Wireless’HandheldLinear’Imager’Barcode’Scanner’ User’s Manual User Man… · 2D imager hand held barcode scanner. This is a cutting-edge gun-type area imaging barcode

EC BT-8500 Wireless Handheld Linear Imager Barcode Scanner

User’s Manual

www.ecline.com.mx

Table of Contents 1. Introduction ............................................................................. 1

1.1 Safety & Caution.................................................1 1.2 FCC Warning ......................................................2

2. General Description ................................................................... 3 2.1 Product Description ............................................3 2.2 Illustration ...........................................................3

3. Installation ............................................................................... 4 3.1 Unpacking .........................................................4 3.2 Mounting............................................................4

4. Setup Bluetooth Communication ............................................. 7 4.1 Pairing ..............................................................7 4.2 Setup SPP Master Mode ..................................7 4.3 Setup SPP Slave Mode ....................................8 4.4 Setup HID Slave Mode .....................................8 4.5 Sleep Mode ......................................................9 4.6 Batch Mode ......................................................9 4.7 Out of Range ....................................................9 4.8 Scanner Mode ................................................10

5. Configuring............................................................................ 11 5.1 Preface ...........................................................11 5.2 Changing Scanner Settings with

Programming Codes.........................................11 5.3 Programming Flow Chart................................12

6. Programming Menu .............................................................. 13 6.1 General Process ...............................................13 6.2 Set Cradle Interface..........................................14 6.3 RS232 mode parameters..................................18 6.4 Keyboard Wedge Mode Parameters ................21 6.5 Output Characters ............................................24 6.6 Code Type ........................................................25 6.7 UPC/EAN/JAN Parameters ..............................28 6.8 Code 39 Parameters.........................................30 6.9 Code 128 Parameters.......................................32 6.10 Interleaved 2 of 5 Parameters ..........................34 6.11 Industrial 2 of 5 Parameters..............................37 6.12 Matrix 2 of 5 Parameters ..................................38 6.13 CODABAR Parameters ....................................41 6.14 Code 93 Parameters.........................................43 6.15 Code 11 Parameters.........................................45 6.16 MSI/plessey Code Parameters .........................47 6.17 Telepen Parameters .........................................49 6.18 GS1 Databar Parameters .................................51 6.19 GS1 Databar Limited Parameters.....................52 6.20 GS1 Databar Expanded Parameters ................53

7. Miscellaneous Parameters.................................................... 54 7.1 Bar Code ID ........................................................54 7.2 preambles and postambles Insertion................56 7.3 Character deletion ............................................60 7.4 Appendices .......................................................65 A. Decimal Value Table ............................................65 B ASCII Table.........................................................66

C Function Key Table.............................................71 D. Decimal Value Table..........................................72 E. Technical Specifications ....................................73 F. Indicator LED Status ..........................................74 G. Electrical Characteristics ...................................75 H. Scan Map .............................................................76 A. How to communicate with Bluetooth

dongle 77

1

1. Introduction

Thank you for purchasing this brand-new designed 2D imager hand held barcode scanner. This is a cutting-edge gun-type area imaging barcode scanner which is designed specifically for retailer, entertainment coupons, medical environment, shipping industry and etc. That adds on more user friendly functions and has replaceable cable that makes it more easily to be operated by the customers. This high performance gun-type scanner provides the customer with the most cost effective solution in the market. It is perfectly suitable and definitely the best choice for you.

1.1 Safety & Caution

1) Please read the following safety statement carefully.

2) Please preserve this user manual for reference sometime.

3) Before cleaning the device, the users must cut off all AC power. Do not use liquid or spray type of detersive to clean the device. Please use dampish cotton cloth to clean the device.

4) The outlet must set nearby the device for connecting power easily.

5) Keep the device dry to avoid short circuit. 6) During installation you must fix the equipment at

solid table to avoid damage caused by falling. 7) Before inserting power please ensure the voltage

is healthy to the equipment. 8) For safety please tie wire well and don’t put

anything on the wire. 9) If you don’t use this equipment for long time,

please cut off the power to avoid damage from surge power.

10) Don’t spray any liquid on this scanner because it may cause a fire or short circuit.

2

11) Please do not disassemble the equipment. For safety only the qualified serviceman can disassemble the equipment.

