VS862 - 2 - 151107 1 ≤ V2.4 SOFTWARE

MODEL: VS862SOFTWARE ≤ V2.4

Table of Contents

Section No: yy Page No:1. Safety Precautions and Warnings 2yy2. Product Information 3yy2.1. Description 3yy2.2.Specifications 4yy2.3.AccessoriesIncluded 4yy2.4.NavigationCharacters 4yy2.5. Keyboard 5yy2.6. Power 5yy2.7. Product Setup 5yy2.8.VehicleCoverage 8yy3. Operating Instructions 9yy3.1. VW/AUDI Diagnostics 9yy3.2. OBDII/EOBD Diagnostics 15yy3.3.OilService 19yy

Instructions For: VAG CODE READER AND

RESET TOOL EOBD & GENERIC

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.

IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.

VS862 - 2 - 151107 2 ≤ V2.4 SOFTWARE

1. SAFETY INSTRUCTIONS

WARNING!EnsurethatHealthandSafety,localauthorityandgeneral Workshoppracticeregulationsarestrictlyadheredto. DO NOTusetheunitifit,oranyattachment,isdamaged. Maintaintheunitingoodandcleanconditionforbestandsafest performance. Ifrequired,ensurethatthevehicletobeworkedonisadequatelysupported withaxlestandsorrampsandischocked. PuttransmissioninPARK(forautomatictransmission)orNEUTRAL(for manualtransmission)andmakesuretheparkingbrakeisengaged. Wearapprovedeyeprotection.Afullrangeofpersonalsafetyequipmentis availablefromyourSealeydealer. Wearsuitableclothingtoavoidsnagging.Donotwearjewelleryandtie backlonghair. WARNING!Useextremecautionwhenworkingaroundtheignition coil,distributorcap,ignitionwiresandsparkplugs.Thesecomponents createhazardousvoltageswhentheengineisrunning. DO NOTconnectordisconnectanytestequipmentwithignitiononor engine running. Keepafireextinguishersuitableforgasoline/chemical/electricalfires nearby. Accountforalltoolsandpartsbeingusedanddonotleavethemonornear theengine. Keepcodereaderdry,cleanandfreefromoil,waterandgrease.Useamild detergentonacleanclothtocleantheoutsideofthetool. Operatethevehicleinawell-ventilatedworkarea;exhaustgasesare poisonous. IMPORTANT:Alwaysrefertothevehiclemanufacturer’sservice instructionstoestablishthecurrentprocedureanddata.Theseinstructionsare providedasaguide only. WARNING! The warnings, cautions and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the operator.

VS862 - 2 - 151107 3 ≤ V2.4 SOFTWARE

2. PRODUCT INFORMATION

2.1 DescriptionLCD DISPLAY1 --Indicatestestresults.Backlit,128x64pixeldisplaywithcontrastadjustment.Y BUTTON2 --Confirms a selection (or action) from amenu.When aDTC’sdefinitioncoversmorethanonescreen,itisusedtomovedowntothenextscreenforadditionaldata.

IMPORTANT - We are constantly improving the operating of this tool to work with other VAG vehicles. In the event that your VS862 will not connect to a vehicle or it appears not to communicate with a specific vehicle type; we recommend that you download the latest operating software and DTC library from the Sealey website (www.sealey.co.uk) and update your VS862 with the latest code and retry your problem vehicle.

VS862 - 2 - 151107 4 ≤ V2.4 SOFTWARE

3) N BUTTON--Cancelsaselection(oraction)fromamenuorreturnstothemenu.Itisalsousedtosetuptheunitwhenbeingpressedandheldforat least 3 seconds.

4) UP SCROLL BUTTON --Moves up throughmenu and submenuitems inmenumode.Whenmore thanoneDTCis retrieved,movesupthroughthecurrentscreentothepreviousscreensforadditionalDTCsanddefinitions.

5) DOWN SCROLL BUTTON -- Moves down through menu andsubmenu items inmenumode.Whenmore than oneDTC is retrieved,movesdownthroughthecurrentscreentothenextscreensforadditionalDTCsanddefinitions.

