X-SLIDE

X-SSLIDE sealsstandard dimensions catalogue

X-SSLIDE sealsstandard dimensions catalogue

ta

c

2 ECONOMOS

able of content

ontenContent

Introduction

X-SLIDE rod seals

X-SLIDE piston seals

F-SLIDE rod seals

F-SLIDE piston seals

Rod- and piston seals

Annex

5 General description6 Comparison X-ECOPUR® vs. PTFE materials8 Material combinations for X-SLIDE seals9 Special non-polyurethane X-SLIDE material combinations10 Recommended rod sealing systems (new design)11 Recommended rod sealing systems (substitution) 12 Description, technical data, housing recommendations X-SLIDE S09-E14 Standard size range X-SLIDE S09-E (standard)20 Description, technical data, housing recommendations X-SLIDE S09-ES22 Standard size range X-SLIDE S09-ES (heavy duty)24 Description, technical data, housing recommendations X-SLIDE K08-D26 Standard size range X-SLIDE K08-D (standard)30 Description, technical data, housing recommendations X-SLIDE K08-DS32 Standard size range X-SLIDE K08-DS (heavy duty)

34 General description35 Material combinations for F-SLIDE seals36 Description, technical data, housing recommendations F-SLIDE S09-E38 Standard size range F-SLIDE S09-E (standard)44 Description, technical data, housing recommendations F-SLIDE S09-ES46 Standard size range F-SLIDE S09-ES (heavy duty)48 Description, technical data, housing recommendations F-SLIDE K08-D50 Standard size range F-SLIDE K08-D (standard)54 Description, technical data, housing recommendations F-SLIDE K08-DS56 Standard size range F-SLIDE K08-DS (heavy duty)

58 Additional (less common) standard profiles59 Special tailormade or customized solutions60 Technical Fax enquiry sheet for rod seals61 Technical Fax enquiry sheet for piston seals

62 Overview of total ECONOMOS® seal range63 Trade marks, liability exclusion63 Other ECONOMOS® products and services

X-SLIDE SEAL RANGE

F-SLIDE SEAL RANGE

TAILORMADE X-SLIDE SOLUTIONS

ECONOMOS® ABILITIES

3 ECONOMOS®

S09-E basic information

4 ECONOMOS•

5 ECONOMOS®

ECONOMOS® “X-SLIDE seal range” is the new family of elastomerically energizedsealing elements in the special newly developed hard grade polyurethane materialsX-ECOPUR®-57D, XH-ECOPUR®-60D and XS-ECOPUR®-57D. Comparable elastomericenergized PTFE sealing elements (with many trade names and brands but mainlyknown as sliding seals, step seals or composite seals) have been standard sealingelements in hydraulic cylinders for many years. These PTFE sealing systems fulfil thedemands of low friction and stick-slip free operation very well, but often they cannotstand up against increasing technological requirements, especially with regard towear resistance, leakage behaviour and ease of installation and assembly.

The newly developed X-SSLIDE seal range meets all the necessary requirements:

• Low friction and no stick-slip behaviour• Outstanding leakage performance• Superior extrusion and wear characteristics• Excellent installation and assembly properties

Due to these criteria, seals based on these special polyurethanes are an ideal repla-cement for conventional PTFE based composite seals, provided that the temperaturerange or pressure fluid are within the recommended operating envelope (see techni-cal data on pages 12, 20, 24, 30). In the event that high temperatures or uncommonfluids are used, please see Economos® F-SLIDE seal range on pages 34 - 57.

The improved wear resistance achieved by the use of X-SLIDE seals made from X-ECOPUR® materials will not only lead to extended lifetimes compared to PTFEsystems, but also have lower demands of surface roughness. Furthermore, the betterextrusion resistance allows larger component tolerances (extrusion gaps) than com-parable PTFE seals, which gives our customers the advantage of more economicalproduction of their components.

Owing to the innovative ECONOMOS® manufacturing system, X-SLIDE sealing ele-ments are available in single units as well as short runs on a just-in-time basis.Furthermore, due to the thermoplastic structure of the material, any seal profile canalso be produced in high quantities by injection moulding (unlike PTFE), thereby pro-viding significant cost savings.

Seals and sealing elements manufactured from X-ECOPUR® materials are suitable forhigher pressures or larger extrusion gaps than PTFE seals and have an outstandingwear resistance leading to longer lifetimes. These benefits along with the installati-on, assembly, low speed operation and sealability advantages ensure that fluid powersealing has truly entered the 21st century.

General descriptionX-SLIDE seal range

Summary

Introduction

6 ECONOMOS®

Extensive test rig investigations and finite element analysis have shown thatseals based on these special polyurethanes are an ideal replacement ofPTFE composite seals for most common fluid power systems.

The following shows a summary of our comparative tests:

Pressure resistance / wear characteristics: ECONOMOS® X-ECOPUR® variations showsuperior extrusion and wear characteri-stics. They are capable of higher pressureranges and respectively larger extrusiongaps than comparable PTFE systems andhave, due to their superior wear characte-ristics, a higher lifetime.

Leakage behaviour:The requirement of low rod sealing leaka-ge with PTFE seals is normally only obtai-ned by fitting seals in costly multipart solu-tions (tandem arrangement) or in combina-tion with a secondary lip seal. The superi-or low leakage-values of ECONOMOS® X-ECOPUR® materials make these seal profi-les - even without multipart solutions -ideal for all hydraulic applications.

Friction / Stick-slip effect

Based on the excellent tribological pro-perties of the new X-ECOPUR® grades, thefriction force of X-SLIDE seals are on thelevel of high-grade PTFE seals and lessthan 50% of standard polyurethane lipseals. Extensive tests showed also that theStick-Slip performance of the X-SLIDEseries is absolutely comparable to stan-dard PTFE sealing systems. Wherever friction is an issue - X-SLIDE isthe right choice.

Material compaComparison X-EECOPUR® vs. PTFE materials

X-ECO+ • Installation properties ++++++++++ • Friction / Stick-slip effect ++++++ • Leakage behaviour ++++++++ • Wear characteristics ++++++++ • Pressure resistance +++++

PTFE TEST PARAMETERS X-ECOPUR®

Extrusion length of composite seal materials

Leakage of various composite seal materials

X-ECOPUR® - XH-ECOPUR® - PTFE 40 Bz. PTFE Glass frict. mod.57D 60D MoS2 virgin PTFE

X-ECOPUR® - XH-ECOPUR® - PTFE 40 Bz. PTFE Glass frict. mod.57D 60D MoS2 virgin PTFE

Relative friction force of standard rod seals (rod Ø50mm)

c

Lip seal X-Slide Seal F-Slide Seal(Polyurethane) (X-ECOPUR®-57D) (PTFE 40% Bz.)

7 ECONOMOS®

A mayjor factor in the consideration of PTFE sealing systems is the problemassociated with installation and assembly. These factors are due to theinert nature of PTFE materials. The elastomeric ECONOMOS® X-SLIDEseals overcome these problem.

The following shows a summary of our comparative tests:

Installation properties / assembly:Compared to PTFE solutions, ECONOMOS® X-ECOPUR® composite seals show the samematerial hardness but considerably lowerresidual deformation and need lower moun-ting forces. An additional benefit is the resi-stance to damage on assembly and installati-on, which can be a major problem with PTFEcompounds. Also, there is no requirement forsizing or calibrating the seals after assembly.

The well known principle of the PTFE - geometry with its stepdesign of the dynamic sealing surface is also used for thenew range of X-SLIDE seals, small modifications of the X-ECOPUR® design amplify the improvements which are crea-ted by the excellent properties of the material. The pictures(see right) of a FE analysis show the difference. Owing to thehigher flexibility of the material compared with PTFE compo-unds, the new X-SLIDE seals show a very regularstress/strain allocation under a load of up to several hun-dred bar. The dynamic sealing edge especially is not as hig-hly loaded as at the PTFE design which leads to minimum ofwear and a long operation life at simultaneously excellentsealing performance. Also the extrusion endangered heelarea of the seal shows a strong stress reduction which leadsto an excellent extrusion resistance and an optimised backpumping ability.

risonOPUR® vs. PTFE+ • Installation properties ++++++++++ • Friction / Stick-slip effect ++++++ • Leakage behaviour ++++++++ • Wear characteristics ++++++++ • Pressure resistance +++++

PTFE TEST PARAMETERS X-ECOPUR®

Residual deformation of sealing materials

frict. mod. PTFE PTFE XH-ECOPUR®- X-ECOPUR®-virgin PTFE Glass/ MoS2 Bronze 60D 57D

compa

Comparison of X-ECOPUR®

and PTFE materials with FEA Analysis

• Expanding sleeve • Loading mandrel • Calibration sleeve

Due to the excellent deformation beha-viour of the ECONOMOS® X-ECOPUR®

materials, the complex and costly instal-lation tools such as expanding and cali-bration sleeves and loading mandrelsare no longer needed. You can simplysnap-in or stretch over the seals into thehousing without any tools (see right).Installation procedure of PTFE seals Installation procedure of

X-ECOPUR® seals

Comparison X-EECOPUR® vs. PTFE materials

PTFE seal

X-ECOPUR® seal

material comb

matStandard material combinations for X-SSLIDE seals

8 ECONOMOS®

X-EECOPUR®-557D / NBR70*green black

XH-EECOPUR®-660D / NBR70*red black

XS-EECOPUR®-557D / NBR70*grey black

XG-EECOPUR®-554D / NBR70*red black

-30°C to +100°C

-20°C to +100°C

-20°C to +100°C

-20°C to +100°C

Standard hard grade polyurethane material for mineral oilbased hydraulic fluids.Outstanding leakage behaviour, superior extrusion and wearcharacteristics, very good installation and assembly properties.

Hydrolysis resistant hard grade polyurethane material for waterbased, flame retardant hydraulic fluids (HFA, HFB) and biologi-cally degradable fluids (bio-oils).Excellent leakage behaviour, superior extrusion and wear cha-racteristics, very good installation and assembly properties.

Hard grade polyurethane material with additional solid lubri-cants for under lubricated systems (e.g. pneumatics).Very good leakage behaviour, best extrusion and wear charac-teristics, excellent installation and assembly properties.

Cast hard grade polyurethane material for large diameter seals(above 600 mm), for water based, flame retardant hydraulicfluids (HFA, HFB) and biologically degradable fluids (bio-oils).Excellent leakage behaviour, superior extrusion and wear cha-racteristics, very good installation and assembly properties.

Standard material combinations

* ECORUBBER 1 (NBR 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS

Due to the ECONOMOS® world renowned materials expertise, it is possible to supply many special customised polyuretha-ne and other materials in different colours and hardnesses, for instance; FDA compliant food grade H-EECOPUR® (in red,

blue and natural colour). Please consult our technical department for further information.

9 ECONOMOS®

binations

terialsSpecial non-ppolyurethane material combinations for X-SSLIDE seals

ECOWEAR 1000 / NBR70*white / light grey black

ECOWEAR 1000 / MVQ70**white / light grey reddish brown

-30°C to +80°C

-55°C to +80°C

Ultra high molecular weight polyethylene material (UHMWPE)for use in mineral oils, water hydraulics and pneumatics.Good leakage behaviour, good extrusion and wear characteri-stics, limited temperature resistance compared to X-ECOPUR®

materials. Generally harder to install.

Ultra high molecular weight polyethylene material (UHMWPE)in combination with silicone '0'ring for food and pharmaceuti-cal applications.Increased low temperature resistance compared to X-ECOPUR® materials. Generally harder to install.

In addition to polyurethane combinations, ECONOMOS® can offer special non polyuret-hane (ECOWEAR 1000) material to provide the best possible solution for special applica-tions. Mainly used in water applications, food and pharmaceutical industries and in spe-cial pneumatic applications.

Special non-polyurethane material combinations

* ECORUBBER 1 (NBR 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS** ECOSIL (MVQ 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS

recommended

syRecommended rod sealing systems (new design)

10 ECONOMOS®

X-SLIDE S09-EE seal complemented by a double wiper A11-AA, with guide ring F01.Recommended rod sealing system for standard hydraulic applications in the medium pressu-re range. The most economic solution with excellent performance.

