TOSIBOX connection to PLC and Operator panel KI00364 … sprava/Tosibox/Startup TOSIB… · TOSIBOX connection to PLC and Operator panel KI00364 2014-06 3 Table of Contents . 1 Function

Copyright © Beijer Electronics, 2014 This documentation (below referred to as ‘the material’) is the property of Beijer Electronics. The holder or user has a non-exclusive right to use the material. The holder is not allowed to distribute the material to anyone outside his/her organization except in cases where the material is part of a system that is supplied by the holder to his/her customer. The material may only be used with products or software supplied by Beijer Electronics. Beijer Electronics assumes no responsibility for any defects in the material, or for any consequences that might arise from the use of the material. It is the responsibility of the holder to ensure that any systems, for whatever applications, which is based on or includes the material (whether in its entirety or in parts), meets the expected properties or functional requirements. Beijer Electronics has no obligation to supply the holder with updated versions.

TOSIBOX connection to PLC and Operator panel KI00364 2014-06

1 Function and area of use This document describes how to build up a connection from PC with Tosibox Key via internet, Tosibox Lock to PLC or operator panel.

2 About this Start Up document

This Start Up document should not be considered as a complete manual. It is an aid to be able to start up a normal application quickly and easily.

Use the following software and drivers in order to obtain a stable application: In this document we have used following software • GX Works2 ver 1.501X • FX Conigurator EN 1.40 • E-Designer 7.52 • iX Developer 2.10 • CODESYS V3.5 SP4+

In this document we have used following hardware • TOSIBOX Lock, TOSIBOX Key • MELSEC FX3U: FX3U-ENET, FX3U-ENET-ADP • MELSEC Q03UDE • iX panel / E1000 panel

1 (33)

Beijer Electronics Automation AB − a Beijer Electronics Group company

Head Office Subsidiaries Beijer Electronics Automation AB Norway, Drammen: Beijer Electronics AS, +47 32 24 30 00 P.O. Box 426, Stora Varvsgatan 13a Finland, Vantaa: Beijer Electronics Oy, +358 207 46 35 00 SE-201 24 Malmö, SWEDEN Denmark, Roskilde: Beijer Electronics A/S, +45 75 76 66 Telephone +46 40 35 86 00 Estonia, Tallinn: Beijer Electronics Eesti Oü, +372 6 518140 Fax +46 40 93 23 01 Latvia, Riga: Beijer Electronics SIA, +371 6 7842280 Lithuania, Kaunas: Beijer Electronics UAB, +370 5 2323101

Reg no. 556701-3965 VAT no SE556701396501 www.beijer.se [email protected]

KI_e

ng_1

3053

1.do

t, 13

0103


For further information we refer to • TOSIBOX user manual (tosibox homepage) • Start Up document for FX3U-ENET, (KI00254) • Start Up document for MELSEC QnUDE(H) with built-in ethernet port (KI00278) • Start Up document how to download a project to an E1000-terminal (KI00255/KI00263) • Manuals for the PLC and iX / E1000 panel can be find at http://www.beijer.se/

This document and other Start Up documents can be obtained from our homepage. Please use the address manual@ beijer.se for feedback on our Start Up documents.

www.beijer.se 2 (33) KI_e

ng_1

3053

1.do

t, 07

0221

http://www.tosibox.com/support/

http://www.beijer.se/web/web_se_be_se.nsf/docsbycodename/filearchive?OpenDocument&mylink=/web/BexFilePileAUT.nsf/fm.be.searchframe?openform&Lang=SE&DocID=59D5DF437BC35A7EC125728E005C241A

http://www.beijer.se/web/web_se_be_se.nsf/docsbycodename/filearchive?OpenDocument&mylink=/web/BexFilePileAUT.nsf/fm.be.searchframe?openform&Lang=SE&DocID=EA784C4B15C0DD6CC12574E5002D9D29

http://www.beijer.se/web/web_se_be_se.nsf/docsbycodename/filearchive?OpenDocument&mylink=/web/BexFilePileAUT.nsf/fm.be.searchframe?openform&Lang=SE&DocID=0C95F48049BF7508C125728E005AE598

http://www.beijer.se/


3 Table of Contents 1 Function and area of use .................................................................................................................................................. 1

