Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
Trade Price ListApril 2018
J41745 Philmac Price List_Final_A4_cover pages.indd 2 13/03/2018 17:23
3PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
Introduction 2
3G METRIC/IMPERIALTM
Introduction 4 - 5
Fittings Range 6 - 9
Liners and Connection kits 10 - 12
Pipe Standards 14 - 15
UTC
UNIVERSAL TRANSITION COUPLINGS
Introduction 17 - 18
Principles of Operation 19
Fittings Range 20
UTC Guide 21
LARGE BORE METRIC
Introduction 22
Fittings Range 23
VALVES
Introduction 24 - 25
Valve Range 26 - 27
M.I. Connectors suitable for our valves 27
BSP THREADED FITTINGS
Introduction 28 - 29
Fittings range 30 - 32
SUNDRIES 33
PROPERTIES - Chemical Resistance Chart 35
CONTACT DETAILS 36 - 37
T&Cs 43
CONTENTSPhilmac is a global leader in the design and manufacture of specialist pipe fittings and valves, providing cost-effective solutions for the transfer, control and application of water. With a commitment of providing the very best in customer service and technical know how, Philmac is the conection you can trust.
THE ENVIRONMENT We actively and consistently strive to reduce our impact on the environment and operate an environmental management system accredited to ISO 14001:2015.
QUALITY Philmac operates an accredited Quality Management System to BS EN ISO 9001:2015 to ensure peace of mind for our customers.
For further information visit www.philmac.co.uk
4 5PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
Liners must be used with metric pipe sizes 20, 25, 32, 50 & 63mm.
No pipe preparation is needed and no force is required to push the pipe past the seal, so installation could not be faster or easier. Simply insert the pipe fully into the fitting and then tighten the nut. Assembly is so easy that you can even do it under live conditions.
No special tools are required and there is no need to disassemble the fitting before use because the Metric/ImperialTM compression fitting is supplied pre-assembled and ready to use.
THE COMPLETE SOLUTION
METRIC/IMPERIAL™ TECHNICAL MANUAL 11
FULLY OPEN
FULLY CLOSED
Fitting is pre-assembled ready to use in the open position with 2 threads showing.
PRINCIPALS OF OPERATION
Clearance between the pipe and fitting allows for easy insertion of the pipe.
Seal, which is in relaxed position.
Split collet, which is in relaxed position.
The pipe sits against the tapered wedges which minimises pipe rotation.
Positive internal stop when nut meets flange of the body.
Split collet bites into the pipe providing end load resistance.
Nut and then split collet has fully compressed the seal. Seal ring compression is achieved by exploiting the mechanical advantage of the nut thread.
MATERIALS & COMPONENTS
NUT – Acetal
BODY – Polypropylene
SPLIT COLLET – Acetal
SEAL – Nitrile Rubber
3G Met Imp master V2.indd 11 18/12/2008 10:13:15 PM
Fast and Easy InstallationSlide & TightenTM technology: 3G® compression fittings incorporate all the benefits of Philmac’s unique Slide & TightenTM technology. No pipe preparation is needed, no force is required to push the pipe past the seal. This means faster and easier installation because the fitting seals on the outside of the pipe. Simply insert the pipe into the fitting until the first point of resistance is felt, and then tighten the nut.
Compact design: The size of the Philmac 3G® compression fitting has been kept to a minimum, making the fitting ideal for use in confined areas.
Easy disassembly: The fitting has been designed so the grip ring is released as soon as the nut is backed off, making disassembly easy.
Complete SecurityVisual stop: With Metric Pipe, the body flange on the 3G® compression fitting acts as a visual stop to indicate when the nut is tightened. There is no benefit in further tightening of the nut.
No loose conponents: If the nut is removed there is no danger of losing components, as the grip ring and seal ring are retained in the body of the fitting.
Dynamic sealing method: As the nut is tightened, the seal is compressed between the pipe and the fitting body.
Designed to minimize pipe twist: The fitting has been designed to minimize pipe twist as the nut is tightened. Maximum pipe twist is approximately a quarter turn compared with one and a half turns with many other fittings.
Approvals: Philmac 3G® compression fittings are WRAS approved for potable water use.
Lead FreeThe Philmac range of 3G® compression fittings is completely free of lead.
High Performance MaterialsManufactured from Engineered Materials: 3G® compression fittings are manufactured from lightweight high performance thermoplastic materials that, unlike metal fittings, resist corrosion, significantly minimizing maintenance, repairs and long-term costs. The materials are non-toxic and taint-free.
Complete CoverageWide range: The 3G® compression fittings range is comprehensive: straight and reducing couplers, tees, elbows, male and female adapters and caps ranging from ½" to 2".
Patent protected the Metric/ImperialTM plastic compression fitting is the product of the company’s unrelenting commitment to continuous improvement and a culture based on innovation and ingenuity.
Seven into ONE will goConnects
Blue MDPE BS 6572Black MDPE BS 6730
Low Density Class C BS 1972Low Density Class D BS 1972High Density Class C BS 3284High Density Class D BS 3284
IRS 135 Heavy Gauge BS 1972/61
No need for inserts or dedicated fittings
Materials & Components
Long-lasting, corrosion resistant and easy to install, Philmac fittings have proven
themselves in irrigation and commercial applications all over the world. They are the
fitting choice for both contractors and installers.
3G METRIC/IMPERIAL | INTRODUCTION
6 7PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
Pipe Repair KitRepairs Metric/Imperial Damaged Pipe
20mm 1/2"
Contents:1 x Length of pipe
1 x 3G Metric/Imperial Slip Coupling
1 x 3G Metric /Imperial Joiner
4 x Liners
Tel: +44 (0) 1323 847323www.philmac.co.uk Diplocks Way, Hailsham, East Sussex BN27 3JF
Other pack sizes available
Part no. PRK20
Seven into one will go
High Density Class C BS 3284 High Density Class D BS 3284 IRS 136 Heavy Gauge BS 1972/61
Blue MDPE BS 6572 Black MDPE BS 6730 Low Density Class C BS 1972 Low Density Class D BS 1972
philmac header 105 x 60 20mm_ALL AS ONE_FINAL.indd 1 18/04/2017 13:43
Description Part No. Sizes Pks Price
METRIC/IMPERIALJOINER POL X POL
912291339144915591669177
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
10105111
4.805.06
12.0026.4327.6141.55
SLIP JOINER METRIC/ IMPERIAL POL X POLNo internal pipe stop, ideal flexibility for repair or retrofit
901229013390144901559016690177
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
111111
6.927.75
