TOYOTA TUNDRA 2007 DASH APPLIQUE Part Number ...toyotaparts.sparkstoyota.com/install/00016-34710inst.pdfTundraD-Cab and Super Maxwith BucketSeats Recommended Sequence of Application

TOYOTA TUNDRA 2007- DASH APPLIQUEPart Number:07 Tundra Base Kit (8 pc.) 00016-3471007 Tundra D-Cab Rear Doors 00016-3471107 Tundra Super Max Rear Doors 00016-34712Accessory Code: DM2

Kit Contents Quantity Reqd.Item

#Description

BaseKit

D-CabDoors

Super MaxDoors

1 Speedo 12 Shifter 13 Cup holder 14 Storage 15 LH Vent 16 RH Vent 17 Drivers door 18 Passengers Door 19 D-Cab LH Rear

Door1

10 D-Cab RH Rear Door

1

11 Super Max LHRear Door

1

12 Super Max RHRear Door

1

Hardware Bag Contents Item # Quantity Reqd. Description1

Additional Items Required For Installation Item # Quantity Reqd. Description

ConflictsNote:

Recommended Tools Safety Tools Hand Protection Latex GlovesVehicle Protection Seat/Floor Covers Special Tools

Installation ToolsHeat Source Lint-Free Scratch Resistant ClothNylon Prying Tool

Special ChemicalsAlcohol & Water

Color Applicability/Trim Level

Accesso ryC olor

Vehicle/Trim Color

General Applicability Tundra D-Cab and Super Max with Bucket Seats

Recommended Sequence of Application Item # Accessory1 Install Security/Audio2 Install Molded Dash3

*MandatoryLegend

STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with.OPERATOR SAFETY: Use caution to avoid risk of injuryCRITICAL PROCESS: Proceed with caution to ensure a quality installation. These points will be audited on a completed vehicle installationTOOLS & EQUIPMENT: This calls out the specifictools and equipment required for this processREVISION MARK: This mark highlights a change in installation with respect to previous issue.

SPECIAL NOTE:After TMS and Safety mandated preparatory steps have been taken, the installation sequence is the suggested method for completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessoryinstallation. Unless otherwise stated in the document, the associates may perform the installation steps in any order to make the installation as efficient as possible while maintaining consistent quality.

Southeast Toyota Distributors, LLC Page 1 of 9

Non-Intrusive IR Temp Probe/Gun

Promoter (Optional)

iustyfaText BoxDocument: 15.32.00 PIO / DIO 01/03/07

Document: Installation Instructions TOYOTA TUNDRA 2007 DASH APPLIQUE

A. Follow these installation precautions

1. Use Seat and Floor Protectors to avoid damage to surfaces. (Figure A1)

STOP

Figure A1 2. Wear protective latex gloves while cleaning factory panels. NOTE: The use of protective latex gloves during cleaning is mentioned as a precaution to those installers who may be sensitive to the chemicals being used in this process. The use of protective gloves is not mandatory.

Figure A2

Figure A4

Figure A3

3. Use clean lint-free scratch resistant cloths for cleaning factory components. (Figure A2)

STOP

4. Do not spray cleaning solutions directly on factory dash surfaces. (Figure A3)

STOP

5. Clean surface thoroughly & wipe dry immediately with a new clean cloth. (Figure A4)

6. Vehicle dash surfaces must be at between 70°F & 110°F just before actual installation.

7. Dash appliqué must be between 70°F & 110°F just before actual installation. All dash appliqué should be flush to edge of factory components +/-1.0mm

8. Use pull-tabs to remove 3M liners. Do not touch adhesive backing before installation. (Figure A5)


iustyfaText BoxFigure A 5

Document: Installation Instructions

TOYOTA TUNDRA 2007 DASH APPLIQUE

Figure A5

B. Inspection of Parts 07 Tundra Base Kit (8 pc.)1. Inspect parts prior to installation to avoid

unnecessary removal.

C. Dry Fit Parts

1. Check placement for alignment of each part.

D. Clean Factory Surfaces

1. Use latex gloves to protect hands. Notmandatory, only for those installers who maybe sensitive to the chemicals being used.

Figure D12. Apply alcohol & water using a lint free cloth

that is scratch resistant.

i. Thoroughly clean all surfaces shown. (Figure D1, D2 or D3)

07 Tundra D-Cab Rear Doors (2 pc.)

ii. Dry with another clean, dry cloth.(Figure D1, D2 or D3)

Figure D2

- Latex Gloves - Clean Cloths - Alcohol & Water


07 Tundra Super Max Rear Doors (2pc)

iustyfaText BoxFigure D3



Part AFigure E1

E. Install Speedo 1. To warm up vehicle surfaces:

Use heat gun, infrared lamps, shop heat or vehicle heating system to heat surfaces to a temperature of at least 70°F. Keep heat gun at lowest setting, 6” from surfaces.

2. Lower the steering column to the lowest position.

3. Remove adhesive liners from part. 4. Position and secure part.

i. Align cut outs for all switches, vents and dials

ii. Align part uniformly to edge of factory component. (Figure E1)

Speedo Surround

iii. Gently touch part into position. iiii. Verify function of all switches dials and

vents

Part B Figure F1

- Heating System4. Press firmly into place. Roll fingertips in a back and forth motion to set adhesive. Be sure to roll thumb along outside and inside edges while applying pressure.

