VIKING UNIVERSAL XPD 676 PUMPS - Section 633 FULL ...vp.salesmrc.com/pdfs/Sec_633.pdf · VIKING UNIVERSAL XPD 676 PUMPS - ... American Petroleum Institute’s design standard for

VIKING PUMP • A Unit of IDEX Corporation • Cedar Falls, IA ©2015

Section 633Page 633.1Issue B

VIKING UNIVERSAL XPD 676 PUMPS - FULL COMPLIANCE with API 676 STANDARDS

SERIES 4223AX & 4323AX

Heavy-Duty, Foot-Mounted Internal Gear Pumps Offering Full Compliance with API 676 Design Standards for rotary positive displacement pumps in petroleum, chemical, and gas industry services.

HL4323AX

N4323AX

Pump SizeFlow Rates

GPM M3/hrHL 30 6.8KK 100 23LS 200 45Q 300 68

QS 500 114N 600 136R 1100 250

Nominal Flow Rates:

Steel Externals Series 4223AX & 4323AXNominal Flow

(GPM) 15 - 1100

(M3/hr.) 3.4 - 250

Pressure Range

(PSI) To 200 PSI

(Bar) To 14 Bar

Temp. Range

( oF ) −20°F to +400°F

( oC ) −29°C to +205°C

Viscosity Range

(SSU) 28 SSU to 35,000 SSU

(cSt) 0.1 cSt to 7,700 cSt

Operating Range:

Note: Lower temperatures available with special materials. Higher pressures available with factory approval.

Series DescriptionThe Universal XPD 676 Series Internal Gear pumps are designed and manufactured to comply fully with the current version of American Petroleum Institute’s design standard for positive displacement pumps, API 676. Applications include oil and gas and petrochemical industries where exceptional reliability is required.





Features Required by API 676 that are standard in XPD 676 seriesA few of the key features that are required for full compliance include:

● API 682 Seal. Viking’s seal chamber will accept almost any customer-specified brands and types of API 682-compliant Category 1, 2 or 3 cartridge mechanical seals, and can provide API seal plans to meet application requirements. Standard seal is a category 2 single mechanical seal. Carbon vs. silicon carbide with API Plan 13.

● 3mm corrosion allowance above Maximum Allowable Working Pressure (MAWP). The XPD 676 has an additional 3mm corrosion allowance built into all pressure containing components over and above our standard steel Universal Seal series pumps.

● 25,000 hour L-10 life on tapered roller bearings. Standard on all sizes at maximum speed and pressure.

● Steel castings to be normalized and tempered. Standard. ● High Strength Bolting. XPD 676 features high strength

fasteners stamped with manufacturer’s symbol and material codes, studs on some sizes. Threaded holes are drilled and tapped to minimum 1.5X stud diameter with minimum metal around the bottom of threaded holes at least 0.5X stud diameter plus 3mm corrosion allowance, per the specification.

● Casing drain and seal chamber vent. XPD 676 has cast-in casing drain with ANSI Class 300 RF flange and seal chamber vent to completely drain the casing before maintenance.

● Mounting surfaces flat and parallel. The mounting feet of XPD 676 pumps are machined to 6.3µm Ra, with flatness tolerance of 25µm. The upper surface is machined parallel to the foot, and where the pump has both bracket and casing feet (N & R sizes), the feet are machined flat and parallel, in the same plane within 150 µm/m (0.002 in./ft) of distance between the mounting surfaces after the pump is assembled.

● Rectangular keyways. Viking cuts rectangular keyways with required fillets and includes the key with each pump. Tapered shaft extension on shafts larger than 2.5”. Viking tapers the shaft extension on the “R” size for easy removal of the coupling half.

● Non-Destructive Evaluation of castings and post-weld evaluation of any necessary weld repairs using mag particle (MT) testing

● Certified hydrostatic testing to 1.5X MACP ● Certified performance testing in accordance with Section

3.6 of the Hydraulic Institute pump standards, at the specified viscosity (from 28 to 25,000 SSU), with data including speed, discharge pressure, suction pressure, power, and capacity.

● Packaging for long term storage, including corrosion inhibitor applied to exposed metal parts and metal port covers to protect internals from corrosion and contaminants

Viking XPD 676 pumps carry a five year limited warranty.

