UA5000 Operation Manual-PVM Volume.pdf

Manual Guide i..................................................................................Overview i......................................................................................................Control Boards and Related Operation Manuals i..........................................Service Configuration ii...................................................................................

Part I Basic ConfigurationChapter 1 Connecting to the System 1-1...........................................................

1.1 Connecting to the System Through Local Serial Port 1-1.......................1.1.1 Connecting Serial Port Cable 1-1...................................................1.1.2 Running the HyperTerminal 1-1......................................................1.1.3 Setting up Terminal Communication Parameters 1-2.....................1.1.4 Setting up Terminal Type 1-3.........................................................1.1.5 Setting up Line Delay and Character Delay 1-4.............................1.1.6 Log in to the System 1-5.................................................................

1.2 Connecting to the System Through Remote Serial Port 1-5...................1.2.1 Setting up the Called Modem 1-6...................................................1.2.2 Setting up the Calling Modem 1-7..................................................1.2.3 Setting up Configuration Environment 1-8......................................1.2.4 Running the HyperTerminal 1-8......................................................1.2.5 Logging in to the System 1-9..........................................................

1.3 Connecting to the System Through Telnet Terminal 1-9........................1.3.1 Setting up Configuration Environment 1-10......................................1.3.2 Run Telnet Application 1-10.............................................................1.3.3 Logging in to the System 1-11..........................................................

Chapter 2 Getting Started with CLI 2-1..............................................................2.1 Command Line Operation Characteristics 2-1........................................

2.1.1 Intelligent Matching 2-1...................................................................2.1.2 Editing Characteristics 2-1..............................................................2.1.3 Character Meaning 2-2...................................................................2.1.4 Command Mode 2-3.......................................................................

2.2 Basic Operations of the CLI 2-5..............................................................2.2.1 Setting Online Help Mode 2-5.........................................................2.2.2 Setting Interactive Input Mode 2-7..................................................2.2.3 Setting Screen Scrolling Mode 2-7.................................................2.2.4 Changing Display Language 2-8....................................................2.2.5 Setting Command Echo Display 2-8...............................................2.2.6 Clearing Terminal Screen 2-9.........................................................2.2.7 Setting Terminal Type 2-9..............................................................2.2.8 Setting Terminal Timeout Exit 2-9..................................................2.2.9 Holding Terminal 2-10......................................................................

2.2.10 Querying History Commands 2-11.................................................2.2.11 Configuring Host Name 2-11..........................................................2.2.12 Setting System Time 2-11..............................................................2.2.13 Connectivity Test Commands 2-11.................................................

Chapter 3 Managing a User 3-1.........................................................................3.1 Overview 3-1...........................................................................................3.2 User Management 3-2............................................................................

3.2.1 Adding a User 3-2...........................................................................3.2.2 Deleting a User 3-3.........................................................................

3.3 User Attributes Modification 3-3..............................................................3.3.1 Modifying User Authority 3-3..........................................................3.3.2 Modifying User Password 3-4.........................................................3.3.3 Modifying User Reenter Number 3-4..............................................3.3.4 Modifying User Attached Information 3-4.......................................3.3.5 Querying a User 3-4.......................................................................3.3.6 Disconnecting a Login User 3-5......................................................

Chapter 4 Managing System Output Information 4-1.........................................4.1 Overview 4-1...........................................................................................4.2 Controlling the Output to CLI terminal 4-1...............................................

4.2.1 Querying the Command Line Client Information 4-2......................4.2.2 Set the infoswitch of a CLI Terminal 4-2.........................................4.2.3 Querying the infoswitch of a CLI Terminal 4-2................................4.2.4 Setting the infolevel of a CLI Terminal 4-2......................................4.2.5 Querying the Control Level for Information Output to CLITerminal 4-3.............................................................................................

4.3 Controlling the Output to NMS Terminal 4-3...........................................4.3.1 Setting the infoswitch of an NMS Terminal 4-3...............................4.3.2 Querying the infoswitch of an NMS Terminal 4-3...........................4.3.3 Setting the infolevel of an NMS Terminal 4-3.................................4.3.4 Querying the infolevel of an NMS Terminal 4-4..............................

4.4 Controlling the Output to Log Host Terminal 4-4.....................................4.4.1 Setting the infoswitch of a Log Host Terminal 4-4..........................4.4.2 Querying the infoswitch of a Log Host Terminal 4-4.......................4.4.3 Setting the infolevel of a Log Host Terminal 4-4.............................4.4.4 Querying the infolevel of a Log Host Terminal 4-5.........................

Chapter 5 NMS Configuration 5-1......................................................................5.1 Configuring PVM Network Interfaces 5-1................................................

5.1.1 Configuring the Network Interface Address 5-1..............................5.1.2 Configuring the Route 5-1...............................................................

5.2 Configuring an NMS Workstation 5-1......................................................5.2.1 Adding an NMS Workstation 5-1....................................................

5.2.2 Activating an NMS Workstation 5-2................................................5.2.3 Querying NMS Workstation Parameters 5-2..................................5.2.4 Deactivating an NMS Workstation 5-3............................................5.2.5 Deleting an NMS Workstation 5-3..................................................5.2.6 Modifying an NMS workstation 5-3.................................................5.2.7 Managing NMS Terminal Output Control 5-4.................................

5.3 Configuration Examples 5-4....................................................................Chapter 6 Frame Configuration 6-1....................................................................

6.1 Configuring a Frame 6-1.........................................................................6.1.1 Adding a frame 6-1.........................................................................6.1.2 Deleting a frame 6-2.......................................................................

6.2 Configuring an Inter-frame Link 6-2........................................................6.2.1 Adding an Inter-frame Link 6-2.......................................................6.2.2 Querying an Inter-frame Link 6-3....................................................6.2.3 Delete an inter-frame link 6-4.........................................................

6.3 Configuring Frame Attributes 6-4............................................................6.3.1 Configuring Frame Attributes 6-5....................................................6.3.2 Configuring EMU of Frame 6-5.......................................................6.3.3 Querying Frame Attributes 6-5.......................................................

Chapter 7 Board Configuration 7-1.....................................................................7.1 Overview 7-1...........................................................................................7.2 Configuring a Board 7-1..........................................................................

7.2.1 Querying Board Information 7-1.....................................................7.2.2 Adding a Board 7-3.........................................................................7.2.3 Confirming a Board 7-3...................................................................7.2.4 Deleting a Board 7-4.......................................................................7.2.5 Prohibiting/Unprohibiting a Board 7-4.............................................

7.3 Querying Board Version 7-5....................................................................7.4 Querying Board CPU Usage 7-5.............................................................7.5 Resetting a Board 7-5.............................................................................

Part II Service ApplicationChapter 8 MG Interface Configuration 8-1.........................................................

8.1 Overview 8-1...........................................................................................8.2 MG Interface Configuration 8-1...............................................................

8.2.1 Adding an MG Interface 8-1............................................................8.2.2 Starting/Closing an MG Interface 8-1.............................................8.2.3 Deleting an MG Interface 8-2..........................................................8.2.4 Configuring MG Interface Protocol Parameter 8-2.........................8.2.5 Configuring Dual Homing 8-4.........................................................8.2.6 Configuring MGC Forced Switchover 8-4.......................................

