WITH LEVEL-RIGHT®

AND LEVEL-RIGHT®

MAXX YOU’RE COVERED THROUGH…

THICK THINand

FROM THIN TOPPING TO DEEP FILL, FLOOR

CHALLENGES COME IN ALL DEPTHS AND SIZES

LEVEL-RIGHT PRODUCTS FOR BOTH THICK AND THIN JOBS

COVER ANY FLOOR CHALLENGE

Count on the Level-Right family to turn even the toughest floor

challenges into smooth, level floors — just 2–4 hours after pouring!

THICK OR THIN. From deep fill to capping concrete, Level-Right

Self Leveling Underlayment is versatile enough to meet the demands

of virtually any floor challenge. Level-Right installs from 0"–3" and

can be poured over concrete, old floor goods, adhesive residue and

wood subfloors — often without shotblasting or scarifying.

IN A HURRY. Level-Right Maxx lets you cover a lot of floor in

amazingly little time. It installs at a thickness of 1/8"–11⁄4" in just one,

easy pour. Level-Right Maxx is self-drying, allowing most floor goods

to be installed within 24–48 hours after installation. For specialized

projects, Level-Right Maxx is moisture tolerant, enabling it to be

installed during the early stages of construction.

Level-Right and Level-Right Maxx can level entire floors, new or old

and attain compressive strengths up to 5,500 psi (37.9 MPa). They

work on, above or below grade, with no troweling required. Best

of all, their fast set times enable light trade work to resume quickly.

Whatever the floor challenge, Level-Right Self-Leveling Underlayments

are dynamic enough to meet the challenge.

FEATURES/BENEFITS• New construction or renovation• Levels entire floors or transition areas,

featheredge to deepfill• Resurfaces old or damaged concrete

floors• Caps cracked, lightweight concrete

• Above, on or below grade• Fills “duck ponds” in concrete floors• No troweling required• Can walk on in as little as two to four

hours after application• Experienced, authorized, licensed

applicators throughout North America

• Exceeds standards set by leading floor goods manufacturers

• Can be used in any continuous pumping machine

• Supported by Maxxon® Corporation

CHOOSING THE RIGHT SELF-LEVELING UNDERLAYMENT/OVERLAYMENTLevel-Right® Level-Right® Maxx

Installation Depths 0–3" (76 mm) 1/8"–11⁄4" (3–32 mm)

Compressive Strength Up to 5,500 psi (37.9 MPa) Up to 5,500 psi (37.9 MPa)

Installation over Existing Floor Goods Shotblasting is often not required Shotblasting required

Wear Surface with Maxxon-approved Sealer No Yes

Polymer Modified No Yes

Evaluation Reports Legacy Report ESR-2540, UL ER 8477-01 —

GREENGUARD Gold CertifiedSM Yes —

Recycled Content Yes —

TECHNICAL DATA

TECHNICAL DATA

FEATURES/BENEFITS

FEATURES/BENEFITS

• Water resistant• Pours over concrete, old floor goods and adhesives• Ideal for large projects or small repair jobs• 0"–3" installation depth

• High strength• No special prepping, removal of old floor goods,

or hand finishing required• Can be feather-edged

• Listed in more than 100 UL Fire Rated Designs• GREENGUARD Gold Certified

• Moisture tolerant• High strength• Self drying• Many floor coverings can be installed 24–48 hours

after application

• 1/8"–11⁄4" installation depth• Compatible with a variety of floor coverings, tile and stone

mortars, floor adhesives, epoxy and polyurethane adhesives.• Can be used as a wear surface when sealed with a

Maxxon-approved sealer.

LEED Certification ............May help contribute toward earning points, see www.MaxxonCorporation.com

Flexural Strength ...................... 1,260 psi (8.7 MPa) 28 daysASTM C348

Flexural Strength .................................. 1,160 psi (8.0 MPa)ASTM C348

Tensile Strength ........................................ 306 psi (2.1 MPa)ASTM C190

Dry Density .........................approx. 125 lbs/ft3 (2,002 kg/m3)

Dry Density ........................approx. 125 lbs/ft3 (2,002 kg/m3)

VOC Emissions .......................... GREENGUARD Gold CertifiedFire and Sound Code Listings .............. See page 4UL Fire Designs ..................................... See page 4