Additional Features & BenefitsBesides the features required by the API 676 standard, Viking offers many additional features and benefits that our customers commonly request, including:

● Jacketing to melt ambient-temperature solids like bitumen before startup. The XPD 676 features jacketed bracket and casing as standard, with option for jacketed head.

● Opposite ports with reversible direction of flow are standard, for easy in-line piping and the ability to transfer product in either direction or strip a line of product.

● O-Ring seals on head and casing joints instead of gaskets for maximum sealing effectiveness.

● Optional labyrinth seals on bearing housing for longest bearing life by minimizing contamination (lip seals standard).

● Grease lubrication standard, enabling re-greasing of pump during operation, without the need for shutdown.

● End clearance is easily adjusted to compensate for wear over time or for higher temperatures or viscosities, by simply rotating the threaded bearing housing.

55

● Documentation to include, at a minimum:

● There are many more requirements of the API 676 specification, and Viking has designed this pump to comply with all of them, as standard.

● Certified dimensional outline drawing

● Allowable flange loadings

● Cross-sectional drawing and bill of material

● Mechanical seal drawing and bill of material

● Performance curve

● Certified hydrostatic test data

● Material certifications (traceability)

● Weld procedure specification (WPS)

● Weld maps

● Non-destructive testing procedures

● Performance test procedures

● Performance test data

● Data sheets applicable to proposals, purchase and as-built

● Installation manual

● Operation and Maintenance manual

● Spare parts recommendations and price list

● List of drawings and submittals

● Shipping list





5. One-piece cast bracket provides rigid foundation to maximize seal and bearing life.

8. High strength fasteners have material grade and manufacturer’s identification symbols applied.

9. Mounting surfaces flat and parallel for superior alignment.

10. Casing drain cast-in with ANSI Class 300 Raised Face Flange to completely drain casing before maintenance.

3. Tapered roller thrust bearings provide minimum 25,000 hour L-10 life at maximum flow, pressure and viscosity.

Pump Construction and Features

6. Non-jacketed head standard. Optional Head Jacket available.

7. Seal chamber venting port for start-up and draining pump prior to maintenance.

1. Large diameter threaded bearing housing allows easy removal of cartridge seals.

2. Seal chamber accepts most brands of cartridge seals conforming to API 682. API Seal Plan 13 provided as standard. Other plans available.

4. Class 300 Raised Face flanges standard.

1.2.

3.

4.

5.

7.

10.8.

6.

9.





REVISIONSREV. DESCRIPTION ECN DATE

D

C

B

A

A

B

C

D

1

2

3

4

5

6

7

8

8

7

6

5

4

3

2

1

E

F

E

F

REV

EX-E

123-

37D

SHEET 1 OF 1

LS4223AX 3" OPPOSITE PORTED ANSI CLASS 300 RAISED FACE FLANGE PORTS AND 1/2" ANSI CLASS 300 RAISED FACE FLANGE DRAIN

1/20/2015--

cmihm

SCALE: 3:8

REVDWG. NO.

D

VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA 50613 U.S.A.

CHECKED

DRAWN

A.0

A.0

SIZE

THIS DRAWING IS THE PROPERTY OF VIKING PUMP, INC. AND IS PROPRIETARY IN GENERAL AND DETAIL. IT SHALL NOT BE COPIED OR ITS CONTENTS REVEALED TO OUTSIDE PARTIES WITHOUT THE WRITTEN CONSENT OF VIKING PUMP, INC.

EX-E123-37

PROJECT

3D WEIGHT

CASTING NUMBER

------ UNLESS OTHERWISE SPECIFIED ------DIMENSIONS ARE IN INCHES.INTERPRET DIM AND TOLERANCES PER VIKING PUMP ES-47BREAK EDGES .005-.015 RADIUS OR CHAMFER.XX .02 .XXX .005 ANGLES 1ALL FINISHED SURFACES

250 (AA .030

CUTOFF)ACCEPTABILITY OF SCREW THREADS SHALL BEDETERMINED BASED ON SYSTEM 21 ASME B1.3THIRD ANGLE PROJECTION

STATE

USE AND RELATED INFORMATION

WAS: EX-E123-37 403.32 lbs

E123

Work 01/20/2015

MATERIAL: SEE PARTS FOR MATERIAL SPEC

Model Number Key

L S 4 2 2 3 A X

Jacketing:2 = Jacketed Bracket & Casing3 = Foot Mount Casing

with Jacketed Bracket & Casing

Shaft Seal:4 = Mechanical Seal

Material of Construction:3 = Steel Externals

Size:HLKKLSQ

Series designed to comply with API 676

Basic Series Configuration

Field 1 Field 2 Field 3 Field 4 Field 5 Field 6 Field 7 Field 8

Materials of Construction

QSNR

Component Series: 4223AX and 4323AX

Casing Steel | ASTM A216, Grade WCC, normalized and tempered

Head Steel | ASTM A216, Grade WCC, normalized and tempered

Optional plate for head jacket Steel | ASTM A216, Grade WCC, normalized and tempered