XX-SSLLIIDDEE SS0099-EE sseeaall - special polyurethanesin a hardness of 54 to 60 Shore D WWiippeerr AA1111-AA - polyurethane in a hardness of95 Shore A/ 48 Shore D GGuuiiddee rriinngg FF0011 - PTFE-compounds, polyace-tal, polyamide or fabric reinforced polyester

XX-SSLLIIDDEE SS0099-EE pprriimmaarryy sseeaall - special polyuretha-nes in a hardness of 54 to 60 Shore D LLiipp-sseeaall SS0011-PP - polyurethane in a hardness of 95Shore A/ 48 Shore D WWiippeerr AA0011-AA - polyurethane in a hardness of 95Shore A/ 48 Shore D GGuuiiddee rriinngg FF0011 - PTFE-compounds, polyacetal,polyamide or fabric reinforced polyester

XX-SSLLIIDDEE SS0099-EE sseeaallss - special polyurethanesin a hardness of 54 to 60 Shore D WWiippeerr AA1111-AA - polyurethane in a hardness of95 Shore A/ 48 Shore D GGuuiiddee rriinngg FF0011 - PTFE-compounds, polyace-tal, polyamide or fabric reinforced polyester

Recommended sealing system 1 (speed up to 5 m/s)

X-SLIDE S09-EE primary seal followed by a secondary lip-seal S01-PP and wiper A01-AA, withguide ring F01. Recommended rod sealing system for medium and higher pressure ranges,especially in the event of extremely short, or unusually long strokes. Lip-seal S01-P providesfor additional sealing benefits.

Recommended sealing system 2 (speed up to 1,5 m/s)

“Tandem” arrangement of 2 X-SLIDE S09-EE seals followed by a double wiper A11-AA withguide ring F01. Recommended rod sealing system for higher gliding speeds. Secondary S09-E for additional sealing benefits. Identical design of both seals, easy to install in smaller dia-meter range.

Recommended sealing system 3 (speed up to 5 m/s)

6 - 29,930 - 49,950 - 99,9100 - 800above 800

Ød + 3Ød + 3Ød + 5Ød + 5Ød + 8

4,05,69,71525

Ød ØD1G LG

Guide ring F01 sizes

6 - 100100,1-149,9above 149,9

Ød + 8Ød + 12Ød + 15

Ød + 6Ød + 9

Ød + 11

4,05,56,5

1,01,52,0

Ød ØDw ØD1w Lw L1w

Wiper A01-AA sizes

6 - 49,950 - 99,9

above 99,9

Ød + 8Ød + 10Ød + 15

Ød + 4Ød + 5Ød+7,5

5,06,08,5

Ød ØDw ØD1w Lw

Wiper A11-AA sizes

6 - 29,930 - 49,950 - 99,9100 - 800above 800

Ød + 3Ød + 3Ød + 5Ød + 5Ød + 8

4,05,69,71525

Ød ØD1G LG

Guide ring F01 sizes

6 - 49,950 - 99,9

above 99,9

Ød + 8Ød + 10Ød + 15

Ød + 4Ød + 5Ød+7,5

5,06,08,5

Ød ØDw ØD1w Lw

Wiper A11-AA sizes

5 - 24,925 - 49,9

50 - 149,9150 - 299,9300 - 499,9500 - 699,9above 699,9

Ød+8Ød+10Ød+15Ød+20Ød+25Ød+30Ød+40

6,38

1014172532

Ød ØDs Ls

Seal S01-PP sizes

A11-AADDoouubbllee wwiippeerr(see left table)

S09-EEXX-SSLLIIDDEE sseeaall

(table page 13)

F01GGuuiiddee rriinngg

(see right table)

A01-AAWWiippeerr

(see left table)

S01-PPLLiipp-sseeaall

(see right table)


(top right table)


(table page 13)

A11-AADDoouubbllee wwiippeerr(see left table)


(table page 13)


(see right table)


(table page 13)

Ls

11 ECONOMOS®

substituted

ystemSubstitution (upgrade of existing systems)

A12-BB, A26-FF and A27-FF are possible substitutions for existing housings. A12-B recommended for contaminated environments.A26-F and A27-F are recommended to replace common PTFE wiper profiles.

Possible substitutions

A02-AA, A03-AA and A11-AA are possible substitutions for existing housings. A02-A mainly in larger diameter ranges.A03-A for existing open housings (self retaining).A11-A double acting wiper for systems with leakage vent between the seals.

Due to the excellent back-pumping ability the X-SLIDES09-E seal is a suitablereplacement for so called“buffer” seals such as S02-S.

Possible substitutions

A12-BB

A27-FF

A26-FF

A02-AA

A11-AA

S02-SSA03-AA

XX-SSLLIIDDEE SS0099-EE - special polyurethanes in a hardness of54 to 60 Shore D WWiippeerrss AA1111-AA // AA1122-BB - polyurethane in a hardness of 95Shore A/ 48 Shore D WWiippeerrss AA2266-FF // AA2277-FF - special polyurethane in ahardness of 54 to 60 Shore D (or PTFE compound) withNBR/FKM “O”-ring energisers.GGuuiiddee rriinngg FF0011 - PTFE compounds, polyacetal, polyami-de or fabric reinforced polyester

XX-SSLLIIDDEE SS0099-EE - special polyurethanes in a hardness of54 to 60 Shore D LLiipp-sseeaall SS0011-PP - polyurethane in a hardness of 95 Shore A/48 Shore D WWiippeerrss AA0011-AA // AA0022-AA // AA1111-AA - polyurethane in ahardness of 95 Shore A/ 48 Shore D WWiippeerr AA0033-AA - polyurethane in a hardness of 95 Shore A/48 Shore D with self retaining casing in polyacetal,polyamide or aluminum / steel (above 80 °C)GGuuiiddee rriinngg FF0011 - PTFE-compounds, polyacetal, polyami-de or fabric reinforced polyester

S09-E standard

X-S

12 ECONOMOS®

X-SSLIDE seals S09-EE description / technical data

Technical data

Advantages

General description

Pressure: up to 600 (800) bar / 60 (80) MPaSpeed: up to 5 m/sTemperature*: -30 °C to +100 °CMedia*: mineral based hydraulic oil fluids

flame retardant hydraulic fluids (HFA, HFB)biologically degradable oils (Bio-oils)water

Extrusion gap: depending on operation pressure and diameter(see table on page 13)

* see material combinations for X-SLIDE seals on pages 8 and 9

The specified data represent maximum values and should not be usedsimultaneously. If in doubt, please contact our technical department.Please also note our liability exclusion (page 63).

Detail X-SLIDE seal S09-E

- eexcellent static and dynamic sealing effect- hhigh wear resistance (high operational reliability)- ooutstanding extrusion resistance (allowing higher pressure / larger

gap sizes)- vvery good back-ppumping ability (optimised sealing effect, no interme-

diate drag pressure)- ccompact design (for small installation height)- llow friction, superior stick-sslip behaviour, high efficiency- eeasy installation procedure (due to higher flexibility of X-ECOPUR®

materials)- qquick delivery within days (or even hours), not weeks

(depending on diameter and quantity)- aavailable as individual single piece or medium lot production- aavailable in large quantities (injection moulded)- aavailable for all diameters up to 3000 mm

High performance rod sealing systems are essential in almost all equipments. The constantly increasing technological and envi-ronmental requirements - especially with regard to sealing effect, wear resistance and installation properties - led ECONOMOS® todevelop the special X-SLIDE seal range. These newly developed materials together with the optimised geometric design meet allthe above requirements. The hydrodynamic properties in combination with the excellent back-pumping ability of the residual oil filmare responsible for the long lifetime and reliable performance of these seals.X-SLIDE S09-E seal is the standard single acting rod seal, consisting of a X-ECOPUR® sealing element and an elastomeric '0' ringenergizer element. Interference fit and '0' ring preload ensure a good initial sealing effect. Increasing system pressure energizesthe '0' ring additionally for higher contact force and proportionally better sealing.

d dimensions

SLIDEX-SSLIDE seals S09-EE basic information

13 ECONOMOS®

Housing recommendation

Table of recommended X-SSLIDE seal S09-EE standard dimensions

• The above table shows our standard recommendations. Other dimensions - usually known as “light” and “heavy” series - are included in the tables on the following pages.• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.* specified extrusion gap valid up to temp. 80 °C, between 80 and 100 °C the gap size has to be lowered by 25%

d + 4,9d + 7,3

d + 10,7d + 15,1d + 20,5d + 24,0d + 27,3d + 38,0

3 - 7,98 - 18,9

19 - 37,938 - 199,9

200 - 255,9256 - 649,9650 - 999,91000 - 3000

2,23,24,26,38,18,19,5

13,8

0,40,61,01,31,81,82,53,0

2,53,54,55,06,08,0

10,012,0

1,782,623,535,337,007,008,40

12,00

0,30,40,50,50,70,70,81,1

0,30,30,40,40,50,50,70,8

0,20,20,30,30,40,40,50,7

0,10,10,20,20,20,20,30,4

RodØ d

GrooveØ D

Height L

Radiusr

Lead-inc

O-ringCord dia.

max. radial extrusion gap “s” *100 bar 200 bar 400 bar 600 bar

Ordering example, size listed in "available standard dimensions"

X-SLIDE S09-E, standard application, actual rod diameter: Ød=22 mm, predetermined or chosen housing dimensions (from list "S09-E available standard dimensions”) --> ØD=32,7mm, L=4,2mmrequired material: XH-ECOPUR® / NBR70 --> article number: 2XR0390 (out of list "S09-E available standard dimensions”,article-no.-row 2 for material combination XH-PU/NBR70)

Ordering example, size NOT listed in “available standard dimensions”, eg.: inch dimension

X-SLIDE S09-E, standard application, rod diameter Ød=25,4 mm (1”)housing diameter ØD=Ød+10,7 = 36,1mm and housing height L= 4,2 mm (from table “recommended S09-E standard dimensionsfor diameter range Ød 19 - 37,9 mm), required material: XH-ECOPUR® / NBR70 --> article number: not available, housingdimension d x D x L followed by material combination should be used for designation:

X-SLIDE S09-E 2XR0390Seal type article no.

Required designation for placing an order:

Required designation for placing an order: X-SLIDE S09-E 25,4 x 36,1 x 4,2mm XH-PU / NBR70Seal type housing dimensions material combination

For technical advice related to other housing configurations or non standard applications, please use fax enquiry form for rodseals on page 60.

+0,2

Surface R tmax Ra roughness (µm) (µm)

Sliding surface (rod) < 2.5 < 0.1 - 0.5Bottom of groove < 6.3 < 1.6

Groove face < 15 < 3bearing area Tp 50% - 95%

Seal housing tolerancesØ d f8Ø D H10

X-S

14 ECONOMOS®

7,98,99,9

10,911,011,912,913,015,313,916,314,915,017,316,917,019,319,5

18,919,021,321,519,922,320,923,323,521,922,925,325,529,727,327,530,731,029,329,532,733,031,332,332,535,736,033,336,739,035,338,737,340,739,342,7

3,04,05,06,06,0*7,08,0

8,0*8,09,09,0

10,010,0*10,012,0

12,0*12,012,0*

14,014,0*14,014,0*15,015,016,016,016,0*17,018,018,018,0*19,020,0

20,0*20,020,0*22,0

22,0*22,022,0*24,025,0

25,0*25,025,0*26,026,0

28,0*28,028,030,030,032,032,0

2,22,22,22,22,22,22,22,23,22,23,22,22,23,22,22,23,23,2

2,22,23,23,22,23,22,23,23,22,22,23,23,24,23,23,24,24,23,23,24,24,23,23,23,24,24,23,24,24,23,24,23,24,23,24,2

1XR00101XR00201XR00301XR00401XR00501XR00601XR00701XR00801XR00901XR01001XR01101XR01201XR01301XR01401XR01501XR01601XR01701XR0180

1XR01901XR02001XR02101XR02201XR02301XR02401XR02501XR02601XR02701XR02801XR02901XR03001XR03101XR03201XR03301XR03401XR03501XR03601XR03701XR03801XR03901XR04001XR04101XR04201XR04301XR04401XR04501XR04601XR04701XR04801XR04901XR05001XR05101XR05201XR05301XR0540





------------------

------------------------------------

RodØ d

GrooveØ D

Height L

Article-Nr.X-PU/NBR70

Article-Nr.XH-PU/NBR70

Article-Nr.XS-PU/NBR70

Article-Nr.XG-PU/NBR70

X-SLIDE seals S09-E available standard dimensions / article numbers

NOTE: due to our innovative manufacturing process we are able to produce any other dimension in betweenthis standard diameter range. For further information please contact our application engineers.

