Tooling, Attachments and Accessories

Corporate Headquarters and Manufacturing Facilities

Hardinge Inc.One Hardinge Drive

Elmira, New York 14902-1507 USAwww.hardinge.com

Tooling, Attachments and Accessories

Litho in USA© Hardinge Inc., 2009

Brochure 1318APart No. C A-0009500-1318March 2009

In USA, call: 800-843-8801In Canada, call: 800-468-5946Elsewhere, call: 607-734-2281

Fax: 607-734-8819

For QUEST CHNC and Earlier Model CHNC® Turning Centers

T U R N I N G M I L L I N G G R I N D I N G W O R K H O L D I N G R O T A R Y

B R I D G E P O R TH A R D I N G E H A U S E R K E L L E N B E R G E R T R I P E T T S C H U D I N

QUEST CHNC

CHNC I CHNC II and CHNC II+ CHNC III CHNC IIISP

Hardinge Inc.Elmira, New York 14902-1507 USA

Call 800-843-8801 Monday—Friday, 8:00 am to 8:00 pm

Eastern Standard Time for FAST delivery!

© Hardinge Inc., 2009All specifications subject to change without notice.

Unless indicated otherwise, all marks indicated by ® and ™ are trademarks of Hardinge Inc.

Page 2

Diagram Model Page Key Number Description Number Number

NOTE: Additional tooling available – See pages 4 and 5

Table of Contents

3/8" & 1/2" Turret Top Plate Tooling

1 1" Extension Tool Holder With Adjustable Shim CC13 6 2 2" Extension Tool Holder With Adjustable Shim CC14 6 3 3" Extension Tool Holder With Adjustable Shim CC15 6 4 4" Extension Tool Holder With Adjustable Shim CC16 6 5 “Cut-Type” Diamond Knurling Tool C30 6 “Cut-Type” Diamond Knurling Tool CC37 6 6 Cut-Off Tool Holder* C31 7 Cut-Off Tool Holder Blades (1⁄16", 3⁄32" & 1⁄8" Blades)* P1, P2 & P3 7 7 3⁄8" Square-Shank Hardinge-Belcar Cut-Off Tool and Inserts G16 8 1⁄2" Square-Shank Hardinge-Belcar Cut-Off Tool and Inserts G18 8 1⁄2" Square-Shank Hardinge-Belcar Cut-Off Tool and Inserts G19 8 8 Left-Hand Extension Tool Holder AHC24L 9 Left-Hand Extension Tool Holder CC24L 9 9 Right-Hand Extension Tool Holder AHC25R 9 Right-Hand Extension Tool Holder CC25R 9 10 Invertible Extension Tool Holder, Right-Hand AHC30 10 Invertible Extension Tool Holder, Right-Hand CC30 10 11 Invertible Extension Tool Holder, Left-Hand AHC29 10 Invertible Extension Tool Holder, Left-Hand CC29 10

* Not used on Quest CHNC models


© Hardinge Inc., 2009All specifications subject to change without notice.Unless indicated otherwise, all marks indicated by ® and ™ are trademarks of Hardinge Inc.



Page 3

Diagram Model Page Key Number Description Number Number

Table of Contents

12 Adjustable Shim for Invertible Tool Holders CC36 10 Adjustable Shim for Invertible Tool Holders AHC36 10 13 3⁄4" Square Shank Bar Stock Puller C100 20 14 Left-Hand Drill and Shank Tool Holder (Single Bolt) CC19-5⁄8 11 Left-Hand Drill and Shank Tool Holder (Single Bolt) CC19-3⁄4 11 15 Right-Hand Drill and Shank Tool Holder (Single Bolt) CC21-5⁄8 11 Right-Hand Drill and Shank Tool Holder (Single Bolt) CC21-3⁄4 11 Right-Hand Drill and Shank Tool Holder (Single Bolt) 5⁄8" Bore AHC21 11 16 Drill and Shank Tool Holder (Two Bolt) 5⁄8" Bore C18 12 Drill and Shank Tool Holder (Two Bolt) 5⁄8" Bore CC18-5⁄8 12 Drill and Shank Tool Holder (Two Bolt) 3⁄4" Bore CC18-3⁄4 12 17 Center Adjustable Tool Holder C4 12 Center Adjustable Tool Holder CC4-5⁄8 12 18 Triple Tool Holder (5⁄8" Bore) CC34-5⁄8 13 Triple Tool Holder (5⁄8" Bore) CC33-5⁄8 13 Triple Tool Holder (3⁄4" Bore) CC33-3⁄4 13 19 Tool Holder Extension TE-5⁄8 14 Tool Holder Extension TE-3⁄4 14 20 Floating Reamer Holder T19-5⁄8 14 Floating Reamer Holder T19-3⁄4 14 21 Adjustable Tool Holder OOD-5⁄8 15 Adjustable Tool Holder OOD-3⁄4 15 22 1C Collet Holder T17-5⁄8 15 1C Collet Holder T17-3⁄4 15 22A 1C Hardinge Collets See "Tool Holder Collets & Bushings" Brochure #2351 23 1⁄2" OD Precision Bushings HDB2 16 23A 5⁄8" OD Precision Bushings HDB5 16 23B 3⁄4" OD Precision Bushings HDB6 16 24 Double-Angle Collet Tool Holder, 200-Series (31⁄2" & 51⁄2" Extension) DAH235-3⁄4 & DAH255-3⁄4 17 Double-Angle Collet Tool Holder, 300-Series (31⁄2" & 51⁄2" Extension) DAH330-1⁄2 & DAH350-1⁄2 17 Double-Angle Collet Tool Holder, 300-Series (31⁄2" & 51⁄2" Extension) DAH335-5⁄8 & DAH355-5⁄8 17 24A 200-Series Double-Angle Collets See "Tool Holder Collets & Bushings" Brochure #2351 300-Series Double-Angle Collets See "Tool Holder Collets & Bushings" Brochure #2351 25 “Crush-Type” Knurling Tool T8-5⁄8 18 “Crush-Type” Knurling Tool T8-3⁄4 18 26 “Cut-Type” Straight Knurling Tool AHC31 18 27 Revolving Stock Stop, Adjustable T20-5⁄8 19 Revolving Stock Stop, Adjustable T20-3⁄4 19 28 Revolving Stock Stop (for up to 15⁄8" Bar Work) T20-3⁄4-16 19 29 Releasing “TT” Tap Holder (Collet-Type) TT-5⁄8 21 Releasing “TT” Tap Holder (Collet-Type) TT-3⁄4 21 29A “TT” Tap Holder Collets (Size) See "Tool Holder Collets & Bushings" Brochure #2351 30 Self-Feeding Tap Holder GK11, 12, 21, 22 21 31 Square-Shank and Round-Shank Carbide and Insert Cutting Tools See Cutting Tool Catalog #1289 Tooling Package – Circle Tooling [CN 0011916CR] See Cutting Tool Catalog #1289 Tooling Package – Kennametal [CN 0011916KN] See Cutting Tool Catalog #1289 Top Plate Interchangeable 8-Station Turret Top Plate, 1⁄2" — 5 Top Plate Interchangeable 8-Station Turret Top Plate, 3⁄8" — 5 Top Plate Interchangeable 8-Station Turret Top Plate, 10 mm — 5 Top Plate Interchangeable 8-Station Turret Top Plate, 12 mm — 5 Top Plate Interchangeable Gang-Tooled Turret Top Plate, 1⁄2" — 5 Top Plate Interchangeable Gang-Tooled Turret Top Plate, 3⁄8" — 5 Miscellaneous For Additional Turret Tooling & Round Shank Tooling See Table of Contents - Page 4