2 About this Start Up document ......................................................................................................................................... 1

3 Table of Contents .............................................................................................................................................................. 3

4 First step ............................................................................................................................................................................ 3

5 Tosibox products and accesories ...................................................................................................................................... 3

6 Connection types and Setup of Tosibox and Key ........................................................................................................... 4 6.1 Connection types ........................................................................................................................................................ 4 6.2 Serialization of Tosibox Key and Lock ....................................................................................................................... 6

7 Application example (Mode B)......................................................................................................................................... 7 7.1 Connecting to MELSEC FX3U (FX3U-ENET-ADP).................................................................................................. 7 7.2 Connecting to MELSEC FX3U (FX3U-ENET) ......................................................................................................... 12 7.3 Connecting to MELSEC Q03UDE (ethernet port on cpu) ........................................................................................ 15 7.4 Connecting to E1000 ................................................................................................................................................ 18 7.5 Connecting to iX T7B SoftControl ............................................................................................................................ 21

8 Application example (Mode A) ...................................................................................................................................... 24 8.1 Connecting to Mitsubishi FX3U-ENET-ADP ........................................................................................................... 24

9 Appendix .......................................................................................................................................................................... 27 9.1 Tosibox Lock Service port and Web interface .......................................................................................................... 27 9.2 FAQ .......................................................................................................................................................................... 33

4 First step For best understanding and easy working with Tosibox we recommend: - Basic knowledge of Internet connection type WAN and LAN network. - Prepare the computer with the programming tools for the PLC and HMI. - Download StartUp document for the PLC and HMI.

Note! When changing parameters in Tosibox Lock, processing time can take up to 60 seconds.

5 Tosibox products and accesories

Tosibox Lock Tosibox Key USB Cable

Ethernet Cable AC Adapter Antennas ( 2 )


ng_1

3053

1.do

t, 07

0221


6 Connection types and Setup of Tosibox and Key

6.1 Connection types

Mode A (default setting)

• Lock joins an existing network as a client (one cable only). • Lock will find all network devices (static and dynamic/leased IP adresses) • Access can be limited with MAC/IP filtering

Setup options: - DHCP Client mode (just one cable to LAN3 port) - Existing network DHCP server provides the IP address for TOSIBOX

Consider the data security! - The user of the Key has access to all devices in the local network! - In case access rights need to be restricted, initiate MAC filtering (Industry-setting) or use Mode B.


ng_1

3053

1.do

t, 07

0221


Mode B (most customers use Mode B)

• In Mode B, the Lock creates its own protected local network for the connected devices. Only these devices, connected to the Lock directly by cable or WiFi, are accessible with the Key

• Lock switches automatically into Mode B when it is connected to the Internet via WAN port, 3G modem or Wifi

WAN connection options: - Broadband (WAN connection) - Modem (2G, 3G or 4G) can be purchased separately from Tosibox

LAN Connections options: - Device is in Client mode (TOSIBOX default setting, DHCP mode). TOSIBOX provide IP address. The device (adapter, PLC, Camera have to be in Client mode) - Fixed IP address in the device (TOSIBOX default settings, DHCP mode). Use TOSIBOX fixed IP address slot (10 IP addresses upwards, starting from TOSIBOX default IP - Fixed (already defined by customer) IP address in the device. TOSIBOX LAN IP adress will be canged to same range than fixed IP address.


ng_1

3053

1.do

t, 07

0221


6.2 Serialization of Tosibox Key and Lock

• Power ON to the Tosibox Lock • Wait 2 minutes

• Serialize the Tosibox Key by inserting the key in the USB port • When the LED goes OFF the Key are ready to use