* Dimensions according to DIN/ISO 7425 Part 2bold dimensions are common, preferred measurements

SLIDE

15 ECONOMOS®

43,042,345,743,346,747,044,347,748,753,150,751,055,152,757,153,755,756,060,158,763,160,761,065,162,767,169,165,770,166,767,071,171,576,572,169,770,775,173,774,078,178,5

75,780,177,784,180,785,185,590,582,788,185,790,1

32,0*35,035,036,036,036,0*37,037,038,038,040,0

40,0*40,042,042,043,045,0

45,0*45,048,048,050,0

50,0*50,052,052,054,055,055,056,0

56,0*56,056,0*56,057,059,060,060,063,0

63,0*63,063,0*

65,065,067,069,070,070,0

70,0*70,072,073,075,075,0

4,23,24,23,24,24,23,24,24,26,34,24,26,34,26,34,24,24,26,34,26,34,24,26,34,26,36,34,26,34,24,26,36,38,16,34,24,26,34,24,26,36,3

4,26,34,26,34,26,36,38,14,26,34,26,3

1XR05501XR05601XR05701XR05801XR05901XR06001XR06101XR06201XR06301XR06401XR06501XR06601XR06701XR06801XR06901XR07001XR07101XR07201XR07301XR07401XR07501XR07601XR07701XR07801XR07901XR08001XR08101XR08201XR08301XR08401XR08501XR08601XR08701XR08801XR08901XR09001XR09101XR09201XR09301XR09401XR09501XR0960

1XR09701XR09801XR09901XR10001XR10101XR10201XR10301XR10401XR10501XR10601XR10701XR1080





------------------------------------------

------------

RodØ d

GrooveØ D

Height L








X-S

16 ECONOMOS®

93,190,795,195,5

100,597,693,795,7

100,1105,5104,1100,7105,1105,5110,5102,7107,1105,7

110,1110,7115,1115,5120,5120,1125,5120,7125,1125,5130,5130,1135,1140,5140,1140,5145,5142,1145,1150,5147,1145,7150,1152,1153,1150,7155,1155,5160,5155,6160,1165,5165,1170,5168,1170,1

78,080,080,080,0*80,082,583,085,085,085,089,090,090,090,0*90,092,092,095,0

95,0100,0100,0100,0*100,0105,0105,0110,0110,0110,0*110,0115,0120,0120,0125,0125,0*125,0127,0130,0130,0132,0135,0135,0137,0138,0140,0140,0140,0*140,0140,5145,0145,0150,0150,0153,0155,0

6,34,26,36,38,16,34,24,26,38,16,34,26,36,38,14,26,34,2

6,34,26,36,38,16,38,14,26,36,38,16,36,38,16,36,38,16,36,38,16,34,26,36,36,34,26,36,38,16,36,38,16,38,16,36,3







------------------

-------------------------------------

RodØ d

GrooveØ D

Height L








SLIDE

17 ECONOMOS®

175,1175,5180,5181,0180,1185,1190,5188,1190,1195,1195,5200,5201,0200,1205,5205,1210,5210,1215,1220,5221,0225,5230,5231,5232,5235,5240,5241,0245,5245,1250,5255,5260,5265,5270,5271,0

284,0289,0290,5294,0299,0304,5304,0309,0314,0319,0320,5324,0334,0344,5344,0354,0364,0370,5

160,0160,0*160,0

160,0*165,0170,0170,0173,0175,0180,0180,0*180,0

180,0*185,0185,0190,0190,0195,0200,0200,0200,0*205,0210,0211,0212,0215,0220,0220,0*225,0230,0230,0235,0240,0245,0250,0250,0*

260,0265,0270,0270,0275,0

280,0*280,0285,0290,0295,0300,0300,0310,0

320,0*320,0330,0340,0350,0

6,36,38,18,16,36,38,16,36,36,36,38,18,16,38,16,38,16,36,38,18,18,18,18,18,18,18,18,18,16,38,18,18,18,18,18,1

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,1







------------------------------------

------------------

RodØ d

GrooveØ D

Height L








X-S

18 ECONOMOS®

374,0384,0384,5389,0394,0399,0404,0414,0424,0434,0444,0454,0459,0464,0474,0484,0494,0504,0

509,0514,0524,0534,0544,0549,0554,0564,0574,0584,0594,0604,0609,0614,0624,0634,0644,0654,0664,0677,3683,3687,3697,3707,3712,3717,3724,0727,3737,3747,3757,3762,3767,3777,3787,3792,3

350,0360,0

360,0*365,0370,0375,0380,0390,0400,0410,0420,0430,0435,0440,0450,0460,0470,0480,0

485,0490,0500,0510,0520,0525,0530,0540,0550,0560,0570,0580,0585,0590,0600,0610,0620,0630,0640,0650,0656,0660,0670,0680,0685,0690,0700,0700,0710,0720,0730,0735,0740,0750,0760,0765,0

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,1

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,19,59,59,59,59,59,59,58,19,59,59,59,59,59,59,59,59,5


1XR23501XR23601XR23701XR23801XR23901XR24001XR24101XR24201XR24301XR24401XR2450

-------------------------



-------------------------



-------------------------

------------------

----------

4XR24604XR24704XR24804XR24904XR25004XR25104XR25204XR25304XR25404XR25504XR25604XR25704XR25804XR25904XR26004XR26104XR26204XR26304XR26404XR26504XR26604XR26704XR26804XR26904XR27004XR2710

RodØ d

GrooveØ D

Height L








SLIDE

19 ECONOMOS®

797,3807,3817,3822,3827,3837,3847,3857,3867,3877,3887,3897,3907,3912,3917,3927,3937,3947,3

957,3967,3977,3982,3

1.038,01.073,01.067,31.078,01.077,31.088,01.138,01.147,31.158,01.227,31.238,01.357,31.368,01.477,31.527,31.538,01.638,02.038,02.638,03.038,0

770,0780,0790,0795,0800,0810,0820,0830,0840,0850,0860,0870,0880,0885,0890,0900,0910,0920,0

930,0940,0950,0955,0

1.000,01.035,01.040,01.040,01.050,01.050,01.100,01.120,01.120,01.200,01.200,01.330,01.330,01.450,01.500,01.500,01.600,02.000,02.600,03.000,0

9,59,59,59,59,59,59,59,59,59,59,59,59,59,59,59,59,59,5

9,59,59,59,5

13,813,89,5

13,89,5

13,813,89,5

13,89,5

13,89,5

13,89,59,5

13,813,813,813,813,8

------------------

------------------------

------------------

------------------------

------------------

------------------------


4XR29004XR29104XR29204XR29304XR29404XR29504XR29604XR29704XR29804XR29904XR30004XR30104XR30204XR30304XR30404XR30504XR30604XR30704XR30804XR30904XR31004XR31104XR3120

RodØ d

GrooveØ D

Height L








S09-ES standa

X-SX-SSLIDE seals S09-EES description / technical data

20 ECONOMOS®

Technical data

Advantages

General description




* see material combinations for X-SLIDE seals on pags 8 and 9

The specified data represent maximum values and should not be usedsimultaneously. If in doubt, please contact our technical department.Please also note our liability exclusion (page 63).

Detail X-SLIDE seal S09-ES

- eexcellent static and dynamic sealing effect- hhigh wear resistance (high operational reliability)- ooutstanding extrusion resistance (allowing higher pressure / larger

gap sizes)- vvery good back-ppumping ability (optimised sealing effect, no inter-

mediate drag pressure)- ccompact design (for small installation height)- ccompact, stable square energizer ring profile (less deformation on

pulsating load) - eeasy installation procedure (due to higher flexibility of X-ECOPUR®

materials)- qquick delivery within days (or even hours), not weeks

(depending on diameter and quantity)- aavailable as individual single piece or medium lot production- aavailable in large quantities (injection moulded)- aavailable for all diameters up to 1.500 mm

X-SLIDE S09-ES seal is a "heavy duty" single acting rod seal consisting of an X-ECOPUR® sealing element and an elastomeric squa-re profile ring energizer element. Interference fit and preload of energizing element ensures a good initial sealing effect. Designedwith a square section energizer ring for increased stability and less deformation of the energizer under pulsating load. The optimi-sed hydrodynamic properties in combination with the excellent back-pumping ability of the residual oil film are responsible for thelong lifetime and reliable performance of these seals.

ard dimensions

SLIDEX-SSLIDE seals S09-EES basic information

21 ECONOMOS®

d + 10d + 15d + 20d + 25d + 30d + 35d + 40

5 - 49,950 - 59,9

60 - 199,9200 - 299,9300 - 529,9530 - 679,9680 - 1500

5,07,5

10,012,515,017,520,0

0,20,30,40,40,81,21,2

4,05,06,08,5

10,011,513,0

0,20,20,20,30,30,30,4

0,30,30,40,50,60,70,8

0,40,40,50,60,70,80,9

0,50,50,70,80,91,01,1

RodØ d

GrooveØ D

Height L

Radiusr

Lead-inc



Table of recommended X-SSLIDE seal S09-EES standard dimensions

• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.* specified extrusion gap valid up to temp. 80 °C, between 80 and 100 °C the gap size has to be lowered by 25%


X-SLIDE S09-ES, standard application, actual rod diameter: Ød=125 mm, predetermined or choosen housing dimensions (out of list “S09-ES available standard dimensions”) --> ØD=145mm, L=10mmrequired material: X-ECOPUR® / NBR85 --> article number: 1XRH0300 (out of list "S09-ES available standard dimensions”,article-no.-row 1 for material combination X-PU/NBR85)


X-SLIDE S09-ES, standard application, rod diameter Ød=101,6 mm (4”)housing diameter ØD=Ød+20 = 121,6 mm and housing height L= 10,0 mm (from table “recommended S09-ES standard dimen-sions for diameter range Ød 60 - 199,9 mm), required material: X-ECOPUR® / NBR85 --> article number: not available, housingdimension d x D x L followed by material combination should be used for designation:

Required designation for placing an order: X-SLIDE S09-ES 101,6 x 121,6 x 10 mm X-PU / NBR85Seal type housing dimensions material combination

For technical advice related to other housing configurations or non standard applications, please use fax enquiry form for rod sealson page 60.

Required designation for placing an order: X-SLIDE S09-ES 1XRH0300Seal type article no.





+0,2

X-S

22 ECONOMOS®

X-SLIDE seals S09-ES available standard dimensions / article numbers

15202226303538424650525558

65,067,069,070,071,080,083,085,090,095,0

100,0105,0110,0115,0120,0130,0145,0

160,0170,0180,0175,0195,0200,0225,0245,0255,0265,0275,0295,0305,0315,0330,0340,0350,0355,0360,0370,0380,0390,0410,0420,0

5101216202528323640424548

50,052,054,055,056,060,063,065,070,075,080,085,090,095,0

100,0110,0125,0

140,0150,0160,0170,0175,0180,0200,0220,0230,0240,0250,0270,0280,0290,0300,0310,0320,0325,0330,0340,0350,0360,0380,0390,0

5555555555555

7,57,57,57,57,5101010101010101010101010

101010101010

12,512,512,512,512,512,512,512,515151515151515151515

1XRH00101XRH00201XRH00301XRH00401XRH00501XRH00601XRH00701XRH00801XRH00901XRH01001XRH01101XRH01201XRH01301XRH01401XRH01501XRH01601XRH01701XRH01801XRH01901XRH02001XRH02101XRH02201XRH02301XRH02401XRH02501XRH02601XRH02701XRH02801XRH02901XRH0300

1XRH03101XRH03201XRH03301XRH03401XRH03501XRH03601XRH03701XRH03801XRH03901XRH04001XRH04101XRH04201XRH04301XRH04401XRH04501XRH04601XRH04701XRH04801XRH04901XRH05001XRH05101XRH05201XRH05301XRH0540





------------------------------

------------------------

RodØ d

GrooveØ D

Height L






SLIDE

23 ECONOMOS®

430,0440,0450,0460,0470,0480,0490,0500,0510,0520,0530,0540,0

550,0565,0575,0585,0595,0605,0615,0625,0635,0655,0685,0695,0705,0720,0740,0760,0780,0795,0810,0840,0860,0890,0940,0990,0

1.010,01.040,01.190,01.240,01.370,01.540,0

400,0410,0420,0430,0440,0450,0460,0470,0480,0490,0500,0510,0

520,0530,0540,0550,0560,0570,0580,0590,0600,0620,0650,0660,0670,0680,0700,0720,0740,0755,0770,0800,0820,0850,0900,0950,0970,0

1.000,01.150,01.200,01.330,01.500,0

151515151515151515151515

1517,517,517,517,517,517,517,517,517,517,517,517,52020202020202020202020202020202020

1XRH05501XRH05601XRH05701XRH05801XRH05901XRH06001XRH06101XRH06201XRH06301XRH06401XRH06501XRH0660

1XRH06701XRH06801XRH06901XRH07001XRH0710

-------------------------



-------------------------



-------------------------

------------

-----

4XRH06304XRH06404XRH06504XRH06604XRH06704XRH06804XRH06904XRH07004XRH07104XRH07204XRH07304XRH07404XRH07504XRH07604XRH07704XRH07804XRH07904XRH08004XRH08104XRH08204XRH08304XRH08404XRH08504XRH08604XRH0870

RodØ d

GrooveØ D

Height L





X-SLIDE seals S09-ES available standard dimensions / article numbers


K08-D standar

24 ECONOMOS®

X-SX-SSLIDE seals K08-DD description / technical data

Technical data

Advantages

General description





The specified data represent maximum values and should not be used simultaneously.If in doubt, please contact our technical department. Please also note our liabilityexclusion (page 63).