Page 4

MISCELLANEOUS TURRET TOP PLATE TOOL HOLDERS AND ACCESSORIES

Photo Model Page Key Number Description Number Number

Miscellaneous Tooling

Tools for Turret Top Plates and Vertical Slide

32 Single Tool Holder C9 22 33 Double Tool Holder C10 22 34 Triple Tool Holder C20 22 35 Invertible Tool Holder (Single Block) AHC33 23 36 Invertible Tool Holder (Double Block) AHC34 23 37 Invertible Tool Holder (Triple Block) AHC35 23 38 Quadruple Tool Holder C5 24 39 Universal Tool Post C28 24 40 Boring Tool Holder C19 25 41 Boring Tool Adapter AHC22 25 42 Knurling Tool (Square Shank) — 26 43 Multiple Tool Holder for Vertical Slide* AHC6 26 44 Cut-Off Tool Holder for Vertical Slide* AHC13 27 45 P3N Cut-Off Blade for Vertical Slide* P3N 27 46 Hardinge-Belcar Cut-Off Blade* and Inserts G21 28 Miscellaneous Tools, Gages and Accessories 47 Adjustable Tool Setting Gage* N2 29 48 Tool Setting Gage Bar — 29 — Spindle Reduction Liners* — 30 — Spindle Liner Kit* — 30 — Voltage Transformers — 31 — Collet Closer Foot Switch — 31

* Not used on Quest CHNC models

44*

45*

43*

42414039

38373635343332

47*

46* 48





Page 5

Interchangeable Top Plates

Interchangeable Turret Top Plates

Hardinge® turning centers complimented with CHNC interchangeable turret top plates have consistently reduced setup time. A wide range of tooling is offered for use on the standard 8-station or optional 4-position gang-tooled turret top plates.

The turret top plates are interchangeable, allowing an operator to remove a tooled top plate from a machine and replace it with another pre-tooled top plate to reduce machine setup time. The top plate is secured to the machine by four screws.

The gang-tooled turret top plate is ideal for maximum flexibility when setting up tool configurations. It can accommodate up to six tools per side, reducing the need to index frequently and improving cycle time up to 30%, especially for small parts in the range of 1" (25.40mm) in diameter and under.

Metric top plates: Tool holders must be purchased from manufacturers other than Hardinge.

Part Tool Holders Number Used CN-0007214-A 3⁄8" square and 5⁄8" round CN-0007214-B 1⁄2" square and 3⁄4" round NC-0007214-1S 10mm square and 20mm round CC-0007214-S 12mm square and 25mm round

Part Tool Holders Number Used CN-0007214-D1 3⁄8" square and 5⁄8" round CN-0007214-D 1⁄2" square and 3⁄4" round

All tooling shown is optional.

All tooling shown is optional.8-Station Top Plates

4-Position Gang-Tool Top Plates






Page 6

A

D

E

M

N

Q

WX

Z1

C

T

L

FHARDINGEELMIRA, N.Y., U.S.A.

CC-14

The extension tool holder is generally used for turning operations, but can also be used for holding tools to back-face flanged work, or to cut off, knurl, groove, or thread a workpiece.

The extension tool holder mounts directly into a T-slot of a turret top plate and uses 3⁄8" or 1⁄2" square shank tool bits for the respective top plate. Each holder features an adjustable wedge for adjusting the tool to center. Round shank tools can be held in these holders by using the AHC22 boring tool adapter.

Extension Tool Holder with Adjustable Shim

The “cut-type” knurling tool is used to cut diamond knurls on a workpiece from 1⁄4" to 6" (6.35 to 152.40mm) in diameter.

The holder is supplied standard with two “cut-type” knurls (Part Number: ST-0010901-D). The knurls have a 3⁄4" (19.05mm) OD, a 1⁄4" (6.35mm) ID, a width of 1⁄4" (6.35mm), and a 30 diametral pitch. The knurls are adjusted by rotating the shaft to which each knurl is mounted.

The C30 and CC37 tool holders typically mount into an extension tool holder on 3⁄8" and 1⁄2" top plates, respectively.

“Cut-Type” Diamond Knurling Tool

D214"CUT-TYPE" KNURLING TOOLAHB 0010901 C-30

E

F

L

R

S

A

C

Extension Tool Holders & Cut-Type Knurling Tool

Model Part Dimensions No. Number A C E F L R S C30 AHB-0010901 Inch 1.63 2.44 .371 1.97 1.69 .380 1.22 mm 41.30 61.90 9.43 50.00 42.90 9.50 31.00 CC37 CCA-0010901 Inch 1.63 2.44 .497 2.25 1.69 .500 1.50 mm 41.30 61.90 12.62 57.20 42.90 12.70 38.10

Model Part Dimensions No. Number A C D E F L M N Q CC13 CC-0008246-01 Inch 1.50 2.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 38.10 69.90 38.10 12.70 50.80 44.50 12.70 13.10 15.10 CC14 CC-0008246-02 Inch 2.50 3.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 63.50 95.30 38.10 12.70 50.80 44.50 12.70 13.10 15.10 CC15 CC-0008246-03 Inch 3.50 4.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 88.90 120.70 38.10 12.70 50.80 44.50 12.70 13.10 15.10 CC16 CC-0008246-04 Inch 4.50 5.75 1.50 .500 2.00 1.75 .500 .520 .590 mm 114.30 146.10 38.10 12.70 50.80 44.50 12.70 13.10 15.10 T – T-Bolt W – Washer X – Nut Z1– Set Screw AH-0007241-L U-0004143 47-0001502-C 0570910





Page 7

Cut-Off Blades

The cut-off blade is for cutting or parting off material.

It mounts directly into the C31 cut-off tool holder. Each blade is made of high-speed steel and can be resharpened as needed.

Note: Not used on Quest CHNC models

Cut-Off Tool Holder

The cut-off holder mounts directly into an extension tool holder to perform cut-off operations from the turret. The cut-off holder comes supplied with a standard P1 1⁄16" (1.59mm) wide, high-speed, cut-off blade. Additional P2 and P3 blades are available in thicknesses of 3⁄32" (2.38mm) or 1⁄8" (3.18mm), respectively.

Cutting from the turret has proven to be easier for holding length dimensions and for controlling the feed rate.


Cut-Off Tool Holder & High Speed Steel Cut-Off Blades

Model Part Dimensions No. No. C F H S P1 P-0000001 Inch 4.50 .060 .477 .040 mm 114.30 1.50 12.12 .900 P2 P-0000002 Inch 4.50 .090 .477 .070 mm 114.30 2.40 12.12 1.80 P3 P-0000003 Inch 4.50 .130 .477 .100 mm 114.30 3.20 12.12 2.60

AC

F

L

M

N R

S

Y

H

Model Part Dimensions No. Number A C F H L M N R S C31 ST-0011209 Inch 1.00 1.47 1.25 .477 1.50 .130 .480 .440 .470 mm 25.40 37.30 31.80 12.12 38.10 3.20 12.20 11.10 11.90 Y – Set Screw 0100520

C

F

H

S






Page 8

Hardinge-Belcar Cut-Off Insert

The insert mounts directly into the Hardinge-Belcar cut-off tool holders. The inset configuration shapes the chips into narrow, easy-flowing coils, allowing heavier feeds and higher spindle speeds compared to conventional cut-off tools. The width of the insert and the diameter of the material determines feedrate and amount of stock removal.

Since there are no wrenches, screws, loose clamps, or springs used, the cutting forces increase the grip of the insert by locking it firmly in place. The insert is easily removed us-ing the extraction tool supplied with each cut-off tool. Inserts are purchased in packages of ten only.

Square Shank Hardinge-Belcar Cut-Off Tool

* Maximum diameter for solid workpieces. Tubing wall thickness may be half of maximum diameter.

The square shank Hardinge-Belcar cut-off tool is used to perform cut-off or grooving opera-tions.

The holder mounts into a square shank tool holder. A light grip is required to place the insert into the holder. The pressure of the first cut seats the insert and holds it tightly in the holder. The insert is removed from the holder using an extractor tool that is supplied as standard.

The insert design causes chips to roll inward and form into flowing coils during the cutting operation. This design allows faster feed rates to be used for cut-off operations.

A steady flow of coolant to the cutting edge is recommended.

Right-hand model illustrated.

