PR201 (MS-1223)Disassemble SOP
■ 1、Battery Pack
■ 2、BOTTOM DOOR ASSY
■ 3、THERMAL-KIT And CPU Module
■ 4、WLAN、MDC And RAM Module
■ 5、HDD Module ASSY
■ 6、ODD Module ASSY
■ 7、HINGE COVER ASSY
■ 8、UP CASE ASSY
■ 9、LOWER CASE ASSY
■ 10、LCD MODULE ASSY
PR201(MS-1223)Disassemble SOP
■ 1、Battery Pack 1-1:According to the direction of the arrow to Push the battery Unlock button shown below;
1-2:Push the battery Release button in the direction shown below, then slide the battery pack remove of the slot;
NO. Part Name Part No. Qty
1 Battery Pack S9N-0182210-W38 1
PR201(MS-1223)Disassemble SOP
■ 2、BOTTOM DOOR ASSY
2-1:Use Screw Driver to remove 5pcs M2.5*5mm screws on the Bottom Door.
Note:Screw driver torque is 1.8~2.2kgf.cm
2-2:Remove Bottom Door in the direction as below;
NO. Part Name Part No. Qty
1 Screw E43-1250551-H29 5
2 BOTTOM DOOR ASSY 307-221J212-W28 1
PR201(MS-1223)Disassemble SOP
■ 3、THERMAL-KIT And CPU Module 3-1:Remove 3pcs M2*6MM screws, Then RemoveCPU Fan sink Cable and 4pcs M2.5*5 screws in the direction shown below;.
Note:CPU Thermal Module Screw driver torque is 2.0~2.5kgf.cm(1-4)
Note:CPU FAN Screw driver torque is 1.5~2.0kgf.cm(1-3)
3
2
4
1
3
1
2
Cable
NO. Part Name Part No. Qty
1 screw E43-1206001-H29 3
2 screw E43-I250551-H29 4
PR201(MS-1223)Disassemble SOP
3-2:Remove CPU Fan sink,Then Remove CPU Thermal Module in the direction as below;
NO. Part Name Part No. Qty
1 CPU FAN E33-0900212-F05 1
2 CPU Thermal Module E31-0800311-F05 1
PR201(MS-1223)Disassemble SOP
3-3:Let the CPU Slot open with Screw Driver;
3-4:Remove CPU Module in the direction as below;
NO. Part Name Part No. Qty
1 CPU Module A09-2520106-I06 1
PR201(MS-1223)Disassemble SOP
■ 4、WLAN、MDC And RAM Module
4-1:Remove 1pcs M2*3mm screw,Then Remove ANTENNA/HIGH-TEK/R-L in the direction shown below;
Note:Screw driver torque is 1.5~2.0kgf.cm
4-2:Remove WIRELESS CARD in the direction shown below;
NO. Part Name Part No. Qty
1 WIRELESS CARD S57-0800180-I06 1
2 Screw E43-1203003-H29 1
PR201(MS-1223)Disassemble SOP
4-3:Remove 2pcs M2*L3mm screws, Then Remove MDC Cable in the direction shown below;
Note:Screw driver torque is 1.5~2.0kgf.cm
1
2
4-4:Remove MODEM in the direction shown below;
NO. Part Name Part No. Qty
1 MODEM S52-2801180-C59 1
2 Screw E43-1203003-H29 2
3 MDC Cable K10-3002094-H58 1
PR201(MS-1223)Disassemble SOP
4-5:Push the RAM locks away;
4-6:Remove the RAM Module as below:
NO. Part Name Part No. Qty
1 RAM Module S7C-S346703-T10 1
R201(MS-1223)Disassemble SOP
■ 5、HDD Module ASSY 5-1:Remove 2pcs M2.5*5mm screws and HDD Module in the direction shown below;
Note:Screw driver torque is 1.8~2.2kgf.cm
1
2
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 2
PR201(MS-1223)Disassemble SOP
5-2:Remove 2pcs M3*3.5mm Screws, Then Remove HDD Bracket in the direction shown below;
Note:Screw driver torque is 1.5~2.0kgf.cm
2
1
NO. Part Name Part No. Qty
1 Screw E43-1303501-H29 2
2 HDD Bracket Assy E2M-2211511-Y28 1
3 HDD MODULE ASSY S71-2416504-T14 1
PR201(MS-1223)Disassemble SOP
■ 6、ODD Module ASSY 6-1:Remove ODD Module in the direction shown below;