6) OBD II CONNECTOR -- Connectsthescantooltothevehicle’sDataLinkConnector(DLC).

2.2 SpecificationsDisplay:1) Backlit,128x64pixeldisplaywithcontrastadjustment.Operating Temperature:2) 0to50°C(32to122F°).Storage Temperature:3) -20to70°C(-4to158F°).External Power:4) 8.0to15.0Voltsprovidedviavehiclebattery.Dimensions: 5)

Length Width Height 178mm(7.00”)95mm(3.75”)34mm(1.35”)

NW:6) 0.70kg(1.54lb),GW: 1.0kg(2.20lb)

Audi,Seat,Skoda,VW;Beetle,Golf,GTI,Jetta,Passat,Touareg,Touran.

2.3 Accessories Included

User’s Manual1) --Instructionsontooloperations.OBD2 cable2) --Providespowertotoolandcommunicatesbetweentoolandvehicle.Serial Cable3) --Usedtoupgradethescantool.Carry Case4) --Anyloncasetostorethescantoolwhennotinuse.

2.4 Navigation CharactersCharactersusedtohelpnavigatethescantoolare:

“►”1) --Indicatescurrentselection.“↓”--Aflashingdownarrowindicatesadditionalinformationisavailable2) onthenextscreen.

VS862 - 2 - 151107 5 ≤ V2.4 SOFTWARE

“↑”--Aflashinguparrowindicatesadditionalinformationisavailableon3) thepreviousscreen.“pd”--IdentifiesapendingDTCwhenviewingDTCs.4)

2.5 KeyboardDo not usesolventssuchasalcoholareallowedtocleanthekeypadordisplay.Use amild nonabrasive detergent and a soft cotton cloth. Do not soak thekeypad,asthekeypadisnotwaterproof.

2.6 Power

The external power of the scan tool is provided via the vehicle Data LinkConnector(DLC).Justfollowthestepsbelowtoturnonthescantool:

ConnecttheOBDIICabletoscantool.1)

FindDLConvehicle(refertoproprietaryhandbook).2)

3) A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD2 cable.PlugOBDIICabletothevehicle’sDLC.4)

2.7 Product SetupThe scan tool allows you to make the following adjustments and settings:

Contrast Adjustment:1) AdjuststhecontrastoftheLCDdisplay.Display Test:2) TeststheLCDdisplay.Keyboard Test:3) Teststhekeyboard.

To enter the setup menu modeFrom the keyboard: 1) Pressandhold theN button for at least 3 seconds untiltheSystem Setupmenushowsup.Followtheinstructionstomakeadjustmentsandsettingsasdescribedinthefollowingsetupoptions.

System Setup►1)Contrast2)DisplayTest3)KeyboardTest

VS862 - 2 - 151107 6 ≤ V2.4 SOFTWARE

From the Main Menu: 2) Use the UP/DOWN Scroll Buttons to select System SetupandthenpresstheYbutton.Followtheinstructionstomakeadjustmentsandsettingsasdescribedinthefollowingsetupoptions.

Contrast Adjustment

Fromthe1) System Setup menu,usetheUP/DOWN scroll buttons to select Contrast,andpresstheY button.

Fromthe2) Contrastmenu,usetheUP/DOWN scroll buttons to increase or decreasethecontrast.

Pressthe3) Ybuttontosaveyourselectionandreturntopreviousmenu.Pressthe4) Nbuttontoreturntopreviousmenus.

Main Menu

1) VW/AUDI2) OBDII/EOBD3)OilService

►4)SystemSetup

System Setup

►1)Contrast2)DisplayTest3)KeyboardTest

Contrast

Contrast（45%）

Use or tochange

VS862 - 2 - 151107 7 ≤ V2.4 SOFTWARE

Display Test The Display Test is used to check the LCD display.

Fromthe1) System Setupmenu,usetheUP/DOWN scroll buttons to select Display Test andpresstheY button.