Hardinge-Belcar Cut-Off Tool & Insert

Model Part Dimensions Hand Insert No. Number W H L D(Max.)* No. G16 37A-0009639-02 Inch 3⁄8" 3⁄8" 21⁄2" 11⁄8" Right 2 mm 9.52 9.52 63.50 28.58 G18 50A-0009639-02 Inch 1⁄2" 1⁄2" 3" 111⁄16" Right 1 mm 12.70 12.70 76.20 42.86 G19 50A-0009639-03 Inch 1⁄2" 1⁄2" 3" 111⁄16" Left 3 mm 12.70 12.70 76.20 42.86

W

W1

D

L

H

Model Part Dimensions Insert No. Number W1 Lead No. Hand .120" 3A-0010903-12 Inch .120 8° 1 Right mm 3.05 .093" 24A-0010903-09 Inch .093 8° 2 Right mm 2.36 .120" 3LA-0010903-12 Inch .120 8° 3 Left mm 3.05





Page 9

Right-Hand and Left-Hand Extension Tool Holders – 1⁄2" Top Plate

The extension holder is used to help balance the tool length in a turret setup, and give additional support for 1⁄2" right-hand or left-hand square shank tool bits that overhang the turret. They can be used for facing, turning, boring, chamfering, or threading operations.

The extension holder mounts directly into the machine turret top plate T-slot.

D114CC-25RRIGHT-HAND EXTENSION TOOL HOLDERPL 0011625R

AACC

EE

FF

LL

MM

NN

PP QQ TT

WWXX Z1Z1

CC-24LLeft-Hand Extension Tool HolderPL 0011625L

Left-Hand and Right-Hand Extension Tool Holders – 3⁄8" Top Plate

The extension holder is used to help balance the tool length in a turret setup and give additional support for 3⁄8" left-hand and right-hand square shank tool bits that overhang the turret. They can be used for facing, turning, boring, chamfering, or threading operations.

The extension holder mounts directly into a machine turret top plate T-slot. D1 13T OOL BLOCK ASSEMBL Y (RIGHT)AH-001 1626-R

A

C

L

Q

T

WXZ1

E

FM

N

A

C

L

Q

T

WXZ1

E

FM

N

D111 AHC14LAH 0011625 L

Extension Tool Holders

Model Part Dimensions No. Number A C E F L M N Q AHC24L AH-0011625-L Inch .910 2.00 .375 1.23 1.50 .500 .520 .590 AHC25R AH-0011626-R mm 23.00 50.80 9.53 31.40 38.10 12.70 13.10 15.10 T – T-Bolt W – Washer X – Nut Z1 – Set Screw HP-0007241 U-0004143 47-0001502-C 0570910

Model Part Dimensions No. Number A C E F L M N P Q CC24L PL-0011625-L Inch .750 2.00 .500 1.25 1.50 .530 .560 .440 .630 CC25R PL-0011625-R MM 19.10 50.80 12.70 31.80 38.10 13.50 14.30 11.10 15.90 T – T-Bolt W – Washer X – Nut Z1 – Set Screw HP-0007241 U-0004143 47-0001502-C 0570908






Page 10

Left-Hand and Right-Hand Invertible Extension Tool Holders – 3⁄8" & 1⁄2" Top Plate

The invertible tool holder is used to mount a 3⁄8" or 1⁄2" square shank tool for cutting on the rear or front of the workpiece. The holder also helps balance the tool length in a turret setup and give additional support for tools that overhang the turret.

The holder mounts into the T-slot of a machine turret top plate. If the cutting tool is to be mounted for cutting on the rear of the workpiece, the tool is inverted and shimmed to place the cutting edge of the tool on the spindle centerline. Adjustable shims AHC36 for 3⁄8" tools or CC36 for 1⁄2" tools are required and purchased seperately. (Adjustable Shims are shown below.)

Adjustable Shim For Invertible Tool Holders

The adjustable shim is used to bring a tool’s cutting edge to the height of the spindle centerline or as a spacer on top of a tool in an invertible tool holder.

The shim is placed in the invertible tool holder under the square shank tool when it is used to cut on the rear of the workpiece.

The thickness of the shim can be adjusted using the three screws built into the holder. The adjustable shim can be set very quickly to the proper thickness by the operator. D191

CC36Adjustable ShimCC 0011760

F

L

C

E

Z1

D188

AHC29

Left Hand Invertible Tool Holder

KH 001 1625 L

C CF F

A A

L L

M M

N N

T TE E

Y YZ1 Z1

AHC-29CC-29

AHC-30CC-30

Invertible Extension Holders & Adjustable Shim

Model Part Dimensions No. Number A C E F L M N AHC29 KH-0011625-L Inch .750 1.75 .375 1.23 1.94 .500 .890 AHC30 KH-0011626-R mm 19.10 44.50 9.52 31.30 49.20 12.70 22.60 CC29 CC-0011625-L Inch .750 1.75 .500 1.25 2.00 .500 1.03 CC30 CC-0011626-R mm 19.10 44.50 12.70 31.80 50.80 12.70 26.20 T – Nut Y – Cap Screw Z1 – Set Screw ST-0000374 0101028 AHC29/30 (0570912) & CC29/30 (0570910)

Model Part Dimensions No. Number C E F L CC36 CC-0011760 Inch 1.88 .50 .50 .44 MM 47.60 12.70 12.70 11.20 AHC36 KH-0011760 Inch 1.88 .38 .38 .32 MM 47.60 9.50 9.50 8.00

Z1 – Set ScrewCC36 (CH-000360) & AHC36 (KH-0010031)





Page 11

D161AHC215/8" Right Hand Drill & Shank Tool HolderAHB 0008257

A

C

E

H

L

P

Q

T

WZ XZ

1

The left-hand drill and shank tool holder is used to hold tooling or other tool holders to perform operations such as center-drilling, drilling, turning, boring, reaming, and tapping.

The holder mounts into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting. HDB bushings may be used for holding smaller shank size tools. (See page 16 for HDB bushings.)

Left-Hand Drill and Shank Tool Holders — 1⁄2" Top Plate

Right-Hand Drill and Shank Tool Holders for 3⁄8" and 1⁄2" Top Plates

The right-hand drill and shank tool holder is used to hold tooling or other tool holders to perform opera-tions such as center-drilling, drilling, turning, boring, reaming, and tapping.

The holder is mounted into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting. An HDB bushing may be used for smaller shank size tooling. (See page 16 for HDB bushings.)

D160ACC195/8" LEFT-HAND DRILL AND SHANK TOOL HOLDERPLA 0008257 62

A

C

E

F

HLM

P Q

T

W X Z 1

Left- & Right-Hand Drill and Shank Tool Holders

Model Part Dimensions No. Number A C E F H-Bore L M P Q CC19-5⁄8 PL-0008257-62 Inch .130 1.50 .500 1.50 .625 1.25 1.13 1.06 .750 mm 3.20 38.10 12.70 38.10 15.88 31.80 28.60 27.00 19.10 CC19-3⁄4 PLA-0008257-75 Inch .130 1.50 .500 1.50 .750 1.25 1.13 1.06 .750 mm 3.20 38.10 12.70 38.10 19.05 31.80 28.60 27.00 19.10 T – T-Bolt W – Washer X – Nut Z1 – Set Screw PL-0007241 FB-0006906 47-0001502-C 0570906

Model Part Dimensions No. Number A C E F H-Bore L P Q AHC21 AH-0008257 Inch .130 1.50 .375 1.50 .6253 1.00 .470 .750 mm 3.20 38.10 9.53 38.10 15.883 25.40 11.90 19.10 CC21-5⁄8 PLA-0008256-62 Inch .130 1.50 .500 1.50 .6253 1.13 .440 .750 mm 3.20 38.10 12.70 38.10 15.883 28.60 11.10 19.10 CC21-3⁄4 PLA-0008256-75 Inch .130 1.50 .500 1.50 .7503 1.13 .440 .750 mm 3.20 38.10 12.70 38.10 19.058 28.60 11.10 19.10 Model No. T – T-Bolt W – Washer X – Nut Z1 – Set Screw AHC21 HP-0007241 FB-0006906 47-0001502-C 0570906 CC21-5⁄8 PL-0007241 FB-0006906 47-0001502-C 0570906 CC21-3⁄4 PL-0007241 FB-0006906 47-0001502-C 0570906






Page 12

Center Adjustable Tool Holder

The center adjustable tool holder can be used to perform operations such as center-drilling, reaming, drilling, etc. It is one of the most accurate methods of placing a tool on the spindle centerline.

