120 Deeds Drive, Dover, OH 44622Phone: 330-343-4283 | Fax: 330-602-3400
www.alliedmachine.com
Solution Number Solution Name Allied Rep
S-4500001-21-4 Rev. 0(This number is for reference only. Please use product item
numbers when ordering.)
Engineered Solution Chad SchmidtEastern RegionPhone: 570-396-3802Fax: 330-602-3400Email: [email protected] For
Joe Cordasco at Tool-Krib Supply Co.
Prepared By
Brittney Masters
Distributor Customer
Tool-Krib Supply Co.787 Passaic AvenueWest Caldwell, NJ 07006Phone: 973-808-4550Fax: 973-808-4544Attn: Joe CordascoEmail: [email protected]
New Prospect Opp for TOOL-KRIB SUPPLY.....................................................................................................................................................................................2-6
Contents
New Prospect Opp for TOOL-KRIB SUPPLY CO. (Madsen) on...Item Breakdown
*See following pages for engineered specials information, including quantity price break points.
Please respond within 2 days. AMEC deliveries allow 2 days for drawing review. Responses longer than 2 days will impact quoted delivery dates.**See full item break down below for quantity sensitive items.
NOTE: Non-stocked items are NON-RETURNABLE. They are also subject to PROCESS FEES. Process fees are added into the list price shown in this document.
NOTE: Images depicted in this solution may not represent the actual product involved. Some images are general product images to be used as a reference ONLY.
Please look for a quote from your distributor with regards to pricing.
ID Image Item Number System Description Unit Weight Pkg QTY Min. Order QTY QTY Availability QTY Sensitive
1 211015-570 Rev. 0* 1.5000" Diameter #3 Series T‐A® Flat Bottom Insert... TBD 2 2 2 10 Work Days Yes
2
25030S-125L #3 TA EXT HLDR 1-1/4"SS 5.35 lbs 1 1 1 In Stock No
COMMENTS: Long Drill for 211015-570
3
22030S-125L #3 TA SHT HLDR 1-1/4"SS 3.44 lbs 1 1 1 In Stock No
COMMENTS: Pilot Drill for 211015-570
4 211015-571 Rev. 0* 2.5000" Diameter #5 Series T‐A® Flat Bottom Insert... TBD 1 1 1 30 Work Days Yes
5
24050S-200L #5 TA STD HLDR 2" SS 17.5 lbs 1 1 1 In Stock No
COMMENTS: Drill for 211015-571
General Notes
Order QTYVarianceAmount *Deviations with approval by the customer Allowable Shipment Quantity Variance Table
*Applies to Non-Stock Standards only
All special order cancellations are subject to minimum of 10% cancellation charge. AMEC reserves the right to increasethe cancellation charge as deemed necessary to cover costs associated with items being cancelled. ‐ Prices & delivery subject to change without notice. ‐ Stock is subject to prior sales. ‐ Shipment lead time starts upon receipt of order.
For questions or to place an order, email Inside Sales at [email protected] or call 330-343-4283.
1-9 +0/-0
10-49 +0/-1
50-149 +0/-2
150-299 +0/-3
300-499 +0/-5
500+ +0/-10
Allied Machine & Engineering | Tool‐Krib Supply Co. | S‐4500001‐21‐4 10/15/2021 3:25 PM | Page 2 of 6
New Prospect Opp for TOOL-KRIB SUPPLY CO. (Madsen) on 2021-10-15Engineered Special Description
System Description Additional Notes / Description QTY Availability
1.5000" Diameter #3 Series T‐A® Flat Bottom Insert MadeFrom Super Cobalt With TiCN Coating, Standard Lip
Geometry, Standard Chipbreakers, 0.0300" Corner Radius, PerAMEC# 211015-570 Rev. 0
For additional opportunities to lower cost, please reviewAMEC's Blanket Release Order Policy (BRO Policy 081618 Rev.
3).
2 10 Work Days
3 10 Work Days
4 10 Work Days
5-9 10 Work Days
10-19 10 Work Days
20-49 10 Work Days
50-99 10 Work Days
100-249 10 Work Days
250+ 10 Work Days
This quotation is being offered based on the information that has been provided to AMEC. The price and manufactuability is subject to change based on the final design of the item.
Please respond within 2 days. AMEC deliveries allow 2 days for drawing review. Responses longer than 2 days will impact quoted delivery dates.