15.9729.1236.9255.58
METRIC/IMPERIALREDUCING JOINERPOL X POL
91329142914391539154916391649165917491759176
25mm/¾" x 20mm/½"32mm/1" x 20mm/½"32mm/1" x 25mm/¾"40mm/1¼" x 25mm/¾"40mm/1¼" x 32mm/1"50mm/1½" x 25mm/¾"50mm/1½" x 32mm/1"50mm/1½" x 40mm/1¼"63mm/2" x 32mm/1"63mm/2" x 40mm/1¼"63mm/2" x 50mm/1½"
105511111111
9.8915.9715.9730.1130.1144.2844.2846.0259.5161.7861.78
METRIC/IMPERIALEND CONNECTORPOL X M.I. BSP
922192229223923192329233924292439244924592539254925592569265926692759276
20mm/½" x ½" BSP20mm/½" x ¾" BSP20mm/½" x 1" BSP25mm/¾" x ½" BSP25mm/¾" x ¾" BSP25mm/¾" x 1" BSP32mm/1" x ¾" BSP32mm/1" x 1" BSP32mm/1" x 1¼" BSP32mm/1" x 1½" BSP40mm/1¼" x 1" BSP40mm/1¼" x 1¼" BSP40mm/1¼" x 1½" BSP40mm/1¼" x 2" BSP50mm/1½" x 1½" BSP50mm/1½" x 2" BSP63mm/2" x 1½" BSP63mm/2" x 2" BSP
101010101010555511111111
4.355.278.355.685.538.838.048.04
16.8116.8118.9218.9221.0524.0420.5523.6428.9428.94
Description Part No. Sizes Pks Price
METRIC/IMPERIALEND CONNECTOR POL X F.I. BSP
98219822982398319832983398429843984498549855986598669876
20mm/½" x ½" BSP20mm/½" x ¾" BSP20mm/½" x 1" BSP25mm/¾" x ½" BSP25mm/¾" x ¾" BSP25mm/¾" x 1" BSP32mm/1" x ¾" BSP32mm/1" x 1" BSP32mm/1" x 1¼" BSP40mm/1¼" x 1¼" BSP40mm/1¼" x 1½" BSP50mm/1½" x 1½" BSP50mm/1½" x 2" BSP63mm/2" x 2" BSP
10101010101055511111
5.886.178.166.506.357.567.567.60
22.3722.2523.4624.1133.80 33.80
METRIC/IMPERIALTEE - EqualPOL X POL
932293339344935593669377
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
1055111
8.6313.5116.9140.3239.4661.13
SLIP TEEMETRIC/IMPERIALNo internal pipe stop, ideal flexibility for repair or retrofit
9032290333903449036690377
20mm/½"25mm/¾"32mm/1"50mm/1½"63mm/2"
11111
12.4118.6323.0351.24 78.59
METRIC/IMPERIALTEE - ReducingPOL X POL
933293349343936393649365937393749376
25mm/¾" x 25mm/¾" x 20mm/½"25mm/¾" x 25mm/¾" x 32mm/1"32mm/1" x 32mm/1" x 25mm/¾"50mm/1½" x 50mm/1½" x 25mm/¾"50mm/1½" x 50mm/1½" x 32mm/1"50mm/1½" x 50mm/1½" x 40mm/1¼"63mm/2" x 63mm/2" x 25mm/¾"63mm/2" x 63mm/2" x 32mm/1"63mm/2" x 63mm/2" x 50mm/1½"
555111111
13.8820.2920.2949.5949.5941.8762.5862.5861.13
METRIC/IMPERIAL TEE POL X M.I. BSP
99319932
25mm/¾" x ½" BSP25mm/¾" x ¾" BSP
55
10.8213.08
PIPE REPAIR KITS
PRK20PRK25PRK32
PIPE REPAIR KIT 20MMPIPE REPAIR KIT 25MM PIPE REPAIR KIT 32MM
111
25.3426.9844.55Liners to suit MDPE pipe are required for WRAS
requirements, please see page 11 for these items
NEW
3G METRIC/IMPERIAL | COMPRESSION FITTINGS
See our installation videos on YouTube at Philmac UK See our installation videos on YouTube at Philmac UK
8 9PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
3G METRIC/IMPERIAL | COMPRESSION FITTINGS
Liners to suit MDPE pipe are required for WRAS requirements, please see page 11 for these items
Description Part No. Sizes Pks Price
METRIC/IMPERIALTEE POL X F.I. BSP
9421942294319432943394419442944394449454945594619462946594669476
20mm/½" x ½" BSP20mm/½" x ¾" BSP25mm/¾" x ½" BSP25mm/¾" x ¾" BSP25mm/¾" x 1" BSP32mm/1" x ½" BSP32mm/1" x ¾" BSP32mm/1" x 1" BSP32mm/1" x 1¼" BSP40mm/1¼" x 1¼" BSP40mm/1¼" x 1½" BSP50mm/1½" x ½" BSP50mm/1½" x ¾" BSP50mm/1½" x 1½" BSP50mm/1½" x 2" BSP63mm/2" x 2" BSP
101055555551111111
8.3712.6713.3313.3316.1216.2116.2116.2132.6632.5036.5037.3837.3837.3848.5352.46
METRIC/IMPERIALELBOW POL X POL
952295339544955595669577
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
10105111
6.429.48
13.8229.5832.0843.61
METRIC/IMPERIAL REDUCING ELBOWPOL X POL
9532 25mm/¾" x 20mm/½" 10 9.48
METRIC/IMPERIALELBOW POL X F.I. BSP
962196229631963296339643964496549655966596669676
20mm/½" x ½" BSP20mm/½" x ¾" BSP25mm/¾" x ½" BSP25mm/¾" x ¾" BSP25mm/¾" x 1" BSP32mm/1" x 1" BSP32mm/1" x 1¼" BSP40mm/1¼" x 1¼" BSP40mm/1¼" x 1½" BSP50mm/1½" x 1½" BSP50mm/1½" x 2" BSP63mm/2" x 2" BSP
10101010105511111
5.827.368.157.93
11.8311.8926.2326.0928.4428.2336.8937.02
METRIC/IMPERIAL ELBOW POL X M.I. BSP
972197329743 974497539754975597659776
20mm/½" x ½" BSP25mm/¾" x ¾" BSP32mm/1" x 1" BSP32mm/1" x 1¼" BSP*40mm/1¼" x 1" BSP*40mm/1¼" x 1¼" BSP*40mm/1¼" x 1½" BSP*50mm/1½" x 1½" BSP*63mm/2" x 3" BSP*
10105511111
5.828.15
13.8017.7321.8221.7422.7431.5646.10
METRIC/IMPERIAL 45 DEG ELBOW POL X POL
9028903890489058 9068 9078
20mm/½"* 25mm/¾"*32mm/1"*40mm/1¼*50mm 1½"*63mm 2"*
111111
6.429.48
13.8129.5832.0843.62
Description Part No. Sizes Pks Price
METRIC/IMPERIALTANK CONNECTORASSEMBLYc/w Seal Washers
97809781
25mm/¾" x ¾" BSP32mm/1" x 1" BSPOther tank connector optionsavailable on page 40
105
12.2414.76
METRIC/IMPERIALEND CAP
902990399049905990699079
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
10105111
5.237.029.36
18.4922.6232.03
METRIC/IMPERIALWALL PLATE ELBOW PLASTIC
902290319032
20mm/½" x ½" BSP25mm/¾" x ½" BSP25mm/¾" x ¾" BSP
555
11.9013.9215.23
METRIC/IMPERIALWALL PLATEELBOW METAL
92289229
20mm/½" x ½" BSP25mm/¾" x ¾" BSP
55
26.3132.62
HOSE UNION BIB TAP BS2682 CV
30223033
DZR ½" c/w double check valveDZR ¾" c/w double check valve
11
20.5630.96
ARCTIC ICE RESISTANT BIB TAP
802180228023
½" BSP¾" BSP1" BSP *Water: -20°CFor Arctic Resistance Ball Valves, see page 26
111
16.8123.5745.29
HOSE UNION TAPCONNECTOR
HOSCON 21 HOSCON 22
½"¾" (to suit 8022 only)
11
1.772.03
METRIC SADDLE 9063590735
50mm x 25mm/¾"63mm x 25mm/¾"
11
27.5828.40
FLANGE ADAPTORFlange to BS 4504
8776687776
50mm/1½" x 2"63mm/2" x 2"
11
114.11114.11
NEWNEW
* New sizes now available
10 11PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
3G METRIC/IMPERIAL | LINERS & CONNECTION KITS
Description Part No. Sizes Pks Price
PE x Copper/PEX Push Fit (above ground)TWO PART ASSEMBLED TO CORRECT TORQUE. DO NOT TIGHTEN FURTHER
JOINER 13211331133213421343
20mm/½" x 15mm25mm/¾" x 15mm25mm/¾" x 22mm32mm/1" x 22mm32mm/1" x 28mm
11111
10.6212.9612.9617.8519.46
ELBOW 1521153115322543
20mm/½" x 15mm25mm/¾" x 15mm25mm/¾" x 22mm32mm/ 1" x 28mm
1111
10.6212.9612.9622.01
FOR CONNECTIONS TO PEX PIPE PLEASE REFER TO PIPE MANUFACTURERS INSTALLATION INSTRUCTIONS AND ONLY USE PEX LINERS COMPATIBLE WITH THE PIPE BEING USED
Description Part No. Sizes Pks Price
MDPE LINERSEN12201/ BS 6572 (below ground)
EN12201/ BS 6730(above ground)
7800278003780047800678007
20mm25mm32mm50mm63mm
100100502520
0.370.400.661.301.59
METRIC/IMPERIALCONNECTION KIT
999002999003999004999005999006999007
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
202010555
1.261.392.022.594.536.05
METRIC/IMPERIALREDUCING SETSBS 6572/6730 MetricBS 1972/3284 & IRS 135Imperial
9803298042980439806398064980739807498076
25mm/¾" x 20mm/½"32mm/1" x 20mm/½"32mm/1" x 25mm/¾"50mm/1½" x 25mm/¾"50mm/1½" x 32mm/1"63mm/2" x 25mm/¾"63mm/2" x 32mm/1"63mm/2" x 50mm/1½"
10101055555
3.354.784.789.939.93
14.9614.9614.96
METRIC/IMPERIALNORMAL GAUGECONNECTION KITBS 1972 IRS 134
930029300393004930059300693007
