Waterproofing Systems · • ™Mapeflex P2 NS and Mapeflex P1 for detailing and penetrations. • Mapethene Mastic for sealing terminations. • Mapedrain ™ drainage composites,

Waterproofing Systems

Waterproofing

• Cold-Fluid-Applied Waterproofing Membrane

• Bentonite Clay Waterproofing Membranes

• Self-Adhering Sheet Waterproofing Membranes

• Prefabricated Drainage Composites

• Waterproofing Accessories

• Surface-Preparation Products

ii 1-800-42-MAPEI (1-800-426-2734) • www.mapei.com

PRODUCTS FOR WOOD FLOORING

CONCRETE RESTORATION SYSTEMS

TILE & STONE INSTALLATION SYSTEMS

PRODUCTS FOR STRUCTURAL STRENGTHENING

ADMIXTURES FOR CONCRETE

PRODUCTS FOR UNDERGROUND CONSTRUCTION

CEMENT ADDITIVES

PRODUCTS FOR THE MARINE INDUSTRY

Product Lines of North America

FLOOR COVERING INSTALLATION SYSTEMS

WATERPROOFING SYSTEMS

11-800-42-MAPEI (1-800-426-2734) • www.mapei.com

TABLE OF CONTENTS

Introduction .............................. 2-3

COLD-FLUID-APPLIED WATERPROOFING MEMBRANE Planiseal ® CR1 .....................................4

BENTONITE CLAY WATERPROOFING MEMBRANES Mapeproof ™ HW and Mapeproof SW ...5

SELF-ADHERING SHEET WATERPROOFING MEMBRANES Mapethene™ HT and Mapethene LT ......6

PREFABRICATED DRAINAGE COMPOSITES Mapedrain™ 10 ......................................7

Mapedrain 20 ........................................7

Mapedrain 25 ........................................7

Mapedrain 30........................................7

Mapedrain 40 ........................................7

Mapedrain 50 ........................................8

Mapedrain TD Drainage Composite ......8

Mapedrain TD Fittings ..........................8

WATERPROOFING ACCESSORIES

Contact Adhesives Mapebond ™ 700 ...................................9

Mapebond 710 ......................................9

Mapebond 720 ......................................9

Detailing Accessories Mapethene Mastic ..............................10

Mapeflex ™ P2 NS ...............................10

Mapeflex P1 ........................................10

Mapecover ™ 810 .................................10

Idrostop™ 25 .......................................10

Idrostop B25 .......................................10

Mapeproof Granules ...........................10

Mapeproof Sealant .............................10

MAPEI LMR Fabric ..............................11

Mapeband ™ TPE .................................11

Planibond ® AE ....................................11

SURFACE-PREPARATION PRODUCTS Planiseal 88 ........................................12

Planitop® X .........................................12

Planitop XS .........................................12

Planicrete® AC ....................................12

2 1-800-42-MAPEI (1-800-426-2734) • www.mapei.com

Introduct ion

A WORLDWIDE LEADEROriginally established in 1937, today MAPEI is a privately

owned global corporation headquartered in Milan, Italy,

with 87 subsidiaries including 81 plants in 35 countries. The

company specializes in manufacturing chemical products

for building, including waterproofing products, specialty

mortars and admixtures for concrete, products to restore

historic buildings, and decorative and protective coatings

for concrete surfaces. In addition, MAPEI is the world leader

in the manufacturing of mortars, grouts, adhesives and

complementary products for installing all types of floor and

wall coverings. MAPEI Corporation, the division responsible

for supporting the North American markets, is based in

Deerfield Beach, Florida, and employs over 1,100 team

members – ranging from Manufacturing and R&D to Technical

Services and Sales. The Canadian subsidiary MAPEI Inc.

supports those efforts with about 300 additional employees.

SUPERIOR PRODUCTS

A Complete Range of Products

MAPEI produces the most innovative products for the

construction market. More than 5,000 products globally

(adhesives, sealants, mortars, admixtures, latex, etc.) are

manufactured in MAPEI’s plants, which produce the world’s

most complete range of building products. Diversified, high-

quality chemical products – from powdered adhesives, to

liquid and paste products, to polymers – are created to meet

the needs of more than 66,000 customers around the world.

