Embed Size (px)
Citation preview
1 2
Reset
Wearing
Eng
lish
Eng
lish
Eng
lish
Eng
lish
Control
4
Power on
Power O�
Play/PauseVolume-Volume+Play PreviousPlay NextAnswer/Hang up phone callReject phone callSwitch between two callsManually enter into pairing modeActivate voice assistant
Automatic: Open the charging case, take out the earbuds, the earbuds will automatically power on Manual: Long press the MFB for 1.5 seconds in shutdown statusAutomatic: Place the earbuds back into the charging case.Manual: Long press the MFB for 10 seconds in working status.Double tap MFBTap MFB(L) onceTap MFB(R) oncePress the MFB(L) for 1.5 secondsPress the MFB(R) for 1.5 secondsDouble tap MFB(L/R)
Press the MFB(L/R for 1.5 secondsLong press the MFB(L/R )for 2 secondsLong press the MFB(L/R )for 6 seconds
Triple tap MFB(L/R )
3
Product Diagram
Eng
lish
1. Connect to a Type-C charging adapter charge it.(Charging current does not exceed 1A).
2. When not using for a long time, please charge it once every three months at least.
Q3: How to charge the charging case?First use
Please open the lid of the charging case, take out the two earbuds, and tear o� the insulating �lm on the earphone charging contacts, then put the earbuds back into the charging case.1.Open the charging case, take out the two earbuds, the earbuds will
automatically power on and start to paring with each other. One earbud’s white LED is on, another one is blinking with white and red light, which indicates that the earbuds has entered pairing mode.
2. Turn on the bluetooth of your device, and please choose“SOUNDPEATS S5”in the list to pair, then the earbuds will connect with your device.
SOUNDPEATS S5 Connected
S5S5
User Guide | Gebrauchsanweisung | Manual de instrucciones |
Mode d'emploi | Istruzioni per l'uso | 说明使用指南
1. Clear the pairing data from your device. 2. Put both earbuds into the charging case. Make
sure they are in charging status.3. Then long press the MFB of both earbuds for 10
seconds at the same time until the LED indicator in both earbuds �ash white and red twice. The reset �nish.
1. Identify the le� and right earphones. Adjust the earphones to �t your ears.2. Right and wrong way of wearing.
6
1. The charging case has no power. The earphone will not power o� in charging case when charging case has no power.
2. Make sure the earphone is properly placed in the charging case. Please try to clean the contact area between the charging box and the earphones with a so� cloth, keep the charging metal piece and pin clean.
Q4: Why does the earphone still connect to the mobile phone after putting it back into the charging case ?
A single charge not allow the earbuds to last 20 hours. 5 hours playtime per charge and another 3 recharges by charging case.
Q5: Why is the playtime not as described?
Eng
lish
7
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o� and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit di�erent from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference.(2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifcations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Statement
FCC ID: 2AFTU-DD023 Made in China
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
www.soundpeatsaudio.com
MANUFACTURERShenzhen SoundSOUL Information Technology Company Limited.
Company：Qing UG(haftungsbeschränkt)Address：Undinestr. 7, 12203 Berlin Germany
EC REP
5
Q&A
Eng
lishQ1: What does the LED indicator mean when
the earphone is charging?
During the charging, the LED show red light, it will turn o� when full charged.
Q2: What does the LED indicator on the charging case mean?
During the charging, the indicator light �ashes to show the remaining power of the charging case.The �rst white LED light �ashes to show 0-24% remaining power of the charging case.The �rst white LED light is on and the second LED �ashes to show 25%-49% remaining power.Two white LED lights are on and the third LED �ashes to show 50%-74% remaining power of the charging case.Three white LED lights are on and the fourth LED light �ashes to show 75%-99% remaining power of the charging case.4 lights are all on when full charged.
25% - 49%
0% - 24%
50% - 74%
75% - 100%
100%
1.5s 3x 2x 1x 1.5s 2s2s 3x2x1x
