Vostro 1520 Service Manual - Dell · 2013. 10. 25. · If your computer does not perform a Power -On Self -Test upon boot up, there are various things to look for: 1. ... 256 MB dedicated

Dell™ Vostro™ 1520 Service Manual

Notes, Cautions, and Warnings

If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows® operating systems are not applicable.

Information in this document is subject to change without notice. © 2009 Dell Inc. All rights reserved.

Reproduction of this material in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, Vostro, TravelLite, Wi-Fi Catcher, and ExpressCharge, are trademarks of Dell Inc.; Intel, Pentium, Celeron and Core are registered trademarks of Intel Corporation; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license; TouchStrip is a trademark of Zvetco Biometrics, LLC; Blu-ray Disc is a trademark of the Blu-ray Disc Association; Microsoft, Windows, Windows Vista, and the Windows Vista start button are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

May 2009 Rev. A00

Working on Your Computer

Adding and Replacing Parts

Specifications

Diagnostics

System Setup

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

file:///C:/data/systems/vos1520/en/SM/work.htmfile:///C:/data/systems/vos1520/en/SM/parts.htmfile:///C:/data/systems/vos1520/en/SM/specs.htmfile:///C:/data/systems/vos1520/en/SM/diags.htmfile:///C:/data/systems/vos1520/en/SM/bios.htm

Back to Contents Page

System Setup Dell™ Vostro™ 1520 Service Manual

Entering System Setup

Menu

Your computer's BIOS, or System Setup program allows you to do the following:

l Access System Setup by pressing l Bring up a one-time boot menu by pressing

Entering System Setup

Press to enter System Setup and make changes to the user-definable settings. If you are having trouble entering Setup using this key, reboot and press the key when the keyboard LEDs first flash.

Menu

Press when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the computer. The devices listed on the boot menu depend on the bootable devices installed in the computer.

l Internal HDD l CD/DVD/CD-RW Drive l Onboard NIC l BIOS Setup l Diagnostics (starts the Pre-boot System Assessment (PSA) diagnostics)

This menu is useful when attempting to boot to a particular device or to bring up the diagnostics for the computer. Using the boot menu does not make any changes to the boot order stored in the BIOS.

file:///C:/data/systems/vos1520/en/SM/index.htm


Diagnostics Dell™ Vostro™ 1520 Service Manual

Device Status Lights

LED Error Codes

Power Button Light Codes

Device Status Lights

If your computer is connected to an electrical outlet, the light operates as follows:

l Solid blue—The battery is charging. l Flashing blue—The battery is almost fully charged.

If your computer is running on a battery, the light operates as follows:

l Off—The battery is adequately charged, or the computer is turned off. l Flashing orange—The battery charge is low. l Solid orange—The battery charge is critically low.

LED Error Codes

If your computer does not perform a Power-On Self-Test upon boot up, there are various things to look for:

1. Check that the computer power light is on. 2. If the power light is not on, ensure that your computer is plugged into AC power. Remove the battery. 3. If your computer is powered on but is not performing a POST, check to see whether or not the keyboard status lights flash to indicate a successful POST

but no video or if the keyboard status lights are lit in a sequence indicating a system problem.

The following table shows the possible LED codes that may display in a no-POST situation.

Device status lights located in the center of the hinge cover.

1—Turns on when your computer reads or writes data to the hard drive.

NOTE: To avoid loss of data, never turn off your computer while the Hard Drive light is flashing.

2—Turns on when wireless networking is enabled.

3—Turns on when a card with Bluetooth® wireless technology is enabled.

NOTE: The card with Bluetooth wireless technology is an optional feature, so the light turns on only if you ordered the card with your computer. For more information, see the documentation that came with your card.

To turn off only the Bluetooth wireless technology functionality, right-click the icon in the system tray and click Disable Bluetooth Radio.

4—Turns on when the numeric keypad is enabled.

5—Turns on when the uppercase letter function is enabled.

6—Turns on when the scroll lock function is enabled.

Appearance Description Next Step

ON-FLASH-FLASH

No SODIMMs are installed

1. Install supported memory modules. 2. If memory is already present, reseat the module(s) one at

time in each slot. 3. Try known good memory from another computer or replace the

memory. 4. Replace the system board.