8.2.7 Configuring Equipment Authentication 8-4.....................................8.2.8 Querying MG Interface Information 8-5..........................................8.2.9 Configuring MGCP Stack Parameter 8-6........................................8.2.10 Configuring H.248 Stack Parameter 8-8.......................................8.2.11 Configuring Ringing Mapping Entry 8-9........................................8.2.12 Configuring MG Interface Software Parameters 8-11.....................8.2.13 Configuring System Parameters 8-13.............................................8.2.14 Configuring A/u Law 8-15...............................................................8.2.15 Configuring SNTP Client 8-16........................................................8.2.16 Configuring DNS Client 8-16..........................................................

Chapter 9 Narrowband Subscriber Configuration 9-1........................................9.1 Adding a Narrowband Subscriber 9-1.....................................................

9.1.1 Adding a single MG subscriber 9-1.................................................9.1.2 Adding a batch of MG subscribers 9-1...........................................

9.2 Deleting a Narrowband Subscriber 9-2...................................................9.3 Modifying the Narrowband Subscriber Data 9-2.....................................9.4 Setting Port Gain, Pulse Dial and Polarity Reversal forNarrowband Subscriber 9-2..........................................................................9.5 Setting 16/12KC Attribute of Narrowband Subscriber Port 9-3...............9.6 Querying Narrowband Subscriber 9-4.....................................................9.7 Terminating/Restarting Narrowband Subscriber Port Service 9-5..........

Chapter 10 SPC Configuration 10-1.....................................................................10.1 Overview 10-1.........................................................................................10.2 Configuring an SPC 10-1........................................................................

10.2.1 Adding an SPC 10-1.......................................................................10.2.2 Deleting an SPC 10-3.....................................................................10.2.3 Querying an SPC 10-3....................................................................10.2.4 Releasing SPC 10-3.......................................................................10.2.5 Setting up SPC 10-4.......................................................................10.2.6 Modifying SPC Parameter 10-4......................................................

Chapter 11 Application of Voice Service 11-1......................................................11.1 Overview 11-1.........................................................................................11.2 Voice Service Configuration 11-1............................................................

11.2.1 Networking and Data Explanation 11-1..........................................11.2.2 Configuring Data 11-4.....................................................................

Part III Maintenance GuideChapter 12 System Maintenance 12-1.................................................................

12.1 Overview 12-1.........................................................................................12.1.1 System Management Files and Storage Media 12-1......................12.1.2 Upgrade Procedures for System with One Control Board 12-1......

12.1.3 Upgrade Procedures for System with Two Control Boards 12-2....12.2 Managing System Data 12-4...................................................................

12.2.1 Saving Data 12-4............................................................................12.2.2 Duplicating Data 12-5.....................................................................12.2.3 Backing up Data 12-5.....................................................................12.2.4 Erasing Data 12-6...........................................................................

12.3 System Switchover 12-7.........................................................................12.3.1 Setting Data Synchronization Switch 12-7......................................12.3.2 Querying Data Synchronization State 12-8....................................12.3.3 Manual Switchover 12-8.................................................................

12.4 Loading Software 12-9............................................................................12.4.1 Setting FTP User Name and Password 12-9..................................12.4.2 Power-on Loading 12-9..................................................................12.4.3 Loading BIOS File Online 12-14.......................................................12.4.4 Loading Host Program File Online 12-15.........................................12.4.5 Loading Host Database File Online 12-19........................................12.4.6 Loading Multi-Language Resource File Online 12-20......................12.4.7 Host Version Rollback 12-21............................................................

12.5 Managing Logs 12-21...............................................................................12.5.1 Setting Log Host 12-21.....................................................................12.5.2 Querying Log 12-22..........................................................................

12.6 Managing Patches 12-22..........................................................................12.6.1 Overview 12-22.................................................................................12.6.2 Patching Procedure 12-23................................................................12.6.3 Examples of Loading Patches 12-24................................................

12.7 Maintaining DSP Resources 12-26...........................................................12.7.1 Querying DSP Channel 12-26..........................................................12.7.2 Prohibiting DSP Channel 12-27........................................................

Chapter 13 Alarm Management 13-1...................................................................13.1 Overview 13-1.........................................................................................

13.1.1 Alarm Attributes 13-1......................................................................13.1.2 Alarm Management Contents 13-2.................................................

13.2 Configuring Alarm Management 13-2.....................................................13.2.1 Querying Alarm History Records 13-2............................................13.2.2 Querying Alarm Configuration Information 13-3.............................13.2.3 Setting Alarm Level 13-4................................................................13.2.4 Setting Command Line Terminal Alarm Output 13-4......................13.2.5 Setting Alarm Statistics 13-5...........................................................13.2.6 Setting Alarm Threshold 13-6.........................................................13.2.7 Querying Alarm Statistics 13-6.......................................................13.2.8 Clearing Alarm Statistics 13-7........................................................

13.2.9 Querying Basic Alarm Information 13-7..........................................Chapter 14 Environment Monitoring Configuration 14-1......................................

14.1 Overview 14-1.........................................................................................14.1.1 Composition of Environment Monitoring System 14-1....................14.1.2 Monitored Objects 14-1..................................................................14.1.3 Functions of Environment Monitoring Module 14-1........................

14.2 Connection of Environment Monitoring Hardware 14-2..........................14.3 Environment Monitoring Configuration 14-2............................................

14.3.1 Configuring EMU 14-2....................................................................14.3.2 Configuring H302ESC 14-5............................................................14.3.3 Configuring H303ESC 14-5............................................................

14.4 Configuration Examples 14-7..................................................................Chapter 15 Narrowband Subscriber Test 15-1.....................................................

15.1 Test Group and Test Parameter Configuration 15-1...............................15.1.1 Managing Test Group 15-1.............................................................15.1.2 Setting External Line Test Criteria 15-3..........................................15.1.3 Setting Resistance Adjustment Value in External Line Test 15-4...15.1.4 Setting Test Timeout Control Parameter 15-5................................

15.2 Analog Subscriber Test 15-5...................................................................15.2.1 External Line Test of Analog Subscriber 15-6................................15.2.2 Internal Line Test of Analog Subscriber 15-7.................................15.2.3 Meter-Aided Test of Analog Subscriber 15-9..................................

15.3 ISDN Subscriber Test 15-10.....................................................................15.3.1 Internal Line Test of ISDN Subscriber 15-10....................................15.3.2 ISDN Terminal Test 15-11................................................................15.3.3 External Line Test of ISDN Subscriber 15-12...................................15.3.4 Port Switchover Test of ISDN Subscriber 15-13...............................15.3.5 Meter-aided Test of ISDN Subscriber 15-15.....................................

15.4 TSS Test 15-15.........................................................................................15.4.1 TSS Self-Test 15-15.........................................................................15.4.2 TSS State Query Test 15-16............................................................

15.5 Subscriber Line Test 15-17.......................................................................

Part IV AppendixAppendix A Abbreviations and Acronyms A-1....................................................

HUAWEI

1. Basic Configuration

2. Service Application

3. Maintenance Guide

4. Appendix

HONET UA5000 Universal Access Unit Operation Manual PVM Volume

V100R007

HONET UA5000 Universal Access Unit

Operation Manual PVM Volume

Manual Version T2-051678-20041015-C-1.70

Product Version V100R007

BOM 31161178

Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. Please feel free to contact our local office or company headquarters.