Quality Control

MAPEI is an ISO 9001-2000 certified company. Its

products are produced according to exacting standards,

strictly adhering to process and procedural guidelines with

documented compliance. This rigid production format is

vigilantly followed to ensure that every product is produced

uniformly from batch to batch.

PROFESSIONAL SUPPORT NETWORK

Knowledgeable Sales Force

MAPEI offers the largest, most highly trained sales

force within the industry to serve your needs for product

application/installation recommendations. Its sales

representatives are focused on supporting you with product

knowledge, product demonstrations, product information,

marketing support materials and other relevant tools to help

you generate sales.

Technical Expertise

An in-house Technical Services Call Center responds to

customers’ telephone inquiries with answers to installation

challenges in real time. In addition, MAPEI can offer field

support for job startups, product training and on-site problem

resolution.


Customer Service Plus

MAPEI’s standards for customer service are best-in-class. Our leadership

includes such service innovations as:

• Customer-friendly, efficient processes

• One-call resolution

• Employee commitment to effective customer dialog

Innovative Research & Development

Worldwide, more than 12% of MAPEI employees are involved in the

development of new technologies and product innovations, keeping our

customers at the forefront of the industry. The company has taken the additional

initiative of focusing its R&D efforts on environmentally sustainable solutions.

To remain on the cutting edge of innovation, MAPEI reinvests 5% of its annual

revenues into researching and developing new products and technologies; in

particular, 70% of its R&D efforts are directed to develop eco-sustainable and

environmentally friendly products.

Best-BackedSM Warranty Program

To bring it all together, MAPEI

complements the industry’s best

products with simple, easy-to-

understand requirements for a

variety of warranty options.


Cold-F luid-Applied Waterproof ing Membrane

Single-Component, 100%-Solids, Cold-Fluid-Applied, Structural Waterproofing MembranePlaniseal CR1 is a fast-curing, 100%-solids, cold-fluid-applied, single-component, moisture-curing, structural waterproofing membrane that will not shrink and is VOC-compliant in virtually all municipalities. Very low in odor, it is well suited for use in and around occupied spaces. Thanks to advanced proprietary technology, this single-grade membrane can be used in horizontal as well as vertical applications, maximizing versatility. Planiseal CR1 can be applied by roller, brush, trowel or squeegee.

Features and benefits:• Single-grade membrane for vertical and horizontal applications• Suitable for green concrete• Seamless and monolithic • Does not require a primer• Applies easily with no mixing or special equipment required• Free of solvents• Very low odor• Free of tar and asphalt • Compatible with common construction materials such as concrete,

concrete masonry units (CMUs), stone, metal, wood (pressure-treated and fire-treated), rigid insulation and insulating concrete forms (ICF)

Applications:• Vertical and horizontal waterproofing on structural foundation walls

and decks• Vertical and horizontal waterproofing on tunnels, plaza decks,

balconies, split slabs, courtyards, planters, parking decks and bridges• Interior applications such as bathrooms, kitchens, mechanical rooms

and laboratories • Suitable for use in confined spaces and occupied buildings

The Planiseal CR1 structural waterproofing system includes:• Planiseal CR1 waterproofing membrane.• MAPEI LMR Fabric liquid membrane reinforcing fabric.• Mapedrain™ drainage composites to protect the Planiseal membrane

and to filter and channel water away from the structure.• Mapecover ™ 810 protection board.• Mapeflex ™ P2 NS and Mapeflex P1 for detailing and penetrations.• Idrostop ™ 25 and Idrostop B25 expandable waterstops.

Planiseal ® CR1


Bentoni te Clay Waterproof ing Membranes

Mapeproof™ HW and Mapeproof SWSodium Bentonite Waterproofing MembranesMAPEI’s Mapeproof sodium bentonite waterproofing membranes have been proven, worldwide, to be the most consistent and reliable products of their kind. Certified as manufactured in accordance with ISO 9001, both Mapeproof HW and Mapeproof SW are constructed using a layer of woven and nonwoven, puncture- and tear-resistant polypropylene fabrics. Encased within these fabrics is high ‐swelling, self ‐sealing sodium bentonite; loaded at an industry leading rate of 1.1 lbs. per sq. ft. (5.3 kg per m2), minimum. The process by which the sodium bentonite is encased within these fabrics ensures that, regardless of hydration cycles and/or the geometric plane in which it is installed, the membrane will perform as designed.