½" (fits 3/8 " LD and HD)¾"1"1¼"1½"2"
101010555
1.151.381.653.574.416.71
METRIC/IMPERIALNORMAL GAUGEREDUCING SETS
931329314293143
¾" x ½"1" x ½"1 x ¾"
101010
4.406.095.23
Liners to suit MDPE pipe are required for WRAS requirements, please see page 11 for these items
Ball Valve
Body Size
METRIC/IMPERIAL¼ Turn BALL VALVE POL X POL
95272953729527395373
20mm/½"(16mm Nominal Bore)25mm/¾"(16mm Nominal Bore)25mm/¾"(19.5mm Nominal Bore)32mm/1" (19.5mm Nominal Bore)
1111
36.8338.4646.4750.58
Stopcock
METRIC/IMPERIALSTOPCOCK POL X POL
282228332844
20mm/½"25mm/¾"32mm/1"
552
27.7040.9562.52
METRIC/IMPERIALSTOPCOCK POL x FI
28312832 28422843
25mm/¾" x ½" 25mm/¾" x ¾" 32mm/1" x ¾" 32mm/1" x 1"
5522
39.6039.6060.4560.45
See our installation videos on YouTube at Philmac UK See our installation videos on YouTube at Philmac UK
12 13PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
3G METRIC/IMPERIAL | NOTES3G METRIC/IMPERIAL | LINERS & CONNECTION KITS
Description Part No. Sizes Pks Price
METRIC/IMPERIAL COPPER CONNECTION KIT BS EN 1057Connection Kit for copper pipe for above and below ground use
86002860038600486032
20mm/½" x 15mm25mm/¾" x 22mm32mm/1" x 28mm25mm/¾" x 15mm
Suitable for single use onlyNot suitable for PB or PEX pipe
10101010
5.225.507.805.39
METRIC/IMPERIALBLANKING PLUG
912891389148915891689178
20mm/½"25mm/¾"32mm/1"40mm/1¼"50mm/1½"63mm/2"
10105555
1.722.362.524.134.677.82
METRIC PVC/ABSCONNECTION KIT
942029420394204942059420694207
20mm25mm32mm40mm50mm63mm
101010111
3.783.904.027.099.11
11.35
IMPERIAL PVC/ABS CONNECTION KIT
94402944039440494405
944061944071
½" (20mm/½" body)¾" (25mm/¾" body)1" (32mm/1" body)1¼" (40mm/1¼" body)1½" (50mm/1½" body)*2" (63mm/2" body)*
*Complete with nut and seal
101010111
3.783.904.027.09
17.9022.43
See our installation videos on YouTube at Philmac UK
14 15PHILMAC PRICE GUIDE PHILMAC PRICE GUIDE
3G METRIC/IMPERIAL | PIPE STANDARDS
Outside Diameter Wall ThicknessNOMINAL SIZE MIN MAX MIN MAX
INCH MM MM MM MM
MDPE TO WATER INDUSTRY STANDARD EN 12201, BS 6572 & BS 6730
½ 20 20.3 2.3 2.6
¾ 25 25.3 2.3 2.6
1 32 32.3 3.0 3.4
1½ 50 50.3 4.6 5.2
2 63 63.3 5.8 6.5
CLASS C LOW DENSITY (TYPE 32) POLYETHYLENE PIPES TO BS1972/67
17 17.3 2.2 2.5
½ 21.2 21.5 2.7 3
¾ 26.6 26.9 3.4 3.7
1 33.4 33.7 4.2 4.6
1¼ 42.1 42.5 5.3 5.8
1½ 48.1 48.5 6.1 6.7
2 60.1 60.6 7.6 8.4
3 88.6 89.3 11.2 12.3
CLASS D LOW DENSITY (TYPE 32) POLYETHYLENE PIPES TO BS1972/67
17 17.3 2.8 3.1
½ 21.2 21.5 3.4 3.7
¾ 26.6 26.9 4.3 4.7
1 33.4 33.7 5.4 5.9
1¼ 42.1 42.5 6.8 7.5
1½ 48.1 48.5 7.8 8.6
CLASS C HIGH DENSITY (TYPE 50) POLYETHYLENE PIPES TO BS3284/67
½ 21.2 21.5 1.8 2.0
¾ 26.6 26.9 2.3 2.6
1 33.4 33.7 2.8 3.1
1¼ 42.1 42.5 3.6 4.0
1½ 48.1 48.5 4.1 4.5
2 60.1 60.6 5.1 5.6
3 88.6 89.3 7.5 8.2
4 113.9 114.7 9.6 10.6
Outside Diameter Wall ThicknessNOMINAL SIZE MIN MAX MIN MAX
INCH MM MM MM MM
CLASS D HIGH DENSITY (TYPE 50) POLYETHYLENE PIPES TO BS3284/67
17 17.3 1.9 2.1
½ 21.2 21.5 2.3 2.6
¾ 26.6 26.9 2.9 3.2
1 33.4 33.7 3.7 4.1
1¼ 42.1 42.5 4.6 5.1
1½ 48.1 48.5 5.3 5.8
2 60.1 60.6 6.6 7.3
3 88.6 89.3 9.7 10.7
NORMAL GAUGE BS1972/61 IRS 134 USE RED INSERT, SEE PG ** (TBA)
½ 16.95 17.30 2.30 2.60
¾ 24.95 25.40 3.10 3.50
1 31.25 31.75 3.10 3.50
1¼ 37.50 38.10 3.10 3.50
1½ 43.80 44.45 3.50 3.90
2 60.00 60.85 4.65 5.20
HEAVY GAUGE BS1972/61 IRS 135
½ 20.70 21.10 4.30 4.85
¾ 27.05 27.45 4.30 4.85
1 33.85 34.10 4.30 4.85
1¼ 42.00 42.65 5.05 5.60
1½ 47.95 48.65 5.35 5.90
17PHILMAC PRICE GUIDE
THE PROBLEM SOLVERPatent protected the Metric/ImperialTM plastic compression fitting is the product of the company’s unrelenting commitment to continuous improvement and a culture based on innovation and ingenuity.
Fast and Easy Installation
Slide & TightenTM The Philmac UTC® incorporates all the benefits of Philmac’s Slide & Tighten™ technology. Simply witness mark the pipe against the flange on the fitting, and then insert the pipe to the correct depth. The nut can then be tightened using a wrench. The UTC® is fully installed when the nut can no longer be tightened with reasonable force. No special tools are required and the Philmac UTC® is supplied ready to use.*Pipes at the top end of the fitting tolerance may incur minimum resistance.
Easy disassembly: The design of the UTC® means that once the nut is backed off, the pipe can easily be removed from the fitting.
Complete Security
Visual stop: The mechanical advantage of the nut thread compresses the seal into position, eliminating resistance when inserting the pipe into the fitting, so there is no risk of seal distortion or displacement.
No loose conponents: The Philmac UTC® is pre-assembled and ready to use, there are no loose components. There is no need for individual assembly of a grip ring, sealing ring or nut. All that is required is the insertion of the pipe and tightening of the nut.
Dielectric (insulating) fitting: UTC® fittings are insulating and are a dielectric fitting for use between dis-similar metals.
End load resistant: UTC® fittings are fully end load resistant and do not require the use of thrust blocks.
Approvals: Philmac UTC® fittings are WRAS approved for potable water use.
UTC | INTRODUCTION
The UTC is a unique range of mechanical compression fittings that provide the ultimatein pipe connection flexibility.
Our Slide & Tighten™ technology means no pipe preparation is needed,
no force is required to push the pipe past the seal. This means faster
installation because the fitting seals on the outside of the pipe.
For more information visit www.philmac.co.uk or contact us on 0844 335 0016
Fast and Easy Installation – Slide & Tighten technology
Complete Security – pre assembled and no risk of damage to pipes when fitting
High Performance Materials – manufactured from advanced thermoplastic engineered materials
Complete Coverage – connecting a wide variety of pipes together including Copper, Stainless Steel, ABS, Galvanised Iron and Lead.
Connects PE to a wide variety of pipes
PVC, copper, galvanised iron, ABS, lead, stainless steel, polyethylene
and PEX
Connects a wide variety of pipes together
PVC, copper, galvanised iron, ABS, lead, stainless steel, polyethylene
and PEX
Copper
Black Imperial
Steel
Pex
Galvanised
ABS
Lead
The Problem SolverUTC – Universal Transition Coupling
19PHILMAC PRICE GUIDE18 PHILMAC PRICE GUIDE
High Performance Materials
Manufactured from Advanced Thermoplastic Engineered Materials: The Philmac UTC® is manufactured from lightweight high performance thermoplastic materials with outstanding impact, UV, chemical and corrosion resistance. The UTC® end contains hard stainless steel grippers which provide superior end load resistance.
The Philmac UTC® is pressure rated to 12.5 Bar at 20°C to meet the needs of high pressure systems.
