1 Battery Pack 2 BOTTOM DOOR ASSY 3 WLAN HINGE COVER … › moderator › assembly-guides › ms-1223-di… · PR201（MS-1223）Disassemble SOP 1、Battery Pack 1-1：According

PR201 （MS-1223）Disassemble SOP

■ 1、Battery Pack

■ 2、BOTTOM DOOR ASSY

■ 3、THERMAL-KIT And CPU Module

■ 4、WLAN、MDC And RAM Module

■ 5、HDD Module ASSY

■ 6、ODD Module ASSY

■ 7、HINGE COVER ASSY

■ 8、UP CASE ASSY

■ 9、LOWER CASE ASSY

■ 10、LCD MODULE ASSY

PR201（MS-1223）Disassemble SOP

■ 1、Battery Pack 1-1：According to the direction of the arrow to Push the battery Unlock button shown below;

1-2：Push the battery Release button in the direction shown below, then slide the battery pack remove of the slot;

NO. Part Name Part No. Qty

1 Battery Pack S9N-0182210-W38 1


■ 2、BOTTOM DOOR ASSY

2-1：Use Screw Driver to remove 5pcs M2.5*5mm screws on the Bottom Door.

Note：Screw driver torque is 1.8~2.2kgf.cm

2-2：Remove Bottom Door in the direction as below;


1 Screw E43-1250551-H29 5

2 BOTTOM DOOR ASSY 307-221J212-W28 1


■ 3、THERMAL-KIT And CPU Module 3-1：Remove 3pcs M2*6MM screws, Then RemoveCPU Fan sink Cable and 4pcs M2.5*5 screws in the direction shown below;.

Note：CPU Thermal Module Screw driver torque is 2.0~2.5kgf.cm（1-4）

Note：CPU FAN Screw driver torque is 1.5~2.0kgf.cm（1-3）

3

2

4

1

3

1

2

Cable


1 screw E43-1206001-H29 3

2 screw E43-I250551-H29 4


3-2：Remove CPU Fan sink,Then Remove CPU Thermal Module in the direction as below;


1 CPU FAN E33-0900212-F05 1

2 CPU Thermal Module E31-0800311-F05 1


3-3：Let the CPU Slot open with Screw Driver;

3-4：Remove CPU Module in the direction as below;


1 CPU Module A09-2520106-I06 1


■ 4、WLAN、MDC And RAM Module

4-1：Remove 1pcs M2*3mm screw,Then Remove ANTENNA/HIGH-TEK/R-L in the direction shown below;


4-2：Remove WIRELESS CARD in the direction shown below;


1 WIRELESS CARD S57-0800180-I06 1

2 Screw E43-1203003-H29 1


4-3：Remove 2pcs M2*L3mm screws, Then Remove MDC Cable in the direction shown below;


1

2

4-4：Remove MODEM in the direction shown below;


1 MODEM S52-2801180-C59 1

2 Screw E43-1203003-H29 2

3 MDC Cable K10-3002094-H58 1


4-5：Push the RAM locks away;

4-6：Remove the RAM Module as below:


1 RAM Module S7C-S346703-T10 1

R201（MS-1223）Disassemble SOP

■ 5、HDD Module ASSY 5-1：Remove 2pcs M2.5*5mm screws and HDD Module in the direction shown below;


1

2


1 Screw E43-I250551-H29 2


5-2：Remove 2pcs M3*3.5mm Screws, Then Remove HDD Bracket in the direction shown below;


2

1


1 Screw E43-1303501-H29 2

2 HDD Bracket Assy E2M-2211511-Y28 1

3 HDD MODULE ASSY S71-2416504-T14 1


■ 6、ODD Module ASSY 6-1：Remove ODD Module in the direction shown below;


6-2：Remove ODD Bezel in the direction shown below;


1 ODD Bezel 307-221F212-Y31 1

PR201（MS-1223）Disassemble SOP 6-3：Remove 2pcs M2*3mm Screws,then remove ODD Bracket in the direction shown below;


1 2


1 Screw E43-1203003-H29 2

2 ODD Side Bracket E2M-2211611-Y28 1

3 ODD MODULE ASSY S7D-2270002-P87 1


■ 7、HINGE COVER ASSY 7-1：Attention: Battery slot Of 3pcs card;

2 1 3

7-2：Unlock the hooks of both sides;


7-3：Remove LCD LVDS Cable、CAMERA CABLE, Then Remove Inverter Cable in the direction shown below;

7-4：Remove MICROPHONE CABLE 、Speaker CABLE, Then Remove BLUETOOTH CABLE in the direction shown

below;