When hydrated, Mapeproof membranes form a monolithic membrane with very low permeability, protecting underground structures from water ingress. Designed for sites where contaminated or salt groundwater is present, Mapeproof SW also contains a proprietary polymer to ensure that the membrane performs as designed when hydrated.

Features and benefits:• Can be installed over damp or green concrete• Self-healing if punctured• Creates a strong mechanical bond to poured concrete• Can be installed regardless of ambient or surface temperatures• VOC-free• Mapeproof membranes are not affected if the level of the water table

rises and falls. • The needle-punched pattern in the geotextile fabrics guarantees that

the sodium bentonite is held firm and stable, even when applied vertically.

Applications:• Waterproofing for new and rehabilitation projects• Below-grade vertical and horizontal foundation structures• Cast-in-place concrete applications, including backfilled concrete

walls• Underground tunnels with earth-covered roofs• Below concrete slabs and elevator pits• Blindside applications, including soldier piles, lagging, steel sheet

piling, secant piles, shotcrete and stabilized soil-retention walls

The Mapeproof waterproofing system includes:• Mapeproof HW and Mapeproof SW waterproofing membranes.• Mapeproof Sealant for detailing and penetrations.• Mapeproof Granules for detailing and penetrations.• Idrostop ™ 25 and Idrostop B25 expandable waterstops.• Mapedrain ™ drainage composites, which create a consistent plane for

the Mapeproof membrane and channel water away from the structure.

Mapeproof warranties:MAPEI offers a variety of product and system warranty programs. Contact your local MAPEI representative for warranty information on your project.

For more information on the Mapeproof waterproofing system, including installation instructions and CAD details, please visit www.mapei.com.

Idrostop 25 is an expandable, flexible waterstop that features an acrylic polymer base and is used to create watertight

concrete joints.


Mapethene warranties:MAPEI offers a variety of product and system warranty programs. Contact your local MAPEI representative for warranty information on your project.

For more information on the Mapethene waterproofing system, including installation instructions and CAD details, please visit www.mapei.com.

Sel f-Adher ing Sheet Waterproof ing Membranes

Self-Adhered Sheet Waterproofing MembranesMapethene HT and Mapethene LT are 60-mil-thick, self-adhering sheet waterproofing membranes composed of an impact-resistant, cross-laminated high density polyethylene (HDPE) film 4 mils thick, which is laminated onto a proprietary rubberized asphalt 56 mils thick.

Features and benefits:• Factory-produced products ensure a controlled thickness• Ideal waterproofing for new and rehabilitation projects• High hydrostatic head pressure resistance• Easy to apply, requiring no special tools or equipment • Fully adhered membrane, eliminating the potential for water migration

behind the membrane• Elastomeric nature of the membrane allows for the normal expansion

and contraction of the structure.• Wide application temperature window: – Mapethene HT = Ambient and substrate temperatures of 40°F

(5°C) and above – Mapethene LT = Ambient and substrate temperatures of 25°F

to 60°F (-4°C to 16°C) • Compatible with common construction materials such as concrete,

concrete masonry units (CMUs), metal, wood (pressure-treated and fire treated), rigid insulation and insulated concrete forms (ICF)

Applications:• Used for vertical and horizontal waterproofing on structural

foundation walls and decks• Can be used on below-grade foundation walls, tunnels, balconies,

split slabs, plaza decks, parking decks and bridges • Good for interior applications such as bathrooms, kitchens,

mechanical rooms and laboratories

The Mapethene waterproofing system includes: • Mapethene HT or Mapethene LT waterproofing membrane. • Mapebond 700 solvent-based, fast-drying contact adhesive.• Mapebond 710 low-VOC, solvent-based, fast drying contact adhesive.• Mapebond 720 water-based, contact adhesive.• Mapeflex ™ P2 NS and Mapeflex P1 for detailing and penetrations.• Mapethene Mastic for sealing terminations.• Mapedrain ™ drainage composites, to protect the Mapethene

membrane and to filter and channel water away from the structure.• Idrostop™ 25 and Idrostop B25 expandable waterstops.

Mapethene™ HT and Mapethene LT


Prefabr icated Drainage Composi tes

Drainage Composites, Foundation Perimeter Drain and FittingsTwo critical components of virtually all waterproofing systems are the abilities to protect the waterproofing membrane and channel water away from the structure. The proper drainage composite can protect the waterproofing membrane from accidental punctures that may occur, especially when backfilling. It also relieves hydrostatic pressure over the life of the waterproofing system. To meet the needs of various construction applications, MAPEI offers seven distinct drainage composites in addition to four drain fittings, all designed to ensure proper building drainage.

