!

!

Yingli&Green&Energy&Holdings&Co.,&Ltd.&

Solar&Module&List&

&&

YGE&72&Cell&–&Series&2:&

• 345W!–!YL345P*35b!

• 340W!–!YL340P*35b!!

• 335W!–!YL335P*35b!

• 330W!–!YL330P*35b!

• 325W!–!YL325P*35b!

• 320W!–!YL320P*35b!

&!

Power Your Life

Yingli Green Energy Holding Company Limited (“Yingli Solar”)

provides the following Limited Product Warranty and Limited

Power Warranty (collectively, the “Limited Warranty”) with

respect to its photovoltaic module products (“PV Modules”

or “Modules”), subject to the conditions, exclusions and

limitations set forth below.

1 L I M I T E D P R O D U C T WA R R A N T Y Yingli Solar warrants to the purchaser (the “Customer”) that PV Modules shall

be free from defects in materials and workmanship under normal application, use and service conditions during a period of ten (10) years, beginning on the earlier of: i) the date such Modules were purchased; or ii) one (1) year anniversary from the production date (the “Warranty Start Date*”). If a PV Module fails to conform to this Limited Product Warranty during this ten-year period, Yingli Solar will, at its reasonable option, either (a) repair or replace the defective PV Module or parts without any charges, or (b) refund to the Customer at the current comparable market price of such Module, at the Customer’s claim.

This Limited Product Warranty does not warrant a specific power output, which shall be exclusively covered under the Limited Power Warranty below.

2 L I M I T E D P O W E R WA R R A N T YA. Limited 25-Year linear Power Warranty:

Yingli Solar further warrants that if, within twenty-five (25) years after the

Warranty Start Date, the degradation of the power output in the first year shall

not exceed 2.50% of the minimum labeled power output, which was originally

stipulated on the label of PV Modules; the degradation in every subsequent

year shall not exceed 0.70% of the minimum labeled power output. If the

power output decline, which was beyond the anticipated natural decline (as

set forth in the scheduled Power Output identified in Section C ) was due to

defects in materials or workmanship under normal application, use and service

conditions, Yingli Solar will remedy such decline in power, at its reasonable

option, either (a) repair or replace the defective PV Module or parts without

any charges , (b) provide the Customer with additional PV Module(s) to make

up for such decline of power output so that the total power out, which was

amounted up by the original one(s) and additional one(s) can equal or exceed

the value in Power Output Schedule, provided, it is feasible for the Customer to

install such additional PV Module(s), or (c) refund the di!erence between the

actual power output of the PV Module and the value in Power Output Schedule,

based on the comparable current market price at the Customer’s claim.

B. For purposes of determining PV Module power output, measurements shall

be based on, or normalized to, standard test conditions of 1000W/m2 irradiance,

25°C cell temperature, and AM 1.5 light spectrum. Measurements shall be made

in accordance with IEC 60904, and shall account for measurement system

error in accordance with EN 50380. Moreover, using the similar calibration

module as the type used by Yingli Solar to calibrate the sun simulator possible, and

conducting the power output test in well-known third party lab possible as well.

In the meanwhile, recording the Electroluminescence cell debris detection image

before the transportation and testing of the sample. The selection of the sample

and third party lab shall be determined by both parties to avoid any possible

disputes afterwards.

C. Power Output Schedule

Period in Years from Warranty Start Date

Minimum Power Output at the end of each year

0 100.00%

I 97.50%

2 96.80%

3 96.10%

4 95.40%

5 94.70%

6 94.00%

7 93.30%

8 92.60%

9 91.90%

10 91.20%

11 90.50%

12 89.80%

13 89.10%

14 88.40%

15 87.70%

16 87.00%

17 86.30%

18 85.60%

19 84.90%

20 84.20%

21 83.50%

22 82.80%

23 82.10%

24 81.40%

25 80.70%

YINGLI SOLAR PV MODULE

Limited Warranty

Y I N G L I S O L A R .CO M

Revision Date May 1st, 2016

*Warranty start date: With regard to direct purchase without distribution, warranty start date shall

be the date agreed in a contract or the issuing date on the original invoice; In the event of resale

or long storage, there shall be a default grace period before the modules are installed. However,

the period shall not exceed one year after the recorded factory date on Yingli inventory records..