12) If there are the following situations please contact with the qualified serviceman to check this equipment. (a) The damage of wire or pin of power supply. (b) Some Liquid infiltrate into the equipment. (c) The equipment has been exposed to wet

environment. (d) The equipment can’t work well. (e) The equipment has any obvious damage,

making the device working abnormally. 13) Don’t storage the device at the temperature lower

than -20°C (-4°F) or higher than +70°C (158°F) to avoid any damage.

1.2 FCC Warning This equipment complies with the requirements in Part 15 of FCC. Any operation must comply with the conditions below:

1) The equipment will not cause any severe interference.

2) The equipment can avoid any interference from environment.

Statement: This product is classified as B class product. In environment this product may cause some interference. In this situation the user may do something to avoid interference.

3

2. General Description

2.1 Product Description BT-8500 is a high performance wireless linear imager barcode scanner supporting linear and area imager barcode scanning. This device is very easy to configure by this manual, you can set up by scanning all necessary programming codes one time that meet applications, the settings are directly saved permanently, and all settings can be disabled after scan reset factory default.

2.2 Illustration BT-8500 Series

4

3. Installation

3.1 Unpacking 1) Take the device and accessories out of the box. 2) Remove the packing material. 3) Check the standard shipment packing list to

make sure you have received all of the items ordered.

Wireless Linear Imager Scanner Bluetooth Cradle or Charger (optional) Power Adaptor (if applied) Communication Cable Skip resistant pad Iron panel of cradle and screw Product Compact Disc 4) Visually inspect the device and accessories for

any evidence of physical damage. 5) If anything is missing or appears to be damaged,

immediately contact your dealer.

ATTENTION: Store the packing material and boxes: It should be used whenever the device is transported for servicing.

3.2 Mounting Once you have unpacked all components, you can start installing the device as below steps: BT-8500 Scanner 1) The Scanner must be charged for a minimum of

8 hours before the scanner can be placed in full operation for the first time.

2) The cradle will indicate in red light when the scanner is being charged.

3) Once the battery is fully charged, the green LED of scanner will be on. The green light will be off when the scanner leaving from cradle. When the battery is over charged, the red and green LED will be flashing.

4) If the battery power capacity is too low, the

5

scanner will indicate with red LED and beeper warning.

BT-8500 Cradle 1) Connect the supplied communication cable at

the bottom side of the scanner and you will hear a “click” when the connection is made.

2) Turn off the host system. 3) Connect the other side of the communication

cable to the right connector of your host system.

4) Plug the external power supply into the power jack on the bottom of the cradle.

5) Plug the power supply into the AC outlet. 6) Turn on your host system. 7) To setup Bluetooth communication between

the scanner and cradle. (see chapter 4)

6

Cable Installation

Connect cable and adaptor to Cradle. The other end of cable will be connected with host device. Lock the iron panel of Cradle by screwdriver.

Skip resistant pad position

7

4. Setup Bluetooth Communication

Before the operation, Bluetooth communication must be setup between the scanner and cradle.

4.1 Pairing Each scanner has to be linked or paired to a cradle by scanning the unique Bluetooth MAC address code located on the bottom of cradle. The pairing between scanner and cradle is one to one that is one scanner can be paired to a cradle only.

4.2 Setup SPP Master Mode Please follow the steps to setup the communication between the scanner and cradle. 1) The scanner must scan “SPP Master Mode”

barcode to set the scanner in master mode. 2) Scan the Bluetooth MAC address code located

on the bottom of the cradle.

3) When the Bluetooth MAC address code was

successfully scanned, scanner will sound 3 beeps with Green led.

4) Wait approximately five seconds for completing the connection process with up-tone.

5) If successful, blue LED of scanner will slow flash and the cradle will be continued on.

8

ATTENTION: It is important to know that the scanner will only communicate with the cradle with the unique Bluetooth MAC address. Other scanner cannot pair with that cradle until the original connection is broken. If the cradle pairs with another scanner, the cradle will disconnect with the first scanner and then re-connect with another scanner.

4.3 Setup SPP Slave Mode

Please follow the below steps to setup the communication between the scanner and Bluetooth application device. 1) The BT-8500 scanner must scan “SPP Slave

Mode” barcode, to set the BT-8500 scanner in slave mode.

2) When control the Bluetooth device to search the scanner, enter pin code (default 00:00:00) to setup comport.

3) When BT-8500 scanner is successful connected, the scanner blue LED will also blink with up-tone. Blue LED will slowly flash to finish the setup.

