9
Wireless Relay User Manual Revision: 01 Revision Date: 2012/09/25 ATrack Technology Inc. 3F., No. 88, Sec. 1, Neihu Rd., Neihu Dist., Taipei City 11493, Taiwan (R.O.C.) Tel: +886-2-27975852 Fax: +886-2-27974030 http://www.atrack.com.tw

Wireless Relay User Manual

Embed Size (px)

Citation preview

Page 1: Wireless Relay User Manual

Wireless Relay User Manual

Revision: 01

Revision Date: 2012/09/25

ATrack Technology Inc.

3F., No. 88, Sec. 1, Neihu Rd., Neihu Dist.,

Taipei City 11493, Taiwan (R.O.C.)

Tel: +886-2-27975852

Fax: +886-2-27974030

http://www.atrack.com.tw

Page 2: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 2 of 9

Contents

1.  Notification .............................................................................................................................. 3 1.1.  Disclaimer .................................................................................................................................... 3 1.2.  Copyright ...................................................................................................................................... 3 1.3.  Warning ........................................................................................................................................ 3 

2.  Introduction ............................................................................................................................. 4 2.1.  Wireless Relay Operation ............................................................................................................ 4 

3.  Installation ............................................................................................................................... 5 3.1.  AX5 Configuration ........................................................................................................................ 5 3.2.  Wireless Module Installation ........................................................................................................ 5 3.3.  Wireless Relay Installation ........................................................................................................... 6 3.4.  Wireless Relay Testing ................................................................................................................. 7 3.5.  LED Indications ............................................................................................................................ 7 

4.  Appendix .................................................................................................................................. 8 4.1.  Hardware Specification ................................................................................................................ 8 4.2.  FCC Regulations: ......................................................................................................................... 9 

Page 3: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 3 of 9

11.. NNoottiiffiiccaattiioonn

11..11.. DDiissccllaaiimmeerr

This document, and all other related products, such as device, firmware, and software, is developed by

ATrack Technology Inc. thoroughly. At the time of release, it is most compatible with specified firmware version.

Due to the functionalities of the devices are being developed and improved from time to time, the change in

the protocol, specification, and firmware functions are subjects to change without notice. ATrack Technology

Inc. is obligated to modify all the documentation without the limitation of time frame. A change notice shall be

released to ATrack Technology Inc. customers upon the completion of document modification.

ATrack Technology Inc. products are not intended to be used as life support or rescue equipments. ATrack

Technology Inc. is not liable for any loss or injury caused by using or referencing to any products. Any possible

means of using or integrating ATrack Technology Inc. products shall be avoided.

11..22.. CCooppyyrriigghhtt

ATrack Technology Inc. holds all parts of intellectual rights applicable in the copyright laws in all the countries.

Any or all parts of this document shall not be exposed to non-authorized party without any form of approval

from ATrack Technology Inc. Any forms, including but not limited to oral, copy, or internet sharing, of releasing

or exposing information to an unauthorized party shall be prohibited. ATrack Technology Inc. reserves the

rights of litigation in the violation of such copyright laws.

11..33.. WWaarrnniinngg

Connecting the wire inputs can be hazardous to both the installer and your vehicle’s electrical system if not

done by an experienced installer. This document assumes you are aware of the inherent dangers of working

in and around a vehicle and have a working understanding of electricity.

Page 4: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 4 of 9

22.. IInnttrroodduuccttiioonn

The Wireless Relay is used for ignition/starter kill application which controlled by ATrack AX5 OBD-II

GPS/GPRS device. The relay ON/OFF state can be controlled by remote application server or SMS via

cellular phone. It can be also controlled by itself when the AX5 device is unplugged. It utilizes short range RF

technology and bi-directional data transmission between AX5 device and Wireless Relay. It’s a benefit to hide

the Wireless Relay in anywhere of the vehicle.

The Wireless Relay is an extended accessory of the AX5. This accessory contains a Wireless Relay with

harness and a wireless module.

• Wireless Relay

• Wireless Module

22..11.. WWiirreelleessss RReellaayy OOppeerraattiioonn

The AX5 device will keep communication with Wireless Relay for every 30 seconds.

There are 3 modes for the Wireless Relay operation:

(1) Relay always ON

(2) Relay always OFF

(3) Timeout Mode

When Wireless Relay gets signal from AX5 device, the Relay will ON. When AX5 device is unplugged and

Wireless Relay does not receive RF signal within 90 seconds, the Relay will OFF.