Huawei Technologies Co., Ltd.

Address: Administration Building, Huawei Technologies Co., Ltd.,

Bantian, Longgang District, Shenzhen, P. R. China

Postal Code: 518129

Website: http://www.huawei.com

Email: [email protected]

Copyright 2004 Huawei Technologies Co., Ltd.

All Rights Reserved

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks

, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess, ETS, DMC,

TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, M900/M1800, TELESIGHT, Quidview, Musa, Airbridge, Tellwin, Inmedia, VRP, DOPRA, iTELLIN, HUAWEI OptiX, C&C08 iNET, NETENGINE, OptiX, iSite, U-SYS, iMUSE, OpenEye, Lansway, SmartAX, infoX, TopEng are trademarks of Huawei Technologies Co., Ltd.

All other trademarks mentioned in this manual are the property of their respective holders.

Notice

The information in this manual is subject to change without notice. Every effort has been made in the preparation of this manual to ensure accuracy of the contents, but all statements, information, and recommendations in this manual do not constitute the warranty of any kind, express or implied.

About This Manual

Release Notes

This manual applies to the HONET UA5000 Universal Access Unit V100R007 (referred to as the UA5000 hereinafter).

Organization

This manual consists of four parts, as follows.

z Part I Basic Configuration: This part describes basic knowledge about the UA5000. It is the foundation for service configuration.

z Part II Service Application: This part introduces some major applications of the UA5000. It uses examples to illustrate the whole process of the service configuration.

z Part III Maintenance Guide: This part discusses the daily maintenance management of the UA5000. The content of this part includes necessary maintenance operations, how to conduct maintenance operation, and what commands to be used in the maintenance operation. It is a guide to the maintenance operation activities.

z Part IV Appendix: The appendix includes a list of abbreviations and acronyms used in this manual.

Intended Audience

The manual is intended for the following readers:

z UA5000 Administrators z UA5000 Maintenance Technicians

Conventions

The manual uses the following conventions:

I. General conventions

Convention Description

Arial Normal paragraphs are in Arial.


Arial Narrow Warnings, Cautions, Notes and Tips are in Arial Narrow.

Boldface Headings are in Boldface.

Courier New Terminal Display is in Courier New.

II. Command conventions


Boldface The keywords of a command line are in Boldface.

italic Command arguments are in italic.

[ ] Items (keywords or arguments) in square brackets [ ] are optional.

{ x | y | ... } Alternative items are grouped in braces and separated by vertical bars. One is selected.

[ x | y | ... ] Optional alternative items are grouped in square brackets and separated by vertical bars. One or none is selected.

{ x | y | ... } * Alternative items are grouped in braces and separated by vertical bars. A minimum of one or a maximum of all can be selected.

[ x | y | ... ] * Optional alternative items are grouped in square brackets and separated by vertical bars. Many or none can be selected.

III. Symbols

Eye-catching symbols are also used in the manual to highlight the points worthy of special attention during the operation. They are defined as follows:

Caution: Means reader be extremely careful during the operation.

Note: Means a complementary description.

Operation Manual PVM Volume HONET UA5000 Universal Access Unit Table of Contents

i

Table of Contents

Manual Guide ..................................................................................................................................... i Overview .......................................................................................................................................i Control Boards and Related Operation Manuals..........................................................................i Service Configuration................................................................................................................... ii

Part I Basic Configuration

Chapter 1 Connecting to the System .......................................................................................... 1-1 1.1 Connecting to the System Through Local Serial Port........................................................ 1-1

1.1.1 Connecting Serial Port Cable.................................................................................. 1-1 1.1.2 Running the HyperTerminal .................................................................................... 1-1 1.1.3 Setting up Terminal Communication Parameters ................................................... 1-2 1.1.4 Setting up Terminal Type ........................................................................................ 1-3 1.1.5 Setting up Line Delay and Character Delay............................................................ 1-4 1.1.6 Log in to the System ............................................................................................... 1-5

1.2 Connecting to the System Through Remote Serial Port ................................................... 1-5 1.2.1 Setting up the Called Modem.................................................................................. 1-6 1.2.2 Setting up the Calling Modem................................................................................. 1-7 1.2.3 Setting up Configuration Environment .................................................................... 1-8 1.2.4 Running the HyperTerminal .................................................................................... 1-8 1.2.5 Logging in to the System......................................................................................... 1-9

1.3 Connecting to the System Through Telnet Terminal ......................................................... 1-9 1.3.1 Setting up Configuration Environment .................................................................. 1-10 1.3.2 Run Telnet Application .......................................................................................... 1-10 1.3.3 Logging in to the System....................................................................................... 1-11

Chapter 2 Getting Started with CLI.............................................................................................. 2-1 2.1 Command Line Operation Characteristics......................................................................... 2-1

2.1.1 Intelligent Matching ................................................................................................. 2-1 2.1.2 Editing Characteristics ............................................................................................ 2-1 2.1.3 Character Meaning.................................................................................................. 2-2 2.1.4 Command Mode...................................................................................................... 2-3

2.2 Basic Operations of the CLI............................................................................................... 2-5 2.2.1 Setting Online Help Mode ....................................................................................... 2-5 2.2.2 Setting Interactive Input Mode ................................................................................ 2-7 2.2.3 Setting Screen Scrolling Mode................................................................................ 2-7 2.2.4 Changing Display Language................................................................................... 2-8 2.2.5 Setting Command Echo Display ............................................................................. 2-8 2.2.6 Clearing Terminal Screen ....................................................................................... 2-9


ii

2.2.7 Setting Terminal Type ............................................................................................. 2-9 2.2.8 Setting Terminal Timeout Exit ................................................................................. 2-9 2.2.9 Holding Terminal ................................................................................................... 2-10 2.2.10 Querying History Commands.............................................................................. 2-11 2.2.11 Configuring Host Name....................................................................................... 2-11 2.2.12 Setting System Time ........................................................................................... 2-11 2.2.13 Connectivity Test Commands ............................................................................. 2-11

Chapter 3 Managing a User .......................................................................................................... 3-1 3.1 Overview............................................................................................................................ 3-1 3.2 User Management ............................................................................................................. 3-2

3.2.1 Adding a User.......................................................................................................... 3-2 3.2.2 Deleting a User........................................................................................................ 3-3

3.3 User Attributes Modification............................................................................................... 3-3 3.3.1 Modifying User Authority ......................................................................................... 3-3 3.3.2 Modifying User Password ....................................................................................... 3-4 3.3.3 Modifying User Reenter Number............................................................................. 3-4 3.3.4 Modifying User Attached Information...................................................................... 3-4 3.3.5 Querying a User ...................................................................................................... 3-4 3.3.6 Disconnecting a Login User .................................................................................... 3-5

Chapter 4 Managing System Output Information ...................................................................... 4-1 4.1 Overview............................................................................................................................ 4-1 4.2 Controlling the Output to CLI terminal ............................................................................... 4-1

4.2.1 Querying the Command Line Client Information..................................................... 4-2 4.2.2 Set the infoswitch of a CLI Terminal ....................................................................... 4-2 4.2.3 Querying the infoswitch of a CLI Terminal .............................................................. 4-2 4.2.4 Setting the infolevel of a CLI Terminal .................................................................... 4-2 4.2.5 Querying the Control Level for Information Output to CLI Terminal ....................... 4-3