The holder provides a means for adjusting the center of a tool to its proper relationship to the spindle. After centering the tool, the adjustable portion of the holder is locked into position.

The holder mounts into the T-slot of a turret top plate and has a 5⁄8" (15.88mm) diameter bore to hold 5⁄8" round shank tools. Bushings can be used in the holder to hold tools that are 1⁄2" or less in diameter. (See page 16 for HDB bushings.)

The drill and shank tool holder is used to hold round shank tools to perform operations such as drilling, reaming, turning, boring, and threading.

The holder mounts into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting.

An HDB bushing may be used for smaller shank size tooling. (See page 16 for HDB bushings.)

Drill and Shank Tool Holder (Two-Bolt)

D152C4Center Adjustable Tool HolderST 0008249

F

L

T

A

C

E

G H

Q

WXZ1

K

D163C18Drill- & Shank-Type Tool Holder-HPC 0008249

F

E

HL

T

W X

AC

P

Q

Z1

Center Adjustable & Drill and Shank (2-Bolt) Tool Holders

Model Part Dimensions No. Number A C E F G H K L Q C4 ST-0008249 Inch 1.11 2.47 .375 2.00 .640 .6253 .980 1.11 .630 MM 28.20 62.70 9.53 50.80 16.20 15.883 25.00 28.20 15.90 CC4-5⁄8 PL-0008249 Inch 1.11 2.47 .500 2.00 .640 .6253 .980 1.23 .630 MM 28.20 62.70 12.70 50.80 16.20 15.883 25.00 31.40 15.90 T – T-Bolt W – Washer X – Nut Z1 – Set Screw HP-0007241 U-0004143 47-0001502-C 0570906

Model Part Dimensions No. Number A C E F H-Bore L P Q C18 HPC-0008249 Inch .130 1.50 .375 2.00 .6252 1.00 .440 .750 MM 3.20 38.10 9.53 50.80 15.88 25.40 11.10 19.10 CC18-5⁄8 CC-0008249-62 Inch .130 1.50 .500 2.13 .6252 1.13 .440 .750 MM 3.20 38.10 12.70 54.00 15.88 28.60 11.10 19.10 CC18-3⁄4 CC-0008249-75 Inch .130 1.50 .500 2.13 .7502 1.13 .440 .750 MM 3.20 38.10 12.70 54.00 19.06 28.60 11.10 19.10 Model No. T – T-Bolt W – Washer X – Nut Z1 – Set Screw AHC21 HP-0007241 FB-0006906 47-0001502-C 0570906 CC21-5⁄8 PL-0007241 U-00004143 47-0001502-C 0570906 CC21-3⁄4 PL-0007241 U-00004143 47-0001502-C 0570906





Page 13

Triple Tool Holder — 3⁄8" and 1⁄2" Top Plates

The triple tool holder is used to hold a maximum of three round shank tools in one tool holder to perform end-working operations such as drilling, boring, turning, reaming and tapping.

The triple tool holder is mounted into the T-slot of a turret top plate and has a lip to locate against the face of the top plate for rigidity and to prevent the holder from shifting. This holder increases tooling versatility and allows for improved production because the top plate does not have to be indexed before performing the next round shank operation.

An HDB bushing may be used for smaller shank size tooling. (See page 16 for HDB bushings.)

D164CC333/4" Triple Tool Holder for 1/2" Top PlateCC 0008257 75

A

C

E

F

G H

K

L

PQ

W X Z1

T

Triple Tool Holder

Bushings and tooling not included with this tool holder

Model Part Dimensions No. Number A C E F G H-Bore K L P Q CC34-5⁄8 CC-0008257-62 Inch .97 2.00 .375 2.88 .659 .6253 1.09 1.41 1.44 1.59 for 3⁄8" Top Plate mm 24.60 50.80 9.53 73.00 16.73 15.883 27.70 35.70 36.50 40.50 CC33-3⁄4 CC-0008257-75 Inch .97 2.00 .500 2.88 .784 .7503 1.31 1.41 1.44 1.59 for 1⁄2" Top Plate mm 24.60 50.80 12.70 73.00 19.90 19.058 33.30 35.70 36.50 40.50 CC33-5⁄8 CCA-0008257 Inch .97 2.00 .500 2.88 .659 .6253 1.31 1.41 1.44 1.59 for 1⁄2" Top Plate mm 24.60 50.80 12.70 73.00 16.73 15.883 33.30 35.70 36.50 40.50 T – T-Bolt W – Washer X – Nut Z1 – Set Screw HP-0007241 U-0004143 47-0001502-C 0570906






Page 14

The floating reamer holder is used to align the tool with the hole being reamed.

This holder mounts into a round shank tool holder and it floats freely, providing align-ment of the reamer with the hole. The holder has a 1⁄2" (12.70mm) diameter bored hole for 1⁄2" round shank tools and will accept HDB-2 bushings for holding tools with 3⁄8" and smaller shanks. (See page 16 for HDB bushings.)

D141T-19 FLOATING REAMER HOLDERST-0007967/ST 0007967-01

A BC

DF

G

H

KL

Z 1

Tool Holder Extension

The tool holder extension is used as a means to position smaller diameter drills on a common plane with other tools in the same setup, reducing tool interference.

The tool holder extension mounts directly into a round shank tool holder. It will extend round shank tools an additional 15⁄8" (41.28mm). (See page 16 for HDB bushings.)

Drill and bushing not included.

Tool Extension & Floating Reamer Holders

D117 60%TE5/8" Tool Holder ExtensionST 0011155

L

A B

C

D

G

H

K

Q

Z1

Floating Reamer Holder

Model Part Dimensions No. Number A B C D F G H K L T19-5⁄8 ST-0007967 Inch .840 1.13 1.97 .6243 1.98 .390 .5003 .660 1.00 mm 21.40 28.60 50.00 15.856 50.40 9.90 12.706 16.70 25.40 T19-3⁄4 ST-0007967-01 Inch .840 1.13 1.97 .7493 1.98 .450 .5003 .660 1.00 mm 21.40 28.60 50.00 19.031 50.40 11.50 12.706 16.70 25.40 Z1 – Set Screw 0550704

Model Part Dimensions No. Number A B C D G H K L Q TE-5⁄8 ST-0011155 Inch 1.63 1.16 2.78 .6243 .310 .6252 1.25 1.50 .310 mm 41.30 29.40 70.60 15.856 7.90 15.880 31.80 38.10 7.90 TE-3⁄4 ST-0011155-01 Inch 1.63 1.16 2.78 .7493 .310 .7502 1.25 1.50 .310 mm 41.30 29.40 70.60 19.031 7.90 19.055 31.80 38.10 7.90

Z1 – Set Screw





Page 15

Adjustable Tool Holder

D156OOD5/8" Adjustable Tool HolderOO 0007967

A BC

D

G

K

WY

F

H

L

Z1

This 1C collet-type tool holder is an accurate method of holding drills, center drills, round shank boring bars, round shank turning tools and reamers (See Brochure #2351 for collets).

The T17 holder mounts directly into a round shank tool holder. The holder is hardened and ground and holds standard 1C collets, which have a maximum capacity of 1⁄4" (6.35mm).

Turning a nut at the rear of the assembly draws the collet into the assembly, where the matching angles of the collet and the holder cause the collet to close down on the tool.

Drill and 1C collet not included.

C

D

G

MN

1C Collet Holder

Adjustable Tool Holder & 1C Collet Holder

Model Part Dimensions No. Number A B C D F G H K L OOD-5⁄8 OO-0007967 Inch .840 1.34 2.19 .6245 1.84 .375 .5002 .690 1.00 mm 21.40 34.00 55.50 15.862 46.80 9.53 12.705 17.50 25.40 OOD-3⁄4 OO-0007967-01 Inch .840 1.34 2.19 .7500 1.84 .375 .5002 .690 1.00 mm 21.40 34.00 55.50 19.050 46.80 9.53 12.705 17.50 25.40 Z1 – Set Screw 0550704

Model Part Dimensions No. Number C D G M N T17-5⁄8 37-0000102 Inch 1.82 .6243 .30 .25 .54 mm 20.80 15.856 7.60 6.40 13.70 T17-3⁄4 37-000102-01 Inch 1.82 .7493 .30 .25 .54 mm 20.80 19.031 7.60 6.40 13.70

The adjustable tool holder provides a means of adjusting center working tools such as center drills and drills to the centerline of the spindle. When the tool has been centered, the adjustable portion of the holder is locked into position.

