en aluminium : B4503D/X,B400
Staffa/guida anti-rotazione in alluminio:B4503D/X,B400
BLH1645B LandingGearSet,Black:B4503D/X Fahrwerk-Set,schwarz:B4503D/X Jeudetraind'atterrissage,Noir :B4503D/X Set del carrello di atterraggio, nero:B4503D/X
BLH1654A AlumTailDriveShaftLowerBearBlck:B4503D/X,B400
AluminiumbefestigungHeckantriebswelle unterer Lagerblock: B4503D/X,B400
Palierinférieurd'arbred'anticouple enaluminium,Noir :B4503D/X,B400
Bloccocuscinettoinferiorealberotrasmissione di coda in alluminio: B4503D/X,B400
BLH1655A AluminumTailDriveGearPulleyAssy:B4503D/X,B400
Aluminium-Heckgetriebe- Riemenscheiben-Anordnung: B4503D/X,B400
Arbrepignon/poulietransmissiond'anticouplealuminiumB4503D/X,B400
Assepuleggiaingranaggioditrasmissione di coda in alluminio: B4503D/X,B400
BLH1657C CarbonFiberTailBoom:B4503D/X Karbonfaser-Heckausleger:B4503D/X Poutreencarbone:B4503D/X Astadicodainfibradicarbonio:B4503D/X
BLH1658A AluminumTailServoBoomMount:B4503D/X,B400Aluminium-Servobefestigung Heckausleger:B4503D/X,B400
Support de servo d'anticouple en aluminium B4503D/X,B400
Montanteastadelservodicodainalluminio:B4503D/X,B400
BLH1661A TailBoomBrace/SupportSet/AluminumE:B4503D/XHeckauslegerhalterung/Stützset/ AluminiumE:B4503D/X
Set de renforts et support de poutre enaluminiumE :B4503D/X
Sostegno asta della coda/set supporto/alluminioE:B4503D/X
BLH1662A AluminumHorizontalStabFinMount:B4503D/XAluminium-BefestigunghorizontaleStabilisierungsflosse:B4503D/X
Supportdedériveetstabilisateur enaluminium :B4503D/X
Montantederivastabilizzazioneorizzontaleinalluminio:B4503D/X
BLH1663A AluminumTailCaseSet:B4503D/X Aluminium-Heckabdeckungs-Set: B4503D/XSet de boîtier d'anticouple enaluminiumB4503D/X
Setcasecodainalluminio:B4503D/X
Optional Parts / Optionale Bauteile / Pièces optionnelles / Pezzi opzionali
# Part # English Deutsch Français Italiano
59 BLH1679 CanopyMounts(2):B4503D/X Canopy-Befestigungselemente(2):B4503D/X Fixationsdebulle(2) :B4503D/XStaffedimontaggiocalottina(2):B4503D/X
60 SPMAR 7200BX SpektrumAR7200BX SpektrumAR7200BX SpektrumAR7200BX SpektrumAR7200BX
61 EFLRDS76 7.6-GramSub-MicroDigitalServo(ELE/AIL/PIT)7,6-Gramm-Sub-Micro-Digitalservo(NICK/ROLL/PITCH)
ServonumériqueSubMicro7.6 g(ELE/AIL/PIT)
7,6grammiservodigitaleSub-Micro(ELE/AIL/PIT)
62 EFLRDS76T 7.6-GramSub-MicroDigitalServo-TR 7,6-Gramm-Sub-Micro- Digitalservo-TR ServonumériqueSubMicro7.6 g(TR)7,6grammiservodigitaleSub-Micro-TR
63 EFLA335H 35AProS-BECBrushlessESC 35AProS-BECBrushless-ESC CEVBrushlessProS-BEC35A 35AProS-BECBrushlessESC
64 EFLB 22003S302200mAh3S11.1V30CLiPo13AWGEC3(not shown)
2200mAh3S11,1V30CLiPo13AWGEC3(nichtgezeigt)
Li-Po11,1V 2200mAh3S30C13AWGEC3(nonreprésentée)
2200mAh3S11,1V 30CLiPo13AWGEC3(nonmostrato)
65 BLH1001 MiniHelicopterMainBladeHolder(not shown)Mini-Helikopter-Hauptblatt-Halterung(nichtgezeigt)
SupportdepalesprincipalesHélico(nonreprésenté)
SupportopalaprincipaleMinielicottero(nonmostrato)
66 EFLC3115 3S11.1VLiPoBalancingCharger,1.8A(not shown)3S11,1VLiPo-Balancer-Ladegerät, 1,8A(nichtgezeigt)
Chargeur-équilibreurLi-Po11,1V,1,8 A 3S(nonreprésenté))
3S11,1V LiPocaricabatterieconbilanciatore,1,8A (nonmostrato)
67 EFLM1360H Brushless440HelicopterMotor,4200KvBrushless440Helikoptermotor, 4200KV
Moteurd'hélicoptèreBrushless440,4200Kv Motorebrushlesselicottero440,4200KV
68 SPMA3031 PotAdjustmentTool:AR7200BX VerstellwerkzeugPotentiometer:AR7200BXOutilderéglagedepotentiomètre :AR7200BX