Pressthe2) Ybuttonagaintostarttest.Lookformissingspotsinthesolidblackcharacters.

Whencompleted,pressthe3) N button to return.

Keyboard TestThe Keyboard Test is used to verify that the keys are functioning properly.

Usethe1) UP/DOWN scroll buttons to select Keyboard Test from System Setupmenu,andthenpressY button.

System Setup

1)Contrast►2)DisplayTest3)KeyboardTest

DisplayTestPress [Y] to test.Lookformissingspotsincharacters.

Press<N>toreturn.

VS862 - 2 - 151107 8 ≤ V2.4 SOFTWARE

Pressanykeytostarttest.Whenyoupressakey,thekeynameshouldbe2) observedonthedisplay.Ifthenamedoesnotshowup,thenthekeyisnotfunctioning properly.

Double press 3) Ntoreturntothepreviousmenu.

2.8 Vehicle CoverageTheVS862VW/AUDICodeScannerisspeciallydesignedtoworkwithmostVolkswagen and Audis sold worldwide of 1990 or newer models. If a VW/AUDI has a 16-pin “OBD-II style” Data Link Connector (DTC), the codereaderwillwork.Ifithasanold-style2x2DataLinkConnector(DTC),thenitdependsonwhetherthereare4or3wiresconnectingtothepins.

Ifthereare4wires,eachconnectingapin,thenitwillwork.Ifthereareonly3wires,leavingonepindisconnected,thenitwillnotwork.ForVW/AUDIwithold-style2x2DataLinkConnector(DTC),youneedtohavea2x2cablingadapterwhichisnotincludedinthisproductpackage.Order No. VS8X01

System Setup

1)Contrast2)DisplayTest

►3)KeyboardTest

KeyboardTest

Press any key toStart test todisplay name.

Key:

Double[N]toReturn

VS862 - 2 - 151107 9 ≤ V2.4 SOFTWARE

3. OPERATING INSTRUCTIONS

3.1 VW/AUDI Diagnostics

Reading CodesCAUTION: Do not connect or disconnect any test equipment with ignition on or engine running.

Turntheignitionoff.1) Locatethevehicle’s16-pinDataLinkConnector(DLC).2) PlugtheOBDIIconnectortothevehicle’sDLC.3) Turntheignitionon.Butdonotstarttheengine.4) Pressthe5) Ybutton.TheMain Menuwillbeobservedonthedisplay.Usethe6) UP/DOWN scroll buttons to select VW/AUDIfromthemenuandpresstheY button.

Use the7) UP/DOWN scrollbuttons to select the system from theSelect SystemmenuandpresstheY button.

Main Menu

►1)VW/AUDI2) OBDII/EOBD3)OilService4)SystemSetup

VS862 - 2 - 151107 10 ≤ V2.4 SOFTWARE

If the scan tool fails to communicate with the selected vehicle’s ECU y(Electronic Control Unit), a “LINK ERROR!” message shows up on the display. VerifythattheignitionisON;y

Checkifthescantool’sOBDIIconnectorissecurelyconnectedtotheyvehicle’sDLC;Verifythatthemoduleissupported;y

Turntheignitionoffandwaitforabout10seconds.Turntheignitionybacktoonandrepeattheprocedurefromstep5.If the “LINK ERROR” message does not go away, then there might ybe problems for the scan tool communicating with the module being tested. The most common cause is that the scanned module is not supported on the vehicle.

The numbers (01, 02, 15, 03, 08, etc) in front of the system names refer yto the physical addresses assigned to the systems, not the sequence of the systems to be arranged.

Select 8) Read Codes from the Select Function menu and press the Y button.

Select System►01)Engine02)AutoTrans15) Airbags03) ABS Brakes08)AutoHVAC09)Cent.Elect.

IMPORTANT - We are constantly improving the operating of this tool to work with other VAG vehicles. In the event that your VS862 will not connect to a vehicle or it appears not to communicate with a specific vehicle type; we recommend that you download the latest operating software and DTC library from the Sealey website (www.sealey.co.uk) and update your VS862 with the latest code and retry your problem vehicle.