Tensile Strength ............................ 720 psi (5.0 MPa) 28 daysASTM C190

Compressive Strength ....Typical: 3,000 psi (20.7 MPa) 3 daysModified ASTM C109 4,500 psi (31.0 MPa) 7 days 5,500 psi (37.9 MPa) 28 days

Compressive Strength ....Typical: 1,750 psi (12.1 MPa) 1 dayModified ASTM C109M 3,500 psi (24.1 MPa) 7 days 5,500 psi (37.9 MPa) 28 days

Fuel Contribution ................................................0Smoke Density ...................................................0Flame Spread ....................................................0

Fire Performance ASTM E-84

PRO

JEC

T SP

OTL

IGH

T

PROJECT SPOTLIGHT NORTHROP AUDITORIUM UNIVERSITY OF MNMINNEAPOLIS, MN Contractor: JE Dunn Construction

Architect: HGA Architects

Scope: 8,100 sq. ft. of Level-Right at a depth of 1/2".

PRO

JEC

T SP

OTL

IGH

T

PROJECT SPOTLIGHT YUENGLING FACTORY POTTSVILLE, PA

Contractor: Hiem Construction

Scope: 2,800 sq. ft.of Level-Right Maxx poured in two lifts at a total average depth of 11⁄2".

Working Time ................................ Approx. 30 mins

Open to Foot Traffic .......................... Approx. 4 hrsAble to Accept Tile and Stone ............... 12–16 hrsAble to Accept Impervious Floor Coverings ...................................... 24–48 hrs

INSTALLATIONLevel-Right®, Level-Right® Maxx Concrete subfloors must be fully cured, moisture free and have no efflorescence. The substrate surface shall be clean, dust and contaminant free. Cracks should be filled with a crack filler or an elastomeric compound. Plumbing or electrical penetrations should be properly fire stopped and sealed. The surface of Level-Right products must always be protected from oil, salt, water and surface wear.For epoxy or seamless flooring installations over Level-Right products, the manufacturer and installer of the flooring will be responsible for compatibility, bond test patches, installation recommendations and warranty. Because Maxxon Corporation does not perform the actual Level-Right installation, they cannot be held responsible for the results of epoxy or seamless flooring over Level-Right products.

TESTING For Level-Right products, field testing must be performed in accordance with modified ASTM C109. Before independent sampling, contact the Maxxon Quality Control department to ensure that proper procedures are followed.

LIMITATIONS 1. Do not pour Level-Right products where the floor temperature is less than 50 °F (10 °C) or greater than 100 °F (37.7 °C).2. Protect the poured mortar from wind and sun, and from freezing temperatures for the first 72 hours.3. The structural floor should be adequate to withstand design loads, including construction loads, with deflection limitations of L/360. The structural subfloor and floor joist must both comply with manufacturers’ maximum span criteria. Typically a deflection limitation of L/360 is adequate for Maxxon Underlayments. Some floor coverings may require a stiffer floor system. Maxxon Underlayments are non-structural and therefore cannot be expected to reinforce structurally deficient subfloors. Necessary allowances should be made for expected live, concentrated, impact, and/or dead loads including the weight of finished floor goods and setting beds.4. Additional consideration should be taken for concentrated/dynamic loads. U.S. building codes typically specify a uniform live load of 40 pounds per square foot for residential floor designs. This load is intended to account for large loads that can occur in a building. In reality these loads are not uniform, but rather consist of items such as furniture and appliances that actually induce concentrated