Detail X-SLIDE seal K08-D

- ggood static and dynamic sealing effect (reduced piston drift)- hhigh wear resistance (high operational reliability)- ooutstanding extrusion resistance (allowing higher pressure / larger

gap sizes)- ccompact design (for small installation height)- llow friction, superior stick-sslip characteristics, high efficiency- eeasy installation procedure (due to higher flexibility of X-ECOPUR®

materials)- ffast pressurisation, no “blow-bby” effect (due to implemented

lateral slots in sealing ring)- qquick delivery within days (or even hours), not weeks


High performance piston seals are essential in almost all equipments. The constantly increasing technological and environmentalrequirements - especially with regard to sealing effect, wear resistance and installation properties - led ECONOMOS® to developthe special X-SLIDE seal range. These newly developed materials together with the optimised geometric design meet all the aboverequirements. Especially on the piston the installation of the seal is not always easy. In the case of conventional PTFE seals, spe-cial mounting and calibration tools are necessary; with X-ECOPUR® materials, installation in most cases can be done by hand - noextra tools or calibration necessary. Profile K08-D is the standard double acting piston seal design.

rd dimensions

D - 4,9D - 7,5

D - 11,0D - 15,5D - 21,0D - 24,5D - 28,0D - 38,0

8 - 14,915 - 39,940 - 79,9

80 - 132,9133 - 329,9330 - 669,9670 - 999,91000 - 3000

2,23,24,26,38,18,19,5

13,8

0,40,61,01,31,81,82,53,0

2,53,54,55,06,08,0

10,012,0

1,782,623,535,37,07,08,4

12,0

0,30,40,50,50,70,70,81,1

0,30,30,40,40,50,50,70,8

0,20,20,30,30,40,40,50,7

0,10,10,20,20,20,20,30,4

BoreØ D

GrooveØ d

Height L

Radiusr

Lead-inc

O-ringCord dia.


SLIDEHousing recommendation

Table of recommended X-SSLIDE seals K08-DD standard dimensions

• The above table shows our standard recommendations. Other dimensions - usually known as “light” and “heavy” series - are included in the tables on the following pages.• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.* specified extrusion gap valid up to temp. 80 °C, between 80 and 100 °C the gap size has to be lowered by 25%


X-SLIDE K08-D, standard application, actual bore diameter: ØD=55 mm, predetermined or choosen housing dimensions (from list "K08-D available standard dimensions”) --> Ød=44,0 mm, L=4,2 mmrequired material: XS-ECOPUR / NBR70 --> article number: 3XR0390 (from list "K08-D available standard dimensions”, article-no.-row 3 for material combination XS-PU/NBR70)


X-SLIDE K08-D, standard application, bore diameter ØD=203,2 mm (8”)housing diameter Ød=ØD - 21,0 = 182,2 mm and housing height L= 8,1 mm (from table “recommended K08-D standard dimen-sions for diameter range Ød 133 - 329,9 mm), required material: XS-ECOPUR / NBR70 --> article number: not available, hou-sing dimension D x d x L followed by material combination should be used for designation:

X-SLIDE K08-D 3XP0390Seal type article no.


Required designation for placing an order: X-SLIDE K08-D 203,2 x 182,2 x 8,1mm XS-PU / NBR70Seal type housing dimensions material combination

For technical advice related to other housing configurations or non standard applications, please use fax enquiry form for piston sealson page 61.

25 ECONOMOS®

X-SSLIDE seals K08-DD basic information

+0,2



Groove face < 15 < 3bearing area Tp 50% - 95 %

Seal housing tolerancesØ d h10Ø D H9

X-S

26 ECONOMOS®

3,15,17,19,17,5

11,18,513,110,515,112,513,5

17,114,516,520,117,514,020,522,527,124,521,027,524,028,530,531,532,529,031,034,037,042,539,034,541,042,044,046,047,049,051,052,047,554,057,059,054,564,059,568,069,064,5

8,010,012,014,015,0

16,0*16,0*18,018,0

20,0*20,0*21,0

22,022,024,025,0

25,0*25,0*28,030,032,0

32,0*32,0*35,035,036,038,039,0

40,0*40,0*42,045,048,050,0

50,0*50,0*52,053,055,057,058,060,062,0

63,0*63,0*65,068,070,070,075,075,079,0

80,0*80,0*

2,22,22,22,23,22,23,22,23,22,23,23,2

2,23,23,22,23,24,23,23,22,23,24,23,24,23,23,23,23,24,24,24,24,23,24,26,34,24,24,24,24,24,24,24,26,34,24,24,26,34,26,34,24,26,3

1XP00101XP00201XP00301XP00401XP00501XP00601XP00701XP00801XP00901XP01001XP01101XP0120

1XP01301XP01401XP01501XP01601XP01701XP01801XP01901XP02001XP02101XP02201XP02301XP02401XP02501XP02601XP02701XP02801XP02901XP03001XP03101XP03201XP03301XP03401XP03501XP03601XP03701XP03801XP03901XP04001XP04101XP04201XP04301XP04401XP04501XP04601XP04701XP04801XP04901XP05001XP05101XP05201XP05301XP0540





------------

------------------------------------------

BoreØ D

GrooveØ d

Height L





X-SLIDE seals K08-D available standard dimensions / article numbers

NOTE: due to our innovative manufacturing process we are able to produce any other dimension in betweenthis standard diameter range. For further information please contact our application engineers


SLIDE

27 ECONOMOS®

59,067,069,564,079,074,569,084,079,574,089,084,579,094,089,584,092,599,094,589,099,594,0

109,0104,5

99,0114,0109,5104,0111,5114,5109,0121,0114,0124,5119,0129,5124,0134,5129,0134,0144,5139,0144,0149,0154,0164,5159,0164,0169,0178,5174,0184,5179,0184,0

80,082,585,085,090,090,090,095,095,095,0

100,0100,0*100,0105,0105,0105,0108,0110,0110,0110,0115,0115,0120,0120,0

120,0125,0

125,0*125,0*127,0130,0130,0132,0135,0140,0140,0145,0145,0150,0150,0155,0

160,0*160,0*165,0170,0175,0180,0180,0185,0190,0194,0195,0

200,0*200,0*205,0

8,16,36,38,14,26,38,14,26,38,14,26,38,14,26,38,16,34,26,38,16,38,14,26,3

8,14,26,38,16,36,38,14,28,16,38,16,38,16,38,18,16,38,18,18,18,16,38,18,18,16,38,16,38,18,1

1XP05501XP05601XP05701XP05801XP05901XP06001XP06101XP06201XP06301XP06401XP06501XP06601XP06701XP06801XP06901XP07001XP07101XP07201XP07301XP07401XP07501XP07601XP07701XP0780

1XP07901XP08001XP08101XP08201XP08301XP08401XP08501XP08601XP08701XP08801XP08901XP09001XP09101XP09201XP09301XP09401XP09501XP09601XP09701XP09801XP09901XP10001XP10101XP10201XP10301XP10401XP10501XP10601XP10701XP1080





------------------------

------------------------------

BoreØ D

GrooveØ d

Height L








X-S

28 ECONOMOS®

189,0194,0199,0204,0214,5209,0219,0234,5229,0225,5239,0244,0

247,0249,0259,0269,0279,0275,5289,0299,0295,5305,5315,5325,5335,5345,5355,5365,5375,5385,5

210,0215,0220,0225,0230,0230,0240,0250,0

250,0*250,0*260,0265,0

268,0270,0280,0290,0300,0300,0310,0

320,0*320,0*330,0340,0350,0360,0370,0380,0390,0

400,0*410,0

8,18,18,18,16,38,18,16,38,18,18,18,1

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,1


1XP12101XP12201XP12301XP12401XP12501XP12601XP12701XP12801XP12901XP13001XP13101XP13201XP13301XP13401XP13501XP13601XP13701XP1380





------------

------------------

BoreØ D

GrooveØ d

Height L








SLIDE

29 ECONOMOS®

395,5405,5415,5425,5435,5445,5455,5465,5475,5530,5575,5615,5635,5672,0682,0712,0752,0772,0872,0972,0962,0

1022,01027,01032,01172,01162,01187,01462,01962,02462,02662,02962,0

420,0430,0440,0450,0460,0470,0480,0490,0

500,0*555,0600,0640,0660,0700,0710,0740,0780,0800,0900,0

1000,01000,01050,01065,01070,01200,01200,01225,01500,02000,02500,02700,03000,0

8,18,18,18,18,18,18,18,18,18,18,18,18,19,59,59,59,59,59,59,5

13,89,5

13,813,89,5

13,813,813,813,813,813,813,8

1XP13901XP14001XP14101XP14201XP14301XP14401XP14501XP14601XP14701XP1480

----------------------


----------------------


----------------------

----------

4XP14904XP15004XP15104XP15204XP15304XP15404XP15504XP15604XP15704XP15804XP15904XP16004XP16104XP16204XP16304XP16404XP16504XP16604XP16704XP16804XP16904XP1700

BoreØ D

GrooveØ d

Height L







K08-DS standa

30 ECONOMOS®

X-SX-SSLIDE seals K08-DDS description / technical data

Technical data

Advantages

General description






Detail X-SLIDE seal K08-DS

- ggood static and dynamic sealing effect (reduced piston drift)- hhigh wear resistance (high operational reliability)- ooutstanding extrusion resistance (allowing higher pressure / larger

gap sizes)- ccompact design (for small installation height)- ccompact, stable square energizer ring profile (less deformation on

pulsating load) - eeasy installation procedure (due to higher flexibility of X-ECOPUR®

materials)- ffast pressurisation, no “blow-bby” effect (due to implemented



X-SLIDE K08-DS seal is a "heavy duty" double acting piston seal consisting of an X-ECOPUR® sealing element and an elastomericsquare profile ring energizer element. Interference fit and preload of energizing element ensures a good initial sealing effect.Designed with a square section energizer ring for increased stability and less deformation of the energizer. Especially on the piston,the installation of the seal is not always easy. In the case of conventional PTFE seals, special mounting and calibration tools arenecessary with X-ECOPUR® materials, installation in most cases can be done by hand - no extra tools or calibration necessary.

31 ECONOMOS®

ard dimensions

D - 10D - 15D - 20D - 25D - 30D - 35D - 40

20 - 49,950 - 59,9

60 - 199,9200 - 299,9300 - 529,9530 - 679,9680 - 1500

5,07,5

10,012,515,017,520,0

0,30,40,40,40,81,21,2

4,05,06,08,5

10,013,015,0

BoreØ D

GrooveØ d

Height L

Radiusr

Lead-inc



Table of recommended X-SSLIDE seals K08-DDS standard dimensions

• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.* specified extrusion gap valid up to temp. 80 °C, between 80 and 100 °C the gap size has to be lowered by 25%


X-SLIDE K08-DS, standard application, actual bore diameter: ØD=210 mm, predetermined or chosen housing dimensions (from list "K08-DS available standard dimensions”) --> Ød=185 mm, L=12,5 mmrequired material: X-ECOPUR / NBR85 --> article number: 1XPH0210 (from list "K08-DS available standard dimensions”, article-no.-row 1 for material combination X-PU/NBR85)


X-SLIDE K08-DS, standard application, bore diameter ØD=209,55 mm (8 1/4”)housing diameter Ød=ØD - 25 = 184,55 mm and housing height L= 12,5 mm (from table “recommended K08-DS standard dimen-sions for diameter range ØD 200 - 299,9 mm), required material: X-ECOPUR / NBR85 --> article number: not available, housingdimension D x d x L followed by material combination should be used for designation:

X-SLIDE K08-DS 1XPH0210Seal type article no.