VS862 - 2 - 151107 11 ≤ V2.4 SOFTWARE

If there are no Diagnostic Trouble Codes present, the display willyindicate,“NO CODES ARE STORED IN THE MODULE!”IfthereareanyDiagnosticTroubleCodespresent,theDTCnumber y

anditsdefinitionwillshowontheLCDdisplay.Thesub-code,thecommunicationprotocol,thesequenceoftheDTC y

currentlybeingobservedandthetotalnumberofcodesdetectedwillbeobservedontheupperrighthandcornerofthedisplay.WhenaDTC’sdefinitioncoversmorethanonedisplayscreen,usethe y

Ybutton,asnecessary,toviewanyadditionalinformation.IftheDTCdefinitionisnotavailable,anadvisorymessagepromptingyyou to refer to the vehicle servicemanualwill be observed on thedisplay. IfmorethanoneDTCisfound,usethey UP/DOWNscrollbuttons,asnecessary,untilallthecodeshavebeenshownup.

SelectFunction

►1)ReadCodes2)EraseCodes3)ECUInformation4)ReadinessTest

16627--10001/10CANBUS

↓SolenoidValve(A)ForBoostPressureControl(N75):Malfunction:P0243

VS862 - 2 - 151107 12 ≤ V2.4 SOFTWARE

Erasing CodesCAUTION: Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle’s on-board computer, but also “Freeze Frame” data and manufacturer specific enhanced data. Further, the I/M Readiness Monitor Status for all vehicle monitors is reset to Fail status. Do not erase the codes before the system has been checked completely by a technician.

If youdecide to erase theDTCs, use the1) UP/DOWN scroll buttons to select Erase Codes from Select Function menuandpresstheY button.

Ifthescantoolisnotconnectedornocommunicationisestablishedywith the vehicle yet, then refer toReading Codes from 1 to 7 at Paragraph3.1.

Awarningmessagecomesupaskingforyourconfirmation.2)

Ifyoudonotwanttoproceedwitherasingthecodes,pressthe3) N button to exit.Amessageof“command cancelled”willshowup.Ifyoudowishtoproceedtoerasethecodes,thenpressthe4) Y button.

SelectFunction

1)ReadCodes►2)EraseCodes3)ECUInformation4)ReadinessTest

EraseCodes

EraseTroubleCodes!Are you sure?

<YES>NO

VS862 - 2 - 151107 13 ≤ V2.4 SOFTWARE

Ifthecodesareclearedsuccessfully,an“5) ERASE DONE!”confirmationmessagewillshowonthedisplay.Pressanybuttontoreturn tothepreviousmenus.Ifthecodesarenotcleared,thenan“6) ERASE FAILURE!” message will appear.PresstheN buttontoreturntopreviousmenus.

Viewing ECU InformationToview1) ECU Information,usetheUP/DOWN scroll buttons to select ECU Information from Select FunctionmenuandpresstheY button.

Ifthescantoolisnotconnectedornocommunicationisestablished y

with the vehicle yet, then refer toReading Codes from 1 to 7 at Paragraph3.1.

IfthereisnoECUInformationavailable,awarningmessageshowsyonthedisplay.

Pressthe2) Nbuttontoreturntopreviousmenus.

SelectFunction

1)ReadCode2)EraseCode

►3)ECUInformation4)ReadinessTest

ECUInformation

VAGNo.:06A906032TFComponent:Bosch1.815VT 0020Coding:0008570Imp:0000WSC:000078

VS862 - 2 - 151107 14 ≤ V2.4 SOFTWARE

Readiness TestImportant: The Readiness Test function is used to check the operations of the Emission System on OBD2/EOBD compliant vehicles. It is an excellent function to use prior to having a vehicle inspected for compliance to an emissions program.