Attrezzoregolazionepotenziometro:AR7200BX
Parts List / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Optional Parts / Optionale Bauteile / Pièces optionnelles / Pezzi opzionali
Part # English Deutsch Français Italiano
BLH1665A TailRotorShaftAluminumDrivePulley:B4503D/XWelleundAntriebsscheibeHeckrotor,Aluminium(2):B4503D/X
Axed'anticoupleetpouliealuminium :B4503D/X
Puleggia trasmissione in alluminio dell'albero del rotore di coda:B4503D/X
BLH1667A AluminumTailRotorPitchLeverSet:B4503D/XAluminium-Heckrotor-Pitchhebel-Set:B4503D/X
Levier de pas d'anticouple enaluminium :B4503D/X
Set leva del pitch del rotore di codainalluminio:B4503D/X
BLH1668A AluminumTailRotorPitchControlSliderSet:B4503D/XAluminium-Heckrotor- Pitchschieberegler-Set:B4503D/X
Set de slider d'anticouple enaluminium :B4503D/X
Set cursore comando passo rotoredicodainalluminio:B4503D/X
BLH1670A AluminumTailRotorBladeGrpSet:B4503D/XAluminium-Heckrotorblatt-Set: B4503D/X
Pieds de pales d'anticouple enaluminium :B4503D/X
Set stringi pala rotore di coda in alluminio:B4503D/X
BLH1671B TailRotorBladeSet,Black:B4503D/X Heckrotorblatt-Set,schwarz:B4503D/X Setdepalesd'anticouple,Noir :B4503D/X Set pale del rotore di coda, nero: B4503D/X
BLH1671C TailRotorBladeSetCarbonFiber:B4503D/X,B400Heckrotorblatt-Set, Karbonfaser: B4503D/X,B400
Setdepalesd'anticoupleencarbone :B4503D/X,B400
Set in fibra di carbonio delle pale delrotoredicoda:B4503D/X,B400
BLH1672B Stab/FinSet,Black:B4503D/X Stabilisator/Flossen-Set, schwarz: B4503D/X Setdestabilisateur/dérive,Noir :B4503D/X Setstab/der,nero:B4503D/X
BLH1672C Stab/FinSet,CarbonFiber:B4503D/X Stabilisator/Flossen-Set, Karbonfaser: B4503D/XSetdestabilisateur/dériveencarbone :B4503D/X
Set stab/der, fibra di carbonio: B4503D/X
BLH1676A AluminumServoControlArms:B4503D/X,B400Aluminium-Servosteuerarme: B4503D/X,B400
Brasdeservosenaluminium :B4503D/X,B400
Braccicomandiservoinalluminio:B4503D/X,B400
BLH1679A AluminumCanopyMounts:B4503D/X Aluminium-Canopy- Befestigungselemente:B4503D/X Supportsdebulleenaluminium :B4503D/XMontanticalottinainalluminio:B4503D/X
BLH1690A SwashLevelingTool:B4503D/X,B400 Taumelscheibe-Nivellierungswerkzeug B4503D/X,B400OutilderéglagedeplateaucycliqueB4503D/X,B400
Strumento di livellamento del piattociclico:B4503D/X,B400
BLH4399 Aluminum450FlybarlessConversionSet:B4503DAluminium-450Flybarless- Umrüstungs-Set:B4503D
Setdeconversion450Flybarlessenaluminium :B4503D
Setconversionesenzaflybar450inalluminio:B4503D
BLH1671OR TailRotorBladeSet,Orange:B4503D/X,B400Heckrotorblatt-Set,orange:B4503D/X,B400
Setdepalesd'anticouple,Orange :B4503D/X,B400
Set pale del rotore di coda, arancione:B4503D/X,B400
BLH1671YE TailRotorBladeSet,Yellow:B4503D/X,B400Heckrotorblatt-Set,gelb:B4503D/X,B400
Setdepalesd'anticouple,Jaune :B4503D/X,B400
Set pale del rotore di coda, giallo: B4503D/X,B400
BLH1671GR TailRotorBladeSet,Green:B4503D/X,B400Heckrotorblatt-Set,grün:B4503D/X,B400
Setdepalesd'anticouple,Vert :B4503D/X,B400
Set pale del rotore di coda, verde:B4503D/X,B400
BLH1699 450CarryingCase 450Tragekoffer Coffretdetransport450 Valigettaperiltrasporto450
EFLC 3025
Celectra80WAC/DCMulti-ChemistryBatteryCharger
Celectra80WAC/DCMulti- Chemistry-Batterieladegerät
Chargeur de batterie multi-types Celectra80 W CA/CC
Caricabatterie per batteria multichimica80W a.c.=c.c.