Page 5: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 5 of 9

33.. IInnssttaallllaattiioonn

33..11.. AAXX55 CCoonnffiigguurraattiioonn

The Wireless relay shall be paired with one AX5 device before installing it to the vehicle. The Wireless Relay

serial number shall be entered into the AX5 device. Please refer to command description below.

Please note that the AX5 Wireless Relay function is supported only with AX5 firmware version 1.07 or higher.

AT Command Syntax:

AT$RFPD=<”Relay Serial Number”>

Example:

AT$RFPD=”EB017F01”

33..22.. WWiirreelleessss MMoodduullee IInnssttaallllaattiioonn

Please see the figure and installation procedure below for Wireless module installation:

(1) Open the top cover of the AX5

(2) Find the dual-raw 8-pin black socket on the PCB.

If there is no socket on the PCB, the AX5 would be an older version and will not support Wireless module.

(3) Plug the Wireless module into the socket and close the top cover of the AX5.

Wireless Module

AX5

Relay Serial number

Page 6: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 6 of 9

33..33.. WWiirreelleessss RReellaayy IInnssttaallllaattiioonn

The Wireless Relay is for engine/starter kill application. For safety reasons, it is recommended to connect the

Wireless Relay to control the starter of vehicle. Do NOT use the Wireless Relay to control fuel pump or ignition

power of vehicle. Please follow instructions below to install the Wireless Relay.

(1) Connect white(85) wire to the constant 12V of the vehicle.

(2) Connect black(86) wire to the ground.

(3) Finding the starter wire on the ignition switch

(4) Breaks continuity of the wire between the ignition switch and the starter motor.

(5) Connect blue(30) wire to the wire at ignition switch side.

(6) Connect yellow(87) wire to the wire at the starter motor side.

The starter kill Wireless Relay diagram is shown below:

85 White 86 Black

30 Blue 87 Yellow

Wireless Relay

Starter Motor

Ignition Switch

12V Battery

Page 7: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 7 of 9

33..44.. WWiirreelleessss RReellaayy TTeessttiinngg

The Wireless Relay testing can be performed by using AT command via GPRS server or SMS. Please see the

AT command description below:

Command Syntax Command:

AT$OUTC=<Output ID>,<Output Mode>

Response:

$OK Parameter Description Parameter Description

<Output ID> The <Output ID> is 10 for the Wireless Relay

<Output Mode> 0- Relay always OFF

1- Relay always ON

2- Timeout Mode (Default Mode)

When Wireless Relay get signal from AX5 device, the Relay will ON. When

AX5 device is unplugged and Wireless Relay no RF signal for 90 seconds,

the Relay will OFF.

33..55.. LLEEDD IInnddiiccaattiioonnss

The status LED helps to know the current status of the Wireless Relay for troubleshooting.

The following table describes the LED operation of the Wireless Relay:

Wireless Relay ON Wireless Relay OFF

RF Signal received 1 pulse/30secs 2 pulse/30secs

RF Signal not received 3 pulse/30secs 4 pulse/30secs

See the following figure for the status LED location

Status LED

Page 8: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 8 of 9

44.. AAppppeennddiixx

44..11.. HHaarrddwwaarree SSppeecciiffiiccaattiioonn

Wireless Relay

Max. Carrying Current 45A/2 minutes, 35A/1 hour @ DC16V 20°C

RF Frequency 433MHz

RF Output Power -15dBm (0.03mW)

Modulation GFSK

Receiver Sensitivity -112dBm

Frequency Tolerance ±40ppm

Supply Power DC8V~DC16V

Standby Current 0.9mA @ DC12V

Active Current 40mA @ DC12V

Operating Temperature -40°C ~ +85°C

Operating Humidity 5% R.H. to 85% R.H.

Page 9: Wireless Relay User Manual

Confidential Document

© ATrack Technology Inc. All Rights Reserved. Page 9 of 9

44..22.. FFCCCC RReegguullaattiioonnss::

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiated radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in

a particular installation If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the

user‘s authority to operate the equipment.

4RF Exposure Information

This device meets the government’s requirements for exposure to radio waves.

This device is designed and manufactured not to exceed the emission limits for exposure to radio

frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In

order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to

the antenna shall not be less than 20cm (8 inches) during normal operation.