4.4 Setup HID Slave Mode

To setup the communication between the BT-8500 scanner and Bluetooth HID profile application device, follow the steps. 1) The BT-8500 scanner must scan “HID Slave

Mode” barcode to set the BT-8500 scanner in HID slave mode.

2) When control the Bluetooth device to search the scanner, enter pin code to setup pairing. You can scan number barcode on Appendix A, “Decimal Value Table” number 0~9, to setup.

3) When BT-8500 scanner is successful connected, scanner blue LED will also blink with up-tone. Blue LED will slowly flash to finish the setup.

9

4.5 Sleep Mode

The BT-8500 scanner enters sleep mode to save battery energy, when the BT-8500 scanner is used for 1 minute or 10 minutes. During sleep mode all the functions and connection will be halted. After press the trigger button the scanner will wake up and reconnect the communication with the cradle or Bluetooth device.

4.6 Batch Mode This batch mode is enabled when you have scanned “Batch Mode On”. The scanned data is stored in the memory of the BT-8500 instead of being transmitted. You can delete the last scanned barcode data by scanning “Delete Last Data” barcode. This function is disabled when you scan “Batch Mode Off”. When scan barcode “Batch Data Output”, the stored scanned data will be immediately transmitted to the host. When scan barcode “Batch Data Clear”, all stored scanned data will be erased from memory. The capacity of this memory depends on the scanned data. The memory size is approximately 30,000 sets of EAN13 barcode type.

4.7 Out of Range When “Out of Range” function is enabled, and the scanner is working at out of transmission range, the scanned data will be stored to out-of-range memory. Memory size is approximately 25,000 sets of EAN13 barcode type. The all stored data will be transmitted to device when the link is reconnected, and the all data stored in out-of-range memory will be cleared.

10

4.8 Scanner Mode

<SPP Master Mode>

SPP Slave Mode

HID Slave Mode

BT Parameter Set Default

11

5. Configuring

5.1 Preface How to configure this device: The Barcode Programming Feature gives the possibility to change the scanner settings with programming codes. 5.2 Changing Scanner Settings with Programming Codes

The scanner can be configured by scanning all necessary programming codes that meet applications. To change the scanner settings please follow the sequence below:

1. Power up the scanner. 2. Open the scanner programming mode by

scanning 3. “Start Configuration”. 4. Change scanner setting by scanning any of

the programming codes that meet applications.

5. Close the scanner programming mode by scanning

6. “End Configuration”. 7. Save configuration by scanning “Save

Parameters”.

For example: To change the baud rate to 38400, scan the following codes successively: Start ConfigurationBaud Rate 38400End configuration Save Parameters After read a valid programming code, the scanner will give three high beeps and the green LED will light on. By scanning “Set All Default”, the setting will go back

12

to the factory default. 5.3 Programming Flow Chart

13

6. Programming Menu

Scan Set all Default bar code

6.1 General Process

1. 1 Power up the scanner

2. 2

Scan the Start of

Configuration bar code

3. 3 Scan the bar code for the desired feature. You can scan

all features before scanning End of Configuration.

4. 4 Scan End of Configuration

bar code

5. 5 Scan Save Parameters bar

code

6.1.1 Abort Configuration

6. Terminate current

programming status.

6.1.2 Recall

7. Replace the current

parameters by the

parameters saved last time

14

6.1.3 Version information

8. Scanner Firmware Version

Cradle Firmware Version

Scanner MAC Address

Cradle MAC Address

6.2 Set Cradle Interface

6.2.1 Interface

9. Keyboard Interface

10. RS232 Interface

11. <HID USB Interface>

12. USB Virtual Comport

6.3.1 Scanner Mode

<SPP Master Mode>

SPP Slave Mode

15

HID Slave Mode

BT Parameter Set Default

6.3.3 Batch Mode

*** Batch Mode (“***” means “Quick Setting Label”. The function can be executed directly by scanning barcode instead of doing the general programming process.)

<Out of Range Enable>

Out of Range Disable

Batch Mode ON

<Batch Mode OFF>

*** Batch Data Read

*** Batch Data Clear

***Delete Last Data

6.3.4 Sleep Mode

Sleep Mode <OFF>

Set Scanner to enter

Sleep Mode in 1 min

s Set scanner to enter

Sleep Mode in 10 min

16

6.3.5 Reading Mode

Default setting is shown with <> in Description.