The holder mounts into a round shank tool holder and it has a 1⁄2" (12.70mm) diameter bore to hold round shank tools. HDB-2 bushings can be used in the holder to hold tools with shanks that are 3⁄8" or less in diameter. (See next page for HDB bushings.)






Page 16

Dimensions A B Hardinge Bushing OverallStyle Part Number Figure Diameter Length Type Size Range 1⁄2"

3⁄4"HDB 2 1763-00-19 1 (12.70) (19.05) Fractional 1⁄32" to 3⁄8" inclusive by 1⁄64" increments Kit 0937-00-19 Fractional 23 Bushings from 1⁄32" to 3⁄8" by 1⁄64" Incr. 1⁄2"

3⁄4"HDB 2 1763-00-18 1 (12.70) (19.05) Decimal .141", .168", .194", .220", .255", .318", .323", .367", .381"

1⁄2" 3⁄4"

HDB 2 1763-00-17 1 (12.70) (19.05) Metric 1.0mm to 5.0mm inclusive by .2mm increments

1⁄2" 3⁄4"

HDB 2 1763-00-16 1 (12.70) (19.05) Letter A to V inclusive Kit 0937-00-16 Letter 22 Bushings from A thru V

1⁄2" 3⁄4"

HDB 2 1763-00-15 1 (12.70) (19.05) Number 1 to 67 inclusive Kit 0937-00-15 Number 67 Bushings from #1 thru #67

5⁄8" 11⁄8"HDB 5 1765-00-19 1 (15.88) (26.20) Fractional 1⁄32" to 1⁄2" inclusive by 1⁄64" increments Kit 0938-00-19 Fractional 31 Bushings from 1⁄32" to 1⁄2" by 1⁄64"

5⁄8" 11⁄8"HDB 5 1765-00-17 1 (15.88) (26.20) Metric 1.0mm to 13.0mm inclusive by .5mm increments

5⁄8" 11⁄8"HDB 5 1765-00-16 1 (15.88) (26.20) Letter A to Z inclusive Kit 0938-00-16 Letter 26 Bushings from A thru Z

5⁄8" 11⁄8"HDB 5 1765-00-15 1 (15.88) (26.20) Number 1 to 52 inclusive Kit 0938-00-15 Number 52 Bushings from #1 thru #52

3⁄4" 11⁄8"HDB 6 1881-00-19 1 (19.05) (28.58) Fractional 1⁄16" to 5⁄8" inclusive by 1⁄64" increments Kit 0939-00-19 Fractional 37 Bushings from 1⁄16" to 5⁄8" by 1⁄64"

3⁄4" 11⁄8"HDB 6 1881-00-17 1 (19.05) (28.58) Metric 2.0mm to 16.0mm inclusive by .5mm increments

3⁄4" 11⁄8"HDB 6 1881-00-16 1 (19.05) (28.58) Letter A to Z inclusive Kit 0939-00-16 Letter 26 Bushings from A thru Z

3⁄4" 11⁄8"HDB 6 1881-00-15 1 (19.05) (28.58) Number 1 to 52 inclusive Kit 0939-00-15 Number 52 Bushings from #1 thru #52

NOTE: Millimeters in parentheses.

Toolholder Bushings (HDB2, HDB5 & HDB6)

A

B

1





Page 17Double-Angle Collet Tool Holders

The Double-Angle (DA) Collet Extension Tool Holder mounts directly into a round shank tool holder. The DAH model holders will accept DA200 or DA300 collets (See Brochure #2351 for collets).

Optional qualifying collars and chuck stops are available. The collars position and lock on the holder shank to qualify the tool's position in the DAH holder. Chuck stops are positioned inside the holder body to provide a qualified locating stop for tooling and help to prevent tool “push back”.

Shown with optional collet.

Qualifying CollarDrill Stop

Double-Angle Collet Extension Tool Holders

Collet Model Shank Length Cap Cap Qualifying Collar Drill Stop Style Number Part Number A B C E Part Number Hex Part Number Part Number

DA300 DAH330 1925-00-00-000000 .500" 2.188" 3.50" .560" 1933-00-00-000000 1⁄2" 1941-00-00-000000 1939-00-00-000000

DA300 DAH350 1927-00-00-000000 .500" 4.188" 5.50" .560" 1933-00-00-000000 1⁄2" 1941-00-00-000000 1939-00-00-000000

DA300 — 7996-03-30-005000 .500" 5.500" 6.79" .560" 7991-03-30-000001 1⁄2" — 7990-03-30-000004

DA300 DAH335 1943-00-00-000000 .625" 2.188" 3.50" .680" 1951-00-00-000000 5⁄8" 1957-00-00-000000 1939-00-00-000000

DA300 DAH355 1945-00-00-000000 .625" 4.188" 5.50" .680" 1951-00-00-000000 5⁄8" 1957-00-00-000000 1939-00-00-000000

DA200 DAH255 1959-00-00-000000 .750" 1.875" 3.50" .812" 1967-00-00-000000 11⁄16" 1975-00-00-000000 1973-00-00-000000

DA200 DAH235 1961-00-00-000000 .750" 3.875" 5.50" .812" 1967-00-00-000000 11⁄16" 1975-00-00-000000 1973-00-00-000000

DA200 — 7996-03-20-007500 .750" 5.500" 7.23" .860" 7991-03-20-000001 3⁄4" — 7990-03-20-000004






Page 18

“Crush-Type” Knurling Tool

A B

C

DF

G

H

K

L

W

X

Y

45

0

0

30

3 0

Z

D213T-5/8 Crush-Type Knurling ToolSTA 0010901

“Cut-Type” Straight Knurling Tool

D212AHC315/8" “Cut-Type” Straight Knurling ToolKH 0011762

Y

B

E

C

D

"Crush- & Cut-Type" Knurling Tools

The knurling tool mounts into a round shank tool holder and comes standard with two knurls. The 64 diametrical pitch knurling wheels are mounted into swivel holders that can be set at any angle to form either diamond or straight knurls. This unit can knurl a workpiece using a cross slide motion (approaching the work perpendicularly), or a turning motion by placing the holder parallel to the workpiece and passing the workpiece between the knurls.

By making the appropriate adjustments, diameters from 5⁄32" to 1⁄2" (3.97 to 12.70mm) for the T8-5⁄8 model and to 3⁄4" (19.05mm) for the T8-3⁄4 model can be knurled. A workpiece with a diameter of 3⁄8" (9.53mm) or less can pass through the shank of the knurling tool. For stock diameters of 3⁄8" to 1⁄2" (9.53 to 12.70mm), the maximum knurling length is 7⁄8" (22.23mm).

The “cut-type” straight knurling tool is used to generate a straight knurl by cutting the metal.

The tool holder shaft mounts into a 5⁄8" round shank tool holder and comes standard with one knurl. The knurl has a 3⁄4" (19.05mm) OD and 1⁄4" (6.35mm) ID with a width of 1⁄4" (6.35mm).