F. Install Shifter 1. Follow steps to warm components as required 2. Remove adhesive liners from part. 3. Position and secure part.

i. Align cut outs for the storage opening and the shift channel opening. (Figure F1)

ii. Align part uniformly to the bottom edge of the abutting speedo surround

iii. Align part uniformly to the core 4. Verify function of all dials and buttons. 5. Press firmly into place. Roll fingertips in a

back and forth motion to set adhesive. Be sureto roll thumb along outside and inside edges while applying pressure.

Shifter




- Heating System

Figure H1

Figure H1

Figure J1

Part F

Cup holder

Part E

Storage

- Heating System

- Heating System

Figure H1

LH Vent

Part CFigure I1

Figure G1 G. Install Cup holder 1. Follow steps to warm components as required. 2. Remove abutting center storage lid and set

aside3. Remove adhesive liners from part. 4. Position and secure part.

i. Align cup holder openings.ii. Align part uniformly to edge of factory

component. (G1) iii. Press all edges with your palm so they fit

into the crevice.5. Press firmly into place. Roll fingertips in a

back and forth motion to set adhesive. Be sure to roll thumb along outside and inside edges while applying pressure.

6. Replace center storage lid.

H. Install Storage Lid 1. Follow steps to warm components as required. 2. Remove adhesive liners from part. 3. Position and secure part.

i. Align part uniformly to edge of factory component. (Figure H1)

ii. Gently touch part into position. 4. Verify alignment.5. Press firmly into place. Roll fingertips in a


ALTHOUGH THE LEFT AND RIGHT VENT LOOK VERY SIMILAR THEY ARE DIFFERENT. VERIFY THAT YOU ARE INSTALLING THE CORRECT PART

STOP

I. Install LH Vent1. Follow steps to warm components as required. 2. Remove adhesive liners from part. 3. Position and secure part.

i. Align vent wheel and vent opening ii. Align part uniformly to edge of

factory component. (Figure I1) iii. Gently touch part into position.



4. Press firmly into place. Roll fingertips in a back and forth motion to set adhesive. Be sure to roll thumb along outside and inside edges while applying pressure.

- Heating System

J. Install RH Vent Part Digure J1 1. Follow steps to warm components as required.


i. Align vent wheel and vent opening ii. Align part uniformly to edge of

factory component. (Figure J1) iii. Gently touch part into position.

4. Press firmly into place. Roll fingertips in a back and forth motion to set adhesive. Be sure to roll thumb along outside and inside edges while applying pressure.

K. Install Drivers Door

1. To warm up vehicle surfaces: i. Use heat gun, infrared lamps, shop

heat or vehicle heating system to heat surfaces to a temperature of at least 70°F. Keep heat gun at lowest setting, 6” from surfaces.


i. Align cut outs for window and door lock switches.

ii. Align part uniformly to edge of factory component. (Figure K1)

iii.Gently touch part into position. iv. Verify function of window and door

lock switches. v. Verify function of storage door below

door pod 4. Press firmly into place. Roll fingertips in a

back and forth motion to set adhesive. Be sure


F

- Heating System

RH Vent

Part Gigure K1
F
Drivers Door

- Heating System


to roll thumb along outside and inside edges while applying pressure.

Part Higure L1

Passengers Door

L. Install Passenger Door

1. To warm up vehicle surfaces: (1) Use heat gun, infrared lamps, shop



(1) Align cut outs for window and door lock switches.

(2) Align part uniformly to edge of factory component. (Figure L1)

- Heating System

(3) Gently touch part into position. (4) Verify function of window and door

lock switches. (5) Verify function of storage door below



M. Install LH Rear Door (D Cab or Super Max) Part Ligure M1 1. To warm up vehicle surfaces:

(1) Use heat gun, infrared lamps, shop heat or vehicle heating system to heat surfaces to a temperature of at least 70°F. Keep heat gun at lowest setting, 6” from surfaces.


(1) Align cut outs for window switch. (2) Align part uniformly to edge of factory

component. (Figure M1) (3) Gently touch part into position. (4) Verify function of window switch. (5) Verify function of storage door below


back and forth motion to set adhesive. Be sure

Southeast Toyota Distributors, LLC Page 7 of

F

F

LH Rear Door

- Heating System

9


to roll thumb along outside and inside edges while applying pressure.

N. Install RH Rear Door (D Cab or Super Max)

Part KFigure N1

RH Rear Door

1. To warm up vehicle surfaces: (1) Use heat gun, infrared lamps, shop



(1) Align cut outs for window switch. (2) Align part uniformly to edge of factory

component. (Figure N1) (3) Gently touch part into position. (4) Verify function of window switch. (5) Verify function of storage door below



J. Clean Up 1. Wipe down all surfaces to remove any finger prints or etc… 2. Place Care Card in glove box. 3. Remove protective covers from vehicle interior.


TOYOTA TUNDRA 2007- WOOD TRIM Section III – Functional Verifications Section III – Functional Verifications Check: Look For:

Full movement, back and forth

Full movement, back and forth

Full rotation, up and down

Full Movement through channel

Full rotation of dail

Full movement, in out

Full movement, in out

Applique should be flush to edge of factory component, +/- 1.0mm

Window Switch Buttons

Door Lock Buttons

A/C Vent

Shifter Channel

Climate Control

Hazard Button

Door Storage Compartments

Gap


Documents

TOYOTA TUNDRA 2007 DASH APPLIQUE Part Number ...toyotaparts.sparkstoyota.com/install/00016-34710inst.pdfTundraD-Cab and Super Maxwith BucketSeats Recommended Sequence of Application