Complete Coverage
Wide range: The Philmac UTC® range is comprehensive: Straight and reducing couplers, elbows and male adaptors, in both transition (PE to UTC®) and double ended versions (UTC® to UTC®) ranging from 15 mm to 61 mm)
* Cold Water Only
NB:- For the PE 3G end, a liner is required for PE pipe
FULLY CLOSED – 3G™ PE END FULLY CLOSED – UTC® END
The nut is tightened with a wrench firmly to ensure proper installation. Some threads may be exposed, depending on the size of pipe inserted into the fitting.
Seal ring compression is achieved by exploiting the mechanical advantage of the thread.
Split ring with the stainless grippers bites into the pipe providing end load resistance
Positive internal stop when nut meets flange of the body.
Split collet bites into the pipe providing end load resistance.
Nut and then split collet has fully compressed the seal. Seal ring compression is achieved by exploiting the mechanical advantage of the nut thread.
FULLY OPEN – 3G™ PE END FULLY OPEN – UTC® END
Fitting is pre-assembled in the ready to use position with 3 threads showing
Clearance between the pipe and fitting allows for easy insertion of the pipe
Seal – is in a relaxed position
Split ring – is in a relaxed position
Pipe is inserted up to the flange on the fitting
Fitting is pre-assembled ready to use in the open position with 2 threads showing
Clearance between the pipe and fitting allows for easy insertion of the pipe
Seal, which is in relaxed position
Split collet, which is in relaxed position
The pipe sits against the tapered wedges which minimises pipe rotation
UNIVERSAL TRANSITION COUPLING TECHNICAL MANUAL 3
FAMILY OF FITTINGS - A COMPREHENSIVE RANGE
Repair work UTC® is used extensively by water companies, plumbers and civil contractors for repair work. The UTC® x UTC®
fitting was originally developed as a copper to copper repair joint at the request of a global water company.
New installations Connecting polyethylene pipe to water meter risers and polyethylene pipe to copper.
UTC® fittings are used by water companies as a connection between polyethylene pipe and metal pipes.
Upgrades UTC® is particularly useful in service line upgrades. A small number of PE x UTC® fitting provide a complete
solution and will connect to whatever pipe the installer finds at the property boundary.
A UTC® x Threaded Tee provides a solution when tieing an irrigation system into an existing water service line.
APPLICATIONS
PVC
Copper
Stainless Steel
ABS
Galvanised Iron
Lead
PVC
Copper
Stainless Steel
ABS
Galvanised Iron
Lead
PVC
Copper
Stainless Steel
ABS
Galvanised Iron
Lead
PE IMPERIAL
PE METRIC
PE x UTC UTC x UTC
MaleAdaptor
xUTC
Tee
UTC
FI Tee
UTC
Coupler
UTCx
UTC
ReducingCoupler
UTCx
UTC
Connects PE to a wide variety of pipes
Connects a wide variety of pipes together
Coupler3G Metric/
ImperialPEx
UTC
COMPLETE RANGE
Elbow
UTC
PVC, copper, galvanised iron, ABS, lead, stainless steel, steel, polyethylene and PEX
PVC, copper, galvanised iron, ABS, lead, stainless steel, steel, polyethylene and PEX
Tee3G Metric/
ImperialPEx
UTC
UTC_tech manual_METRIC-IMPERIAL.indd 3 18/12/2008 6:23:48 AM
UNIVERSAL TRANSITION COUPLING TECHNICAL MANUAL 3
FAMILY OF FITTINGS - A COMPREHENSIVE RANGE
Repair work UTC® is used extensively by water companies, plumbers and civil contractors for repair work. The UTC® x UTC®
fitting was originally developed as a copper to copper repair joint at the request of a global water company.
New installations Connecting polyethylene pipe to water meter risers and polyethylene pipe to copper.
UTC® fittings are used by water companies as a connection between polyethylene pipe and metal pipes.
Upgrades UTC® is particularly useful in service line upgrades. A small number of PE x UTC® fitting provide a complete
solution and will connect to whatever pipe the installer finds at the property boundary.
A UTC® x Threaded Tee provides a solution when tieing an irrigation system into an existing water service line.
APPLICATIONS
PVC
Copper
Stainless Steel
ABS
Galvanised Iron
Lead
PVC
Copper
Stainless Steel
ABS
Galvanised Iron
Lead
PVC
Copper
Stainless Steel
ABS
Galvanised Iron
Lead
PE IMPERIAL
PE METRIC
PE x UTC UTC x UTC
MaleAdaptor
xUTC
Tee
UTC
FI Tee
UTC
Coupler
UTCx
UTC
ReducingCoupler
UTCx
UTC
Connects PE to a wide variety of pipes
Connects a wide variety of pipes together
Coupler3G Metric/
ImperialPEx
UTC
COMPLETE RANGE
Elbow
UTC
PVC, copper, galvanised iron, ABS, lead, stainless steel, steel, polyethylene and PEX
PVC, copper, galvanised iron, ABS, lead, stainless steel, steel, polyethylene and PEX
Tee3G Metric/
ImperialPEx
UTC
UTC_tech manual_METRIC-IMPERIAL.indd 3 18/12/2008 6:23:48 AM
CONNECTS PE TO A WIDE VARIETY OF PIPESPVC, copper, galvanised
iron, ABS, lead, stainless steel, steel, polyethylene and PEX
CONNECTS A WIDE VARIETY OF PIPES TOGETHER
PVC, copper, galvanised iron, ABS, lead, stainless steel, steel, polyethylene
and PEX*
PRINCIPLES OF OPERATION | COMPRESSION FITTINGSUTC | INTRODUCTION
19PHILMAC PRICE GUIDE
21PHILMAC PRICE GUIDE20 PHILMAC PRICE GUIDE
UTC | GUIDEUTC | FITTINGS RANGE
Description Part No. Sizes Pks Price
UNIVERSAL TRANSITIONJOINER UTC X POLc/w Metric MDPE Liner
103210331042104310521053105410551074107510641065108610871097
15-21mm x 20mm/½"15-21mm x 25mm/¾"21-27mm x 20mm/½"21-27mm x 25mm/¾"27-34mm x 20mm/½"27-34mm x 25mm/¾"27-34mm x 32mm/1"27-34mm x 40mm/1¼"34-39mm x 32mm/1"34-39mm x 40mm/1¼"39-43mm x 32mm/1"39-43mm x 40mm/1¼"47-49mm x 50mm/1½"47-49mm x 63mm/2"59-61mm x 63mm/2"
111111111111111
19.8919.8919.8919.8923.6323.6327.4027.4028.2328.2331.5631.5635.9835.9842.82
UNIVERSAL TRANSITIONELBOW UTC X POLc/w Metric MDPE Liner
15331543154415531653
15-21mm x 25mm/¾"21-27mm x 25mm/¾"21-27mm x 32mm/1"27-34mm x 25mm/¾"27-34mm x 32mm/1"
11111
19.8919.8923.6323.6323.63
UNIVERSAL TRANSITIONDOUBLE ENDED REPAIR JOINER
1133114411551177116611881199
15-21mm x15-21mm21-27mm x 21-27mm27-34mm x 27-34mm34-39mm x 34-39mm39-43mm x 39-43mm47-49mm x 47-49mm59-61mm x 59-61mm
1111111
19.8919.8923.6331.5631.5635.9842.82
UNIVERSAL TRANSITIONREDUCED REPAIRJOINER
1143115411531165
21-27mm x 15-21mm27-34mm x 21-27mm27-34mm x 15-21mm39-43mm x 27-34mm
1111
19.8923.6323.6331.56
UNIVERSAL TRANSITIONM.I. END CONNECTORUTC X M.I. BSP
1231123212331242124312441252125312541255
15-21mm x ½" BSP15-21mm x ¾" BSP15-21mm x 1" BSP21-27mm x ¾" BSP21-27mm x 1" BSP21-27mm x 1¼" BSP27-34mm x ¾" BSP27-34mm x 1" BSP27-34mm x 1¼" BSP27-34mm x 1½" BSP
1111111111
14.0014.0014.0014.0014.0014.0017.7217.7217.7217.72
PIPE GAUGE*for use with Universal Transition Coupling
113511361137
15-34mm27-43mm43-63mm
111
POAPOAPOA
Guid
e on
ly
Actu
al s
ize d
epen
dant
on
pipe
con
ditio
n.