FLASH-ON-ON

System board error

1. Reseat the processor. 2. Replace the system board. 3. Replace the processor.

FLASH-ON-FLASH

LCD Panel Error

1. Reseat the LCD cable. 2. Replace the LCD panel. 3. Replace the video card / system board.

OFF-FLASH-OFF 1. Install compatible memory modules.

file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htm

Power Button Light Codes

The power LED located in the power button on the front of the computer illuminates and blinks or remains solid to indicate five different states:

l No light—System is in the off state (S5, or mechanical (AC power not applied) OFF). l Solid Amber—System fault, but power supply is good—normal operating state (S0). l Blinking Amber—System fault error condition including Power Supply (only +5VSB working), Vreg failure, missing or bad CPU. l Blinking Green—System is in power saving states S1, S3 or S4. (Blink rate is 1Hz). No fault/error condition. l Solid Green—System is fully functional and is in S0 (ON) state.

Memory compatibility error

2. If two modules are installed remove one and test. Try the other module in the same slot and test. Test the other slot with both modules.

3. Replace the memory. 4. Replace the system board.

ON-FLASH-ON

Memory is detected but has errors

1. Reseat the memory. 2. If two modules are installed remove one and test. Try the

other module in the same slot and test. Test the other slot with both modules.

3. Replace the memory 4. Replace the system board.

OFF-FLASH-FLASH

Modem Error

1. Reseat the modem. 2. Replace the modem. 3. Replace the system board.

FLASH-FLASH-FLASH

System board error1. Replace the system board.

FLASH-FLASH-OFF

Option ROM Error

1. Reseat the device. 2. Replace the device. 3. Replace the system board.

OFF-ON-OFF

Storage device error

1. Reseat the hard drive and optical drive. 2. Test the computer with just the hard drive and just the optical

drive. 3. Replace the device that is causing the failure. 4. Replace the system board.

FLASH-FLASH-ON

Video card error1. Replace the system board.


Adding and Replacing Parts Dell™ Vostro™ 1520 Service Manual

Battery

Hard Drive

Wireless Local Area Network (WLAN) Card

Optical Drive

Processor and Memory Access Panel

Heat Sink and Processork

Display Assembly

Camera

LCD Display Panel

Keyboard

USB/IEEE 1394 Board

Speaker Assembly

Coin-Cell Battery

Hard Drive and Mini-Card Access Panel

Wireless Wide Area Network (WWAN) Card

Internal Card With Bluetooth® Wireless Technology

Fan

Memory

Hinge Cover

Display Bezel

Display Assembly Hinges

Display Inverter

Palm Rest

Fingerprint Reader

System Board

file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_wlan.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htmfile:///C:/data/systems/vos1520/en/SM/td_fan.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htmfile:///C:/data/systems/vos1520/en/SM/td_proc.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_dcam.htmfile:///C:/data/systems/vos1520/en/SM/td_dpnl.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_usb.htmfile:///C:/data/systems/vos1520/en/SM/td_spkr.htmfile:///C:/data/systems/vos1520/en/SM/td_coin.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_wwan.htmfile:///C:/data/systems/vos1520/en/SM/td_wpan.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htmfile:///C:/data/systems/vos1520/en/SM/td_fan.htmfile:///C:/data/systems/vos1520/en/SM/td_mem.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_dbzl.htmfile:///C:/data/systems/vos1520/en/SM/td_dhng.htmfile:///C:/data/systems/vos1520/en/SM/td_dinv.htmfile:///C:/data/systems/vos1520/en/SM/td_palm.htmfile:///C:/data/systems/vos1520/en/SM/td_fngr.htmfile:///C:/data/systems/vos1520/en/SM/td_sysbd.htm


Specifications Dell™ Vostro™ 1520 Service Manual

Processor

System Information

ExpressCard™

8-in-1 Memory Card Reader

Memory

Connectors

Communications

Video

Audio

Display

Keyboard

Touch Pad

Fingerprint Reader

Camera

Battery

AC Adapter

Physical

Environmental

NOTE: Offerings may vary by region. For more information regarding the configuration of

your Tablet-PC, click Start (or Start in Windows XP)® Help and Support, and then select the option to view information about your Tablet-PC.