13. Good Read <OFF>

Trigger ON/OFF

14. Continuous/Trigger OFF

15. Continuous/Auto Power ON

16. Flash

17. Flash/Auto Power ON

18. Testing

6.3.6 Good Read Led Control

19. Good read Led <ON>

Good read Led OFF

6.3

6.3.7 Beeper option

<High>

17

a. Medium

b. Low

Off

6.3.8 Reading Level

Bar Equals High

<Bar Equals Low>

6.3.9 Accuracy / Redundant Scan

20. <Original> - Require 1 good

decode for a good scan

1 Redundant Scan - Require 2

consecutive decodes of the

same bar code data for a

good scan

21. 2 Redundant Scan - Require 3



good scan

22. 3 Redundant Scan - Require 4



18

good scan

6.3.10 Sensitivity of Continuous Reading

This Feature is working under Reading Mode > Continuous

modes

<Fast>

Slow

6.3.11 Reverse Output Characters

Example: 012345 543210

Enable

<Disable>

6.3 RS232 mode parameters

6.4.1 Baud Rate

600

1200

2400

4800

19

9600

<19200>

38400

6.4.2 Data / Stop Bits

The number of data bits transmitted for each character

23. 7 Data Bits

< 8 Data Bits >

24. < 1 Stop Bits >

25. 2 Stop Bits

6.4.3 Parity

A Parity bit is an extra data bit used to help catch data

transmission errors.

26. <None>

Even – Select to set the parity

bit either a 1 or 0 to ensure an

even number of bits are 1’s

20

27. Odd – Select to set the parity

bit either a 1 or 0 to ensure an

odd number of bits are 1’s

28. Mark – Select to set the parity

bit always 1.

29. Space– Select to set the parity

bit always 0.

6.4.4 Handshaking

30. RTS/CTS ON– Output a Request

to Send (RTS) signal and wait for a

Clear to Send (CTS) signal before

transmitting data

RTS/CTS <OFF>

31. ACK/NAK – After transmitting data,

wait for host to send an ACK or a

NAK response. If ACK is received,

then complete the data

transmission. If NAK is received,

re-send the last set of data and wait

for ACK/NAK again.

32. ACK/NAK <OFF>

33. XON/XOFF – After transmitting

data, wait for host to send an XON

or a XOFF response. If XON is

21

received, then complete the data

transmission. If XOFF is received,

stop the transmission.

34. XON/XOFF <OFF>

6.4 Keyboard Wedge Mode Parameters

6.5.1 Terminal Type

35. <IBM PC/AT,PS/2> - Includes IBM

PS/2 and compatible models 50,

55, 60, 80

IBM PC/XT

36. PS/2 25, 30

37. IBM 5550

38. IBM 102 Key

39. IBM 122 Key (1)

40. IBM 122 Key (2)

41. NEC 9800

42. Apple Desktop Bus(ADB)

22

6.5.2 Country/Language

<US English>

UK English

Italian

Spanish

French

German

Swedish

Switzerland

Hungarian

Japanese

Belgium

Portuguese

23

Denmark

Netherlands

Turkey

6.5.3 Upper/Lower Case

43. <No Change>

Enable Lower Case – Transmit all

data as lower case

Enable Upper Case – Transmit all

data as upper case

6.5.4 Interscan Code Delay

44. <No Delay>

5 msec

10 msec

25 msec

50 msec

24

100 msec

200 msec

300 msec

6.5 Output Characters

6.6.1 Select Terminator

45. <CR+LF>– The scanner

transmits a carriage return and a

line feed after each scan

CR Suffix – The scanner

transmits a carriage return after

each scan

46. LF Suffix – The scanner

transmits a line feed after each

scan

47. Space

48. Tab

49. Alt

50. Disable Alt

25

51. STX-ETX – RS232 only

6.6 Code Type

6.7.1 Barcode Selections

If “Enable” is selected for all bar codes types, then the

scanner could read all types of bar code. If “Disable” is

selected for a certain bar code type, then the scanner could

not read the particular bar code. The symbol of “<>” means

default settings.