“Pass” -- Indicates that a particular monitor being checked has completed yits diagnostic testing.“Fail” -- Indicates that a particular monitor being checked has not ycompleted its diagnostic testing or the monitor is not supported on that vehicle.Usethe1) UP/DOWN scroll buttons to select Readiness Test from Select FunctionmenuandpresstheY button.

Ifthescantoolisnotconnectedyet,thenrefertoy Reading Codes from 1to7atParagraph3.1.

Usethe2) UP/DOWNscrollbuttons,asnecessary,toviewthestatusofthefollowing monitors:

EGRSys.--EGRSystemMonitor.yO2Sensor(s)--O2SensorsMonitor.yCatalyst--CatalystMonitor.yEVAPSys.--EvaporativeSystemMonitor.yHeatedO2--O2SensorHeaterMonitor.ySecAirInject--SecondaryAirMonitor.yA/C--A/CsystemMonitor.yCatalyticConv.--CatalyticConvertorMonitor.y

SelectFunction

1)ReadCode2)EraseCode3)ECUInformation

►4)ReadinessTest

VS862 - 2 - 151107 15 ≤ V2.4 SOFTWARE

Pressthe3) Nbuttontoreturntopreviousmenus.

3.2 OBDII/EOBD Diagnostics

Reading CodesCAUTION: Don’t connect or disconnect any test equipment with ignition on or engine running.

Turntheignitionoff.1) Locatethevehicle’s16-pinDataLinkConnector(DLC).2) PlugtheOBDIIconnectortothevehicle’sDLC.3) Turntheignitionon.Butdonotstarttheengine.4) Pressthe5) Ybutton.TheMain Menuwillbeobservedonthedisplay.Use the6) UP/DOWN scroll buttons to select OBDII/EOBD from themenu.

Press the7) Y button.A sequenceofmessages showing theOBDII/EOBDprotocols will be observed on the display until the vehicle protocol isdetected.

ReadinessTest ↓

EGRSys.PassHeatedO2Pass O2 Sensor(s) PassA/CPassSec.AirInjectPassEVAPSys.Fail

Main Menu

1) VW/AUDI►2)OBDII/EOBD3)OilService4)SystemSetup

VS862 - 2 - 151107 16 ≤ V2.4 SOFTWARE

If the scan tool fails to communicate with the vehicle’s ECU (Engine Control Unit), a “LINK ERROR!” message shows up on the display.

VerifythattheignitionisON;y

Checkifthescantool’sOBDIIconnectorissecurelyconnectedtotheyvehicle’sDLC;VerifythatthevehicleisOBDII/EOBDcompliant;y

Turntheignitionoffandwaitforabout10seconds.Turntheignitionybacktoonandrepeattheprocedurefromstep5.If the “LINK ERROR” message does not go away, then there might be yproblems with the scan tool communicating with the vehicle. Contact your local distributor for assistance.

After thevehicleprotocol isdisplayedonthescreen,pressanykeyorwait8) about2secondsfortheOBDII/EOBD DIAG. menu to come up.Usethe9) UP/DOWN scroll buttons to select Read CodesfromthemenuandpresstheY button.

If there are no Diagnostic Trouble Codes present, the display willyindicate,“NO CODES ARE STORED IN THE MODULE!”IfthereareanyDiagnosticTroubleCodespresent,theFaultCodesandyPendingCodeswillbereportedonthedisplay.

OBDII/EOBDDIAG.

►1)ReadCodes2)EraseCodes

VS862 - 2 - 151107 17 ≤ V2.4 SOFTWARE

TheDTC numberwill appear on the upper left hand corner and its y

definitionwillshowonthebodyofscreen.The type of code (Generic or Manufacturer specific), the vehicle y

protocol,thesequenceoftheDTCcurrentlybeingobserved,thetotalnumberofcodesdetectedandthemoduleIDwillbeobservedontheupperrighthandcornerofthedisplay.If the code being displayed is a pending code, the y Pd icon will be observednext to theDTCnumberon theupper righthandcornerofthedisplay.WhenaDTC’sdefinitioncoversmorethanonedisplayscreen,usethe y

Ybutton,asnecessary,toviewanyadditionalinformation.If theretrievedDTCscontainanymanufacturerspecificorenhancedycodes, youwill be prompted to refer to theCDDTC library or thevehicleservicemanualtoviewtheDTCdefinitions.

