Welcome to

ROVR/ROVR+®

• worldVIEW™ and ROVR® Introduction• ROVR/ROVR+ Installation Manuals• Multi-driver ID Manual

Welcome Packet & Installation Guide includes:

CRT_ROVR_Welcome_Packet_Nov2017.indd 1 11/21/17 9:01 AM

2

INTRODUCTIONWELCOME

Thank you for choosing ROVR® as your driving safety system.

Introduction Page 2-3

ROVR® Direct Connect Page 4

ROVR® Standard Connect Page 5-11

Driving is one of the most dangerous parts of almost any job. The National Institute for Occupational Health and Safety has shown that implementing an in-vehicle monitoring system combined with a driving safety program can have a significant reduction in injuries involving motor vehicles.

Our approach with ROVR® is to focus on the leading indicators of risk and positively engage drivers with effective feedback – the key to changing any human behavior.

MINIMIZE RISK ON THE ROADWELCOME TO ROVR/ROVR+®

“Implementing an In-Vehicle Monitoring Program: A Guide for the Oil & Gas Extraction Industry” by National Institute for Occupational Health and Safety

CRT_ROVR_Welcome_Packet_Nov2017.indd 2 11/21/17 9:01 AM

3

1. DRIVER SAFETYSCORECARDEach week you receive a Driver Safety Scorecard that scores you on the previous week’s driving behavior. We focus on three key metrics that are the most signifi cant for a driver: speeding, hard braking and rapid acceleration. You will receive a letter grade for each metric.

2. NOTIFICATIONSNot sure if that was a hard braking event? Set up a notifi cation in worldVIEW™ to notify you when you have a hard braking event. Notifi cations of various event types can be sent to your event stream in the worldVIEW Dashboard, to your email, and even to your phone as a message.

INTRODUCTION WELCOME

SAFE DRIVING TOOLS

worldVIEW now

MINOR HARD BRAKING event at FM 2204, Gregg, TX, USA, 75603 (32.3814735,-94.7457657) at 12:23:43 PM

3. TRIP REPORTSHow was my driving? With worldVIEW and your ROVR device, it is now possible to receive instant feedback about your trip. Once you reach your destination, you will receive a Trip Report in your email giving you a brief overview of your trip including all speeding, rapid acceleration and hard braking events.

4. TRIP DETAILSAll of your trips and events report to worldVIEW making it your one-stop destination to view your entire driving history. Want to know where that speeding event occurred? Click on the Details Tab and locate the event. Need help? Check out our Reference Guide.

CRT_ROVR_Welcome_Packet_Nov2017.indd 3 11/21/17 9:01 AM

4

ROVR® DIRECT CONNECT GUIDEDIRECT CONNECT

STEP 1Locate and orient the ROVR On Board Diagnostic (OBD) connector for the OBD Port in your vehicle.

STEP 2Connect the OBD end of the ROVR (A1) into the vehicle’s OBD port (A2).

NOTE: The On Board Diagnostic Port is usually found below the driver side’s dashboard within two feet of the driver.

Your vehicle OBD Port

ROVR

A1

A2

ROVR® DIRECT CONNECT

CRT_ROVR_Welcome_Packet_Nov2017.indd 4 11/21/17 9:01 AM

5

cartasite.com

realtime operational intelligence CDMA

P/N: LMU26C4V0-CAR01ESN: 4641117108MSN-D:

MSN-H:

270113179707789153

A100001576DA61

FCC ID: R5Q-LISAC200A IC: 8595B-LISAC200AThis device complies with part 15 of the FCC Rules. Operation is subjectto the condition that this device does not cause harmful interference .

4213 Assembled in USA.

cart

asi

te.c

om

realtim

e o

pera

tio

nal i

nte

llig

ence

CDM

A

P/N

: LM

U26

C4V0

-CAR

01ES

N:

4641

1171

08M

SN-D

:

MSN

-H:

2701

1317

9707

7891

53

A100

0015

76D

A61

FCC

ID: R

5Q-L

ISA

C200

A

IC: 8

595B

-LIS

AC2

00A

This

dev

ice

com

plie

s w

ith p

art 1

5 of

the

FCC

Rule

s. O

pera

tion

is s

ubje

ctto

the

cond

ition

that

this

dev

ice

does

not

cau

se h

arm

ful i

nter

fere

nce

.

4213

Asse

mbl

ed in

USA

.

ROVR® STANDARD CONNECT GUIDE

Wire Connectors (4)

Ring Terminal (1)

STANDARD CONNECT

ROVR+®INCLUDED HARDWARE

RECOMMENDED TOOLS:• Volt Meter• Socket Set• Wire Cutters• Wire Crimper• Screwdrivers• Needle Nose Pliers

TIP: You will either have the MSN-D number or the IMEI number on the top of your ROVR. However, there will always be an ESN number for your reference.

MSN-D/IMEI*Number Here

ROVR+ with Tetra Cable

Fuse Taps (4)

CRT_ROVR_Welcome_Packet_Nov2017.indd 5 11/21/17 9:01 AM

6

DO NOT install ROVR+ under metal. Metal obstructions above the unit interfere with GPS satellite signal.