Processor

Processor type Intel® Core™ 2 Duo processors

L1 cache 32 KB per instruction, 32 KB data cache per core

L2 cache Shared 3 MB or 6 MB

External bus frequency 1067 MHz

System Information

System chipset Intel GM45 or Intel PM45 chipset

Data bus width 64 bits

DRAM bus width 64 bits

Processor address bus width 36 bits

Flash EPROM SPI 32 Mbit

PCI bus (discrete graphics only) x16 PCI Express

ExpressCard™ (optional)

NOTE: The ExpressCard slot is designed only for ExpressCards. It does NOT support PC cards.

ExpressCard connector ExpressCard slot (USB and PCI Express-based interfaces)

Cards supported 34-mm and 54-mm ExpressCards

Secure Digital (SD) Memory Card Reader

Cards supported SD, SDIO, SD HC, Mini SD (with adapter) MMC, MMC+, Mini MMC (with adapter)

Memory

Memory module connector Two DIMM sockets

Memory module capacities 1 GB (one DIMM), 2 GB (one DIMM or two DIMMs), 3 GB (2 DIMMs), 4 GB (2 DIMMs)

Memory type DDR2 800 MHz non-ECC memory only.

Minimum memory 1024 MB (1 GB)

Maximum memory 4096 MB (4 GB)

Connectors

Audio Microphone connector and stereo headphone/speakers

file:///C:/data/systems/vos1520/en/SM/index.htm

connector

IEEE 1394 One 4-pin -connector

Dock Optional USB Port Replicator only

Mini-card support (internal expansion slots) One dedicated half Mini-Card slot for WLAN One dedicated full Mini-Card slot for WPAN (Bluetooth® or ultra wideband [UWB]) WPAN full Mini-Card slot can also be used for the Intel Flash Cache

Modem Optional USB external modem

Network adapter RJ-45 connector

USB, USB PowerShare, eSATA Four 4-pin USB 2.0-compliant connectors

Video VGA

Communications

Modem External (optional)

Network adapter 10/100/1000 Ethernet LAN on system board

Wireless WLAN half Mini-Card, WPAN full Mini-Cards, Bluetooth® wireless support, and UWB technology

Mobile Broadband None

GPS None

Video

Video type Integrated Discrete on system board, hardware accelerated

Video controller Integrated video: Mobile Intel GMA X4500 Discrete video: NVIDIA GeForce 9300M GS

Data bus Integrated video or PCI-Express video x16

Video memory Integrated video: up to 256 MB shared Discrete video: 256 MB dedicated memory

Video output Video connector and multimode DisplayPort

Audio

Audio type Two-channel high-definition audio codec

Audio controller IDT 92HD71B5

Stereo conversion 24-Bit (stereo digital-to-analog) 24-Bit (stereo analog-to-digital)

Interfaces:

Internal Internal High Definition Audio

External Microphone-in connector, stereo headphones/speakers mini-connector

Speaker One 2-watt, 4-ohm speakers

Internal speaker amplifier 1-Watt channel into 4 ohms

Internal microphone Single digital microphone

Volume controls Volume control buttons

Display

Type (active-matrix TFT)15.4" WXGA w/anti-glare CCFL or WLED 15.4" WXGA+ w/anti-glare CCFL or WLED 15.4" WUXGA TrueLife!" CCFL

Dimensions

Height 225.5 mm (8.8 inches)

Width 344.5 mm (13.6 inches)

Diagonal 391.16 mm (15.4 inches)

Maximum Resolutions

WXGA w/anti-glare 1280x800 at 262 K colors

WXGA+ w/anti-glare 1440x900 at 262 K colors

WUXGA with TrueLife 1920X1200 at 262 K colors

Operating angle 0° (closed) to 160°

Refresh rate 60 Hz

Viewing angles

Horizontal ±40° (WXGA) typical ±40° (WXGA with TrueLife)