All Bar Codes ON

UPC-A <ON>

UPC-A OFF

UPC-E <ON>

UPC-E OFF

EAN-13 / JAN-13 <ON>

EAN-13 / JAN-13 OFF

EAN-8 / JAN-8 <ON>

26

EAN-8 / JAN-8 OFF

CODE 39 <ON>

CODE 39 OFF

Standard Code 39 <ON>

Full ASCII Code 39 ON

Code 32 / Italian Pharmacy

ON

Code32 / Italian Pharmacy

<OFF>

Code 128 <ON>

Code 128 OFF

Interleaved 2 of 5 <ON>

Interleaved 2 of 5 OFF

CODABAR/NW7 <ON>

CODABAR/NW7 OFF

27

Industrial 2 of 5 ON

Industrial 2 of 5 <OFF>

Matrix 2 of 5 ON

Matrix 2 of 5 <OFF>

CODE 93 ON

CODE 93 <OFF>

CODE 11 ON

MSI/PLESSEY ON

MSI/PLESSEY <OFF>

Telepen ON

Telepen <OFF>

China Postage ON

China Postage <OFF>

28

GS1 DataBar ON

GS1 DataBar <OFF>

GS1 DataBar Expanded ON

GS1 DataBar Expanded <OFF>

GS1 DataBar Limited ON

GS1 DataBar Limited <OFF>

6.7 UPC/EAN/JAN Parameters

6.8.1 Reading Type

UPC-A=EAN-13 ON

Add 0 before UPC-A to make it

13 digits.

<UPC-A = EAN-13> <OFF>

ISBN Enable

ISBN <Disable>

ISSN Enable

29

ISSN <Disable>

Decode with Supplement

<Auto discriminate

supplement>

6.8.2 Supplemental Setup

<Not Transmit>

2 Digit Supplemental

5 Digit Supplemental

2 & 5 Digit Supplemental

6.8.3 Check Digit Transmission

52. UPC-A Check Digit

Transmission <ON>

53. UPC-A Check Digit

Transmission OFF

54. UPC-E Check Digit

Transmission <ON>

55. UPC-E Check Digit

Transmission OFF

30

56. EAN-8 Check Digit

Transmission <ON>

57. EAN-8 Check Digit

Transmission OFF

EAN-13 Check Digit

Transmission <ON>

EAN-13 Check Digit

Transmission OFF

ISSN Check Digit

Transmission <ON>

ISSN Check Digit

Transmission OFF

6.8 Code 39 Parameters

6.9.1 Type of Code

<Standard Code 39>

Full ASCII Code 39


<Do not Calculate Check

Digit>

Calculate Check Digit and

Transmit

Calculate Check Digit and Not

Transmit

31

6.9.3 Output Start/Stop Character

Enable

<Disable>

6.9.4 Decode Asterisk

Enable

<Disable>

6.9.5 Set Up Code Length

To set the fixed length: (2 sets Available)

1. Scan the “Begin” programming code of the desired set

2. Go to the Decimal Value Tables in Appendix A, scan

programming codes that represents the length to be

read.

3. Scan the “Complete” programming code of the desired

set.

Repeat the steps 1 – 3 to set additional lengths.

<Variable>

32

Fixed Length 1st Set

1st Set Begin

Decimal Value See Appendix A

1st Set Complete

Fixed length 2nd Set

2nd Set Begin


2nd Set Complete

Minimum length

Minimum Length begin


Minimum Length Complete



Do Not Calculate Check Digit

33


Transmit

<Calculate Check Digit and

Not Transmit>

6.10.2 Append FNC2

ON

<OFF>






read.


set.

Repeat the steps 1 – 3 to set additional lengths

<Variable>


1st Set Begin


34

1st Set Complete


2nd Set Begin


2nd Set Complete

Minimum length




6.10 Interleaved 2 of 5 Parameters


<Do Not Calculate Check

Digit>


Transmit


Transmit

35

6.11.2 Set Up Number of Character

<Even>

Odd

6.11.3 Brazilian Banking Code

Enable

<Disable>






read.


set.


<Variable>

36


1st Set Begin


1st Set Complete


2nd Set Begin


2nd Set Complete

Minimum length




37

6.11 Industrial 2 of 5 Parameters


<Do Not Calculate Check Digit>


Transmit


Transmit



1. 1Scan the “Begin” programming code of the desired

set



read.


set.


<Variable>


1st Set Begin


38

1st Set Complete


2nd Set Begin


2nd Set Complete

Minimum length




6.12 Matrix 2 of 5 Parameters



Digit>


Transmit


Not Transmit

39






read.


set.