Product construction:MAPEI’s Mapedrain drainage composites are composed of a three-dimensional, polypropylene core, which has significantly greater chemical resistance than other products on the market that use polystyrene or other polymeric materials. Each core has a polypropylene geotextile fabric, either woven or nonwoven (depending upon application requirements) heat-welded to the top of the dimples; this fabric retains soil/concrete and filters out any debris that could clog the water channels created by the three-dimensional core. Because filter fabrics are heat-welded to the core, a process far superior to “gluing” them, they have a greater ability to stay in place during backfill or overburden placement. In addition, the polypropylene cores of all Mapedrain products contain at least 40% post-industrial recycled content.

Mapedrain 10 is a basic, single-sided drainage composite for low-depth (< 10 ft. [3.05 m]) foundation walls and is typically used in residential and light commercial construction.

Compressive strength 11,000 psf (527 kN/m2)

Maximum flow rate 18 g/min/ft (223 L/min/m)

Geotextile fabric Nonwoven

Core thickness 0.40" (10.16 mm)

Mapedrain 20 is the standard for high-flow, high-compressive-strength, vertical, single-sided below-grade drainage.





Mapedrain 25 provides the same high level of performance as Mapedrain 20, with the addition of a backer film to prevent the potential for “die cutting” of a waterproofing membrane that is installed behind the drainage composite.





Mapedrain 30 is designed for horizontal applications that demand very high compressive strength and flow rates. Its woven filter fabric allows concrete to be poured directly on top of the drainage composite.

Compressive strength 21,000 psf (1 005 kN/m2)


Geotextile fabric Woven


Mapedrain 40 provides the same high level of performance as Mapedrain 30, but can be used in both vertical and horizontal applications. Additionally, the nonwoven filter fabric used in the construction of Mapedrain 40 is unmatched in its ability to prevent particulates from entering, and potentially clogging, the drainage channel.





Mapedrain™ and fittings

Mapedrain™ 10

Mapedrain™ 20

Mapedrain™ 25

Mapedrain™ 30

Mapedrain™ 40


Prefabr icated Drainage Composi tes

Mapedrain 50 provides the ultimate in compressive strength and flow rate. Like Mapedrain 30, Mapedrain 50 is designed for horizontal applications and utilizes a woven filter fabric, so that concrete can be poured directly on top of the drainage composite. It is typically used in applications where the forces of heavy vehicular traffic will be encountered.



Geotextile fabric Woven


Mapedrain TD Fittings aid in controlling the water discharged from a Mapedrain system, which includes Mapedrain TD Drainage Composite as the “footing drain.” MAPEI offers four fittings designed to direct and release the cumulative water being discharged from the system:

• Mapedrain TD splice fitting• Mapedrain TD corner fitting• Mapedrain TD side outlet fitting• Mapedrain TD end outlet fitting

Mapedrain warranties:MAPEI offers a variety of product and system warranty programs. Contact your local MAPEI representative for warranty information on your project.

For more information on the Mapedrain waterproofing system, including installation instructions and CAD details, please visit www.mapei.com.

Mapedrain TD Drainage Composite is typically used to replace the traditional “French drain” foundation drainage system. Mapedrain TD Drainage Composite is used to collect high volumes of water, most commonly around footings where wall drainage composites discharge their water. It provides two-sided drainage with a nonwoven filter fabric.




Core thickness 1" (2.5 cm)

Mapedrain™ 50

Mapedrain™ TD FittingsMapedrain™ TD Drainage Composite


Waterproof ing Accessor ies

WATERPROOFING ACCESSORIES

Waterproofing is a system, not a product. As such, when designing and installing a waterproofing system for a structure, one must consider the performance and quality of the primary waterproofing membrane as well as of the accessory products that support it. Often, these attributes affect the most critical areas, such as penetrations, terminations and transitions.

MAPEI draws on its history of 80 years of producing concrete system accessories that are not only installer-friendly, thus increasing the likelihood for a successful installation, but that will also stand up to the test of time.

For more information on any of these products, including Technical Data Sheets, CAD details and more, please visit www.mapei.com.