4.3 Controlling the Output to NMS Terminal............................................................................ 4-3 4.3.1 Setting the infoswitch of an NMS Terminal ............................................................. 4-3 4.3.2 Querying the infoswitch of an NMS Terminal.......................................................... 4-3 4.3.3 Setting the infolevel of an NMS Terminal................................................................ 4-3 4.3.4 Querying the infolevel of an NMS Terminal ............................................................ 4-4

4.4 Controlling the Output to Log Host Terminal ..................................................................... 4-4 4.4.1 Setting the infoswitch of a Log Host Terminal......................................................... 4-4 4.4.2 Querying the infoswitch of a Log Host Terminal ..................................................... 4-4 4.4.3 Setting the infolevel of a Log Host Terminal ........................................................... 4-4 4.4.4 Querying the infolevel of a Log Host Terminal........................................................ 4-5

Chapter 5 NMS Configuration ...................................................................................................... 5-1 5.1 Configuring PVM Network Interfaces ................................................................................ 5-1

5.1.1 Configuring the Network Interface Address ............................................................ 5-1 5.1.2 Configuring the Route ............................................................................................. 5-1


iii

5.2 Configuring an NMS Workstation ...................................................................................... 5-1 5.2.1 Adding an NMS Workstation ................................................................................... 5-1 5.2.2 Activating an NMS Workstation............................................................................... 5-2 5.2.3 Querying NMS Workstation Parameters................................................................. 5-2 5.2.4 Deactivating an NMS Workstation .......................................................................... 5-3 5.2.5 Deleting an NMS Workstation................................................................................. 5-3 5.2.6 Modifying an NMS workstation................................................................................ 5-3 5.2.7 Managing NMS Terminal Output Control................................................................ 5-4

5.3 Configuration Examples..................................................................................................... 5-4

Chapter 6 Frame Configuration ................................................................................................... 6-1 6.1 Configuring a Frame .......................................................................................................... 6-1

6.1.1 Adding a frame........................................................................................................ 6-1 6.1.2 Deleting a frame...................................................................................................... 6-2

6.2 Configuring an Inter-frame Link ......................................................................................... 6-2 6.2.1 Adding an Inter-frame Link...................................................................................... 6-2 6.2.2 Querying an Inter-frame Link .................................................................................. 6-3 6.2.3 Delete an inter-frame link ........................................................................................ 6-4

6.3 Configuring Frame Attributes............................................................................................. 6-4 6.3.1 Configuring Frame Attributes .................................................................................. 6-5 6.3.2 Configuring EMU of Frame ..................................................................................... 6-5 6.3.3 Querying Frame Attributes ...................................................................................... 6-5

Chapter 7 Board Configuration.................................................................................................... 7-1 7.1 Overview............................................................................................................................ 7-1 7.2 Configuring a Board........................................................................................................... 7-1

7.2.1 Querying Board Information .................................................................................... 7-1 7.2.2 Adding a Board........................................................................................................ 7-3 7.2.3 Confirming a Board ................................................................................................. 7-3 7.2.4 Deleting a Board ..................................................................................................... 7-4 7.2.5 Prohibiting/Unprohibiting a Board ........................................................................... 7-4

7.3 Querying Board Version .................................................................................................... 7-5 7.4 Querying Board CPU Usage.............................................................................................. 7-5 7.5 Resetting a Board .............................................................................................................. 7-5

Part II Service Application

Chapter 8 MG Interface Configuration ........................................................................................ 8-1 8.1 Overview............................................................................................................................ 8-1 8.2 MG Interface Configuration................................................................................................ 8-1

8.2.1 Adding an MG Interface .......................................................................................... 8-1 8.2.2 Starting/Closing an MG Interface............................................................................ 8-1 8.2.3 Deleting an MG Interface ........................................................................................ 8-2 8.2.4 Configuring MG Interface Protocol Parameter........................................................ 8-2


iv

8.2.5 Configuring Dual Homing ........................................................................................ 8-4 8.2.6 Configuring MGC Forced Switchover...................................................................... 8-4 8.2.7 Configuring Equipment Authentication.................................................................... 8-4 8.2.8 Querying MG Interface Information......................................................................... 8-5 8.2.9 Configuring MGCP Stack Parameter ...................................................................... 8-6 8.2.10 Configuring H.248 Stack Parameter ..................................................................... 8-8 8.2.11 Configuring Ringing Mapping Entry ...................................................................... 8-9 8.2.12 Configuring MG Interface Software Parameters ................................................. 8-11 8.2.13 Configuring System Parameters ......................................................................... 8-13 8.2.14 Configuring A/ Law............................................................................................ 8-15 8.2.15 Configuring SNTP Client ..................................................................................... 8-16 8.2.16 Configuring DNS Client ....................................................................................... 8-16

Chapter 9 Narrowband Subscriber Configuration ..................................................................... 9-1 9.1 Adding a Narrowband Subscriber...................................................................................... 9-1

9.1.1 Adding a single MG subscriber ............................................................................... 9-1 9.1.2 Adding a batch of MG subscribers .......................................................................... 9-1

9.2 Deleting a Narrowband Subscriber.................................................................................... 9-2 9.3 Modifying the Narrowband Subscriber Data...................................................................... 9-2 9.4 Setting Port Gain, Pulse Dial and Polarity Reversal for Narrowband Subscriber ............. 9-2 9.5 Setting 16/12KC Attribute of Narrowband Subscriber Port ............................................... 9-3 9.6 Querying Narrowband Subscriber ..................................................................................... 9-4 9.7 Terminating/Restarting Narrowband Subscriber Port Service........................................... 9-5

Chapter 10 SPC Configuration................................................................................................... 10-1 10.1 Overview........................................................................................................................ 10-1 10.2 Configuring an SPC ....................................................................................................... 10-1

10.2.1 Adding an SPC.................................................................................................... 10-1 10.2.2 Deleting an SPC.................................................................................................. 10-3 10.2.3 Querying an SPC ................................................................................................ 10-3 10.2.4 Releasing SPC.................................................................................................... 10-3 10.2.5 Setting up SPC.................................................................................................... 10-4 10.2.6 Modifying SPC Parameter................................................................................... 10-4

Chapter 11 Application of Voice Service .................................................................................. 11-1 11.1 Overview........................................................................................................................ 11-1 11.2 Voice Service Configuration .......................................................................................... 11-1

11.2.1 Networking and Data Explanation....................................................................... 11-1 11.2.2 Configuring Data ................................................................................................. 11-4

Part III Maintenance Guide

Chapter 12 System Maintenance ............................................................................................... 12-1 12.1 Overview........................................................................................................................ 12-1

12.1.1 System Management Files and Storage Media .................................................. 12-1


v

12.1.2 Upgrade Procedures for System with One Control Board .................................. 12-1 12.1.3 Upgrade Procedures for System with Two Control Boards ................................ 12-2

12.2 Managing System Data ................................................................................................. 12-4 12.2.1 Saving Data......................................................................................................... 12-4 12.2.2 Duplicating Data.................................................................................................. 12-5 12.2.3 Backing up Data.................................................................................................. 12-5 12.2.4 Erasing Data........................................................................................................ 12-6