Pixel pitchWXGA –.258 mm (.010 inch) WXGA with TrueLife –.23 mm (.009 inch)

Controls Brightness can be controlled through keyboard shortcuts

Keyboard

Number of keys 84 (U.S. and Canada); 85 (Europe); 88 (Japan)

Layout QWERTY/AZERTY/Kanji

Size full sized (19-mm key pitch)

Touch Pad

X/Y position resolution (graphics table mode)

240 CPI

Size

Width 73.0-mm (2.9-inch) sensor-active area

Height 42.9-mm (1.7-inch) rectangle

Fingerprint Reader (Optional)

Type UPEK TCS3 TouchStrip™ strip sensor with CMOS active capacitive pixel-sensing technology

Camera (Optional)

Resolution 640 x 480 pixels (VGA)

Battery

Type

12-cell lithium-ion prismatic slice battery 84 WHr

9-cell lithium-ion battery 85 WHr



Dimensions:

Depth

4- or 6-cell lithium-ion battery 206 mm (8.11 inches)

9-cell lithium-ion battery 93.3 mm (3.67 inches)


Height

4- or 6-cell lithium-ion battery 19.8 mm (0.78 inch)

9-cell lithium-ion battery 22.3 mm (0.88 inch)

12-cell lithium-ion battery 217.24 mm (8.55 inch)

Width

4- or 6-cell lithium-ion battery 47.0 mm (1.85 inches)



Weight

4-cell lithium-ion battery 0.24 kg (0.53 lb)




Voltage

4-cell lithium-ion battery 14.8 VDC

6- or 9-cell lithium-ion battery 11.1 VDC

12-cell lithium-ion battery 14.8 VDC

Charge time (approximate)

Computer off

6-cell lithium-ion battery Approximately 1 hour to 80% capacity Approximately 2 hours to 100% capacity

Operating TimeVaries depending on operating conditions and can be significantly reduced under certain power-intensive conditions

Life span (approximate) 1 year

Temperature range

Operating 0°C to 40°C (32°F to 104°F)

Storage –10° to 65°C (14° to 149°F)

Coin-cell battery CR-2032

AC Adapter

Input voltage 100–240 VAC

Input current (maximum) 1.5 A

Input frequency 50–60 Hz

Temperature range:

Operating 0°C to 35°C (32° to 95°F)

Storage –40°C to 65°C ( –40° to 149°F)

PA-12 65-W Travel AC adapter:

Output voltage 19.5 V DC

Output current 3.34 A

Height 15 mm (0.6 inches)

Width 66 mm (2.6 inches)

Depth 127 mm (5.0 inches)

Weight 0.29 kg (0.64 lb)

PA-10 90-W D-Series AC adapter:







PA-3E 90 E-Series AC adapter:







Physical

Height Front: 26.2 (1.031 inches) Back: 38 mm (1.496 inches)



Weight (with 6-cell battery) 2.8 kg (6.173 lb)

Environmental

Temperature range:

Operating 0° to 35° C (32° to 95° F)

Storage –40° to 65° C (–40° to 149° F)

Relative humidity (maximum):

Operating 10% to 90% (non-condensing)

Storage 5% to 95% (non-condensing)

Maximum vibration (using a random-vibration spectrum that simulates user environment):

Operating 0.66 GRMS

Storage 1.30 GRMS

Maximum shock (measured with hard drive in head-parked position and a 2-ms half-sine pulse):

Operating 143 G

Storage 163 G

Altitude (maximum):

Operating –15.2 to 3048 m (–50 to 10,000 ft)

Storage –15.2 to 3048 m (–50 to 10,000 ft)


Battery Dell™ Vostro™ 1520 Service Manual

Removing the Battery

1. Follow the procedures in Before Working Inside Your Computer.

2. Slide the battery lock latch on the left away from the battery.

3. Slide the battery latch at the center toward the right..

WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#before

4. Slide the battery itself toward the back of the computer and remove.


Coin-Cell Battery Dell™ Vostro™ 1520 Service Manual

Removing the Coin-Cell Battery

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the processor and memory access panel from the computer. 4. Remove the fan from the computer. 5. Remove the heat sink and processor from the computer. 6. Remove the memory modules from the computer. 7. Remove the coin-cell battery from the computer. 8. Remove the hard drive and mini-card access panel from the computer. 9. Remove the hard drive from the computer.