Contact adhesivesMAPEI offers the four best contact adhesives for waterproofing systems in the industry. All of these contact adhesives promote adhesion between various waterproofing products and a variety of substrates, including concrete, wood, gypsum sheathing, metal and more.

* Consult all applicable federal, state and local laws and regulations regarding allowable VOC content, disposal and other product physical properties before selecting any contact adhesive.

Solvent-Based Contact AdhesiveMapebond 700 is an extremely quick-drying, solvent-based, high-tack contact adhesive.

Features and benefits:• Extremely quick drying time• Aggressive tack improves adhesion of waterproofing membranes• Ready to use; no mixing or dilution required• For vertical and horizontal applications• Wide temperature application window

Low-VOC Solvent-Based Contact AdhesiveMapebond 710 is a very quick-drying, solvent-based, high-tack contact adhesive.

Features and benefits:• The low content of VOCs (volatile organic compounds) is < 250 g/L,

which is compliant with most state and local VOC requirements for adhesives and sealants. Note: Be sure to check all applicable regulations, based on the project location.

• Very quick drying time• Aggressive tack improves adhesion of waterproofing membranes• Ready to use; no mixing or dilution required• For vertical and horizontal applications• Wide temperature application window

Water-Based Contact AdhesiveMapebond 720 is a quick-drying, water-based, high-tack contact adhesive.

Features and benefits:• Water-based; nonflammable• Low odor• Quick-drying• Aggressive tack improves adhesion of waterproofing membranes• Ready to use; no mixing or dilution required• For vertical and horizontal applications

Mapebond™ 700

Mapebond™ 710

Mapebond™ 720


Rubberized-Asphalt Waterproofing Detailing MasticMapethene Mastic is solvent-based, rubberized-asphalt mastic that provides excellent adhesion to the Mapethene waterproofing membranes as well as to structural concrete, masonry and wood surfaces. Mapethene Mastic is used as a secondary seal on seams, T-joints, laps, penetrations, terminations and other detailing areas on the top surface and edges of Mapethene waterproofing membranes. Mapethene Mastic should never be used underneath the waterproofing membrane.

Extruded Polystyrene Fanfold Protection BoardMapecover 810 is a rigid, lightweight, extruded polystyrene (XPS), fanfold protection board designed to protect MAPEI waterproofing membranes on vertical below-grade foundations during the placement of backfill and over horizontal waterproofing applications, to protect the membrane from other trades. Mapecover 810 can also be used in planters, as a vertical protection course for MAPEI waterproofing membranes.

Hydro-Expansive WaterstopIdrostop 25 is an expandable, flexible waterstop with an acrylic polymer base that is used to create watertight concrete joints. Idrostop 25 is also used as a detailing accessory in conjunction with all MAPEI waterproofing membrane systems. When Idrostop 25 comes into contact with moisture, it expands to fill voids and form a positive seal with the concrete. Idrostop 25 can be used in standard applications and where contaminated or salt groundwater may be encountered.

Bentonite-Based, Hydrophilic, Expandable, Flexible Rubber Waterstop Strip for Watertight ConstructionIdrostop B25 is an expandable, flexible waterstop with sodium bentonite and a polymer base that is used to create watertight concrete joints. Idrostop B25 can also be used as a detailing accessory in conjunction with all MAPEI waterproofing membrane systems. When Idrostop B25 comes into contact with moisture, it expands to fill voids and forms a positive seal with the concrete.

Sodium Bentonite GranulesMapeproof Granules are sodium bentonite clay granules used as a detailing accessory in conjunction with Mapeproof HW and Mapeproof SW waterproofing membranes. When Mapeproof Granules come into contact with moisture, they form into a dense, low-permeable gel that, when combined with Mapeproof HW or Mapeproof SW waterproofing membrane, produces a seamless waterproofing system.

Detailing Sealant for Mapeproof HW and Mapeproof SWMapeproof Sealant is a trowel-grade sealant, composed of sodium bentonite clay and specially designed polymers, that is used as a detailing accessory in conjunction with Mapeproof HW and Mapeproof SW waterproofing membranes. When Mapeproof Sealant comes into contact with moisture, it swells to seal against water intrusion. Mapeproof Sealant is easily applied and bonds to most substrates. When used with Mapeproof HW or Mapeproof SW, Mapeproof Sealant forms a seamless waterproofing system.