loads far exceeding 40 lbs per sq ft. Rolling concentrated loads such as office chairs, wheelchairs, and motorized scooters add turning, twisting, repetition, and other dynamics which should also be taken into consideration. Determining the appropriate structural design of the floor is not the responsibility of Maxxon nor the Maxxon applicator.5. Level-Right products are non-structural underlayments, for interior use only. Level-Right is not intended for use as a wear surface.6. Level-Right Maxx may only be used as a wear surface when sealed with a Maxxon approved sealer.7. Level-Right products will not structurally bridge over expansion joints, saw cuts or structural cracks, which should be allowed to continue through the Level-Right or Level Right Maxx. The architect or structural engineer must specify expansion joints and show their location in areas that will receive hard surface floor goods such as ceramic or marble tile, and hardwood flooring.8. For Level-Right, maximum installation thickness is 3" (76 mm). For Level-Right Maxx, maximum installation thickness is 11⁄4" (32 mm). Call Maxxon Corporation for application details.9. For applications other than those over structural concrete call Maxxon Corporation for the Application Bulletin.10. Maxxon Underlayments are not a vapor barrier. The general contractor/project superintendent, architect, specifier, or building owner shall test below grade, on grade, or elevated slabs for MVER (ASTM F1869-16) or RH (ASTM F2170). If the MVER or RH of the concrete substrate exceeds the floor covering manufacturer’s respective requirements for the finished flooring system, the concrete should be treated with a moisture vapor barrier, such as Maxxon DPM or Maxxon MVP, before installing a Maxxon Underlayment.11. Level-Right products are not resurfacing toppings for heavy-duty industrial floors or chemical environments requiring customized industrial toppings. Excessive service conditions, such as steel or hard-plastic wheeled traffic, dragging heavy metal equipment or loaded pallets with protruding nails over the floor can cause gouging and indentation.

For customized CSI specs for all Level-Right and Level-Right Maxx applications, see www.MaxxonCorporation.com.

Another superior product from: Maxxon® Corporation • 920 Hamel Road • P.O. Box 253 Hamel, MN 55340 USA • 763-478-9600 • Fax: 763-478-2431

FIRE RATINGSUL Design

ULC Design

G230G516G524G551G553G560G561G563G566G574J917J919J920J924J927J931J957J958J991J994L006L201L202L206

L208L209L210L211L212L501L502L503L504L505L506L507L508L509L510L511L512L513L514L515L516L517L518L519

L520L522L523L524L525L526L527L528L529L530L532L533L534L535L536L537L538L539L540L541L542L543L545L546

L547L549L551L552L556L557L558L560L562L563L564L565L567L569L570L573L574L576L577L579L581L583L585L588

L589L590L592L593M500M502M503M504M505M506M508M510M511 M513M514M515M517M518M519M530M531M533M534M536

I530L003L201

L511L512M500

M501M503M514

M520M521

LEED® INFORMATIONFor information regarding how

Level-Right may contribute toward points for LEED project contribution, contact

your Regional Representative at (800) 356-7887 or visit

www.maxxon.com/go_green.

FIRE/SOUND RATINGSEvaluation Reports - Meeting fire and sound code together

Accepted by local building officials for fire and sound code compliance, Evaluation Reports are technical reports which verify that specific products meet the following code requirements and warrant regulatory approval. Minimum code requirements: Sound - 50 STC/IIC, Fire - I Hour

International Code CouncilICC ESR #2540 For the following assembly types:

Additional ICC ES Reports: ESR #1141, ESR #1153, ESR #1774

Underwriters Laboratory InternationalUL ER #8477-01 For the following assembly types:

• Parallel Chord Truss• 2x10 Wood Truss

• I-Joist• Hambro

• Steel Joist• Precast Concrete

• Parallel Chord Truss• 2x10 Wood Truss

• I-Joist• Steel Joist

• Precast Concrete

For more info: 800-356-7887 • Email: info@level-right.com www.MaxxonCorporation.com

©2004–2017 Maxxon Corporation. All Rights Reserved. Level-Right, Level-Right Maxx and associated logos are registered trademarks of Maxxon Corporation, Hamel, MN, USA. Printed in the USA. #60039, 5-17

Underwriters Laboratories Inc.® Listed

INST

ALL

ATIO

N

DET

AILS Gypsum

Wallboard

Steel or Wood Stud and PlateLevel-Right® orLevel-Right Maxx

Level-Right® or Level-Right Maxx

Sealed Joint

Precast or Poured Concrete

Gypsum Wallboard

Steel or Wood Stud and Plate

Carpet, Tile or Other Floor Goods

Existing Uneven Concrete

Gypsum Wallboard

Steel or Wood Stud and PlateLevel-Right® orLevel-Right Maxx

Level-Right® or Level-Right Maxx

Sealed Joint

Precast or Poured Concrete

Gypsum Wallboard

Steel or Wood Stud and Plate

Carpet, Tile or Other Floor Goods

Existing Uneven Concrete