10. Remove the optical drive from the computer. 11. Remove the Bluetooth module from the computer. 12. Remove any WLAN and WWAN cards from the computer. 13. Remove the hinge cover from the computer. 14. Remove the keyboard from the computer. 15. Remove the display assembly from the computer. 16. Remove the palm rest from the computer. 17. Remove the system board from the computer.

18. Set aside the chassis, and place the systemboard on a clean work surface.

19. Insert a plastic scribe into slot and gently pry up the coin-cell battery.

20. Remove the coin-cell battery.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htmfile:///C:/data/systems/vos1520/en/SM/td_fan.htmfile:///C:/data/systems/vos1520/en/SM/td_proc.htmfile:///C:/data/systems/vos1520/en/SM/td_mem.htmfile:///C:/data/systems/vos1520/en/SM/td_coin.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_wpan.htmfile:///C:/data/systems/vos1520/en/SM/td_wlan.htmfile:///C:/data/systems/vos1520/en/SM/td_wwan.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_sysbd.htm


Display Bezel Dell™ Vostro™ 1520 Service Manual

Removing the Display Bezel

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the display assembly from the computer.

3. Remove the six rubber screw covers from the display bezel.

4. Remove the six screws that secure the bezel to the display assembly.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_dsply.htm

5. Remove the bezel from the display assembly.


Camera Dell™ Vostro™ 1520 Service Manual

Removing the Camera

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the display assembly from the computer. 3. Remove the display bezel from the display assembly. 4. Remove the LCD display panel from the display assembly.

5. Loosen the captive screw that secures the display camera in place.

6. Lift the camera from its slot.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_dbzl.htmfile:///C:/data/systems/vos1520/en/SM/td_dpnl.htm

6. Release the display camera data cable from its clip and disconnect the display camera data cable.

7. Remove the display camera from the display assembly.


Display Assembly Hinges Dell™ Vostro™ 1520 Service Manual

Removing the Display Assembly Hinges

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the display assembly from the computer. 3. Remove the display bezel from the display assembly. 4. Remove the display inverter from the display assembly. 5. Remove the LCD display panel from the display assembly.

6. Remove the eight screws securing the hinges to the display panel assembly.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_dbzl.htmfile:///C:/data/systems/vos1520/en/SM/td_dinv.htmfile:///C:/data/systems/vos1520/en/SM/td_dpnl.htm

7. Slide the hinges away from the display panel assembly.

8. Remove the display panel hinges from the display panel assembly.


Display Inverter Dell™ Vostro™ 1520 Service Manual

Removing the Display Inverter

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the display assembly from the computer.

3. Remove the screw that secures the display inverter to the display assembly.

4. Open the display inverter data cable clip.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_dsply.htm

5. Remove the display inverter data cable from the clip.

6. Disconnect the data cable from the display inverter.

7. Remove the display inverter from the display assembly.


LCD Display Panel Dell™ Vostro™ 1520 Service Manual

Removing the LCD Display Panel

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the display assembly from the computer. 3. Remove the display bezel from the display assembly.

4. Remove the two screws that secure the LCD display panel to the display assembly.

5. Remove the LCD display panel from the display assembly.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_dbzl.htm


Display Assembly Dell™ Vostro™ 1520 Service Manual

Removing the Display Assembly

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Remove the hinge cover from the computer. 5. Remove the keyboard from the computer. 6. Remove the hard drive from the computer. 7. Remove the optical drive from the computer.

8. Disconnect the antenna cables from the WLAN card.

9. Disconnect the camera cable from the system board.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htm

10. Disconnect the display data cable from the system board.

11. Carefully draw the antenna cables through the system board.

12. Remove the antenna cables from their routing slots.

13. Remove the display data cable from its routing slot.

14. Remove the four screws that secure the display assembly to the base of the computer.

15. Remove the four screws that secure the display assembly to the base of the computer.


Fan Dell™ Vostro™ 1520 Service Manual

Removing the Fan

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the processor and memory access panel from the computer.