<Variable>


1st Set Begin


1st Set Complete


2nd Set Begin


2nd Set Complete

40

41

Minimum length


Decimal Value


6.13 CODABAR Parameters

6.14.1 Set Up Start/Stop Characters upon

Transmission

ON

<OFF>

6.14.2 Transmission Type of Start/Stop

A/B/C/D <Start>

A/B/C/D <Stop>

A Start

A Stop

B Start

42

B Stop

C Start

C Stop

D Start

D Stop






read.


set.


<Variable>


1st Set Begin


43

1st Set Complete


2nd Set Begin


2nd Set Complete

Minimum length






Calculate Check Digit Disable

<Calculate Check 2 Digit and

Not Transmit>

44






read.


set.


<Variable>


1st Set Begin


1st Set Complete


2nd Set Begin


2nd Set Complete

45

Minimum length







Digit>

Calculate Check 1 Digit and

Transmit


Not Transmit


Transmit


Not Transmit






read.

46


set.


<Variable>


1st Set Begin


1st Set Complete


2nd Set Begin


2nd Set Complete

Minimum length




47

6.16 MSI/plessey Code Parameters

6.17.1 Check digit transmission


Digit>


Transmit


Transmit






read.


set.


<Variable>


1st Set Begin


48

1st Set Complete

49


2nd Set Begin


2nd Set Complete

Minimum length




6.17 Telepen Parameters

6.18.1 Type of Code

Telepen ASCII <ON>

Telepen Numeric


Do Not Calculate Check

Digit


Transmit

50

<Calculate Check Digit

and Not Transmit>


o set the fixed length: (2 sets Available)




read.


set.


<Variable>


1st Set Begin


1st Set Complete


2nd Set Begin


51

2nd Set Complete

Minimum length




6.18 GS1 Databar Parameters



Transmit>


Transmit

6.19.2 Application ID

<Transmit Application ID>

Add 01 before GS1 Databar.

Don’t Transmit Application ID

6.19.3 Symbology ID

Transmit Symbology ID

Add ]e0 before GS1 Databar.

52

<Don’t Transmit Symbology

ID>

6.19 GS1 Databar Limited Parameters



Transmit>


Not Transmit

6.20.2 Application ID

<Transmit Application ID>

Add 01 before GS1 Databar

Limited.

Don’t Transmit Application ID

6.20.3 Symbology ID


Add ]e0 before GS1 Databar

Limited.


ID>

53

6.20 GS1 Databar Expanded Parameters

6.21.1 Symbology ID


Add ]e0 before GS1 Databar

Expanded.


ID>

54

7. Miscellaneous

Parameters

7.1 Bar Code ID

7.1.1 Default Barcode ID

With this function on, a leading character will be added to

the output string while scanning code; user may refer to the

following table to know what kind of barcode is being

scanned.

Code Type ID Code Type ID

UPC-A A UPC-E B

EAN-8 C EAN-13 D

Code 39 E Code 128 F

Interleaved 2 of 5 G Industrial 2 of 5 H

Matrix 2 of 5 I Codabar J

Code 93 K Code 11 L

China Postage M MSI/Plessey N

Telepen T GS1 DataBar U

GS1 DataBar

Lim.

V GS1 DataBar

Exp.

W

Bar Code ID ON

Bar Code ID <OFF>

55

Default – Return from User

Define to Default

7.1.2 User Define Code ID

To set the code ID

1. Scan the symbologies programming code.

2. Go to the ASCII Tables in Appendix B, Scan

programming codes that represents the desired ID.

Note: User defines code ID will override default value.

Program will not check the conflict. It is possible to have

more than two symbologies which have the same code ID.

UPC-A

UPC-E

EAN-13/JAN-13

EAN-8/JAN-8

CODE 39

CODE 128

CODABAR

56

Interleaved 2 of 5

Industrial 2 of 5

Matrix 2 of 5

CODE 93

CODE 11

China Postage

MSI/PLESSEY

Telepen

GS1 DataBar

GS1 DataBar Expanded

GS1 DataBar Limited

7.2 preambles and postambles Insertion

7.2.1 Setup Insertion

To set the insertion of the output characters;

1. Scan the programming code of the desired set.

57

2. Scan the programming code of the desired symbology

3. Go to the Decimal Value in Appendix A, scan

programming codes that represents the desired

position to be inserted (1= the first digit, 99 the last

digit).