UTC
RANG
E15
-21m
m21
-27m
m27
-34m
m34
-39m
m39
-43m
m47
-49m
m59
-61m
m
PIPE
CIR
CUM
FERE
NCE
47-6
6mm
68-8
5mm
85-1
07m
m10
7-12
2mm
122-
135m
m14
8-15
4mm
185-
192m
m
Alka
then
e3/
8"1/
2"3/
4"1"
1-¼
"1-
½"
2"
Norm
al G
auge
IRS
134
1/2"
3/4"
1"1-
¼"
Hea
vy G
auge
IRS
135
1/2"
3/4"
1"
Copp
er15
mm
22m
m28
mm
35m
m42
mm
Gal
vani
sed
Iron
3/8"
1/2"
3/4"
1"1-
¼"
1-½
"2"
Stai
nles
s St
eel
3/8"
1/2"
3/4"
1"1-
¼"
1-½
"2"
Met
ric A
BS/P
VC16
mm
& 2
0mm
25m
m32
mm
40m
m
Impe
rial A
BS/P
VC3/
8"1/
2"3/
4"1"
1-¼
"1-
½"
2"
Lead
3/8"
1/2"
3/4"
1-¼
"1"
1-½
"
5lb
(20m
m O
D)6l
b (2
1.6m
m O
D)9l
b (3
0.6m
m O
D)7l
b (3
7.6m
m O
D)16
lb (4
1mm
OD)
12lb
(48m
m O
D)
7lb
(23.
2mm
OD)
11lb
(32.
8mm
OD
)
9lb
(25.
4mm
OD)
1/2"
3/4"
1"1-
¼"
2lb
(16m
m O
D)4l
b (2
5.2m
m O
D)6l
b (3
1mm
OD)
9lb
(39.
2mm
OD)
4lb
(19.
2mm
OD)
5lb
(26.
4mm
OD)
7lb
(31.
6mm
OD)
Fitt
ing
sele
ctio
n ca
n be
mad
e ea
sier
with
use
of t
he P
hilm
ac P
ipe
Gau
ge
Copp
er
If us
er d
oes
not w
ant t
o us
e a
UTC
the
copp
er n
eeds
to b
e M
.I. o
r F.I.
en
ded
so th
at w
e ca
n of
fer a
Met
/Im
p fit
ting
to s
uit.
Sam
e ru
le a
pplie
s fo
r 54
mm
O.D
. cop
per.
Use
copp
er c
ompr
essi
on fi
tting
to a
dapt
to M
.I. o
r F.I.
an
d th
en u
se M
et/I
mp
fittin
g.
Lead
The
gene
ral c
ondi
tion
of le
ad p
ipe
can
mak
e si
zing
diffi
cult
at to
p an
d bo
ttom
tole
ranc
e. If
the
reco
mm
ende
d UT
C is
not
suc
cess
ful t
he n
ext s
ize,
up o
r dow
n, d
epen
ding
on
fit s
houl
d be
offe
red.
See our installation videos on YouTube at Philmac UK
23PHILMAC PRICE GUIDE22 PHILMAC PRICE GUIDE
Fast and Easy Installation
Fast and easy Installation: no pipe preparation is required. Simply insert the pipe into the fitting until the first point of resistance is felt, and then tighten the nut.
Dynamic sealing method: the mechanical advantage of the nut is used to push the O-ring into the compressed position, eliminating the need to push past a seal when inserting the pipe.
No loose components: if the nut should be removed for any reason there is no danger of losing the O-ring, spacer or grip ring as they are retained in the nut. Rated to 16 Bar – ensures the fittings meet the requirements of high pressure systems.
Lead-free: the fittings are made from materials that are lead free.
Installation Instructions
3. Tighten
Tighten the nut by hand, and then with a wrench to the point where the nut is touching the flange on the body of the fitting. Do not tighten beyond this point. * Philmac Spanners availble
1. Cut pipe to length
Cut the pipe square, there is no need to chamfer or lubricate.
2. Insert pipe
Ensure 3 threads are showing and simply slide the pipe in until the point of first resistance is felt
1 2 3
LARGE BORE PE METRIC | INTRODUCTION LARGE BORE PE METRIC | FITTINGS RANGE
Description Part No. Sizes Pks Price
JOINERPOL X POL
818881998100
75mm 90mm 110mm
111
66.2681.19
130.65
REDUCING JOINERPOL X POL
818781988109
75mm x 63mm90mm x 75mm110mm x 90mm
111
65.3485.86
126.24
END CONNECTORPOL X M.I. BSP
8286828882988209
75mm x 2" BSP75mm x 3" BSP90mm x 3" BSP110mm x 4" BSP
1111
43.8646.6750.4184.76
END CONNECTOR 888688988809
75mm x 2" BSP90mm x 3" BSP110mm x 4" BSP
111
42.9450.41
111.99
TEE – EqualPOL X POL
838883998300
75mm90mm110mm
111
94.47131.65261.49
TEEPOL X F.I. BSP
848684988409
75mm x 2" BSP90mm x 3" BSP110mm x 4" BSP
111
90.17102.79189.36
ELBOWPOL X POL
858885998500
75mm90mm110mm
111
104.59126.24214.60
ELBOWPOL X F.I. BSP
868686988609
75mm x 2" BSP90mm x 3" BSP110mm x 4" BSP
111
65.3465.34
111.99
END CAP 808980998009
75mm90mm110mm
111
45.0861.3172.14
FLANGE ADAPTORFlange to BS 4504
7879878709
90mm x 3"110mm x 4"
11
155.66195.03
LARGE BORE KEY ADVANTAGES
22 PHILMAC PRICE GUIDE
25PHILMAC PRICE GUIDE24 PHILMAC PRICE GUIDE
VALVES | INTRODUCTION
VALVES KEY ADVANTAGES
Installation Instructions
Fast and Easy InstallationThreaded or Compression Inlet/Outlet: The different options allow compatibility with existing installations and keeps installation time to a minimum.
Slide and TightenTM Technology: Compression ends incorporate all the benefits of Philmac’s unique technology, which means no force is required to push the pipe past the seal. Simply insert the pipe fully into the fitting and tighten the nut.
Bi-directional flow: The Ball Valves have been designed to work in either direction to ensure easy installation and eliminate the need to look for identification marks.
Multi-position Installation: The valves can be installed in any orientation to assist with all types of installations.
Complete SecurityReliable Operation: High-quality injection moulded components and polypropylene ball means years of reliable operation.
Corrosion Resistant: With a plastic body and components, plus rubber O-rings and a stainless steel handle screw, the components used have a high degree of corrosion resistance.
Positive Open-Close: Rotate through 90° between fully open and fully closed to ensure there is no guesswork required as to weather it is open or closed.
Lead FreeThe Philmac range is completely free from lead.
High Performance MaterialsManufactured from Engineered Materials: Philmac valves are manufactured from lightweight, high performance thermoplastic materials that have excellent impact, UV and corrosion resistance. The materials are non-toxic and taint free.
Complete Coverage Pressure rated 14 bar
Can be installed above or below ground
Complete range Agriculture, Municipal,
Corrosion resistance, long life performance
Manufactured with thermoplastic materials U/V resistant qualities
¼ Turn for visual on/off control
3. Tighten Using a pipe wrench or
multigrips on the end caps only, futher screw the ball valve tight. Where necessary, ensure the thread is held stationary to avoid it from moving. Do not use pipe wrench or multigrips on the body of the valve.
1. Preparation
Apply PTFE tape or approved sealant to the male thread. Sufficient tape needs to be applied to ensure a watertight seal.
2. Assembly
Screw on to a male or female thread by hand until firm.
1 2 3
Long-lasting, corrosion resistance and easy to install, Philmac fittings have proven themselves in irrigation and
commercial applications all over the world. They are the fitting choice for
both contractors and installers.
24 PHILMAC PRICE GUIDE
27PHILMAC PRICE GUIDE26 PHILMAC PRICE GUIDE
Description Part No. Sizes Nominal Bore Pks Price
METRIC/IMPERIALSTOPCOCKPOL X POL
282228332844
20mm/½"25mm/¾"32mm/1"
552
27.7040.9562.52
METRIC/IMPERIALSTOPCOCKPOL X FI
2831283228422843
25mm/¾" x ½"25mm/¾" x ¾"32mm/1" x ¾"32mm/1" x 1"
5522
39.6039.6060.4560.45
METRIC/IMPERIAL¼ TURN BALL VALVE POLX POL
95272953729527395373
20mm/½"25mm/¾"25mm/¾"32mm/1"
1616
19.519.5
1111
36.8338.4646.4750.58
ARCTIC ICE RESISTANTBALL VALVE
803180328033
½"¾"1"
152025
111
20.4624.6535.54
BALL VALVEF.I. X F.I. BSP
5500255003550045500555006
¾" F.I. x ¾" F.I.1" F.I. x 1" F.I.1¼" F.I. x 1¼" F.I.1½" F.I. x 1½" F.I.2" F.I. x 2" F.I.