3 G E N E R A L C O N D I T I O N S , E X C L U S I O N S A N D L I M I TAT I O N S

A. In no event shall the warranty period of any implied warranties be beyond

the applicable warranty period identified in sections 1 or 2, above. Some

countries, states or jurisdictions may not recognize limitations on warranty

periods, so the above limitation may not apply to you. This warranty gives

you specific legal rights as a Customer, and it will not prevent you from

having additional rights based on laws, which may vary from jurisdiction

to jurisdiction. Neither seller of the PV Modules nor any other person is

authorized to make any warranties other than those set forth herein, or to

extend the warranty periods set forth above, on behalf of Yingli Solar.

B. Claims under the Limited Warranty must be filed within the applicable

warranty period for the Limited Warranty to be valid. The sales receipt from

the first Customer purchase, or other reasonable documentary proof, is

required in order to establish the Warranty Start Date.

C. The Limited Warranty is o!ered only to the original Customer and any person

to whom the title(s) of the Module(s) was transferred, provided that the PV

Modules remain installed at the site where they were originally installed,

(each, a “Claimant”).

D. The beneficiary of the Limited Warranty is the owner of the module(s), which

could be either the first-hand purchaser, which means the original customer,

or the final owner after transfers. It is to say that the Limited Warranty

concerns directly with the PV Module(s), which can be transferred and then

automatically gained without connection with the ownership of the power

station where the modules are installed or the transfer of the modules. The

Limited Warranty shall not revoke any indirect product liability and other

cooperating obligations during the sub purchasing process.

E. THE LIMITED WARRANTY SHALL NOT APPLY TO THE FOLLOWING

SCENARIOS:

The payment has not been fulfilled without acceptable reason according

to contract or after communication before the application of the Limited

Warranty services.

The Module(s) has been alternated, repaired or modified without the

expressed, prior written consent of Yingli Solar.

The Module(s) has been relocated at a new site, other than the original

installation site.

Non-compliance with the Yingli Solar’s Installation and User Manual.

Misuse, abuse, neglect, or accident in storage, transportation, handling,

installation, application, use or service.

Electrical surges, lightning, flood, fire, vandalism, tampering, accidental

breakage, module discoloration, or other events reasonably beyond Yingli

Solar’s control.

Installation on mobile platforms or in a marine environment; direct contact

with corrosive agents or salt water; pest damage; or malfunctioning

PV system components and other operating conditions, which are not

expressly allowed in the Installation and User Manual.

Alteration, removal or obliteration of the original PV Module label.

In addition, the Limited Warranty does not cover cosmetic blemishes

associated with installation, or the normal wear and tear of PV Modules.

Disputes on optical appearance di!erence of/between individual Module(s)

during acceptance inspection period is not accepted by Yingli Solar, and Yingli

Solar only provides reasonable exchange at cost of Customer in case that

resale of replaced module(s) with disputes is not a!ected by Customer.

F. The Limited Warranty does not cover PV Module installation and removal of

defective PV Modules, or re-installation of the repaired, replaced or additional

PV Modules, as well as the costs of any of the foregoing; and do not cover any

other costs, lost profits or lost revenues associated with the performance or

non-performance of defective PV Modules; provided, however, that for the

accepted warranty claims, Yingli Solar shall be responsible for reasonable

costs associated with transporting defective, repaired, replacement or

additional PV Modules from and back to Claimant.

G. Any additional PV Modules provided, and any PV Modules repaired or

replaced, by Yingli Solar under a warranty claim shall be covered by the same

Limited Warranties and terms as the original PV Modules purchased that

were the subject of the claim; no warranty periods or terms shall be extended

because of a warranty claim or remedy. Yingli Solar shall make commercially

reasonable e!orts to replace defective PV Modules with new or refurbished

PV modules of the same or similar size and appearance, but reserves the

right to deliver another PV Module type in the event that Yingli Solar has

discontinued production of the PV Module type that is the subject of the

warranty claim provided, that such other PV Module type is compatible to

the Customer’s PV System. Replaced PV Modules and parts shall become the

property of Yingli Solar.

H. For EU: Notwithstanding anything to the contrary in this Limited Warranty, in

the case that the PV Modules are subject to the Undertaking Agreement (as

defined below), any replacement of the PV Modules due to warranty claims

shall be subjected to the arrangements as stipulated in the Undertaking

Agreement and/or other instructions enacted by European Commission.