• Power ON and wait 2 minutes

Note! To handle extra Keys and Sub key, read the manual “TOSIBOX Users maual”

Wait 2 minutes for the device to

power up

When blinking has stopped, Key & Lock are serialized (10 sec)


ng_1

3053

1.do

t, 07

0221


7 Application example (Mode B)

7.1 Connecting to MELSEC FX3U (FX3U-ENET-ADP) In this example we like to programming and monitor the FX3U from a PC with GX Works2. We have to setup the Tosibox in “Mode B”, configure the LAN-port and FX3U-ENET-ADP.

7.1.1 Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Use Firefox to get best layout in setup! Connect the computer to the TOSIBOX LOCK´s “Service” Port. Type “http://laite.Tosibox” or “172.17.17.17” into the web browser. The user ID is ”admin” and the password is visible in the bottom of the TOSIBOX LOCK. Note! The internet connection in the PC should have DHCP (receives an IP address automatically). After setup

PC with Tosibox Key FX3U-ENET-ADP (left side module)

Tosibox Lock

INTERNET

Tosibox Key

LAN1-3 WAN

192.168.1.20

LAN IP: 192.168.1.100 LAN (1-3) address ranges Static: 192.168.1.1-192.168.1.99 192.168.1.111-192.168.1.254 DHCP: 192.168.1.101- 192.168.1.110

WAN-port IP: from DHCP server in network

PC get the IP from LAN / DHCP 192.168.1.101- 192.168.1.110


ng_1

3053

1.do

t, 07

0221


• Go to “Network” / “LAN”

Set the address to 192.168.1.100 and the netmask to 255.255.255.0

• Set the LAN DHCP Server

The LAN IP are set to 192.168.1.100 and the setup config the first adress to 192.168.1.101 and 10 address forward to 192.168.1.111. There will be 10 DHCP adresses in this network: 192.168.1.101 to 192.168.1.111.

• Set the WAN to DHCP Client


ng_1

3053

1.do

t, 07

0221


• Go to the “Status” and Network devices.

Set the controlled device´s (FX3U-ENET-ADP in this example) IP address to 192.168.1.20

• Click on “New network devices” and the “New device” popup

NOTE! You can also use the ”Scan for LAN devices” to find the devices in the same network.

• Click on the ”write” sympol and edit the device


ng_1

3053

1.do

t, 07

0221


7.1.2 Connect the computer to FX3U-ENET-ADP

The computer must be connected to “Internet” in another network than the Tosibox! • Connect the Tosibox Key to USB port at the computer and the Tosibox software* will

start. A dialog is shown to select to use “Password”. Password is recommend. * The Tosibox software will be installed the first time you connect “Tosibox Key” to the computer.

• Enter the user interface through double-clicking on the Tosibox Lock in the software window

Network device show up under "Network devices". Now you should be able to connect the programming software (GX Works2) to FX3U. Note! Before connection with Tosibox you have to setup the PLC (FX3U) in direct connection (PC --- “SC09” --- FX3U prog.port).


ng_1

3053

1.do

t, 07

0221


7.1.3 Setup Ethernet modul FX3U-ENET-ADP in GX Works2

• Start a new project (FX3U) and setup the ethernet port

• The default setting for “Open Setting” are 4 programming connection • Setup the communication with the ethernet modul in GX Works2


ng_1

3053

1.do

t, 07

0221



Tosibox Lock

INTERNET

Tosibox Key

LAN1-3 WAN

192.168.1.20 FX3U-ENET (right side module)

192.168.1.21

7.2 Connecting to MELSEC FX3U (FX3U-ENET) In this example we like to programming and monitor the FX3U from a PC with GX Works2. We have to setup the Tosibox Lock in “Mode B”, configure the LAN-port and FX3U-ENET.