If more than one DTC is found, use the10) UP/DOWN scroll buttons, asnecessary,untilallthecodeshavebeenshownup.

Erasing CodesIf you decide to erase the DTCs, use the1) UP/DOWN scroll buttons to select Erase CodesfromtheOBDII/EOBD DIAG.menuandpresstheY button.

P0118 Pd 06/06ISO9141 $09

↓PressureControlSolenoidAControlCircuitLow

OBDII/EOBDDIAG.

►1)ReadCodes2)EraseCodes

VS862 - 2 - 151107 18 ≤ V2.4 SOFTWARE

If thescan tool isnotconnectedornocommunication isestablishedywith the vehicle yet, then refer toReading Codes from 1 to 8 at Paragraph3.2.

2) Awarningmessagecomesupaskingforyourconfirmation.

3) Ifyoudonotwanttoproceedwitherasingthecodes,presstheN button to exit. A message of “command cancelled”willshowup.

Ifyoudowishtoproceedtoerasethecodes,thenpressthe4) Y button. If thecodesareclearedsuccessfully,an“5) ERASE DONE!”confirmationwillshowonthedisplay.Pressanybuttontoreturn topreviousmenus.Ifthecodesarenotcleared,thenan“6) ERASE FAILURE!” message will appear.PresstheN buttontoreturntoprevious menus.

EraseCodes

EraseTroubleCodes!Are you sure?

<YES>NO

VS862 - 2 - 151107 19 ≤ V2.4 SOFTWARE

3.3 Oil ServiceTurntheignitionoff.1) Locatethevehicle’s16-pinDataLinkConnector(DLC).2) PlugtheOBDIIconnectortothevehicle’sDLC.3) Turntheignitionon.Butdonotstarttheengine.4) Pressthe5) Ybutton.TheMain Menuwillbeobservedonthedisplay.Use 6) UP/DOWN scroll button to select Oil Service from themenu, andpresstheY button.

Use 7) UP/DOWNscrollbuttontoselectvehiclemaker,andpressY button.

Use 8) UP/DOWNscrollbuttontoselectavehicle,andpressY button to confirm.

Main Menu

1) VW/AUDI2) OBDII/EOBD

►3)OilService4)SystemSetup

OilService

1) Auto Detect2) Audi

►3)VW4)Seat5) Skoda

VS862 - 2 - 151107 20 ≤ V2.4 SOFTWARE

Ifyourvehicleisnotlistedonthescreen,usey UP/DOWN scroll button to select Others fromthemenu,andpressYbuttontoconfirm.

Resetting Longlife Oil ServiceUse 1) UP/DOWN scroll button to select Longlife Oilfromthemenu,andpress Y button.

Use 2) UP/DOWN scroll button to select Service Reset from Longlife Oil menu,andpressY button.

Press any key to return to3) Longlife Oil menu.

SelectVehicle ↓

01)Golf302)Golf4

►03)NewBeetle04)Passat05) Passat B506) Passat 97

OilService ►1)LonglifeOil2)NonLonglifeOil3)SetInsp.Interval

LonglifeOil ►1)ServiceReset2)SetOilType3)ViewOilType

VS862 - 2 - 151107 21 ≤ V2.4 SOFTWARE

Tosetoiltype,use4) UP/DOWN scroll button to select Set Oil Type from Longlife Oilmenu,andpressY button.

Use 5) UP/DOWNscrollbuttontoselectanoiltypeaccordingtothatofyourvehicle.

Press any key to return to 6) Longlife Oil menu.

Toviewoil type,use7) UP/DOWN scroll button to select View Oil Type from Longlife Oilmenu,andpressY button.

ServiceReset RESETOK!

Press any key to con.

SetOilType ►1)Diesel2)V6Tdi 3) Petrol4)NonLonglifeOil

OilTypeReset RESETOK!