Yingli Solar hereby reserves its right to determine in accordance with the

requirements of the Undertaking Agreement whether to replace the defected

PV Modules or to refund the Customer an amount equal to the original

price of defected PV Modules. The “Undertaking Agreement” refers to

(EU) Regulation No.423/2013 of 2 August 2013 “accepting an undertaking

o!ered in connection with the anti-dumping proceeding concerning imports

of crystalline silicon photovoltaic modules and key components (i.e. cells

and wafers) originating in or consigned from the People’s Republic of China”

which exempts importer from paying anti-dumping duty on condition that

net selling price will not be lower than a certain minimum import price

accompanied with other undertaking obligations.

4 O B TA I N I N G WA R R A N T Y S E R V I C E To obtain warranty service, the Customer or other Claimants should promptly

contact the seller from which they purchased the PV Modules, who will then

provide instructions and forms for filing the claim. If such seller no longer exists

or cannot be reached, the Customer or other Claimant may contact Yingli Solar

directly as indicated through our website, www.yinglisolar.com. Yingli Solar

will not accept the return of alleged defective PV Modules as well as payable

YINGLI SOLAR PV MODULE

Limited Warranty

Y I N G L I S O L A R .CO M

logistics expenses. Unless prior written authorization has been provided

by Yingli Solar generally (e.g. replacement agreement or email commitment

from Yingli Solar). Unless otherwise indicated, PV Modules that have been

authorized for return by Yingli Solar shall be shipped to a local Customer

Service Center as designated by Yingli Solar. Under the condition Yingli picks

up the replaced modules itself, the Customer shall properly pack and store the

modules to be replaced. In the event that a claim is rejected by Yingli Solar,

the Claimant is entitled to challenge the results by appealing to an accredited

testing laboratory. If there is any special agreement between Yingli Solar and

the Customer, the Customer shall explicitly inform Yingli Solar and submit such

agreement or evidence before applying the Limited Warranty Service.

5 E X C L U S I V E R E M E D I E S ; L I M I TAT I O N O F L I A B I L I T Y

The Limited Product and Limited Power Warranties set forth herein shall be the

sole and exclusive warranties granted by Yingli Solar, and shall be the sole and

exclusive remedies available to the Customer or other Claimant for any breach

of warranty, express or implied. Provision of remedies, in the manner and for the

periods described herein, shall constitute all the liabilities and responsibilities

of Yingli Solar to the Customer and each other Claimant with respect to the PV

Modules. In no event will Yingli Solar be liable for any consequential, incidental,

special or punitive damages arising from or out of the PV Modules or their

installation, use, performance or non-performance, or any defect or breach of

warranty, whether based on contract, warranty, negligence, strict liability, or

any other theory. Damages for loss of use, loss of profits, loss of revenues and

loss of production are specifically disclaimed. Some States or jurisdictions do

not allow the exclusion or limitation of incidental or consequential damages, so

the above limitation or exclusion may not apply to you. Under no circumstances

shall Yingli Solar’s liability for nonconforming PV Modules exceed the purchase

price paid by the customer for the particular PV modules involved, plus

reasonable transportation costs.

6 VA L I D I T Y This Limited Warranty applies to all PV Modules as well as YLxxxP (29b, 35b)

modules series dispatched from Yingli after 1st, May, 2016.

The Chinese Limited Warranty shall only apply to PV Modules sold inside

China region and shall not apply to any PV Modules resold outside China

region, unless otherwise agreed by Yingli .

This Limited Warranty applies only to certified products of Yingli, which are

duly labeled with “Yingli Solar” brand. It should not be considered as a warranty

to the power station, or any kind of commercial insurance. All the certified

products from Yingli Solar shall be labeled with the “Yingli Solar” logo, and its

Electroluminescence image is stored in Yingli, the sole flash test data of each

Module is provided to Customer as requested, which should be kept by the

Customers confidentially and properly for authenticity verification purpose.

7 M I S C E L L A N E O U S If any part or provision of this Yingli Solar PV Module Limited Warranty, or

the application thereof to any person or circumstance, is held invalid, void

or unenforceable, such holding shall not a!ect any other parts, provisions

or applications of this Yingli Solar PV Module Limited Warranty, which shall

remain in full force.

This Limited Warranty is available in multiple languages. If, for any reason,

there is a conflict between the English-language version and any other version,

the English-language version shall prevail.

YINGLI SOLAR PV MODULE

Limited Warranty

Y I N G L I S O L A R .CO M NYSE:YGE

© Yingli Green Energy Holding Co., Ltd.