7.2.1 Setup Tosibox in Mode B See chapter: Setup Tosibox in Mode B and connect to FX3U-ENET-ADP Below you find what´s different. • Go to “Network” / “LAN”

• Click on the ”write” sympol and edit the device


ng_1

3053

1.do

t, 07

0221


See chapter: Connect the computer to FX3U-ENET-ADP • Enter the user interface through double-clicking on the Tosibox Lock in the software

window


ng_1

3053

1.do

t, 07

0221


7.2.2 Setup Ethernet modul FX3U-ENET with FX Configurator EN

• Start “FX Configurator EN” • Select Module 0 (first special module on right side of the main unit) • Click at “Operational settings” and configure the module

• Click “Open Setting” and set one MELSOFT connection (for programming) • Setup the communication to the ethernet modul in GX Works2


ng_1

3053

1.do

t, 07

0221


Q03UDE CPU-ethernet port


Tosibox Lock

INTERNET

Tosibox Key

LAN1-3 WAN

192.168.1.20

192.168.1.30

FX3U-ENET (right side module)

192.168.1.21

7.3 Connecting to MELSEC Q03UDE (ethernet port on cpu) In this example we like to programming and monitor the Q03UDE from a PC with GX Works2. We have to setup the Tosibox Lock in “Mode B”, configure the LAN-port and Q03UDE-CPU.



ng_1

3053

1.do

t, 07

0221


• Click on the ”write” sympol and edit the device See chapter: Connect the computer to FX3U-ENET-ADP • Enter the user interface through double-clicking on the Tosibox Lock in the software


ng_1

3053

1.do

t, 07

0221


7.3.2 Setup Ethernet port in Q03UDE with GX Works2

• Start a new project (Q03UDE) and setup the ethernet port • The default setting for “Open Setting” are 16 programming connection

• Setup the communication to the Q03UDE (ethernet port) in GX Works2


ng_1

3053

1.do

t, 07

0221


7.4 Connecting to E1000

In this example we like to programming the E1032 from a PC with E Designer. We have to setup the Tosibox Lock in “Mode B”, configure the LAN-port and E1032.


E1032


Tosibox Lock

INTERNET

Tosibox Key

LAN1-3 WAN

192.168.1.20

192.168.1.40


ng_1

3053

1.do

t, 07

0221




ng_1

3053

1.do

t, 07

0221


7.4.2 Setup Ethernet port in E1032 with E-Designer

• Start a new project (E1032) and setup the ethernet port • The IP-adress can be set in terminal with Mode-switch 1=ON at power ON.

• Setup the communication to E1032 in E-Designer


ng_1

3053

1.do

t, 07

0221


7.5 Connecting to iX T7B SoftControl

In this example we like to transfer project to iX T7B-SC from a PC with iX Developer. We have to setup the Tosibox Lock in “Mode B”, configure the LAN-port and iX T7B-SC.


iX T7B SoftControl


Tosibox Lock

INTERNET

Tosibox Key

LAN1-3 WAN

192.168.1.20

192.168.1.10


ng_1

3053

1.do

t, 07

0221




ng_1

3053

1.do

t, 07

0221


7.5.2 Setup Ethernet port in iX T7B-SC with iX developer

• Make the HMI project for iX T7B-SC and download to terminal • The IP-adress can be set in terminal at power ON (more info in manual)

• Make CODESYS project for iX T7B-SC and download to “SoftControl”


ng_1

3053

1.do

t, 07

0221


8 Application example (Mode A)

8.1 Connecting to Mitsubishi FX3U-ENET-ADP In this example we like to programming and monitoring the FX3U from a PC with GX Works2. We have to setup the Tosibox Lock in “Mode A” (default) and configure the FX3U-ENET-ADP.