Required designation for placing an order: X-SLIDE K08-DS 209,55 x 184,55 x 12,5mm X-PU / NBR85Seal type housing dimensions material combination



SLIDEX-SSLIDE seals K08-DDS basic information

0,50,50,70,80,91,01,1

0,40,40,50,60,70,80,9

0,30,30,40,50,60,70,8

0,20,20,20,30,30,30,4

+0,2





X-S

32 ECONOMOS®

101520222530353540

40,043,050,060,080,095,0

105,0120,0130,0160,0175,0185,0195,0205,0215,0

220,0225,0235,0245,0250,0255,0255,0265,0270,0275,0280,0290,0300,0310,0320,0330,0340,0350,0360,0370,0380,0390,0400,0420,0450,0460,0470,0490,0495,0515,0

202530323540455055

60,063,070,080,0

100,0115,0125,0140,0150,0180,0200,0210,0220,0230,0240,0

245,0250,0260,0270,0275,0280,0285,0290,0300,0305,0310,0320,0330,0340,0350,0360,0370,0380,0390,0400,0410,0420,0430,0450,0480,0490,0500,0520,0530,0550,0

5555555

7,57,5

10,010,01010101010101010

12,512,512,512,512,5

12,512,512,512,512,512,512,512,51515151515151515151515151515151515151515

17,517,5

1XPH00101XPH00201XPH00301XPH00401XPH00501XPH00601XPH00701XPH00801XPH00901XPH01001XPH01101XPH01201XPH01301XPH01401XPH01501XPH01601XPH01701XPH01801XPH01901XPH02001XPH02101XPH02201XPH02301XPH0240

1XPH02501XPH02601XPH02701XPH02801XPH02901XPH03001XPH03101XPH03201XPH03301XPH03401XPH03501XPH03601XPH03701XPH03801XPH03901XPH04001XPH04101XPH04201XPH04301XPH04401XPH04501XPH04601XPH04701XPH04801XPH04901XPH05001XPH05101XPH05201XPH05301XPH0540





------------------------

------------------------------

BoreØ D

GrooveØ d

Height L





X-SLIDE seals K08-DS available standard dimensions / article numbers


SLIDE525,0535,0545,0555,0565,0575,0585,0595,0605,0615,0625,0635,0640,0650,0670,0680,0690,0700,0710,0720,0730,0740,0760,0780,0

790,0800,0810,0840,0860,0880,0900,0910,0925,0940,0960,0

1.010,01.060,01.080,01.100,01.140,01.260,01.360,01.410,01.460,0

560,0570,0580,0590,0600,0610,0620,0630,0640,0650,0660,0670,0680,0690,0710,0720,0730,0740,0750,0760,0770,0780,0800,0820,0

830,0840,0850,0880,0900,0920,0940,0950,0965,0980,0

1.000,01.050,01.100,01.120,01.140,01.180,01.300,01.400,01.450,01.500,0

17,517,517,517,517,517,517,517,517,517,517,517,5202020202020202020202020

2020202020202020202020202020202020202020

1XPH05501XPH05601XPH05701XPH0580

--------------------

--------------------

2XPH05502XPH05602XPH05702XPH0580

--------------------

--------------------

3XPH05503XPH05603XPH05703XPH0580

--------------------

--------------------

----

4XPH05904XPH06004XPH06104XPH06204XPH06304XPH06404XPH06504XPH06604XPH06704XPH06804XPH06904XPH07004XPH07104XPH07204XPH07304XPH07404XPH07504XPH07604XPH07704XPH0780

4XPH07904XPH08004XPH08104XPH08204XPH08304XPH08404XPH08504XPH08604XPH08704XPH08804XPH08904XPH09004XPH09104XPH09204XPH09304XPH09404XPH09504XPH09604XPH09704XPH0980

BoreØ D

GrooveØ d

Height L





X-SLIDE seals K08-DS available standard dimensions / article numbers


33 ECONOMOS®

34 ECONOMOS®

Introductionma

General description F-SSLIDE seal range

ECONOMOS® "F-SLIDE seal range" is the standard family of elastomerically energizedsealing elements in various PTFE compounds. The vast majority of applications can notonly be met, but also improved with our new developed X-SLIDE seal range. However,there are still applications remaining where non-standard operating conditions requirePTFE solutions either because of its excellent high temperature resistance or ultimatechemical resistance. The characteristics of PTFE materials do not allow seals made ofthis material to meet ultimate sealing performance, therefore most rod sealing systemsconsist of a "tandem arrangement" (two F-SLIDE seals S09-E behind each other) or a com-bination of a primary F-SLIDE S09-E seal and a secondary polyurethane lip seal style (e.g.ECONOMOS® S01-P profile) to reach acceptable leakage behaviour. For critical sealingapplications the use of a double acting wiper behind the seals and a "leakage vent" in bet-ween can upgrade the leakage performance.

In the case of standard double acting piston seals which are energized from both sideswith the same media, any occurring small leakage is not visible, indeed it could createsome additional lubrication for better friction and wear behaviour and is acceptable aslong as performance efficiency is not influenced. If a critical holding function is required, or if the piston seal has to separate differentmedia, an efficient sealing effect can only be reached if an additional elastomeric sealingelement is implemented into the PTFE sealing element (see special solutions on page 59).

The combination of our own PTFE manufacturing plant in the ECONOMOS® group and theintensive in-house research and development programme (including material and test riginvestigations), assure optimised material characteristics on our standard range of PTFEmaterials. Additionally we can offer non-standard sealing solutions in special customizedcompounds.

Owing to our own PTFE manufacturing plant we are able to offer a wide range of specialPTFE compounds, for instance, PTFE filled with various percentages of carbon, graphite,glass fibre, PEEK, polyimide, and many more. Please contact our technical department formore information on which PTFE compound is best suitable for your specific application.

Over many years ECONOMOS® has shown its commitment towards designing and deve-loping the absolute best in materials and profiles. Our highly trained and experiencedsales and application engineers are focused on providing answers to your questions andsolutions to your specific needs.

General descriptionF-SLIDE seal range

Further PTFE compounds for F-SLIDE seals

Summary

35 ECONOMOS®

standard/specia

ateriaMaterial combinations for F-SSLIDE seals

ECOFLON 2 / NBR70*grey black

ECOFLON 2 / FKM70**grey black (brown)

ECOFLON 3 / NBR70*light green up to Ø 600 mm blackbronze above Ø 600 mm black

ECOFLON 3 / FPM70**light green up to Ø 600 mm black (brown)bronze above Ø 600 mm black (brown)

-30°C to +100°C

-20°C to +200°C

-30°C to +100°C

-20°C to +200°C

PTFE filled with 15% glass fibre and 5% MoS2

for mineral oils, hydraulic fluids of the group HFA, HFB, HFCand most biologically degradable fluids (bio-oils). Owing toNBR (Rubber) energizer, limited temperature resistance.

PTFE filled with 15% glass fibre and 5% MoS2

for mineral oils, hydraulic fluids of the group HFA, HFB, HFCand most biologically degradable fluids (bio-oils). Owing toFKM (Viton®) energizer, increased temperature resistance.

PTFE filled with 40% BronzeStandard material for mineral oil based hydraulic fluids and bio-logically degradable fluids (Bio-oils). Owing to NBR (Rubber)energizer, limited temperature resistance.

PTFE filled with 40% BronzeStandard material for mineral oil based hydraulic fluids. Owingto FKM (Viton®) energizer, increased temperature resistance.Suitable for biologically degradable fluids (Bio-oils) and hydrau-lic fluids of the HFD group.

Standard material combinations

* ECORUBBER 1 (NBR 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS** ECORUBBER 2 (FKM 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS

ECOFLON 4 / NBR70*dark grey black

ECOFLON 4 / FKM70**dark grey black (brown)

-30°C to +100°C

-20°C to +200°C

PTFE filled with 25% Carbon for mineral oils, hydraulic fluids of the group HFA, HFB, HFC andmost biologically degradable fluids (bio-oils). Suitable for softmetal gliding surfaces as well as pneumatic applications. Owingto NBR (Rubber) energizer, limited temperature resistance.

PTFE filled with 25% Carbon for mineral oils, hydraulic fluids of the group HFA, HFB, HFC andmost biologically degradable fluids (bio-oils). Suitable for softmetal gliding surfaces as well as pneumatic applications. Owingto FKM (Viton®) energizer, increased temperature resistance.

Special material combinations

* ECORUBBER 1 (NBR 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS** ECORUBBER 2 (FKM 85 Shore A) as energiser material for heavy duty design S09-ES, K08-DS

Due to the excellent chemical and temperature resistance of PTFE materials, this group of seals can be "adjusted" to almostevery application by selecting the appropriate energizer material. ECONOMOS® can offer, for example, H-NNBR, H-NNBR low tem-perature grade, silicone, EPDM, and many more. Please consult our technical department for further information.

S09-E standard

F-S

36 ECONOMOS®

F-SSLIDE seals S09-EE description / technical data

Technical data

Advantages

General description




* see material combinations for F-SLIDE seals on page 35


Detail F-SLIDE seal S09-E

- vvery low friction, superior stick-sslip behaviour- nno adhesive effect to metal parts after prolonged periods of standstill - ssuitable for under lubricated systems (material dependence)- eexcellent temperature resistance (depending on selected '0' ring

material)- eexcellent chemical resistance (depending on selected '0' ring

material)- ccompact design (for small installation height)- qquick delivery within days (or even hours), not weeks

(depending on diameter and quantity)- aavailable as individual single piece or medium lot production- aavailable in large quantities - aavailable for all diameters up to 3.000 mm

F-SLIDE S09-E seal is the standard single acting rod seal consisting of a PTFE compound sealing element and an elastomeric '0' ringenergizer element. Interference fit and '0' ring preload ensure a good initial sealing effect. Increasing system pressure further ener-gizes the '0' ring for higher contact force and proportionally better sealing. By selecting a suitable '0' ring material, the seal can be"adjusted" to suit various chemical and thermal conditions (see material combinations for F-SLIDE seal on page 35). This seal styleis always used in so called "tandem" arrangements or in combination with a lip seal (see page 11).

37 ECONOMOS®

d dimensions

SLIDEF-SSLIDE seals S09-EE basic information

• The above table shows our standard recommendations. Other dimensions - usually known as “light” and “heavy” series - are included in the tables on the following pages.• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.

d + 4,9d + 7,3

d + 10,7d + 15,1d + 20,5d + 24,0d + 27,3d + 38,0

3 - 7,98 - 18,9

19 - 37,938 - 199,9

200 - 255,9256 - 649,9650 - 999,91000 - 3000

2,23,24,26,38,18,19,5

13,8

0,40,61,01,31,81,82,53,0

2,53,54,55,06,08,0

10,012,0

1,782,623,535,337,007,008,40

12,00

0,300,400,400,500,600,600,701,00

0,200,250,250,300,350,350,500,70

0,150,150,200,200,250,250,300,60

0,050,050,100,100,150,150,200,30

RodØ d

GrooveØ D

Height L

Radiusr

Lead-inc

O-ringCord dia.

max. radial extrusion gap “s”100 bar 200 bar 400 bar 600 bar


F-SLIDE S09-E, standard application, actual rod diameter: Ød=22 mm, predetermined or chosen housing dimensions (from list "S09-E available standard dimensions”) --> ØD=32,7mm, L=4,2mm requi-red material: ECOFLON 3 / NBR70 --> article number: 3FR0390 (from list "S09-E available standard dimensions”, article-no.-row 3 for material combination ECOFLON 3/NBR70)


F-SLIDE S09-E, standard application, rod diameter Ød=25,4 mm (1”)housing diameter ØD=Ød+10,7 = 36,1mm and housing height L= 4,2 mm (from table “recommended S09-E standard dimensionsfor diameter range Ød 19 - 37,9 mm), required material: ECOFLON 3 / NBR70 --> article number: not available, housing dimen-sion d x D x L followed by material combination should be used for designation:

F-SLIDE S09-E 3FR0390Seal type article no.


Required designation for placing an order: F-SLIDE S09-E 25,4 x 36,1 x 4,2mm FLON 3 / NBR70Seal type housing dimensions material combination



Table of recommended F-SSLIDE seals S09-EE standard dimensions





+0,2+0,2

F-S

38 ECONOMOS®

7,98,99,9

10,911,011,912,913,015,313,916,314,915,017,316,917,019,319,5

18,919,021,321,519,922,320,923,323,521,922,925,325,529,727,327,530,731,029,329,532,733,031,332,332,535,736,033,336,739,035,338,737,340,739,342,7

3,04,05,06,06,0*7,08,0

8,0*8,09,09,0

10,010,0*10,012,0

12,0*12,012,0*

14,014,0*14,014,0*15,015,016,016,016,0*17,018,018,018,0*19,020,0

20,0*20,020,0*22,0

22,0*22,022,0*24,025,0

25,0*25,025,0*26,026,0

28,0*28,028,030,030,032,032,0

2,22,22,22,22,22,22,22,23,22,23,22,22,23,22,22,23,23,2

2,22,23,23,22,23,22,23,23,22,22,23,23,24,23,23,24,24,23,23,24,24,23,23,23,24,24,23,24,24,23,24,23,24,23,24,2

1FR00101FR00201FR00301FR00401FR00501FR00601FR00701FR00801FR00901FR01001FR01101FR01201FR01301FR01401FR01501FR01601FR01701FR0180

1FR01901FR02001FR02101FR02201FR02301FR02401FR02501FR02601FR02701FR02801FR02901FR03001FR03101FR03201FR03301FR03401FR03501FR03601FR03701FR03801FR03901FR04001FR04101FR04201FR04301FR04401FR04501FR04601FR04701FR04801FR04901FR05001FR05101FR05201FR05301FR0540







RodØ d

GrooveØ D

Height L

Article-Nr.Flon 2/NBR70

Article-Nr.Flon 2/FKM70



F-SLIDE seals S09-E available standard dimensions / article numbers



SLIDE43,042,345,743,346,747,044,347,748,753,150,751,055,152,757,153,755,756,060,158,763,160,761,065,162,767,169,165,770,166,767,071,171,576,572,169,770,775,173,774,078,178,5

