12
MA U AXIF ULTR FLO RASO ( TM ONIC (Ser C FL ries LOW MU) Se MET ) eil Ente TER erprise S e Co.

U LTRASO NIC FLOW METERS Series MU) - MaxiFlomaxiflo.co.kr/Cat-Manual/Catalog_Ultrasonic.pdf · MAXIFLO® MU series measures flow and does much more For the measurement, two ultrasonic

  • Upload
    danganh

  • View
    219

  • Download
    0

Embed Size (px)

Citation preview

MA

U

AXIF

ULTR

FLO

RASO(

TM

ONIC(Ser

C FLries

LOW MU)

Se

MET)

eil Ente

TER

erprise

S

e Co.

Flo

Tr

2

ow Co

Handhel(MU-HA

ransd

ompu

d A)

ducer

Clamp

uters

Portab(MU-P

rs

p-on

ble O)

I

Ultr

Wall(MU

nsertion

a-clean

Mount U-WA)

n

Micro-F

Pa(

Full Bor

low Sen

anel Mount(MU-PA)

re

nsor

t

MAXIFLO® MU series measures flow anddoes much more

For the measurement, two ultrasonic pulses are sent through the medium, one in flow direction, and the other against it. The transducers are alternatively working as emitter and receiver.

The transit time of the ultrasonic signal propagating in flow direction is shorter than the transit time of the signal propagating against flow direction. The transit-time difference Δt is measured and allows the determination of the average flow velocity on the propagation path of the ultrasonic signals. A profile correction is performed to obtain the average flow velocity on the cross-section of the pipe, which is proportional to the volume flow.

3

Transit-Time Technology The flowmeter technology employed by our MU series is called “Transit-time” ultrasonic technology. It is also called “time-of-flight” or “time-difference” ultrasonic technology. In this technology, one of the keys to the precision performance is its transmission and reception technology. Transit-time provides an innovative direct ultrasonic transmission technique that ensures reliable and accurate signal detection for a wide range of processes.

Working Principle of Transit-Time Technology

Non-Invasive, Clamp-on Transducers Since ultrasounds propagate in solids, the transducers can be mounted onto the pipe. The measurement is therefore non-invasive, and no cutting of pipes is necessary for the installation of the transducers. Because with just 3 sets of transducers, pipes ranging from 15mm to 6000mm can be covered, the ownership cost doesn’t increase as the pipe size increases, which is the decisive cost saving factor as compared to traditional flowmeters. Single-Board Solution – A Decisive Cost Saver All the main elements such as power supply, transducer, computation, communication, etc. are integrated into one single board. This allows MU series much more accessible to users that are sensitive about purchase and maintenance budgets.

4

Ex

Wall Mou(MU-WA

Panel Moun(MU-PA)

x-Proof Enc

nt A)

nt

losure

DeCo

MU seriesconfigurevarious aThe Wall the Panefull functmounted (clamp-o(insertionultrasonicprovide aultrasonicined withtraditiona MU seriestages in cication vebe matchsingle meFrom higease of inare the bfaced witrequire:

High High

with Low o No pr Low p Diver

edicatontinuo

s flow comped flexibly tapplication Mount (MUl Mount (Mion, perma non-intrusn) or intrusn and full-bc flowmeteall the benec technolog

h the perforal meters.

s offers macapabilitiesersatility thhed by any etering techh performanstallation, best choice th applicatio

precision reliability clow mainte

ownership cressure dropower consse interface

ted/Fous Acc

puters are to cater to needs. U-WA) and U-PA) are nently

sive sive bore) rs that

efits of gy comb-rmance of

any advan-s and appl-hat cannot other hnology. ance to MU series when on that

combined enance cost p umption es

Fixed Curacy,

MU seand osite isotherhumito cocenteversacommno loalso a MU-Win expopera Ultrasbecomchoicat Semeet everythe riwherelimitabenefmete

ConfigVerifia

eries providoutput inters remote anr sensors likdity, wind smmunicateer, you can atile input inmunication nger a mera complete

WA wall moplosion proations in ha

sonic meteming the me in today’

eil, offer a p the demany major indight produce traditionaations, or wfits offered rs are requ

guratible Con

des variousrfaces. Whend you havke temperaspeed, etc.e to a remo do so usinnterfaces ainterface. S

re flow met remote sta

unt can be oof enclosurazardous ar

r are quickmeter techn’s marketplproduct pornds of virtuustry. We h

ct for applical meters hwhere the m by ultraso

uired.