12.3 System Switchover ........................................................................................................ 12-7 12.3.1 Setting Data Synchronization Switch .................................................................. 12-7 12.3.2 Querying Data Synchronization State................................................................. 12-8 12.3.3 Manual Switchover.............................................................................................. 12-8

12.4 Loading Software........................................................................................................... 12-9 12.4.1 Setting FTP User Name and Password .............................................................. 12-9 12.4.2 Power-on Loading ............................................................................................... 12-9 12.4.3 Loading BIOS File Online.................................................................................. 12-14 12.4.4 Loading Host Program File Online.................................................................... 12-15 12.4.5 Loading Host Database File Online .................................................................. 12-19 12.4.6 Loading Multi-Language Resource File Online................................................. 12-20 12.4.7 Host Version Rollback....................................................................................... 12-21

12.5 Managing Logs ............................................................................................................ 12-21 12.5.1 Setting Log Host................................................................................................ 12-21 12.5.2 Querying Log..................................................................................................... 12-22

12.6 Managing Patches ....................................................................................................... 12-22 12.6.1 Overview ........................................................................................................... 12-22 12.6.2 Patching Procedure........................................................................................... 12-23 12.6.3 Examples of Loading Patches........................................................................... 12-24

12.7 Maintaining DSP Resources........................................................................................ 12-26 12.7.1 Querying DSP Channel..................................................................................... 12-26 12.7.2 Prohibiting DSP Channel .................................................................................. 12-27

Chapter 13 Alarm Management.................................................................................................. 13-1 13.1 Overview........................................................................................................................ 13-1

13.1.1 Alarm Attributes................................................................................................... 13-1 13.1.2 Alarm Management Contents ............................................................................. 13-2

13.2 Configuring Alarm Management.................................................................................... 13-2 13.2.1 Querying Alarm History Records......................................................................... 13-2 13.2.2 Querying Alarm Configuration Information.......................................................... 13-3 13.2.3 Setting Alarm Level ............................................................................................. 13-4 13.2.4 Setting Command Line Terminal Alarm Output .................................................. 13-4 13.2.5 Setting Alarm Statistics ....................................................................................... 13-5 13.2.6 Setting Alarm Threshold...................................................................................... 13-6 13.2.7 Querying Alarm Statistics.................................................................................... 13-6 13.2.8 Clearing Alarm Statistics ..................................................................................... 13-7


vi

13.2.9 Querying Basic Alarm Information ...................................................................... 13-7

Chapter 14 Environment Monitoring Configuration ................................................................ 14-1 14.1 Overview........................................................................................................................ 14-1

14.1.1 Composition of Environment Monitoring System................................................ 14-1 14.1.2 Monitored Objects ............................................................................................... 14-1 14.1.3 Functions of Environment Monitoring Module..................................................... 14-1

14.2 Connection of Environment Monitoring Hardware......................................................... 14-2 14.3 Environment Monitoring Configuration .......................................................................... 14-2

14.3.1 Configuring EMU................................................................................................. 14-2 14.3.2 Configuring H302ESC......................................................................................... 14-5 14.3.3 Configuring H303ESC......................................................................................... 14-5

14.4 Configuration Examples................................................................................................. 14-7

Chapter 15 Narrowband Subscriber Test ................................................................................. 15-1 15.1 Test Group and Test Parameter Configuration ............................................................. 15-1

15.1.1 Managing Test Group ......................................................................................... 15-1 15.1.2 Setting External Line Test Criteria ...................................................................... 15-3 15.1.3 Setting Resistance Adjustment Value in External Line Test............................... 15-4 15.1.4 Setting Test Timeout Control Parameter ............................................................ 15-5

15.2 Analog Subscriber Test ................................................................................................. 15-5 15.2.1 External Line Test of Analog Subscriber............................................................. 15-6 15.2.2 Internal Line Test of Analog Subscriber.............................................................. 15-7 15.2.3 Meter-Aided Test of Analog Subscriber .............................................................. 15-9

15.3 ISDN Subscriber Test .................................................................................................. 15-10 15.3.1 Internal Line Test of ISDN Subscriber .............................................................. 15-10 15.3.2 ISDN Terminal Test........................................................................................... 15-11 15.3.3 External Line Test of ISDN Subscriber ............................................................. 15-12 15.3.4 Port Switchover Test of ISDN Subscriber ......................................................... 15-13 15.3.5 Meter-aided Test of ISDN Subscriber ............................................................... 15-15

15.4 TSS Test ...................................................................................................................... 15-15 15.4.1 TSS Self-Test .................................................................................................... 15-15 15.4.2 TSS State Query Test ....................................................................................... 15-16

15.5 Subscriber Line Test.................................................................................................... 15-17

Part IV Appendix

Appendix A Abbreviations and Acronyms .................................................................................A-1

Operation Manual PVM Volume HONET UA5000 Universal Access Unit Manual Guide

i

Manual Guide

Note: In this guide, the configuration of the UA5000 takes UAM for example unless otherwise stated.

Overview

The internal multi-bus technology enables the UA5000 universal access unit to provide integrated access to both broadband and narrowband services.

The UA5000 can network with the MD5500 to form the HONET integrated service access system. It also can access the PSTN in the form of single-layer networking.

As a remote device, the UA5000 meets all kinds of access requirement by supporting board intermixing, including POTS, ISDN, DDN and xDSL (ADSL/VDSL/SHDSL).

The UA5000 provides different upstream ports to access the narrowband or the broadband network:

z Provide STM-4 ATM optical port, STM-1 ATM optical port and IMA E1 port for access to the ATM backbone network.

z Provide FE/GE port for access to the IP network. In addition, it uses the VoIP technology to carry voice services over the IP packet-based network.

z Provide V5 and E1 interfaces for access to the narrowband network such as the PSTN and DDN.

The integrated access function is accomplished by the double control boards of the UA5000. One is the broadband control board, while the other the narrowband. The service configuration of the UA5000 differs with control boards. For specific configuration, refer to relevant operation manual.

Control Boards and Related Operation Manuals

Table 1 shows the type and name of the control board of the UA5000 and the corresponding operation manual.


ii

Table 1 Control boards and related operation manuals

Control Board Type Control Board Operation Manual

ATM service processing boardAPM HONET UA5000 Universal Access Unit Operation Manual APM Volume Broadband control board IP service processing boardIPM HONET UA5000 Universal Access Unit Operation Manual IPM Volume

Packet-based voice processing boardPVM


V5 interface processing unitPVU HONET UA5000 Universal Access Unit Operation Manual PVU Volume V5 protocol processing board and control boardPV8/PV4

HONET MD5500 Multi-service Distribution Module Operation Manual Narrowband

control board

Remote subscriber processing boardRSP

HONET MD5500 Multi-service Distribution Module Operation Manual HONET UA5000 Universal Access Unit Operation Manual PVU Volume HONET UA5000 Universal Access Unit Operation Manual PVM Volume

This manual focuses on the narrowband service configuration of the UA5000 with the PVM as its control board.

Service Configuration

The UA5000 provides the Voice over IP (VoIP) service for subscribers through its narrowband control board PVM. Figure 1 shows the typical networking.