Model Part Dimensions No. Number A B C D G H K L Q T8-5⁄8 STA-0010901 Inch 1.63 1.13 2.75 .6243 2.06 .390 .5002 .500 1.00 mm 41.30 28.60 69.90 15.857 52.40 9.90 12.704 12.70 25.40 T8-3⁄4 STA-0010901-75 Inch 2.44 1.49 3.93 .7493 2.80 .450 .6252 .800 1.38 mm 61.90 37.90 99.80 19.031 71.00 11.30 15.879 20.30 35.10 W – Washer X – Cutting Wheels Y – Cap Screw Z1 – Set Screw 3-0010901 T8-5⁄8 (8-0010901) & T8-3⁄4 (ST-0010901) 0100208 0550506

Model Part Dimensions No. Number B C D E AHC31 KH-0011762 Inch 2.25 2.63 .624 .500 mm 57.20 66.70 15.85 12.70 Y – Cutting Wheels ST-0010901-D





Page 19

Revolving Stock Stop

Adjustable Revolving Stock Stop

Adjustable & Revolving Stops

D146T20-3/4"-163/4" Revolving Stock StopRS 0011157 16

L D

A BC

A B

L D

D145T20A5/8" Adjustable Stock StopRSA 0011157

This revolving stock stop is designed to work with bar stock diameters up to 15⁄8" (42mm).The stop mounts into a round shank tool holder directly, or with a bushing, to position bar stock in the collet while being fed by a bar feed unit. The front portion of the stop rotates with the workpiece.

The revolving stock stop is used in a round shank tool holder to position bar stock in the collet while being fed by a bar feed unit. The front portion of the stop rotates with the workpiece.

The adjustable stop has a maximum length adjustment of 7⁄8" (22.23mm).

Model Part Dimensions No. Number Min A Max A B D L T20-5⁄8 RSA-0011157 Inch .750 1.63 1.13 .624 .810 mm 19.10 41.30 28.60 15.85 20.60 T20-3⁄4 RSA-0011157-01 Inch .750 1.63 1.13 .749 .810 mm 19.10 41.30 28.60 19.03 20.60

Model Part Dimensions No. Number A B C D L T20-3⁄4-16 RS-0011157-16 Inch 1.06 1.38 2.44 .749 1.44 mm 27.00 34.90 61.90 19.04 36.50






Page 20

Bar Stock Puller

The combination round/square shank bar stock puller is ideal for using up short pieces of bar stock or when operating floor space is limited. The puller is mounted into an invertible square shank tool holder. • Gripsstockupto15⁄8" (42mm) diameter — simple screw adjustment • Gripsround,hex,squareandoctagonstockwithoptionalcaps • Quickset-uptimeandadjustment • Gripsclosetocollet—1⁄8" (3.2mm) from face • Shortoverhangfromtheturrettopplateforminimaltoolinterference • Eliminateinventoryoffeedfingersandpullers • Self-centeringgripperadjustment • Eliminatesshockfromhydraulicfeeders

Capacity - Hex & Square Stock Model Max. Hex/Square Caps C100 19⁄32" One

Note: Spindle Reduction Liners must be used in the draw tube of the spindle when using Bar Pullers. Spindle Liner Kit – Part Number: HFSS25, HFSS30, HFSS35, HFCC42, HFCC46

Jaw Caps for Hex and Square Work

Shown with optional cap for pulling hex & square stock.

Bar Stock Puller

Puller Jaw Cap Jaw Cap Jaw Caps Model Part No. Style Required C100 1821-00-00-000007 Short Models C100 require one long jaw cap. 1821-00-00-000010 Long

Model Part Dimensions No. Number A B C D D1 E R C100 1821-00-00-000000 Inch 1.50 1.00 2.50 2.06 2.16 .750 0 to 1.50 mm 38.10 25.40 63.50 52.40 54.30 19.10 0 to 38.10

Caps Required for Hex/Square Work

BE

D C

A

D'





Page 21

Self-Feeding Tap Holder

"Collet-Type" Releasing Tap Holder

Tap and collet not included.

D199TT RELEASING TAP HOLDER ASSEMBLYSTA-0011202/STA-0011202-01

A B

C

DF

D196GK1127/32" SELF-FEEDING TAP HOLDER — THREAD ADJ.K11 0011202K

A B

C

DF L

The self-feeding tap holder provides automatic thread length control. The tap holder elimi-nates the need to match feed rate to thread pitch, minimizing tool breakage and “pulled” or “squeezed” threads.

The holder has a 5⁄8" shank diameter that allows it to be mounted into a round shank tool holder. Thread length is controlled internally with an adjusting ring in .01" (.25mm) incre-ments. A driver is used in the holder to accommodate the square of the tap shank, providing a positive drive. A collet is used to centralize and hold the tap in the holder. Tap holders are supplied standard with the necessary collets and drivers. Replacement tap collets and drivers are sold separately.

The same unit is used for left- and right-hand taps. The GK11 and GK12 models include three tap collets and four drivers. The GK21 and GK22 include six tap collets and six drivers.

The collet-type releasing tap holder is used to provide thread length control on either right- or left-hand taps by switching a lever inside the body of the tap holder.

The tap holder mounts directly into a round shank tool holder. “TT” style tap holder col-lets are used to accurately hold and center taps. To provide a positive drive for the taps, the collets have a square slot in the back to accommodate the square of the top shank and a notch in the back bearing of the collet that fits over a hardened pin in the bottom of the holder. (See Brochure #2351 for “TT” tap holder collets.)

* Collets and Drivers furnished with Tap Holder

Model Part Dimensions No. Number A B C D F TT-5⁄8 STA-0011202 Inch 2.22 1.25 3.47 .624 1.63 mm 56.40 31.80 88.10 15.85 41.30 TT-3⁄4 STA-0011202-01 Inch 2.22 1.25 3.47 .749 1.63 mm 56.40 31.80 88.10 19.03 41.30

Maximum Model Maximum Thread Length No. Tap Size Adjustment GK11 1⁄4" (6.35mm) 25⁄32" (19.84mm) GK12 1⁄4" (6.35mm) 19⁄32" (15.08mm) GK21 9⁄16" (14.29mm) 27⁄32" (21.43mm) GK22 9⁄16" (14.29mm) 19⁄32" (15.08mm)

Model Part Dimensions No. Number A B C D F L GK11 K11-0011202-K Inch 2.17 1.25 3.42 .625 1.58 .770 mm 55.10 31.80 86.90 15.88 40.10 19.60 GK12 S12-0011202-K Inch 1.89 1.25 3.14 .625 1.58 .770 mm 48.00 31.80 79.80 15.88 40.10 19.60 GK21 K21-0011202-K Inch 2.17 1.25 3.42 .625 1.58 .770 mm 55.10 31.80 86.90 15.88 40.10 19.60 GK12 S22-0011202-K Inch 1.89 1.25 3.14 .625 1.58 .770 mm 48.00 31.80 79.80 15.88 40.10 19.60

Model Tap Size Shank Collet Tap Diver Collet/Driver No. Eng. Metric Dia No. Sq. No. Part No.

GK11/12 6 1.6 .141 4-3.5 .110 2.8 1T0011831C1*/D1* GK11/12 8 4 .168 5-4 .131 3.55 1T0011831C2*/D2* GK11/12 10 4.5-5 .194 5-4 .152 4 1T0011831C2*/D2* GK11/12 12 — .220 6.5-5.5 .165 4 1T0011831C3*/D3* GK11/12 14 6 .255 6.5-5.5 .191 5 1T0011831C3*/D4* GK11/12 1⁄4" — .255 6.5-5.5 .191 5 1T0011831C3*/D4*

GK21/22 8 4 .168 5-4 .131 3.55 2T0011831C1*/D1*GK21/22 10 4.5-5 .194 5-4 .152 4 2T0011831C2*/D2*GK21/22 12 — .220 6-5 .165 4 2T0011831C2*/D2*GK21/22 14 6 .255 7-6 .191 5 2T0011831C3*/D3*GK21/22 1⁄4" 6.3 .255 7-6 .191 5 2T0011831C3*/D3*GK21/22 5⁄16" 7-8 .318 9-8 .238 6.3 2T0011831C4*/D4*GK21/22 3⁄8" 10 .381 10-9 .286 7.1 2T0011831C5*/D6*GK21/22 7⁄16" — .323 9-8 .242 6.3 2T0011831C4*/D4*GK21/22 1⁄2" 12-12.5 .367 10-9 .274 7.1 2T0011831C5*/D6*GK21/22 9⁄16" 14 .429 11-10 .322 8 2T0011831C6/D7*

Tap Collets and Drivers

"Collet-Type" Releasing & Self Feeding Tap Holders






Page 22

Single, Double & Triple Tool Holders

C20 (Triple) C10 (Double)

C9 (Single)

The single, double, and triple tool holders are used to hold 3⁄8" square shank tool bits.

