Section 1 - Installing the Smart Control Receiver

2. Measure distance (2) from the screw hole of mounting bracket to the button of the wall console of approximately 30 - 40 mm.

1. Slightly insert (1) the mounting bracket (C) behind the wall console.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

1. Open the clip cover (1) of the Smart Control Receiver (A) with a screwdriver and insert two AA batteries (2).

2. Position the actuator (3) on the Smart Control Receiver (A) to ensure it touches the Wall Console button.

3.

4.

Congratulations on your purchase of the Skylink Universal Garage Door RemoteControl model MF-1. The Receiver and Remote Control is designed to work

with any garage door opener brands to give you the convenient, secure accessto your garage and home.

INSTALLATION INSTRUCTIONS

Universal Garage Door Remote Control

Model: MF-1

Safety Information Package Contents

WARNING: This Garage Door Remote Control kit should only be installed to a garage door

NOTE: Remove the mounting bracket from the back of the Smart Control Receiver.

Section 2 - Powering the Smart Control Receiver

WARNING: Do not let children use the garage door remote without adult supervision.

opener equipped with safety infrared sensor.

WARNING: Changes or modi�cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the product. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:

Re-orient or re-locate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced technician for help.

NOTE: equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

Parts Description Quantity

A Smart Control Receiver 1

B 3-Button Keychain Remote 1

C Mounting Bracket 1

D Screws & Anchors 3

NOTE: A 6V DC, 300mA adapter (sold separately) may be required if to operate the Smart Control Receiver continuously.

Insert the Touch Plate (4) on the clip cover (1) of the Smart Control Receiver (A).

Close the clip cover (1) of the Smart Control Receiver (A).

A

C

E

B

C

(1)

30 -

40 m

m

(2)

(2)

(4)

(1)

3

A

NOTE: Use provided screws (D) and plastic anchors (D) for the brick wall.

NOTE: Use Spring Toggles for drywall or hollow wall with a thickness less than 1 inch.

3. Mark 2 holes on the drywall with a pencil.

4.

5.

Drill a 1/4” (6mm) hole in the drywall for the anchor and screw (D).

Drill a 3/8” (10mm) hole in the drywall for the Spring Toggles (E).

Section 1 - Installing the Smart Control Receiver (Continued)

1/4” (6mm)

1/8” (10mm)

Screw-in the screw to the Spring Toggles (E) with the Mounting Bracket (C).6.

Fold the Spring Toggles (E) completely and slip it into the hole. Push ituntil the wings opens.

7.

Tighten the screw (E) and ensure the mounting bracket (C) is securely installed to the wall.8.

Screw-in the other screw (D) to secure the mounting bracket (C).9.

Clip in the Smart Receiver (A) on the mounting bracket (C) and push it up to lock it.10.

AC

C

C

C

E

C

E E

E

D

E Spring Toggle 1

D

Section 7 - Remote Control Password FeatureSection 6 - Erasing the Remote from Smart Control ReceiverPACKAGE CONTENTSSection 5 - Programming the Remote Control

NOTE: You must program your keychain remote control (B) to the Smart Control receiver (A) in order for the two to communicate.

NOTE: To erase the unwanted remotes from the Smart Control Receiver, �rst erase all the programmed remotes, then learn the ones you would like to keep.

1. Press and hold the “PROG”(1) button on the Smart Control Receiver (A) for 2 seconds. The red LED (2) will start �ashing continuously for 10 seconds.

1. Press and hold the “PROG” button (1) on the Smart Control Receiver (A) for approximately 10 seconds.

2. The LED (2) will �ash rapidly after 10 seconds indicating that all the programmed remotes have been erased. You may release the “PROG” button (1).

Section 4 - Operating

1. Press the programmed button (1) on the keychain remote (B) or press the touchplate (2) on the Smart Control Receiver (A) to push the wall button which will open/close the garage door.

NOTE: The keychain remote comes with lithium battery installed. Remove the battery isolator

tag from the keychain remote control before using.

NOTE: There are three buttons on your remote control (B). Each button can be used to controlone smart control receiver (A). Additional Smart Control receiver is sold separately.

2 Press the button (3) on the remote (B) you plan to use.

3. Once the remote (B) is programmed, the red LED on the Smart Control Receiver (A)will �ash slowly.

When the operating range is reduced, or when the LED does not �ash during operation, it is time to replace the battery.