Press any key to con.

VS862 - 2 - 151107 22 ≤ V2.4 SOFTWARE

View oil type on screen and press any key to return to 8) Lifelong Oil menu.

Resetting Non Longlife Oil ServiceToresetnonlonglifeoilservice,use1) UP/DOWN scroll button to select Non Longlife OilfromtheOil Servicemenu,andpressY button.

Use 2) UP/DOWNscrollbuttontoselectfromtheService Reset Non Longlife Oilmenu,andpressY button.

LonglifeOil 1)ServiceReset2)SetOilType►3)ViewOilType

View Oil Type

Non longlife Oil

Press any key to con.

OilService 1)LonglifeOil►2)NonLonglifeOil3)SetInsp.Interval

VS862 - 2 - 151107 23 ≤ V2.4 SOFTWARE

Pressanykeytoreturntopreviousmenu.3)

Setting Inspection IntervalSet Insp. Interval is used to set oil service interval of different channels ofvariousvehicles.

To enter Set Insp. Interval menuUse 1) UP/DOWN scroll button to select Auto Detect from Oil Service menu,andpressY button.

Press any key to enter 2) Set Insp. Interval menu.

NonLonglifeOil 1)ServiceReset

ServiceReset

RESETOK!

Press any key to con.

OilService

►1)AutoDetect2) Audi3) VW4)Seat5) Skoda

VS862 - 2 - 151107 24 ≤ V2.4 SOFTWARE

It is recommended to use y Auto Detect to enter Set Insp. Interval menu.

Or use 3) UP/DOWN scroll button to select Set Insp. Interval from themenu,andpressY button.

Use 4) UP/DOWNscrollbuttontochangevalueasdesired.

Use 5) Nbuttontomovetonextsetupscreen.

Manual Setup Can’tAutoDetect!PleaseTryOthers.

Press any key to cont.

OilService 1)LonglifeOil2)NonLonglifeOil►3)SetInsp.Interval

MinMil.toService 1/3 ChannelNo 42 (Mil)CurrentValue 9000SetValue <9000>

[N]=Next,[Y]=Save/Exit[︽]/[︾]=ChangeSetup

VS862 - 2 - 151107 25 ≤ V2.4 SOFTWARE

Use6) UP/DOWNscrollbuttontochangevalueasdesired.Use 7) Nbuttontomovetonextsetupscreen.

Use 8) UP/DOWN scroll button to change value as desired, and pressY button.

Differentvehiclesupportsdifferentoilservicechannels;soretrievedychannelnumbersmayvaryfromonevehicle toanother.Normally,avehiclesupports3-5channels.1/3totheupperrightcornerofthescreenindicatesthetotalnumberofysupportedchannelsandtheirsequence.

Use 9) UP/DOWN scrollbuttontoselect<Save>andpressY buttontosaveyour settings.

Mil.SinceService 2/3 ChannelNo 40 (Mil)CurrentValue 700SetValue <700>

[N]=Next,[Y]=Save/Exit[︽]/[︾]=ChangeSetup

TimeSinceService 3/3 ChannelNo 41 (Day)CurrentValue 15SetValue <15>

[N]=Next,[Y]=Save/Exit[︽]/[︾]=ChangeSetup

VS862 - 2 - 151107 26 ≤ V2.4 SOFTWARE

Press any key to return to 10) Main Menu.

Ifyouwanttocontinuetochangevalues,usey UP/DOWN scroll button toselect<Back>andpressY button to return to Min Mil. to Service menu.Ifyouwanttocancelallsetups,useUPy /DOWN scroll button to select <Exit>andpressYbutton,orsimplypressNbuttontoreturntothe Main Menu.

OilService <Back>Save Exit[Back]=Cont.toSet[Save]=SaveSetup[Exit]=CancelSetup

Manual Setup

RESETOK!

Press any key to cont.

sales@sealey.co.uk01284 75750001284 703534

Sole UK DistributorSealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

email

Web

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.