on nfidenc

s input en the ve many ature, values te g the

and the So, it’s ter but ation.

housed re for reas.

ly ology of ace. We,

rtfolio to ually have cations ave

many nic

e

5

Versatility in Function You have the flowmeter but that’s not all! MU-WA has standard RS-485 interface. Using this interface, multiple meters at remote sites can be monitored or controlled almost at real time. Therefore the user can have the real time awareness of all of his meters out in the field at the comfort of his desk. Using the 2 Pt-100Ω RTD inputs as temperature inputs, the meter has the function as an energy meter. Using the output interfaces such as 4-20mA, pulse, relay, batch control, etc., process equipments such as pumps or valves can be controlled automatically.

Using the 3 analog inputs and RS-485 interface, the meter can function as an independent station where it can collect other information such as ambient temperature, humidity, pressure, wind speed, level, etc. and forward it to a central monitoring station through RS-485 communication. The meter circuit is composed of 1 main board and 1 display and keypad board and therefore has a roomy space inside in which the user can install accessories such as surge compressor, external data logger, pull-up resistors for pulse output, etc.

6

Handheld(MU-HA)

Portable(MU-PO

d

e O)

PortaThe id The handmost advultrasonicthe worldbigger thcapabilityranges fr The transmaximumhave magtransduceeasier. They canfrom oneThere is nor interru 16 site instored foquick set The meteruns aboumaximumfull in 6 h

able Cdeal sol

dheld type ivanced portc flowmeted. The size an a PDA b

y to measurom 15mm

sducers arem ease of ognets that er installati

also be eae job site tono need to upt the flow

nstallation pre easy ret

tup and ope

er uses Ni-Hut 10 hours

m load and hours.

Clamplution f

is one of thtable rs out thereis a little

but offers re all pipe to 6000mm

e designed operation anmake the ion much

asily movedo another. cut the pip

w.

parameterstrieval and eration.

H battery ths under is recharge

p-on Ffor plan

he

e in

m.

for nd

d

pe

s are

hat

ed

lowmnt surve

Utilizing thprocess hiand storedor laptop. The legacyequipped wprints out at real tim The portabmeters areverificationmeters, anlocations tbeing met Many watearound themeters as

eters eys

he built-in dstory can bd or downlo

y portable twith dot pr the measu

me.

ble ultrasone ideal checn of your mnd/or measthat are notered.

er service ce world are their audit

data loggerbe recordedoaded to a

type is inter that rement dat

nic flow-ck meter fo

mechanical surements it currently

companies e using thest meters.

r, d PC

ta

or

in

se

QA Thpotecpasizsatheweusca Thsindifloccaea Weof mebope Thbuor MUdato spmo Thkitarecoan

co

Quick a must-

he portable ortable, baschnology of

anel mount ze reductionme functioey reducedeights to inse and increpability.

he handheldngle-handefficult and ccated in nan now be psily.

e highly rec the MU-HAeasuring taoth portabilerformance.

he data canuilt-in data add-in datU-PO, MU-Wata so store a PC on a readsheet ouse button

he handheldt including e both houmpact alum

nd safe carr

GUI for remntrolling/ mon

and Ehave fo

types, hansed on the sf wall-mou feature sign. While attnality and a the sizes acrease the ease the da

d type (MU-d portabilitchallengingrrow or hig

performed s

commend pA for use in asks that deity and adv.

be stored logger (for ta logger mWA & MU-Ped can be dMicroSoft Ewith just a n.

d kit and thall their accsed in rugg

minum casery-around.

ote nitoring

GUI

asy or proce

ndheld and same nt and

gnificant taining the accuracy, and ease of ata logging

-HA)’s ty means jobs

gh places safely and

picking up flow emand vanced

on the MU-HA)

module (for A). The ownloadedExcel click of a

he portable cessories ged and es for easy

for Downloaddata to PC

ess val

Wheusenorpuroil sanda prcustdonsupcon Clamreco

p m

ing of

idation

en the trand up, the cmal greasechased at ashop. And td ink tape crint shop eatomer own

n’t need to pply of thossumable ite

mp-on flowommended

easy/low cono interrupt no need to no periodic cparts to weano contact wlarge pipe dm (240”) media underminimal maino pressure wide turn-do

UltrasoniGa

s nsducer seacustomer cae that can bany gas stathe printer can be purcasily. So, os the meterely on us fe expendabems.