4. Disconnect the fan cable from the system board.

5. Remove the three screws that secure the fan to the computer.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htm

6. Lift the fan and remove it from the computer.


Fingerprint Reader Dell™ Vostro™ 1520 Service Manual

Removing the Fingerprint Reader

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Remove the hard drive from the computer. 5. Remove the WLAN card from the computer. 6. Remove the hinge cover from the computer 7. Remove the keyboard from the computer. 8. Remove the display assembly from the computer. 9. Remove the palm rest from the computer.

10. Remove the screw that secures the fingerprint reader retention plate to the computer chassis.

11. Slide the fingerprint reader retention plate to the left.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_wlan.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_palm.htm

12. Remove the fingerprint reader retention plate.

13. Open the fingerprint cable retention clip.

14. Remove the fingerprint cable from the retention clip.

15. Remove the fingerprint reader from the palm rest.


Hinge Cover Dell™ Vostro™ 1520 Service Manual

Removing the Hinge Cover

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer.

3. Use a plastic scribe gently to pry the back side of the hinge cover away from the base of the computer.

4. Starting on the right side, separate the hinge cover from the base of the computer.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htm

5. Continue to separate the hinge cover from the computer working from right to left, then remove the hinge cover.


Hard Drive Dell™ Vostro™ 1520 Service Manual

Removing the Hard Drive

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer.

4. Slide the hard drive toward the side of the computer.

5. Lift and remove the hard drive from the computer.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htm


Hard Drive and Mini-Card Access Panel Dell™ Vostro™ 1520 Service Manual

Removing the Hard Drive and Mini-Card Access Panel


3. Remove the two screws that secure the hard drive and mini-card access panel to the computer.

4. Slide the panel toward the rear of the computer.



5. Remove the hard drive and mini-card access panel.


Keyboard Dell™ Vostro™ 1520 Service Manual

Removing the Keyboard

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hinge cover from the computer.

4. Remove the two screws that secure the keyboard to the computer.

5. Lift the back edge of the keyboard slightly and slide the keyboard toward the back of the computer.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htm

6. Open the keyboard data cable clip to free the ribbon cable.

7. Remove the keyboard data cable from the clip.

8. Remove the keyboard from the computer.


Memory Dell™ Vostro™ 1520 Service Manual

Removing Memory Modules


4. Using your fingertips, carefully spread apart the securing clips on each end of the memory module connector until the memory module pops up.


NOTE: DIMM A is the module closest to the system board. You cannot remove DIMM A until DIMM B is removed. If only 1 DIMM is installed, it should always be installed in the DIMM A slot. If only 1 DIMM is installed, moving memory from DIMM A to DIMM B will disable AMT (if currently enabled).


5. Remove the memory module from the socket.


Optical Drive Dell™ Vostro™ 1520 Service Manual

Removing the Optical Drive


4. Remove the screw that secures the optical drive in place.

5. Insert a plastic scribe into the notch and slide the optical drive slightly out of the computer.



6. Remove the optical drive from the computer.


Palm Rest Dell™ Vostro™ 1520 Service Manual

Removing the Palm Rest

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Remove the hard drive from the computer. 5. Remove the optical drive from the computer. 6. Remove the keyboard from the computer. 7. Remove the display assembly from the computer. 8. Remove the processor and memory access panel from the computer.

9. Remove the thirteen screws that secure the palm rest to the bottom of the computer.

10. Turn over the computer and release the fingerprint reader data cable clip.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htm

11. Remove the fingerprint reader data cable from the clip.

12. Release the touch pad data cable clip.

13. Remove the touch pad data cable from the clip.

14. Remove the four screws that secure the palm rest to the top of the computer.

15. Disconnect the speaker cable from the system board.

16. Remove the palm rest from the computer.


Processor and Memory Access Panel Dell™ Vostro™ 1520 Service Manual

Removing the Processor and Memory Access Panel


3. Loosen the two captive screws on the access panel.

4. Lift the right side of the access panel.



5. Remove the access panel.


Heat Sink and Processor Dell™ Vostro™ 1520 Service Manual

Removing the Heat Sink and Processor

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the processor and memory access panel from the computer. 4. Remove the fan from the computer.