PR201(MS-1223)Disassemble SOP
6-2:Remove ODD Bezel in the direction shown below;
NO. Part Name Part No. Qty
1 ODD Bezel 307-221F212-Y31 1
PR201(MS-1223)Disassemble SOP 6-3:Remove 2pcs M2*3mm Screws,then remove ODD Bracket in the direction shown below;
Note:Screw driver torque is 1.5~1.8kgf.cm
1 2
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 2
2 ODD Side Bracket E2M-2211611-Y28 1
3 ODD MODULE ASSY S7D-2270002-P87 1
PR201(MS-1223)Disassemble SOP
■ 7、HINGE COVER ASSY 7-1:Attention: Battery slot Of 3pcs card;
2 1 3
7-2:Unlock the hooks of both sides;
PR201(MS-1223)Disassemble SOP
7-3:Remove LCD LVDS Cable、CAMERA CABLE, Then Remove Inverter Cable in the direction shown below;
7-4:Remove MICROPHONE CABLE 、Speaker CABLE, Then Remove BLUETOOTH CABLE in the direction shown
below;
NO. Part Name Part No. Qty
1 INVERTER Cable K1H-3006006-H39 1
2 Camera Cable K10-3004096-H58 1
3 LCD LVDS Cable K19-3020014-H58 1
4 BLUETOOTH CABLE K10-3008063-H58 1
PR201(MS-1223)Disassemble SOP 7-5:Pull out cable from the slot in the direction as below;
PR201(MS-1223)Disassemble SOP
7-6:Remove 2pcs M2.5*5mm screws in the direction shown below;
Note:Screw driver torque is 1.8~2.2kgf.cm
2
1
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 2
PR201(MS-1223)Disassemble SOP
7-7:Remove LCD MODULE ASSY in the direction shown below;
PR201(MS-1223)Disassemble SOP
■ 8、UPCASE ASSY
8-1:Remove 4pcs Middle Shielding Cover in the direction as below;
1 2 3 4
NO. Part Name Part No. Qty
1 Middle Shielding Cover E2M-2211012-H48 4
PR201(MS-1223)Disassemble SOP
8-2:Remove Keyboard in the direction as below;
8-3:Remove Keyboard Cable in the direction as below;
NO. Part Name Part No. Qty
1 Keyboard S1N-1UUS231-C54 1
PR201(MS-1223)Disassemble SOP
8-4:Remove 6pcs M2.5*5mm Screws in the direction as below;
Note:Screw driver torque is 1.8~2.2kgf.cm
2
3
4
5
1
6
NO. Part Name Part No. Qty
1 Screws E43-I250551-H29 6
PR201(MS-1223)Disassemble SOP
8-5:Remove SIM Card Door in the direction as below;
NO. Part Name Part No. Qty
1 SIM CARD DOOR E2P-2210211-Y31 1
PR201(MS-1223)Disassemble SOP
8-6:Remove 3pcs M2*3mm Screws in the direction as below;
Note:Screw driver torque is 1.2~1.5kgf.cm
3
2
1
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 3
PR201(MS-1223)Disassemble SOP
8-7:Remove PCI-EXPRESS DUMMY CARD, Then Remove SD DUMMY CARD in the direction as below;
NO. Part Name Part No. Qty
1 PCI-EXPRESS DUMMY CARD E2P-2212814-H76 1
2 SD DUMMY CARD E2P-2212711-H76 1
PR201(MS-1223)Disassemble SOP
8-8:Remove Touchpad FFC (To M/B) ,Then Remove Launch Board Cable in the direction as below;
8-9:Remove 2pcs M2*3.5mm Screws, Then Remove Launch Board in the direction as below;
Note:Screw driver torque is 1.5~1.8kgf.cm
2 1
PR201(MS-1223)Disassemble SOP
8-10:Remove Launch Board Cable;
NO. Part Name Part No. Qty
1 Screw E43-1203501-H29 2
2 Launch Board 607-1331A-01S 1
3 Launch Board Cable K1C-1020002-J36 1
PR201(MS-1223)Disassemble SOP 8-11:Remove 4pcs M2*3mm Screws, Then Remove SPEAKER_SHIELDING in the direction as below;
Note:Screw driver torque is 1.5~18kgf.cm
1 2 3 4