Bracket Steel | ASTM A216, Grade WCC, normalized and tempered

Idler ②③ Cast Iron | ASTM A48 Class 35B

RotorStandard ① Cast Iron | ASTM A48, Class 35B

Steel Fitted ④ Steel | ASTM A148, Grade 80-40

Rotor Shaft ⑥ Steel | ASTM A108, Grade 1045

Idler Pin ⑤ Hardened Steel | ASTM A108, Grade 1045

Idler Bushing ⑥ Carbon Graphite

Bracket Bushing ⑥ Carbon Graphite

① KK, LS, QS and N sizes have ductile iron rotor, ASTM A536 Grade 60-40-18.

② Steel fitted Q and QS sizes have steel idler.

③ HL size has powdered metal idler, MPIF Std 35 FC-0208-50.

④ Material specifiction for HL steel rotor is AISI 8620, LS steel rotor is ASTM A148 80-50.

⑤ N & R size have hardened steel/ ASTM A322, Grade 8620⑥ Numerous material options, coatings and treatments available to satisfy specific application needs.

Bearing Housing

BracketAPI 682 Seal

Bracket Bushing

Rotor Shaft

Casing Rotor IdlerIdler

BushingIdler Pin

Head





U.S. Units:

Specifications – Jacketed Pumps

Model NumberStandard Port

Size

Nominal Pump Rating

(100 SSU)

Max. Hydrostatic Pressure

① Max. Discharge Pressure for 100

SSU Liquid at rated speed

② Max. Recommended Temp. for Standard Pump

Steel Fitted Recommended

Above

Approximate Shipping Weight

Inches GPM RPM PSIG PSIG (oF) SSU PoundsHL4223AX ③ 1 ½ 30 1750 400 200 350 7,500 170KK4223AX ③ 2 100 780 400 200 350 25,000 215LS4223AX ③ 3 200 640 400 200 350 75,000 360Q4223AX ③ 4 300 520 400 200 350 7,500 640QS4223AX ③ 6 500 520 400 200 350 75,000 700N4323AX ③ 6 600 350 400 200 225 75,000 1015R4323AX ③ 8 1100 280 400 200 225 25,000 2050

① For maximum recommended discharge pressures at different viscosities, see performance curves, which can be electronically generated with the Viking Pump Selector Program, located on www.vikingpump.com. If suction pressure exceeds 50 PSIG, consult factory. Higher pressures possible with factory approval based on application details.

② Higher temperatures can be handled with special construction and/or extra clearances, consult factory. Temperature based on Viton seal as standard. Lower temperature limits may be required when using other seal elastomers.

NOTE: H-N size pumps are standard with a jacketed bracket, jacketed casing and non jacketed head. R size pump is standard with a jacketed bracket, jacketed casing and jacketed head.

NOTE: H-N size pumps are standard with a jacketed bracket, jacketed casing and non jacketed head. R size pump is standard with a jacketed bracket, jacketed casing and jacketed head.

③ Ports are suitable for Class 300 ANSI steel or stainless steel companion flanges or flanged fittings.

Metric Units:

Model Number

④ Standard Port

SizeNominal Pump Rating

(22 cSt)Max.

Hydrostatic Pressure

① Max Discharge

Pressure for 22 cSt Liquid at rated speed

② Max Recommended Temp. for Standard Pump

Steel Fitted Recommended

Above

Approximate Shipping Weight

Inches M3/hr RPM BAR BAR (oC) cSt KG

HL4223AX ③ 1 ½ 6.8 1450 28 14 180 1,650 77KK4223AX ③ 2 23 780 28 14 180 5,500 98LS4223AX ③ 3 45 640 28 14 180 16,500 163Q4223AX ③ 4 68 520 28 14 180 1,650 290QS4223AX ③ 6 113 520 28 14 180 16,500 318N4323AX ③ 6 136 350 28 14 107 16,500 460R4323AX ③ 8 248 280 28 14 107 5,500 930

① For maximum recommended discharge pressures at different viscosities, see performance curves, which can be electronically generated with the Viking Pump Selector Program, located on www.vikingpump.com. If suction pressure exceeds 50 PSIG, consult factory. Higher pressures possible with factory approval based on application details.