Note! - Connect the Ethernet cable to “LAN3” port at Tosibox Lock. - Do not connect internet to the Tosibox Lock's WAN Port or with a 3G modem to USB Port. Doing so will automatically switch the mode of operation to Mode B! From Mode B the Tosibox Lock does not automatically return to Mode A, this needs to be done by logging in to Tosibox Lock LOCK's user interface with admin user ID. - Do not connect the controlled devices to Tosibox Lock´s LAN ports. Consider the data security! - The user of the Tosibox Key has access to all devices in the local network! - In case access rights need to be restricted, initiate MAC filtering (Industry-setting) or use Mode B.

8.1.1 Setup Tosibox Lock in Mode A Default setup for Tosibox Lock are: Mode A If the Tosibox Lock are in mode B you have to login to the Lock and change the network setting. Connect the computer to the Tosibox Lock´s “Service” Port. Type “http://laite.Tosibox” or “172.17.17.17” into the web browser. The user ID is ”admin” and the password is visible in the bottom of the Tosibox Lock. Note! The internet connection in the PC should have DHCP (Obtain an IP address automatically). • Setup the network to “DHCP client”

PC get the IP from DHCP server

PC with Tosibox Key

FX3U-ENET-ADP (left side module)

Tosibox Lock

INTERNET

Tosibox Key

LAN3

192.168.1.20 DHCP Server


ng_1

3053

1.do

t, 07

0221


8.1.2 Connect the computer to FX3U-ENET-ADP

The computer must be connected to “Internet” in another network then the Tosibox Lock! • Connect the Tosibox Key to USB port at the computer and the Tosibox software* will

start. A dialog is shown to select to use “Password”. Password is recommend. * The Tosibox software will be installed the first time you connect “Tosibox Key” to the computer.

• Enter the user interface through double-clicking on the Tosibox Lock in the software window

Network device show up under "Network devices"

In this case the connection are named to “FX3U-ENET_ADP_60”. In other case there will be the IP-adress, ex, 192.168.1.20

Now you should be able to connect the programming software (GX Works2) to FX3U. Note! Before connection with Tosibox you have to setup the PLC (FX3U) in direct connection (PC --- “SC09” --- FX3U prog.port).


ng_1

3053

1.do

t, 07

0221


8.1.3 Setup Ethernet modul FX3U-ENET-ADP in GX Works2

• Start a new project (FX3U) and setup the ethernet port

• The default setting for “Open Setting” are 4 programming connection • Setup the communication with the ethernet modul in GX Works2


ng_1

3053

1.do

t, 07

0221


9 Appendix

9.1 Tosibox Lock Service port and Web interface

9.1.1 Service port Connect the computer to the Tosibox Lock´s “Service” Port. Type “http://laite.Tosibox” or “172.17.17.17” into the web browser. The user ID is ”admin” and the password is visible in the bottom of the Tosibox Lock. Note! The internet connection in the PC should have DHCP (Obtain an IP address automatically).

9.1.2 Web interface


ng_1

3053

1.do

t, 07

0221



ng_1

3053

1.do

t, 07

0221



ng_1

3053

1.do

t, 07

0221



ng_1

3053

1.do

t, 07

0221



ng_1

3053

1.do

t, 07

0221



ng_1

3053

1.do

t, 07

0221


9.2 FAQ

How to reset Tosibox Lock to factory settings? - Can only be done by logging on to Tosibox Lock and change the settings. In the Tosibox user manual (tosibox homepage) you find: - How to erase a Tosibox Key from a Tosibox Lock? - How to handle Extra Keys and Sub Key? - How to handle a Backup Key? - How to connect a Lock with a Sub Lock? - PUK code for the Key? - Technical data for Lock? - Tosibox glossary? - Software update? - Troubleshooting?


ng_1

3053

1.do

t, 07

0221

http://www.tosibox.com/support/

Documents

TOSIBOX connection to PLC and Operator panel KI00364 … sprava/Tosibox/Startup TOSIB… · TOSIBOX connection to PLC and Operator panel KI00364 2014-06 3 Table of Contents . 1 Function