4. Scan the “Complete” programming code of “Character

Position to be inserted”.

5. Go to the ASCII Tables in Appendix C, Scan


characters to be inserted.

6. Scan the “Complete” programming code of

“Characters to be inserted”.

Repeat the steps 1 – 6 to set additional insertion.

Example: Insert $ as Preamble for Code UPC-A.

Start configuration

1st Set

Code UPC-A

1st digit

Complete

$

58

Complete

End of Configuration bar

code

Save Parameters bar code

7.2.2 Insertion set number

1st Set

2nd Set

3rd Set

4th Set

5th Set

6th Set

7.2.3 Symbologies Selection

UPC-A

UPC-E

EAN-13/JAN-13

59

EAN-8/JAN-8

CODE 39

CODE 128

Codabar/NW7

Interleaved 2 of 5

Industrial 2 of 5

Matrix 2 of 5

CODE 93

CODE 11

China Postage

MSI/PLESSEY

Telepen

GS1 DataBar

60


GS1 DataBar limited

All Codes

None

7.2.4 Character Position to be inserted


Complete

7.2.5 Characters to be Inserted

ASCII Table See Appendix B and C

Complete

7.3 Character deletion

To setup the deletion of output characters:

1. Scan the programming code of the desired set.

2. Scan the programming code of the desired

symbology.

61

3. Go to the decimal Value tables in Appendix A, scan


position to be deleted.

4. Scan the “Complete” programming code of “Character

Position to be Deleted”.


programming codes that represents the number of

characters to be deleted.

6. Scan the ”Complete” programming code of “Number

of Characters to be deleted”.

Repeat the steps 1 – 6 to set additional deletion.

Example: Delete first 3 codes for Code EAN-13.

Start Configuration

1st Set

Code EAN-13

1st digit – delete from the

1st digit

Complete

3 – delete 3 characters

62

Complete

End of Configuration bar

code

Save Parameters bar code

63

7.3.1 Deletion Set Number

1st Set

2nd Set

3rd Set

4th Set

5th Set

6th Set

7.3.2 Code Type to be Delete

UPC-A

UPC-E

EAN-13/JAN-13

EAN-8/JAN-8

CODE 39

CODE 128

64

CODABAR/NW7

Interleaved 2 of 5

Industrial 2 of 5

Matrix 2 of 5

CODE 93

CODE 11

China Postage

MSI/PLESSEY

Telepen

GS1 DataBar


GS1 DataBar Limited

All Codes

65

None

7.3.3 Character Position to be Delete


Complete

7.3.4 Number of Characters to be Deleted


Complete

7.4 Appendices

A. Decimal Value Table

66

B ASCII Table

NULL

RS

ETX

STX

ACK

ENQ

HT

BS

FF

VT

SI

SO

DC2

DC1

NAK

DC4

CAN

ETB

ESC

SUB

GS

SYN

SOH

EM

67

BEL

US

LF

SPACE

CR

″

DLE

!

DC3

#

%

0

$

1

&

2

(

3

'

4

)

5

+

6

*

7

68

,

Comma

8

.

period

9

-

minus

B

/

C

;

D

:

E

<

Less than

F

>

Greater

than

G

=

H

?

I

Letter I

@

J

A

K

L

T

69

M

U

N

V

O

Letter O

W

P

X

Q

Y

R

Z

S

[

]

\

^

_

Underscore

`

a

h

b

i

c

j

70

d

k

e

l

f

m

g

n

o

u

p

v

q

w

r

x

s

y

t

z

{

|

Vertical

slash

}

~

DEL

71

C Function Key Table

F1

F7

F2

F8

F3

F9

F4

F10

F5

F11

F6

F12

Insert

Delete

Home

End

Page

Up

Page Down

Up

Left

Down

72

D. Decimal Value Table

0

1

2

3

3

4

5

6

7

8

9

Enter

73

E. Technical Specifications a) Physical Characteristics

Weight BT-‐8500 Scanner Cradle

Accessory KBW Cable RS232 Cable USB Cable AC Adaptor

Approx. 210g Approx. 105g Approx. 75g Approx. 123g Approx. 67g Approx. 125g

Material ABS Plastic Connector RJ 45C 10Pins Cable Length 5Ft. (150mm) Dimension Scanner Cradle