5. Loosen the six captive screws that secure the heat sink to the system board.

6. Lift the edge of the heat sink that is closest to the center of the computer.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htmfile:///C:/data/systems/vos1520/en/SM/td_fan.htm

7. Slide the heat sink toward the center of the computer, then lift up the heat sink and remove it from the computer.

8. Rotate the processor cam counterclockwise.

9. Lift the processor straight up from its socket, taking care not to bend any of the processor pins.


Speaker Assembly Dell™ Vostro™ 1520 Service Manual

Removing the Speaker Assembly

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Remove the hard drive from the computer. 5. Remove the optical drive from the computer. 6. Remove the WLAN card from the computer. 7. Remove the hinge cover from the computer. 8. Remove the keyboard from the computer. 9. Remove the display assembly from the computer.

10. Remove the palm rest from the computer and place it on a clean work surface.

12. Remove the four screws that secure the speaker assembly to the palm rest.

13. Lift the speakers from their slots, then remove the speaker assembly from the computer.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htmfile:///C:/data/systems/vos1520/en/SM/td_wlan.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_palm.htm


System Board Dell™ Vostro™ 1520 Service Manual

Removing the System Board

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove any ExpressCards and SD cards from the computer. 3. Remove the battery from the computer. 4. Remove the processor and memory access panel from the computer. 5. Remove the fan from the computer. 6. Remove the heat sink and processor from the computer. 7. Remove the memory modules from the computer. 8. Remove the coin-cell battery from the computer. 9. Remove the hard drive and mini-card access panel from the computer.

10. Remove the hard drive from the computer. 11. Remove the optical drive from the computer. 12. Remove the Bluetooth module from the computer. 13. Remove any WLAN and WWAN cards from the computer. 14. Remove the hinge cover from the computer. 15. Remove the keyboard from the computer. 16. Remove the display assembly from the computer. 17. Remove the palm rest from the computer.

18. Disconnect the first data cable from the system board.

19. Disconnect the second data cable from the system board.

WARNING: Before working inside your Tablet-PC, read the safety information that shipped with your Tablet-PC. For additional safety best practices information, see the Regulatory Compliance Homepage at www.dell.com/regulatory_compliance.

file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htmfile:///C:/data/systems/vos1520/en/SM/td_fan.htmfile:///C:/data/systems/vos1520/en/SM/td_proc.htmfile:///C:/data/systems/vos1520/en/SM/td_mem.htmfile:///C:/data/systems/vos1520/en/SM/td_coin.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htmfile:///C:/data/systems/vos1520/en/SM/td_wpan.htmfile:///C:/data/systems/vos1520/en/SM/td_wlan.htmfile:///C:/data/systems/vos1520/en/SM/td_wwan.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_palm.htm

20. Remove the three screws that secure the system board to the computer chassis.

21. Remove the system board from the computer chassis.


USB/IEEE 1394 Board Dell™ Vostro™ 1520 Service Manual

Removing the USB/IEEE 1394 Board

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the processor and memory access panel from the computer. 4. Remove the fan from the computer. 5. Remove the hard drive and mini-card access panel from the computer. 6. Remove the hard drive from the computer. 7. Remove the optical drive from the computer. 8. Remove the hinge cover from the computer. 9. Remove the keyboard from the computer.

10. Remove the display assembly from the computer. 11. Remove the palm rest from the computer.

12. Remove the screw that secures the USB/1394 connector board to the computer chassis.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_ppan.htmfile:///C:/data/systems/vos1520/en/SM/td_fan.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_opthd.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_palm.htm

13. Lift the USB/1394 connector board from its slot.

14. Disconnect the data cable from the USB/1394 connector board.

15. Lift the inside edge of the USB board and remove the board from the computer.


Wireless Local Area Network (WLAN) Card Dell™ Vostro™ 1520 Service Manual

Removing the WLAN Card

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Disconnect the antenna cables from the WLAN card.