Two-Component, Non-Sag, Polyurethane SealantMapeflex P2 NS is a two-component, non-sag, polyurethane elastomeric sealant that offers excellent adhesion to most surfaces, features faster curing than traditional one-component polyurethane sealants and meets the requirements of ASTM C920.

One-Component, Non-Sag, Elastomeric Polyurethane SealantMapeflex P1 is a high-performance, one-component, elastomeric, moisture-cured, polyurethane sealant and adhesive. Mapeflex P1 offers excellent adhesion to most surfaces, superior gunning/tooling and excellent flexibility for moving joints.

Detailing accessories

Mapethene™ Mastic

Mapecover™ 810

Idrostop™ 25

Idrostop™ B25

Mapeproof™ Granules

Mapeproof™ Sealant

Mapeflex™ P2 NS

Mapeflex™ P1



Flexible Waterproofing Tape for Moving JointsMapeband TPE is a professional-grade, highly durable and flexible band tape used to waterproof expansion and other dynamic joints subject to movement of 2" to 4" (5 to 10 cm). TPE, an acronym for “elastomeric thermoplastic polyolefin,” represents a group of polyolefins that combine the best properties of thermoplastic polymers and synthetic elastomer technology. Measuring 47.2 mils thick and reinforced sidelong with polyester nonwoven fabric, Mapeband TPE tape must be bonded in place with Planibond ® AE. Mapeband TPE is offered in two versions: Mapeband TPE 170 measures 6.7" (17 cm) wide, while Mapebond TPE 325 measures 12.8" (32.5 cm) wide.

High-Strength, Non-Sag, Epoxy Anchoring GelPlanibond AE is a high-strength, two-part, non-sag, epoxy anchoring gel designed for a wide variety of bonding and repair applications. Planibond AE is used to bond Mapeband ™ TPE in place, but can also be used to anchor bolts, dowels and pins in concrete or masonry.

Liquid Membrane Reinforcing FabricMAPEI LMR Fabric is a spunbond, nonwoven polyester fabric used as a reinforcement for liquid-applied waterproofing membranes. When embedded into a liquid-applied waterproofing membrane, it will add strength and durability to the overall system.

Mapeband™ TPE

Planibond ® AEMAPEI LMR Fabric



Sur face-Preparat ion Products

Cement-Based Dampproofing CoatingPlaniseal 88 is a one-component, polymer-modified, cementitious dampproofing coating. It can be used on horizontal, vertical and overhead surfaces such as walls, retaining walls, planters, beams and other applications to provide an appropriate surface to receive a waterproofing membrane. It can be mixed with potable water or, for superior bonding performance, Planicrete ® AC diluted with water.

One-Component, Fast-Setting, Fiber-Reinforced, Vertical and Overhead Repair MortarPlanitop X is a one-component, fiber-reinforced, shrinkage-compensated, high-early-strength, fast-setting, polymer-modified, high-build cementitious repair mortar with a corrosion inhibitor. It is suited for all interior/exterior vertical and overhead concrete repairs, including precast/prestressed, tilt-up, post-tensioned and cast-in-place concrete. Planitop X can be applied from featheredge to 4" (10 cm) per lift. Planitop X is engineered to provide high early strength with ease of application. Planitop X dries to a light gray color, matching most concrete surfaces.

Planitop X is ideal for repairing defects in concrete surfaces, such as the filling of honeycombs, voids and cavities. Planitop X is a very fast-setting product, with a working time of 5 to 6 minutes, providing an initial set at 6 minutes and final set in less than 25 minutes. Planitop X can be mixed with potable water or, for superior bonding performance, with Planicrete ® AC diluted with water.

One-Component, Fast-Setting, Extended-Working-Time, Vertical and Overhead Repair MortarPlanitop XS is an extended-working-time variation of Planitop X. Shrinkage-compensated, fiber-reinforced, polymer-modified and containing a proprietary corrosion inhibitor, Planitop XS features Planitop X ’s outstanding workability and versatility. Ideal for a wide variety of vertical and overhead concrete repairs, Planitop XS can be applied from featheredge to 4" (10 cm) per lift. Planitop XS dries to a light gray color, blending well with most concrete surfaces.

Planitop XS is ideal for repairing defects in concrete surfaces, such as the filling of honeycombs, voids and cavities. With Planitop XS, working time is extended to 20 minutes, providing an initial set at 40 minutes and final set in less than 60 minutes. Like Planitop X, Planitop XS can be mixed with potable water or, for superior bonding performance, with Planicrete ® AC diluted with water.