Order QTYVarianceAmount This Document will serve as our offical response. Please notify us if additional copies should be
mailed. ‐ This quote is valid until 12/31/2022 unless you are sent a specific notification to the contrary. ‐ Scheduled lead time is based on availability of material at time of order. You will be notified within 3 business days of receipt of order, if a lead time change is required. ‐ Scheduled lead time starts upon receipt of order as well as customer approved AMEC drawing when appropriate. ‐ All special order cancellations are subject to a minimum of 10% cancellation charge. AMEC reserves the right to increase the cancellation charge as deemed necessary to cover costs associated with items being canceled.ALLIED MACHINE & ENGINEERING CORPThis quote prepared by: Application Engineering
1-9 +0/-0
10-49 +0/-1
50-149 +0/-2
150-299 +0/-3
300-499 +0/-5
500+ +0/-10
Allied Machine & Engineering | Tool‐Krib Supply Co. | S‐4500001‐21‐4 10/15/2021 3:25 PM | Page 3 of 6
New Prospect Opp for TOOL-KRIB SUPPLY CO. (Madsen) on 2021-10-15Tool Drawing - 211015-570
General Notes
Allied Machine & Engineering | Tool‐Krib Supply Co. | S‐4500001‐21‐4 10/15/2021 3:25 PM | Page 4 of 6
New Prospect Opp for TOOL-KRIB SUPPLY CO. (Madsen) on 2021-10-15Engineered Special Description
System Description Additional Notes / Description QTY Availability
2.5000" Diameter #5 Series T‐A® Flat Bottom Insert MadeFrom Super Cobalt With TiCN Coating, Standard Lip
Geometry, Standard Chipbreakers, 0.0300" Corner Radius, PerAMEC# 211015-571 Rev. 0
For additional opportunities to lower cost, please reviewAMEC's Blanket Release Order Policy (BRO Policy 081618 Rev.
3).
1 30 Work Days
2 30 Work Days
3 30 Work Days
4 30 Work Days
5-9 30 Work Days
10-19 30 Work Days
20-49 30 Work Days
50-99 30 Work Days
100-249 30 Work Days
250+ 30 Work Days
This quotation is being offered based on the information that has been provided to AMEC. The price and manufactuability is subject to change based on the final design of the item.
Please respond within 2 days. AMEC deliveries allow 2 days for drawing review. Responses longer than 2 days will impact quoted delivery dates.
Order QTYVarianceAmount This Document will serve as our offical response. Please notify us if additional copies should be
mailed. ‐ This quote is valid until 12/31/2022 unless you are sent a specific notification to the contrary. ‐ Scheduled lead time is based on availability of material at time of order. You will be notified within 3 business days of receipt of order, if a lead time change is required. ‐ Scheduled lead time starts upon receipt of order as well as customer approved AMEC drawing when appropriate. ‐ All special order cancellations are subject to a minimum of 10% cancellation charge. AMEC reserves the right to increase the cancellation charge as deemed necessary to cover costs associated with items being canceled.ALLIED MACHINE & ENGINEERING CORPThis quote prepared by: Application Engineering
1-9 +0/-0
10-49 +0/-1
50-149 +0/-2
150-299 +0/-3
300-499 +0/-5
500+ +0/-10
Allied Machine & Engineering | Tool‐Krib Supply Co. | S‐4500001‐21‐4 10/15/2021 3:25 PM | Page 5 of 6
New Prospect Opp for TOOL-KRIB SUPPLY CO. (Madsen) on 2021-10-15Tool Drawing - 211015-571
General Notes
Allied Machine & Engineering | Tool‐Krib Supply Co. | S‐4500001‐21‐4 10/15/2021 3:25 PM | Page 6 of 6
BORING REAMING BURNISHING THREADING SPECIALSDRILLING
www.alliedmachine.com
North America Europe AsiaAllied Machine Allied Machine Allied Machine Europe Wohlhaupter™ India
120 Deeds DriveDover, OH 44622
United States
485 West 3rd StreetDover, OH 44622
United States
93 Vantage PointPensnett EstateKingswinford
West MidlandsDY6 7FR, United Kingdom
B-23, 2nd FloorB Block Community Centre
Janakpuri, New Delhi - 110058India
ThreadMills USA™ Superion® Wohlhaupter™ GmbH4185 Crosstowne Ct #B
Evans, GA 30809United States
1285 S Patton St.Xenia, OH 45385
United States
Maybachstrasse 4Postfach 1264
72636 FrickenhausenGermany
Allied Machine & Engineering is a worldwide leader in holemaking and finishing solutions. We are committed to providing practical and dependable solutions to our customers through innovative designs and superior customer and technical support.
We continue to expand our product offering in order to provide new and different solutions. With Field Sales Engineers located around the world, we position ourselves to provide technical support on site, right at your spindle.
WE LOOK FORWARDTO WORKING WITH YOU ON YOUR ENGINEERED SOLUTION.
Copyright © 2021 Allied Machine and Engineering Corp.– All rights reserved.