75,780,177,784,180,785,185,590,582,788,185,790,1

32,0*35,035,036,036,0

36,0*37,037,038,038,040,0

40,0*40,042,042,043,045,0

45,0*45,048,048,050,0

50,0*50,052,052,054,055,055,056,0

56,0*56,056,0*56,057,059,060,060,063,0

63,0*63,063,0*

65,065,067,069,070,070,070,0*70,072,073,075,075,0

4,23,24,23,24,24,23,24,24,26,34,24,26,34,26,34,24,24,26,34,26,34,24,26,34,26,36,34,26,34,24,26,36,38,16,34,24,26,34,24,26,36,3

4,26,34,26,34,26,36,38,14,26,34,26,3

1FR05501FR05601FR05701FR05801FR05901FR06001FR06101FR06201FR06301FR06401FR06501FR06601FR06701FR06801FR06901FR07001FR07101FR07201FR07301FR07401FR07501FR07601FR07701FR07801FR07901FR08001FR08101FR08201FR08301FR08401FR08501FR08601FR08701FR08801FR08901FR09001FR09101FR09201FR09301FR09401FR09501FR0960

1FR09701FR09801FR09901FR10001FR10101FR10201FR10301FR10401FR10501FR10601FR10701FR1080







RodØ d

GrooveØ D

Height L








39 ECONOMOS®

F-S

40 ECONOMOS®

93,190,795,195,5

100,597,693,795,7

100,1105,5104,1100,7105,1105,5110,5102,7107,1105,7

110,1110,7115,1115,5120,5120,1125,5120,7125,1125,5130,5130,1135,1140,5140,1140,5145,5142,1145,1150,5147,1145,7150,1152,1153,1150,7155,1155,5160,5155,6160,1165,5165,1170,5168,1170,1

78,080,080,080,0*80,082,583,085,085,085,089,090,090,090,0*90,092,092,095,0

95,0100,0100,0100,0*100,0105,0105,0110,0110,0110,0*110,0115,0120,0120,0125,0125,0*125,0127,0130,0130,0132,0135,0135,0137,0138,0140,0140,0140,0*140,0140,5145,0145,0150,0150,0153,0155,0

6,34,26,36,38,16,34,24,26,38,16,34,26,36,38,14,26,34,2

6,34,26,36,38,16,38,14,26,36,38,16,36,38,16,36,38,16,36,38,16,34,26,36,36,34,26,36,38,16,36,38,16,38,16,36,3









RodØ d

GrooveØ D

Height L








SLIDE175,1175,5180,5181,0180,1185,1190,5188,1190,1195,1195,5200,5201,0200,1205,5205,1210,5210,1215,1220,5221,0225,5230,5231,5232,5235,5240,5241,0245,5245,1250,5255,5260,5265,5270,5271,0

284,0289,0290,5294,0299,0304,5304,0309,0314,0319,0320,5324,0334,0344,5344,0354,0364,0370,5

160,0160,0*160,0

160,0*165,0170,0170,0173,0175,0180,0180,0*180,0

180,0*185,0185,0190,0190,0195,0200,0200,0200,0*205,0210,0211,0212,0215,0220,0220,0*225,0230,0230,0235,0240,0245,0250,0250,0*

260,0265,0270,0270,0275,0

280,0*280,0285,0290,0295,0300,0300,0310,0

320,0*320,0330,0340,0350,0

6,36,38,18,16,36,38,16,36,36,36,38,18,16,38,16,38,16,36,38,18,18,18,18,18,18,18,18,18,16,38,18,18,18,18,18,1

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,1









RodØ d

GrooveØ D

Height L








41 ECONOMOS®

F-S374,0384,0384,5389,0394,0399,0404,0414,0424,0434,0444,0454,0459,0464,0474,0484,0494,0504,0

509,0514,0524,0534,0544,0549,0554,0564,0574,0584,0594,0604,0609,0614,0624,0634,0644,0654,0664,0677,3683,3687,3697,3707,3712,3717,3724,0727,3737,3747,3757,3762,3767,3777,3787,3792,3

350,0360,0360,0*365,0370,0375,0380,0390,0400,0410,0420,0430,0435,0440,0450,0460,0470,0480,0

485,0490,0500,0510,0520,0525,0530,0540,0550,0560,0570,0580,0585,0590,0600,0610,0620,0630,0640,0650,0656,0660,0670,0680,0685,0690,0700,0700,0710,0720,0730,0735,0740,0750,0760,0765,0

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,1

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,19,59,59,59,59,59,59,58,19,59,59,59,59,59,59,59,59,5









RodØ d

GrooveØ D

Height L








42 ECONOMOS®

SLIDE797,3807,3817,3822,3827,3837,3847,3857,3867,3877,3887,3897,3907,3912,3917,3927,3937,3947,3

957,3967,3977,3982,3

1.038,01.073,01.067,31.078,01.077,31.088,01.138,01.147,31.158,01.227,31.238,01.357,31.368,01.477,31.527,31.538,01.638,02.038,02.638,03.038,0

770,0780,0790,0795,0800,0810,0820,0830,0840,0850,0860,0870,0880,0885,0890,0900,0910,0920,0

930,0940,0950,0955,0

1.000,01.035,01.040,01.040,01.050,01.050,01.100,01.120,01.120,01.200,01.200,01.330,01.330,01.450,01.500,01.500,01.600,02.000,02.600,03.000,0

9,59,59,59,59,59,59,59,59,59,59,59,59,59,59,59,59,59,5

9,59,59,59,5

13,813,89,5

13,89,5

13,813,89,5

13,89,5

13,89,5

13,89,59,5

13,813,813,813,813,8


1FR28901FR29001FR29101FR29201FR29301FR29401FR29501FR29601FR29701FR29801FR29901FR30001FR30101FR30201FR30301FR30401FR30501FR30601FR30701FR30801FR30901FR31001FR31101FR3120







RodØ d

GrooveØ D

Height L








43 ECONOMOS®

S09-ES standa

F-S

44 ECONOMOS®

F-SSLIDE seals S09-EES description / technical data

Technical data

Advantages

General description






Detail F-SLIDE seal S09-ES

- vvery low friction, superior stick-sslip behaviour- nno adhesive effect to metal parts after prolonged periods of standstill- ssuitable for under lubricated systems (material dependence)- eexcellent temperature resistance (depending on selected '0'ring

material)- eexcellent chemical resistance (depending on selected '0'ring

material)- ccompact design (for small installation height)- ccompact, stable square energizer ring profile (less deformation on

pulsating load)- qquick delivery within days (or even hours), not weeks

(depending on diameter and quantity)- aavailable as individual single piece or medium lot production- aavailable in large quantities- aavailable for all diameters up to 1.500 mm

F-SLIDE S09-ES seal is a "heavy duty" single acting rod seal consisting of a PTFE compound sealing element and an elastomeric squa-re profile energizer element. Interference fit and preload of energizing element ensure a good sealing effect. Designed with a squa-re energizer profile ring for increased stability and reduced deformation of the energizer ring under pulsating load. By selecting a sui-table energizer material, the seal can be "adjusted" to suit various chemical and thermal conditions (see material combinations for F-SLIDE seal on page 35). This seal style is generally used in so called "tandem" arrangements or in combination with a lip seal (seepage 11).

45 ECONOMOS®

ard dimensions


Table of recommended F-SSLIDE seals S09-EES standard dimensions

• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.


F-SLIDE S09-ES, standard application, actual rod diameter: Ød=125 mm, predetermined or chosen housing dimensions (from list "S09-ES available standard dimensions”) --> ØD=145mm, L=10mm requi-red material: ECOFLON 2 / FKM85 --> article number: 2FRH0300 (out of list "S09-ES available standard dimensions”, article-no.-row 2 for material combination ECOFLON 2/FKM85)


F-SLIDE S09-ES, standard application, rod diameter Ød=101,6 mm (4”)housing diameter ØD=Ød+20 = 121,6 mm and housing height L= 10,0 mm (from table “recommended S09-ES standard dimensionsfor diameter range Ød 60 - 199,9 mm), required material: ECOFLON 2 / NBR85 --> article number: not available, housing dimen-sion d x D x L followed by material combination should be used for designation:

F-SLIDE S09-ES 2FRH0300Seal type article no.

Required designation for placing an order: F-SLIDE S09-ES 101,6 x 121,6 x 10 mm FLON 2 / NBR85Seal type housing dimensions material combination



F-SSLIDE seals S09-EES basic information

d + 10d + 15d + 20d + 25d + 30d + 35d + 40

5 - 49,950 - 59,9

60 - 199,9200 - 299,9300 - 529,9530 - 679,9680 - 1500

5,07,5

10,012,515,017,520,0

0,20,30,40,40,81,21,2

4,05,06,08,5

10,011,513,0

0,300,300,400,400,500,600,70

0,400,500,600,600,700,801,00

0,200,200,250,250,300,500,60

0,100,100,150,150,200,200,30

RodØ d

GrooveØ D

Height L

Radiusr

Lead-inc






+0,2 +0,2

F-S

46 ECONOMOS®

15202226

30,035,038,042,046,050,052,055,058,065,067,069,070,071,080,083,085,090,095,0

100,0105,0110,0115,0120,0130,0145,0

160,0170,0180,0175,0195,0200,0225,0245,0255,0265,0275,0295,0305,0315,0330,0340,0350,0355,0360,0370,0380,0390,0410,0420,0

5101216

20,025,028,032,036,040,042,045,048,050,052,054,055,056,060,063,065,070,075,080,085,090,095,0

100,0110,0125,0

140,0150,0160,0170,0175,0180,0200,0220,0230,0240,0250,0270,0280,0290,0300,0310,0320,0325,0330,0340,0350,0360,0380,0390,0

5555555555555

7,57,57,57,57,5101010101010101010101010

101010101010

12,512,512,512,512,512,512,512,515151515151515151515

1FRH00101FRH00201FRH00301FRH00401FRH00501FRH00601FRH00701FRH00801FRH00901FRH01001FRH01101FRH01201FRH01301FRH01401FRH01501FRH01601FRH01701FRH01801FRH01901FRH02001FRH02101FRH02201FRH02301FRH02401FRH02501FRH02601FRH02701FRH02801FRH02901FRH0300

1FRH03101FRH03201FRH03301FRH03401FRH03501FRH03601FRH03701FRH03801FRH03901FRH04001FRH04101FRH04201FRH04301FRH04401FRH04501FRH04601FRH04701FRH04801FRH04901FRH05001FRH05101FRH05201FRH05301FRH0540





------------------------------

------------------------

RodØ d

GrooveØ D

Height L

Article-Nr.Flon2/NBR85





F-SLIDE seals S09-ES available standard dimensions / article numbers

SLIDE

47 ECONOMOS®

430,0440,0450,0460,0470,0480,0490,0500,0510,0520,0530,0540,0550,0565,0575,0585,0595,0605,0

615,0625,0635,0655,0685,0695,0705,0720,0740,0760,0780,0795,0810,0840,0860,0890,0940,0990,0

1.010,01.040,01.190,01.240,01.370,01.540,0

400,0410,0420,0430,0440,0450,0460,0470,0480,0490,0500,0510,0520,0530,0540,0550,0560,0570,0

580,0590,0600,0620,0650,0660,0670,0680,0700,0720,0740,0755,0770,0800,0820,0850,0900,0950,0970,0

1.000,01.150,01.200,01.330,01.500,0

15151515151515151515151515

17,517,517,517,517,5

17,517,517,517,517,517,517,52020202020202020202020202020202020

1FRH05501FRH05601FRH05701FRH05801FRH05901FRH06001FRH06101FRH0620

----------

------------------------


----------

------------------------


----------

------------------------

--------

4FRH06304FRH06404FRH06504FRH06604FRH06704FRH06804FRH06904FRH07004FRH07104FRH0720


RodØ d

GrooveØ D

Height L





F-SLIDE seals S09-ES available standard dimensions / article numbers


K08-D standar

48 ECONOMOS®

F-SF-SSLIDE seals K08-DD description / technical data

Technical data

Advantages

General description






Detail F-SLIDE seal K08-D

- vvery low friction, superior stick-sslip behaviour- nno adhesive effect to metal parts after prolonged periods of standstill- ssuitable for under lubricated systems (material dependent)- eexcellent temperature resistance (depending on selected '0'ring


material)- ccompact design (for small installation height)- ffast pressurisation, no “blow-bby” effect (due to implemented


(depending on diameter and quantity)- aavailable as individual single piece or limited-llot production- aavailable in large quantities- aavailable for all diameters up to 3.000 mm

F-SLIDE K08-D seal is a double acting piston seal consisting of a PTFE compound sealing element and an elastomeric '0'ring ener-gizer element. Interference fit and '0'ring preload ensure a good initial sealing effect. Increasing system pressure energizes the'0'ring additionally for higher contact force and proportionally better sealing. By selecting suitable '0'ring materials, the seal can be"adjusted" to suit various chemical and thermal conditions. (see material combinations for F-SLIDE seal on page 35). Profile K08-Dis the standard double acting piston seal design.