193x90x72mm 206x101x49mm

b) Performance Scanner Characteristics

Light Source Visible Red Light 650nm ± 10nm

Scan Rate Smart detect up to maximum 500 scans/second ±10%

Sensor Linear CCD Sensor Processor Type ARM Cortex™-‐M3, 32-‐bit Operating Freq. 8 MHz Depth of Field Up to 500mm@20mil,

PCS90%, Code39 Print Contrast Ratio

45%

Resolution 4mil(0.1mm)@PCS90% Scan Angle Forward & Backward(Pitch)

±10°~65°(±5°) Left & Right(Skew) ±60°(±5°)

Interface SG-‐300BT Cradle

KBW, RS-‐232, USB (HID KBW), Virtual Comport

Ambient Light 10,000 Lux Max.

74

c) Bluetooth Characteristics Bluetooth Module Bluetooth V2.0 Standard

Frequency Band 2.402GHz ~ 2.480GHz

Modulation Method GFSK for 1Mbps

RF Output Power Under 20dBm (Class 1)

Bluetooth Distance Range

Class1 ; 100M line of sight

Data Storage on BT Disconnect

30,000 scans for EAN13

F. Indicator LED Status

a) Cradle Light Signal Status

Green 1 blink good read and transmitted

continuous on power on Red

off power off

2 blink BT disconnect Blue

continuous on BT connected b) Scanner

Light Signal Status good read and transmitted

1 blink and 1 beep good read and save on memory (BT disconnect)

Green

continue on battery charged full

red blink 2 times and 2 long beeps

memory full

down-‐tone enter sleep mode

red blink 1 time and beep per 20 seconds

battery low warning

red blink 4 times and bi-‐bi-‐bi-‐bi per 10 seconds

battery very low power alarm

2 short blink and 2 short beeps

good read but transmit fail

Red

continue on in charging blue light 2 second and Down tone

BT disconnect Blue

blue blink 2 times per on connecting

75

second

blue blink per second BT connected

blue light 2 second and up-‐tone

BT connecting succeed

Red Blue

1 blink at the same time and 2 beeps

setting ok

G. Electrical Characteristics a)

Scanner Power Battery Li-‐ion 3.7V / 1100 mA. Charge Time 3.5 hours Reads per Charge 10,000 Times Power Consumption Power On 190mA Stand by 50mA Operation 150mA Sleep 6mA

Cradle

Input Voltage 5 VDC @ 2 A / Input AC

110-‐240V Power Consumption Power On 95mA Stand By 55mA Operation 70mA

b) Environmental

Operating Temp 0°C to 50°C Storage Temp. -‐20°C to 70°C Relative Humidity 0 to 95% non-‐condensing Ambient Light 100,000 Lux (direct

sunlight) c) Regulatory of Compliance

FCC, CE, RoHs

76

H. Scan Map

How to communicate with Smartphone 1) Make the device discoverable. (Page 8

4.3,4.4) 2) See the documentation that came with the

device. 3) Go to Settings > Bluetooth and turn

Bluetooth on. 4) Select the ‘barcode scanner’ device and,

if prompted, enter the passkey or PIN. See the instructions (page 69) about the passkey or PIN that came with the device.

77

A. How to communicate with Bluetooth dongle

1) Switch the Scanner SPP HID mode or SPP Slave mode. (Page 8 4.3,4.4)

2) Active the BT dongles software to search the Bluetooth device.

3) Select the ‘barcode scanner’ device to pairing; When pairing, it will request key in the (PINCODE), Please refer to page 69 for Help.

4) After pairing completed, connection can be carried out.

5) Scanner SPP Slave mode, after a successful connection, BT Dongle software will provided virtual comport, if need to check the data output , Please activate the Hyper Terminal program, and setup the RS232 parameter(com port number and baud rate) then you can see the data output.

6) Scanner SPP HID mode after the connection successful, only need to activate the general editing software (For example: notepad, word. etc) then you can see the data output.

ATTENTION: Compatible to Bluetooth V2.1+EDR, V2.0+EDR, V1.2,V1.1 or backward version Class1 and Class 2 dongles, The transmission distance is depends on the environmental conditions and the dongle as a Class 1 or Class 2 may be. Due to Champtek’s continuing product improvement programs, specifications and features are subject to change without notice.

Documents

Wireless’HandheldLinear’Imager’Barcode’Scanner’ User’s Manual User Man… · 2D imager hand held barcode scanner. This is a cutting-edge gun-type area imaging barcode