1619.5263240
11111
30.7842.8855.7065.6084.02
BALL VALVEM.I. X M.I. BSP
5540255403
¾" M.I. x ¾" M.I.1" M.I. x 1" M.I.
1619.5
11
28.3836.60
AIR RELEASEVALVE F.I. BSP
55033 1" BSP 25 1 50.41
FOOT VALVEF.I. BSP
5501255013550145501555016
¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
2227323850
11111
47.0650.6262.2075.32
100.91
Description Part No. Sizes Nominal Bore Pks Price
SINGLE CHECKNON RETURNVALVEF.I. BSP X F.I. BSP
5502255023550245502555026
¾" F.I. x ¾" F.I.1" F.I. x 1" F.I.1¼" F.I. x 1¼" F.I.1½" F.I. x 1½" F.I.2" F.I. x 2" F.I.
2227323850
11111
43.6846.2657.6068.4093.28
DZR DOUBLECHECK VALVEF.I. BSP X F.I. BSPTO BS 6282Back Flow PreventionCategory 3
111011120211303
½" F.I. x ½" F.I.¾" F.I. x ¾" F.I.1" F.I. x 1" F.I.
152025
111
40.8453.5967.52
GM FI X FI STOPCOCK (BS.5433 TYPE20)
25112522253320552066
½" x ½" F.I.¾" x ¾" F.I.1" x 1" F.I.1½" x 1½" F.I.2" x 2" F.I.
11111
50.0267.44
124.60317.49443.58
Description Part No. Sizes Pks Price
METRIC/IMPERIALEND CONNECTORPOL X M.I. BSP
922192229223923192329233924292439244924592539254925592569265926692759276
20mm/½" x ½" BSP20mm/½" x ¾" BSP20mm/½" x 1" BSP25mm/¾" x ½" BSP25mm/¾" x ¾" BSP25mm/¾" x 1" BSP32mm/1" x ¾" BSP32mm/1" x 1" BSP32mm/1" x 1¼" BSP32mm/1" x 1½" BSP40mm/1¼" x 1" BSP40mm/1¼" x 1¼" BSP40mm/1¼" x 1½" BSP40mm/1¼" x 2" BSP50mm/1½" x 1½" BSP50mm/1½" x 2" BSP63mm/2" x 1½" BSP63mm/2" x 2" BSP
101010101010555511111111
4.355.278.355.685.538.838.048.04
16.8116.8118.9218.9221.0524.0420.5523.6428.9428.94
Stopcock
Ball Valve
Metric/Imperial BSP End Connectors (for above Valves)
Liners to suit MDPE pipe are required for WRAS requirements, please see page 11 for these items
VALVES | BACK FLOW PREVENTION & METAL VALVESVALVES | VALVES RANGE
29PHILMAC PRICE GUIDE28 PHILMAC PRICE GUIDE
A TOUGH, CORROSION RESISTANT RANGE OF FITTINGS TO SUITE BSP THREAD STANDARDS
Lead FreeThe Philmac range of Threaded Fittings is completely free from lead.
Complete Coverage
BSP tapered threads
Fully Comprehensive range
Compliments plastic pipelines
Robust threaded fittings
Precision BSP tapered threads
Maximises sealing performance
Corrosion resistant
Versatile range
High performance UV Pesistant materials (Polypropylene)
Quick and simple to install
Reliable installation
½" to 2" products are able to operate at 16 Bar
BSP THREADED FITTINGS | INTRODUCTION
31PHILMAC PRICE GUIDE30 PHILMAC PRICE GUIDE
BSP THREADED FITTINGS | FITTINGS RANGE
Description Part No. Sizes Pks Price
TEE FEMALE 451145224533454445554566
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
101010552
4.215.016.279.84
10.7114.95
ELBOW FEMALE 461146224633464446554666
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
101010552
3.573.854.436.327.56
10.02
ELBOW MALE X FEMALE 469146924693469446954696
½" x ½" BSP¾" x ¾" BSP1" x 1" BSP1¼" x 1¼" BSP1½" x 1½" BSP2" x 2" BSP
101010552
3.473.884.546.327.309.93
PLUG 401140224033404440554066
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
101010101010
1.792.132.493.413.814.93
BUSH – REDUCING 41214131413241414142414341514152415341544161416241634164416541864198
¾" x ½" BSP1" x ½" BSP1" x ¾" BSP1¼" x ½" BSP1¼" x ¾" BSP1¼" x 1" BSP1½" x ½" BSP1½" x ¾" BSP1½" x 1" BSP1½" x 1¼" BSP2" x ½" BSP2" x ¾" BSP2" x 1" BSP2" x 1¼" BSP2" x 1½" BSP3" x 2" BSP4" x 3" BSP
10101010101010101010101010101011
2.332.522.523.593.713.714.294.434.434.436.927.157.157.157.15
21.3241.45
NIPPLE 421142224233424442554266
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
101010555
1.822.082.613.273.865.12
Description Part No. Sizes Pks Price
NIPPLE – REDUCING 422142314232424142424243425142524253425442614262426342644265
¾" x ½" BSP1" x ½" BSP1" x ¾" BSP1¼" x ½" BSP1¼" x ¾" BSP1¼" x 1" BSP1½" x ½" BSP1½" x ¾" BSP1½" x 1" BSP1½" x 1¼" BSP2" x ½" BSP2" x ¾" BSP2" x 1" BSP2" x 1¼" BSP2" x 1½" BSP
101010555555555555
2.383.073.183.763.763.894.694.694.694.636.216.216.216.216.15
SOCKET 431143224333434443554366
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
101010555
3.754.335.378.769.57
13.53
REDUCING SOCKET 4321433143324343435243534354436243634365
¾" x ½" BSP1" x ½" BSP1" x ¾" BSP1¼" x 1" BSP1½" x ¾" BSP1½" x 1" BSP1½" x 1¼" BSP2" x ¾" BSP2" x 1" BSP2" x 1½" BSP
101055555555
4.185.198.478.479.269.269.26
13.0813.0813.08
CAP 490149024903490449054906
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
101010555
3.574.435.015.657.219.01
M.I. BSP HOSE TAILS RXHT15RXHT20RXHT25RXHT32RXHT40RXHT50
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
10101010105
3.453.604.044.354.645.57
IBC SWIVEL-IT ADAPTORS
60UD075B60UD10B60UD20B
2" x ¾" F.I. BSP2" x 1" F.I. BSP2" x 2" F.I. BSP
111
19.4919.4919.49
N.B. All threads are BSP tapered. Use PTFE Tape on threads for lubrication purposes. Do not overtighten.
33PHILMAC PRICE GUIDE32 PHILMAC PRICE GUIDE
SUNDRIES | PRODUCT RANGE BSP THREADED FITTINGS | FITTINGS RANGE
Description Part No. Sizes Pks Price
MALE THREADED TANKCONNECTOR WITHFEMALE INLET
RXTTI15RXTTI20RXTTI25RXTTI32RXTTI40RXTTI50
½" BSP¾" BSP1" BSP1¼" BSP1½" BSP2" BSP
111111
7.037.308.25
10.2713.7916.77
CUT TO SIZE TANKCONNECTOR KITS (PVC)Containing long thread (1 ft long), backnuts (2) and a washer
TCK050TCK075TCK100
½" BSP¾" BSP1" BSP
111
12.9114.9723.26
Description Part No. Sizes Pks Price
HIGH FLOW BALLCOCK - With Nut
RXPTV20RXPTV20LRXPTV20B
¾" standard thread 25mm tail¾" long thread 45mm tail c/w nut¾" long thread 45mm tail bent arm
111
30.2431.9231.10
HIGH FLOW BALLCOCK - Without Nut
RXPTV20RXPTV20LRXPTV20B
¾" standard thread 25mm tail¾" long thread 45mm tail c/w nut¾" long thread 45mm tail bent arm
111
30.2431.9231.10
PIPE CUTTER 17691770
Up to 32mm (Medium)Up to 63mm (Large)
11
48.46142.25
SPANNER 70243170577050
20 - 32mm ‘Y’ spanner (plastic)40 - 63mm ‘Y’ spanner50 - 110mm ‘C’ spanner
111
7.4446.6764.52
PIPE CLIPSSuitable for MDPE pipe
430543064307430843094310431243134314
16mm (oc) 20mm (oc) 25mm (oc) 32mm (cc) 40mm (cc) 50mm (cc)
63mm (cc) 90mm (cc)
110mm (cc)
(oc)openclip (cc)closedclip
101010101010101010
0.951.121.191.321.781.952.445.707.90
SQUEEZE OFF TOOLS MINI2032MIDI2063
20-32mm20-63mm
11
72.42 123.71
PIPE REPAIR KITS To be ordered in multiples of 3 in any size
PRK20PRK25PRK32
PIPE REPAIR KIT 20MMPIPE REPAIR KIT 25MM PIPE REPAIR KIT 32MM
111
25.3426.9844.55
(oc)
(cc)
Pipe Repair KitRepairs Metric/Imperial Damaged Pipe
20mm 1/2"
Contents:1 x Length of pipe
1 x 3G Metric/Imperial Slip Coupling
1 x 3G Metric /Imperial Joiner
4 x Liners
Tel: +44 (0) 1323 847323www.philmac.co.uk Diplocks Way, Hailsham, East Sussex BN27 3JF
Other pack sizes available
Part no. PRK20
Seven into one will go
High Density Class C BS 3284 High Density Class D BS 3284 IRS 136 Heavy Gauge BS 1972/61
Blue MDPE BS 6572 Black MDPE BS 6730 Low Density Class C BS 1972 Low Density Class D BS 1972
philmac header 105 x 60 20mm_ALL AS ONE_FINAL.indd 1 18/04/2017 13:43
NEW
See our installation videos on YouTube at Philmac UK
35PHILMAC PRICE GUIDE34 PHILMAC PRICE GUIDE
| CHEMICAL RESISTANCE CHART
Dynamic sealing method: The mechanical advantage of the nut thread compresses the seal into position, eliminating resistance when inserting the pipe into the fitting so there is no risk of seal distortion or displacement.