DO NOT install ROVR+ in direct sunlight or in areas where likely to get wet.

ROVR+® HARDWIRE INSTALL

STEP 1: DETERMINE PLACEMENTPlace the ROVR+ within the vehicle dash making the following considerations:• Install horizontally with label facing up• Avoid areas with heat or moisture• Clean off any dust before attaching ROVR+• Make device accessible for future maintenance• LED indicators (located to the upper right of the cable

to device) are visible if possible

A

B

ROVR+ can be placed in the following locations:

ROVR® STANDARD CONNECT GUIDESTANDARD CONNECT

CRT_ROVR_Welcome_Packet_Nov2017.indd 6 11/21/17 9:01 AM

7

Figure 1.1

Figure 1.2

Small Fuse Configuration

SmallFuse Tap

Large Fuse Tap

Small Wire Connector

Large Wire Connector

STEP 2: CONNECT RED WIRE TO A FUSE WITH CONTINUOUS POWER 1. Use the multimeter to locate a fuse in the fuse panel that

has voltage present at all times regardless of the position of the ignition switch (Figure 1.1).

2. Remove the fuse.3. Attach the red power wire using a fuse tap and a wire

connector of the appropriate size, depending on the fuse (see Figure 1.2).*

4. Place the original fuse back into the panel where it was removed.

*If you have micro fuses, replace the fuse with a small fuse included in the supply kit. Small fuses fit in the same micro fuse slot.

TIP

ROVR® STANDARD CONNECT GUIDE STANDARD CONNECT

CRT_ROVR_Welcome_Packet_Nov2017.indd 7 11/21/17 9:01 AM

8

Figure 1.3

Figure 1.2

Small Fuse Configuration

Large Fuse Configuration

SmallFuse Tap

Large Fuse Tap

Small Wire Connector

Large Wire Connector

STEP 3: CONNECT WHITE WIRE TO A FUSE WITH SWITCHED POWER 1. Use the multimeter to locate a fuse in the fuse panel that

has voltage present only when the ignition switch is in the Run/On position (Figure 1.3). The fuse is switched when voltage returns to ZERO after the ignition is off.

2. Remove the fuse.3. Attach the white power wire using a fuse tap and a wire

connector of the appropriate size, depending on the fuse (see Figure 1.4).

4. Place the original fuse back into the panel where it was removed.

ROVR® STANDARD CONNECT GUIDESTANDARD CONNECT

CRT_ROVR_Welcome_Packet_Nov2017.indd 8 11/21/17 9:01 AM

9

Figure 1.7

STEP 4: GROUND POWER CABLE CONFIGURATION1. Locate a ground attachment point. Find a bolt or nut that is

attached to bare metal.2. Secure the ground (black) wire using the appropriate size

ring terminal (Figure 1.5).3. The final fuse box three-wire installation should look like

Figure 1.6.4. Plug the 20-pin connector on the other end of the power

cord into the ROVR+ port (Figure 1.7).

Figure 1.5

Figure 1.6

Ground

Continuous

Switched

ROVR® STANDARD CONNECT GUIDE STANDARD CONNECT

CRT_ROVR_Welcome_Packet_Nov2017.indd 9 11/21/17 9:01 AM

10

ORANGE LED CONDITION

Off Modem OffSlow Blinking Searching for NetworkFast Blinking Network Available - Attempting to ConnectSolid Connected to Network

GREEN LED CONDITIONOff GPS OffSlow Blinking On - SearchingFast Blinking Determining LocationSolid Location Obtained

ORANGE LED

GREEN LED

COMM

GPS

STEP 5: CONFIRM CONNECTION WITH LED GUIDEROVR+ has two status LEDs that use blink patterns to indicate service. To ensure a trouble-free installation, wait until both LED lights are solid before completing installation.

NOTE: It may take up to 3-5 minutes to establish initial GPS satellite & cellular connection.

ROVR® STANDARD CONNECT GUIDESTANDARD CONNECT

CRT_ROVR_Welcome_Packet_Nov2017.indd 10 11/21/17 9:01 AM

11

STEP 6: INSTALL ROVR+ UNDER DASH AS DETERMINED IN STEP 1.Use velcro and/or included zip ties to secure the ROVR+ into place.

TIPDisconnect ROVR if you are jump starting your vehicle. Jump starting the vehicle with ROVR installed will damage the ROVR device.

INSTALLATION COMPLETEYour ROVR+ can now be monitored using the worldVIEW™ web application.

TIPTo ensure a proper connection take the vehicle outside. It can take up to 5 minutes for the ROVR+ to aquire a GPS signal with an unobstruted view of the sky.

ROVR® STANDARD CONNECT GUIDE STANDARD CONNECT

A

B

ROVR+ can be placed in the following locations:

CRT_ROVR_Welcome_Packet_Nov2017.indd 11 11/21/17 9:01 AM

If you have any additional questions or concerns, please call Customer Care at 1-877-516-9373, email customercare@cartasite.com or visit support.cartasite.com

ROVR/ROVR+®

CRT_ROVR_Welcome_Packet_Nov2017.indd 12 11/21/17 9:01 AM