EFLC 3025AU
Celectra80WAC/DCMulti-ChemistryBatteryCharger(Australia)
Celectra80WAC/DCMulti- Chemistry-Batterieladegerät(Australien)
Chargeur de batterie multi-types Celectra80 W CA/CC(Australie)
Caricabatterie per batteria multichimica80W a.c=c.c.(Australia)
EFLC 3025EU
Celectra80WAC/DCMulti-ChemistryBatteryCharger(Europe)
Celectra80WAC/DCMulti- Chemistry-Batterieladegerät(Europa)
Chargeur de batterie multi-types Celectra80 W CA/CC(Europe)
Caricabatterie per batteria multichimica80W a.c=c.c.(Europa)
EFLC 3025UK
Celectra80WAC/DCMulti-ChemistryBatteryCharger(UnitedKingdom)
Celectra80WAC/DCMulti- Chemistry-Batterieladegerät(GB)
Chargeur de batterie multi-types Celectra80 W CA/CC(RoyaumeUni)
Caricabatterie per batteria multichimica80W a.c=c.c.(RegnoUnito)
EFLC4030 3.0-AmpPowerSupply,100-240VAC-12VDC3,0-Amp-Netzstecker, 100-240VAC-12VDC
Alimentation3,0A ,100-240 V CA-12 V CC
Alimentatore3,0Amp,100-240V a.c.12V c.c.
EFLC 4030
3.0-AmpPowerSupply,100-240VAC-12VDC
3,0-Amp-Netzstecker, 100-240VAC-12VDC
Alimentation3,0A ,100-240 V CA-12 V CC
Alimentatore3,0Amp,100-240V a.c.12V c.c.
EFLC 4030EU
3.0-AmpPowerSupply,100-240VAC-12VDC(Europe)
3,0-Amp-Netzstecker, 100-240VAC-12VDC(Europa)
Alimentation3,0A ,100-240 V CA-12 V CC(Europe)
Alimentatore3.0Amp,100-240V a.c.12V c.c.
EFLC 4030UK
3.0-AmpPowerSupply,100-240VAC-12VDC(UnitedKingdom)
3,0-Amp-Netzstecker, 100-240VAC-12VDC(GB)
Alimentation3,0A ,100-240 V CA-12 V CC(RoyaumeUni)
Alimentatore3.0Amp,100-240V a.c.12V c.c.(RegnoUnito)
EFLC 4030AU
3.0-AmpPowerSupply,100-240VAC-12VDC(Australia)
3,0-Amp-Netzstecker, 100-240VAC-12VDC(Australien)
Alimentation3,0A ,100-240 V CA-12 V CC(Autralie)
Alimentatore3.0Amp,100-240V a.c.12V c.c.(Australia)
DX8DSMXTransmitterOnly DX8DSMXNurSender ÉmetteurDX8DSMXseul SolotrasmettitoreDSMXDX8
DX7s7ChwithAR8000NoSX’s DX7s7LadegerätmitAR8000KeineSXs DX7s7voiesavecAR8000sansservosDX7s7canaliconAR8000senzaSX
DX6iDSMX6-ChannelTransmitterOnly NurDX6iDSMX6-Kanal-Sender ÉmetteurDX6iDSMX6voiesseul DX6iDSMX6canalisenzatrasmettitore
3
9
22
2149
2013
19
26
19
54
155
54
44
2
2
113
13
131919
208
7
76
14
3
15
6
42
62
45
40
43
41
55
46
47
55
47
13
48
4644
4747
50
11
50
545217
17
1111
53
5211
5353
53
51
54
52
10
64
63
27
60
38
59
582626
61
8
26
26
33
18
18
39
30
34
34
37
31
67
16
12
36
28
29
35
27
23
2330
61
61
58
58 28
8
26
26
26
27
8
859
©2011 Horizon Hobby, Inc. Blade,DSM,DSM2,ModelMatch,AirWareandEC3aretrademarksorregisteredtrademarksofHorizonHobby,Inc. DSMXisatrademarkofHorizonHobby,Inc.,registeredintheU.S. TheSpektrumtrademarkisusedwithpermissionofBachmannIndustries,Inc. BeastXisatrademarkofMarkusSchaackandisusedwithpermission.TheSpektrumAR7200BXemploystechnologyexclusivelylicensedtoHorizonHobby,Inc.from freakware GmbH. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan USpatentnumber7,391,320.Otherpatentspending. Created10/1132111BLH4380