Acrylic Latex Admixture for Mortar and ConcretePlanicrete AC is a one-component, concentrated, liquid latex admixture used to enhance the performance of cementitious repair mortars, plasters, stuccos, concrete mixes and toppings for the restoration of horizontal, vertical and overhead concrete; concrete masonry units (CMUs); and masonry surfaces.

Planicrete AC can be used as an accessory with Planiseal ® 88, Planitop ® X and Planitop XS to enhance the bond strength to existing concrete.

SURFACE-PREPARATION PRODUCTS

For any waterproofing system to function properly, it must be attached to a substrate that is structurally sound and crack-free with a surface profile appropriate for the waterproofing system being employed. While basic surface preparation, such as the removal of laitance and mortar joints being struck flush, remains essential, MAPEI offers the following products for when additional surface preparation is required.

For more information on any of these products, including Technical Data Sheets, CAD details and more, please visit www.mapei.com.

Planiseal ® 88

Planitop® XPlanitop® XS

Planicrete® AC

Planitop X

Planitop XS

MAPEI’s waterproofing tools for architects are available online

MAPEI offers Waterproofing Systems in the Architectural CAD/Spec Guide tool on its website. Users have easy access to Guide Specifications for the waterproofing systems, Technical Data Sheets and over 100 CAD details (available in DWG and PDF formats).

MAPEIBentonite

Waterproofing–G

eosyntheticClay

Liner071700

-page1

version201606

17

MANUFACTURER’S GUIDE SPECIFICATION

SECTION 07 17 00 Bentonite Waterproofing – Geosynthetic Clay Liner (GCL)

NOTES TO EDITOR:

Editor's Notes are in red font. Delete from final document.

Revise this Section by deleting and inserting text to meet Project’s specific requirements.

Bentonite waterproofing Geosynthetic Clay Liners can be used on both positive side and blind side for

both vertical and horizontal structural foundation walls and under slab on grade. Applicable for below-

grade foundation walls, retaining walls, elevator pits, tunnels, earth covered structures, under slabs,

lagging walls, secant piles, and sheet piles. Do not use when membrane exposed to continuous sunlight.

Not recommended for pond and tank liner applications except for between slab applications.

PART 1 – GENERAL

1.1 RELATED DOCUMENTS

A. All Contract Documents, including General and Supplementary Conditions, and Division

1 General requirements, apply to this section.

1.2 SUMMARY

A. Section includes complete waterproofing system, preparation of substrate, and

prefabricated drainage composite system to prevent passage of liquid water into building

structure. Compatible with construction materials such as concrete, shotcrete, and metal.

Includes protection.

NOTES TO EDITOR: Include rigid board insulation as required.

1.3 SYSTEM DESCRIPTION

A. Waterproofing system includes:

1. Verification of Waterstop in construction joints.

NOTES TO EDITOR: Although waterstop is specified in 03 15 00, it is a critical

prerequisite for Bentonite Waterproofing Warranty and performance.

2. Substrate preparation repair mortars, cants/fillet, crack filler and joint treatment.

3. Waterproofing shall be composed of granular sodium bentonite clay at a rate of

1.13 lbs. per sq. ft. (5,5 kg per m2) sandwiched between two polypropylene

geotextile fabrics – a nonwoven and a woven fabric. The nonwoven fabric is

MAPEI Headquarters of North America1144 East Newport Center Drive Deerfield Beach, Florida 33442 1-888-US-MAPEI (1-888-876-2734) / (954) 246-8888

Technical Services1-888-365-0614 (U.S. and Puerto Rico) 1-800-361-9309 (Canada)

Customer Service1-800-42-MAPEI (1-800-426-2734)

Services in Mexico0-1-800-MX-MAPEI (0-1-800-696-2734)

Copyright ©2019 by MAPEI Corporation (“MAPEI”) and all rights are reserved. All intellectual property rights and other information contained in this document are the exclusive property of MAPEI (or its parent or related companies), unless otherwise noted. No part of this document may be reproduced or transmitted in any form without the prior written consent of MAPEI.

Edition Date: January 1, 2019

PR: 9033 MKT: 18-2405 Printed in the USA.

MAPEI USA MAPEI Canada