Yingli Green Energy Holding Co., Ltd.

service@yingli.com

Service hotline : +86-312-2188055

Complaints hotline : +86-312-8922216

WD-LEGAL-YGE_LINEAR_EN_20160516_V03

Higher Durability

The multi-busbar design can decrease the risk of the cell micro- cracks and

fingers broken.

High Power Density

High conversion e!ciency and more power output per square meter, by

lower series resistance and improved light harvesting.

PID Resistant

Tested in accordance to the standard IEC 62804, our PV modules have

demonstrated resistance against PID (Potential Induced Degradation),

which translates to security for your investment.

Advanced Glass

Our high-transmission glass features a unique anti-reflective coating that

directs more light on the solar cells, resulting in a higher energy yield.

Independently tested for proven product quality and long-term

reliability. Millions of PV systems installed worldwide demonstrate

Yingli’s industry leadership.

IMPROVED POWER NEVER SETTLE FOR LESS

19.6%CELL EFFICIENCY

10 YEARPRODUCT WARRANTY

0 - 5 WPOWER TOLERANCE

25 Years Linear Warranty

YGE72 CELL SERIES 2

YINGLISOLAR.COM

Power Your Life

Yingli Green EnergyYingli Green Energy Holding Company Limited (NYSE: YGE), known as “Yingli Solar,” is one of the world’s leading solar panel manufacturers with the mission to provide affordable green energy for all. Yingli Solar makes solar power possible for communities everywhere by using our global manufacturing and logistics expertise to address unique local challenges.

Yingli’s Linear Performance Warranty

25

Years

201510510%

97.5%

91.2%

80.7%

Industry Standard Warranty

G E N E R A L C H A R A C T E R I S T I C S

Dimensions (L / W / H) 1960mm / 992mm / 40mm

Weight 22kg

YGE 72 CELL SERIES 2

Warning：Read the Installation and User Manual

in its entirety before handling, installing, and

operating Yingli Solar modules.

Yingli Partners:

Yingli Green Energy Holding Co., Ltd.

service@yingli.com

Tel: +86-312-2188055

© Yingli Green Energy Holding Co., Ltd.

Y I N G L I S O L A R .CO M

STC: 1000W/m2 irradiance, 25°C cell temperature, AM1.5g spectrum according to EN 60904-3.Average relative e!ciency reduction of 3.3% at 200W/m2 according to EN 60904-1.

NOCT: open-circuit module operation temperature at 800W/m2 irradiance, 20°C ambient temperature, 1m/s wind speed.

O P E R AT I N G C O N D I T I O N S

Max. system voltage 1000VDC/1500VDC

Max. series fuse rating * 15A

Operating temperature range -40°C to 85°C

Max. static load, front (e.g., snow) 5400Pa

Max. static load, back (e.g., wind) 2400Pa

Max. hailstone impact (diameter / velocity) 25mm / 23m/s

*DO NOT connect Fuse in Combiner Box with two or more strings in parallel connection

PA C K A G I N G S P E C I F I C AT I O N S

Number of modules per pallet 26

Number of pallets per 40' container 24

Packaging box dimensions

(L / W / H)1995mm / 1145mm / 1170mm

Box weight 616kg

• Due to continuous innovation, research and product improvement, the specifications in this product information sheet are subject to

change without prior notice. The specifications may deviate slightly and are not guaranteed.

• The data do not refer to a single module and they are not part of the offer, they only serve for comparison to different module types.

T H E R M A L C H A R A C T E R I S T I C S

Nominal operating cell temperature NOCT °C 45 +/- 2

Temperature coe!cient of Pmaxγ %/°C -0.38

Temperature coe!cient of Vocβ

Voc%/°C -0.29

Temperature coe!cient of Isc

αIsc

%/°C 0.03

C O N S T R U C T I O N M AT E R I A L S

Front cover (material / thickness) low-iron tempered glass / 3.2mm

Cell (quantity / material / number of busbars) 72 / multicrystalline silicon / 12 or 5

Frame (material ) anodized aluminum alloy

Junction box (protection degree) ≥ IP67

Cable (length / cross-sectional area) 1100mm / 4mm2

DS_YGE72CELL SERIES 2 -35b_40mm_EU_EN_20190101_V04

Unit: mm

Q U A L I F I C AT I O N S & C E R T I F I C AT E S

IEC 61215, IEC 61730, CE, ISO 9001:2015, ISO 14001:2015, BS OHSAS

18001:2007, SA 8000:2015

Electrical parameters at Nominal Operating Cell Temperature (NOCT)