S09-E standard dimensions

49 ECONOMOS®

rd dimensions

D - 4,9D - 7,5

D - 11,0D - 15,5D - 21,0D - 24,5D - 28,0D - 38,0

8 - 14,915 - 39,940 - 79,9

80 - 132,9133 - 329,9330 - 669,9670 - 999,91000 - 3000

2,23,24,26,38,18,19,5

13,8

0,40,61,01,31,81,82,53,0

2,53,54,55,06,08,0

10,012,0

1,782,623,535,337,07,08,4

12,0

0,300,400,400,500,600,600,701,00

0,200,250,250,300,350,350,500,70

0,150,150,200,200,250,250,300,60

0,050,050,100,100,150,150,200,30

BoreØ D

GrooveØ d

Height L

Radiusr

Lead-inc

O-ringCord dia.



Table of recommended F-SSLIDE seal K08-DD standard dimensions

• The above table shows our standard recommendations. Other dimensions - usually known as “light” and “heavy” series - are included in the tables on the following pages.• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department..


F-SLIDE K08-D, standard application, actual bore diameter: ØD=55 mm, predetermined or chosen housing dimensions (from list "K08-D available standard dimensions”) --> Ød=44,0 mm, L=4,2 mmrequired material: ECOFLON 2 / NBR70 --> article number: 1FP0390 (from list "K08-D available standard dimensions”, article-no.-row 1 for material combination ECOFLON 2/NBR70)


F-SLIDE K08-D, standard application, bore diameter ØD=203,2 mm (8”)housing diameter Ød=ØD - 21,0 = 182,2 mm and housing height L= 8,1 mm (from table “recommended K08-D standard dimen-sions for diameter range Ød 133 - 329,9 mm), required material: ECOFLON 2 / NBR70 --> article number: not available, hou-sing dimension D x d x L followed by material combination should be used for designation:

F-SLIDE K08-D 1FP0390Seal type article no.


Required designation for placing an order: F-SLIDE K08-D 203,2 x 182,2 x 8,1mm FLON 2 / NBR70Seal type housing dimensions material combination


F-SSLIDE seals K08-DD basic information

+0,2





F-S

50 ECONOMOS®

3,15,17,19,17,5

11,18,513,110,515,112,513,5

17,114,516,520,117,514,020,522,527,124,521,027,524,028,530,531,532,529,031,034,037,042,539,034,541,042,044,046,047,049,051,052,047,554,057,059,054,564,059,568,069,064,5

8,010,012,014,015,0

16,0*16,0*18,018,0

20,0*20,0*21,0

22,022,024,025,0

25,0*25,0*28,030,032,0

32,0*32,0*35,035,036,038,039,0

40,0*40,0*42,045,048,050,0

50,0*50,0*52,053,055,057,058,060,062,0

63,0*63,0*65,068,070,070,075,075,079,0

80,0*80,0*

2,22,22,22,23,22,23,22,23,22,23,23,2

2,23,23,22,23,24,23,23,22,23,24,23,24,23,23,23,23,24,24,24,24,23,24,26,34,24,24,24,24,24,24,24,26,34,24,24,26,3

B6,34,24,26,38,1

1FP00101FP00201FP00301FP00401FP00501FP00601FP00701FP00801FP00901FP01001FP01101FP0120

1FP01301FP01401FP01501FP01601FP01701FP01801FP01901FP02001FP02101FP02201FP02301FP02401FP02501FP02601FP02701FP02801FP02901FP03001FP03101FP03201FP03301FP03401FP03501FP03601FP03701FP03801FP03901FP04001FP04101FP04201FP04301FP04401FP04501FP04601FP04701FP04801FP04901FP05001FP05101FP05201FP05301FP0540







BoreØ D

GrooveØ d

Height L





F-SLIDE seals K08-D available standard dimensions / article numbers



SLIDE

51 ECONOMOS®

59,067,069,564,079,074,569,084,079,574,089,084,579,094,089,584,092,599,094,589,099,594,0

109,0104,5

99,0114,0109,5104,0111,5114,5109,0121,0114,0124,5119,0129,5124,0134,5129,0134,0144,5139,0144,0149,0154,0164,5159,0164,0169,0178,5174,0184,5179,0184,0

80,082,585,085,090,090,090,095,095,095,0

100,0100,0*100,0105,0105,0105,0108,0110,0110,0110,0115,0115,0120,0120,0

120,0125,0

125,0*125,0*127,0130,0130,0132,0135,0140,0140,0145,0145,0150,0150,0155,0

160,0*160,0*165,0170,0175,0180,0180,0185,0190,0194,0195,0

200,0*200,0*205,0

6,36,38,14,26,38,14,26,38,14,26,38,14,26,38,16,34,26,38,16,38,14,26,38,1

4,26,38,16,36,38,14,28,16,38,16,38,16,38,18,16,38,18,18,18,16,38,18,18,16,38,16,38,18,18,1

1FP05501FP05601FP05701FP05801FP05901FP06001FP06101FP06201FP06301FP06401FP06501FP06601FP06701FP06801FP06901FP07001FP07101FP07201FP07301FP07401FP07501FP07601FP07701FP0780

1FP07901FP08001FP08101FP08201FP08301FP08401FP08501FP08601FP08701FP08801FP08901FP09001FP09101FP09201FP09301FP09401FP09501FP09601FP09701FP09801FP09901FP10001FP10101FP10201FP10301FP10401FP10501FP10601FP10701FP1080







BoreØ D

GrooveØ d

Height L








F-S189,0194,0199,0204,0214,5209,0219,0234,5229,0225,5239,0244,0

247,0249,0259,0269,0279,0275,5289,0299,0295,5305,5315,5325,5335,5345,5355,5365,5375,5385,5395,5405,5415,5425,5435,5445,5455,5465,5475,5530,5575,5615,5635,5672,0682,0712,0752,0772,0872,0972,0962,0

1022,01027,01032,0

210,0215,0220,0225,0230,0230,0240,0250,0

250,0*250,0*260,0265,0

268,0270,0280,0290,0300,0300,0310,0

320,0*320,0*330,0340,0350,0360,0370,0380,0390,0

400,0*410,0420,0430,0440,0450,0460,0470,0480,0490,0

500,0*555,0600,0640,0660,0700,0710,0740,0780,0800,0900,0

1000,01000,01050,01065,01070,0

8,18,18,16,38,18,16,38,18,18,18,18,1

8,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,18,19,59,59,59,59,59,59,5

13,89,5

13,813,89,5









BoreØ D

GrooveØ d

Height L








52 ECONOMOS®

SLIDE

53 ECONOMOS®

1172,01162,01187,01462,01962,02462,02662,02962,0

1200,01200,01225,01500,02000,02500,02700,03000,0

13,813,813,813,813,813,813,813,8

1FP16301FP16401FP16501FP16601FP16701FP16801FP16901FP1700




BoreØ D

GrooveØ d

Height L







K08-DS standa

54 ECONOMOS®

F-SF-SSLIDE seals K08-DDS description / technical data

Technical data

Advantages

General description






Detail F-SLIDE seal K08-DS

- vvery low friction, superior stick-sslip behaviour- nno adhesive effect to metal parts after prolonged periods of standstill - ssuitable for under lubricated systems (material dependent)- eexcellent temperature resistance (depending on selected '0'ring


material)- ccompact design (for small installation height)- ccompact, stable square energizer ring profile (less deformation on

pulsating load)- ffast pressurisation, no “blow-bby” effect (due to implemented


(depending on diameter and quantity)- aavailable as individual single piece or limited-llot production- aavailable in large quantities - aavailable for all diameters up to 1.500 mm

F-SLIDE K08-DS seal is a "heavy duty" double acting piston seal consisting of a PTFE compound sealing element and an elastome-ric square profile energizer element. Interference fit and preload of energizing element ensures a good initial sealing effect.Designed with a square energizer profile ring for increased stability and reduced deformation of the energizer ring under pulsatingload. By selecting a suitable energizer material, the seal can be "adjusted" to suit various chemical and thermal conditions (seematerial combinations for F-SLIDE seal on page 35).

55 ECONOMOS®

ard dimensionsHousing recommendation

Table of recommended K08-DDS standard dimensions

• For pressure range above 600 (800) bar we can offer special designs with integrated back-up rings (see page 59, special tailormade designs). Please contact our technical department.


F-Slide K08-DS, standard application, actual bore diameter: ØD=210 mm, predetermined or chosen housing dimensions (from list "K08-DS available standard dimensions”) --> Ød=185 mm, L=12,5 mmrequired material: ECOFLON 3 / FKM85 --> article number: 4FPH0210 (from list "K08-DS available standard dimensions”, article-no.-row 4 for material combination ECOFLON 3/FKM85)


F-Slide K08-DS, standard application, bore diameter ØD=209,55 mm (8 1/4”)housing diameter Ød=ØD - 25 = 184,55 mm and housing height L= 12,5 mm (from table “recommended K08-DS standard dimen-sions for diameter range ØD 200 - 299,9 mm), required material: ECOFLON 2 / NBR85 --> article number: not available, housingdimension D x d x L followed by material combination should be used for designation:

Required designation for placing an order: F-SLIDE K08-DS 209,55 x 184,55 x 12,5mm FLON 2 / NBR85Seal type housing dimensions material combination



SLIDE

D - 10D - 15D - 20D - 25D - 30D - 35D - 40

20 - 49,950 - 59,9

60 - 199,9200 - 299,9300 - 529,9530 - 679,9680 - 1500

5,07,5

10,012,515,017,520,0

0,30,40,40,40,81,21,2

4,05,06,08,5

10,013,015,0

BoreØ D

GrooveØ d

Height L

Radiusr

Lead-inc


0,400,500,600,600,700,801,00

0,300,300,400,400,500,600,70

0,200,200,250,250,300,500,60

0,100,100,150,150,200,200,30

F-SSLIDE seals K08-DDS basic information

+0,2





F-SLIDE K08-DS 4FPH0210Seal type article no.

F-S

56 ECONOMOS®

10,015,020,022,025,030,035,035,040,040,043,050,060,080,095,0

105,0120,0130,0160,0175,0185,0195,0205,0215,0220,0225,0235,0245,0250,0255,0

255,0265,0270,0275,0280,0290,0300,0310,0320,0330,0340,0350,0360,0370,0380,0390,0400,0420,0450,0460,0470,0490,0495,0515,0

20,025,030,032,035,040,045,050,055,060,063,070,080,0

100,0115,0125,0140,0150,0180,0200,0210,0220,0230,0240,0245,0250,0260,0270,0275,0280,0

285,0290,0300,0305,0310,0320,0330,0340,0350,0360,0370,0380,0390,0400,0410,0420,0430,0450,0480,0490,0500,0520,0530,0550,0

5,05,055555

7,57,510101010101010101010

12,512,512,512,512,512,512,512,512,512,512,5

12,512,51515151515151515151515151515151515151515

17,517,5

1FPH00101FPH00201FPH00301FPH00401FPH00501FPH00601FPH00701FPH00801FPH00901FPH01001FPH01101FPH01201FPH01301FPH01401FPH01501FPH01601FPH01701FPH01801FPH01901FPH02001FPH02101FPH02201FPH02301FPH02401FPH02501FPH02601FPH02701FPH02801FPH02901FPH0300

1FPH03101FPH03201FPH03301FPH03401FPH03501FPH03601FPH03701FPH03801FPH03901FPH04001FPH04101FPH04201FPH04301FPH04401FPH04501FPH04601FPH04701FPH04801FPH04901FPH05001FPH05101FPH05201FPH05301FPH0540







BoreØ D

GrooveØ d

Height L






F-SLIDE seals K08-DS available standard dimensions / article numbers

SLIDE525,0535,0545,0555,0565,0575,0585,0595,0605,0615,0625,0635,0640,0650,0670,0680,0690,0700,0710,0720,0730,0740,0760,0780,0

790,0800,0810,0840,0860,0880,0900,0910,0925,0940,0960,0

1.010,001.060,001.080,001.100,001.140,001.260,001.360,001.410,001.460,00

560,0570,0580,0590,0600,0610,0620,0630,0640,0650,0660,0670,0680,0690,0710,0720,0730,0740,0750,0760,0770,0780,0800,0820,0

830,0840,0850,0880,0900,0920,0940,0950,0965,0980,0

1.000,01.050,001.100,001.120,001.140,001.180,001.300,001.400,001.450,001.500,00

17,517,517,517,517,517,517,517,517,517,517,517,5202020202020202020202020

2020202020202020202020202020202020202020


1FPH07901FPH08001FPH08101FPH08201FPH08301FPH08401FPH08501FPH08601FPH08701FPH08801FPH08901FPH09001FPH09101FPH09201FPH09301FPH09401FPH09501FPH09601FPH09701FPH0980







BoreØ D

GrooveØ d

Height L





F-SLIDE seals K08-DS available standard dimensions / article numbers


57 ECONOMOS®

Special solutispe

Tailormade X(F)-SSLIDE seal range

When choosing a seal company to do business with, several issues need to be con-sidered: quality, speed, reliability of delivery, and the overall performance of the sea-ling product. Clearly, not only does ECONOMOS® have strengths in these areas, butit can also enhance your satisfaction, because apart from delivering 'standard' sealsand components - backed up by first class application advice - it can also designsolutions that are tailor-made to your particular application, thus maximising the per-formance of your product.Below are some examples of additional ranges and tailor-made solutions.