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 4
2 SPEAKER_SHIELDING E2M-2210911-Y28 2
PR201(MS-1223)Disassemble SOP 8-12:Remove Speaker in the direction as below;
2 1
NO. Part Name Part No. Qty
1 Speaker S33-2100250-F33 1
PR201(MS-1223)Disassemble SOP 8-13:Remove 2pcs M2*3mm Screws, Remove 2pcs M2*3.5mm Screws Then Remove Touchpad Bracket as the
blew
Note:Screw driver torque is 1.5~1.8kgf.cm
1
3
2
4
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 2
2 Screw E43-1203501-H29 2
3 Touchpad_Bracket E2M-2210811-Y28 1
PR201(MS-1223)Disassemble SOP
8-14:Remove Touchpad FFC (To Button) 、Finger Printer board Cable, Then Remover Touchpad Button Board
in the direction as below;
8-15:Remove Finger Printer Board in the direction as below;
NO. Part Name Part No. Qty
1 Touchpad Button Board 607-12223-010 1
2 Finger Printer Board 607-13312-01S 1
PR201(MS-1223)Disassemble SOP
8-16:Remove Touchpad FFC (To Button) ,Then Remover Touchpad Module in the direction as below;
NO. Part Name Part No. Qty
1 Touchpad Module S78-3700270-SD2 1
2 Touchpad FFC (To Button) K1C-1012012-J36 1
3 Upper Case Assy 307-221C216-H74 1
PR201(MS-1223)Disassemble SOP
8-17:Remove Touchpad FFC (To M/B) in the direction as below;
NO. Part Name Part No. Qty
1 Touchpad Button Board 607-12223-010 1
2 Touchpad FFC (To M/B) K1C-1012016-J36 1
8-18:Remove Finger Printer board Cable in the direction as below;
NO. Part Name Part No. Qty
1 Finger Printer Board 607-13312-01S 1
2 Finger Printer board Cable K1C-1006016-J36 1
PR201(MS-1223)Disassemble SOP
8-19:Remove Bluetooth Antenna ,Then Remove BLUETOOTH CABLE in the direction as below;
8-20:Remove BLUETOOTH MODULE in the direction as below;
NO. Part Name Part No. Qty
1 BLUETOOTH ANTENNA S79-1800610-V03 1
2 BLUETOOTH MODULE 605-6837D-070 1
3 BLUETOOTH CABLE K10-3008063-H58 1
PR201(MS-1223)Disassemble SOP ■ 9. LOWER CASE ASSY
9-1:Remove1pcs M2.5*5mm Screw ,Then Remove BLUETOOTH ANTENNA in the direction as below;
Note:Screw driver torque is 1.8~2.2kgf.cm
1
9-2:Remove M/B;
NO. Part Name Part No. Qty
1 Screws E43-I250551-H29 1
2 Main Board 607-13311-01S 1
3 BLUETOOTH ANTENNA S79-1800610-V03 1
PR201(MS-1223)Disassemble SOP
9-3:Remove WLAN Antenna-L、WLAN Antenna-R ,Then Remove RJ11 CABLE in the direction as below;
RJ11 CABLE
WLAN Antenna-L WLAN Antenna- R
NO. Part Name Part No. Qty
1 WLAN Antenna-L S79-1800590-V03 1
2 WLAN Antenna-R S79-1800580-V03 1
3 RJ11 CABLE K10-3002094-H58 1
PR201(MS-1223)Disassemble SOP
9-4:Remove TV IO JACK;
NO. Part Name Part No. Qty
1 TVIO JACK K19-3001009-H39 1
2 Lower Case Assy 307-221D214-Y31 1
PR201(MS-1223)Disassemble SOP ■ 10、LCD MODULE ASSY 10-1:Remove 2pcs LCD Rubber 、2pcs LCD_Mylar ,Then Remove 2pcs LCD BEZEL RUBBER in the direction shown
below;
10-2:Remove 4pcs M2.5*4 mm screws in the direction shown below;
Note:Screw driver torque is 2.5-2.8kgf.cm
LCD Rubber
LCD_ Mylar
LCD Rubber LCD BEZEL RUBBER
LCD BEZEL RUBBER
43
1 2
LCD_ Mylar
NO. Part Name Part No. Qty
1 LCD Rubber E2Y-2210711-Y40 2
2 LCD MYLAR E2Y-2211111-G40 2
3 Screw E43-I250551-H29 4
4 LCD BEZEL RUBBER E2Y-2210711-Y40 2