② Higher temperatures can be handled with special construction and/or extra clearances. Consult factory. Temperature based on Viton seal as standard. Lower temperature limits may be required when using other seal elastomers.

③ Ports are suitable for Class 300 ANSI steel or stainless steel companion flanges or flanged fittings.

④ Port sizes are inch standard, not metric design or size.





Dimensions - HL4223AX

Note: All dimensional drawings shown with optional jacketed head.

Dimensions - KK4223AX

.62

1.19 1.45

18.10

3.83 8.63

6.00

1.32

.79

1.56 15.35

A A

PORTS: 2X 1-1/2" RAISED FACE FLANGES WITH STUDS AND NUTS (NOT SHOWN) SUITABLE FOR USE WITH CLASS 300 ANSI FLANGES

.99

.7500.7495

5.95

2.38

2.38

3.63

3.75

3.75 .19 X .12 RECTANGULAR KEYWAY

4X 3/4" NPTJACKET CONNECTIONSBRACKET

5.00 5.00

11.00 2X .75

.94

.94

2X 1/2" NPTJACKET CONNECTIONSHEAD

3.62

8.38

5.95

3.88

3.90

9.73

5.00

4.25

4.25

4X .69

.32

3.25

3.25

1.61

VIEW A-A

DRAIN: 1/2" RAISED FACE FLANGE WITH STUDS AND NUTS (NOT SHOWN) SUITABLE FOR USE WITH CLASS 300 ANSI FLANGES

3X 1" NPTJACKET CONNECTIONSCASING

STANDARD MODELS: HL4223AXNOTES:1. ALL DIMENSIONS ARE FOR REFERENCE ONLY.DWG. NO. REV.

DRAWN

CHECKED

SHEET 1 OF 1 A.0

01/15/20153D

THIS DRAWING IS THE PROPERTY OF VIKING PUMP, INC. AND IS PROPRIETARY

IN GENERAL AND DETAIL. IT SHALL NOT BE COPIED OR ITS CONTENTS REVEALED TO OUTSIDE PARTIES WITHOUT THE WRITTEN

CONSENT OF VIKING PUMP, INC.


STATE

cmihm 1/7/2015

VCI 01/15/2015

DIMENSIONS ARE ININCHES

E123PROJECT:WAS: HV-3960

Released 01/15/2015

.59

1.75 1.94

2.25 16.33 20.33

4.25 2.00

7.74

6.50

4.38

1.68

1.20

A A

PORTS: 2X 2" RAISED FACE FLANGES WITH STUDS AND NUTS (NOT SHOWN) SUITABLE FOR USE WITH CLASS 300 ANSI FLANGES


11.00 2X .75

7.25 7.25

1.75

1.75

2X 1" NPTJACKET CONNECTIONSHEAD

1.12501.1245

1.42 3.62

6.02

2.41

2.41

3.63

3.63

4X 3/4" NPTJACKET CONNECTIONSBRACKET

1/4 X 3/16RECTANGULAR KEY

5.12

5.13

6.02

3.87

9.13 10.42

3.25

3.25

2.00 3.50

4.38

4.38

4X .75

5.63

VIEW A-A


STANDARD MODELS: KK4223AXNOTES:1. ALL DIMENSIONS ARE FOR REFERENCE ONLY.

DWG. NO. REV.DRAWN

CHECKED

SHEET 1 OF 1 A.0

01/15/20153D





STATE

cmihm 1/7/2015

VCI 01/15/2015


E123PROJECT:WAS: KV-2487

Released 01/15/2015





Dimensions - LS4223AX

2.55

3.50 20.65

2.44

26.59

2.25

4.75

4.55

8.39

7.00

2.06

1.52

A ADRAIN: 1/2" RAISED FACE FLANGE WITH STUDS AND NUTS (NOT SHOWN) SUITABLE FOR USE WITH CLASS 300 ANSI FLANGES


1.43751.4370

2.55 4.25

8.18

2.75

2.75 4.00

4.00

4X 1" NPTJACKET CONNECTIONSBRACKET

.38 X .25RECTANGULAR KEYWAY

12.50

8.00 8.00

2X .62

3.00

3.00


4.00

10.00

6.68

6.25

8.18

11.24

1.38 5.00

5.00

5.00

3.25

3.25

6.25

4X .75

VIEW A-A


STANDARD MODELS: LS4223AXNOTES:1. ALL DIMENSIONS ARE FOR REFERENCE ONLY.DWG. NO. REV.

