WELCOME TO THE BASIC MANUAL VOLCANO BOX

VOLCANO BOX PACKAGING CONTENTS1 x Volcano Box1 x Main cable to connect to the phone32 x jigs*1 x RX TX Cable*1 x A2B usb cable*

http://www.volcano-box.com/resellers.html

http://forum.gsmhosting.com/vbb/f723/ http://forum.gpgindustries.com/downloads.php?do=cat&id=164

http://www.volcano-box.com http://www.volcano-box.com/videos.htmlVolcano Box Official Resellers Volcano Box Homepage Volcano Box Video Help Center

Volcano Box Official Support Area Volcano Box Official Download Area

VOLCANO BOX DETAILS

This is power button use for power to box. When you want to use box on simple USB ( no need extra power) you must Un-press it means it must stay in Switched OFF Condition if you don’t want your box take power from usb then press it ( switch on Condition ) and Insert 9 Dc Volts in box then your box will not take current from USB. It will take all current from 9v

It’s for connecting Main cable to box so you can connect phones with main cable and main cable will connect with box. It’s 26 pin connector which can Auto pin find from 24 pins. Pin number 26 and 25 is VCC and GND fixed. You can also put VCC and GND on any pin which can defined from software

It’s for connect any RJ45 cable or you can use it for Test point Connection. You can connect any pin to any place. Volcano box can auto pin find from RJ45 Plug Too.

8PIN RJ45 FEMALE CONNECTOR

This is use for Connect Box with your Computer by use any USB Standard cable

This is for Connect any 9v Dc Adaptor. Positive inside and Negative out side

4 Power Light POWER LIGHT

USB FEMALE CONNECTOR

DC PIN FEMALE CONNECTOR

HOW TO SET-UP FOR THE FIRST TIME

Always check which is the Latest Version of your Volcano Box software. From where I can see ? Always check Official Download Area. Download it and install. if You installed 1st time or if your box is running 1st time then please make Sure you install Latest Box drivers before you plug your box. Where to get latest drivers. Please go to C:\Program Files\Volcano Team\VolcanoBox\Drivers\Box Drivers\New Box Drivers 1.5.2 and install it. After installation finished plug your box and let it install Drivers. When its installed make sure your box is not installed on high com port. For better results make sure your box is install on port number 3. After All Done Run Volcano Box software. Let it Update box firmware Automatically

AFTER IT`S COMPLETE IT WILL OPEN VOLCANO BOX SOFTWARE, IT WILL LOOK LIKE THIS

AFTER CLICK ON SIMPLE FORM ARROW AND CLICK ON ADVANCE FORM

AFTER THIS IT WILL SHOW LIKE THIS

AFTER THIS CLICK ON SYSTEM THENCLICK ON SYSTEM SELF CHECK

After this your Box is now Ready for RUN

Then Click on System Recovery Keep In mind You must Disconnect any Phone if connected with it and do this only on Latest Software of box. Don’t do this on old software versions !! and don’t do this every time. Just for once when you install your box VERY 1st time. If you play with it you can lose your box and we will not responsible as we told you already :D

Click on OK then wait till progress bar finished and its say to you

RECOMMENDED WAY FOR CONNECTING PHONES WITH BOX

For best results always connect your phone by this way. If you connect your phones by this why you will avoid lot of problem

Don’t Connect your JIG & Cable like this

Always connect like this!

HOW TO CONNECT MTK PHONES

Connect Jig to cable correct way as I show you above. Connect Power from main cable to Phone. Select MTK tab from Volcano box software. Click on Read Flash/Write Flash/Format etc. Press and hold Power Button from Phone keyboard. Click on Run. It will done

IF YOU GOT ANY ERROR OR PROBLEMPLEASE CHECK OUR SUPPORT AREA

HOW TO CONNECT SPD PHONES

Connect Jig to cable correct way as I show you above. Connect Power from main cable to Phone. Select SPD tab from software. Click on read flash/ Write flash/Format etc. Select Proper Boot ac-cording to you phone cpu. Don’t press and hold power button (Keep in mind SPD phones don’t need to press and hold power buttons) click on run

There is Few type of SPD phones which you must need to select proper boot for example SPD6600L. SPD6610/20. SPD6800H etc. so how to know which SPD phone have SPD6600L CPU or 6610/201st of all, Connect mobile with digital power supply and do not press power button If you see your supply taking .05 this mean your phone is 6600LX (6600L7/6600L3 etc) series If you see your supply taking .03 this mean your phone is 661X (6610/6620 etc) series

SPD 6610

How to connect Mstar Phones

If your phone show 0.05 then you phone should be 6600L or 6800h etc. and if your phone show 0.03 then your phone should be SPD6610/20 so please check boots. If you got any other problem just check our support area.When you connect any SPD phone 1st time then it will ask for drivers. Please Install Lat-est SPD drivers from (for 32bit system) C:\Program Files\Volcano Team\VolcanoBox\Drivers\Phone Drivers\SPD New Drivers 1.5.6.1\x86\driver (for 64bit system) C:\Program Files\Volcano Team\VolcanoBox\Drivers\Phone Drivers\SPD New Drivers 1.5.6.1\x64\driver

Connect Jig to cable correct way as I show you above. Connect Power from main cable to Phone. Select Mstar tab from Volcano box software. Click on Read Flash/Write Flash/Format etc. Press and hold Power Button from Phone keyboard. Click on Run. It will done.

When you connect Mstar phone 1st time it will install Drivers. If still failed to install drivers then give path from C:\Program Files\Volcano Team\VolcanoBox\Drivers\Phone Drivers\Mstar 2

SPD 6610

This is Basic Guide for all Volcano Box users…. We Will Create more Advance Tutorial Shortly…