No loose components: If the nut is removed there is no danger of losing components, as the collet and seal ring are retained in the body of the fitting. Losing components in the trench becomes a thing of the past.
Designed to minimise pipe twist: The fitting has been designed to minimise pipe twist as the nut is tightened. Maximum pipe twist is approximately a quarter turn compared to one and a half turns with many other fittings. Pipe twist can impact on not only the connection you have just made but also on the connection at the other end of the line.
High performanceMade from advanced thermoplastic materials: 3G Metric/Imperial™ is manufactured from lightweight high performance thermoplastic materials with outstanding impact, UV, chemical and corrosion resistance. The material is non-toxic and taint-free.
Rated to 1600 kpa: Metric/Imperial™ is pressure rated to 16 Bar (230psi) to meet the needs of high pressure systems.
50 year+ design life: Built to withstand the toughest conditions to ensure longevity and durability, Metric/Imperial™ has a 50 year+ design life.
Complete coverageWide range: The Philmac 3G Metric/Imperial™ range is comprehensive: straight and reducing joiners, tees, elbows, end connectors and caps ranging from 20mm to 63mm. Also available are copper connection kits, normal gauge (IRS 134) connection kits, reducing kits and blanking plugs, ball valves, stopcocks, wall plate elbows and tank connectors.
Effect on Water Philmac does not impart to water any odour, taste, colour, or any constituents in concentrations that could be injurious to health.
Philmac complies with: BS 6920 ‘Suitability of non metallic products for use in contact with potable water intended for human consumption with regard to their effect on the water’.
Operating Temperatures: -10°C to +25°C Not suitable for hot water applications.
Fluids other than Water:Pipes connected by Philmac may convey a wide variety of fluids. For resistance to common chemicals consider the following table as a guide only.
For specific applications: please contact our Customer Service Support Centre for advice and information.
Telephone: 0844 335 0016
Facsimile: 0800 590028
34 PHILMAC PRODUCT POCKET GUIDE
CHEMICAL RESISTANCE CHART
CHEMICAL SATISFACTORY NOT SATISFACTORY
Acetone
Alcohol
Ammonium Hydroxide
Antifreeze
Benzene
Butane
Calciuim Salts
Caustic Sode (40% Aqueous)
Chlorine
Citric Acid
Copper Salts
Cresol
Ethylene Alcohol
Ethyl Glycol
Diesel
Formic Acid
Gasoline
Hydrocloric Acid
Kerosene
Methane
Methlene Chloride
Mineral Oils
Nitric Acid
Petroleum Oil
Sewerage
Sodium Cyanide
Sulphuric Acid
Toluene
Turpentine
Transformer Oil
Zinc Salt Solution
37PHILMAC PRICE GUIDE36 PHILMAC PRICE GUIDE
| PHILMAC UK CUSTOMER SERVICES
Mark CulshawNorth West, North Wales
07787 105342 [email protected]
Matt Prole South Wales and South West
07771 954477 [email protected]
South, South East & London
07795 302102 [email protected]
Stephen Jeffery
Jon ClarkMidlands, East Midlands
07885 281439 [email protected]
Barry McKibbinScotland, NI and Export
07909 004560 [email protected]
North Midlands
South WestSouth East
Tues, wed
Mon, Tues, Thurs
Mon, Fri
Mon, Wed, Thurs
Tues, Thurs
Wed, Fri
Mon, Tues, Wed
Tues, Thurs, Fri
Mon, Wed, Fri
Mon, Thurs
Tues, Fri
Mon, Thurs, Fri
Tues, Wed, Thurs
Mon, Wed
Tues, Wed, Fri
Mon, Tues, Fri
Tues
Thursday friday
Monday and tuesday
Daily
On rquest
KW
KW
AL
B
BA
BB
BD
BHDT
BL
BN
BS
CA
CB
C F
CH
CM
CO
CT
C V
CW
DA
DD
AB
DE
DG
DH
D L
DN
D Y
EH
EX
GL
GU
H D
H G
H P
HR
H UH X
IP
IV
KA
KYKY
L
LA
LD
LL
LN
LS
LU
M
ME
MK
ML
N EN E
NG
NN
N P
N R
O L
F K
OX
PAPA
PAPA
PE
PHPH
PL
PO
PR
RH
RM
S
SA
SG
SK
SNRG
SOSP
SR
FY
SS
ST
SY
T A
TTD
T F
T N
T Q
G
T R
LE
T ST S
W A
W F
W N
WR
WSW V
YO
BRC R
E
EC
EN
HAIG
KT
NN W
SESL
SM
SWT W
U B W
W C
W D
LONDON
Scotland
Get in touch with our customer service and enquiry team by phone, fax or email:
Tel No: 0844 335 0016
Fax: 0800 590028
Email: [email protected]
Area Sales Managers
39PHILMAC PRICE GUIDE38 PHILMAC PRICE GUIDE
| NOTES
41PHILMAC PRICE GUIDE40 PHILMAC PRICE GUIDE
| NOTES
43PHILMAC PRICE GUIDE42 PHILMAC PRICE GUIDE
| T&CS
PHILMAC CONDITIONS OF SALE
1. DEFINITIONS: ‘Seller’ shall mean Glynwed Pipe Systems Limited, registered in England under number 1698059. ‘Buyer’ shall mean any company, organisation or individual to whom a quotation is offered, or whose order is accepted by the Seller.
2. CONDITIONS: All offers, quotations, estimates, acceptances and contracts are subject to these Conditions of Business and any terms or conditions which any other person shall seek to impose or make part of any contract shall, so far as is inconsistent with these Conditions of Business, not apply unless expressly agreed by the Seller in writing. The headings in these conditions are for convenience only and shall not affect their interpretation.
3. QUOTATIONS AND PRICE VARIATION: a) Any quotation given by the Seller is an invitation to the Buyer to make an offer only and no order of the Buyer placed with the Seller in pursuance of a quotation or otherwise shall be binding on the Seller unless and until it is accepted in writing by the Seller.b) Unless stated otherwise, all quotations and published price lists are ex works, exclusive of VAT and shall remain valid for 30 days or such a period as may be quoted but nevertheless the Seller may amend or withdraw any quotation by written or oral notice. Quotations may be varied if the Buyer makes variations in his specifications.c) Certain products are denoted ‘MTO’ in the Seller’s published price lists. These products are Made to Order Goods and the Seller manufactures or procures these goods on a bespoke basis only. Where a Buyer has made an offer for ‘MTO’ products that the Seller has accepted in writing the Buyer forfeits their right to cancel their offer unless the Seller confirms in writing that it will accept cancellation by the Buyer. Where the Seller does not provide written confirmation of the Buyer’s cancellation the Buyer remains liable for the full contractual value of all ‘MTO’ products. ‘MTO’ ‘Call-Off’ orders must be taken within 12 months of the original order date.