MGCP

Loghost

H.248

SoftSwitch

WAN

UA5000UA5000

iManager N2000

Router Router

Figure 1 UA5000 networking

Figure 2 shows the service configuration procedure of the UA5000. For details, refer to the relevant chapters of this manual.


iii

Connecting to the systemChapter 1

Managing a User Chapter 3

NMS Configuration Chapter 5

Frame ConfigurationChapter 6

Board ConfigurationChapter 7

MG Interface ConfigurationChapter 8

SPC ConfigurationChapter 9

Narrowband SubscriberConfiguration Chapter 9

Start

End

Figure 2 Configuration procedure of UA5000 services

HUAWEI


Part I Basic Configuration

Operation Manual PVM Volume HONET UA5000 Universal Access Unit Chapter 1 Connecting to the System

1-1

Chapter 1 Connecting to the System

The UA5000 universal access unit supports local maintenance and remote maintenance. The local maintenance uses the serial port or Telnet mode. The remote maintenance uses the modem dialing or Telnet mode.

This chapter includes:

z Connecting to the System Through Local Serial Port z Connecting to the System Through Remote Serial Port z Connecting to the System Through Telnet Terminal

1.1 Connecting to the System Through Local Serial Port In the serial port mode, you can connect the PC to the UA5000 using the HyperTerminal of the Windows operating system. The following introduces how to connect the PC to the system through the local serial port. Take Windows 98 as an example.

1.1.1 Connecting Serial Port Cable

Connect the PC serial port to the COM serial port in the control board by a standard RS-232 serial port cable. See Figure 1-1.

Serial port COMPC

Control board

UA5000

RS-232 serialport cable

LANWAN

Figure 1-1 Setting up the configuration environment through the local serial port

1.1.2 Running the HyperTerminal

Select the menu [Start/Programs/Accessories/Communications/HyperTerminal] on the PC to run HyperTerminal program. After that, create the corresponding serial port connection. See Figure 1-2.


1-2

Figure 1-2 Selecting the connection serial port number

Suppose the serial port is port 1.

1.1.3 Setting up Terminal Communication Parameters

Set the communication parameters as follows:

z Baud rate: 9600 bit/s z Data bits: 8 z Stop bits: 1 z Parity: none z Flow control: none

The baud rate here must be consistent with that of the UA5000. By default, it is 9600 bit/s. See Figure 1-3.


1-3

Figure 1-3 Setting the terminal communication parameters

Note: Inconsistent setting of baudrate often causes illegible display of characters on the terminal. If this happens after you log in to the system, select another baudrate from the following for the terminal: 9600 bit/s, 19200 bit/s, 38400 bit/s, 57600 bit/s and 115200 bit/s.

1.1.4 Setting up Terminal Type

Select the menu [File/Properties] in the HyperTerminal to set the terminal emulation type as ANSI or Auto detect. See Figure 1-4.


1-4

Figure 1-4 Setting the terminal type

Note: z By default, the terminal type of the UA5000 is ANSI. z Use the show terminal type command to query the terminal type. z Use the terminal type {ansi | vt100} command to modify the terminal type of the system.

1.1.5 Setting up Line Delay and Character Delay

Click [ASCII Setup] to set all kinds of parameters. See Figure 1-5.


1-5

Figure 1-5 Setting the ASCII codes

Note: The "character delay controls how fast a character in a text is pasted to the HyperTerminal, while the line delay controls the time interval of each line. Insufficient time delay will lead to loss of characters. If it is abnormal during pasting texts, modify this value.

1.1.6 Log in to the System

After setting the parameters, press , and the HyperTerminal console displays the following information:

>>User name:

Enter the user name and password to log in to the UA5000. The default administrator is root, and its password is admin.

1.2 Connecting to the System Through Remote Serial Port To perform remote maintenance through a serial port connection, it is required to connect an external modem at the UA5000 side. See Figure 1-6 for the networking.


1-6

Called modem

UA5000

COM

PSTN

LINEport

Serial portCOM

Control board

Calling modem PC

PSTN

Serial portLINEport

LANWAN

Figure 1-6 Setting up the configuration environment through the remote serial port

In this mode, there are the following requirements on the modem.

z Both the calling and called modems are the standard modems and support the AT command set.

z The called modem shall be an external modem. z The calling modem connected to the maintenance PC can be either an external

modem or a built-in one. In general, use the calling modem from the same manufacturer as the called modem.

The following will describe one type of modem. Refer to the AT commands in practical for the modem configuration.

1.2.1 Setting up the Called Modem

The UA5000 communicates with the called modem only through SD, RD and SG leads of the serial port cable. Therefore, it is required to mask the handshake and flow control signals of the modem.

Before configuring the modem, you should connect an intelligent terminal to it. The following is a sample modem configuration using the HyperTerminal.

1) Connect the modem with the PC through a serial port cable. 2) Connect the power cord and then turn on the modem. 3) Install the modem driver in the operating system (this step is optional). 4) Run the HyperTerminal and select COM1 for connection. Suppose that the

modem is connected to COM1. 5) Set the HyperTerminal as follows: 9600 for baud rate, 8 for data bits, none for

parity, 1 for stop bits and none for flow control.


1-7

Note: If there is no display on the terminal after the connection is set up, check whether the no echo display function of the modem has been enabled at the previous setting. Enter the AT&F command to restore the default setting for the modem. After that, there will be echo display in the terminal.

6) Check if the modem works normally.

Run the AT&F command in the HyperTerminal to restore the default setting of the modem. See whether the status code OK is displayed on the screen. If yes, the modem is working normally.

7) Enter the following commands in the HyperTerminal.

ATS0=1 //Set automatic answering (ringing once).

AT&D //Ignore DTR signal.

AT&K0 //Disable flow control.

AT&R1 //Ignore RTS signal.

AT&S0 //Force DSR at a higher level.

ATEQ1&W //Disable the modem from returning command response and execution result, and save the configuration.

Note: z After the execution of the previous command, there will be no echo characters or command execution

result displayed on the screen for any AT commands. Generally, many modems can work normally as required without any configuration after power on.

z Due to modems rate restriction, usually set the serial port rate of the UA5000 as 9600 bit/s or 19200 bits. If necessary, use the baudrate command to modify it. Moreover, to avoid the rather high line rate between modems, you can run the AT$MB=9600 (or another value) command to limit the highest rate between modems before the execution of the ATEQ1&W command.

1.2.2 Setting up the Calling Modem

In general, the calling modem can run normally without any configuration after power on. If the cable connecting the maintenance terminal with the modem is different from that used in the standard serial port, mask the handshake and flow control signals of the modem before the connection is created.

The setting details are the same as those of the called modem.


1-8

1.2.3 Setting up Configuration Environment

Set up the configuration environment as shown in Figure 1-6.

1) Connect the called modem

Connect the telephone line to the LINE port of the called modem. Connect the serial port of the modem with COM in the control board using the serial port cable for the UA5000. Turn on the modem.

2) Connect the calling modem

For the external modem, connect the telephone line to its LINE port. Connect the serial port of the modem with the serial port of the maintenance terminal using the serial port cable for the modem. Turn on the modem.

For the built-in modem, connect the telephone line to its LINE port.

1.2.4 Running the HyperTerminal

I. For the external modem

Refer to 1.1 Connecting to the System Through Local Serial Port for details.

The procedure is as follows.

1) Run the HyperTerminal. 2) Select the serial port number according to the actual connection. 3) Set the communication parameters as follows: 9600 for baud rate, 8 for data bits, 1

for stop bits, none for parity and none for flow control.