DRAWN

CHECKED

SHEET 1 OF 1 A.0

01/15/20153D





STATE

cmihm 1/7/2015

VCI 01/15/2015


E123PROJECT:WAS: LV-4266

Released 01/15/2015Dimensions - Q4223AX

4.26 3.00

28.06

5.35 10.52

9.50 6.25

2.00

2.69

2.08

4.44 20.62

A ADRAIN: 3/4" RAISED FACE FLANGE WITH STUDS AND NUTS (NOT SHOWN) SUITABLE FOR USE WITH CLASS 300 ANSI FLANGES


13.25 8.25 2X .88

10.25 10.25

4.50

4.50


1.9371.936

3.58

3.63

3.63

5.00

5.00

8.63

5.13



8.00

8.50

8.63

5.75

13.25 14.87

3.00

3.00

2.03 6.25

4X .88

5.25

5.25

VIEW A-A

5X 1-1/2" NPTJACKET CONNECTIONSCASING

STANDARD MODELS: Q4223AXNOTES:1. ALL DIMENSIONS ARE FOR REFERENCE ONLY.

DWG. NO. REV.DRAWN

CHECKED

SHEET 1 OF 1 A.0

01/15/20153D





STATE

cmihm 1/7/2015

VCI 01/15/2015


E123PROJECT:WAS: QV-2059

Released 01/15/2015






Dimensions - N4323AX

7.00

3.00

11.00

4.31

9.49

6.37

9.50

4.60 6.00

26.93 4.50 37.43

29.64

2.75

2.61

A A


3.62

2.43752.4365

6.00

11.50

3.75

3.75 7.00

7.00

.62 X .44RECTANGULAR KEY

4X 1" NPTJACKET CONNECTIONSBRACKET 5X 1-1/2" NPT

JACKET CONNECTIONSCASING

12.00 12.00

4X 1.00 8.75

8.75

5.75

5.75


5.75

13.25

11.50

6.88

6.62

15.44


1.43

6.25

10.25

10.25 5.50

5.50

3.00 1.66

17.26

4X .88

4X .88

14.00 23.61

VIEW A-A

STANDARD MODELS: N4323AXNOTES:1. ALL DIMENSIONS ARE FOR REFERENCE ONLY.DWG. NO. REV.

DRAWN

CHECKED

SHEET 1 OF 1 A.0

01/15/20153D





STATE

cmihm 1/7/2015

VCI 01/15/2015


E123PROJECT:WAS: NV-744

Released 01/15/2015

Dimensions - QS4223AX

9.50

4.26

4.00

29.56

3.00

6.25

10.52 5.85

2.69

2.08

4.44 21.12

A A



9.13

5.13

1.9371.936

3.58

3.63

3.63

5.00

5.00



13.25 8.50 2X .88

10.25 10.25

8.50 4.50

4.50


9.13

5.75

13.25 8.00

14.87

5.25

5.25

6.25

2.03

4X .88

3.00

3.00

VIEW A-A


STANDARD MODELS: QS4223AXNOTES:1. ALL DIMENSIONS ARE FOR REFERENCE ONLY.DWG. NO. REV.