5. Remove the screw that secures the WLAN card to the system board.

6. Remove the WLAN card from the computer.




Internal Card With Bluetooth® Wireless Technology Dell™ Vostro™ 1520 Service Manual

Removing the Internal Card With Bluetooth Wireless Technology

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Remove the hard drive from the computer. 5. Remove the WLAN card from the computer. 6. Remove the hinge cover from the computer. 7. Remove the keyboard from the computer. 8. Remove the display assembly from the computer. 9. Remove the palm rest from the computer.

10. Remove the screw that secures the Bluetooth module to the system board.

11. Lift the edge of the Bluetooth module closest to the front of the computer and lift the module from its slot.


file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htm#beforefile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hpan.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htmfile:///C:/data/systems/vos1520/en/SM/td_wlan.htmfile:///C:/data/systems/vos1520/en/SM/td_hcvr.htmfile:///C:/data/systems/vos1520/en/SM/td_key.htmfile:///C:/data/systems/vos1520/en/SM/td_dsply.htmfile:///C:/data/systems/vos1520/en/SM/td_palm.htm

12. Disconnect the data cable from the Bluetooth module.

13. Remove the Bluetooth module from the computer.


Wireless Wide Area Network (WWAN) Card Dell™ Vostro™ 1520 Service Manual

Removing the WWAN Card

1. Follow the procedures in Before Working Inside Your Computer. 2. Remove the battery from the computer. 3. Remove the hard drive and mini-card access panel from the computer. 4. Disconnect the antenna cables from the WWAN card.

5. Remove the screw that secures the WWAN card to the system board.

6. Remove the WWAN card from the computer.




Working on Your Computer Dell™ Vostro™ 1520 Service Manual

Before Working Inside Your Computer

Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions exist:

l You have performed the steps in Working on Your Computer. l You have read the safety information that shipped with your computer. l A component can be replaced or—if purchased separately—installed by performing the removal procedure in reverse order.

To avoid damaging your computer, perform the following steps before you begin working inside the computer.

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched. 2. Turn off your computer (see Turning Off Your Computer). 3. If the computer is connected to a docking device (docked) such as the optional Media Base or Battery Slice, undock it.

4. Disconnect all network cables from the computer. 5. Disconnect your computer and all attached devices from their electrical outlets. 6. Close the display and turn the computer upside-down on a flat work surface.

7. Remove the main battery (see Removing the Battery). 8. Turn the computer top-side up. 9. Open the display.

10. Press the power button to ground the system board.

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots. 12. Remove the hard drive (see Removing the Hard Drive).

Recommended Tools

The procedures in this document may require the following tools:

l Small flat-blade screwdriver l #0 Phillips screwdriver l #1 Phillips screwdriver l Small plastic scribe l Flash BIOS update program CD

Turning Off Your Computer

Before Working Inside Your Computer

Recommended Tools

Turning Off Your Computer

After Working Inside Your Computer


CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not covered by your warranty.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in this document.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.

CAUTION: To avoid damaging the system board, you must remove the main battery before you service the computer.

CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display.

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal components.

CAUTION: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

file:///C:/data/systems/vos1520/en/SM/index.htmfile:///C:/data/systems/vos1520/en/SM/work.htmfile:///C:/data/systems/vos1520/en/SM/td_batt.htmfile:///C:/data/systems/vos1520/en/SM/td_hdd.htm

1. Shut down the operating system: l In Windows Vista:

Click Start , then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down.

l In Windows XP:

Click Start® Turn Off Computer® Turn Off.

The computer turns off after the operating system shutdown process is complete.

2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for about 4 seconds to turn them off.

After Working Inside Your Computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer.

1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard. 2. Connect any telephone or network cables to your computer.

3. Replace the battery. 4. Connect your computer and all attached devices to their electrical outlets. 5. Turn on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers.

CAUTION: To connect a network cable, first plug the cable into the network device and then plug it into the computer.
file:///C:/data/systems/vos1520/en/SM/td_batt.htm

Documents

Vostro 1520 Service Manual - Dell · 2013. 10. 25. · If your computer does not perform a Power -On Self -Test upon boot up, there are various things to look for: 1. ... 256 MB dedicated