wmeters are if you nee

ost installatiotion in operacut pipe cleaning andar or foul with media iameters up

r high pressuintenance drop or eneown ratio

c Thickness auge

SD Memo(81 x

alant is an use be ation or paper chased at once the r, they for ble or

e d:

on ation;

d moving

to 6000

ure

ergy loss

ory Card Modux 31 x 8mm)

H(

(

ule

Handheld (MU-HA)

Portable (MU-PO)

7

8

Energy (Heat) Meter Solution Full-function ultrasonic energy metering The wall mount type comes with energy (heat) meter function as built-in function. With the addition of 2 Pt-100Ω RTD sensors, you have a powerful energy (heat) meter and avoid the performance and reliability problems that afflict conventional intrusive thermal energy flowmeters. Almost all the engineering units for energy can be selected. And not only heat generation but also heat loss is calculated. Its high accuracy, wide bi-directional rangeability, and high sensitivity prevent the loss of energy cost billing now suffered when flow rates fall below the operating range of intrusive meters. Absolutely no pressure drop means lowest operating costs.

Installation is quick and easy; shut down is never needed for installation, maintenance, or calibration check, saving additional cost and inconvenience. Non-intrusive, clamp-on “no-wear” flow sensing delivers intrinsic high reliability. Ideal for a wide range of district energy heating and cooling applications and for power plants. And with the addition of Ethernet based remote monitoring and controlling system, the energy flow can be monitored at real time anywhere from a web-based applications. And the data collected at real time can be reported to a remote place by wireless using cellular technology.

Pt-100Ω RTD Temperature Transmitter

Cellular (CDMA) based RTU Ethernet-based Controller/Server

PT-100Ω, 3-wire film type RTD

SM TasizogdeBemamacoexis Thmiclathealltraflosigtheof theen In diatra In traand

UTra

A

SemicoMicro-flo

aking the adze full-boregy, the micresigned for ecause the ade of PFA akes an idenductor ind

xtreme clearequired.

he basic difficro-flow tramp-on trae sound sigy with clamavels squarow transducgnal travel e level of in the sound ereby maki

nce calculat

the clamp-on agonally with rvel distance is

the micro-flowvels squarely d the travel di

Upstreamansducer

UpstreamTransducer

Applicatio Chemical Pure wate Chemical Highly cor Chemical Ultra-low

onducow and

dvantage o transducero-flow senlow flow apwetted mat material, teal choice fodustry, whenness of pi

ference betansducer ansducer is gnal travelsmp-on transrely with thcer. Therefopath gets lncrease and velocity geing the timtion more a

transducers sregards to thes shorter.

w transducers with regards istance is long

ns mechanical per and ultras-p feeds rrosive chemi dosing applic flow and low

ctor In slurry

f the small r technol-sor is pplications.terials are this sensor or semi-ere the ipe inside

tween this and the that, while

s diagon-sducers, it e micro-ore the onger and d decrease ets bigger, e differ-ccurate.

signal travels e flow and the

s signal to the flow ger

Downtransd

Downstream transducer

olishing (CMPpure water in

cals ations flow velocity

ndustr sensin

e

Equintessinflowml/redsolirempowfunccomalar Thesemwafslurmeaconpumof t Maibelo

nstream ducer

P) slurries semiconducto

measurement

ry Solg techn

uipped witherface and dng technolow measuremm) as well uction of add influence

ment. Besidewerful capaction flowm

mmunicatiorm, etc.

e typical apmiconductorfer polishingrry. The measures flowstant flow

mp using 4-he meter.

n features ow;

Extremely All wetted Miniaturizefit into smaA wide seleChemical rCorrosion rVarious siz

or manufactur

ts

lutionnology

versatile udigital signa

ogy, it featuments (as lo as significadverse bub

e in the flowes, it retainbilities of fu

meter includn, signal ou

plication inr industry isg process ueter constaw and keepsby controlli-20mA outp

are summa

low flow: 5parts made

ed flow comall spaces ection of ouresistance resistance zes to choos

ring plants

user al proce-ures low ow as 5 ant bble or w measu-ns the ull-ding utputs,

the s in the using CMP ntly s the ing the put signal

arized

5 ml/m e of PFA

mputer to

utputs

se from

Micro

FloMicr

o-flow transdu

ow Computer ro-flow Transd

9

ucer

for ducer

Flow Computers Wall Mount Panel Mount Handheld Portable

Model Denominator MU-WA MU-PA MU-HA MU-PO

Full functionality using all types of sensors and the widest selection of output and input interfaces