1 INVERTER Cable K1H-3006006-H39 1

2 Camera Cable K10-3004096-H58 1

3 LCD LVDS Cable K19-3020014-H58 1

4 BLUETOOTH CABLE K10-3008063-H58 1

PR201（MS-1223）Disassemble SOP 7-5：Pull out cable from the slot in the direction as below;


7-6：Remove 2pcs M2.5*5mm screws in the direction shown below;


2

1


1 Screw E43-I250551-H29 2


7-7：Remove LCD MODULE ASSY in the direction shown below;


■ 8、UPCASE ASSY

8-1：Remove 4pcs Middle Shielding Cover in the direction as below;

1 2 3 4


1 Middle Shielding Cover E2M-2211012-H48 4


8-2：Remove Keyboard in the direction as below;

8-3：Remove Keyboard Cable in the direction as below;


1 Keyboard S1N-1UUS231-C54 1


8-4：Remove 6pcs M2.5*5mm Screws in the direction as below;


2

3

4

5

1

6


1 Screws E43-I250551-H29 6


8-5：Remove SIM Card Door in the direction as below;


1 SIM CARD DOOR E2P-2210211-Y31 1


8-6：Remove 3pcs M2*3mm Screws in the direction as below;


3

2

1


1 Screw E43-1203003-H29 3


8-7：Remove PCI-EXPRESS DUMMY CARD, Then Remove SD DUMMY CARD in the direction as below;


1 PCI-EXPRESS DUMMY CARD E2P-2212814-H76 1

2 SD DUMMY CARD E2P-2212711-H76 1


8-8：Remove Touchpad FFC (To M/B) ，Then Remove Launch Board Cable in the direction as below;

8-9：Remove 2pcs M2*3.5mm Screws, Then Remove Launch Board in the direction as below;


2 1


8-10：Remove Launch Board Cable;


1 Screw E43-1203501-H29 2

2 Launch Board 607-1331A-01S 1

3 Launch Board Cable K1C-1020002-J36 1

PR201（MS-1223）Disassemble SOP 8-11：Remove 4pcs M2*3mm Screws, Then Remove SPEAKER_SHIELDING in the direction as below;

Note：Screw driver torque is 1.5~18kgf.cm

1 2 3 4


1 Screw E43-1203003-H29 4

2 SPEAKER_SHIELDING E2M-2210911-Y28 2

PR201（MS-1223）Disassemble SOP 8-12：Remove Speaker in the direction as below;

2 1


1 Speaker S33-2100250-F33 1

PR201（MS-1223）Disassemble SOP 8-13：Remove 2pcs M2*3mm Screws, Remove 2pcs M2*3.5mm Screws Then Remove Touchpad Bracket as the

blew


1

3

2

4


1 Screw E43-1203003-H29 2

2 Screw E43-1203501-H29 2

3 Touchpad_Bracket E2M-2210811-Y28 1


8-14：Remove Touchpad FFC (To Button) 、Finger Printer board Cable, Then Remover Touchpad Button Board

in the direction as below;

8-15：Remove Finger Printer Board in the direction as below;


1 Touchpad Button Board 607-12223-010 1

2 Finger Printer Board 607-13312-01S 1


8-16：Remove Touchpad FFC (To Button) ,Then Remover Touchpad Module in the direction as below;


1 Touchpad Module S78-3700270-SD2 1

2 Touchpad FFC (To Button) K1C-1012012-J36 1

3 Upper Case Assy 307-221C216-H74 1


8-17：Remove Touchpad FFC (To M/B) in the direction as below;


1 Touchpad Button Board 607-12223-010 1

2 Touchpad FFC (To M/B) K1C-1012016-J36 1

8-18：Remove Finger Printer board Cable in the direction as below;


1 Finger Printer Board 607-13312-01S 1

2 Finger Printer board Cable K1C-1006016-J36 1


8-19：Remove Bluetooth Antenna ,Then Remove BLUETOOTH CABLE in the direction as below;

8-20：Remove BLUETOOTH MODULE in the direction as below;


1 BLUETOOTH ANTENNA S79-1800610-V03 1

2 BLUETOOTH MODULE 605-6837D-070 1

3 BLUETOOTH CABLE K10-3008063-H58 1

PR201（MS-1223）Disassemble SOP ■ 9. LOWER CASE ASSY

9-1：Remove1pcs M2.5*5mm Screw ,Then Remove BLUETOOTH ANTENNA in the direction as below;


1

9-2：Remove M/B;


1 Screws E43-I250551-H29 1

2 Main Board 607-13311-01S 1

3 BLUETOOTH ANTENNA S79-1800610-V03 1


9-3：Remove WLAN Antenna-L、WLAN Antenna-R ,Then Remove RJ11 CABLE in the direction as below;