Power output Pmax

W 254.5 250.8 247.1 243.4 239.7 236.0

Voltage at Pmax V

mppV 35.5 35.1 34.7 34.4 34.0 33.6

Current at PmaxI

mppA 7.18 7.14 7.11 7.08 7.06 7.02

Open-circuit voltage Voc

V 42.9 42.7 42.5 42.4 42.2 42.1

Short-circuit current Isc

A 7.64 7.60 7.57 7.54 7.51 7.47

E L E C T R I C A L P E R F O R M A N C E

Electrical parameters at Standard Test Conditions (STC)

Module typeYLXXXP-35b (XXX=Pmax)

YLXXXP-35b 1500V (XXX=Pmax)

Power output Pmax

W 345 340 335 330 325 320

Power output tolerances Pmax

W 0/+5

Module e!ciency ηm

% 17.7 17.5 17.2 17.0 16.7 16.5

Voltage at Pmax Vmpp

V 38.5 38.1 37.7 37.3 36.9 36.5

Current at Pmax Impp

A 8.97 8.93 8.89 8.85 8.82 8.78

Open-circuit voltage Voc

V 46.1 45.9 45.7 45.6 45.4 45.2

Short-circuit current Isc

A 9.45 9.41 9.37 9.33 9.29 9.25

CE R T I F I C A T E OF CO M P L I A N C ECertificate Number 20180404-E357540Report Reference E357540-20120830

Issue Date 2018-April-04

Bruce Mahrenholz, Director North American Certification Program

UL LLC

Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, pleasecontact a local UL Customer Service Representative at http://ul.com/aboutul/locations/

Page 1 of 2

Issued to: YINGLI ENERGY (CHINA) CO LTD3399 N CHAOYANG RD, BAODINGHEBEI 071051 CHINA

This is to certify thatrepresentative samples of

PHOTOVOLTAIC MODULES AND PANELS WITHSYSTEM VOLTAGE RATINGS OVER 600 VOLTSSEE ADDENDUM PAGE

Have been investigated by UL in accordance with theStandard(s) indicated on this Certificate.

Standard(s) for Safety: UL 1703-Flat-Plate Photovoltaic Modules and PanelsULC/ORD-C1703-01-Flat-Plate Photovoltaic Modules andPanels

Additional Information: See the UL Online Certifications Directory atwww.ul.com/database for additional information

---

Only those products bearing the UL Certification Mark should be considered as being covered by UL'sCertification and Follow-Up Service.

Look for the UL Certification Mark on the product.

CE R T I F I C A T E OF CO M P L I A N C ECertificate Number 20180404-E357540Report Reference E357540-20120830

Issue Date 2018-April-04

Bruce Mahrenholz, Director North American Certification Program

UL LLC

Any information and documentation involving UL Mark services are provided on behalf of UL LLC (UL) or any authorized licensee of UL. For questions, pleasecontact a local UL Customer Service Representative at http://ul.com/aboutul/locations/

Page 2 of 2

This is to certify that representative samples of the product as specified on this certificate were testedaccording to the current UL requirements.

USL/CNL – Models YL260P-35b, YL265P-35b, YL270P-35b, YL275P-35b, YL280P-35b, YL285P-35b,YL290P-35b, YL295P-35b, YL300P-35b, YL305P-35b, YL310P-35b, YL315P-35b, YL320P-35b(*),YL325P-35b(*), YL330P-35b(*), YL335P-35b(*),YL340P-35b(*),YL345P-35b(*),YL350P-35b(*);

YL215P-29b, YL220P-29b, YL225P-29b, YL230P-29b, YL235P-29b, YL240P-29b, YL245P-29b,YL250P-29b, YL255P-29b, YL260P-29b, YL265P-29b, YL270P-29b(*), YL275P-29b(*), YL280P-29b(*),YL285P-29b(*),YL290P-29b(*),YL295P-29b(*),YL300P-29b(*);

YL170P-23b, YL175P-23b, YL180P-23b, YL185P-23b, YL190P-23b, YL195P-23b, YL200P-23b,YL205P-23b, YL210P-23b;

(*) – Applicable for constant combination A only with cell type “YL156-PP-4 Ver.4”, “YL156-PP-5 Ver.2”,“G156M4”, “G156M5”; constant combination B; constant combination C.