Housed in panel to work as part of a whole system for monitoring and controlling a process

Light-weight and the most advanced portable version with internal data logging capability

Legacy portable type with dot printer capability

Pipes Measured Steel, stainless, cast iron, plastics, concrete or any pipes with known sound velocity property

Pipe Sizes 15 ~ 6000 mm

Fluid Water, sea water and other clean liquids without high level of suspended particles

Fluid Turbidity Smaller than 20,000ppm (mg/l) with a low level of air bubble content

Flow Velocity -30 ~ +30 m/s

Accuracy ±1.0% of Reading

Repeatability ±0.2% ~ 0.5%

Linearity 0.5%

Ambient Temp. -20 ~ +70℃

Ambient Humidity 85% RH Max.

IP Rating IP-66 IP-65 IP-65 IP-65

Power DC 24V

AC 110 ~ 250V

DC 24V Internal Battery

AC 110 ~ 250V charger

Internal Battery

AC 110 ~ 250V charger

Output 4-20 mA

Pulse

Batch Control Relay

RS-485

4-20 mA

Pulse

Batch Control Relay

RS-485

RS-232 RS-485

Optionally

4-20 mA, Pulse

Batch Control Relay

External Inputs 2 x RTD Inputs

3 x 4-20 mA Inputs

2 x RTD Inputs

3 x 4-20 mA Inputs

Optionally

2 x RTD Inputs

Data Logger Add-in SD Memory Card Module

Add-in SD Memory Card Module

Built-in Data Logger Add-in SD Memory Card Module

Max. Transducer Cable Length

400 m

Dimension 251 x 92 x 80 mm 90 x 90 x 34 mm 200 x 85 x 30 mm 258 x 180 x 10 0mm

Weight 5.5 kgs 5 kgs 9 kgs including transit case

9 kgs including transit case

Transducers Clamp-on Insertion Full-Bore

Pipe Ranges S 15~100 mm > 80 mm π Shape 10~40 mm

M 50~700 mm H Shape > 50 mm

L 300~6000 mm

Operating Temperature

-20 ~ +160℃ -20 ~ +130℃ -20 ~ +120℃

IP Rating IP 65** IP-65** IP 65**

Cable Length 5 m by standard (optionally, can be up to 400 m)

** Optionally IP68

Temperature Sensors Sensor Type PT-100 ohm RTD, 3-wire, film-type

Accuracy 0.1℃

Accuracy of Temperature Sensing Circuit 0.5%

11

Model Selection Guide MU-##-##-## Code

Flow Computer

Wall Mount WA

Panel Mount PA

Portable PO

Handheld HA

Transducer Clamp-On Small (for 15~100mm pipes) CS

Medium (for 50~700mm pipes) CM

Large (for 300~6000mm pipes) CL

Insertion 45-degree Tip ID

Flat Tip IF

Full Bore FDN

Ultra-Clean Micro-Flow Sensor

3 mm U3

6 mm U6

Power 100~250 VAC (Wall Mount, Portable, Handheld)

P1

24 VDC (Wall Mount, Panel Mount)

P2

Options Data Logger (SD Memory Card Module) SD

Ultrasonic Thickness Gauge UT

Explosion Proof Enclosure EX

High-Temperature Sensor HT

Special Cable Length (Standard 5m)

C___

RS-232 Converter RS232

Hot-Tapping Drill Tool DR

Example: MU-WA-CM-P2-EX: Explosion-proof wall mount ultrasonic flowmeter with M size clamp-on sensor powered by DC power.

Subje

ct t

o c

han

ge

withou

t prior

notice

12/0

8 |

Printe

d in K

ore

a |

© S

eil Ente

rprise

co.

2008

MAXIFLOTM is a registered trademark of Seil Enterprise Co.

Seil Enterprise Co. Seoul Korea www.maxiflo.co.kr

The information contained in this catalog contains merely general descriptions or characteristics of performance which in case of actual use do not always apply as described or which may change as a result of further development of the products. An obligation to provide the respective characteristics shall only exist if expressly agreed in terms of the contract. All product designations may be trademarks or product names of Seil Enterprise Co. whose use by third parties for their own purposes could violate the rights of the owners.

We are here for you For further information, visit us at www.maxiflo.co.kr