RJ11 CABLE

WLAN Antenna-L WLAN Antenna- R


1 WLAN Antenna-L S79-1800590-V03 1

2 WLAN Antenna-R S79-1800580-V03 1

3 RJ11 CABLE K10-3002094-H58 1


9-4：Remove TV IO JACK;


1 TVIO JACK K19-3001009-H39 1

2 Lower Case Assy 307-221D214-Y31 1

PR201（MS-1223）Disassemble SOP ■ 10、LCD MODULE ASSY 10-1：Remove 2pcs LCD Rubber 、2pcs LCD_Mylar ,Then Remove 2pcs LCD BEZEL RUBBER in the direction shown

below;

10-2：Remove 4pcs M2.5*4 mm screws in the direction shown below;

Note：Screw driver torque is 2.5-2.8kgf.cm

LCD Rubber

LCD_ Mylar

LCD Rubber LCD BEZEL RUBBER

LCD BEZEL RUBBER

43

1 2

LCD_ Mylar


1 LCD Rubber E2Y-2210711-Y40 2

2 LCD MYLAR E2Y-2211111-G40 2

3 Screw E43-I250551-H29 4

4 LCD BEZEL RUBBER E2Y-2210711-Y40 2


10-3：Remove LCD Bezel in the direction as below;


1 LCD BEZEL 307-221B212-Y31 1


10-4：Remove 2pcs M2.5*4mm screws in the direction as below;


2 1


1 Screw E43-I250551-H29 2


10-5：Remove Hinge_L _R in the direction as below;

10-6：Remove 2PcsHinge Cap-L-R in the direction as below;

1

1


1 Hinge_Left E2M-2211311-G60 1

2 Hinge_Right E2M-2211411-G60 1

3 Hinge Cap-L-R E2P-2211411-D37 2


10-7：Remove Inverter Cable in the direction as below;

10-8：Remove Inverter Module ,Then Remove DISPLAY MODULE in the direction as below;


1 Notebook Inverter S78-3300460-S49 1

2 DISPLAY MODULE S78-2307190-A90 1

PR201（MS-1223）Disassemble SOP 10-9：Remove 3G ANTENNA in the direction as below;


1 3G ANTENNA OS7-1223010 1


10-10：Remove Camera Cable, and then Remove CMOS Camera Module in the direction as below;


1 Display Module S78-2307190-A90 1

2 CMOS Camera Module S1F-0003020-C54 1

3 Camera Cable K10-3004096-H39 1


10-11：Remove MICROPHONE in the direction as below;


1 MICROPHONE S34-2100350-N44 1

2 LCD Cover Assy 307-221A211-H74 1


10-12：Remove LCD LVDS Cable in the direction as below;


1 LCD LVDS Cable K19-3001009-H39 1

PR201（MS-1223）Disassemble SOP 10-13：Remove4pcs M2*3mm Screws, Then Remove LCD Bracket in the direction as below;


2 1

1

2 2

1


1 Screw E43-1203003-H29 4

2 LCD-Bracket-R E2M-2211211-Y28 1

3 LCD-Bracket-L E2M-2211111-Y28 1

PR201（MS-1223）screws specifications

Photo Screw specification label

(M2.5*L5) black

(M2*L3)white

(M2.5*L4) black

(M2*L3.5) black

(M2*6)white

PR201（MS-1223）screws specifications ■ 1、BOTTOM DOOR ASSY total 9Pcs screws,

specification：

Photo Screw Specification label

(M2.5*L5) black

PR201（MS-1223）screws specification ■ 2、THERMAL-KIT and WIRELESS CARD total 22Pcs screws , specification：

2 1

3

4


(M2.5*L5) black

(M2*L3)white

(M2*6)white

Note：CPU Thermal Module screws on the order of lock

PR201（MS-1223）screws specification ■ 4、LCD BEZEL total 4Pcs screws,

specification：


(M2.5*L4) black

PR201（MS-1223）screws specification ■ 5、LCD MODULE ASSY total 6Pcs screws,

specification：


(M2.5*L4) black

(M2*L3)white

PR201（MS-1223）screws specification ■ 7、Upper Case Assy and NB total 1pcs screw ，

specification：


(M2.5*L5) black

PR201（MS-1223）screws specification ■ 7、Upper Case ASSY total 10pcs screws ，

specification：


(M2*L3.5) black

(M2*L3)white

PR201（MS-1223）screws specification ■ 8、NB 1pcs screw ，

specification：


(M2.5*L5) black

Documents

1 Battery Pack 2 BOTTOM DOOR ASSY 3 WLAN HINGE COVER … › moderator › assembly-guides › ms-1223-di… · PR201（MS-1223）Disassemble SOP 1、Battery Pack 1-1：According