PR201(MS-1223)Disassemble SOP
10-3:Remove LCD Bezel in the direction as below;
NO. Part Name Part No. Qty
1 LCD BEZEL 307-221B212-Y31 1
PR201(MS-1223)Disassemble SOP
10-4:Remove 2pcs M2.5*4mm screws in the direction as below;
Note:Screw driver torque is 2.0~2.3kgf.cm
2 1
NO. Part Name Part No. Qty
1 Screw E43-I250551-H29 2
PR201(MS-1223)Disassemble SOP
10-5:Remove Hinge_L _R in the direction as below;
10-6:Remove 2PcsHinge Cap-L-R in the direction as below;
1
1
NO. Part Name Part No. Qty
1 Hinge_Left E2M-2211311-G60 1
2 Hinge_Right E2M-2211411-G60 1
3 Hinge Cap-L-R E2P-2211411-D37 2
PR201(MS-1223)Disassemble SOP
10-7:Remove Inverter Cable in the direction as below;
10-8:Remove Inverter Module ,Then Remove DISPLAY MODULE in the direction as below;
NO. Part Name Part No. Qty
1 Notebook Inverter S78-3300460-S49 1
2 DISPLAY MODULE S78-2307190-A90 1
PR201(MS-1223)Disassemble SOP 10-9:Remove 3G ANTENNA in the direction as below;
NO. Part Name Part No. Qty
1 3G ANTENNA OS7-1223010 1
PR201(MS-1223)Disassemble SOP
10-10:Remove Camera Cable, and then Remove CMOS Camera Module in the direction as below;
NO. Part Name Part No. Qty
1 Display Module S78-2307190-A90 1
2 CMOS Camera Module S1F-0003020-C54 1
3 Camera Cable K10-3004096-H39 1
PR201(MS-1223)Disassemble SOP
10-11:Remove MICROPHONE in the direction as below;
NO. Part Name Part No. Qty
1 MICROPHONE S34-2100350-N44 1
2 LCD Cover Assy 307-221A211-H74 1
PR201(MS-1223)Disassemble SOP
10-12:Remove LCD LVDS Cable in the direction as below;
NO. Part Name Part No. Qty
1 LCD LVDS Cable K19-3001009-H39 1
PR201(MS-1223)Disassemble SOP 10-13:Remove4pcs M2*3mm Screws, Then Remove LCD Bracket in the direction as below;
Note:Screw driver torque is 1.6~1.8kgf.cm
2 1
1
2 2
1
NO. Part Name Part No. Qty
1 Screw E43-1203003-H29 4
2 LCD-Bracket-R E2M-2211211-Y28 1
3 LCD-Bracket-L E2M-2211111-Y28 1
PR201(MS-1223)screws specifications
Photo Screw specification label
(M2.5*L5) black
(M2*L3)white
(M2.5*L4) black
(M2*L3.5) black
(M2*6)white
PR201(MS-1223)screws specifications ■ 1、BOTTOM DOOR ASSY total 9Pcs screws,
specification:
Photo Screw Specification label
(M2.5*L5) black
PR201(MS-1223)screws specification ■ 2、THERMAL-KIT and WIRELESS CARD total 22Pcs screws , specification:
2 1
3
4
Photo Screw specification label
(M2.5*L5) black
(M2*L3)white
(M2*6)white
Note:CPU Thermal Module screws on the order of lock
PR201(MS-1223)screws specification ■ 4、LCD BEZEL total 4Pcs screws,
specification:
Photo Screw specification label
(M2.5*L4) black
PR201(MS-1223)screws specification ■ 5、LCD MODULE ASSY total 6Pcs screws,
specification:
Photo Screw specification label
(M2.5*L4) black
(M2*L3)white
PR201(MS-1223)screws specification ■ 7、Upper Case Assy and NB total 1pcs screw ,
specification:
Photo Screw specification label
(M2.5*L5) black
PR201(MS-1223)screws specification ■ 7、Upper Case ASSY total 10pcs screws ,
specification:
Photo Screw specification label
(M2*L3.5) black
(M2*L3)white
PR201(MS-1223)screws specification ■ 8、NB 1pcs screw ,
specification:
Photo Screw specification label
(M2.5*L5) black