4. STATEMENTS OR REPRESENTATIONS TO THE BUYER: If any statement or representation has been made to the Buyer upon which the Buyer relies other than in the documents enclosed with the Seller’s quotation, the Buyer must set out that statement or representation in a document to be attached to or endorsed on the order in which case the Seller may submit a new quotation.
5. DELIVERY - TIME: a) Any period for delivery given at any time and in any manner by the Seller is an estimate only and is not binding on the Seller. Delivery periods are normally calculated from the later of:
i) acceptance of order; orii) where applicable, the receipt by the Seller of a detailed specification or drawings.b) Time shall not be deemed to be of the essence of the contract. Failure by the Seller to meet any quoted delivery period for any part or the whole of the order shall not entitle the Buyer to rescind the contract or to claim damages of any nature.
c) The Seller will endeavour to comply with reasonable requests by the Buyer for postponement of delivery but shall be under no obligation to do so. Where delivery is postponed otherwise than due to default by the Seller the Buyer shall pay all costs and expenses including a reasonable charge for storage and transportation occasioned thereby and an extra charge for split delivery if applicable.d) The Buyer will receive delivery of any consignment between the hours of 8.00am and 4.00pm Monday to Friday inclusive, unless otherwise agreed in writing. Cost incurred by the Seller arising from the Buyer’s refusal to accept consignments within the agreed hours shall be borne by the Buyer.
6. DELIVERY AND RISK: a) Except where stated to the contrary in the contract, delivery shall be made as follows:
i) where the Buyer provides the transport, delivery shall be made ex the Seller’s works;ii) where the Seller provides the transport, delivery shall be made to the premises of theBuyer, or the premises of the Buyer’s customer or works site if the Buyer has requested delivery to be so made but where the Buyer has made such a request the Seller will make a first delivery to the Buyer’s customer or works site as so much of the goods as is available for that delivery but subsequent deliveries will be made to the premises of the Buyer.
b) The Seller may at its discretion make partial delivery of orders and invoice the same.c) Risk in the goods shall pass on delivery.d) Where goods are sent FOB the Seller’s responsibility shall cease when the goods are placed on board ship or aircraft without the need for the Seller to give notice to the Buyer and the provisions of Section 32(3) of the Sale of Goods Act 1979 shall not apply.
7. OWNERSHIP OF GOODS:a) The goods shall remain the sole and absolute property of the Seller as legal and equitable owner until such time as the Buyer shall have paid to the Seller the contract price together with the full price of any other goods the subject of any contract between the Seller and the Buyer.b) The Buyer acknowledges that until such time as the property in the goods passes to the Buyer he is in possession of the goods as a bailee and fiduciary agent for the Seller and the Purchaser shall store the goods in such a manner that they are clearly identifiable as the property of the Seller.c) Until payment due under all contracts between the Buyer and the Seller had been made in full, in the event of sale of the goods by the Buyer:
i) the Seller shall be entitled to trace all proceeds of sale received by the Buyer through any bank or other account maintained by the Buyer; andii) the Buyer shall if requested by the Seller in writing to so assign its rights to recover the selling price of the goods from the third parties concerned. Such monies to be held separately by the Buyer as agent on behalf of the Seller.
d) The Seller may for the purpose of recovery of its goods enter upon any premises where they are stored or where they are reasonably thought to be stored and may repossess the same.
8. TERMS OF PAYMENT: In the event of default in payment according to the agreed payment terms between the Seller and the Buyer – ie: by the end of the month following the month of despatch of the goods the Seller shall be entitled without prejudice to any other right or remedy to suspend all further deliveries and to charge interest on any amount outstanding at the rate of 2% per month until payment in full is made (a part of a month being treated as a full month for the purpose of calculating interest).
9. SHORTAGES AND DEFECTS APPARENT ON DELIVERY: a) It shall be the responsibility of the Buyer to inspect or arrange for an inspection of the goods on delivery whether the goods are delivered to the Buyer’s premises or to the premises of the Buyer’s customer or to a works site. If no such inspection is made the Buyer shall be deemed to have accepted the goods. b) The Buyer shall have no claim for shortages or defects apparent on inspection unless:
i) a written complaint is made to the Seller within three days of receipt of the goods specifying the shortage or defect; andii) the Seller is within seven days of receipt of the complaint given an opportunity to inspect the goods and investigate the complaint before any use is made of the goods.
c) If a complaint is not made to the Seller as herein provided then in respect of such shortages or defects the goods shall be deemed to be in all respects in accordance with the contract and the Buyer shall be bound to pay for the same accordingly.
10. CLAIMS FOR DEFECTS NOT APPARENT ON INSPECTION: a) The Buyer shall have no claim for defects not apparent on inspection unless the Seller is notified of defective workmanship or materials within twelve months from delivery of the goods. Provided that the goods have been installed and applied in accordance with any relevant recommendations made by the Seller, the Seller will at its option replace the goods or refund the net invoiced price in respect of the goods which have been shown to be defective. If the Seller does so supply substitute goods the Buyer shall be bound to accept such substituted goods in full satisfaction of the obligations of the Seller under the contract. b) The Buyer shall in any event have no claim or set-off in respect of defects unless a written complaint is sent to the Seller as soon as the defect is noticed and no use is made of the goods thereafter or alteration made thereto by the Buyer before the Seller is given an opportunity to inspect the goods. c) The Buyer is responsible for ensuring that the goods are fit for any particular purpose, and no warranty or condition of fitness for any particular purpose is to be implied into the contract.
11. LIABILITY: Save as stated in Conditions 9 and 10 (and save in respect of death or personal injury resulting from the negligence of the Seller its servants or agents) the Seller shall not be liable for any claim or claims for direct or indirect consequential or incidental injury loss or damage made by the Buyer against the Seller whether in contract or in tort (including negligence on the part of the Seller its servants or agents) arising out of or in connection with any defect in the goods or their fitness or otherwise for any particular purpose or any act omission neglect or default of the Seller its servants or agents in the performance of the contract.
12. FORCE MAJEURE: Notwithstanding anything herein contained neither the Buyer nor the Seller is to be held liable for any delay or failure to carry out the contract due wholly or in part to an act of God action by any Government whether British or foreign civil war strikes and/or lockouts wheresoever occurring fire trade disputes floods or unfavourable weather or any material becoming unavailable or irreplaceable (whether at all or at commercially acceptable prices) or any other circumstances beyond the control of the Seller.
13. SUB-CONTRACTING: The Seller reserves the right to sub-contract the fulfilment of any order or any part thereof.
14. INSOLVENCY AND BREACH OF CONTRACT: In the event that: a) the Buyer commits any breach of the contract and fails to remedy such breach (if capable of remedy) within a period of thirty days from receipt of a notice in writing from the Seller requesting such remedy; or b) any distress or execution is levied upon any of the goods or property of the Buyer; or c) the Buyer offers to make any arrangements with or for the benefit of its creditors or (if an individual) becomes subject to a petition for a bankruptcy order or (being a limited company) has a receiver appointed of the whole or any part of its undertaking property or assets; or d) an order is made or a resolution is passed or analogous proceedings are taken for the winding up of the Buyer (save for the purpose of reconstruction or amalgamation with insolvency and previously approved in writing by the Seller) the Seller shall thereupon be entitled without prejudice to its other rights hereunder forthwith to suspend all further deliveries until the default has been made good or to determine the contract and any unfulfilled part thereof or at the Seller’s option to make partial deliveries. Notwithstanding any such termination the Buyer shall pay to the Seller at the contract rate for all the goods delivered up to and including the date of termination.
15. INDUSTRIAL PROPERTY RIGHTS: If goods supplied by the Seller to the Buyer’s design or specifications infringe or are alleged to infringe any patent or registered design right or copyright the Buyer will indemnify the Seller against all damages, costs and expenses incurred by the Seller as a result of the infringement or allegation. The Buyer will give the Seller all possible help in meeting any infringement claim brought against the Seller.
16. BUYER’S ERROR IN ORDERING: In the event the Buyer orders incorrectly the Seller will be under no obligation to the Buyer to rectify or assist in rectifying the error.
17. LAW AND JURISDICTION: The contract shall be subject in all respects to English Law and to the jurisdiction of the English Courts.
Distributor:
1 Swaffield Park
Hyssop Close
Cannock
WS11 7FU
United Kingdom
Tel: 0844 335 0016 Fax: +44 (0) 800 590028Email: [email protected]
www.philmac.co.uk
Glynwed Pipe Systems Ltd T/A PhilmacRegistered in England 1698059Registered Office: Dickley Lane, Lenham, Maidstone, Kent ME17 2DE
J41745 Philmac Price List_Final_A4_cover pages.indd 1 13/03/2018 17:23