Tailormade X-SLIDE and F-SLIDE solutions

Additional standard rod seal range

Additional standard piston seal rangeK08-EE K08-EES K08-PP

S09-DD S09-DDS

Standard singleacting pistonseal

Standard heavyduty singleacting pistonseal

Standard heavyduty doubleacting rod seal

Standardpolyurethanedouble actingpiston seal

Standarddouble actingrod seal

tailormadeionsecials

Tailormade sealing solutions (digest)

Tailormade piston seal solutions

Tailormade rod seal solutions

Special Special Special

Special Special Special

integrated backup-ring for higherpressure / largergaps

integratedelastomericseal for bettersealing effect/ media sepa-ration

integrated “lipseal section”for increasedflexibility /faster pressuri-sation

integratedback up-ringfor higherpressure / lar-ger gaps

integrated “lipseal section”for increasedflexibility /faster pressuri-sation

integratedelastomerseal for bettersealing effect/ media sepa-ration

59

CompanyAddressZIP Code City DatePhone FaxContact person Dpmt.

Description of applicationOperating conditions:

linear spiral static

rotating oscillating

single acting double acting

Current seal type

Material

Manufacturer

Manufacturers seal code

Problem with actual sealDelivery Mounting

Material Leakage

Lifetime Wear

Measurements

Customer Service

I want to use:X-SLIDE seals (Polyurethane)excellent sealing and mounting properties

F-SLIDE seals (PTFE)excellent chemical and temp. resistance

Please indicate most suitable profile

I selected following seal profile:

Please offer wiper / guide ring / lip seal as well!

Required Service Housing and seal recommendation

Offer for pcs. / estim. yearly demand

Others

Min. Nominal Max.TempPressureStrokeSpeedGap ”s”Media:Sliding surface material:Surface hardness:Surface roughness:

Additional comments:

Please send this enquiry to your nearest ECONOMOS subsidiary. You will find the respective addresses at the back covers flap.

S09-E S09-ES S09-D S09-DS Special Special

enquiry sheet for rod sealsRODwww.economos.com

CompanyAddressZIP Code City DatePhone FaxContact person Dpmt.

Description of applicationOperating conditions:

linear spiral static

rotating oscillating

single acting double acting

Current seal type

Material

Manufacturer

Manufacturers seal code

Problem with actual sealDelivery Mounting

Material Leakage

Lifetime Wear

Measurements

Customer Service

I want to use:X-SLIDE seals (Polyurethane)excellent sealing and mounting properties

F-SLIDE seals (PTFE)excellent chemical and temp. resistance

Please indicate most suitable profile

I selected following seal profile:

Required Service Housing and seal recommendation

Offer for pcs. / estim. yearly demand

Others

Min. Nominal Max.TempPressureStrokeSpeedGap ”s”Media:Sliding surface material:Surface hardness:Surface roughness:

Additional comments:

Please send this enquiry to your nearest ECONOMOS subsidiary. You will find the respective addresses at the back covers flap.

K08-D K08-DS K08-E K08-ES Special Special

www.economos.com enquiry sheet for piston sealsPISTON

Total seal ranSea

62 ECONOMOS®

ECONOMOS® total standard profile seal range

For all non standard profiles and our free seal design and advisory services, please contact your local ECONOMOS® offi-ce.

Wipers

Rod seals

Piston seals

Rotary seals

Guide- and Back-up rings

O-Rings (static seals)

ngeal ran

Trade marks

63 ECONOMOS®

Trade marks [TM], liability exclusion

Trade Marks [™]

Photos

Liability exclusion

Other ECONOMOS®

Products and Services

ECONOMOS®´ branding program integrates our own products under a unified set oftrade names all over the world. This provides a clear and consistent identification ofall our materials and makes them available through all manufacturing partners world-wide. All other trade names noted in this brochure are the property of their respec-tive owners.

The rights of all photos used in this brochure which are not of ECONOMOS® origin areheld by the respective owners.

All information supplied by or on behalf of ECONOMOS® [plastic products and sealsin relation to its products], whether in the nature of data, recommendations or testresults are supported by research and correspond to the state of the art. The buyerundertakes the responsibility to check the information provided in this catalogue forhis specific application. ECONOMOS® does not undertake any liability in the individu-al case because of the diversity of possible variations in the practical application inrespect of the particularity of applications, further processing or the otherwise use ofthe components. Technical amendments are reserved. The buyer is obliged to checkwhether the products correspond to the supplied data, recommendations and testresults, undertakes the full liability in respect of the application, use and further pro-cessing of the products as well as the use of the information. No liability whatsoever shall attach to the products produced by ECONOMOS® [pla-stic products and seals] for any infringement of the rights owned or controlled by athird independent party which may be caused by the use or a further processing ofthe components by the buyer.

Besides the products detailed in the catalogue, ECONOMOS® is a world class sup-plier and manufacturer of machined plastic and elastomeric components. Our mate-rials and production expertise enables us to manufacture components from simple tocomplex in any volume. As engineers, we can provide a complete technical advisoryservice. For further information please request our comprehensive 32 page AEPP bro-chure.

Our aim is provide a complete service to our customers. ECONOMOS® can offer manyother products and services (depending on the country). Please refer to our groupweb Site: www.economos.com and choose from 'select country' for further details onyour local ECONOMOS® web site. Alternately, contact your nearest ECONOMOS® offi-ce - details on inside rear flap of this catalogue.

SubsECONOMOS® Subsidiaries worldwideAUSTRIAEconomos Dichtungstechnik GmbH.Madstein am Ort 9A-8770 St. MichaelPhone: +43 3843 51150Fax: +43 3843 51155E-mail: [email protected]: http://www.economos.at

AUSTRALIAEconomos Australia Pty. Ltd.2/107 Beaconsfield StreetSilverwater NSW 2128Phone: +61 2 9748 7466Fax: +61 2 9748 7006E-mail: [email protected]: http://www.economos.com

ARGENTINASeal Jet Economos S.A.Tucumán 4140(3000) Santa Fe, ArgentinaPhone: +54 342 455 3644Fax: +54 342 453 0299E-mail: [email protected]: http://www.economos.com

BELGIUMEconomos Belgium N.V. Industriezone 5 Mollem 36B-1730 AssePhone: +32 24 523600Fax: +32 24 523518E-mail: [email protected]: http://www.economos.be

CANADAEconomos Canada Inc.5777 Coopers AvenueMississauga, Ontario L4Z 1R9Phone: +1 905 712 1600Fax: +1 905 712 1606E-mail: [email protected]: http://www.economos.ca

CHINAEconomos (Qingdao) Seal Tech Co. LtdSouthern side of Zhuzhou Road,266101Qingdao, ChinaPhone: +86 532 88702609 / 88701660Fax: +86 532 88702325E-mail: [email protected]: http://www.economos.cn

CZECH REPUBLICEconomos Riha CZ, s.r.o.Cernokostelecká 128/161102 00 Praha 10Phone: +420 267 900 711Fax: +420 267 900 741E-mail: [email protected]: http://www.economos.cz

FRANCEEconomos France S.A.Parc d´activités des Arpents24 rue du Pré des AulnesF-77341 Pontault CombaultPhone: +33 1 60 348502Fax: +33 1 60 348537E-mail: [email protected]: http://www.economos.fr

GERMANYEconomos Deutschland GmbH.Robert-Bosch-Strasse 11D-74321 Bietigheim-BissingenPhone: +49 7142 5930Fax: +49 7142 593110E-mail: [email protected]: http://www.economos.de

ITALYEconomos Italia S.r.lVia E. Fermi 42I-37136 VeronaPhone:+39 045 8622406Fax: +39 045 8648623E-mail: [email protected]: http://www.economos.it

INDIAEconomos India Private Ltd.16, Phase IV, Okhla Industrial Estate New Delhi 110020, IndiaPhone.: +91 11 55640248Fax: +91 11 26932612E-mail: [email protected]: http://www.economos.com

JAPANEconomos Japan K.K.MT No. 2 Build. 4-19-2, Shimomaruko, Ohta-kuTokyo 146-0092, JapanPhone: +81 3 5732 3301Fax: +81 3 5732 3303E-mail: [email protected]: http://www.economos.jp

MALAYSIAEconomos Malaysia Sdn. Bhd.No 12, Jalan PJS 7/21,Bandar Sunway, Petaling Jaya, 46150 Selangor Darul Ehsan, MalaysiaPhone: +603 56382848Fax: +603 56312248E-mail: [email protected]: http://www.economos.com

NETHERLANDSEconomos Interplastics NL B.V.Twekkeler-es 287547 SM EnschedePhone: +31 53 432962Fax: +31 53 4325617E-mail: [email protected]: http://www.economos.com

PHILIPPINESEconomos Philippines Co. Ltd.# 107 Epifanio Delos Santos Avenue (EDSA)1550 Mandaluyong City, PhilippinesPhone: +63 2 717 1724Fax: +63 2 717 1725E-mail: [email protected]: http://www.economos.ph

POLANDEconomos Polska Sp.z.o.o.Ul. Zimowa 41PL-40-318 Katowice, PolskaPhone: +48 32 352 7800Fax: +48 32 352 7801E-mail: polska@econo mos.comInternet: http://www.economos.pl

SLOVENIAEconomos d.o.o. Ptujska c. 3432000 MariborPhone: +386 2 629 52 76Fax: +386 2 629 52 77E-mail: [email protected]: http://www.economos.com

SPAINEconomos España, S.L.Polig Ind. Cova Solera, c/Paris, 1 – 7, Bajos AE-08191 Rubi (Barcelona)Phone: +34 93 5873510Fax: +34 93 5873511E-mail: [email protected]: http://www.economos.es

SWEDENEconomos Sverige ABHammarby fabriksväg 29 - 31120 33 Stockholm, SwedenPhone: +46 84 620180Fax: +46 84 620140E-mail: [email protected]: http://www.economos.se

SWITZERLANDEconomos Schweiz GmbHHungerbüelstrasse 17CH-8500 FrauenfeldPhone: +41 52 7212021Fax: +41 52 7215521E-mail: [email protected]: http://www.economos.ch

THAILANDEconosto (Thailand) Limited99/28-31 Soi Wat Ladprao, Ladprao Road, LadpraoBangkok 10230, ThailandPhone: +66 (0)2 9316868 / 79Fax: +66 (0) 2 9316880 / 1E-mail: [email protected] Internet: http://www.econostothai.com

UKRAINEEconomos-Ukraine Ul. O. Teligi, 15A04112 Kiev , UkrainePhone: +380 444401181Fax: +380 444407556E-mail: [email protected]: http://www.economos.com.ua

UNITED KINGDOMEconomos UK Ltd.83 Buckingham AvenueSlough, BerkshireSL1 4PNPhone: +44 1753 696565Fax: +44 1753 696192E-mail: [email protected]: http://www.economos.co.uk

USAEconomos USA Inc.26820 Fargo AvenueCleveland, OH 44146Phone: +1 216 3782600Fax: +1 216 3782606E-mail: [email protected]: http://www.economosusa.com

HEADQUARTERSEconomos Austria GmbH.Gabelhoferstr. 25A-8750 JudenburgPhone: +43 3572 82555Fax: +43 3572 82555-58E-mail: [email protected]: http://www.economos.com

Sales Eastern Europe & Ex-SUEconomos Austria GmbH.Iz NÖ Süd, Str. 1, Obj. 50A-2351 Wr. NeudorfPhone: +43 2236 62207Fax: +43 2236 62207-7E-mail: [email protected]: http://www.economos.com

Owner, editor and publisher:Economos Austria Gesellschaft m.b.H.HeadquartersGabelhoferstraße 25A-8750 Judenburgphone: +43 3572 82 555 0fax: +43 3572 42520Email: [email protected]: www.economos.com

Design: G. Sterba, Marketing Dpmt.H. Rehschützecker, Application Engineering

Photos: G. Sterba

09/2005

Art.Nr.: 18270

Modification & misprints reserved

Documents

X-SLIDE