LT-6152 rev 3.2 © Mircom 2018. Printed in Canada Subject to change without prior notice See http://www.mircom.com/tx3 for the latest information For more information, see LT-6637 and LT-1194 on the included USB disk and http://www.mircom.com/tx3 Mircom Tech Support: 1-888-MIRCOM5 (888-647-2665) [email protected] TX3 NANO QUICK START WARNING: Do not mount the TX3 Nano in direct sunlight. Disconnect the power before wiring. TX3 Nano dimensions: 219 mm x 147 mm x 47 mm (8 19/32” x 5 3/4” x 1 27/32”) Mounting plate dimensions: 200 mm x 140 mm (7 27/32" x 5 1/2") 1. Press and hold the Home button for 10 seconds. The TX3 Nano’s IP address and MAC address appear on the display. 2. On a computer on the same local area network as the TX3 Nano, open Google Chrome or Internet Explorer 11 or higher and type the IP address of the TX3 Nano, and then press enter. Username: admin Password: admin Conﬁgure 6 Insert security screw 5 Apply silicone to this groove. Do not apply silicone to any other part of the TX3 Nano. Apply outdoor-rated weatherproof silicone to groove in mounting plate 1 Bottom Back Holes for gang box Use 2 screws to hold gang box in place 3 Attach TX3 Nano to mounting plate 4 Attach the mounting plate to wall with at least 6 fasteners Attach mounting plate to wall 2 Front MOUNTING 12-48 VDC / 15 W Auxiliary power input (20-18 AWG) Phone line + - R T OUTPUT: lock (18 AWG) INPUT 2: general purpose (22 AWG) INPUT 1: door contact (22 AWG) NO NC COM + - + - For future use USB 2.0 port: for debugging only (maximum length of USB cable: 2.4 m (8 feet) RJ45 connector for LAN connection and Power over Ethernet PoE maximum length: 100 m (328 ft) USB switch: for debugging only (leave to the right) Slot for mini SIM (2FF) card (only models with-C, for example TX3-NANO-S4-CX) Screw for adjusting camera tilt Contact rating: 30 VDC/2 A or 125 VAC/0.5 A Note: The TX3 Nano has a tamper feature. If it is powered on and not mounted on the mounting plate, a tone sounds. The tone stops sounding when it is mounted.

TX3 NANO QUICK START - Mircom · For future use USB 2.0 port: for debugging only (maximum length of USB cable: 2.4 m (8 feet) RJ45 connector for LAN connection and Power over Ethernet

Download PDF Report

Upload
others
View
3
Download
0

Embed Size (px)

Citation preview

Page 1: TX3 NANO QUICK START - Mircom · For future use USB 2.0 port: for debugging only (maximum length of USB cable: 2.4 m (8 feet) RJ45 connector for LAN connection and Power over Ethernet

LT-6152 rev 3.2 © Mircom 2018. Printed in CanadaSubject to change without prior notice

See http://www.mircom.com/tx3 for the latest information

For more information, see LT-6637 and LT-1194 on the included USB disk and http://www.mircom.com/tx3Mircom Tech Support: 1-888-MIRCOM5 (888-647-2665) [email protected]

TX3 NANO QUICK STARTWARNING: Do not mount the TX3 Nano in direct sunlight.Disconnect the power before wiring.

TX3 Nano dimensions:219 mm x 147 mm x 47 mm (8 19/32” x 5 3/4” x 1 27/32”)Mounting plate dimensions: 200 mm x 140 mm (7 27/32" x 5 1/2")

1. Press and hold the Home button for 10 seconds. The TX3 Nano’s IP address and MAC address appear on the display.2. On a computer on the same local area network as the TX3 Nano, open Google Chrome or Internet Explorer 11 or higher and type the IP address of the TX3 Nano, and then press enter.

Username: admin Password: admin

Con�gure6Insert security screw5

Apply silicone to this groove.Do not apply silicone to any other part of the TX3 Nano.

Apply outdoor-rated weatherproof silicone to groove in mounting plate

BottomBack

Holes for gang box

Use 2 screws to hold gang box in place3

Attach TX3 Nano to mounting plate4

Attach the mounting plate to wall with at least 6 fasteners

Attach mounting plate to wall2

Front

MOUNTING

12-48 VDC / 15 W Auxiliary power input (20-18 AWG)

Phone line+-

OUTPUT: lock(18 AWG)

INPUT 2: general purpose (22 AWG)INPUT 1: door contact (22 AWG)

NONCCOM

For future use

USB 2.0 port: for debugging only

(maximum length of USB cable: 2.4 m (8 feet)

RJ45 connector for LAN connection and Power over Ethernet

PoE maximum length: 100 m (328 ft)

USB switch:for debugging only (leave to the right)

Slot for mini SIM (2FF) card (only models

with-C, for example TX3-NANO-S4-CX)

Screw for adjusting camera tilt

Contact rating: 30 VDC/2 A or125 VAC/0.5 A

Note: The TX3 Nano has a tamper feature. If it is powered on and not mounted on the mounting plate, a tone sounds. The tone stops sounding when it is mounted.