Note: Do not select modem in the Connect using drop down list to set up the connection. Select Direct to Com x, because the HyperTerminal often fails to initialize the modem normally.

4) In the HyperTerminal window, use an AT command to dial a number such as ATDT xxxxxxxx and then press . xxxxxxxx is the telephone number used for the telephone line of the remote modem connected with the host.

Refer to the AT command set for detailed dialing commands. For example, ATDT0 W 555XXXXXXXX means that the HyperTerminal dials external line 0 at first, waits for exchange to send external line dial tone, and then dials the number 555XXXXXXXX.

II. For the built-in modem

The procedure is as follows.

1) Run the HyperTerminal. 2) Set the called number.


1-9

3) Select the modem in the Connect using drop down list. 4) Click in the properties setting page to configure the modem

properties. 5) Select Bring up terminal window after dialing in the Options tab of the

properties setting page. 6) Click to confirm the setting. 7) Click to proceed with the dialing.

You do not have to use the ATDT command for the dialing.

1.2.5 Logging in to the System

After the dialing, the OH and RI indicators of the modem connected with the PC will light. In addition, the modem will give sound.

After the dialing is connected, the CD indicators (carrier detect) of both modems will light. In addition, a result code "CONNECT9600" (or CONNECT19200) will be displayed on the HyperTerminal window. Now the connection between the two modems is successful.

If the result code "NO CARRIER" is returned, it indicates that the connection fails. In this case, check the hardware connection lines and telephone line.

Press several times continuously, a login command line interface will appear.

After the remote equipment configuration, use the disconnection command of the HyperTerminal to release the connection.

Caution:

z The call will be disconnected if you press any key after the dialing and before the modem connection is succeeded.

z After the remote maintenance completes, do release the modem connection before you close the HyperTerminal. Otherwise, the remote modem of some type will remain online all the time, and the next dialing connection will fail.

1.3 Connecting to the System Through Telnet Terminal If you have already set the outband NMS interface or inband NMS interface of the UA5000 correctly, you can log in to the UA5000 by the Telnet through the Local Area Network (LAN), Wide Area Network (WAN).


1-10

1.3.1 Setting up Configuration Environment

I. Outband management

Configure the IP attributes through the maintenance serial port. The attributes include IP address, subnet mask, gateway and so on.

Note: Ensure the serial port maintenance environment has been set up before you set up the Telnet environment. Moreover, ensure it can work normally, and you can configure the Telnet data through the serial port.

After that, log in to the UA5000 by the Telnet through the LAN or WAN, as shown in Figure 1-7.

PSTN

Workstation

WAN/LAN

UA5000

COM

Control board

LANWAN

Workstation

Maintenanceterminal

Server

Figure 1-7 Setting up the configuration environment through the Telnet

1.3.2 Run Telnet Application

To run the Telnet application on the PC, select [Start/Run].

Select the [Terminal/Preference] menu in the Telnet application interface to set the preference of the Telnet terminal. Set the terminal type as ANSI and the buffer size as 1000.


1-11

Note: The default buffer of the Telnet is rather small. You may enlarge it properly so that more history commands can be shown in one screen. The recommended size of buffer area is 1000 characters.

1.3.3 Logging in to the System

On the interface of the Telnet application, select the [Connect/Remote system] menu, and input the IP address of the UA5000 to set up Telnet session. See Figure 1-8.

Figure 1-8 Setting up Telnet session

Click for connection. After that, you are required to input the user name and password for login. The system supports four concurrent Telnet users. If the system prompts that too many users are online, you can try later. The default administrator is root and the password is admin.

After logging in, you can run the relevant command to configure or check the UA5000. Refer to subsequent chapters for the specific configuration.

Operation Manual PVM Volume HONET UA5000 Universal Access Unit Chapter 2 Getting Started with CLI

2-1

Chapter 2 Getting Started with CLI

This chapter includes:

z Command Line Operation Characteristics z Basic Operations of the CLI

2.1 Command Line Operation Characteristics The command line can be used to implement the management, maintenance and configuration of the UA5000.

Note: z For the command line conventions of this manual, refer to Command Conventions in About This

Manual. z Except for user passwords, the command line inputs are case insensitive.

2.1.1 Intelligent Matching

z Supporting maximum matching of the command

The command line interpreter adopts the incomplete searching method for key words. To obtain a certain interpretation, you need to enter the non-conflicting key words. For example, to obtain the interpretation of the enable command, you can only enter en or ena. enable is the only command that begins with en in this command line system.

z Supporting automatic matching of key words

You can obtain the automatic matching result of the key words by entering incomplete command key words and a space. In this way, you will not have to enter long key words, which greatly facilitates the operation. If the matching is incorrect, you cannot continue entering the next key word or parameter. Therefore, you can always see the complete command spelling format in the command line operation. If you cannot enter a space, it indicates that the input command is incorrect, and you must check and input the correct command.

2.1.2 Editing Characteristics

The command line interface provides basic command editing functions and supports the edition of multiple lines. The maximum length of a command is 255 characters. You can edit the command line through the HyperTerminal or Telnet. The editing functions


2-2

are shown in Table 2-1. For the HyperTerminal, the and are disabled. For other terminals, some keys are disabled.

Table 2-1 Command line editing functions

Key Function

Common key Insert characters to the current cursor position and move the cursor right if the editing buffer is not full.

Delete one character before the cursor position and move the cursor backward. The cursor will stop if reaching the head of the command line. Delete the character at the cursor position. or Move the cursor left by one character. or Move the cursor right by one character.

or Show the history commands. Some terminals do not support these two keys. In this case, use , or , .

Delete all characters before the cursor, and the cursor is located at the head of the line.

Delete all characters after the cursor, and the cursor is located at the end of the line. Move the cursor to the head of the line. Move the cursor to the end of the line. Press it twice to cancel the current input.

2.1.3 Character Meaning

There are some prompting characters in the command line interface. They indicate the parameter type of next command key. See below.

huawei#atmlan arp

{ rfc1483b|ipoa }:ipoa { ip-address }:10.10.1.2

{ frame/slot/port|frame/slot }:0/11/0 { vpi }:0

{ vci }:100 { |rx-cttr }: Table 2-2 shows their meanings.


2-3

Table 2-2 Meaning of characters

Character Meaning

Key word

Enumeration, the following contents are the items to be opted.

ULONG, the following contents are the value range.

LONG, the following contents are the value range.

Character string, the following contents are the length range of input character string.

IP address type

MASK

MAC address

Hexadecimal number, it supports ox, but it supports the decimal number by default.

Date

Time

2.1.4 Command Mode

The command mode is a kind of command encapsulation conception. It is like a container, and all commands belonging to this command mode are taken into this command container.

Table 2-3 shows the functions and characteristics of these various command modes in view of different control boards.

Table 2-3 List of functions and characteristics of various command modes

Command mode Function Mode prompt example Access mode

User mode Query basic system information. UA5000> Enter the mode directly after login.

Privilege mode Conduct basic system configuration. UA5000# UA5000>enable

Global configuration mode

Configure system equipment and global parameters.