1. Undo the two screws (1) on the back of the remote. The bottom case (2) will then come off.

2. Take out the old battery (3).

3. Place the new battery (3) in position - positive side up.

4. Close the cover (2) and re-insert the two screws (1).

TroubleshootingSection 10 - Replacing the Battery

NOTE: Dispose of old battery promptly and properly.

Problem Solution

The LED on the remote does not turn on when the button is pressed.

Check if the battery isolator is removed and if the battery is properly installed.

The LED on the remote �ashes but does not operate the garage door.

- Check if the correct button is pressed.- Ensure that the remote has been programmed to the Smart Control Receiver.- Check if the password function is enabled.- Reset the remote, disable the password function and refer to the programming section to program the remote to the Smart Control Receiver.

The LED on the Smart ControlReceiver does not turn on.

- Check if the batteries are properly installed.- Add a 6VDC, 300mA adapter (sold separately) to operate the Smart Control Receiver continuously.

The remote is powered by a Lithium battery CR2032 (included). Follow the instructionsbelow to replace the battery of the remote.

(3)

(2)(1)

1. To reset the password, press buttons 1 and 2 simultaneously and hold for more than 15 seconds until the LED (4) �ashes.

2. After you release buttons 1 and 2, the LED (4) will be turned off and the remote will be reset back to factory default password.

Section 9 - Resetting the Remote Control Password

NOTE: After resetting the Remote, the password feature will be disabled and the password

NOTE: The password can be 2-8 digits long and can be a combination of buttons 1,2, and 3.

NOTE: This function allows you to enter a password before pressing the garage door button you assigned, for additional security.

NOTE: Leave a 1 second pause period between entering the password and operating the garage door. The factory default password is 2,2,2. The password setting on the remote control (B) comes disabled as per factory default.

1. To enable or disable the password, press buttons 1 and 3 simultaneously and hold for at least 5 seconds until the LED �ashes quickly, but not until the LED �ashes slowly.

2. Input the password (factory default 2,2,2).

3. Press button 1 and 3 once simultanesously to con�rm. If the password is correct, the password protection will be enabled/disabled.

4. To control your garage door, press the password 2,2,2 and 1 (the assigned button for your garage door.

NOTE: If you enable the password protection, you can only operate the remote control (B), after you input the correct password.

1. To change the password, press buttons 1 and 3 simultaneously and hold for at least 10 seconds. The LED (4) will change from �ashing quickly to �ashing slowly.

2. Input the old password (factory default 2,2,2).

3. Press buttons 1 and 3 simultaneously to con�rm. If the password is wrong, the LED (4) will �ash three times, and you have to restart.

4. Input the new password.

5. Press buttons 1 and 3 simultaneously to con�rm.

6. The password has now been changed, and the password protection is now enabled.

Section 8 - Changing the Remote Control Password

will change back to the factory default 2,2,2. You need to re-program the remoteto the Smart Control Receiver again.

4

1

2

3

B 4

3

2

1

B

B

1

A

2

1

A

2

B

3

A

B

2

1

Warranty

ONE YEAR WARRANTY

This product is guaranteed to be free of defects in materials and workmanship for 1 year from the date of purchase. If this product is defective, call 1-800-304-1187 for repair or replacement parts. Guarantee does not include normal wear and tear or batteries.

If you have any questions, problems or missing parts, please call Skylink Customer Support:9:00am - 5:00pm EST, Monday-Friday.

Or e-mail us at support@skylinkhome.com

P/N : 101Y169 Rev:1©2014 SKYLINK GROUP.

CUSTOMER SERVICE17 Sheard Avenue,Brampton, Ontario,Canada L6Y1J3

1-800-304-1187

www.skylinkhome.com

Section 3 - Resetting the Smart Control Receiver

1. Press and hold the “PROG” button (1) on the Smart Control Receiver (A) for 5 seconds until the LED stays Solid.

2. The actuator (2) will reset to the highest position.

NOTE: The actuator can be detachable to provide different actuating range to match the wall button or wall console. Pull out the actuator from its position, reverse and re-install to the unit.

Extend or retract the actuator from its position to ensure the actuator can make contact with the wall button to activate the garage door.

A A

1 NOTE:

To extend the actuator, take it out and place it reversed.To make it shorter, remove the actuator.

NOTE:

2