DRAWN

CHECKED

SHEET 1 OF 1 A.0

01/15/20153D





STATE

cmihm 1/7/2015

VCI 01/15/2015


E123PROJECT:WAS: QV-2060

Released 01/15/2015






Dimensions - R4323AX

13.25

7.16 5.00 10.00

6.62

44.44 29.02

5.62

5.00

4.25

13.50

10.00

8.80

30.01

A A


3.43753.4355

7.00

12.38

5.00

5.00 9.00

9.00

4X 1-1/2" NPTJACKET CONNECTIONSBRACKET


TAPERED SHAFT,3/4" TAPER PER 1 FOOT

14.25 14.25

4X 1.00

7.00

4.00

5.50 5.50

10.44 10.44

3X 1-1/2" NPTJACKET CONNECTIONSHEAD

8.63

9.75

12.38

8.25

18.25 20.50

Y

DRAIN: 1" RAISED FACE FLANGE WITH STUDS AND NUTS (NOT SHOWN) SUITABLE FOR USE WITH CLASS 300 ANSI FLANGES

13.25

13.25

30.35 7.75

7.75 19.00

1.68

6.50

1.90 3.25

4X 1.00

4X 1.00 VIEW A-A

6.00 .12

3.50

1.15

DETAIL YSCALE 1 : 8

.88 X .62RECTANGULAR KEYPARALLEL TO TAPER






INLET CONDITIONS: The performance curves show “Based on 10 (or 15) In.-Hg.,” which is the standard test condition. This is not the maximum vacuum capability of the pump.

NPSH (Net Positive Suction Head): The NPSHR (Net Positive Suction Head Required by the pump) is given in the table below and applies for viscosities through 750 SSU. NPSHA (Net Positive Suction Head – Available in the system) must be greater than the NPSHR. For a complete explanation of NPSH, see Application Data Sheet AD-19.

FOR VISCOSITIES UP TO 750 SSU – See NPSHR table below.

FOR VISCOSITIES GREATER THAN 750 SSU (NPSHR data not available): The performance curves are based on 10 or 15 In.-Hg. While vacuums up to 20 In.-Hg. will not generally result in any loss of capacity, it is recommended that the suction line size and possibly the pump port size

be increased to hold the expected vacuum to 15 In-Hg. or less. Vacuum above 20 In.-Hg. should be avoided. Refer to General Catalog, Engineering Section 510 for information on determining line size.

THIN LIQUIDS: pump capacity when handling 28 SSU liquids (solvents, etc.) is shown on the 38 SSU performance curve as a broken line. Pressure shown on broken line is maximum recommended for 28 SSU liquid. Horsepower for 28 SSU is same as 38 SSU at any given pressure. Carbon graphite bushings must be used handling 28 SSU liquids.

MECHANICAL EFFICIENCY: The Mechanical Efficiency (expressed in percent) can be calculated using the following formula:

Mechanical Efficiency = (Differential Pressure, PSI) (Capacity, GPM) (100)

(Horsepower, BHP) (1715)

Performance Curve Notes

Printed performance curves are not available.

Performance curves can be electronically generated with the Viking Pump Selector Program. This program can be located on www.vikingpump.com for the general public.

For authorized distributors, this program can be found listed under the “Products” tab at www.idexconnect.com. Security passwords are required to access IDEXconnect.

NPSHR – FEET OF LIQUID (Specific Gravity 1.0), Viscosities up to 750 SSUSteel Externals Series 4223AX and 4323AX

PUMP SIZE

PUMPS SPEED, RPM100 125 155 190 230 280 350 420 520 640 780 950 1150 1450 1750

HL - - - 1.7 1.8 1.9 2.1 2.4 2.8 3.4 4.5 6.2 9.5 13.5

KK - 1.7 1.8 1.9 2.1 2.3 2.8 3.3 4.4 6.3 9.1 - - - -

LS 1.6 1.8 2.0 2.2 2.5 3.0 3.8 5.0 7.3 10.8 - - - - -

Q, QS 1.9 2.1 2.3 2.7 3.3 4.2 6.1 8.4 12.7 - - - - - -

N 2.1 2.3 3.5 4.5 6.3 9.5 15.0 - - - - - - - -

R 2.7 3.2 4.2 5.8 8.2 11.9 - - - - - - - - -

METRIC CONVERSION: The following table has been compiled for conversion to metric values.

VACUUM PRESSURE CAPACITYIn.-Hg (inches of mercury)

KPa* (Kilopascals) PSI (lb./in2) kPa*

(Kilopascals) BAR GPM (US gal/minute)

LPM (Liter/Minute) M3/hr

1 3.4 1 6.9 0.07 1 3.8 0.235 17 25 172 1.7 0.26 1 0.0610 34 50 345 3.4 4.4 16.7 115 51 100 690 6.920 68 150 1034 10.325 85 200 1379 13.8

250 1724 17.2

* 100 kPa = 1 bar

Documents

VIKING UNIVERSAL XPD 676 PUMPS - Section 633 FULL ...vp.salesmrc.com/pdfs/Sec_633.pdf · VIKING UNIVERSAL XPD 676 PUMPS - ... American Petroleum Institute’s design standard for