The holder mounts into the T-slot of a top plate and tools are held in place with set screws. These tools are not intended to hold an inverted tool. (See next page for invertible tool holders.)

D176C10Double Tool HolderOL 0007216

A

B

C

E

R

S

U

F

L

M

N

Q

Z1

Single, Double & Triple Tool Holders

Model Part Dimensions No. Number A B C E F L M N Q R S U C9 OL-0007215 Inch .860 .340 1.00 .375 1.00 1.50 .440 .560 .280 .300 .690 .380 mm 21.80 8.70 25.40 9.53 25.40 38.10 11.10 14.30 7.10 7.50 17.50 9.50 C10 OL-0007216 Inch .860 .340 1.00 .375 1.63 1.50 .880 .560 .310 .300 .690 .380 mm 21.80 8.70 25.40 9.53 41.30 38.10 22.20 14.30 7.90 7.50 17.50 9.50 C20 HP-0008243 Inch .860 .340 1.00 .375 2.13 1.50 1.38 .560 .310 .300 .690 .380 mm 21.80 8.70 25.40 9.53 54.00 38.10 34.90 14.30 7.90 7.50 17.50 9.50 Z1 – Set Screw 0550910





Page 23

Invertible Tool Holders

The invertible tool holder is used to hold 3⁄8" square shank tool bits for cutting on the front or rear of a workpiece. One, two or three tool bits can be held, depending on the holder used.

The holders mount into the T-slot of a 3⁄8" top plate only. If the cutting tool is to be mounted for cutting on the rear of the workpiece, the tool must be inverted and shimmed in the holder using an AHC36 adjustable shim to place the cutting edge of the tool on the spindle centerline. (Shims are purchased seperately. See page 10 for adjustable shim.)

AHC 35 (Triple)

AHC 34 (Double)

AHC 33 (Single)

D190AHC34Double Block Invertible Tool HolderKH 0007216 01

C

E

F

L

M

N

P

R

SUV

Z 1

Q

Model Part Dimensions No. Number C E F L M N P Q R S U V AHC33 KH-0007215-01 Inch 1.00 .375 1.00 1.23 .340 .800 .280 .160 .300 .380 .440 .690 mm 25.40 9.53 25.40 31.40 8.70 20.30 7.10 4.00 7.50 9.50 11.10 17.50 AHC34 KH-0007216-01 Inch 1.50 .375 1.00 1.23 .340 .800 .310 .160 .300 .380 .880 .690 mm 38.10 9.53 25.40 31.40 8.70 20.30 7.90 4.00 7.50 9.50 22.20 17.50 AHC35 KH-0008243-01 Inch 2.00 .375 1.00 1.23 .340 .800 .340 .160 .300 .380 1.31 .690 mm 50.80 9.53 25.40 31.40 8.70 20.30 8.70 4.00 7.50 9.50 33.30 17.50 Z1 – Set Screw 0570908

Invertible Tool Holders






Page 24

Quadruple Tool Holder

The quadruple tool holder gives the operator greater flexibility positioning tooling on a 3⁄8" top plate

The holder is mounted into the T-slot of a turret by using two T-bolts. It can hold up to four 3⁄8" square shank tools for cutting on the front of the workpiece, or three tools cutting on the front and one inverted tool cutting on the rear of the workpiece. The tools are held in the holder with set screws.

Note: For centering inverted tools, a shim is required. The AHC36 adjustable shim shown on page 10 can be used and is purchased separately.

D177C5Quadruple Tool HolderST 0011204

A

C

E

F

L

M

N

Q S

T

U

V

YZ1

HARDINGEC-5

HARDINGEC-5

Universal Tool Post

The universal tool post mounts in the T-slots on a 3⁄8" top plate, allowing the operator to position a cutting tool to a desired angle.

The holder uses 3⁄8" square shank tool bits, and up to two tools can be held at one time. The use of shims may be necessary to center the tool.

The post can hold two tools in the following combination by repositioning the spacers: both tools right side up, both tools inverted, one tool right side up, and one tool inverted.

D192C28Universal Tool HolderST 0009644

R W

TR

R

L

X

G

F

P

Quadruple Tool Holder & Universal Tool Post

Model Part Dimensions No. Number F G L P R C28 ST-0009644 Inch 1.23 .39 1.10 .25 .368 mm 31.4 9.9 28.0 6.4 9.35 T – T-Bolt W – Washer X – Nut HP-0007241 U-0004143 47-0001502-C

Model Part Dimensions No. Number A C E F L M N Q S U V C5 ST-0011204 Inch 1.44 1.00 .375 2.91 1.81 1.44 .500 .530 .380 .560 .880 mm 36.50 25.40 9.53 73.80 46.00 36.50 12.70 13.50 9.53 14.30 22.20 T – Nut Y – Cap Screw Z1 – Set Screw ST-0000374 0101032 0550910





Page 25

Boring Tool Holder & Adapter

The boring tool adapter converts 3⁄8" and 1⁄2" square shank extension tool holders for holding 5⁄8" round shank tooling.

The adapter mounts into the slot of an extension tool holder. Two set screws hold the round shank tool securely.

HDB5 bushings can be used for holding tools that are 1⁄2" in diameter or less. (See page 16 for HDB bushings.)

Boring Tool Adapter

D167AHC22Boring Tool Adapter for 5/8" Boring BarAH 0011519

Z1

FP

ABC

E

H

LQ

Boring Tool Holder – 3⁄8" Top Plates

The boring tool holder is used to perform operations such as turning and boring.

The holder mounts into the T-slot of a turret and uses 5⁄8" round shank tooling. This holder does not have a lip and can be pivoted to obtain the proper geometry between the cutting tool and the workpiece.

HDB5 bushings can be used for holding tools that are 1⁄2" or less in diameter. (See page 16 for HDB bushings.)

D160C195/8" Boring Tool HolderHPB 0008257

C

E

F

H

L

Q

T

WX

Z1

P

Model Part Dimensions No. Number C E F H L P Q C19 HPB-0008257 Inch 1.38 .375 1.50 .625 1.00 .690 .470 mm 34.90 9.52 38.10 15.88 25.40 17.50 11.90 T - T-Bolt W - Washer X - Nut Z1 - Set Screw HP-0007241 U-0004143 47-0001502-C 0570906

Model Part Dimensions No. Number A B C E F H L P Q AHC22 AH-0011519 Inch .880 1.38 2.25 .375 1.25 .625 1.25 .630 .500 mm 22.20 34.90 57.20 9.53 31.80 15.88 31.80 15.90 12.70

Z1 – Set Screw0570906






Page 26

This knurling tool mounts directly into the tool slot of an invertible tool holder. The knurl head and shank feature a dovetail configuration which allows the head to be set to the centerline of the spindle.

To position the knurls “on center” with the spindle centerline, the head is adjusted by a simple adjustment of the socket head cap screw located in the tool’s shank. Knurl range is from 1⁄8" to 11⁄8" (3.20mm to 28.60mm).

Knurling Tool

The vertical slide multiple tool holder is used to perform operations such as forming, grooving, or chamfering. This holder will hold a maximum of three 3⁄8" square shank tools at one time.

The multiple tool holder mounts directly onto the vertical slide, with no machining necessary for instal-lation. Using the vertical slide with a multiple holder provides an additional machining station for the machine.


Multiple Tool Holder for Vertical Slide

D138AHC6Vertical Slide Multiple Tool HolderAH 0011339 S

F

L

R

S

U

CM

NPQ

Z1

Knurling Tool & Multiple Tool Holder

Model Part Dimensions No. Number A B C D F KO75 1827-00-00-000000 Inch 1.50 .750 2.50 2.06 .656 mm 38.10 19.05 63.50 52.40 16.66

Model Part Dimensions No. Number C F L M N P Q R S U AHC6 AH-0011339-S Inch 1.75 20.6 3.38 1.31 .440 1.13 .250 1.75 1.06 1.00 mm 44.50 52.40 85.70 33.30 11.10 28.60 6.40 44.50 27.00 25.40

Z1 – Set Screw0570610





Page 27Cut-Off Tool Holder & Blade

Cut-Off Tool Holder for Vertical Slide

The vertical slide cut-off holder is used as an alternative means of cutting off in order to free a turret station to perform forming and turning operations.