UA5000(config)# UA5000#configure terminal

ESL user mode Configure APM board properties and enter the sub-interface mode

UA5000(config-if-apm-0/12)# UA5000(config)#interface apm frame/slot

Narrowband resource configuration mode

Digital signal processor (DSP), channel resource operation

UA5000(config-narrow-resource)#

UA5000(config)#narrow resource


2-4

Command mode Function Mode prompt example Access mode

MG interface mode Configure the parameters and attributes of MG interface

UA5000(config-if-mg-0)# UA5000(config)#interface mg 0

EMU configuration mode

Configure the EMU parameters

UA5000(config-if-h302esc-0)#

UA5000(config)#interface emu 0

Test mode Test group and test parameters configuration UA5000(config-test)# UA5000(config)#test

Note: z Use the exit command to quit the current command mode. Use the end command to enter Privileged

Mode directly. Use the disable command to return to User Mode from Privileged Mode. z The prefix of the mode prompt character is PVU100. It can be modified by the hostname command.

The command mode is indicated in the bracket.

A hierarchical protection mechanism is applied to the command line to prevent unauthorized users from invading the system. In this way, users at different levels can enter different command modes. In addition, even if users at different levels enter the same mode, the commands that can be executed by them will be different.

The command line mode is downward compatible to a certain degree: all commands in user mode can be executed in privileged mode, and all commands in both user mode and privileged mode can be executed in global configuration mode. Some commands as show board and terminal language can be executed in any mode.

See Figure 2-1 for the relationship between the command modes.


2-5

ExitEnable

DisableTest

Narrowband resource

Configureterminal

Interface mg mgid

Interface emu emuid

esl user

Global configurationmode

UA5000(config)#

Privilegemode

UA5000#

Commonuser modeUA5000>

UA5000(config-test)#

UA5000(config-narrow-resource)#

MG interface configuration modeUA5000(config-if-mg-...)#

UA5000(config-if-h302esc-0)#

UA5000(config-esl-user)#

End

Exit

Exit

Exit

Exit

Exit

Exit

EMU configuration mode

Test mode

ESL user configuration mode

Narrowband resourceconfiguration mode

Figure 2-1 Command mode relationship diagram

2.2 Basic Operations of the CLI The basic operations includes:

z Setting Online Help Mode z Setting Interactive Input Mode z Setting Screen Scrolling Mode z Changing Display Language z Setting Command Echo Display z Clearing Terminal Screen z Setting Terminal Type z Setting Terminal Timeout Exit z Holding Terminal z Querying History Commands z Configuring Host Name z Setting System Time z Connectivity Test Commands

2.2.1 Setting Online Help Mode

I. Online help

z Execute the help command to obtain the brief description of the help system. Huawei>help

At any position of the command, input '?' to get help

Two types of help are provided:

z Input ? in the command line to show all commands of the current mode .


2-6

huawei>?

---------------------------------------------

User mode command

---------------------------------------------

clear Clear board or port cell statistics

cls Clear screen

z Input ? after an incomplete command key word to obtain the help information about the current available command key words.

huawei>s?

---------------------------------------------

User mode command

---------------------------------------------

scroll Enable/disable scroll function

show show command group

z Input ? after a complete command key word followed by a space to obtain the brief help and parameters used for the current command.

huawei>show ?

---------------------------------------------

User mode command

---------------------------------------------

alarm Show alarm related information

II. Help mode setting

Use the [no] help-mode command to set whether to redisplay the last input line on the next command prompt line after having obtained online help. Use the help-mode command to enable this function, and the last input line will then be redisplayed on the next line.

huawei#help-mode

Enable input memory function

huawei#configure ?

---------------------------------------------

Privilege mode command

---------------------------------------------

terminal Enter the global configuration mode

huawei#configure //The help switch is enabled. The system will display

the command again after displaying the help information automatically. Then

it will wait for further input of parameters or executing the command.

huawei#no help-mode


2-7

Disable input memory function

huawei#configure ?

---------------------------------------------

Privilege mode command

---------------------------------------------

terminal Terminal configuration operation

huawei# //The help switch is disabled. The system will not display

the command after displaying the help information. To execute the command, you

have to input the command again.

2.2.2 Setting Interactive Input Mode

The system supports interactive input of command. Use the smart command to enable this function. Use the no smart command to disable it. The function is enabled by default.

In the interactive command input mode, after you input the command and press key, the system judges whether the command key words and parameters are complete. If not, the system will prompt you to continue inputting them. Meanwhile, the system will show the range of parameters available for the command being input. The optional parameters will also be prompted. You may press key to ignore them directly.

huawei#smart //Enable the interactive input mode.

huawei#configure

{ terminal }: // Press key after inputting an incomplete command,

and the system will prompt the next parameter name.

If the interactive mode is disabled, after you input a command and press key, the system directly executes this command. Without parameter being entered, the system gives error information.

huawei#no smart //Disable the interactive input mode.

huawei#configure

^

% Incomplete command, and error detected at '^' marker.

// Press key after inputting an incomplete

command, and the system will indicate that the command is incomplete.

2.2.3 Setting Screen Scrolling Mode

If the terminal cannot display all the information in one screen, you can execute the no scroll command to enable the manual screen scrolling function. In this case, you have to scroll the screen manually. If you do not want to query information screen by screen, you can use the scroll command to enable automatic scroll of screens. In this case, the information will be scrolled on the screen automatically.


2-8

By default, the manual screen scrolling function is enabled.

In the manual scrolling mode, if the information to be shown is more than one screen, the following information will be shown on the lower part of the screen.

---- More ( Press Q to break ) ----

You have the following choices:

z Press to show the information line by line. z Press to end the information display. z Press any other key to show the information screen by screen.

If you do not input anything in one minute, the system will end the information display.

2.2.4 Changing Display Language

Use the show language command to query the loaded language and version information.

Use the terminal language command to switch to the other language.

The UA5000 operating system supports two kinds of languages serving as local language and general language respectively. At present, the local language is Chinese and the general language is English.

If both languages are loaded, the default language when the system starts is general language. You can select one language for the information display according to your own language preference.

2.2.5 Setting Command Echo Display

Use the echo command to enable the command echo display. Use the no echo command to disable the function. If the function of command echo display is disabled, the local response function of the terminal must be enabled. Otherwise, no input command will be displayed on it.

By default, this function is enabled, while the local response function of the terminal is disabled.

If the input character is displayed twice on the terminal, the local echo function of the terminal must be disabled. Do as follows.

z For HyperTerminal, select [file/properties/Settings/ASCII Setup]. In that page, uncheck Echo typed characters locally.

z For a Telnet terminal, select to pop up a setting page. Uncheck Local Echo in that page.


2-9

2.2.6 Clearing Terminal Screen

Use the cls command to clear the screen. After the execution of this command, the current content on the screen is cleared, and the command input prompt appears on the upper left of the screen. It clears only the screen display, but not the screen buffer.

2.2.7 Setting Terminal Type

Use the terminal type {ansi|vt100} command to set the terminal type. Then use the show terminal type command to show the terminal type.

For example, to set the terminal type as VT100, and query the operation result, do as follows.

huawei#terminal type vt100

huawei#show terminal type

Terminal type: VT100

Different terminals have different terminal editing characteristics. To be compatible with most terminals, the terminals are divided into two types: standard terminal (ANSI) and VT series terminals. The terminal type of the command system must be configured correctly acc

Documents

UA5000 Operation Manual-PVM Volume.pdf