The holder mounts directly into the machine’s vertical slide without additional machining for installation. The cut-off holder is supplied with one P3N 3⁄32" (2.38mm) wide, high-speed, cut-off blade, shown below. The Hardinge®-Belcar carbide insert cut-off blade, shown on the next page, can be used in place of the blade supplied.

The cut-off blade is locked in the holder using two eccentric screws. The feed and length of travel are operated by hydraulics and can be adjusted by the operator. Travel of the vertical slide is controlled by using a stop screw.


Model Part Dimensions No. Number A B C F M N P Q R S U V AHC13 AH-0009724-01 Inch .590 .310 4.19 2.00 2.31 1.66 .340 1.94 1.44 .630 .810 1.94 mm 15.00 7.90 106.40 50.80 58.70 42.10 8.70 49.20 36.50 15.90 20.60 49.20 W – Washer Y– Bolt Z1 – Set Screw AD-0001067 VD-0011903 0100510

A

WY

BC

F

M

N

P

Q

R

S

UV

Z 1

B

Cut-Off Blade

The cut-off blade is for cutting or parting off material.

It mounts directly into the cut-off tool holder for the vertical slide. The blade is made of high-speed steel and can be resharpened as needed.


C

F

H

S Model Part Dimensions No. Number C F L S P3N VC-0009639 Inch 5.00 .090 .675 .080 mm 127.00 2.40 17.15 2.00






Page 28

Hardinge-Belcar Cut-Off Insert

The insert mounts directly into the Hardinge-Belcar G21 blade shown above. The inset configuration shapes the chips into narrow, easy-flowing coils, allowing heavier feeds and higher spindle speeds compared to conventional cut-off tools. The width of the insert and the diameter of the material determines feedrate and amount of stock removal.

Since there are no wrenches, screws, loose clamps, or springs used, the cutting forces increase the grip of the insert by locking it firmly in place. The insert is easily removed using the extraction tool supplied with each cut-off tool. Inserts are available in pack-ages of ten.

Cut-Off Blade & Insert

The Hardinge-Belcar adjustable blade is used to perform cut-off operations.

It is an insert cut-off tool that mounts directly into a cut-off tool holder. The blade uses a general purpose grade carbide insert. The insert is mounted into the cut-off tool using a press fit. It is removed by using the extractor tool that is supplied with the blade.

The insert design causes chips to roll inward and form into flowing coils during cut-off operations. The design also allows faster feed rates to be used. See below for inserts.

A steady flow of coolant to the cutting edge is recommended.


Hardinge-Belcar Cut-Off Blade

H

L

H1

W

D

W1

* Maximum diameter for solid workpieces. Tubing wall thickness may be half of maximum diameter.

Model Part Dimensions Insert No. Number W H=H1 L D(Max.)* No. G21 68A-0009639-03 Inch .088 .6875 4.375 2.375 1,2 or 3 mm 22.35 17.46 111.13 60.30

Model Part Dimensions Insert No. Number W1 Lead No. Hand .120" 3A-0010903-12 Inch .120 8° 1 Right mm 3.05 .093" 24A-0010903-09 Inch .093 8° 2 Right mm 2.36 .120" 3LA-0010903-12 Inch .120 8° 3 Left mm 3.05





Page 29

Adjustable Tool Setting Gage

The tool setting gage is used to set cutting tools to the height of the spindle centerline quickly and accurately for longer tool life, easier cutting, better surface finishes and closer tolerances. The gage is hardened and ground to maintain accuracy and can be used for setting tools cutting on the front or rear of the workpiece.

The gage has two ground surfaces "A" and "B". Surface "A" is for setting tools to cut on the front of the workpiece, surface "B" is for setting tools to cut on the rear of the workpiece. The top section swivels to cover and protect the ground gage surfaces.

The gage can be set to the centerline of the spindle using the tool setting gage bar shown above which is held in a 1.000" or a 20mm round collet in the machine spindle.

The gage can also be set using an indicator stand positioned on the top of the bed plate. A ground plug is held in a collet with the 1" travel indicator set to the top of the plug. The gage is then set to one-half the diameter of the ground plug.


Adjustable Tool Setting Gage (Model N2) – Part Number: NC-0011159

Tool Setting Bar & Gage

Tool Setting Gage Bar

The tool setting gage bar is used to align round shank tool holders with the spindle centerline. The hardened and ground bar allows both 5/8" and 3/4" diameter round shank holders to be centered. The metric tool setting gage bar has 16mm, 19mm, 20mm diameters. The flat section on the end of the bar is used to set the adjustable tool setting gages.

Tool Setting Gage, English – Part Number: HPA-0010027Tool Setting Gage, Metric – Part Number: HPA-0010027-M

A

B






Page 30

Spindle Liner Kit

Spindle liner kits are available for Hardinge® 16C-spindle machines when using bar stock pullers or bar feed systems. The use of a spindle liner kit is required for bar pulling and bar feeding applications to reduce spindle vibration and prevent possible damage to the spindle ID, resulting from bar whip. Additionally, the use of spindle liners enhance the gripping capability of spindle tooling and help ensure uniform surface finishing and close-tolerance machining.


Spindle Reduction Liners & Liner Kit

Spindle Reduction Liners

Spindle Reduction liners are required when using Bar Pullers on machines with a 16C spindle. The liners can greatly reduce spindle vibration for better finishes and tolerances on machined parts by reducing the spindle size to more closely match the bar stock size. In addition to protecting the spindle ID from possible bar whip, Hardinge spindle liners enhance the gripping capability of spindle tooling and help ensure uniform surface finishing and close-tolerance machining. Two O-rings on the sleeve of each reduction liner provide rotational stability.


HFCC46 model illustrated.

HFSS25 model illustrated.

D273HFCC46SPINDLE REDUCTION LINERS FOR 16C SPINDLE MACHINESCC 0012017 46

W

A

C

D G

U V

D272HFSS25SPINDLE REDUCTION LINERS FOR 16C SPINDLE MACHINES16001201725

BA

C

D

GV

L

Model Part Dimensions Round Bar Stock No. Number A B C D G L U V Liner ID Capacity Range HFSS25 16-0012017-25 Inch 17.88 3.00 19.07 1.67 .780 2.00 — .880 .782 .125 to .750 mm 454.00 76.20 484.50 42.40 19.80 50.80 — 22.40 19.90 3.20 to 19.10 HFSS30 16-0012017-30 Inch 17.88 3.00 19.07 1.67 .940 2.00 — .880 .938 .766 to .906 mm 454.00 76.20 484.50 42.40 23.80 50.80 — 22.40 23.80 19.50 to 23.00 HFSS35 16-0012017-35 Inch 17.88 3.00 19.07 1.67 1.09 2.00 — .880 1.09 .922 to 1.063 mm 454.00 76.20 484.50 42.40 27.80 50.80 — 22.40 27.80 23.40 to 27.00 HFCC42 CC-0012017-42 Inch 25.59 — 25.71 1.67 1.31 — 1.00 1.75 1.31 1.078 to 1.281 mm 650.00 — 653.00 42.40 33.40 — 25.40 44.50 33.40 27.40 to 32.50 HFCC46 CC-0012017-46 Inch 25.59 — 25.71 1.67 1.44 — 1.00 1.75 1.43 1.297 to 1.406 mm 650.00 — 653.00 42.40 36.50 — 25.40 44.50 36.50 32.90 to 35.70

Kit Bushing Round Bar Part No. Part No. Stock Range CN-0012017-S QS-0012017 .120" to 1.65" (3mm to 42mm)

WORLDWIDE MANUFACTUREROF HIGH-PRECISION MACHINE TOOLS

AND WORKHOLDING/INDUSTRIAL PRODUCTS

www.hardinge.com

Documents

Tooling, Attachments and Accessories